Nanomaterial with high antimicrobial efficacy--copper/polyaniline nanocomposite

Effect of gamma irradiation on properties of the synthesized PANI-Cu nanoparticles assimilated into PS polymer for electromagnetic interference shielding application

Conductive polymer nanocomposites for electromagnetic interference (EMI) shielding are important materials that can be combat the increasingly dangerous radiation pollution arising from electronic equipment and our surrounding environment. In this work, we have synthesized polyaniline-copper nanoparticles (PANI-Cu NPs) by the copper salt based oxidative polymerization method at room temperature and then added with different concentration (0, 1, 3 and 5 wt%) in polystyrene polymer forming PS/ PANI-Cu nanocomposites films by means of the traditional solution casting technique. The formed PANI-Cu NPs were investigated by UV/Vis spectroscopy, X-ray diffraction (XRD), transmission electron microscopy (TEM) and SEM/EDX elemental mapping techniques. On the other hand, the prepared PS/PANI-Cu nanocomposites films were evaluated by UV and SEM, the mechanical properties of the nanocomposites films were evaluated and showed an improvement by added PANI-Cu NPs up to 3 wt% and 50 kGy gamma exposure dose. The PS/PANI-Cu nanocomposites films were examined as electromagnetic interference shielding material. Electromagnetic shielding effectiveness of the produced nanocomposites were tested in the X-band of the radio frequency range namely from 8 to 12 GHz using the vector network analyzer (VNA) and a proper wave guide. All samples were studied before and after 50 kGy gamma-ray irradiation under the same condition of pressure and temperature. The results showed that the nanocomposites have improved shielding properties.

Advances in stabilization of metallic nanoparticle with biosurfactants- a review on current trends

Recently, research based on new biomaterials for stabilizing metallic nanoparticles has increased due to their greater environmental friendliness and lower health risk. Their stability is often a critical factor influencing their performance and shelf life. Nowadays, the use of biosurfactants is gaining interest due to their sustainable advantages. Biosurfactants are used for various commercial and industrial applications such as food processing, therapeutic applications, agriculture, etc. Biosurfactants create stable coatings surrounding nanoparticles to stop agglomeration and provide long-term stability. The present review study describes a collection of important scientific works on stabilization and capping of metallic nanoparticles as biosurfactants. This review also provides a comprehensive overview of the intrinsic properties and environmental aspects of metal nanoparticles coated with biosurfactants. In addition, future methods and potential solutions for biosurfactant-mediated stabilization in nanoparticle synthesis are also highlighted. The objective of this study is to ensure that the stabilized nanoparticles exhibit biocompatible properties, making them suitable for applications in medicine and biotechnology.

Polyaniline-metal oxide coatings for biocidal applications: Mechanisms of activation and deactivation

Metal oxide (MO) coatings (e.g. TiO2, ZnO, and CuO) have shown great promise to inactivate pathogenic bacteria, maintain self-cleaning surfaces, and prevent infectious diseases spread via surface contact. Under light illumination, the antibacterial performance of photoactive MO coatings is determined by reactive oxygen species (ROS) generation. However, several drawbacks, such as photo-corrosion and rapid electron-hole recombination, hinder the ROS production of MO coatings and diminish their antibacterial efficiency. In this study, we employed polyaniline (PANI), an inexpensive and easy-to-synthesize conductive polymer, to fabricate polyaniline-metal oxide composite (PMC) films. The antibacterial performance of PMC films was tested using E. coli as the model bacterium and Lake Michigan water (LMW) as the background medium and revealed enhanced antibacterial performance relative to MO coatings alone (approximately 75-90 % kill of E. coli by PMC coatings in comparison to 20-40 % kill by MO coatings), which is explained by an increase in the ROS yields of PMC. However, with repeated use, the antibacterial performance of the PMC coatings is diminished due to deprotonation of the PANI in the neutral/slightly basic aqueous environment of LMW. Overall, PANI can enhance the antibacterial performance of MO coatings, but efforts need to be directed to preserve or regenerate PMC stability under environmental conditions and applications.

Exploring nanocomposites for controlling infectious microorganisms: charting the path forward in antimicrobial strategies

Nanocomposites, formed by combining a matrix (commonly polymer or ceramic) with nanofillers (nano-sized inclusions like nanoparticles or nanofibers), possess distinct attributes attributed to their composition. Their unique physicochemical properties and interaction capabilities with microbial cells position them as a promising avenue for infectious disease treatment. The escalating prevalence of multi-drug resistant bacteria intensifies the need for alternative solutions. Traditional approaches involve antimicrobial agents like antibiotics, antivirals, and antifungals, targeting specific microbial aspects. This review presents a comprehensive overview of diverse nanocomposite types and highlights the potential of tailored matrix and antibacterial agent selection within nanocomposites to enhance treatment efficacy and decrease antibiotic resistance risks. Challenges such as toxicity, safety, and scalability in clinical applications are also acknowledged. Ultimately, the convergence of nanotechnology and infectious disease research offers the prospect of enhanced therapeutic strategies, envisioning a future wherein advanced materials revolutionize the landscape of medical treatment.

Differential Analysis of Three Copper-Based Nanomaterials with Different Morphologies to Suppress Alternaria alternata and Safety Evaluation

The overuse of copper-based fertilizers and pesticides over the last few decades has resulted in detrimental risks to our environment. Nano-enabled agrichemicals with a high effective utilization ratio have shown great potential for maintaining or minimizing environmental issues in agriculture. Copper-based nanomaterials (Cu-based NMs) serve as a promising alternative to fungicides. Three types of Cu-based NMs with different morphologies were analyzed for their different antifungal effects on Alternaria alternata in this current study. Compared to commercial copper hydroxide water power (Cu(OH)₂ WP), all tested Cu-based NMs, including cuprous oxide nanoparticles (Cu₂O NPs), copper nanorods (Cu NRs) and copper nanowires (Cu NWs), especially Cu₂O NPs and Cu NWs, showed higher antifungal activity against Alternaria alternata. Its EC₅₀ were 104.24 and 89.40 mg L^-1, respectively, achieving comparable activity using a dose approximately 1.6 and 1.9-fold lower. Cu-based NMs could introduce the downregulation of melanin production and soluble protein content. In contrast to trends in antifungal activity, Cu₂O NPs showed the strongest power in regulating melanin production and protein content and similarly exhibited the highest acute toxicity to adult zebrafish compared to other Cu-based NMs. These results demonstrate that Cu-based NMs could offer great potential in plant disease management strategies.

Preparation of Copper-Decorated Activated Carbon Derived from Platamus occidentalis Tree Fiber for Antimicrobial Applications

This study focuses on a greener approach to synthesizing activated carbon by carbonizing Platamus occidentalis tree fibers (TFSA) with 98% H₂SO₄ at 100 °C. The resulted TFSA was employed as an effective adsorbent for copper ions in aqueous media, yielding copper decorated TFSA (Cu@TFSA). The successful adsorption of copper onto the TFSA was proven through extensive characterization techniques. Herein, the TEM and XPS showed that copper nanoparticles were formed in situ on the TFSA surface, without the use of additional reducing and stabilizing agents nor thermal treatment. The surface areas of TFSA and Cu@TFSA were 0.0150 m²/g and 0.3109 m²/g, respectively. Applying the Cu@TFSA as an antimicrobial agent against Escherica coli ( E. coli) and Salmonella resulted in the potential mitigation of complex secondary pollutants from water and wastewater. The Cu@TFSA exhibited outstanding antimicrobial activity against E. coli and Salmonella in both synthetic and raw water samples. This demonstrated a complete growth inhibition observed within 120 min of exposure. The bacteria inactivation took place through the destruction of the bacteria cell wall and was confirmed by the AFM analysis technique. Cu@TFSA has the potential to be used in the water and wastewater treatment sector as antimicrobial agents.

Recent trends and advances in polyindole-based nanocomposites as potential antimicrobial agents: a mini review

Infections caused by multi-drug resistant microbes are a big challenge to the medical field and it necessitates the need for new biomedical agents that can act as potential candidates against these pathogens. Several polyindole based nanocomposites were found to exhibit the ability to release reactive oxygen species (ROS) and hence they show excellent antimicrobial properties. The features of polyindole can be fine-tuned to make them potential alternatives to antibiotics and antifungal medicines. This review clearly portrays the antimicrobial properties of polyindole based nanocomposites, reported so far for biomedical applications. This review will give a clear insight into the scope and possibilities for further research on the biomedical applications of polyindole based nanocomposites.

Investigation on visible light-driven antimicrobial and mechanistic activity of GO/TiO2(V–N) nanocomposite against wound pathogens

GO/TiO2(V–N) is fabricated as a visible light driven efficient antimicrobial material. In the presence of light, GO/TiO2(V–N) was employed as a photocatalytic active material against wound pathogens.

Prospects for the creation of antimicrobial preparations based on copper and copper oxides nanoparticles

The spread of strains of microorganisms that are multidrug resistant to modern antimicrobial drugs is still an urgent problem in the treatment and prevention of infectious diseases and public health in general.Currently, the possibility of using metal nanopreparations in various fields of medicine is being actively studied. Nanoparticles of metals and metal oxides are promising antimicrobial agents and are attracting growing interest due to their effectiveness. Nanoscale copper metal particles have shown high antimicrobial activity againstvarious types of gram-positive and gram-negative bacteria, as well as fungi. Taking into account the potential of copper nanoparticles in antimicrobial therapy, we present an overview of the current state of research related to their antimicrobial properties, consideration of the mechanisms of action, key factors affecting antimicrobial activity, including the polymer matrix. The issues of toxicity and resistance to copper are considered. The advantage of copper nanoparticles over other metal nanoparticles is shown.The studies summarized in this review have shown the promise of copper nanoparticles in the creation of new antimicrobial drugs that can be used in the future to control, prevent, and treat various diseases.

Evaluation of the Safety and Toxicity of the Original Copper Nanocomposite Based on Poly-N-vinylimidazole

A new original copper nanocomposite based on poly-N-vinylimidazole was synthesized and characterized by a complex of modern physicochemical and biological methods. The low cytotoxicity of the copper nanocomposite in relation to the cultured hepatocyte cells was found. The possibility to involve the copper from the nanocomposite in the functioning of the copper-dependent enzyme systems was evaluated during the incubation of the hepatocyte culture with this nanocomposite introduced to the nutrient medium. The synthesized new water-soluble copper-containing nanocomposite is promising for biotechnological and biomedical research as a new non-toxic hydrophilic preparation that is allowed to regulate the work of key enzymes involved in energy metabolism and antioxidant protection as well as potentially serving as an additional source of copper.

CuO Bionanocomposite with Enhanced Stability and Antibacterial Activity against Extended-Spectrum Beta-Lactamase Strains

Worldwide, bacterial resistance to beta-lactam antibiotics is the greatest challenge in public health care. To overcome the issue, metal-based nanoparticles were extensively used as an alternative to traditional antibiotics. However, their unstable nature limits their use. In the present study a very simple, environmentally friendly, one-pot synthesis method that avoids the use of organic solvents has been proposed to design stable, novel nanocomposites. Formulation was done by mixing biogenic copper oxide (CuO) nanomaterial with glycerol and phospholipids isolated from egg yolk in an appropriate ratio at optimum conditions. Characterization was done using dynamic light scattering DLS, Zeta potential, high performance liquid chromatography (HPLC), and transmission electron microscopy (TEM). Further, its antibacterial activity was evaluated against the extended-spectrum beta-lactamase strains based on zone of inhibition and minimal inhibitory concentration (MIC) indices. Results from this study have demonstrated the formulation of stable nanocomposites with a zeta potential of 34.9 mV. TEM results indicated clear dispersed particles with an average of 59.3 ± 5 nm size. Furthermore, HPLC analysis of the egg yolk extract exhibits the presence of phospholipids in the sample and has significance in terms of stability. The newly formed nanocomposite has momentous antibacterial activity with MIC 62.5 μg/mL. The results suggest that it could be a good candidate for drug delivery in terms of bactericidal therapeutic applications.

Hierarchical Metal-Polymer Hybrids for Enhanced CO2 Electroreduction

The design of catalysts with high activity, selectivity, and stability is key to the electroreduction of CO₂ . Herein, we report the synthesis of 3D hierarchical metal/polymer-carbon paper (M/polymer-CP) electrodes by in situ electrosynthesis. The 3D polymer layer on CP (polymer-CP) was first prepared by in situ electropolymerization, then a 3D metal layer was decorated on the polymer-CP to produce the M/polymer-CP electrode. Electrodes with different metals (e.g. Cu, Pd, Zn, Sn) and various polymers could be prepared by this method. The electrodes could efficiently reduce CO₂ to desired products, such as C₂ H₄ , CO, and HCOOH, depending on the metal used. For example, C₂ H₄ could be formed with a Faradaic efficiency of 59.4 % and a current density of 30.2 mA cm^-2 by using a very stable Cu/PANI-CP electrode in an H-type cell. Control experiments and theoretical calculations showed that the 3D hierarchical structure of the metals and in situ formation of the electrodes are critical for the excellent performance.

Development of genistein-loaded gold nanoparticles and their antitumor potential against prostate cancer cell lines

Soy isoflavone genistein (Gen) exerts beneficial effects against prostate cancer cells in vitro and in vivo. However, its use as a chemoprevention/therapeutic agent is largely limited due to its low bioavailability. In this study we synthesized two variants of a new delivery system, genistein-gold nanoparticles conjugates Gen@AuNPs1 and Gen@AuNPs2, by an environmentally friendly method, using a dual role of Gen to reduce Au³⁺ and stabilize the formed AuNPs, with no additional component. The formation of Gen@AuNPs was confirmed via UV-Vis spectroscopy, FTIR, and Raman spectra measurements. The spherical shape and uniform size of Gen@AuNPs1 and Gen@AuNPs2 (10 ± 2 and 23 ± 3 nm, respectively), were determined by transmission electron microscopy. The nano-conjugates also varied in hydrodynamic diameter (65.0 ± 1.7 and 153.0 ± 2.2 nm) but had similar negative zeta potential (-35.0 ± 2.5 and -37.0 ± 1.6 mV), as measured by dynamic light scattering. The Gen loading was estimated to be 46 and 48%, for Gen@AuNPs1 and Gen@AuNPs2, respectively. The antiproliferative activities of GenAuNPs were confirmed by MTT test in vitro on three malignant prostate carcinoma cell lines (PC3, DU 145, and LNCaP), while selectivity toward malignant phenotype was confirmed using non-cancerous MRC-5 cells. Flow cytometric analysis showed that the inhibition on cell proliferation of more potent Gen@AuNPs1 nano-conjugate is comparable with the effects of free Gen. In conclusion, the obtained results, including physicochemical characterization of newly synthesized AuNPs loaded with Gen, cytotoxicity, and IC₅₀ assessments, indicate their stability and bioactivity as an antioxidant and anti-prostate cancer agent, with low toxicity against human primary cells.

Transparent, Water-Repellent, Antiviral, Antistatic, and Flexible Cu-Plasma-Polymerized Fluorocarbon Nanocomposite Thin Films

Polymer thin films containing fluorine are attracting much attention in various high-tech industries owing to their transparency, flexibility, and excellent water repellency. However, the generation of static electricity due to high electrical resistance limits their application. In this study, highly transparent and flexible Cu-plasma-polymerized fluorocarbon (PPFC) nanocomposite thin films that exhibit hydrophobicity and antistatic properties are proposed. These films, obtained using the mid-range frequency sputtering, exhibited a light transmittance of 84.2%, a water contact angle of 94.6°, and a sheet resistance of 1.2 × 10¹² Ω/□. Transmission electron microscopy and small angle X-ray scattering confirmed that Cu nanoparticles with an average size of 4-5 nm were distributed uniformly in the PPFC matrix. In repeated fatigue bending tests, the Cu-PPFC nanocomposite thin films exhibited excellent mechanical robustness and flexibility. Antiviral properties of the Cu-PPFC nanocomposite thin films were evaluated against influenza A virus, and the number decreased by 96.9% after 30 min. Carbon nanotube-Cu-polytetrafluoroethylene composite targets are advantageous for large-area coating and mass production because they can be applied in large-area sputtering and roll-to-roll processes. The transparency, charging characteristics, and water repellency can be easily controlled in Cu-PPFC nanocomposite thin films by controlling the sputtering power density according to the required product. Therefore, these films can be applied in various industries such as flexible displays, medical, automobiles, functional textiles, and aerospace.

Antibacterial and Antiviral Functional Materials: Chemistry and Biological Activity toward Tackling COVID-19-like Pandemics

The ongoing worldwide pandemic due to COVID-19 has created awareness toward ensuring best practices to avoid the spread of microorganisms. In this regard, the research on creating a surface which destroys or inhibits the adherence of microbial/viral entities has gained renewed interest. Although many research reports are available on the antibacterial materials or coatings, there is a relatively small amount of data available on the use of antiviral materials. However, with more research geared toward this area, new information is being added to the literature every day. The combination of antibacterial and antiviral chemical entities represents a potentially path-breaking intervention to mitigate the spread of disease-causing agents. In this review, we have surveyed antibacterial and antiviral materials of various classes such as small-molecule organics, synthetic and biodegradable polymers, silver, TiO2, and copper-derived chemicals. The surface protection mechanisms of the materials against the pathogen colonies are discussed in detail, which highlights the key differences that could determine the parameters that would govern the future development of advanced antibacterial and antiviral materials and surfaces.

Copper-Modified Polymeric Membranes for Water Treatment: A Comprehensive Review

In the last decades, the incorporation of copper in polymeric membranes for water treatment has received greater attention, as an innovative potential solution against biofouling formation on membranes, as well as, by its ability to improve other relevant membrane properties. Copper has attractive characteristics: excellent antimicrobial activity, high natural abundance, low cost and the existence of multiple cost-effective synthesis routes for obtaining copper-based materials with tunable characteristics, which favor their incorporation into polymeric membranes. This study presents a comprehensive analysis of the progress made in the area regarding modified membranes for water treatment when incorporating copper. The notable use of copper materials (metallic and oxide nanoparticles, salts, composites, metal-polymer complexes, coordination polymers) for modifying microfiltration (MF), ultrafiltration (UF), nanofiltration (NF), forward osmosis (FO) and reverse osmosis (RO) membranes have been identified. Antibacterial and anti-fouling effect, hydrophilicity increase, improvements of the water flux, the rejection of compounds capacity and structural membrane parameters and the reduction of concentration polarization phenomena are some outstanding properties that improved. Moreover, the study acknowledges different membrane modification approaches to incorporate copper, such as, the incorporation during the membrane synthesis process (immobilization in polymer and phase inversion) or its surface modification using physical (coating, layer by layer assembly and electrospinning) and chemical (grafting, one-pot chelating, co-deposition and mussel-inspired PDA) surface modification techniques. Thus, the advantages and limitations of these modifications and their methods with insights towards a possible industrial applicability are presented. Furthermore, when copper was incorporated into membrane matrices, the study identified relevant detrimental consequences with potential to be solved, such as formation of defects, pore block, and nanoparticles agglomeration during their fabrication. Among others, the low modification stability, the uncontrolled copper ion releasing or leaching of incorporated copper material are also identified concerns. Thus, this article offers modification strategies that allow an effective copper incorporation on these polymeric membranes and solve these hinders. The article finishes with some claims about scaling up the implementation process, including long-term performance under real conditions, feasibility of production at large scale, and assessment of environmental impact.

Conjugated polymer nanostructures displaying highly photoactivated antimicrobial and antibiofilm functionalities

This work reports the use of conjugated polymer nanostructures (CPNs) as photoactivated antimicrobial compounds against Gram-positive and Gram-negative microorganisms. Two representative CPNs of polythiophene (PEDOT) and polyaniline (PANI) were prepared as nanofibres with an average diameter of 40 nm and length in the micrometer range. Both CPNs exhibited strong antimicrobial activity under UVA irradiation with the same fluence rate as the UVA component of the solar spectrum. The effect was tested using the Gram-positive bacteria Staphylococcus aureus and the Gram-negative bacteria Escherichia coli. The reduction of colony forming units (CFUs) reached >6 log for PEDOT concentrations as low as 33 ng mL-1. For PEDOT nanofibers, a complete inhibition of S. aureus and E. coli growth was reached at 883 ng mL-1 and 333 ng mL-1 respectively. The photoactivation effect of PANI nanofibres on S. aureus and E. coli was also high, with a CFU reduction of about 7 log and 4 log respectively for an exposure concentration of 33 ng mL-1. The antimicrobial activity was only high under light irradiation and was almost negligible for bulk PEDOT and PANI. The effect of polymeric nanofibers could be attributed to the photoinduced generation of reactive oxygen species, which may induce cell membrane damage, eventually leading to bacterial impairment and inhibition of their biofilm forming capacity. CPN PEDOT and PANI coatings were able to keep surfaces free of bacterial attachment and growth even after 20 h of previous contact with exponentially growing cultures in the dark. PEDOT and PANI CPNs demonstrated good cytocompatibility with human fibroblasts and the absence of hemolytic activity. The materials demonstrated advantages in terms of broad antibacterial spectrum, biofilm inhibition, and the absence of acute toxicity for biomedical applications.

Antimicrobial and biological effects of polyaniline/polyvinylpyrrolidone nanocomposites loaded with silver nanospheres/triangles

Two Ag–PANI/PVP nanocomposites were prepared using in situ integration of AgNPs during oxidative aniline polymerization, accelerated by the presence of PVP, which as well minimized the risk of particle agglomeration and macroscopic precipitation.

Dye Separation and Antibacterial Activities of Polyaniline Thin Film-Coated Poly(phenyl sulfone) Membranes

We fabricated a nanofiltration membrane consisting of a polyaniline (PANI) film on a polyphenylsulfone (PPSU) substrate membrane. The PANI film acted as a potent separation enhancer and antimicrobial coating. The membrane was analyzed via scanning electron microscopy and atomic force microscopy to examine its morphology, topography, contact angle, and zeta potential. We aimed to investigate the impact of the PANI film on the surface properties of the membrane. Membrane performance was then evaluated in terms of water permeation and rejection of methylene blue (MB), an organic dye. Coating the PPSU membrane with a PANI film imparted significant advantages, including finely tuned nanometer-scale membrane pores and tailored surface properties, including increased hydrophilicity and zeta potential. The PANI film also significantly enhanced separation of the MB dye. The PANI-coated membrane rejected over 90% of MB with little compromise in membrane permeability. The PANI film also enhanced the antimicrobial activity of the membrane. The bacteriostasis (B R) values of PANI-coated PPSU membranes after six and sixteen hours of incubation with Escherichia coli were 63.5% and 95.2%, respectively. The B R values of PANI-coated PPSU membranes after six and sixteen hours of incubation with Staphylococcus aureus were 70.6% and 88.0%, respectively.

Preparation and of PVA-based compositions with embedded silver, copper and zinc oxide nanoparticles and assessment of their antibacterial properties

A series of poly(vinyl alcohol) (PVA) based liquid compositions with addition of zinc oxide, silver and copper nanoparticles has been prepared. The compositions also contained other consistency-forming organic components. The physico-chemical properties of the products have been determined. Their pH and density have been assessed. Also, the size of nanoparticles has been defined with using a dynamic light scattering technique. The compositions were subjected to XRD, FT-IR and microscopic analysis as well. Thanks to the incorporation of both metal oxide and metallic nanoparticles, it was possible to enrich the products with antibacterial properties. Their inhibiting properties in the growth of microorganisms have been confirmed against both Gram-negative and Gram-positive strains such as E. coli, S. aureus and P. aeruginosa. Thanks to the ability for solidification, the compositions may be applied on a bacterially contaminated surface, and after destroying the microorganisms and its solidification, it may be peeled off along with the dead bacterial film.

Fabrication of monodispersed copper oxide nanoparticles with potential application as antimicrobial agents

Cuprous oxide nanoparticles (Cu2O NPs) were fabricated in reverse micellar templates by using lipopeptidal biosurfactant as a stabilizing agent. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive x-ray spectrum (EDX) and UV-Vis analysis were carried out to investigate the morphology, size, composition and stability of the nanoparticles synthesized. The antibacterial activity of the as-synthesized Cu2O NPs was evaluated against Gram-positive B. subtilis CN2 and Gram-negative P. aeruginosa CB1 strains, based on cell viability, zone of inhibition and minimal inhibitory concentration (MIC) indices. The lipopeptide stabilized Cu2O NPs with an ultra-small size of 30 ± 2 nm diameter exhibited potent antimicrobial activity against both Gram-positive and Gram-negative bacteria with a minimum inhibitory concentration of 62.5 µg/mL at pH5. MTT cell viability assay displayed a median inhibition concentration (IC50) of 21.21 μg/L and 18.65 μg/mL for P. aeruginosa and B. subtilis strains respectively. Flow cytometric quantification of intracellular reactive oxygen species (ROS) using 2,7-dichlorodihydrofluorescein diacetate staining revealed a significant ROS generation up to 2.6 to 3.2-fold increase in the cells treated with 62.5 µg/mL Cu2O NPs compared to the untreated controls, demonstrating robust antibacterial activity. The results suggest that lipopeptide biosurfactant stabilized Cu2O NPs could have promising potential for biocompatible bactericidal and therapeutic applications.

The Role of Nanoparticle Shapes and Structures in Material Characterisation of Polyvinyl Alcohol (PVA) Bionanocomposite Films

Three different types of nanoparticles, 1D Cloisite 30B clay nanoplatelets, 2D halloysite nanotubes (HNTs), and 3D nanobamboo charcoals (NBCs) were employed to investigate the impact of nanoparticle shapes and structures on the material performance of polyvinyl alcohol (PVA) bionanocomposite films in terms of their mechanical and thermal properties, morphological structures, and nanomechanical behaviour. The overall results revealed the superior reinforcement efficiency of NBCs to Cloisite 30B clays and HNTs, owing to their typical porous structures to actively interact with PVA matrices in the combined formation of strong mechanical and hydrogen bondings. Three-dimensional NBCs also achieved better nanoparticle dispersibility when compared with 1D Cloisite 30B clays and 2D HNTs along with higher thermal stability, which was attributed to their larger interfacial regions when characterised for the nanomechanical behaviour of corresponding bionanocomposite films. Our study offers an insightful guidance to the appropriate selection of nanoparticles as effective reinforcements and the further sophisticated design of bionanocomposite materials.

Design and antibacterial activity assessment of “green” synthesized 1,4-disubstituted 1,2,3-triazoles via an Fe3O4/silicalite-1/PVA/Cu(i) nanocomposite catalyzed three component reaction

The preparation of an Fe₃O₄/silicalite-1/PVA/Cu(i) bionanocomposite is presented, completely characterized and applied for the green synthesis of 1,4-disubstituted-1,2,3-triazoles.

Cu nanoparticles constrain segmental dynamics of cross-linked polyethers: a trade-off between non-fouling and antibacterial properties

Copper has a strong bactericidal effect against multi-drug resistant pathogens and polyethers are known for their resistance to biofilm formation. Herein, we combined Cu nanoparticles (NPs) and a polyether plasma polymer in the form of nanocomposite thin films and studied whether both effects can be coupled. Cu NPs were produced by magnetron sputtering via the aggregation in a cool buffer gas whereas polyether layers were synthesized by Plasma-Assisted Vapor Phase Deposition with poly(ethylene oxide) (PEO) used as a precursor. In situ specific heat spectroscopy and XPS analysis revealed the formation of a modified polymer layer around the NPs which propagates on the scale of a few nanometers from the Cu NP/polymer interface and then transforms into a bulk polymer phase. The chemical composition of the modified layer is found to be ether-deficient due to the catalytic influence of copper whereas the bulk polymer phase exhibits the chemical composition close to the original PEO. Two cooperative glass transition phenomena are revealed that belong to the modified polymer layer and the bulk phase. The former is characterized by constrained mobility of polymer segments which manifests itself via a 30 K increase of dynamic glass transition temperature. Furthermore, the modified layer is characterized by the heterogeneous structure which results in higher fragility of this layer as compared to the bulk phase. The Cu NPs/polyether thin films exhibit reduced protein adsorption; however, the constrained segmental dynamics leads to the deterioration of the non-fouling properties for ultra-thin polyether coatings. The films are found to have a bactericidal effect against multi-drug resistant Gram-positive Methicillin-Resistant Staphylococcus aureus and Gram-negative Pseudomonas aeruginosa.

Tailored Ag-Cu-Mg multielemental nanoparticles for wide-spectrum antibacterial coating

Bactericidal nanoparticle coatings are very promising for hindering the indirect transmission of pathogens through cross-contaminated surfaces. The challenge, limiting their employment in nosocomial environments, is the ability of tailoring the coating's physicochemical properties, namely, composition, cytotoxicity, bactericidal spectrum, adhesion to the substrate, and consequent nanoparticles release into the environment. We have engineered a new family of nanoparticle-based bactericidal coatings comprising Ag, Cu, and Mg and synthesized by a green gas-phase technique. These coatings present wide-spectrum bactericidal activity on both Gram-positive and Gram-negative reference strains and tunable physicochemical properties of relevance in view of their "on-field" deployment. The link between material and functional properties is rationalized based on a multidisciplinary and multitechnique approach. Our results pave the way for engineering biofunctional, fully tunable nanoparticle coatings, exploiting an arbitrarily wide number of elements in a straightforward, eco-friendly, high-throughput, one-step process.

Copper accumulation and toxicity in earthworms exposed to CuO nanomaterials: Effects of particle coating and soil ageing

Engineered nanomaterials (ENMs) may be functionalised with a surface coating to enhance their properties, but the ecotoxicity of the coatings and how hazard changes with ageing in soil is poorly understood. This study determined the toxic effect of CuO ENMs with different chemical coatings on the earthworm (Eisenia fetida) in fresh soil, and then after one year in aged soil. In both experiments, earthworms were exposed for 14 days to the CuO materials at nominal concentrations of 200 and 1000 mg Cu kg^-1 dry weight and compared to CuSO₄. In the fresh soil experiment, CuO-COOH was found to be the most acutely toxic of the nanomaterials (survival, 20 ± 50%), with tenfold increase of total Cu in the earthworms compared to controls. Sodium pump activity was reduced in most CuO ENM treatments, although not in the CuSO₄ control. There was no evidence of glutathione depletion or the induction of superoxide dismutase (SOD) activity in any treatment. Histology showed a mild hypoplasia of mucous cells in the epidermis with some nanomaterials. In the aged soil, the CuO-NH₄⁺ was the most acutely toxic ENM (survival 45 ± 3%) and Cu accumulation was lower in the earthworms than in the fresh soil study. Depletion of tissue Mn and Zn concentrations were seen in earthworms in aged soil, while no significant effects on sodium pump or total glutathione were observed. Overall, the study showed some coating-dependent differences in ENM toxicity to earthworms which also changed after a year of ageing the soil.

Antimicrobial and antifouling properties of versatile PPSU/carboxylated GO nanocomposite membrane against Gram-positive and Gram-negative bacteria and protein

Biofouling is a serious issue in membrane-based water and wastewater treatment as it critically compromises the efficacy of the water treatment processes. This investigation demonstrates the antimicrobial and antifouling properties of a nanocomposite membrane system composed of carboxyl-functionalized graphene oxide (COOH-GO) and polyphenylsulfone (PPSU). The PPSU/COOH-GO nanocomposite membrane exhibited excellent antimicrobial properties, achieving maximum bacteriostasis rates of 74.2% and 81.1% against the representative Gram-negative bacteria (Escherichia coli and Pseudomonas aeruginosa, respectively) and 41.9% against the representative Gram-positive bacterium (Staphylococcus aureus). The PPSU/COOH-GO nanocomposite membrane inhibited the attachment, colonization, and the biofilm formation of three species. Antifouling was assessed through filtration experiments using a model foulant bovine serum albumin (BSA). The fouling mechanisms were investigated by Hermia's models (complete blocking, intermediate blocking, standard blocking, and cake formation), and the analysis involved fitting the volumetric flux decline experimental data to models. The fouling study revealed a less irreversible fouling and increased flux recovery ratio for the PPSU/COOH-GO nanocomposite membrane. Complete blocking of pores and cake formation were the major fouling mechanisms for the membrane.

Copper-polyaniline nanocomposite: Role of physicochemical properties on the antimicrobial activity and genotoxicity evaluation

Copper nanoparticles (Cu NPs) have proven to own excellent antimicrobial efficacy, but the problems of easy oxidation and aggregation limit their practical application. Here, nanocomposite based on polyaniline (PANI) and Cu NPs solved this problem and brought additional physicochemical properties that are markedly advantageous for antimicrobial applications. Current work exploits this potential, to examine its time- and concentration-dependent antimicrobial activity, employing E. coli, S. aureus, and C. albicans as a model microbial species. Regarding the presence of polaronic charge carriers in the fibrous polyaniline network, effects of Cu NPs' size and their partially oxidized surfaces (the data were confirmed by HRTEM, FESEM, XRD, Raman and XPS analysis), as well as rapid copper ions release, Cu-PANI nanocomposite showed efficient bactericidal and fungicidal activities at the concentrations ≤1 ppm, within the incubation time of 2 h. Beside the quantitative analysis, the high levels of cellular disruption for all tested microbes were evidenced by atomic force microscopy. Moreover, the minimum inhibitory and bactericidal concentrations of the Cu-PANI nanocomposite were lower than those reported for other nanocomposites. Using such low concentrations is recognized as a good way to avoid its toxicity toward the environment. For this purpose, Cu-PANI nanocomposite is tested for its genotoxicity and influence on the oxidative status of the human cells in vitro.

Contact killing and antimicrobial properties of copper

With the emergence of antibiotic resistance, the interest for antimicrobial agents has recently increased again in public health. Copper was recognized in 2008 by the United States Environmental Protection Agency (EPA) as the first metallic antimicrobial agent. This led to many investigations of the various properties of copper as an antibacterial, antifungal and antiviral agent. This review summarizes the latest findings about 'contact killing', the mechanism of action of copper nanoparticles and the different ways micro-organisms develop resistance to copper.