Microwave-Enhanced Reaction Rates for Nanoparticle Synthesis

Bioinspired graphene-based metal oxide nanocomposites for photocatalytic and electrochemical performances: an updated review

Considering the rapidly increasing population, the development of new resources, skills, and devices that can provide safe potable water and clean energy remains one of the vital research topics for the scientific community. Owing to this, scientific community discovered such material for tackle this issue of environment benign, the new materials with graphene functionalized derivatives show significant advantages for application in multifunctional catalysis and energy storage systems. Herein, we highlight the recent methods reported for the preparation of graphene-based materials by focusing on the following aspects: (i) transformation of graphite/graphite oxide into graphene/graphene oxide via exfoliation and reduction; (ii) bioinspired fabrication or modification of graphene with various metal oxides and its applications in photocatalysis and storage systems. The kinetics of photocatalysis and the effects of different parameters (such as photocatalyst dose and charge-carrier scavengers) for the optimization of the degradation efficiency of organic dyes, phenol compounds, antibiotics, and pharmaceutical drugs are discussed. Further, we present a brief introduction on different graphene-based metal oxides and a systematic survey of the recently published research literature on electrode materials for lithium-ion batteries (LIBs), supercapacitors, and fuel cells. Subsequently, the power density, stability, pseudocapacitance charge/discharge process, capacity and electrochemical reaction mechanisms of intercalation, and conversion- and alloying-type anode materials are summarized in detail. Furthermore, we thoroughly distinguish the intrinsic differences among underpotential deposition, intercalation, and conventional pseudocapacitance of electrode materials. This review offers a meaningful reference for the construction and fabrication of graphene-based metal oxides as effective photocatalysts for photodegradation study and high-performance optimization of anode materials for LIBs, supercapacitors, and fuel cells.

Hard carbon for sodium-ion batteries: progress, strategies and future perspective

Because of its abundant resources, low cost and high reversible specific capacity, hard carbon (HC) is considered as the most likely commercial anode material for sodium-ion batteries (SIBs). Therefore, reasonable design and effective strategies to regulate the structure of HCs play a crucial role in promoting the development of SIBs. Herein, the progress in the preparation approaches for HC anode materials is systematically overviewed, with a special focus on the comparison between traditional fabrication methods and advanced strategies emerged in recent years in terms of their influence on performance, including preparation efficiency, initial coulombic efficiency (ICE), specific capacity and rate capability. Furthermore, the advanced strategies are categorized into two groups: those exhibiting potential for large-scale production to replace traditional methods and those presenting guidelines for achieving high-performance HC anodes from top-level design. Finally, challenges and future development prospects to achieve high-performance HC anodes are also proposed. We believe that this review will provide beneficial guidance to actualize the truly rational design of advanced HC anodes, facilitating the industrialization of SIBs and assisting in formulating design rules for developing high-end advanced electrode materials for energy storage devices.

Physico-Chemical Properties of CdTe/Glutathione Quantum Dots Obtained by Microwave Irradiation for Use in Monoclonal Antibody and Biomarker Testing

In this report, we present the results on the physicochemical characterization of cadmium telluride quantum dots (QDs) stabilized with glutathione and prepared by optimizing the synthesis conditions. An excellent control of emissions and the composition of the nanocrystal surface for its potential application in monoclonal antibody and biomarker testing was achieved. Two samples (QDYellow, QDOrange, corresponding to their emission colors) were analyzed by dynamic light scattering (DLS), and their hydrodynamic sizes were 6.7 nm and 19.4 nm, respectively. Optical characterization by UV-vis absorbance spectroscopy showed excitonic peaks at 517 nm and 554 nm. Photoluminescence spectroscopy indicated that the samples have a maximum intensity emission at 570 and 606 nm, respectively, within the visible range from yellow to orange. Infrared spectroscopy showed vibrational modes corresponding to the functional groups OH-C-H, C-N, C=C, C-O, C-OH, and COOH, which allows for the formation of functionalized QDs for the manufacture of biomarkers. In addition, the hydrodynamic radius, zeta potential, and approximate molecular weight were determined by dynamic light scattering (DLS), electrophoretic light scattering (ELS), and static light scattering (SLS) techniques. Size dispersion and the structure of nanoparticles was obtained by Transmission Electron Microscopy (TEM) and by X-ray diffraction. In the same way, we calculated the concentration of Cd2+ ions expressed in mg/L by using the Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-OES). In addition to the characterization of the nanoparticles, the labeling of murine myeloid cells was carried out with both samples of quantum dots, where it was demonstrated that quantum dots can diffuse into these cells and connect mostly with the cell nucleus.

Cadmium-Based Quantum Dots Alloyed Structures: Synthesis, Properties, and Applications

Cadmium-based alloyed quantum dots are one of the most popular metal chalcogenides in both the industrial and research fields owing to their extraordinary optical and electronic properties that can be manipulated by varying the compositional ratio in addition to size control. This report aims to cover the main information concerning the synthesis techniques, properties, and applications of Cd-based alloyed quantum dots. It provides a comprehensive overview of the most common synthesis methods for these QDs, which include hot injection, co-precipitation, successive ionic layer adsorption and reaction, hydrothermal, and microwave-assisted synthesis methods. This detailed literature highlights the optical and structural properties of both ternary and quaternary quantum dots. Also, this review provides the high-potential applications of various alloyed quantum dots.

Ligand-flexible synthesis of strongly confined perovskite nanocrystals: a microwave synthetic approach

Perovskite nanocrystals (PNCs) and their strongly confined versions have traditionally been synthesized via hot injection methods. However, there is a pressing need for a new synthesis method that offers more flexible surface chemistry, improved optical properties, and greater sample stability. Here we explore and exploit the recently introduced microwave (MW) synthesis method, focusing on temperature and coating ligands, including a polymer ligand for which the hot injection method is unsuitable. The optimized microwave synthetic protocols produce PNCs with better exciton definition, lower polydispersity, and stronger ligand attachment than their hot injection counterparts. A variety of characterization techniques were employed to compare the properties of PNCs produced by the hot injection versus microwave methods. Insight into the molecular basis for the improved PNC properties was provided by FTIR and several NMR experiments that revealed the nature of the attachment of different ligands and their interactions with the PNCs. The overall results demonstrate that MW synthesis is a promising alternative to the HI method, particularly if smaller PNCs with strong quantum confinement are desired.

Microwave synthesis of upconverting nanoparticles with bis(2-ethylhexyl) adipate

A mixture of bis(2-ethylhexyl) adipate and oleic acid provides scale-up potential and speedy heating rates in the microwave-assisted organic synthesis of upconverting nanoparticles with tunable size, crystallinity, and hydrophilic character.

Recent developments in germanium containing clusters in intermetallics and nanocrystals

Multimetallic clusters can be described as building blocks in intermetallics, compounds prepared from all metals and/or semi-metals, and in Zintl phases, a subset of intermetallics containing metals with large differences in electronegativity. In many cases, these intermetallic and Zintl phases provide the first clue for the possibilities of bond formation between metals and semi-metals. Recent advances in multimetallic clusters found in Zintl phases and nanoparticles focusing on Ge with transition metals and semi-metals is presented. Colloidal routes to Ge nanocrystals provide an opportunity for kinetically stabilized Ge-metal and Ge-semi-metal bonding. These routes provide crystalline nanoclusters of Ge, hereafter referred to as nanocrystals, that can be structurally characterized. Compositions of Ge nanocrystals containing transition metals, and the semi-metals, Sb, Bi, and Sn, whose structures have recently been elucidated through EXAFS, will be presented along with potential applications.

DNA-Modified Cobalt Tungsten Oxide Hydroxide Hydrate Nanochains as an Effective Electrocatalyst with Amplified CO Tolerance during Methanol Oxidation

Direct methanol fuel cell technology implementation mainly depends on the development of non-platinum catalysts with good CO tolerance. Among the widely studied transition-metal catalysts, cobalt oxide with distinctively higher catalytic efficiency is highly desirable. Here, we have evolved a simple method of synthesizing cobalt tungsten oxide hydroxide hydrate nanowires with DNA (CTOOH/DNA) and without incorporating DNA (CTOOH) by microwave irradiation and subsequently employed them as electrocatalysts for methanol oxidation. Following this, we examined the influence of incorporating DNA into CTOOH by cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy. The enhanced electrochemical surface area of CTOOH offered readily available electroactive sites and resulted in a higher oxidation current at a lower onset potential for methanol oxidation. On the other hand, CTOOH/DNA exhibited improved CO tolerance and it was evident from the chronoamperometric studies. Herein, we noticed only a 2.5 and 1.8% drop at CTOOH- and CTOOH/DNA-modified electrodes, respectively, after 30 min. Overall, from the results, it was evident that the presence of DNA in CTOOH played an important role in the rapid removal of adsorbed intermediates and regenerated active catalyst centers possibly by creating high density surface defects around the nanochains than bare CTOOH.

A review of the microwave-assisted synthesis of carbon nanomaterials, metal oxides/hydroxides and their composites for energy storage applications

Currently, nanomaterials are considered to be the backbone of modern civilization. Especially in the energy sector, nanomaterials (mainly, carbon- and metal oxide/hydroxide-based nanomaterials) have contributed significantly. Among the various green approaches for the synthesis of these nanomaterials, the microwave-assisted approach has attracted significant research interest worldwide. In this context, it is noteworthy to mention that because of their enhanced surface area, high conducting nature, and excellent electrical and electrochemical properties, carbon nanomaterials are being extensively utilized as efficient electrode materials for both supercapacitors and secondary batteries. In this review article, we briefly demonstrate the characteristics of microwave-synthesized nanomaterials for next-generation energy storage devices. Starting with the basics of microwave heating, herein, we illustrate the past and present status of microwave chemistry for energy-related applications, and finally present a brief outlook and concluding remarks. We hope that this review article will positively convey new insights for the microwave synthesis of nanomaterials for energy storage applications.

Cadmium Selenide Quantum Dots for Solar Cell Applications: A Review

Quantum dot-sensitized solar cells (QDSSCs) are significant energy-producing devices due to their remarkable capability to growing sunshine and produce many electrons/holes pairs, easy manufacturing, and low cost. However, their power conversion efficiency (4%) is usually worse than that of dye-sensitized solar cells (≤12%); this is mainly due to their narrow absorption areas and the charge recombination happening at the quantum dot/electrolyte and Ti O 2 /electrolyte interfaces. Thus, to raise the power conversion efficiency of QDSSC, new counter electrodes, working electrodes, sensitizers, and electrolytes are required. CdSe thin films have shown great potential for use in photodetectors, solar cells, biosensors, light-emitting diodes, and biomedical imaging systems. This article reviews the CdSe nanomaterials that have been recently used in QDSSCs as sensitizers. Their size, design, morphology, and density all noticeably influence the electron injection efficiency and light-harvesting capacity of these devices. A detailed overview of the development of QDSSCs is presented, including their basic principles, the synthesis methods for their CdSe quantum dots, and the device fabrication processes. Finally, the challenges and opportunities of realizing high-performance CdSe QDSSCs are discussed and some future directions are suggested.

A highly sensitive and selective on-off fluorescent sensor based on a complex of polySchiff-Fe2+ for Cr(vi) detection in an aqueous medium

Designing exceptional probes to detect minute quantities of chromium(vi) is of huge importance for the safety and health of the human race. In this study, a green fluorescence emission probe (polyethylene Schiff base-chelated Fe2+ complex) was synthesized by a one-pot synthesis method for the highly selective and sensitive detection of Cr(vi) in an aqueous solution. The complex of polyethylene Schiff-Fe2+ was fully characterized, and it displayed satisfactory stability in the aqueous solution. The fluorescence emission could be quenched specifically by the introduction of Cr(vi) via the oxidation of the Fe2+-centered polyethylene Schiff base complex. The fluorescence intensity decreases linearly with the concentration of Cr(vi), and the corresponding detection limit was calculated to be 0.18 μM. Thus, the obtained fluorescence detection system could be used for Cr(vi) detection in tap water. These features provide potential uses of the as-prepared polyethylene Schiff-Fe2+ complex as a sensor for environmental applications.

Rapid microwave-based method for the preparation of antimicrobial lignin-capped silver nanoparticles active against multidrug-resistant bacteria

Due to the increasing inability of antibiotics to treat multidrug-resistant (MDR) bacteria, metal and metal oxide nanoparticles have been gaining interest as antimicrobial agents. Among those, silver nanoparticles have been used extensively as broad-spectrum antimicrobial agents. Here, we describe a newly-developed, 10-min (120 °C at 5 bar pressure) microwave-assisted synthesis of silver nanoparticles made from the wood biopolymer lignin as a reducing and capping agent. The resulting lignin-capped silver nanoparticles (AgLNPs) had an average particle diameter of 13.4 ± 2.8 nm. Antimicrobial susceptibility assays against a variety of MDR clinical Gram-positive and Gram-negative pathogens revealed a minimal inhibitory concentration (MIC) of AgLNPs ≤5 µg/mL. AgLNPs (10 µg/mL) showed ≤20% cytotoxicity towards monocytic THP-1 cells and were well tolerated when administered subcutaneously in mice at high concentrations (5 mg at a concentration of 100 mg/mL) with no obvious toxicity. AgLNPs showed efficacy in an in vivo infection (abscess) mouse model against MDR Pseudomonas aeruginosa LESB58 and methicillin-resistant Staphylococcus aureus USA300. A significant decrease in abscess sizes was observed for both strains as well as a reduction in bacterial loads of P. aeruginosa after three days. This demonstrates that microwave-assisted synthesis provides an optimized strategy for the production of AgLNPs while maintaining antimicrobial activity in vitro and in vivo.

Microwave Synthesis and Magnetocaloric Effect in AlFe2B2

A promising magnetic refrigerant, AlFe₂B₂, has been prepared for the first time by microwave (MW) melting of a mixture of constituent elements. For comparison, samples of AlFe₂B₂ have been also prepared by arc-melting, traditionally used for the synthesis of this material, and by induction (RF) melting, which was used in the very first report on the synthesis of AlFe₂B₂. Although an excess of Al has to be used to suppress the formation of ferromagnetic FeB, the other byproduct, Al₁₃Fe₄, is easily removed by acid treatment, affording phase-pure samples of AlFe₂B₂. Our analysis indicates that the equimolar Fe/B ratio typically used for the preparation of AlFe₂B₂ might not provide the best synthetic conditions, as it does not account for the full reaction stoichiometry. Furthermore, we find that the initial Al/Fe loading ratio strongly influences magnetic properties of the sample, as judged by the range of ferromagnetic ordering temperatures (T_C = 280-293 K) observed in our experiments. The T_C value increases with the decrease in the Al/Fe ratio, due to the change in the Al/Fe antisite disorder. The use of the same Al/Fe loading ratio in the arc-, RF-, and MW-melting experiments leads to samples with a more consistent T_C of 286-287 K and similar values of the magnetocaloric effect.

InP Quantum Dots: Synthesis and Lighting Applications

InP quantum dots (QDs) are typical III-V group semiconductor nanocrystals that feature large excitonic Bohr radius and high carrier mobility. The merits of InP QDs include large absorption coefficient, broad color tunability, and low toxicity, which render them promising alternatives to classic Cd/Pb-based QDs for applications in practical settings. Over the past two decades, the advances in wet-chemistry methods have enabled the synthesis of small-sized colloidal InP QDs with the assistance of organic ligands. By proper selection of synthetic protocols and precursor materials coupled with surface passivation, the QYs of InP QDs are pushed to near unity with modest color purity. The state-of-the-art InP QDs with appealing optical and electronic properties have excelled in many applications with the potential for commercialization. This work focuses on the recent development of wet-chemistry protocols and various precursor materials for the synthesis and surface modification of InP QDs. Current methods for constructing light-emitting diodes using novel InP-based QDs are also summarized.

Thermal and microwave synthesized SPIONs: Energy effects on the efficiency of nano drug carriers

Superparamagnetic iron oxide nanoparticles (SPIONs) were optimally synthesized employing two energy sources viz. thermal and microwave using low temperature co-precipitation process. Both methods yielded particles with optimum physicochemical properties for biomedical applications like smaller size (~6--7 nm), narrow size distribution (standard deviation ~1.6-1.7 nm) and good magnetic parameters (saturation magnetisation ~53 emu/g at 9 T). Simplified process made use of domestic oven. After coating by amino acid serine, successful loading (>8 wt%) of drug Doxorubicin was achieved for both SPIONs. Microwave sample showed equivalently efficient drug loading despite half the serine coating. Findings were confirmed by various techniques like X-ray diffraction (XRD), transmission electron microscopy (TEM), Vibrating sample magnetometer (VSM) and thermo gravimetric analysis (TGA) etc. Differences in thermal homogeneities and efficiency of heat transfer between two energy modes affected the properties of synthesized SPIONs. Differences were observed in amount of serine coating, drug release behaviour and in vitro experiments on A549 cells like internalisation and cell viability data. About 59 and 39% pH and time dependent drug release at pH 5 was obtained for thermal and microwave sample respectively. In vitro experiments confirmed the successful internalisation and cell death, supporting the suitability of SPIONS as efficient targeted drug carriers. Despite lesser drug release, microwave sample showed comparable in vitro results. Study emphasizes the role and importance of energy in affecting the efficiency and functional behaviour of SPIONs as nano drug carriers. Being biocompatible and magnetic these particles can be applied successfully as efficient targeted drug delivery agents.

Microwave-Assisted Synthesis of High-Energy Faceted TiO2 Nanocrystals Derived from Exfoliated Porous Metatitanic Acid Nanosheets with Improved Photocatalytic and Photovoltaic Performance

A facile one-pot microwave-assisted hydrothermal synthesis of rutile TiO₂ quadrangular prisms with dominant {110} facets, anatase TiO₂ nanorods and square nanoprisms with co-exposed {101}/[111] facets, anatase TiO₂ nanorhombuses with co-exposed {101}/{010} facets, and anatase TiO₂ nanospindles with dominant {010} facets were reported through the use of exfoliated porous metatitanic acid nanosheets as a precursor. The nanostructures and the formation reaction mechanism of the obtained rutile and anatase TiO₂ nanocrystals from the delaminated nanosheets were investigated. The transformation from the exfoliated metatitanic nanosheets with distorted hexagonal cavities to TiO₂ nanocrystals involved a dissolution reaction of the nanosheets, nucleation of the primary [TiO₆]⁸⁻ monomers, and the growth of rutile-type and anatase-type TiO₂ nuclei during the microwave-assisted hydrothermal reaction. In addition, the photocatalytic activities of the as-prepared anatase nanocrystals were evaluated through the photocatalytic degradation of typical carcinogenic and mutagenic methyl orange (MO) under UV-light irradiation at a normal temperature and pressure. Furthermore, the dye-sensitized solar cell (DSSC) performance of the synthesized anatase TiO₂ nanocrystals with various morphologies and crystal facets was also characterized. The {101}/[111]-faceted pH2.5-T175 nanocrystal showed the highest photocatalytic and photovoltaic performance compared to the other TiO₂ samples, which could be attributed mainly to its minimum particle size and maximum specific surface area.

Physical and optical studies of Gd2 O2 S:Eu3+ nanophosphors by microwave irradiation and γ-irradiation methods

Gd₂ O₂ S:Eu³⁺ nanophosphors have been successfully synthesized using microwave irradiation and γ-irradiation methods with polyvinyl pyrrolidone as a stabilizer. The physical and luminescence spectra were compared. The morphologies of both Gd₂ O₂ S:Eu³⁺ nanophosphors were in the hexagonal phase and mainly consisted of spherical nanostructures with diameters of ~90 nm and ~50 nm for both microwave irradiation and γ-irradiation methods. Upon 325 nm of ultraviolet (UV) light excitation, strong red emissions (626 nm) were observed for both methods; these emissions corresponded to the ⁵ D₀ →⁷ F₂ transition of Eu³⁺ ions. However, Gd₂ O₂ S:Eu³⁺ nanophosphors following microwave treatment showed better luminescence intensity than Gd₂ O₂ S:Eu³⁺ nanophosphors treated with γ-irradiation. This difference was attributed to the crystallinity phase and surface quenching effects of Gd₂ O₂ S:Eu³⁺ nanophosphors. The reaction mechanisms of Gd₂ O₂ S:Eu³⁺ nanophosphors in both methods are discussed in detail.

Microwave-assisted Synthesis of Hexagonal Gold Nanoparticles Reduced by Organosilane (3-Mercaptopropyl)trimethoxysilane

A novel synthesis of hexagonal gold nanoparticles (Au NPs) via hydrolyzed organosilane (3-mercaptopropyl)trimethoxysilane (MPTMS) using an ultrafast and environmentally friendly method is presented in this study. For the first time, organosilane MPTMS is used for chemical reduction of auric acid under ultrafast microwave irradiation. To the best of our knowledge, the use of organosilane for the synthesis of Au NPs has not been reported. The entire one-step process is convenient, rapid and cost-effective, as well as eco-friendly under alcohol-free aqueous media. Different characterization methods were carried out to investigate the properties of synthesized gold nanoparticles. transmission electron microscopy and scanning electron microscopy were used to investigate the morphology of as-synthesized Au NPs, while X-ray powder diffraction was applied to obtain the crystalline nature. Nuclear magnetic resonance was used to track the hydrolysis of organosilane MPTMS, which is employed for the first time as a reducing agent for the synthesis of Au NPs. The impact from microwave irradiation time and power, as well as the catalytic property of as-synthesized Au NPs, was investigated via ultraviolet-visible spectroscopy. The as-synthesized products include gold nanohexagon and two-dimensional hexagonal gold nanoplatelets, both of which are single-crystal with (1 1 1) planes as basal surfaces. From UV-vis spectra, it is found that the facile water-based fabrication of hexagonal Au NPs began within seconds of microwave irradiation and the size growth increased with the microwave power and time. Moreover, the efficient reduction of 4-nitrophenol to 4-aminophenol in the presence of as-synthesized Au NPs was observed, exhibiting a remarkable catalytic activity. The present simple, rapid and convenient one-step microwave process possess high scalability and useful for future applications such as catalysis, medical, biological, plasmonic sensors and electronics.

Microwave irradiation directly excites semiconductor catalyst to produce electric current or electron-holes pairs

Generally, photon of Microwave (MW) electromagnetic waves have long been thought to be lower energy, which could not excite metals or semiconductor materials to generate electric current and electron-holes pairs (e⁻_cb + h⁺_vb). In this paper, we report an unexpected, Microwave “photoelectric effect”, when MW irradiates on the semiconductor materials, leading to generate electric current and electron-holes pairs (e⁻_cb + h⁺_vb), on the semiconductor materials and on the MW catalyst. Further, we show that the action mechanism of Microwave “photoelectric effect” made water adsorbing on the surface of Microwave catalyst transform into hydroxyl radical (∙OH). Thus, this study has revealed the principle of generation Microwave “photoelectric effect” under MW irradiation, and the mechanism of MW catalytic oxidation degradation of organic in the wastewater and the mechanism of MW reduction method for preparation of nano-particle metal supported catalysts. Our findings challenge the classic view of MW irradiation only as heating method, which cannot excite to produce electric current and electron-holes pairs (e⁻_cb + h⁺_vb). Our findings will open new field to use MW technology for MW catalytic oxidation degradation of organics in the wastewater, and for MW reduction method of metal supported catalysts preparation.

A repertoire of biomedical applications of noble metal nanoparticles

The emerging properties of noble metal nanoparticles are attracting huge interest from the translational scientific community. In this feature article, we highlight recent advances in the adaptation of noble metal nanomaterials and their biomedical applications in therapeutics, diagnostics and sensing.

Cobalt tungsten oxide hydroxide hydrate (CTOHH) on DNA scaffold: an excellent bi-functional catalyst for oxygen evolution reaction (OER) and aromatic alcohol oxidation

CTOHH-DNA, a newly developed catalyst utilized for both electrocatalytic OER and aromatic alcohol oxidation reaction with excellent activities.

Gallium – a versatile element for tuning the photoluminescence properties of InP quantum dots

Depending on the gallium precursor, the photoluminescence of indium phosphide quantum dots is either blue- or red-shifted.

Microwave assisted synthesis of heterometallic 3d–4f M4Ln complexes

We describe the solvent-free microwave assisted synthesis and magnetic properties of a series of 3d–4f complexes of formula [M₄Ln(OH)₂(chp)₄(SALOH)₅(H₂O)(MeCN)(Solv)] (Solv = MeOH, MeCN, H₂O, M = Ni(ii), Co(ii); Ln = La, Gd, Dy, Tb).

Methylene Blue-Fortified Molybdenum Trioxide Nanoparticles: Harnessing Radical Scavenging Property

A hybrid nanosystem with impeccable cellular imaging and antioxidant functionality is demonstrated. The microwave irradiation-derived molybdenum trioxide nanoparticles (MoO₃ NPs) were surface-functionalized with the cationic dye molecule, methylene blue (MB), which enables superior UV-visible absorbance and fluorescence emission wavelengths potential for bioimaging. The radical scavenging property of the pristine MoO₃ NPs and MoO₃-MB NPs were studied in vivo using Caenorhabditis elegans as the model system. Heat shock-induced oxidative stress in C. elegans was significantly resolved by the MoO₃-MB NPs, in agreement with the in vitro radical scavenging study by electron paramagnetic resonance spectroscopy. Hybrid nanostructures of MoO₃-MB demonstrate synergistic benefits in intracellular imaging with intrinsic biocompatibility and antioxidant behavior, which can facilitate application as advanced healthcare materials toward bioimaging and clinical therapeutics.

One-Pot Gram-Scale Synthesis of Hydrogen-Terminated Silicon Nanoparticles

Silicon nanoparticles (Si NPs) are highly attractive materials for typical quantum dots functions, such as in light-emitting and bioimaging applications, owing to silicon's intrinsic merits of minimal toxicity, low cost, high abundance, and easy and highly stable functionalization. Especially nonoxidized Si NPs with a covalently bound coating serve well in these respects, given the minimization of surface defects upon hydrosilylation of H-terminated Si NPs. However, to date, methods to obtain such H-terminated Si NPs are still not easy. Herein, we report a new synthetic method to produce size-tunable robust, highly crystalline H-terminated Si NPs (4-9 nm) using microwave irradiation within 5 min at temperatures between 25 and 200 °C and their further covalent functionalization. The key step to obtain highly fluorescent (quantum yield of 7-16%) green-red Si NPs in one simple step is the reduction of triethoxysilane and (+)-sodium l-ascorbate, yielding routinely ∼1 g of H-Si NPs via a highly scalable route in 5-15 min. Subsequent functionalization via hydrosilylation yielded Si NPs with an emission quantum yield of 12-14%. This approach can be used to easily produce high-quality H-Si NPs in gram-scale quantities, which brings the application of functionalized Si NPs significantly closer.

Solid-liquid separation: an emerging issue in heavy metal wastewater treatment

Solid-liquid separation (SLS) plays a dominant role in various chemical industries. Nowadays, low efficiency of SLS also become a significant problem in heavy metal (HM) wastewater treatment, affecting the effluent quality (HM concentration and turbidity) and overall process economy. In this context, we summarize here the occurrence of solids in HM wastewater, as well as typical SLS operations used in HM wastewater treatment, including sedimentation, flotation, and centrifugation. More important, this article reviews the improvement of the SLS operations by some technologies, including coagulation, flocculation, ballasted method, seeding method, granular sludge strategy, and external field enhancement. It is noted that abiological granular sludge strategy and magnetic field enhancement often possess higher SLS efficiency (faster settling velocity or shorter separation time) than other methods. Hence, the two strategies stand out as promising tools for improving SLS in HM wastewater treatment, but further research is required regarding scalability, economy, and reliability.

Rapid Induction and Microwave Heat-Up Syntheses of CdSe Quantum Dots

The production of nanoparticles on an industrial scale requires an approach other than the widely used hot-injection method. In this work, two heat-up methods are applied to nanoparticle synthesis. The induction heating method produces CdSe quantum dots with ultrasmall properties in seconds. Initial flow-through experiments demonstrate that induction heating continuously produces quantum dots. These results are compared with those from microwave synthesis, which produces quantum dots on a longer timescale but provides fast, continuous heating. Both methods can produce quantum dots within seconds because of rapid heating. In addition, different precursors, single source and separate source, give different results, ultimately providing a handle to control quantum dot properties.