Quantification of Tight Binding to Surface-Immobilized Phospholipid Vesicles Using Surface Plasmon Resonance: Binding Constant of Phospholipase A2

A Novel Methodology for Economical Scale-Up of TiO2 Nanotubes Fabricated on Ti and Ti Alloys

The prospective use of nanotechnology for medical devices is increasing. While the impact of material surface nanopatterning on the biological response is convincing, creating a large surface area with such nanotechnology remains an unmet challenge. In this paper, we describe, for the first time, a reproducible scale-up manufacturing technique for creating controlled nanotubes on the surfaces of Ti and Ti alloys. We describe an average of approximately 7.5-fold increase in cost and time efficiency with regards to the generation of 20, 50, and 100 nm diameter nanotubes using an anodisation technique. These novel materials have great potential in the medical field through their influence on cellular activity, in particular, protein absorption, focal adhesion, and osteoinduction. In this paper, we provide a step-by-step guide to optimise an anodisation system, starting with design rationale, proof of concept, device upscaling, consistency, and reproducibility check, followed by cost and efficiency analysis. We show that the optimised device can produce a high number of anodised specimens with customisable specimen shape at reduced cost and time, without compromising the repeatability and consistency. The device can fabricate highly uniform and vertically oriented TiO2 nanotube layer with desired pore diameters.

A Comparative Study of Phosphatidylcholine versus Phosphatidylserine-Based Solid Supported Membranes for the Preparation of Liposome-Rich Interfaces

Solid supported membranes (SSMs) are usually formed by an hybrid octadecanethiol/phosphatidylcholine (PC) bilayer supported by a gold electrode. Recently, it was shown that phosphatidylserine (PS) in place of PC can promote a more effective accumulation of lipid vesicles on the SSM surface when Ca²⁺ and Mg²⁺ ions are present in the external environment. Here we performed a detailed comparative study of the vesicle adsorption process onto PC- and PS-SSMs by employing surface plasmon resonance (SPR), electrochemical impedance spectroscopy (EIS), and atomic force microscopy (AFM). SPR analysis has demonstrated a higher affinity of the PS-SSM surface for the phospholipid vesicles. Both SPR and EIS measurements suggest that adsorption of lipid vesicles on the PC-SSM tends to a saturating value, whereas a continuous and progressive vesicle adsorption occurs on the PS-SSM surface following subsequent liposome additions. AFM analysis pointed out a systematic flattening of the adsorbed vesicles on the PS-SSM surface. We interpreted our results as due to the strong coordinating action of the high amount of divalent cations accumulated at the negatively charged PS-SSM surface, whereas a lower amount of cations is present on the dipolar PC-SSM surface, which can therefore adsorb only a limited number of vesicles.

Calcium-dependent hydrolysis of supported planar lipids was triggered by honey bee venom phospholipase A2with the right orientation at the interface

Hydrolysis of planar phospholipids catalyzed by honey bee venom phospholipase A₂(bvPLA₂) was studied.

UV-patternable nanocomposite containing CdSe and PbS quantum dots as miniaturized luminescent chemo-sensors

We have developed a patternable nanocomposite sensor based on luminescent CdSe QDs and a polyisoprene-based photoresist (PIP) as host matrix that showed chemosensing response against MET and EDA in vapour with a LOD around 0.1 pg and 15 ng, respectively.

Label-free quantitative detection of tumor-derived exosomes through surface plasmon resonance imaging

Exosomes are endosome-derived membrane vesicles carrying proteins and nucleic acids that are involved in cellular functions such as intercellular communication, protein and RNA secretion, and antigen presentation. Therefore, exosomes serve as potential biomarkers for many diseases including cancer. Because exosomes are difficult to enrich or purify from biofluids, quantification of exosomes is tedious and inaccurate. Here, we present a real-time, label-free, and quantitative method to detect and characterize tumor-derived exosomes without enrichment or purification. Utilizing surface plasmon resonance imaging (SPRi) in combination with antibody microarrays specific to the extracellular domains of exosome membrane proteins, exosomes in tumor cell culture medium can be quantitatively detected. We found a positive correlation between the metastatic potential of tumor cell lines and exosome secretion. This method provides an easy, efficient, and novel way to detect exosome secretion and thus an avenue toward the diagnosis and prognosis prediction of cancer.

Trapping of vesicles on patterned surfaces by physisorption for potential biosensing applications

The pre-defined selective positioning of a controlled number of vesicles on a rigid substrate is crucial in many potential applications such as diagnostics, biosensors, lab-on-a chip, microanalyses and reaction chambers. In this paper, the vesicles made up of block copolymer using Poly [-(2-methyloxazoline) -poly- (dimethylsiloxane)-poly- (2-methyloxazoline)] (ABA) with dimensions of 100-200 nm are trapped by physisorption on hydrophilic surfaces. We discuss the protocols established for vesicle trapping. The optimum conditions obtained for physisorption is 15 minutes incubation followed by one cycle of DI water rinse. Trapping of 1-10 vesicles in lobe shape micro-wells fabricated by photo lithography using photoresist on UltraStick(™) slides was demonstrated. To overcome the issue of amalgamation of emitted light from optically sensitive photoresist and fluorescently tagged vesicles, an alternative approach of Si/SiO(2) microwell array coupled with APTES (3-AminoPropylTriEthoxySilane) treated bottom surfaces was developed.

PPIP5K1 modulates ligand competition between diphosphoinositol polyphosphates and PtdIns(3,4,5)P3 for polyphosphoinositide-binding domains

We describe new signalling consequences for PPIP5K1 (diphosphoinositol pentakisphosphate kinase type 1)-mediated phosphorylation of InsP6 and 5-InsP7 to 1-InsP7 and InsP8. In NIH 3T3 cells, either hyperosmotic stress or receptor activation by PDGF (platelet-derived growth factor) promoted translocation of PPIP5K1 from the cytoplasm to the plasma membrane. The PBD1 (polyphosphoinositide-binding domain) in PPIP5K1 recapitulated that translocation. Mutagenesis of PBD1 to reduce affinity for PtdIns(3,4,5)P3 prevented translocation. Using surface plasmon resonance, we found that PBD1 association with vesicular PtdIns(3,4,5)P3 was inhibited by InsP6 and diphosphoinositol polyphosphates. However, the inhibition by PPIP5K1 substrates (IC50: 5-InsP7=5 μM and InsP6=7 μM) was substantially more potent than that of the PPIP5K1 products (IC50: InsP8=32 μM and 1-InsP7=43 μM). This rank order of ligand competition with PtdIns(3,4,5)P3 was also exhibited by the PH (pleckstrin homology) domains of Akt (also known as protein kinase B), GRP1 (general receptor for phosphoinositides 1) and SIN1 (stress-activated protein kinase-interaction protein 1). We propose that, in vivo, PH domain binding of InsP6 and 5-InsP7 suppresses inappropriate signalling ('noise') from stochastic increases in PtdIns(3,4,5)P3. That restraint may be relieved by localized depletion of InsP6 and 5-InsP7 at the plasma membrane following PPIP5K1 recruitment. We tested this hypothesis in insulin-stimulated L6 myoblasts, using mTOR (mechanistic/mammalian target of rapamycin)-mediated phosphorylation of Akt on Ser473 as a readout for SIN1-mediated translocation of mTORC (mTOR complex) 2 to the plasma membrane [Zoncu, Efeyan and Sabatini (2011) Nat. Rev. Mol. Cell Biol. 12, 21-35]. Knockdown of PPIP5K1 expression was associated with a 40% reduction in Ser473 phosphorylation. A common feature of PtdIns(3,4,5)P3-based signalling cascades may be their regulation by PPIP5K1.

Harnessing fluid-driven vesicles to pick up and drop off Janus particles

Using dissipative particle dynamics (DPD) simulations, we model the interaction between nanoscopic lipid vesicles and Janus nanoparticles in the presence of an imposed flow. Both the vesicle and Janus nanoparticles are localized on a hydrophilic substrate and immersed in a hydrophilic solution. The fluid-driven vesicle successfully picks up Janus particles on the substrate and transports these particles as cargo along the surface. The vesicle can carry up to four particles as its payload. Hence, the vesicles can act as nanoscopic "vacuum cleaners", collecting nanoscopic debris localized on the floors of the fluidic devices. Importantly, these studies reveal how an imposed flow can facilitate the incorporation of nanoparticles into nanoscale vesicles. With the introduction of a "sticky" domain on the substrate, the vesicles can also robustly drop off and deposit the particles on the surface. The controlled pickup and delivery of nanoparticles via lipid vesicles can play an important step in the bottom-up assembly of these nanoparticles within small-scale fluidic devices.

Cholesterol--a biological compound as a building block in bionanotechnology

Cholesterol is a molecule with many tasks in nature but also a long history in science. This feature article highlights the contribution of this small compound to bionanotechnology. We discuss relevant chemical aspects in this context followed by an overview of its self-assembly capabilities both as a free molecule and when conjugated to a polymer. Further, cholesterol in the context of liposomes is reviewed and its impact ranging from biosensing to drug delivery is outlined. Cholesterol is and will be an indispensable player in bionanotechnology, contributing to the progress of this potent field of research.

Model membrane platforms for biomedicine: case study on antiviral drug development

As one of the most important interfaces in cellular systems, biological membranes have essential functions in many activities such as cellular protection and signaling. Beyond their direct functions, they also serve as scaffolds to support the association of proteins involved in structural support, adhesion, and transport. Unfortunately, biological processes sometimes malfunction and require therapeutic intervention. For those processes which occur within or upon membranes, it is oftentimes difficult to study the mechanism in a biologically relevant, membranous environment. Therefore, the identification of direct therapeutic targets is challenging. In order to overcome this barrier, engineering strategies offer a new approach to interrogate biological activities at membrane interfaces by analyzing them through the principles of the interfacial sciences. Since membranes are complex biological interfaces, the development of simplified model systems which mimic important properties of membranes can enable fundamental characterization of interaction parameters for such processes. We have selected the hepatitis C virus (HCV) as a model viral pathogen to demonstrate how model membrane platforms can aid antiviral drug discovery and development. Responsible for generating the genomic diversity that makes treating HCV infection so difficult, viral replication represents an ideal step in the virus life cycle for therapeutic intervention. To target HCV genome replication, the interaction of viral proteins with model membrane platforms has served as a useful strategy for target identification and characterization. In this review article, we demonstrate how engineering approaches have led to the discovery of a new functional activity encoded within the HCV nonstructural 5A protein. Specifically, its N-terminal amphipathic, α-helix (AH) can rupture lipid vesicles in a size-dependent manner. While this activity has a number of exciting biotechnology and biomedical applications, arguably the most promising one is in antiviral medicine. Based on the similarities between lipid vesicles and the lipid envelopes of virus particles, experimental findings from model membrane platforms led to the prediction that a range of medically important viruses might be susceptible to rupturing treatment with synthetic AH peptide. This hypothesis was tested and validated by molecular virology studies. Broad-spectrum antiviral activity of the AH peptide has been identified against HCV, HIV, herpes simplex virus, and dengue virus, and many more deadly pathogens. As a result, the AH peptide is the first in class of broad-spectrum, lipid envelope-rupturing antiviral agents, and has entered the drug pipeline. In summary, engineering strategies break down complex biological systems into simplified biomimetic models that recapitulate the most important parameters. This approach is particularly advantageous for membrane-associated biological processes because model membrane platforms provide more direct characterization of target interactions than is possible with other methods. Consequently, model membrane platforms hold great promise for solving important biomedical problems and speeding up the translation of biological knowledge into clinical applications.

Facile fabrication of an interface for online coupling of microchip CE to surface plasmon resonance

Background: The aim was to develop a simple route to coupling microchip CE (MCE) to surface plasmon resonance (SPR). MCE is a microfluidic technology that utilizes microfabrication techniques to connect interacting fluid reservoirs. Its advantages include rapid analysis (typically seconds), easy integration of multiple analytical steps and parallel operation. SPR detects changes in refractive index within a short distance from the surface of a thin metal film as variations in light intensity reflected from the back of the film and, thus, does not require labeling. There is a great demand for developing hyphenated techniques like MCE–SPR that are fast, sensitive and inexpensive to analyze biological materials. Materials & Methods: The separation channel and flow cell exist as overlapping regions constructed during the microchip production and buffer solution was delivered mechanically. Such a design has successfully isolated the electrical field inherent in the MCE from the SPR detector. Consequently, the potential interference to the SPR signal (or modulation of the density of surface plasmons at the gold chip) is circumvented. Results: The limits of detection for bovine serum albumin and sodium fluorescein were determined to be 7.5 µM and 3.1 mM, respectively. Conclusion: The technique described, herein, has been successfully applied in the separation of two species. The method offers the advantages of a near zero connection dead volume, electrical shielding from the separation voltage and minimization of the mass transfer effect.

Azide-reactive liposome for chemoselective and biocompatible liposomal surface functionalization and glyco-liposomal microarray fabrication

Chemically selective liposomal surface functionalization and liposomal microarray fabrication using azide-reactive liposomes are described. First, liposome carrying PEG-triphenylphosphine was prepared for Staudinger ligation with azide-containing biotin, which was conducted in PBS buffer (pH 7.4) at room temperature without a catalyst. Then, immobilization and microarray fabrication of the biotinylated liposome onto a streptavidin-modified glass slide via the specific streptavidin/biotin interaction were investigated by comparing with directly formed biotin-liposome, which was prepared by the conventional liposome formulation of lipid-biotin with all other lipid components. Next, the covalent microarray fabrication of liposome carrying triphenylphosphine onto an azide-modified glass slide and its further glyco-modification with azide-containing carbohydrate were demonstrated for glyco-liposomal microarray fabrication via Staudinger ligation. Fluorescence imaging confirmed the successful immobilization and protein binding of the intact immobilized liposomes and arrayed glyco-liposomes. The azide-reactive liposome provides a facile strategy for membrane-mimetic glyco-array fabrication, which may find important biological and biomedical applications such as studying carbohydrate-protein interactions and toxin and antibody screening.

Construction and structural analysis of tethered lipid bilayer containing photosynthetic antenna proteins for functional analysis

The construction and structural analysis of a tethered planar lipid bilayer containing bacterial photosynthetic membrane proteins, light-harvesting complex 2 (LH2), and light-harvesting core complex (LH1-RC) is described and establishes this system as an experimental platform for their functional analysis. The planar lipid bilayer containing LH2 and/or LH1-RC complexes was successfully formed on an avidin-immobilized coverglass via an avidin-biotin linkage. Atomic force microscopy (AFM) showed that a smooth continuous membrane was formed there. Lateral diffusion of these membrane proteins, observed by a fluorescence recovery after photobleaching (FRAP), is discussed in terms of the membrane architecture. Energy transfer from LH2 to LH1-RC within the tethered membrane was observed by steady-state fluorescence spectroscopy, indicating that the tethered membrane can mimic the natural situation.

Cationized albumin-biocoatings for the immobilization of lipid vesicles

Tethered lipid membranes or immobilized lipid vesicles are frequently used as biomimetic systems. In this article, the authors presented a suitable method for efficient immobilization of lipid vesicles onto a broad range of surfaces, enabling analysis by quantitative methods even under rigid, mechanical conditions-bare surfaces such as hydrophilic glass surfaces as well as hydrophobic polymer slides or metal surfaces such as gold. The immobilization of vesicles was based on the electrostatic interaction of zwitterionic or negatively charged lipid vesicles with two types of cationic chemically modified bovine serum albumin (cBSA) blood plasma proteins (cBSA-113 and cBSA-147). Quantitative analysis of protein adsorption was performed as the cBSA coatings were characterized by atomic force microscopy, surface zeta potential measurement, fluorescence microscopy, and surface plasmon spectroscopy, revealing a maximal surface coverage 270-280 ng/cm(2) for 0.02 mg/ml cBSA on gold. Small unilamellar vesicles as well as giant unilamellar vesicles (GUVs) were readily immobilized (∼15 min) on cBSA coated surfaces. GUVs with 5-10 mol% negatively charged 1,2,-dipalmitoyl-sn-glycero-3-phosphoglycerol remained stable in liquid for at least 5 weeks.

Ordering transitions in nematic liquid crystals induced by vesicles captured through ligand-receptor interactions

We report that phospholipid vesicles incorporating ligands, when captured from solution onto surfaces presenting receptors for these ligands, can trigger surface-induced orientational ordering transitions in nematic phases of 4'-pentyl-4-cyanobiphenyl (5CB). Specifically, whereas avidin-functionalized surfaces incubated against vesicles composed of 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC) were observed to cause the liquid crystal (LC) to adopt a parallel orientation at the surface, the same surfaces incubated against biotinylated vesicles (DOPC and 1,2-dioleoyl-sn-glycero-3-phosphoethanolamine-N-(biotinyl) (biotin-DOPE)) caused the homeotropic (perpendicular) ordering of the LC. The use of a combination of atomic force microscopy (AFM), ellipsometry and quantitative fluorimetry, performed as a function of vesicle composition and vesicle concentration in solution, revealed the capture of intact vesicles containing 1% biotin-DOPE from buffer at the avidin-functionalized surfaces. Subsequent exposure to water prior to contact with the LC, however, resulted in the rupture of the majority of vesicles into interfacial multilayer assemblies with a maximum phospholipid loading set by random close packing of the intact vesicles initially captured on the surface (5.1 ± 0.2 phospholipid molecules/nm(2)). At high concentrations of biotinylated lipid (>10% biotin-DOPE) in the vesicles, the limiting lipid loading was measured to be 4.0 ± 0.3 phospholipid molecules/nm(2), consistent with the maximum phospholipid loading set by the spontaneous formation of a bilayer during incubation with the biotinylated vesicles. We measured the homeotropic ordering of the LC on the surfaces independently of the initial morphology of the phospholipid assembly captured on the surface (intact vesicle, planar multilayer). We interpret this result to infer the reorganization of the phospholipid bilayers either prior to or upon contact with the LCs such that interactions of the acyl chains of the phospholipid and the LC dominate the ordering of the LC, a conclusion that is further supported by quantitative measurements of the orientation of the LC as a function of the phospholipid surface density (>1.8 molecules/nm(2) is required to cause the homeotropic ordering of the LC). These results and others presented herein provide fundamental insights into the interactions of phospholipid-decorated interfaces with LCs and thereby provide guidance for the design of surfaces on which phospholipid assemblies captured through ligand-receptor recognition can be reported via ordering transitions in LCs.

Liposome and lipid bilayer arrays towards biosensing applications

Sensitive and selective biosensors for high-throughput screening are having an increasing impact in modern medical care. The establishment of robust protein biosensing platforms however remains challenging, especially when membrane proteins are involved. Although this type of proteins is of enormous relevance since they are considered in >60% of the pharmaceutical drug targets, their fragile nature (i.e., the requirement to preserve their natural lipid environment to avoid denaturation and loss of function) puts strong additional prerequisites onto a successful biochip. In this review, the leading approaches to create lipid membrane-based arrays towards the creation of membrane protein biosensing platforms are described. Liposomes assembled in micro- and nanoarrays and the successful set-ups containing functional membrane proteins, as well as the use of liposomes in networks, are discussed in the first part. Then, the complementary approaches to create cell-mimicking supported membrane patches on a substrate in an array format will be addressed. Finally, the progress in assembling free-standing (functional) lipid bilayers over nanopore arrays for ion channel sensing will be reported. This review illustrates the rapid pace by which advances are being made towards the creation of a heterogeneous biochip for the high-throughput screening of membrane proteins for diagnostics, drug screening, or drug discovery purposes.

Surface-bound cytomimetic assembly based on chemoselective and biocompatible immobilization and further modification of intact liposome

A surface-bound cytomimetic assembly based on chemically selective and biocompatible immobilization and further modification of intact liposome is described. Liposomes carrying PEG-triphenylphosphine were chemoselectively immobilized onto azide-modified glass slides through Staudinger ligation, followed by modification with azide-modified lactose as a model biomolecule through Staudinger ligation to afford the surface-bound cytomimetic assembly. The intact liposome immobilized and modified and its protein binding activity were confirmed by fluorescence imaging, fluorescent dye releasing kinetics, and AFM techniques. The resultant surface-bound cytomimetic assembly showed sustained stability and fluorescent dye releasing kinetics and specific protein binding activity. The reported method provides a robust platform for preparation of a complex immobilized liposome system with multifunctional components, which mimics the cell surface in both geographical and content features and thus will find important biomedical applications.

Interfacial binding dynamics of bee venom phospholipase A2 investigated by dynamic light scattering and quartz crystal microbalance

Bee venom phospholipase A(2) (bvPLA(2)) is part of the secretory phospholipase A(2) (sPLA(2)) family whose members are active in biological processes such as signal transduction and lipid metabolism. While controlling sPLA(2) activity is of pharmaceutical interest, the relationship between their mechanistic actions and physiological functions is not well understood. Therefore, we investigated the interfacial binding process of bvPLA(2) to characterize its biophysical properties and gain insight into how membrane binding affects interfacial activation. Attention was focused on the role of membrane electrostatics in the binding process. Although dynamic light scattering experiments indicated that bvPLA(2) does not lyse lipid vesicles, a novel, nonhydrolytic activity was discovered. We employed a supported lipid bilayer platform on the quartz crystal microbalance with dissipation sensor to characterize this bilayer-disrupting behavior and determined that membrane electrostatics influence this activity. The data suggest that (1) adsorption of bvPLA(2) to model membranes is not primarily driven by electrostatic interactions; (2) lipid desorption can follow bvPLA(2) adsorption, resulting in nonhydrolytic bilayer-disruption; and (3) this desorption is driven by electrostatic interactions. Taken together, these findings provide evidence that interfacial binding of bvPLA(2) is a dynamic process, shedding light on how membrane electrostatics can modulate interfacial activation.

Assembly and structure of alpha-helical peptide films on hydrophobic fluorocarbon surfaces

The structure, orientation, and formation of amphiphilic alpha-helix model peptide films on fluorocarbon surfaces has been monitored with sum frequency generation (SFG) vibrational spectroscopy, near-edge x-ray absorption fine structure (NEXAFS) spectroscopy, and x-ray photoelectron spectroscopy (XPS). The alpha-helix peptide is a 14-mer of hydrophilic lysine and hydrophobic leucine residues with a hydrophobic periodicity of 3.5. This periodicity yields a rigid amphiphilic peptide with leucine and lysine side chains located on opposite sides. XPS composition analysis confirms the formation of a peptide film that covers about 75% of the surface. NEXAFS data are consistent with chemically intact adsorption of the peptides. A weak linear dichroism of the amide pi( *) is likely due to the broad distribution of amide bond orientations inherent to the alpha-helical secondary structure. SFG spectra exhibit strong peaks near 2865 and 2935 cm(-1) related to aligned leucine side chains interacting with the hydrophobic surface. Water modes near 3200 and 3400 cm(-1) indicate ordering of water molecules in the adsorbed-peptide fluorocarbon surface interfacial region. Amide I peaks observed near 1655 cm(-1) confirm that the secondary structure is preserved in the adsorbed peptide. A kinetic study of the film formation process using XPS and SFG showed rapid adsorption of the peptides followed by a longer assembly process. Peptide SFG spectra taken at the air-buffer interface showed features related to well-ordered peptide films. Moving samples through the buffer surface led to the transfer of ordered peptide films onto the substrates.

Liposome characterization by quartz crystal microbalance measurements and atomic force microscopy

This chapter reviews liposome characterization by quartz crystal microbalance (QCM) measurements and atomic force microscopy (AFM). In many studies, AFM imaging is simply used to image liposomes with resolution often that does not allow morphological analysis. Although liposome size can be obtained by processing AFM images, it is found that liposomes flatten upon surface adsorption or immobilization. Liposome stability and stiffness have been characterized by using AFM imaging or AFM force measurements, although the latter method, using a microsphere attached on the AFM cantilever, seems more appropriate to limit liposome damage and to obtain more quantitative analysis, such as the Young's modulus. Investigation of liposome layers by QCM revealed that liposomes can be detected from a combined analysis of frequency and bandwidth shifts. However, QCM by itself provides only limited information on liposomes. QCM can be used to assess the presence of a layer and also to discriminate between rigid and viscoelastic ones. Liposome properties have been derived from QCM curves, but often this requires making hypotheses that are difficult to assess. AFM and QCM analyses need to be combined with other techniques to provide complementary information.

Nanoparticle-assisted surface immobilization of phospholipid liposomes

Phospholipid liposomes (100-200 nm diameter) are deposited onto solid substrates after stabilizing them against fusion with the solid by allowing charged nanoparticles to adsorb at approximately 25% surface coverage. The immobilized vesicles remain stable over a period of days. Epifluorescence imaging shows that they diffuse freely over surfaces with the same charge but adsorb tightly onto surfaces with opposite charge. Nanoparticle adsorption to surface patterns of opposite charge provides a facile method to create large-scale surface-supported arrays of intact liposomes. This surface attachment method is simple chemically and applies generally for solid surfaces that can be hydrophobic or hydrophilic. Offering routes to localize proteins and other vesicle-contained objects at surfaces in tailored spatial patterns, these immobilized liposome arrays may find diverse applications in the emerging field of nanobiotechnology.

Biomimetic tethered lipid membranes designed for membrane-protein interaction studies

The complexity of the biological membranes restricts their direct investigation at the nanoscale. Lipid bilayer membranes have been developed as a model of biological membranes in order to allow the interaction and insertion of peptides and membrane proteins in a functional manner. Promising models have been developed in the past two decades and tethered bilayer design traduces constant improvement of membrane models. The formation of protein free solid tethered membranes can be achieved by direct vesicle fusion, Langmuir-Blodgett, Langmuir-Schaffer transfers, self assembly of various building blocks such as thiol on gold, silane on quartz, grafting of polymers, as well as ligand receptor recognition. In this review, the current state of different tethered bilayer membrane will be described. We will focus on critical analysis of the main advantages/drawbacks of each kind of model construction and their ability to allow protein incorporation in non-denaturing conditions. Some of the current drawbacks encountered in these biomimetic models can be overcome using an innovative tethered bilayer design based on a reliable and fast formation method. The successful protein incorporation of the Adenylate Cyclase produced by Bordetella pertussis and the voltage dependent anion channel (VDAC) was demonstrated on this model.

Avidin Decorated Core–Shell Nanoparticles for Biorecognition Studies by Elastic Light Scattering

In this paper, a straightforward method based on elastic light scattering is shown to provide a sensitive and reliable tool for the quantitative determination of protein-ligand interactions that occur at the surface of suitably designed core-shell nanoparticles. The assay makes use of monodisperse nanocolloids that have minimal optical contrast with the aqueous environment. By properly coating the particles with avidin and oligo(ethylene glycol)-based amphiphiles, we developed a hybrid system that combines the availability of standard ligands with the necessary bioinvisibility towards the accidental adsorption of nonspecific macromolecules. This probe was employed to detect interactions between different kinds of biotinylated proteins, and it revealed high specificity and affinities in the low nanomolar range. In particular, we obtained an efficient avidin anchorage of biotinylated protein A on the surface of the nanoparticles, which we exploited as a functional probe for the rapid, quantitative, picomolar detection of human IgG antibodies. Overall, these light-scattering-based nanosensors appear as a simple and highly informative tool for proteomics studies.

Fabrication and characterization of contact lenses bearing surface-immobilized layers of intact liposomes

Intact liposomes were immobilized onto soft contact lenses. In the first step, polyethylenimine was covalently bounded onto the hydroxyl groups available on the surface of a commercial contact lens (Hioxifilcon B). Then, NHS-PEG-biotin molecules were bounded onto the surface amine groups by carbodiimide chemistry. NeutrAvidin were bounded onto the PEG-biotin layer. Liposomes containing PEG-biotinylated lipids were docked onto the surface-immobilized NeutrAvidin. Consecutive addition of further NeutrAvidin and liposome layers enabled fabrication of multilayers. Multilayers of liposomes were also produced by exposing contact lenses coated with NeutrAvidin to liposome aggregates produced by the addition of free biotin in solution. XPS revealed the immobilization of the different layers. By blocking with excess biotin surface-immobilized NeutrAvidin on contact lenses bearing PEG-biotin layers produced under cloud point conditions, ELISA showed that the docking of NeutrAvidin was dependent on biotin-NeutrAvidin affinity binding, with little evidence for nonspecific physisorption; however, it was not possible to differentiate specific versus nonspecific binding of NeutrAvidin attached onto PEG-biotin layers grafted without cloud point conditions. AFM imaging revealed liposome sizes of 106 and 155 nm for layers of liposomes produced (i) by the consecutive addition of further NeutrAvidin and liposomes and (ii) by the exposure of NeutrAvidin-coated contact lenses to liposome aggregates, respectively. The release kinetics of a fluorescent dye demonstrated that intact liposomes had been immobilized onto contact lens surfaces. The stability of surface-immobilized liposomes onto contact lens surfaces showed temperature dependence. Surface-bound liposomes can be stored up to 1 month at 4 degrees C with little release of their content.

Atomic force microscopy observation of highly arrayed phospholipid bilayer vesicle on a gold surface

Tapping mode atomic force microscopy (TM-AFM) imaging of a phospholipid bilayer vesicle (liposome) immobilized on a gold surface was performed to investigate morphologies of the electrode surfaces produced through application of three different sample preparation methods. We compared both methods from a morphological viewpoint using TM-AFM images. Liposomes, composed of zwitterionic and anionic phospholipids, were prepared by extrusion. Results indicate that the surface with immobilized L1-liposome, which was fabricated by the amino coupling method, seemed to form large amounts of aggregated or fused liposomes. In contrast, L2-liposome-containing 1-octadecanthiol that was directly attached on the gold surface using thiol-gold binding force was immobilized as a uniform surface topology without liposome aggregation. Finally, we attempted to arrange individual L3-liposome, prepared by mixing zwitterionic and anionic phospholipids, onto the gold layer by electron-beam (e-beam) lithography technique. A third method, L3-liposome formation on the sensor surface, is greatly anticipated for biosensor applications.

A paradigm shift in the field of molecular recognition at the air-water interface: from static to dynamic

The air-water interface has been recognized as a useful medium for implementation of molecular recognition of aqueous guests since the initial reports of that phenomenon in 1985. Generally, however, there has been no emphasis on the dynamism of the air-water interface despite the fact that that is one of its most unique characteristics, especially when compared with other solid surfaces. In this review, we introduce several of the advances in molecular recognition from the viewpoint of their dynamic properties. Finally, molecular recognition through dynamic cavity formation at the air-water interface is highlighted as being the most advanced example. In the field of molecular recognition, it is clear that a paradigm shift from static to dynamic has been realized.

Surface plasmon resonance in protein-membrane interactions

Surface plasmon resonance (SPR) has become one of the most important techniques for studying macromolecular interactions. The most obvious advantages of SPR over other techniques are: direct and rapid determination of association and dissociation rates of binding process, no need for labelling of protein or lipids, and small amounts of sample used in the assay (often nM concentrations of proteins). In biochemistry, SPR is used mainly to study protein-protein interactions. On the other hand, protein-membrane interactions, although crucial for many cell processes, are less well studied. Recent advances in the preparation of stable membrane-like surfaces and the commercialisation of sensor chips has enabled widespread use of SPR in protein-membrane interactions. One of the most popular is Biacore's L1 sensor chip that allows capture of intact liposomes or even subcellular preparations. Lipid specificity of protein-membrane interactions can, therefore, be easily studied by manipulating the lipid composition of the immobilised membrane. The number of published papers has increased steadily in the last few years and the examples include domains or proteins that participate in cell signalling, pore-forming proteins, membrane-interacting peptides, coagulation factors, enzymes, amyloidogenic proteins, prions, etc. This paper gives a brief overview of different membrane-mimetic surfaces that can be prepared on the surface of SPR chips, properties of liposomes on the surface of L1 chips and some selected examples of protein-membrane interactions studied with such system.

Membrane-mimetic films containing thrombomodulin and heparin inhibit tissue factor-induced thrombin generation in a flow model

Membrane-mimetic thin films containing thrombomodulin (TM) and/or heparin were produced and their capacity to inhibit thrombin generation evaluated in a continuous flow system. Tissue factor (TF) along with TM and heparin were immobilized in spatially restricted zones as components of a membrane-mimetic film. Specifically, TF was positioned as an upstream trigger for thrombin generation and TM and/or heparin positioned over the remaining downstream portion of test films. Peak and steady-state levels of thrombin were decreased by antithrombin III (ATIII), as well as by surface bound heparin and TM. Although physiologic concentrations of ATIII have the capacity to significantly inhibit thrombin activity, surface bound TM and heparin nearly abolished steady-state thrombin responses. In particular, surface bound TM appears to be superior to heparin in reducing local thrombin concentrations. These studies are the first to demonstrate the additive effect of surface bound heparin and TM as a combined interactive strategy to limit TF-induced thrombin formation.

Fabrication and characterization of heparin functionalized membrane-mimetic assemblies

A membrane-mimetic assembly incorporating surface bound heparin was fabricated as a system to improve the hemocompatibility of blood-contacting devices. As a model system, heparin was chemically modified by end-point conjugation to biotin and immobilized onto membrane-mimetic thin films via biotin-streptavidin interactions. Heparin surface density, determined by radiochemical titration, confirmed that surface density was directly related to the molar concentration of biotinylated lipid within the assembled membrane-mimetic film. The capacity of surface bound heparin to promote ATIII-mediated thrombin inactivation was investigated in a parallel plate flow chamber under simulated venous and arterial wall shear rates of 50 and 500 s(-1), respectively. Significantly, we observed that the rate of thrombin inactivation approached a maximum at a heparin surface concentration greater than 4.4 pmol/cm(2) (61 ng/cm(2)). In the process, mass transport limited regimes were identified for heparin potentiated thrombin inactivation under both simulated venous and arterial conditions.

Real-time measurement of solute partitioning to lipid monolayers

The interaction of a peripheral protein with a lipid-water interface can show a pronounced dependence on the composition and two-dimensional packing density of the lipids that comprise the interface. We report a novel optical method for measuring the adsorption of macromolecules, such as proteins and nucleic acids, and smaller solutes, such as drugs, to lipid monolayers at the gas-liquid interface. Using fluorescence emission from proteins and a small molecule, we demonstrate that the emissions from these solutes when in the aqueous phase and when associated with the monolayer can be temporally separated. Such separation allows measurement of the extent of solute adsorption, spectral characterization of the adsorbed solute, and characterization of lipid organization using adsorption kinetics. The method does not require, but is compatible with, the solute having different spectral properties in the bulk and surface phases. Indeed, if optical signals from adsorbed and soluble solute are the same or their relationship is known, absolute surface excess of adsorbed solute can be calculated without independent calibration. With appropriate instrumental configuration, the method should be adaptable for screening solutes for interaction with planar monolayers having both well-defined composition and adjustable lipid packing density.

Probing the structure of supported membranes and tethered oligonucleotides by fluorescence interference contrast microscopy

Fluorescence interference contrast microscopy (FLIC) is a powerful method to structurally characterize fluorescent objects with nanometer-scale resolution in the z direction. Here we use FLIC to characterize the water layer underlying supported membranes and membrane-tethered double-stranded oligonucleotides. FLIC measurements of supported membranes containing the lipid-anchored fluorescent dye DiI in both leaflets indicate the thickness of the water layer separating the solid support and the lower lipid leaflet is 1.3 +/- 0.2 nm. Addition of cobalt(II) chloride to a DiI-supported membrane quenches the fluorescence in the top leaflet of the supported membrane; FLIC measurements of this system precisely locate the DiI to the bottom leaflet. These experiments confirm the accuracy of the model and parameters used to determine the water layer thickness, demonstrate the ability to differentiate between fluorescent objects whose average position differs by approximately 1.9 nm, and provide a widely applicable method to test the resolution of other high-z-resolution fluorescent microscopies. FLIC measurements of Alexa-labeled double-stranded oligonucleotides tethered to a supported membrane indicate that the DNA double helix is oriented perpendicular to the surface. Complications that arise from uncertainly in the orientation of the fluorophore are discussed. Several improvements in FLIC methodology are described. These stringent tests of the resolution of FLIC and the ability to unambiguously determine fluorescent lipid distribution provide structural insight on assemblies at membrane interfaces and permit the detection of even subtle changes at such interfaces.

Patterning polymerized lipid vesicles with soft lithography

The applications of soft lithography in patterning polymerized lipid vesicles of 1,2-bis(tricosa-10,12-diynoyl)-sn-glycero-3-phosphocholine on glass substrates are reported. We demonstrate that the polymerized vesicles can be used as a high molecular weight ink to be transferred from a PDMS stamp onto a glass substrate to form two-dimensional stripes with a controlled separation. By combining channel flow with dewetting within microfluidic networks, we assemble the polymerized vesicle into three-dimensional stripes and one-dimension lines on glass substrates. Atomic force microscopy shows that these patterned vesicle structures are stable on glass substrates. The simple, stable, and precise immobilization of lipid vesicles on solid substrates will open up the possibility of integrating them in biosensors and microelectronic devices.

Fibronectin conformational changes induced by adsorption to liposomes

One of the major drawbacks of drug delivery techniques that utilize liposomes as carriers is that they are often cleared from the body before they can deliver their therapeutic cargo. It is well known that serum proteins can adsorb to these drug delivery vehicles and influence their uptake by phagocytic cells. For this reason, protein adsorption to liposomes has been extensively quantified, and strategies have been developed to minimize protein adsorption to improve drug delivery. However, the conformation of proteins on surfaces can play an even greater role in controlling cell behavior than the quantity of adsorbed protein. We have therefore used fluorescence resonance energy transfer (FRET) to measure changes in the structure of fibronectin (Fn)--a key serum protein involved in phagocytosis--upon interaction with phosphatidylcholine (PC) liposomes. Our experiments reveal that fibronectin opens up from its inactive, compact conformation upon interaction with gel phase PC liposomes. We also used FRET to estimate a physiologically relevant dissociation constant, KD=1.1 nM, for the interaction. Conformational changes in serum proteins may result in the exposure of otherwise concealed recognition sites and therefore influence the interaction of liposomes with phagocytic cells.

Investigating porcine pancreatic phospholipase A2 action on vesicles and supported planar bilayers using a quartz crystal microbalance with dissipation

We present an investigation of the activity of porcine pancreatic phospholipase A2 towards phospholipids. The phospholipids are presented in three different ways, namely as tethered vesicles, intact surface-bound vesicles, and supported planar bilayers (SPBs). The process is followed using a quartz crystal microbalance which measures both the frequency shift and the energy dissipation factor. This technique is very sensitive not only to the mass of the material deposited on the crystal, but also to its viscoelasticity. The breakdown of the phospholipid vesicles and bilayers consequently gives rise to very large signal changes. Enzyme binding is separated from vesicle hydrolysis using nonhydrolyzable ether lipids. Intact and tethered vesicles give rise to the same profile, indicating that direct immobilization of the vesicles does not affect hydrolysis significantly. The data fit well to a Voight-based model describing the change in film structure with time. Initial enzyme binding to intact vesicles is accompanied by a significant increase in layer thickness as well as a decrease in viscosity and shear modulus. This effect, which is less pronounced in SPBs, is probably mainly due to the accumulation of hydrolysis products in the vesicle prior to rupture of the vesicles and release of bound water, since it disappears when lysolipid is included in the vesicles prior to hydrolysis.

Monitoring the kinetics and thermodynamics of interfacial enzymatic catalysis by differential scanning calorimetry

Using phase transition profile as an indicator of thermodynamic property and phase transition heat as the second indicator of the percentage of substrates unhydrolyzed, differential scanning calorimetry has been used to observe in detail the kinetics and thermodynamics of phospholipase A(2)-catalyzed 1,2-dipalmitoyl-sn-glycero-3-phosphocholine large unilamellar vesicle (LUV) hydrolysis. Phase transition profiles show that the original LUV almost completely changes into a novel aggregate at the end of the latency, followed by an abrupt activation of the reaction. The phase transition profiles are asymmetric between the heating and cooling curves, indicating a thermodynamic mesostatic property of the system. The reaction in activated phase follows a single first-order kinetics and all of the substrates in vesicles can be hydrolyzed. All these evidences indicate that the products and substrates can freely exchange between the outer and the inner layers of the vesicles and the membrane of the vesicle in the activated phase is permeable. This permeability favors the exchange of the substrates and products, thus, resulting in the activation of the fast reaction.

Immobilized liposome layers for drug delivery applications: inhibition of angiogenesis

Liposomes were immobilized onto the surface of perfluorinated polymer tape samples and tissue culture polystyrene well-plates using a multilayer immobilization strategy. In the first step, a thin interfacial bonding layer with surface aldehyde groups was deposited from a glow discharge struck in acetaldehyde vapour. Polyethylenimine was then covalently bound onto the aldehyde groups by reductive amination, followed by covalent binding of NHS-PEG-biotin molecules onto the surface amine groups by carbodiimide chemistry. Next, NeutrAvidin protein molecules were bound onto the PEG-biotin layer. Finally, liposomes containing PEG-biotinylated lipids were docked onto the remaining binding sites of the surface-immobilized NeutrAvidin molecules. AFM was used to image surface-bound liposomes and revealed a density well below close packing. The release characteristics of the surface-bound liposomes were measured by the fluorescence intensity changes of carboxyfluorescein upon release. Liposomes filled with sodium orthovanadate were surface immobilized and used in two in vitro angiogenesis assays. Marked differences compared to various control samples were observed, demonstrating the utility of drug-filled, surface-bound liposomes for evoking localized, controlled biological host responses proximal to an implanted biomedical device.