Dynamic Evolution of a Cathode Interphase Layer at the Surface of LiNi0.5Co0.2Mn0.3O2 in Quasi-Solid-State Lithium Batteries

Customized Li+ Solvation Sheath at the Poly(ethylene oxide)-Based Electrolyte/Ultrahigh-Nickel Cathode Interface toward Room-Temperature Solid-State Lithium Batteries

The matching of poly(ethylene oxide) (PEO)-based electrolytes with ultrahigh-nickel cathode materials is crucial for designing new-generation high-energy-density solid-state lithium metal batteries (SLMBs), but it is limited by serious interfacial side reactions between PEO and ultrahigh-nickel materials. Here, a high-concentration electrolyte (HCE) interface with a customized Li+ solvation sheath is constructed between the cathode and the electrolyte. It induces the formation of an anion-regulated robust cathode/electrolyte interface (CEI), reduces the unstable free-state solvent, and finally achieves the compatibility of PEO-based electrolytes with ultrahigh-nickel cathode materials. Meanwhile, the corrosion of the Al current collector caused by lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) ions is prevented by lithium difluoro(oxalato)borate (LiDFOB) ions. The synergistic effect of the double lithium salt is achieved by a well-tailored ratio of TFSI- and DFOB- in the first solvation sheath of Li+. Compared with reported PEO-based SLMBs matched with ultrahigh-nickel (Ni ≥ 90%) cathodes, the SLMB in this work delivers a high discharge specific capacity of 216.4 mAh g-1 (0.1C) even at room temperature. This work points out a direction to optimize the cathode/electrolyte interface.

Improving the interfacial stability of ultrahigh-nickel cathodes with PEO-based electrolytes by targeted chemical reactions

Benefiting from high energy density of ultrahigh-nickel cathode materials and good safety of PEO-based electrolytes, PEO-based ultrahigh-nickel solid-state lithium batteries (SLMBs) are considered to be new-generation energy storage devices. However, the incompatibility of ultrahigh-nickel cathode materials and PEO-based electrolytes is the main challenge due to serious interfacial side reactions. Therefore, the modification of the cathode/electrolyte interface is crucial. Herein, the residual lithium on the surface of LiNi0.9Co0.06Mn0.04O2 is utilized to construct an interfacial coating layer by reacting with H3BO3. The in situ formed xLi2O-B2O3 coating layer (LBO1-NCM) with high ionic conductivity can be regulated with different crystal structures during the sintering process. Besides, an all-solid-state three-electrode cell is fabricated, which verifies that the xLi2O-B2O3 coating can effectively stabilize the interface. Astonishingly, uneven Li anode deposition is observed in SLMBs, which is caused by the breakage of PEO molecular chains due to the strong oxidation of the cathode, while this crosstalk is also suppressed by the xLi2O-B2O3 coating layer. Consequently, Li|PEO|LBO1-NCM achieves a substantially improved electrochemical performance, exhibiting 90.5% of capacity retention after 100 cycles for the coin cell and 80.3% of capacity retention after 200 cycles for the pouch cell. Apparently, the targeted modification of interfaces should be paid as much attention as electrolyte optimization in SLMBs.

Tailoring Electric Double Layer by Cation Specific Adsorption for High-Voltage Quasi-Solid-State Lithium Metal Batteries

The interfacial instability of high-nickel layered oxides severely plagues practical application of high-energy quasi-solid-state lithium metal batteries (LMBs). Herein, a uniform and highly oxidation-resistant polymer layer within inner Helmholtz plane is engineered by in situ polymerizing 1-vinyl-3-ethylimidazolium (VEIM) cations preferentially adsorbed on LiNi0.83Co0.11Mn0.06O2 (NCM83) surface, inducing the formation of anion-derived cathode electrolyte interphase with fast interfacial kinetics. Meanwhile, the copolymerization of [VEIM][BF4] and vinyl ethylene carbonate (VEC) endows P(VEC-IL) copolymer with the positively-charged imidazolium moieties, providing positive electric fields to facilitate Li+ transport and desolvation process. Consequently, the Li||NCM83 cells with a cut-off voltage up to 4.5 V exhibit excellent reversible capacity of 130 mAh g-1 after 1000 cycles at 25 °C and considerable discharge capacity of 134 mAh g-1 without capacity decay after 100 cycles at -20 °C. This work provides deep understanding on tailoring electric double layer by cation specific adsorption for high-voltage quasi-solid-state LMBs.

In Situ Electrochemical Atomic Force Microscopy: From Interfaces to Interphases

The electrochemical interface formed between an electrode and an electrolyte significantly affects the rate and mechanism of the electrode reaction through its structure and properties, which vary across the interface. The scope of the interface has been expanded, along with the development of energy electrochemistry, where a solid-electrolyte interphase may form on the electrode and the active materials change properties near the surface region. Developing a comprehensive understanding of electrochemical interfaces and interphases necessitates three-dimensional spatial resolution characterization. Atomic force microscopy (AFM) offers advantages of imaging and long-range force measurements. Here we assess the capabilities of AFM by comparing the force curves of different regimes and various imaging modes for in situ characterizing of electrochemical interfaces and interphases. Selected examples of progress on work related to the structures and processes of electrode surfaces, electrical double layers, and lithium battery systems are subsequently illustrated. Finally, this review provides perspectives on the future development of electrochemical AFM.

Unveil the origin of voltage oscillation for sodium-ion batteries operating at -40 °C

Voltage oscillation at subzero in sodium-ion batteries (SIBs) has been a common but overlooked scenario, almost yet to be understood. For example, the phenomenon seriously deteriorates the performance of Na3V2(PO4)3 (NVP) cathode in PC (propylene carbonate)/EC (ethylene carbonate)-based electrolyte at -20 °C. Here, the correlation between voltage oscillation, structural evolution, and electrolytes has been revealed based on theoretical calculations, in-/ex-situ techniques, and cross-experiments. It is found that the local phase transition of the Na3V2(PO4)3 (NVP) cathode in PC/EC-based electrolyte at -20 °C should be responsible for the oscillatory phenomenon. Furthermore, the low exchange current density originating from the high desolvation energy barrier in NVP-PC/EC system also aggravates the local phase transformation, resulting in severe voltage oscillation. By introducing the diglyme solvent with lower Na-solvent binding energy, the voltage oscillation of the NVP can be eliminated effectively at subzero. As a result, the high capacity retentions of 98.3% at -20 °C and 75.3% at -40 °C are achieved. The finding provides insight into the abnormal SIBs degradation and brings the voltage oscillation behavior of rechargeable batteries into the limelight.

From Liquid to Solid-State Batteries: Li-Rich Mn-Based Layered Oxides as Emerging Cathodes with High Energy Density

Li-rich Mn-based (LRMO) cathode materials have attracted widespread attention due to their high specific capacity, energy density, and cost-effectiveness. However, challenges such as poor cycling stability, voltage deca,y and oxygen escape limit their commercial application in liquid Li-ion batteries. Consequently, there is a growing interest in the development of safe and resilient all-solid-state batteries (ASSBs), driven by their remarkable safety features and superior energy density. ASSBs based on LRMO cathodes offer distinct advantages over conventional liquid Li-ion batteries, including long-term cycle stability, thermal and wider electrochemical windows stability, as well as the prevention of transition metal dissolution. This review aims to recapitulate the challenges and fundamental understanding associated with the application of LRMO cathodes in ASSBs. Additionally, it proposes the mechanisms of interfacial mechanical and chemical instability, introduces noteworthy strategies to enhance oxygen redox reversibility, enhances high-voltage interfacial stability, and optimizes Li+ transfer kinetics. Furthermore, it suggests potential research approaches to facilitate the large-scale implementation of LRMO cathodes in ASSBs.

Thin Solid Polymer Electrolyte with High-Strength and Thermal-Resistant via Incorporating Nanofibrous Polyimide Framework for Stable Lithium Batteries

Polyethylene oxide (PEO) based polymer electrolytes show promise in expanding the practical applications of lithium (Li) batteries. However, their applications in Li batteries are usually restricted owing to the lack of mechanical strength, poor oxidative stability, and relatively large thickness. Herein, a nanofibrous polyimide (PI) framework enhanced plasticized-PEO solid electrolyte is prepared to realize good mechanical and electrochemical performances. Following the configuration with the PI matrix, this "polymer in polymer" composite electrolyte with a thickness of 17.5 µm exhibits enhanced mechanical strength (13.9 MPa) and outstanding thermal stability. Additionally, it preserves the high ionic conductivity (2.25 × 10-4  S cm-1 , 25 °C). The Li||Li symmetrical battery with the modified electrolyte could achieve a steady Li plating/stripping of more than 500 h, and the critical current density reaches up to 0.6 mA cm-2 at ambient temperature. The LiFePO4 batteries delivery favorable capacity of 132.2 mAh g-1 with capacity retentions of 96.4% and 85.9% after 500 and 1000 cycles at 1 C, respectively. Acceptable cycling performance also could be achieved in LiNi0.5 Co0. 2 Mn0. 3 O2 solid batteries via an inorganic-rich artificial cathode electrolyte interphase.

Supramolecular Polymer Ion Conductor with Weakened Li Ion Solvation Enables Room Temperature All-Solid-State Lithium Metal Batteries

Improved durability, enhanced interfacial stability, and room temperature applicability are desirable properties for all-solid-state lithium metal batteries (ASSLMBs), yet these desired properties are rarely achieved simultaneously. Here, in this work, it is noticed that the huge resistance at Li metal/electrolyte interface dominantly impeded the normal cycling of ASSLMBs especially at around room temperature (<30 °C). Accordingly, a supramolecular polymer ion conductor (SPC) with "weak solvation" of Li+ was prepared. Benefiting from the halogen-bonding interaction between the electron-deficient iodine atom (on 1,4-diiodotetrafluorobenzene) and electron-rich oxygen atoms (on ethylene oxide), the O-Li+ coordination was significantly weakened. Therefore, the SPC achieves rapid Li+ transport with high Li+ transference number, and importantly, derives a unique Li2 O-rich SEI with low interfacial resistance on lithium metal surface, therefore enabling stable cycling of ASSLMBs even down to 10 °C. This work is a new exploration of halogen-bonding chemistry in solid polymer electrolyte and highlights the importance of "weak solvation" of Li+ in the solid-state electrolyte for room temperature ASSLMBs.

Advancements in ToF-SIMS imaging for life sciences

In the last 2 decades, Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) has gained significant prominence as a powerful imaging technique in the field of life sciences. This comprehensive review provides an in-depth overview of recent advancements in ToF-SIMS instrument technology and its applications in metabolomics, lipidomics, and single-cell analysis. We highlight the use of ToF-SIMS imaging for studying lipid distribution, composition, and interactions in cells and tissues, and discuss its application in metabolomics, including the analysis of metabolic pathways. Furthermore, we review recent progress in single-cell analysis using ToF-SIMS, focusing on sample preparation techniques, in situ investigation for subcellular distribution of drugs, and interactions between drug molecules and biological targets. The high spatial resolution and potential for multimodal analysis of ToF-SIMS make it a promising tool for unraveling the complex molecular landscape of biological systems. We also discuss future prospects and potential advancements of ToF-SIMS in the research of life sciences, with the expectation of a significant impact in the field.

In Situ Insight into the Interfacial Dynamics in "Water-in-Salt" Electrolyte-Based Aqueous Zinc Batteries

Water-in-salt (WIS) electrolyte is considered as one of most promising systems for aqueous zinc batteries (AZBs) due to its dendrite-free plating/stripping with nearly 100% Coulombic efficiency. However, the understanding of the interfacial mechanisms remains elusive, which is crucial for further improvements in battery performance. Herein, the interfacial processes of solid electrolyte interphase (SEI) formation and subsequent Zn plating/stripping are monitored by in situ atomic force microscopy and in situ optical microscopy. The live formation of uniform and compact LiF-rich SEI in WIS systems could induce the uniform hexagonal Zn deposition with preferential orientation growth in the (002) crystal plane, showing excellent plating/stripping reversibility. In contrast, the SEI formed in 1 m zinc bis(trifluoromethylsulfonyl)imide (Zn(TFSI)₂ ) is uneven and rich in inert ZnO, adversely triggering the dendrite propagation and successive "dead" Zn accumulation in repeated deposition/dissolution cycles. This work provides an in-depth understanding of the relationship between SEI evolution and Zn-deposited behaviors in AZBs, possibly stimulating more research on rational composition design and structural optimization of solid/liquid interface for advanced rechargeable aqueous multivalent-ion batteries.

In Situ Polymerization Anchoring Effect Enhancing the Structural Stability and Electrochemical Performance of the LiNi0.8Co0.1Mn0.1O2 Cathode Material

LiNi_xCo_yMn_1-x-yO₂ (NCM) is identified as the most classical cathode material on account of its outstanding specific capacity, moderate price, and high safety. However, the surface stability of the high nickel cathode material is poor, which is extremely sensitive to air. Herein, we discover that the electron donor functional groups of organic polymers can form a stable coordination anchoring effect with nickel atoms in the cathode material that can provide an empty orbit through electron transfer, which not only enhances the mutual interface stability between the polymer coating and NCM but also greatly inhibits the decomposition of metal ions in the deintercalation/intercalation process. Density functional theory calculations and first principles reveal that there are coordination bonds and charge transfers between poly(3,4-ethylenedioxythiophene) (PEDOT) and NCM. Consequently, the modified material displayed excellent cyclic stability, with a capacity retention of 91.93% at 1 C after 100 cycles and a rate property of 143.8 mA h g^-1 at 5 C. Moreover, structural analysis indicated that the enhanced cycling stability resulted from the suppression of irreversible phase transitions of PEDOT-coated NCM. This unique mechanism provides a thought for organic coating and surface modification of NCM materials.

Aluminum Impurity from Current Collectors Reactivates Degraded NCM Cathode Materials toward Superior Electrochemical Performance

The huge amount of degraded NCM (LiNi_0.5Co_0.2Mn_0.3O₂) cathode materials from spent lithium-ion batteries is arising as a serious environmental issue as well as a severe waste of metal resources, and therefore, direct recycling of them toward usable electrode materials again is environmentally and economically more attractive in contrast to present metallurgical treatments. In this work, we design a robust two-step method for direct recycling of degraded NCM materials, which uses the aluminum impurity from the attached current collector to supplement the transition metal vacancies for simultaneous elemental compensation and structural restoration. This single-element compensation strategy leads to the regeneration of high-quality NCM material with depressed cation disordering and stabilized layered structure. Moreover, the regenerated NCM material with controllable Al doping delivered an outstanding electrochemical performance; specifically, the capacity (158.6 mAh g^-1), rate capability (91.6 mAh g^-1 at 5 C), and cycling stability (89.6% capacity retention after 200 cycles) of the regenerated NCM material are even comparable with those of fresh materials. The as-established regeneration protocol has its chance in simplifying the industrial recycling process of degraded NCM materials.

An Innovative Insight into Performance Degradation of NCM111 Cathode Induced by Suspension of Operation

The lifespan of lithium-ion batteries varies enormously from fundamental study to practical applications. This big difference has been typically ascribed to the high degree of uncertainty in unpredictable and complicated operation conditions in real-life applications. Here, we report that the pause of the charging-discharging process, which is frequently operated in practice but rarely studied in academics, is an important reason for the performance degradation of the NCM111 cathode. It is found that the pause during cycling could trigger a remarkable drop in capacity, giving rise to ∼30% more capacity decay compared with the continuously cycled sample. In situ synchrotron X-ray diffraction analysis reveals that the harmful H1-H2 phase transition, which typically appears in the initial cycle but disappears in subsequent cycles, is reactivated by the pausing process. The anisotropic lattice strains that occur during the H1-H2 transition result in mechanical fractures that terminate with an inert NiO-type rock-salt phase on the surface of particles. The present study indicates that the discontinuous usage of rechargeable batteries is also a key factor for cycle life, which might provide a distinct perspective on the performance decay in practical applications.

Impact of the Local Environment on Li Ion Transport in Inorganic Components of Solid Electrolyte Interphases

The spontaneously formed passivation layer, the solid electrolyte interphase (SEI) between the electrode and electrolyte, is crucial to the performance and durability of Li ion batteries. However, the Li ion transport mechanism in the major inorganic components of the SEI (Li₂CO₃ and LiF) is still unclear. Particularly, whether introducing an amorphous environment is beneficial for improving the Li ion diffusivity is under debate. Here, we investigate the Li ion diffusion mechanism in amorphous LiF and Li₂CO₃ via machine-learning-potential-assisted molecular dynamics simulations. Our results show that the Li ion diffusivity in LiF at room temperature cannot be accurately captured by the Arrhenius extrapolation from the high temperature (>600 K) diffusivities (difference of ∼2 orders of magnitude). We reveal that the spontaneous formation of Li-F regular tetrahedrons at low temperatures (<500 K) leads to an extremely low Li ion diffusivity, suggesting that designing an amorphous bulk LiF-based SEI cannot help with the Li ion transport. We further show the critical role of Li₂CO₃ in suppressing the Li-F regular tetrahedron formation when these two components of SEIs are mixed. Overall, our work provides atomic insights into the impact of the local environment on Li ion diffusion in the major SEI components and suggests that suppressing the formation of large-sized bulk-phase LiF might be critical to improve battery performance.

Self-Healing of Prussian Blue Analogues with Electrochemically Driven Morphological Rejuvenation

Maintaining the morphology of electrode materials with high invertibility contributes to the prolonged cyclic stability of battery systems. However, the majority of electrode materials tend to degrade during the charge-discharge process owing to the inevitable increase in entropy. Herein, a self-healing strategy is designed to promote morphology rejuvenation in Prussian blue analogue (PBA) cathodes by cobalt doping. Experimental characterization and theoretical calculations demonstrate that a trace amount of cobalt can decelerate the crystallization process and restore the cracked areas to ensure perfect cubic structures of PBA cathodes. The electric field controls the kinetic dynamics, rather than the conventional thermodynamics, to realize the "electrochemically driven dissolution-recrystallization process" for the periodic self-healing phenomenon. The properties of electron transportation and ion diffusion in bulk PBA are also improved by the doping strategy, thus boosting the cyclability with 4000 cycles in a diluent electrolyte. This discovery provides a new paradigm for the construction of self-healing electrodes for cathodes.

Robust Multiscale Electron/Ion Transport and Enhanced Structural Stability in SiOx Semi-Solid Anolytes Enabled by Trifunctional Artificial Interfaces for High-Performance Li-Ion Slurry Flow Batteries

SiO_x suspension is regarded as an attractive anolyte for high-energy-density Li-ion slurry flow batteries. However, the poor electronic conductivity and non-negligible volume variation of SiO_x greatly hinder its practical applications. Herein, these issues are successfully addressed by rationally designing a trifunctional interface with mixed electron/ion and hard/soft modulated properties on SiO_x surface via H-bonding interactions. The interface comprises a lithiated polymer layer (LiPN) interfused with functionalized single-walled carbon nanotubes. Carbon nanotubes work as electrical tentacles to enhance the multiscale electron conduction. The LiPN layer with transferable Li-ions facilitates ion transport. In addition, the LiPN layer employs lithiated rigid polyacrylic acid as a framework to provide mechanical support and soft nafion as a buffer to accommodate volume change, which maintains the structural integrity of SiO_x . Hence, SiO_x @LiPN/S anolytes exhibit significantly improved rate and cycle performances. Specially, the interface enables the anolytes to load more active particles (30 wt%) or less conductive additives (0.4 wt%). The semi-solid pouch cells based on high-active-content anolytes with stable cyclability are first demonstrated and the flow cell using low-conductive-content anolytes displays a high volumetric capacity of 207 Ah L^-1 . This strategy paves a novel approach for optimizing semi-solid electrodes for high-performance Li-ion slurry flow batteries.

A novel design for the combination of electrochemical atomic force microscopy and Raman spectroscopy in reflection mode for in situ study of battery materials

The emergence of functional materials, especially energy materials made up of various structures with different properties, requires the development of complementary or integrated characterization technologies. The combination of atomic force microscopy and Raman spectroscopy (AFM-Raman) offers a powerful technique for the in situ characterization of physical properties (AFM) and chemical composition (Raman) of materials simultaneously. To further extend the potential application in the battery's field, we here present an electrochemical AFM-Raman (EC-AFM-Raman) in the reflection mode, developed by designing a novel structure including water-immersion objective lens-based optics for high-sensitivity Raman excitation/collection, optical level detection for AFM imaging in the solution, and a dual-cell for electrochemical reaction. EC-AFM imaging and Raman measurement can be realized simultaneously. Dynamic morphologic evolution and phase transition of the LiMn₂O₄ particles during cyclic voltammetry measurement were successfully observed. This technique will provide the possibility of probing physicochemical phenomena of the battery materials and other surface/interface processes such as the formation of the solid electrolyte interphase layer.

Lithium Bromide-Induced Organic-Rich Cathode/Electrolyte Interphase for High-Voltage and Flame-Retardant All-Solid-State Lithium Batteries

Poly(ethylene oxide) (PEO)-based solid electrolyte suffers from limited anodic stability and an intrinsic flammable issue, hindering the achievement of high energy density and safe all-solid-state lithium batteries. Herein, we surprisingly found out that a bromine-rich additive, decabromodiphenyl ethane (DBDPE), could be preferably oxidized at an elevated voltage and decompose to lithium bromide at an elevated potential followed by inducing an organic-rich cathode/electrolyte interphase (CEI) on NCM811 surface, enabling both high-voltage resistance (up to 4.5 V) and flame-retardancy for the PEO-based electrolyte. On the basis of this novel solid electrolyte, all-solid-state Li/NCM811 batteries deliver an average reversible capacity of 151.4 mAh g^-1 over the first 150 cycles with high capacity retention (83.0%) and high average Coulombic efficiency (99.7%) even at a 4.5 V cutoff voltage with a unprecedented flame-retardant properties. In view of these exploration, our studies revealed the critical role of LiBr in inducing an organic-rich thin and uniform CEI passivating layer with enhanced lithium ion surface diffusion and high-voltage resistant properties, which provides a new protocol for the further design of a high-voltage PEO-based all-solid-state electrolyte.

Organo-Soluble Decanoic Acid-Modified Ni-Rich Cathode Material LiNi0.90Co0.07Mn0.03O2 for Lithium-Ion Batteries

Ni-rich layered oxides as cathode materials deliver a higher capacity than those used currently, in hopes of improving the energy density of Li-ion batteries. However, the surface residual alkali and the interfacial parasitic reactions caused by the rich nickel bring a series of problems such as surface slurrying, structure deterioration, mechanical fracture, and capacity decay. Herein, different from the common surface coating strategies with inorganics, an organo-soluble acid modification approach is proposed to meet the challenges. For LiNi_0.90Co_0.07Mn_0.03O₂ (NCM90), decanoic acid can react with the residual lithium salts on the surface to form an organic lithium salt-dominant modification layer. During cycling, an organic lithium-involved cathode/electrolyte interface (CEI) layer is rapidly formed. Specially, the solubility of decanoic acid in the organic electrolyte makes the CEI layer keep strong interaction with NCM90, thin but effective. Consequently, the modified NCM90 exhibits notable performances in terms of structural stability, mechanical integrity, and capacity retention.

An Active-Oxygen-Scavenging Oriented Cathode-Electrolyte-Interphase for Long-Life Lithium-Rich Cathode Materials

Lithium-rich layered oxides with high energy density are promising cathode materials, thus having attracted a large number of researchers. However, the materials cannot be commercialized for application so far. The crucial problem is the releasing of lattice oxygen at high voltage and resulting consequence, such as decomposition of electrolyte, irreversible phase transition of crystal structure, capacity degradation, and voltage decay. Therefore, capturing active-oxygen and further constructing a cathode-electrolyte-interface (CEI) protective layer via the scavenging effects should be a fundamental step to solve these issues. Herein, β-carotene with antioxidant properties is used as a scavenging molecule to achieve this goal. The control of active oxygen species effectively alleviates the decomposition of carbonate electrolyte under high voltage. The introduction of β-carotene additives can also be adjusted in situ to generate a customized CEI film, which is a double-layer structure with external organic components and internal inorganic components. Moreover, the β-carotene-containing electrolyte system exhibits better thermal stability. Benefited from these, Lithium-rich cathode of β-carotene-containing electrolyte shows outstanding long-life cycle stability, with 93.4% capacity retention rate after 200 cycles at 1 C; this electrochemical stability is superior to other electrolyte additive systems reported at present.

Cooperative Shielding of Bi-Electrodes via In Situ Amorphous Electrode-Electrolyte Interphases for Practical High-Energy Lithium-Metal Batteries

Solid-state Li-metal batteries offer a great opportunity for high-security and high-energy-density energy storage systems. However, redundant interfacial modification layers, intended to lead to an overall satisfactory interfacial stability, dramatically debase the actual energy density. Herein, a dual-interface amorphous cathode electrolyte interphase/solid electrolyte interphase CEI/SEI protection (DACP) strategy is proposed to conquer the main challenges of electrochemical side reactions and Li dendrites in hybrid solid-liquid batteries without sacrificing energy density via LiDFOB and LiBF₄ in situ synergistic conversion. The amorphous CEI/SEI products have an ultralow mass proportion and act as a dynamic shield to cooperatively enforce dual electrodes with a well-preserved structure. Thus, this in situ DACP layer subtly reconciles multiple interfacial compatibilities and a high energy density, endowing the hybrid solid-liquid Li-metal battery with a sustainably brilliant cycling stability even at practical conditions, including high cathode loading, high voltage (4.5 V), and high temperature (45 °C) conditions, and enables a high-energy-density (456 Wh kg^-1) pouch cell (11.2 Ah, 5 mA h cm^-2) with a lean electrolyte (0.92 g Ah^-1, containing solid and liquid phases). The compatible modification strategy points out a promising approach for the design of practical interfaces in future solid-state battery systems.

In Situ Characterization of Over-Lithiation of Organosulfide-Based Lithium Metal Anodes

Over-lithiated organosulfides, such as sulfurized polyacrylonitrile (SPAN), are promising candidates of lithium metal anode (LMA) protection since they could form robust solid electrolyte interphases (SEIs), which is the key toward stable lithium metal batteries. So far, the mechanism of over-lithiation and evolution of the electrode surface is poorly understood. Herein, several in situ techniques were employed to study the over-lithiation process in SPAN, including in situ Raman spectroscopy to reveal the chemical transformation and in situ electrochemical atomic force microscopy (EC-AFM) to visualize interfacial evolution. The results undoubtedly prove the breaking of the C-S bond and formation of the C-Li bond during the over-lithiation process. The nucleophilic C-Li could further trigger the decomposition of the electrolyte to form an inorganic-organic hybrid SEI on the surface of SPAN, which allows uniform Li deposition and significantly improves the cycle stability of LMAs, as supported by the in situ EC-AFM characterization as well as a series of full cell tests. New insights into the over-lithiation mechanism of SPAN should facilitate the design of organosulfides to construct stable lithium metal anodes.