Weak Bonds in a Biomimetic Adhesive Enhance Toughness and Performance

P(MMA-co-MAA)/cellulose nanofibers composites: Effect of hydrogen bonds on molecular mobility

Cellulose nanofibers (CNFs) nanocomposites were prepared using poly(methylmethacrylate-co-methacrylic acid) (PMMA-co-MAA) to investigate the macromolecular mobility within the composite, with particular focus on the effect of H-bonding. Dynamic mechanical analysis (DMA) and broadband dielectric spectroscopy (BDS) were used to fully characterize the molecular mobility for which the effect of the introduction of H-bond forming moieties and the addition of CNFs (5 and 15 wt%) were assessed. Despite similar Tg values (determined by Differential Scanning Calorimetry), a deeper analysis of the relaxation times associated with the α-relaxation evidenced a significant effect induced by CNFs, which is in fact slowing down the macromolecular relaxation processes. The activation energy of the β-relaxation remained unchanged despite the introduction of MAA units in the main chain and the successive addition of CNFs. However, the latter led to the appearance at low frequencies of a new β'-relaxation correlated with the interactions between the CNF surface -OH groups and the -COOH groups of the matrix. The γ-relaxation showed a 45 % increase in activation energy from PMMA to PMMA-co-MAA + CNF nanocomposites regardless of the CNF content, due to the possibility of CNFs to interact and hinder the motion of the main chain methyl groups in α position.

A tough, strong, and fast-curing phenolic resin enabled by dopamine-grafted chitosan and polyethyleneimine-functionalized graphene

Phenolic resins are widely used for outdoor and structural wood-based panels; however, they are challenged by high curing temperatures, low curing rates, and high brittleness. Inspired by lobster epidermis hardening, a tough, strong, and fast-curing phenolic resin (named DCS/PG/PF) was proposed herein. In this approach, dopamine-grafted chitosan (DCS) and polyethyleneimine-functionalized graphene (PEI@G) were incorporated into neat phenol formaldehyde (PF) resin. The gel time and maximum curing temperature of DCS/PG/PF resin were considerably reduced from 445 s and 147.8 °C for the neat PF resin to 317 s and 127.8 °C, respectively. This was attributed to the oxidative crosslinking of catechol moieties in DCS and amino groups in PEI@G within the naturally alkaline environment of phenolic resins in addition to the high reactivity between catechol moieties and PF chains as well as between amino and PF chains. The prepared resin demonstrated a dry bonding strength of 2.56 MPa, wet bonding strength of 1.81 MPa, and debonding work of 0.714 J, exhibiting a considerable increase of 16.9 %, 52.1 %, and 95.1 %, respectively, compared with those of the PF resin. These improvements were attributed to the dense organic-inorganic hybrid crosslinking network formed in the DCS/PG/PF. Furthermore, the DCS/PG/PF resin exhibited enhanced thermal stability.

Mechanically Interlocked [an]Daisy Chain Adhesives with Simultaneously Enhanced Interfacial Adhesion and Cohesion

Adhesives have been widely used to splice and repair materials to meet practical needs of humanity for thousands of years. However, developing robust adhesives with balanced adhesive and cohesive properties still remains a challenging task. Herein, we report the design and preparation of a robust mechanically interlocked [an]daisy chain network (DCMIN) adhesive by orthogonal integration of mechanical bonds and 2-ureido-4[1H]-pyrimidone (UPy) H-bonding in a single system. Specifically, the UPy moiety plays a dual role: it allows the formation of a cross-linked network and engages in multivalent interactions with the substrate for strong interfacial bonding. The mechanically interlocked [an]daisy chain, serving as the polymeric backbone of the adhesive, is able to effectively alleviate applied stress and uphold network integrity through synergistic intramolecular motions, and thus significantly improves the cohesive performance. Comparative analysis with the control made of the same quadruple H-bonding network but with non-interlocked [an]daisy chain backbones demonstrates that our DCMIN possesses superior adhesion properties over a wide temperature range. These findings not only contribute to a deep understanding of the structure-property relationship between microscopic mechanical bond motions and macroscopic adhesive properties but also provide a valuable guide for optimizing design principles of robust adhesives.

Salicylhydroxamic acid containing structural adhesive

The feasibility of utilizing salicylhydroxamic acid (SHAM) as a new adhesive molecule for designing structural adhesives is investigated in this study. SHAM-containing polymers were prepared with a hydroxyethyl methacrylate (HEMA) or methoxyethyl acrylate (MEA) backbone and mixed with polyvinylidene fluoride (PVDF). PVDF was included to increase the cohesive property of the adhesive through hydrogen bond (H-bond) formation with the adhesive polymers. SHAM-containing adhesive demonstrated lap shear adhesion strength (S adh) greater than 0.9 MPa to glass, metal, and polymeric surfaces. Adhesive formulations with elevated SHAM-content also demonstrated increased adhesive properties with S adh values reaching as high as 4.8 MPa. Due to the physically crosslinked nature of these adhesives, formulations with extensive H-bonding resulted in strong adhesion and stability. HEMA consists of a terminal hydroxyl group with both H-bond donor and acceptor, which enabled HEMA-containing adhesives to demonstrate strong adhesion even without PVDF. On the other hand, MEA contains a methoxy group that lacks H-bond donors for forming H-bonding and MEA-containing adhesives required PVDF to provide H-bond acceptors to increase its cohesive property. An aging study was performed on the bonded joints. While the adhesive joints did not demonstrate any reduction in S adh values over 25 days when incubated in a dry condition, S adh values decreased by 80% over 48 h when incubated in water. This is potentially due to the hydrophilic and physically crosslinked nature of the adhesive. Nevertheless, the SHAM-containing adhesive outperformed a catechol-containing adhesive and epoxy glue and is a promising new adhesive molecule for designing structural adhesives.

Clicked into Place: Biomimetic Copolymer Adhesive for Covalent Conjugation of Functionalities

Polydopamines (PDA) are a popular class of materials and promising candidates as adhesives for new fastening techniques. PDA layers can be formed on a wide range of substrates in various environments. Here, we present a novel method for functionalizing PDA-based copolymer films by using click chemistry. These copolymers adhere strongly to various surfaces and simultaneously have active groups that allow the attachment of functional groups. We discuss the coupling of two types of chitosan and a rhodamine B dye molecule to the alkyne groups of the copolymers by employing click reactions. Azidopropyl methacrylate (AzMA), methyl methacrylate (MMA), and dopamine methacrylamide (DOMA) are copolymerized and codeposited with (3-aminopropyl)triethoxysilane on silicon wafers, polyethylene (PE), and polytetrafluoroethylene (PTFE). AzMA provides the surfaces with azides for use in click reactions, MMA functions to control the polymer as a nonfunctional diluent, whereas DOMA provides adhesion, as well as cross-linking groups. After codeposition, the dyes are grafted to the copolymer to illustrate the ability of the films to link functional groups covalently. Fourier transform infrared spectroscopy confirms the successful click reaction in solution, and atomic force microscopy shows the surface morphologies following grafting. Fluorescence microscopy provides evidence of successful grafting. As an example of a possible application, layers exhibiting antifouling properties are prepared. Chitosan grafted to PE is tested for antifouling performance. These functionalized layers show nonspecific inhibition of protein adsorption. We find that chitosan can lower the adsorption of fluorescein-labeled bovine serum albumin (BSA) protein by more than 90% for the best performing fluorescein-labeled BSA protein and by more than 90% for the best-performing layer. These results demonstrate the viability of our PDA-based copolymers for surface functionalization through click chemistry grafting at challenging adhesion to surfaces.

Branched Oligomer-Based Reversible Adhesives Enabled by Controllable Self-Aggregation

Supramolecular adhesion material systems based on small molecules have shown great potential to unite the great contradiction between strong adhesion and reversibility. However, these material systems suffer from low adhesion strength/narrow adhesion span, limited designability, and single interaction due to fewer covalent bond content and action sites in small molecules. Herein, an ultrahigh-strength and large-span reversible adhesive enabled by a branched oligomer controllable self-aggregation strategy is developed. The dense covalent bonds present in the branched oligomers greatly enhance adhesion strength without compromising reversibility. The resulting adhesive exhibits a large-span reversible adhesion of ≈140 times, switching between ultra-strong and tough adhesion strength (5.58 MPa and 5093.92 N m-1) and ultralow adhesion (0.04 MPa and 87.656 N m-1) with alternating temperature. Moreover, reversible dynamic double cross-linking endows the adhesive with stable reversible adhesion transitions even after 100 cycles. This reversible adhesion property can also be remotely controlled via a voltage of 8 V, with a loading voltage duration of 45 s. This work paves the way for the design of reversible adhesives with long-span outstanding properties using covalent polymers and offers a pathway for the rational design of high-performance adhesives featuring both robust toughness and exceptional reversibility.

Unveiling the Architectural Impact on the Salt-Tunable Adhesion Performance and Toughness of Polyzwitterions

Developing tough adhesives with superior strength and ductility is challenging yet highly sought-after. In this work, we address a strategic approach to achieving diverse toughness and performance by meticulously harnessing weak electrostatic interactions. Two polyzwitterions (PZIs), derived from sulfobetaine methacrylate (SBMA), of different topologies: bottlebrush (BB-PSBMA) and linear (L-PSBMA), were designed. BB-PSBMA was synthesized using a rational "grafting-from" strategy, while L-PSBMA was prepared via atom transfer radical polymerization. Despite their architectural disparities, both PZIs demonstrated a comparable substantial lap-shear adhesion strength of ∼0.4 MPa. Intriguingly, the introduction of NaCl during adhesive preparation revealed contrasting adhesion behaviors. BB-PSBMA transitioned from a strong-brittle to strong-ductile adhesive upon the addition of 70 mM NaCl, evidenced by a 77.4% increase in the work of debonding, i.e., toughness. Further increases in NaCl concentration continued to impart the ductile properties to BB-PSBMA. Conversely, L-PSBMA adhesive predominantly transformed from strong-brittle to ductile regardless of the salt content. We propose a synergistic mechanism involving viscosity-governed optimal adhesion-cohesion balance and mechanical energy dissipation through sacrificial electrostatic association to elucidate the strong and ductile nature of the BB-PSBMA adhesive at 70 mM NaCl. Our findings emphasize the significance of precise control over architecture and salt concentration is necessary in constructing adhesives with enhanced toughness and performance.

Adhesive Zwitterionic Poly(ionic liquid) with Unprecedented Organic Solvent Resistance

The resistance of adhesives to organic solvents is of paramount importance in diverse industries. Unfortunately, many currently available adhesives exhibit either weak intermolecular chain interactions, resulting in insufficient resistance to organic solvents, or possess a permanent covalent crosslinked network, impeding recyclability. This study introduces an innovative approach to address this challenge by formulating zwitterionic poly(ionic liquid) (ZPIL) derivatives with robust dipole-dipole interactions, incorporating sulfonic anions and imidazolium cations. Due to its unique dynamic and electrostatic self-crosslinking structure, the ZPIL exhibits significant adhesion to various substrates and demonstrates excellent recyclability even after multiple adhesion tests. Significantly, ZPIL exhibits exceptional adhesion stability across diverse nonpolar and polar organic solvents, including ionic liquids, distinguishing itself from nonionic polymers and conventional poly(ionic liquid)s. Its adhesive performance remains minimally affected even after prolonged exposure to soaking conditions. The study presents a promising solution for the design of highly organic solvent-resistant materials for plastics, coatings, and adhesives.

Silicone Bioadhesive with Shear-Stiffening Effect: Rate-Responsive Adhesion Behavior and Wound Dressing Application

Stimuli-responsive adhesives with on-demand adhesion capabilities are highly advantageous for facilitating wound healing. However, the triggering conditions of stimuli-responsive adhesives are cumbersome, even though some of them are detrimental to the adhesive and adjacent natural tissues. Herein, a novel stimuli-responsive adhesive called shear-stiffening adhesive (SSA) has been created by constructing a poly(diborosiloxane)-based silicone network for the first time, and SSA exhibits a rate-responsive adhesion behavior. Furthermore, we introduced bactericidal factors (PVP-I) into SSA and applied it as a wound dressing to promote the healing of infected wounds. Impressively, the wound dressing not only has excellent biocompatibility and long-term antibacterial properties but also performs well in accelerating wound healing. Therefore, this study provides a new strategy for the synthesis of intelligent adhesives with force rate response, which simplifies the triggering conditions by the force rate. Thus, SSA has great potential to be applied in wound management as an intelligent bioadhesive with on-demand adhesion performance.

Glued-bamboo composite based on a highly cross-linked cellulose-based adhesive and an epoxy functionalized bamboo surface

Bamboo, as a renewable bioresource, exhibits advantages of fast growth cycle and high strength. Bamboo-based composite materials are a promising alternative to load-bearing structural materials. It is urgent to develop high-performance glued-bamboo composite materials. This study focused on the chemical bonding interface to achieve high bonding strength and water resistance between bamboo and dialdehyde cellulose-polyamine (DAC-PA4N) adhesive by activating the bamboo surface. The bamboo surface was initially modified in a directional manner to create an epoxy-bamboo interface using GPTES. The epoxy groups on the interface were then chemically crosslinked with the amino groups of the DAC-PA4N adhesive, forming covalent bonds within the adhesive layer. The results demonstrated that the hot water strength of the modified bamboo was improved by 75.8 % (from 5.17 to 9.09 MPa), and the boiling water strength was enhanced by 232 % (from 2.10 to 6.99 MPa). The bonding and flexural properties of this work are comparable to those of commercial phenolic resin. The activation modification of the bamboo surface offers a novel approach to the development of low-carbon, environmentally friendly, and sustainable bamboo engineering composites.

Concentration-induced spontaneous polymerization of protic ionic liquids for efficient in situ adhesion

The advancement of contemporary adhesives is often limited by the balancing act between cohesion and interfacial adhesion strength. This study explores an approach to overcome this trade-off by utilizing the spontaneous polymerization of a protic ionic liquid-based monomer obtained through the neutralization of 2-acrylamide-2-methyl propane sulfonic acid and hydroxylamine. The initiator-free polymerization process is carried out through a gradual increase in monomer concentration in aqueous solutions caused by solvent evaporation upon heating, which results in the in-situ formation of a tough and thin adhesive layer with a highly entangled polymeric network and an intimate interface contact between the adhesive and substrate. The abundance of internal and external non-covalent interactions also contributes to both cohesion and interfacial adhesion. Consequently, the produced protic poly(ionic liquid)s exhibit considerable adhesion strength on a variety of substrates. This method also allows for the creation of advanced adhesive composites with electrical conductivity or visualized sensing functionality by incorporating commercially available fillers into the ionic liquid adhesive. This study provides a strategy for creating high-performance ionic liquid-based adhesives and highlights the importance of in-situ polymerization for constructing adhesive composites.

Converting inorganic sulfur into degradable thermoplastics and adhesives by copolymerization with cyclic disulfides

Converting elementary sulfur into sulfur-rich polymers provides a sustainable strategy to replace fossil-fuel-based plastics. However, the low ring strain of eight-membered rings, i.e., S8 monomers, compromises their ring-opening polymerization (ROP) due to lack of an enthalpic driving force and as a consequence, poly(sulfur) is inherently unstable. Here we report that copolymerization with cyclic disulfides, e.g., 1,2-dithiolanes, can enable a simple and energy-saving way to convert elementary sulfur into sulfur-rich thermoplastics. The key strategy is to combine two types of ROP-both mediated by disulfide bond exchange-to tackle the thermodynamic instability of poly(sulfur). Meanwhile, the readily modifiable sidechain of the cyclic disulfides provides chemical space to engineer the mechanical properties and dynamic functions over a large range, e.g., self-repairing ability and degradability. Thus, this simple and robust system is expected to be a starting point for the organic transformation of inorganic sulfur toward sulfur-rich functional and green plastics.

Iterative SuFEx approach for sequence-regulated oligosulfates and its extension to periodic copolymers

The synthesis of sequence-regulated oligosulfates has not yet been established due to the difficulties in precise reactivity control. In this work, we report an example of a multi-directional divergent iterative method to furnish oligosulfates based on a chain homologation approach, in which the fluorosulfate unit is regenerated. The oligosulfate sequences are determined by high resolution mass spectrometry of the hydrolyzed fragments, and polysulfate periodic copolymers are synthesized by using oligomeric bisfluorosulfates in a bi-directional fashion. The synthetic utility of this iterative ligation is demonstrated by preparing crosslinked network polymers as synthetic adhesive materials.

Desirable Strong and Tough Adhesive Inspired by Dragonfly Wings and Plant Cell Walls

The production of wood-based panels has a significant demand for mechanically strong and flexible biomass adhesives, serving as alternatives to nonrenewable and toxic formaldehyde-based adhesives. Nonetheless, plywood usually exhibits brittle fracture due to the inherent trade-off between rigidity and toughness, and it is susceptible to damage and deformation defects in production applications. Herein, inspired by the microstructure of dragonfly wings and the cross-linking structure of plant cell walls, a soybean meal (SM) adhesive with great strength and toughness was developed. The strategy was combined with a multiple assembly system based on the tannic acid (TA) stripping/modification of molybdenum disulfide (MoS2@TA) hybrids, phenylboronic acid/quaternary ammonium doubly functionalized chitosan (QCP), and SM. Motivated by the microstructure of dragonfly wings, MoS2@TA was tightly bonded with the SM framework through Schiff base and strong hydrogen bonding to dissipate stress energy through crack deflection, bridging, and immobilization. QCP imitated borate chemistry in plant cell walls to optimize interfacial interactions within the adhesive by borate ester bonds, boron-nitrogen coordination bonds, and electrostatic interactions and dissipate energy through sacrificial bonding. The shear strength and fracture toughness of the SM/QCP/MoS2@TA adhesive were 1.58 MPa and 0.87 J, respectively, which were 409.7% and 866.7% higher than those of the pure SM adhesive. In addition, MoS2@TA and QCP gave the adhesive good mildew resistance, durability, weatherability, and fire resistance. This bioinspired design strategy offers a viable and sustainable approach for creating multifunctional strong and tough biobased materials.

High-Toughness CO2-Sourced Ionic Polyurea Adhesives

Polyurea (PUa) adhesives are renowned for their exceptional adhesion to diverse substrates even in harsh environments. However, the presence of quadruple bidentate intermolecular hydrogen bonds in the polymer chains creates a trade-off between cohesive energy and interfacial adhesive energy. To overcome this challenge, a series of CO2-sourced ionic PUa adhesives with ultratough adhesion to various substrates are developed. The incorporated ionic segments within the adhesive serve to partially mitigate the intermolecular hydrogen bonding interactions while conferring unique electrostatic interactions, leading to both high cohesive energy and interfacial adhesive energy. The maximum adhesive strength of 10.9 MPa can be attained by ionizing the CO2-sourced PUa using bromopropane and subsequently exchanging the anion with lithium bis(trifluoromethylsulfonyl)imide. Additionally, these ionic PUa adhesives demonstrate several desirable properties such as low-temperature stability (-80 °C), resistance to organic solvents and water, high flame retardancy, antibacterial activity, and UV-fluorescence, thereby expanding their potential applications. This study presents a general and effective approach for designing high-strength adhesives suitable for a wide array of uses.

Solvent-Resistant Adhesive Gel with Thermal Post-Tunability

Adhesives have received extensive attention in flexible bioelectronics, wearable electronic medical devices, and biofuel cells. However, it is a challenge to achieve late regulation of performance once polymer-based gels are formed. Here, a double-network organogel composed of a hydrophilic and hydrophobic polymer network and a polyamide acid network was successfully prepared. In diverse liquid environments (including isopropyl alcohol, glycerol, epichlorohydrin, n-propanol, dichloromethane, triethanolamine, ethanol absolute, hydrogen peroxide, and ethyl acetate), the organogel adhesive demonstrated remarkable properties. It exhibits a strong tensile strength of 200 kPa, a high fracture strain reaching 560%, and an impressive adhesion strength of 38 kPa. In addition, the organogel demonstrates exceptional adhesive properties toward polytetrafluoroethylene, plastics, metals, rubber, and glass. Note that the organogel could also regulate adhesive and tough performance by thermally triggering a cyclization reaction even after the organogel has been formed. The strategy provides a new idea for designing soft materials with post-tunability.

Solvent-Exchange Triggered Solidification of Peptide/POM Coacervates for Enhancing the On-Site Underwater Adhesion

Peptide-based biomimetic underwater adhesives are emerging candidates for understanding the adhesion mechanism of natural proteins secreted by sessile organisms. However, there is a grand challenge in the functional recapitulation of the on-site interfacial spreading, adhesion and spontaneous solidification of native proteins in water using peptide adhesives without applied compressing pressure. Here, a solvent-exchange strategy was utilized to exert the underwater injection, on-site spreading, adhesion and sequential solidification of a series of peptide/polyoxometalate coacervates. The coacervates were first prepared in a mixed solution of water and organic solvents by rationally suppressing the non-covalent interactions. After switching to a water environment, the solvent exchange between bulk water and the organic solvent embedded in the matrix of the peptide/polyoxometalate coacervates recovered the hydrophobic effect by increasing the dielectric constant, resulting in a phase transition from soft coacervates to hard solid with enhanced bulk cohesion and thus compelling underwater adhesive performance. The key to this approach is the introduction of suitable organic solvents, which facilitate the control of the intermolecular interactions and the cross-linking density of the peptide/polyoxometalate adhesives in the course of solidification under the water line. The solvent-exchange method displays fascinating universality and compatibility with different peptide segments.

Research on topological effect of natural small molecule and high-performance antibacterial air filtration application by electrospinning

The application of natural small molecule (NSM) in electrospun fibers is the key to achieving powerful functionality and sustainable development. However, the lack of understanding regarding the mechanism for loading NSM hinders the advancement of high-performance functional fibers. This work clarified the loading mechanism of NSM in polymer solution by comparing the different behaviors of curcumin (Cur), phloretin (PL), and tea polyphenols (TP) blended ethyl cellulose (EC) solutions. We found that TP may lead to the folding of polymer chains due to its strongest hydrogen bond, which in turn promoted the dispersion of TP along the polymer chain. Therefore, TP could achieve good electrospinnability at the highest loading capacity (16 times the Cur and 4 times the PL). Finally, chitosan was introduced into EC/TP to prepare tree-like nanofibers, achieving high-performance antibacterial air filtration. The filtration efficiency for 0.3 μm NaCl particles, pressure drop, and quality factor were 99.991 %, 85.5 Pa, and 0.1089 Pa-1, respectively. The bacteriostatic rates against Escherichia coli and Staphylococcus aureus were all 99.99 %. This work will promote the application of NSM and the developments of multifunctional electrospun fibers and high-performance air filters.

Elastic Network of Droplets for Underwater Adhesives

Functionality in biological materials arises from complex hierarchical structures formed through self-assembly processes. Here, we report a kinetically trapped self-assembly of an elastic network of liquid droplets and its utility for tough and fast-acting underwater adhesives. This complex structure was made from a one-pot mixture of scalable small-molecule precursors. Liquid-liquid phase separation accompanied by silanol hydrolysis, condensation, and zwitterionic self-association yields a viscoelastic solid with interconnected liquid droplets. These hierarchical microstructures increase toughness and enable underwater adhesion for a range of substrates, offering a platform for robust adhesives for rapid underwater repair or emergency wound care.

Oyster-inspired carbon dots-functionalized silica and dialdehyde chitosan to fabricate a soy protein adhesive with high strength, mildew resistance, and long-term water resistance

Developing multifunctional adhesives with exceptional cold-pressing strength, water resistance, toughness, and mildew resistance remains challenging. Herein, inspired by oysters, a multifunctional organic-inorganic hybrid soybean meal (SM)-based adhesive was fabricated by incorporating amino-modified carbon dots functionalized silica nanoparticles (CDs@SiO2) and dialdehyde chitosan (DCS) into SM matrix. DCS effectively enhanced the interface interactions of organic-inorganic phases and the rigid nanofillers CDs@SiO2 uniformly dispersed in the SM matrix, which provided energy dissipation to improve the adhesive's toughness. Owing to the stiff skeleton structure and enhanced crosslinking density, the crosslinker-modified SM (MSM)/DCS/CDs@SiO2-2 wood adhesive exhibited outstanding cold-pressing strength (0.74 MPa), wet shear strength (1.36 MPa), and long-term water resistance (49 d). Additionally, the resultant adhesive showed superior antimildew and antibacterial properties benefiting from the introduction of DCS. Intriguingly, the fluorescent properties endowed by carbon dots further broadened the application of adhesives for realizing security testing. This study opens a new pathway for the synthesis of multifunctional biomass adhesives in industrial and household applications.

A strain-reinforcing elastomer adhesive with superior adhesive strength and toughness

Strong and ductile adhesives often undergo both interfacial and cohesive failure during the debonding process. Herein, we report a rare self-reinforcing polyurethane adhesive that shows the different phenomenon of only interfacial failure yet still exhibiting superior adhesive strength and toughness. It is synthesized by designing a hanging adhesive moiety, hierarchical H-bond moieties, and a crystallizable soft segment into one macromolecular polyurethane. The former hanging adhesive moiety allows the hot-melt adhesive to effectively associate with the target substrate, providing sufficient adhesion energy; the latter hierarchical H-bond moieties and a crystallizable soft segment cooperate to enable the adhesive to undergo large lap-shear deformations through sacrificing weak bonds and mechano-responsive strength through the fundamental mechanism of strain-induced crystallization. As a result, this polyurethane adhesive can keep itself intact during the debonding process while still withstanding a high lap-shear strength and dissipating tremendous stress energy. Its adhesive strength and work of debonding are as high as 11.37 MPa and 10.32 kN m-1, respectively, outperforming most reported tough adhesives. This self-reinforcing adhesive is regarded as a new member of the family of strong and ductile adhesives, which will provide innovative chemical and structural inspirations for future conveniently detachable yet high-performance adhesives.

Peptide/glycyrrhizic acid supramolecular polymer: An emerging medical adhesive for dural sealing and repairing

Medical adhesives have emerged as potential materials for sealing, hemostasis and wound repairing in modern clinical surgery. However, most of existing medical adhesives are still far away from the clinical requirements for simultaneously meeting desirable tissue adhesion, safety, biodegradability, anti-swelling property, and convenient operability. Here, we present an entirely new kind of peptide-based underwater adhesives, which are constructed via cross-linked supramolecular copolymerization between cationic short peptides and glycyrrhizic acid (GA) in an aqueous solution. We revealed the unique molecular mechanism of the peptide/GA supramolecular polymers and underlined the importance of arginine residues in the enhancement of the bulk cohesion of the peptide/GA adhesive. We thus concluded a design guideline that the peptide sequence has to be encoded with multiple arginine termini and hydrophobic residues. The resulting adhesives exhibited effective tissue adhesion, robust cohesion, low cell cytotoxicity, acceptable hemocompatibility, inappreciable inflammation response, appropriate biodegradability, and excellent anti-swelling property. More attractively, the dried peptide/GA powder was able to rapidly self-gel into adhesives by absorbing water, suggesting conveniently clinical operability. Animal experiments showed that the peptide/GA supramolecular polymers could be utilized as reliable medical adhesives for dural sealing and repairing.

Sustainably sourced components to generate high-strength adhesives

Nearly all adhesives1,2 are derived from petroleum, create permanent bonds3, frustrate materials separation for recycling4,5 and prevent degradation in landfills. When trying to shift from petroleum feedstocks to a sustainable materials ecosystem, available options suffer from low performance, high cost or lack of availability at the required scales. Here we present a sustainably sourced adhesive system, made from epoxidized soy oil, malic acid and tannic acid, with performance comparable to that of current industrial products. Joints can be cured under conditions ranging from use of a hair dryer for 5 min to an oven at 180 °C for 24 h. Adhesion between metal substrates up to around 18 MPa is achieved, and, in the best cases, performance exceeds that of a classic epoxy, the strongest modern adhesive. All components are biomass derived, low cost and already available in large quantities. Manufacturing at scale can be a simple matter of mixing and heating, suggesting that this new adhesive may contribute towards the sustainable bonding of materials.

Fabrication of High-Performance Natural Rubber Composites with Enhanced Filler-Rubber Interactions by Stearic Acid-Modified Diatomaceous Earth and Carbon Nanotubes for Mechanical and Energy Harvesting Applications

Mechanical robustness and high energy efficiency of composite materials are immensely important in modern stretchable, self-powered electronic devices. However, the availability of these materials and their toxicities are challenging factors. This paper presents the mechanical and energy-harvesting performances of low-cost natural rubber composites made of stearic acid-modified diatomaceous earth (mDE) and carbon nanotubes (CNTs). The obtained mechanical properties were significantly better than those of unfilled rubber. Compared to pristine diatomaceous earth, mDE has higher reinforcing efficiencies in terms of mechanical properties because of the effective chemical surface modification by stearic acid and enhanced filler-rubber interactions. The addition of a small amount of CNT as a component in the hybrid filler systems not only improves the mechanical properties but also improves the electrical properties of the rubber composites and has electromechanical sensitivity. For example, the fracture toughness of unfilled rubber (9.74 MJ/m3) can be enhanced by approximately 484% in a composite (56.86 MJ/m3) with 40 phr (per hundred grams of rubber) hybrid filler, whereas the composite showed electrical conductivity. At a similar mechanical load, the energy-harvesting efficiency of the composite containing 57 phr mDE and 3 phr CNT hybrid filler was nearly double that of the only 3 phr CNT-containing composite. The higher energy-harvesting efficiency of the mDE-filled conductive composites may be due to their increased dielectric behaviour. Because of their bio-based materials, rubber composites made by mDE can be considered eco-friendly composites for mechanical and energy harvesting applications and suitable electronic health monitoring devices.

Suppression of Dendrites by a Self-Healing Elastic Interface in a Sodium Metal Battery

The safety issues caused by sodium dendrites limit the widespread application of sodium metal batteries. Herein, a self-healing polymer electrolyte (SPE) is prepared by immersing the self-healing polymer in a liquid electrolyte. Benefiting from the self-healing properties, elastic interface, and dense nonporous structure of the SPE, the fabricated NaK|MC SPE|NaK symmetric battery presents a long battery life (∼590 h) and low polarization voltage (192 mV). Moreover, the PTCDA|MC SPE|NaK full cell also delivers stable long cycles and outstanding rate performance.

Crack deflection in laminates with graded stiffness-lessons from biology

A crack propagating through a laminate can cause severe structural failure, which may be avoided by deflecting or arresting the crack before it deepens. Inspired by the biology of the scorpion exoskeleton, this study shows how crack deflection can be achieved by gradually varying the stiffness and thickness of the laminate layers. A new generalized multi-layer, multi-material analytical model is proposed, using linear elastic fracture mechanics. The condition for deflection is modeled by comparing the applied stress causing a cohesive failure, resulting in crack propagation, to that causing an adhesive failure, resulting in delamination between layers. We show that a crack propagating in a direction of progressively decreasing elastic moduli is likely to deflect sooner than when the moduli are uniform or increasing. The model is applied to the scorpion cuticle, the laminated structure of which is composed of layers of helical units (Bouligands) with inward decreasing moduli and thickness, interleaved with stiff unidirectional fibrous layers (interlayers). The decreasing moduli act to deflect cracks, whereas the stiff interlayers serve as crack arrestors, making the cuticle less vulnerable to external defects induced by its exposure to harsh living conditions. These concepts may be applied in the design of synthetic laminated structures to improve their damage tolerance and resilience.

A Bio-Based Supramolecular Adhesive: Ultra-High Adhesion Strengths at both Ambient and Cryogenic Temperatures and Excellent Multi-Reusability

Developing high-performance and reusable adhesives from renewable feedstocks is of significance to sustainable development, yet it still remains a formidable task. Herein, castor oil, melevodopa, and iron ions are used as building blocks to construct a novel bio-based supramolecular adhesive (BSA) with outstanding adhesion performances. It is prepared through partial coordination between melevodopa functionalized castor oil and Fe3+ ions. Noncovalent interactions between adherends and the catechol unit from melevodopa contribute to reinforcing adhesion, and the metal-ligand coordination between catechol and Fe3+ ions is utilized to strengthen cohesion. By combining strong adhesion and tough cohesion, the prepared BSA achieves an adhesion strength of 14.6 MPa at ambient temperature, a record-high value among reported bio-based adhesives as well as supramolecular adhesives to the best of knowledge. It also outperforms those adhesives at cryogenic temperature, realizing another record-high adhesion strength of 9.5 MPa at -196 °C. In addition, the BSA displays excellent multi-reusability with more than 87% of the original adhesion strength remaining even after reuse for ten times. It is highly anticipated that this line of research will provide a new insight into designing bio-based adhesives with outstanding adhesion performances and excellent multi-reusability.

Preparation and Characterization of Plant Protein Adhesives with Strong Bonding Strength and Water Resistance

Plant protein adhesive has received considerable attention because of their renewable raw material and no harmful substances such as formaldehyde. However, for the plant protein adhesive used in the field of plywood, low cost, strong water resistance, and high bonding strength were the necessary conditions for practical application. In this work, a double-network structure including hydrogen bonds and covalent bonds was built in hot-pressed peanut meal (HPM) protein (HPMP) adhesive, soybean meal (SBM) protein (SBMP) adhesive and cottonseed meal (CSM) protein (CSMP) adhesives. The ether bonds and ester bonds were the most in CSMP adhesive, followed by SBMP adhesive, while the hydrogen bond was the most in HPMP adhesive. The solubility of the HPMP, SBMP, and CSMP adhesives decreased by 14.3%, 24.2%, and 19.4%, the swelling rate decreased by 56.9%, 48.4%, and 78.5%, respectively. The boiling water strength (BWS) of HPMP (0.82 MPa), SBMP (0.92 MPa), and CSMP adhesives reached the bonding strength requirement of China National Standards class I plywood (type I, 0.7 MPa). The wet shear strength (WSS) of HPMP, SBMP, and CSMP adhesives increased by 334.5% (1.26 MPa), 246.3% (1.42 MPa), and 174.1% (1.59 MPa), respectively. This study provided a new theory and method for the development of eco-friendly plant meal protein adhesive and promotes the development of green adhesive.

Small-molecule ionic liquid-based adhesive with strong room-temperature adhesion promoted by electrostatic interaction

Low-molecular-weight adhesives (LMWAs) possess many unique features compared to polymer adhesives. However, fabricating LMWAs with adhesion strengths higher than those of polymeric materials is a significant challenge, mainly because of the relatively weak and unbalanced cohesion and interfacial adhesion. Herein, an ionic liquid (IL)-based adhesive with high adhesion strength is demonstrated by introducing an IL moiety into a Y-shaped molecule replete with hydrogen bonding (H-bonding) interactions. The IL moieties not only destroyed the rigid and ordered H-bonding networks, releasing more free groups to form hydrogen bonds (H-bonds) at the substrate/adhesive interface, but also provided electrostatic interactions that improved the cohesion energy. The synthesized IL-based adhesive, Tri-HT, could directly form thin coatings on various substrates, with high adhesion strengths of up to 12.20 MPa. Advanced adhesives with electrical conductivity, self-healing behavior, and electrically-controlled adhesion could also be fabricated by combining Tri-HT with carbon nanotubes.

A biomimetic adhesive with high adhesion strength and toughness comprising soybean meal, chitosan, and condensed tannin-functionalized boron nitride nanosheets

Soybean meal (SM)-based adhesive can solve the issues of formaldehyde emission and over-reliance of aldehyde-based resins but suffers from poor water resistance, weak adhesion strength, and high brittleness. Herein, a high-performance adhesive inspired by lobster cuticular sclerotization was developed using catechol-rich condensed tannin-functionalized boron nitride nanosheets (CT@BNNSs), amino-containing chitosan (CS), and SM (CT@BNNSs/CS/SM). The oxidative crosslinking between the catechol and amino, initiated by oxygen at high temperatures, formed a strengthened and water-resistant interior network. These strong intermolecular interactions induced by phenol-amine synergy accompanied by the reinforcement of uniformly dispersed BNNSs improved the load transfer and energy dissipation capacity, endowing the adhesive with great cohesion strength. Given these synergistic effects, the biomimetic CT@BNNSs/CS/SM adhesive caused noticeable improvements in water tolerance, mechanical strength, and toughness over the neat SM adhesive, e.g., enhanced wet shear strength (1.46 vs. 0.66 MPa, respectively), boiling water shear strength (0.92 vs. 0.43 MPa, respectively), and debonding work (0.368 vs. 0.113 J, respectively). Thus, this study provided a green and low-cost bionic strategy for the preparation of high-performance biomass adhesives.

Strong and bioactive bioinspired biomaterials, next generation of bone adhesives

The bone adhesive is a clinical requirement for complicated bone fractures always articulated by surgeons. Applying glue is a quick and easy way to fix broken bones. Adhesives, unlike conventional fixation methods such as wires and sutures, improve healing conditions and reduce postoperative pain by creating a complete connection at the fractured joint. Despite many efforts in the field of bone adhesives, the creation of a successful adhesive with robust adhesion and appropriate bioactivity for the treatment of bone fractures is still in its infancy. Because of the resemblance of the body's humid environment to the underwater environment, in the latest decades, researchers have pursued inspiration from nature to develop strong bioactive adhesives for bone tissue. The aim of this review article is to discuss the recent state of the art in bone adhesives with a specific focus on biomimetic adhesives, their action mechanisms, and upcoming perspective. Firstly, the adhesive biomaterials with specific affinity to bone tissue are introduced and their rational design is studied. Consequently, various types of synthetic and natural bioadhesives for bone tissue are comprehensively overviewed. Then, bioinspired-adhesives are described, highlighting relevant structures and examples of biomimetic adhesives mainly made of DOPA and the complex coacervates inspired by proteins secreted in mussel and sandcastle worms, respectively. Finally, this article overviews the challenges of the current bioadhesives and the future research for the improvement of the properties of biomimetic adhesives for use as bone adhesives.

An injectable and biodegradable hydrogel incorporated with photoregulated NO generators to heal MRSA-infected wounds

The development of degradable hydrogel fillers with high antibacterial activity and wound-healing property is urgently needed for the treatment of infected wounds. Herein, an injectable, degradable, photoactivated antibacterial hydrogel (MPDA-BNN6@Gel) was developed by incorporating BNN6-loaded mesoporous polydopamine nanoparticles (MPDA-BNN6 NPs) into a fibrin-based hydrogel. After administration, MPDA-BNN6@Gel created local hyperthermia and released large quantities of NO gas to treat methicillin-resistant Staphylococcus aureus infection under the stimulation of an 808 nm laser. Experiments confirmed that the bacteria were eradicated through irreversible damage to the cell membrane, genetic metabolism, and material energy. Furthermore, in the absence of laser irradition, the fibrin and small amount of NO that originated from MPDA-BNN6@Gel promoted wound healing in vivo. This work indicates that MPDA-BNN6@Gel is a promising alternative for the treatment of infected wounds and provides a facile tactic to design a photoregulated bactericidal hydrogel for accelerating infected wound healing. STATEMENT OF SIGNIFICANCE: The development of a degradable hydrogel with high antibacterial activity and wound-healing property is an urgent need for the treatment of infected wounds. Herein, an injectable, degradable, and photo-activated antibacterial hydrogel (MPDA-BNN6@Gel) has been developed by incorporating BNN6-loaded mesoporous polydopamine nanoparticles (MPDA-BNN6 NPs) into a fibrin-based hydrogel. After administration of MPDA-BNN6@Gel, the MPDA-BNN6@Gel could generate local hyperthermia and release large quantities of NO gas to treat the methicillin-resistant Staphylococcus aureus infection under the irradiation of 808 nm laser. Furthermore, in the absence of a laser, the fibrin and a small amount of NO originating from MPDA-BNN6@Gel could promote wound healing in vivo.

Bio-Inspired Binder Design for a Robust Conductive Network in Silicon-Based Anodes

Due to the severe volume variations during electrochemical processes, Si-based anodes suffer from poor cycling performance as the result of a collapsed conductive network. In this regard, a key strategy for fully exploiting the capacity potential of Si-based anodes is to construct a robust conductive network through rational binder design. In this work, a bio-inspired conductive binder (PFPQDA) is designed by introducing dopamine-functionalized fluorene structure units (DA) into a conductivity enhanced polyfluorene-typed copolymer (PFPQ) to enhance its mechanical properties. Through constructing hierarchical binding networks and resilient electron transportations within both nano-sized Si and micro-sized SiOx electrodes via interweaved interactions, the PFPQDA successfully suppresses the electrode expansion and maintains the integrity of conductive pathways. Consequently, owing to the favorable properties of PFPQDA, Si-based anodes exhibit improved cycling performance and rate capability with an areal capacity over 2.5 mAh cm-2 .

Strong Dynamic Interfacial Adhesion by Polymeric Ionic Liquids under Extreme Conditions

Interfacial adhesion under extreme conditions has attracted increasing attention owing to its potential application of stopping leakages of oil or natural gas. However, interfacial adhesion is rarely stable at ultralow temperatures and in organic solvents, necessitating the elucidation of the molecular-level processes. Herein, we used the intermolecular force-control strategy to prepare four linear polymers by tuning the proportion of hydrogen bonding and the number of electrostatic sites. The obtained polymeric ion liquids displayed strong dynamic adhesion at various interfaces. They also efficiently tolerated organic solvents and ultracold temperatures. Highly reversible rheological behaviors are observed within a thermal cycle between high and ultracold temperatures. Temperature-dependent infrared spectra and theoretical calculation reveal thermal reversibility and interfacial adhesion/debonding processes at the molecular level, respectively. This intermolecular force-control strategy may be applied to produce environmentally adaptive functional materials for real applications.

Tough, Instant, and Repeatable Adhesion of Self-Healable Elastomers to Diverse Soft and Hard Surfaces

Repeatability and high adhesion toughness are usually contradictory for common polymer adhesives. Repeatability requires temporary interactions between the adhesive and the substrate, while high adhesion toughness is usually achieved by permanent bonding. Integrating these two features into one adhesive system is still a daunting challenge. Here, the development of a series of viscoelastic elastomers composed of a soft and hard segment is reported, which exhibit tough, instant, yet repeatable adhesion to a variety of soft and hard surfaces. Such a combination of mutually exclusive properties is attributed to the synergy of high mobility of polymer chains and massive viscoelastic dissipation of the elastomers around the interface. By optimizing the relaxation time and mechanical dissipation, the resulting adhesives can achieve a tough yet repeatable adhesion toughness above 2000 J m^-2 , superior to the best-in-class commercial adhesives. Numerous acrylate monomers are proven applicable to the preparation of such adhesives, validating the universality of the fabrication method. The application of these elastomers as adhesive and protective layers in soft electronics by virtue of their universal and tough adhesion to various soft and hard substrates is also demonstrated.

A silk fibroin based bioadhesive with synergistic photothermal-reinforced antibacterial activity

Bioadhesives have gained considerable popularity for application in wound closure. However, applying bioadhesives incurs risks associated with bacterial infection during wound healing. Hence, in this study, a silk fibroin based bioadhesive was constructed via employing natural macromolecule, silk fibroin (SF), to spontaneously coassemble with natural plant polyphenol, tannic acid (TA), and iron oxide nanoparticles (Fe₃O₄ NPs). In the system, the natural macromolecule SF plays a key role in fabricating the macromolecular network matrix due to the change of the secondary structure of SF (from random coil to β-sheet) under the trigger of TA. Importantly, the strong hydrogen bonding interactions between SF and TA, and the coordination bonds between TA and Fe₃O₄ NPs endow the bioadhesive with high extensibility, self-healing properties, and considerable wet adhesion. Meanwhile, the synergy between the inherent photothermal properties of Fe₃O₄ NPs and TA/Fe³⁺ complexes under near-infrared (NIR) radiation enables the bioadhesive superior photothermal-reinforced antibacterial activity. The multifunctional natural macromolecule bioadhesive is a potential candidate in clinical wound management for improved outcomes, especially in infected wounds.

Synthesis of Dithiocatechol-Pendant Polymers

Although the synthesis of thiophenol-pendant polymers was reported in the 1950s, the polymers generally suffered from oxidation and became insoluble in organic solvents, hampering detailed characterization and further applications. Dithiocatechol-pendant polymers, which have one additional ortho-thiol group than thiophenol-pendant polymers, have never been synthesized, despite their promise in various applications due to their analogous molecular structure with catechol-pendant polymers. Herein, we report the first synthesis of dithiocatechol-pendant polymers using a novel protection-deprotection strategy. We carefully examined the synthetic routes and identified the deprotection conditions that do not cause cross-linking of the dithiocatechol moieties. Because the resulting dithiocatechol-pendant polymers were soluble in common organic solvents (e.g., tetrahydrofuran and N,N-dimethylformamide), the polymers can be fully characterized by standard spectroscopic methods, providing valuable data for future researchers. We also showed that besides free-radical polymerization, reversible addition-fragmentation chain-transfer polymerization can also be adopted to synthesize dithiocatechol-pendant polymers. This work paves the way for the exploitation of dithiocatechol-containing polymers for the fabrication of novel functional materials.

A comparison of adhesive polysulfides initiated by garlic essential oil and elemental sulfur to create recyclable adhesives

Sulfur and garlic essential oil can initiate polymerization with a variety of natural monomers to form sustainable adhesives. The sulfur source has a substantial impact on the adhesion strength and material properties.

Exploiting Redox-Complementary Peptide/Polyoxometalate Coacervates for Spontaneously Curing into Antimicrobial Adhesives

Recently, there has been a wave of reports on the fabrication of peptide-based underwater adhesives with the aim of understanding the adhesion mechanism of marine sessile organisms or creating new biomaterials beyond nature. However, the poor shear adhesion performance of the current peptide adhesives has largely hindered their applications. Herein, we proposed to sequentially perform the interfacial adhesion and bulk cohesion of peptide-based underwater adhesives using two redox-complementary peptide/polyoxometalate (POM) coacervates. The oxidative coacervates were prepared by mixing oxidative H₅PMo₁₀V₂O₄₀ and cationic peptides in an aqueous solution. The reductive coacervates consisted of K₅BW₁₂O₄₀ and cysteine-containing reductive peptides. Each of the individual coacervate has well-defined spreading capacity to achieve fast interfacial attachment and adhesion, but their cohesion is poor. However, after mixing the two redox-complementary coacervates at the target surface, effective adhesion and spontaneous curing were observed. We identified that the spontaneous curing resulted from the H₅PMo₁₀V₂O₄₀-regulated oxidization of cysteine-containing peptides. The formed intermolecular disulfide bonds improved the cross-linking density of the dual-peptide/POM coacervates, giving rise to the enhanced bulk cohesion and mechanical strength. More importantly, the resultant adhesives showcased excellent bioactivity to selectively suppress the growth of Gram-positive bacteria due to the presence of the polyoxometalates. This work raises further potential in the creation of biomimetic adhesives through the orchestrating of covalent and noncovalent interactions in a sequential fashion.

Self-Healing Silicone Elastomer with Stable and High Adhesion in Harsh Environments

Adhesive and self-healing elastomers are urgently needed for their convenience and intelligence in biological medicine, flexible electronics, intelligent residential systems, etc. However, their inevitable use in harsh environments results in further enhancement requirements of the structure and performance of adhesive and self-healing elastomers. Herein, a novel self-healing and high-adhesion silicone elastomer was designed by the synergistic effect of multiple dynamic bonds. It revealed excellent stretchability (368%) and self-healing properties at room temperature (98.1%, 5 h) and in a water environment (96.4% for 5 h). Meanwhile, the resultant silicone elastomer exhibited high adhesion to metal and nonmetal and showed stable adhesion in harsh environments, such as under acidic (pH 1) and alkaline (pH 12) environments, salt water, petroleum ether, water, etc. Furthermore, it was applied as a shatter-proof protective layer and a rust-proof coating, proving its significant potential in intelligent residential system applications.

Design principles for creating synthetic underwater adhesives

Water and adhesives have a conflicting relationship as demonstrated by the failure of most man-made adhesives in underwater environments. However, living creatures routinely adhere to substrates underwater. For example, sandcastle worms create protective reefs underwater by secreting a cocktail of protein glue that binds mineral particles together, and mussels attach themselves to rocks near tide-swept sea shores using byssal threads formed from their extracellular secretions. Over the past few decades, the physicochemical examination of biological underwater adhesives has begun to decipher the mysteries behind underwater adhesion. These naturally occurring adhesives have inspired the creation of several synthetic materials that can stick underwater - a task that was once thought to be "impossible". This review provides a comprehensive overview of the progress in the science of underwater adhesion over the past few decades. In this review, we introduce the basic thermodynamics processes and kinetic parameters involved in adhesion. Second, we describe the challenges brought by water when adhering underwater. Third, we explore the adhesive mechanisms showcased by mussels and sandcastle worms to overcome the challenges brought by water. We then present a detailed review of synthetic underwater adhesives that have been reported to date. Finally, we discuss some potential applications of underwater adhesives and the current challenges in the field by using a tandem analysis of the reported chemical structures and their adhesive strength. This review is aimed to inspire and facilitate the design of novel synthetic underwater adhesives, that will, in turn expand our understanding of the physical and chemical parameters that influence underwater adhesion.

Design of tough adhesive from commodity thermoplastics through dynamic crosslinking

Tough adhesives provide resistance against high debonding forces, and these adhesives are difficult to design because of the simultaneous requirement of strength and ductility. Here, we report a design of tough reversible/recyclable adhesive materials enabled by incorporating dynamic covalent bonds of boronic ester into commodity triblock thermoplastic elastomers that reversibly bind with various fillers and substrates. The spectroscopic measurements and density functional theory calculations unveil versatile dynamic covalent binding of boronic ester with various hydroxy-terminated surfaces such as silica nanoparticles, aluminum, steel, and glass. The designed multiphase material exhibits exceptionally high adhesion strength and work of debonding with a rebonding capability, as well as outstanding mechanical, thermal, and chemical resistance properties. Bonding and debonding at the interfaces dictate hybrid material properties, and this revelation of tailored dynamic interactions with multiple interfaces will open up a new design of adhesives and hybrid materials.

Reversible Dendritic-Crystal-Reinforced Polymer Gel for Bioinspired Adaptable Adhesive

High-strength and reversible adhesion technology, which is a universal phenomenon in nature but remains challenging for artificial synthesis, is essential for the development of modern science. Existing adhesive designs without interface versatility hinder their application to arbitrary surfaces. Bioinspired by creeper suckers, a crystal-fiber reinforced polymer gel adhesive with ultrastrong adhesion strength and universal interface adaptability is creatively prepared via introducing a room-temperature crystallizable solvent into the polymer network. The gel adhesive formed by hydrogen bonding interaction between crystal fibers and polymer network can successfully realize over 9.82 MPa reversible adhesion strength for rough interface and 406.87 J m^-2 peeling toughness for skin tissue. In situ anchoring is achieved for adapting to different geometrical surfaces. The adhesion performance can be significantly improved with the further increase of the interfacial roughness and hydrophilicity, whose dissipation mechanism is simulated by finite element analysis. The melting-crystallization equilibrium of the crystal fibers is proved by synchrotron radiation scattering. Accordingly, reversible phase-transition triggered by light and heat can realize the controlled adhere-detach recycle. Later adjustments to the monomers or crystals are expected to broaden its applications to various fields such as bioelectronics, electronic processing, and machine handling.

Robust Antiwater and Anti-oil-fouling Double-Sided Tape Enabled by SiO2 Reinforcement and a Liquefied Surface

Realizing simultaneous antiwater and anti-oil-fouling adhesion is extremely challenging owing to the solvated overlayer on the surface of substrates. Herein, we develop a supertough polyacrylate-based tape bearing SiO₂ as a reinforcing filler and a solvent to liquefy the surface. The SiO₂ reinforcement enhances the cohesion strength, while the liquefied surface not only expels the solvated overlayer but also improves the interfacial wettability and interaction. This material design imparts the double-sided tape with admirable antiwater and anti-oil-fouling adhesion performance, which far exceeds that of commercial tapes, as well as high transparency and long-term stability. In addition, we carry out an in-depth study on the adhesive mechanism for the tape and clarify the role of the solvent and the interaction between SiO₂ and a polymer matrix. This work provides a novel strategy for designing antiwater and anti-oil-fouling adhesives with wide applications in various fields such as leakage repair, antiseep, underwater adhesion, building materials, and biological adhesives.

Adhering Low Surface Energy Materials without Surface Pretreatment via Ion-Dipole Interactions

Low surface energy materials resist adhesion due to their chemical inertness and non-wetting properties. Herein, we report the creation of a transparent ionogel adhesive that uses ion-dipole interactions to achieve a higher bonding performance to polytetrafluoroethylene (PTFE) relative to most commercial glues. The ionogel adhesive is composed of a poly(hexafluorobutyl acrylate-co-methyl methacrylate) random copolymer and a hydrophobic ionic liquid. The prepared ionogel can adhere to various hydrophobic substrates, such as PTFE, polypropylene, and polyethylene, as well as hydrophilic glass, ceramics, and steel. The design strategy and adhesion behavior are well interpreted using the density functional theory calculations and molecular dynamics simulations. The straightforward ultraviolet-curing method, high optical clarity, versatile adhesion ability, and reversible adhesion capabilities make this high-performance adhesive a promising product for commercialization.

Folic Acid-Based Coacervate Leading to a Double-Sided Tape for Adhesion of Diverse Wet and Dry Substrates

Adhesives are crucial both in nature and in diversified artificial fields, and developing environment-friendly adhesives with economic procedures remains a great challenge. We report that folic acid-based coacervates can be a new category of excellent adhesives for all kinds of surfaces with long-lasting adhesiveness. Aided by the electrostatic interaction between the π-π stacked folic acid quartets and polycations, the resultant coacervates are able to interact with diversified substrates via a polyvalent hydrogen bond, coordination, and electrostatic interactions. The adhesivity to wood is superior to the strong commercial glues, but without releasing any toxic components. Upon evaporating water, the coacervate can be casted into a non-adhesive flexible self-supporting film, which restores the adhesive coacervate immediately on contacting water with original adhesive ability. In this way, the coacervate can be facilely tailored into a double-sided tape (DST), which is convenient for storage and application under ambient conditions. Given its excellent adhesive performance, release of nontoxic gases, and convenience in storage and application, the folic acid-based DST is very promising as a new adhesive material.