Flexible Electrically Conductive Nanocomposite Membrane Based on Bacterial Cellulose and Polyaniline

Design and characterization of an electrochemically-modulated membrane chromatography device

Membrane separations offer a compelling alternative to traditional chromatographic methods by overcoming mass transport limitations. We introduce an additional degree of freedom in modulating membrane chromatography by using metalized membranes in a potential-driven process. Investigating the impact of a gold coating on membrane characteristics, the sputtered gold layer enhances the surface conductivity with stable electrochemical behavior. However, this comes at the expense of reduced permeability, wettability, and static binding capacity (∼ 474 µg g-1 of maleic acid). The designed device displayed a homogenous flow distribution, and the membrane electrodes exhibit predominantly capacitive behavior during potential application. Modulating the electrical potential during the adsorption and desorption phase strongly influenced the binding and elution behavior of anion-exchange membranes. Switching potentials between ±1.0 V vs. Ag/AgCl induces desorption, confirming the process principle. Elution efficiency reaches up to 58 % at -1.0 V vs. Ag/AgCl in the desorption phase without any alteration of the mobile phase. Increasing the potential perturbation ranging from +1.0 V to -1.0 V vs. Ag/AgCl resulted in reduced peak width and improved elution behavior, demonstrating the feasibility of electrochemically-modulated membrane chromatography. The developed process has great potential as a gentle and sustainable separation step in the biotechnological and chemical industry.

Synthesis and evaluation of cellulose/polypyrrole composites as polymer electrolytes for lithium-ion battery application

Natural polymers as battery components have a number of advantages, including availability, biodegradability, unleakage, stable form, superior process, electrochemical stability, and low cost. In other sides, conductive polymers can improve the electrochemical properties of the battery, such as charge/discharge rates, cycling stability, and overall energy storage capacity. Therefore, the combination of these two materials can provide acceptable features. In this study, polymer electrolytes based on cellulose have been synthesized by solution casting method to prepare a thin polymer film. Then, polypyrrole (PPy) was blended with cellulose in different weight ratios. To prevent electrical conductivity of blends, PPy was used <10 wt%. The electrochemical properties of prepared electrolytes have been investigated by different methods. The results showed that ionic conductivity was increased by addition of PPy to cellulose due to the creation of pores and also due to the high dielectric constant of conductive polymers. All synthesized electrolytes had suitable ionic conductivity (in the range of 10-3 S cm-1), significant charge capacity, stable cyclic performance, excellent electrochemical stability (above 4.8 V), and high cation transfer number (between 0.38 and 0.66 for pure cellulose and the sample containing 10 wt% PPy).

Harnessing Nature's Ingenuity: A Comprehensive Exploration of Nanocellulose from Production to Cutting-Edge Applications in Engineering and Sciences

Primary material supply is the heart of engineering and sciences. The depletion of natural resources and an increase in the human population by a billion in 13 to 15 years pose a critical concern regarding the sustainability of these materials; therefore, functionalizing renewable materials, such as nanocellulose, by possibly exploiting their properties for various practical applications, has been undertaken worldwide. Nanocellulose has emerged as a dominant green natural material with attractive and tailorable physicochemical properties, is renewable and sustainable, and shows biocompatibility and tunable surface properties. Nanocellulose is derived from cellulose, the most abundant polymer in nature with the remarkable properties of nanomaterials. This article provides a comprehensive overview of the methods used for nanocellulose preparation, structure-property and structure-property correlations, and the application of nanocellulose and its nanocomposite materials. This article differentiates the classification of nanocellulose, provides a brief account of the production methods that have been developed for isolating nanocellulose, highlights a range of unique properties of nanocellulose that have been extracted from different kinds of experiments and studies, and elaborates on nanocellulose potential applications in various areas. The present review is anticipated to provide the readers with the progress and knowledge related to nanocellulose. Pushing the boundaries of nanocellulose further into cutting-edge applications will be of particular interest in the future, especially as cost-effective commercial sources of nanocellulose continue to emerge.

Conductive bacterial cellulose: From drug delivery to flexible electronics

Bacterial cellulose (BC) is a chemically pure, non-toxic, and non-pyrogenic natural polymer with high mechanical strength and a complex fibrillar porous structure. Due to these unique biological and physical properties, BC has been amply used in the food industry and, to a somewhat lesser extent, in medicine and cosmetology. To expand its application the BC structure can be modified. This review presented some recent developments in electrically conductive BC-based composites. The as-synthesized BC is an excellent dielectric. Conductive polymers, graphene oxide, nanoparticles and other materials are used to provide it with conductive properties. Conductive bacterial cellulose (CBC) is currently investigated in numerous areas including electrically conductive scaffolds for tissue regeneration, implantable and wearable biointerfaces, flexible batteries, sensors, EMI shielding composites. However, there are several issues to be addressed before CBC composites can enter the market, namely, composite mechanical strength reduction, porosity decrease, change in chemical characteristics. Some of them can be addressed both at the stage of synthesis, biologically, or by adding (nano)materials with the required properties to the BC structure. We propose several solutions to meet the challenges and suggest some promising BC applications.

Review of Bacterial Nanocellulose as Suitable Substrate for Conformable and Flexible Organic Light-Emitting Diodes

As the development of nanotechnology progresses, organic electronics have gained momentum in recent years, and the production and rapid development of electronic devices based on organic semiconductors, such as organic light-emitting diodes (OLEDs), organic photovoltaic cells (OPVs), and organic field effect transistors (OFETs), among others, have excelled. Their uses extend to the fabrication of intelligent screens for televisions and portable devices, due to their flexibility and versatility. Lately, great efforts have been reported in the literature to use them in the biomedical field, such as in photodynamic therapy. In tandem, there has been considerable interest in the design of advanced materials originating from natural sources. Bacterial nanocellulose (BNC) is a natural polymer synthesized by many microorganisms, notably by non-pathogenic strains of Komagataeibacter (K. xylinus, K. hansenii, and K. rhaeticus). BNC shows distinct physical and mechanical properties, including its insolubility, rapid biodegradability, tensile strength, elasticity, durability, and nontoxic and nonallergenic features, which make BNC ideal for many areas, including active and intelligent food packaging, sensors, water remediation, drug delivery, wound healing, and as conformable/flexible substrates for application in organic electronics. Here, we review BNC production methods, properties, and applications, focusing on electronic devices, especially OLEDs and flexible OLEDs (FOLEDs). Furthermore, we discuss the future progress of BNC-based flexible substrate nanocomposites.

Bioadhesive Gauze Embedded with Chitosan-Butein Bioconjugate: A Redox-Active pH Sensor Platform

With the ever-growing global wound care market, demand for robust redox-active healthcare material is obvious for the construction of wearable sensor platforms. Surface reactive functional group-rich material like chitosan holds huge potential for electrochemical biosensor application. Herein, a metal-free redox-active chitosan-butein (CSB) bioconjugate is processed into epidermal bioadhesive electrode material useful for pH sensors promising toward wound site analysis. A two-electrode system devised for conducting carbon-reinforced silver chloride paste and CSB-modified carbon/silver chloride matrix was used as a reference and working electrodes, respectively. Dimensions of working and reference electrodes (4 mm) were designed by 2D cutter plotter-assisted stenciling. The cross-sectional topology of the constructed adhesive CSB-sensor platform exhibits an average surface thickness of 183 ± 2 μm. Cyclic voltammetric analysis revealed the inherent 2e^-/2H⁺ transfer attributed to the catechol OH groups of graft polymerized CSB modified on adhesive gauze. As-fabricated modified electrode substrates exhibit distinguishable potential differences with respect to electrolytes of varied pH (between 5 to 9), promising for wound site analysis.

Bacterial Cellulose-Based Polymer Nanocomposites: A Review

Bacterial cellulose (BC) is currently one of the most popular environmentally friendly materials with unique structural and physicochemical properties for obtaining various functional materials for a wide range of applications. In this regard, the literature reporting on bacterial nanocellulose has increased exponentially in the past decade. Currently, extensive investigations aim at promoting the manufacturing of BC-based nanocomposites with other components such as nanoparticles, polymers, and biomolecules, and that will enable to develop of a wide range of materials with advanced and novel functionalities. However, the commercial production of such materials is limited by the high cost and low yield of BC, and the lack of highly efficient industrial production technologies as well. Therefore, the present review aimed at studying the current literature data in the field of highly efficient BC production for the purpose of its further usage to obtain polymer nanocomposites. The review highlights the progress in synthesizing BC-based nanocomposites and their applications in biomedical fields, such as wound healing, drug delivery, tissue engineering. Bacterial nanocellulose-based biosensors and adsorbents were introduced herein.

Bacterial cellulose: A promising biopolymer with interesting properties and applications

The ever-increasing demands for materials with desirable properties led to the development of materials that impose unfavorable influences on the environment and the ecosystem. Developing a low-cost, durable, and eco-friendly functional material with biological origins has become necessary to avoid these consequences. Bacterial cellulose generated by bacteria dispenses excellent structural and functional properties and satisfies these requirements. BC and BC-derived materials are essential in developing pure and environmentally safe functional materials. This review offers a detailed understanding of the biosynthesis of BC, properties, various functionalization methods, and applicability in biomedical, water treatment, food storage, energy conversion, and energy storage applications.

Methods for stability assessment of electrically conductive membranes

The surface properties of electrically conductive membranes (ECMs) govern their advanced abilities. During operation, these properties may differ considerably from their initially measured properties. Depending on their operating conditions, ECMs may undergo various degrees of passivation. ECM passivation can detrimentally impact their real time performance, causing large deviations from expected behaviour based on their initially measured properties. Quantifying these changes will enable consistent performance comparisons across the active and electrically conductive membrane research field. As such, consistent methods must be established to quantify ECM membrane properties. In this work, we proposed three standardized methods to assess the electrochemical, chemical, and physical stability of such membrane coatings: 1) electrochemical oxidation, 2) surface scratch testing, and 3) pressurized leaching. ECMs were synthesized by the most common approach - coating support ultrafiltration (UF) and/or microfiltration (MF) polyethersulfone (PES) membranes with carbon nanotubes (CNT) cross-linked with polyvinyl alcohol (PVA) and two types of cross-linkers (either succinic acid (SA) or glutaraldehyde (GA)). We then evaluated these ECMs based on the three standardized methods: 1) We evaluated electrochemical stability as a function of electro-oxidation induced by applying anodic potentials. 2) We measured the scratch resistance to quantify the surface mechanical stability. 3) We measured physical stability by quantifying the leaching of PVA during separation of a model foulant (polyethylene oxide (PEO)). Our methods can be extended to all types of electrically conductive membranes including MF, UF, nanofiltration (NF), and reverse osmosis (RO) ECMs. We propose that these fundamental measurements are critical to assessing the viability of ECMs for industrial MF, UF, NF, and RO applications.•Anodic-oxidation was used to check the electrochemical stability of ECMs•Depth of penetration resulted from scratch test is an indicator of the electrically conductive membrane coating's mechanical stability•The leaching of the main components forming the nanolayer was quantified to assess the membranes' physical stability.

Construction of Biomass-Derived Hybrid Organogel Electrodes with a Cross-Linking Conductive Network for High-Performance All-Solid-State Supercapacitors

The biomass-based inter-transmission network architecture is expected to act on all-solid-state supercapacitors (ASSSCs) by building excellent conductive paths and achieving high ionic conductivity to promote their development as future electronic devices. Here, biomass-derived hybrid organogel electrodes constructed by incorporating polyaniline (PANI) into cellulose/dealkaline lignin (C/DL) film architectures exhibit an impressive specific capacitance (582 F g^-1 at 1 A g^-1) due to the effective dispersion and doping of PANI. Moreover, the specific capacitance of the best C/DL-PANI electrode is nearly 19 times higher than that of a cellulose-PANI electrode, which is attributed to the contribution of DL to the pseudocapacitance. ASSSCs assembled using the C/DL-PANI electrodes and the DL gel electrolyte exhibit excellent specific capacitance (344 F g^-1 at 1 A g^-1), Coulombic efficiency (∼100% for 5000 cycles), cycle stability (85.7% for 5000 cycles at 1 A g^-1), and energy density (58.1 W h kg^-1 at 0.5 kW kg^-1). The ASSSCs showed a comparable or even higher electrochemical performance than the reported PANI-based or biomass-based ASSSCs, which can be due to the conductive network of the biomass-derived electrodes, the migration of ions between the electrodes through the gel electrolyte ion pathway, and the interfacial synergy. This innovative work paves the way for the development of ASSSC applications based on biomass materials.

In Situ Fabrication of Porous MOF/COF Hybrid Photocatalysts for Visible-Light-Driven Hydrogen Evolution

Construction of porous metal-organic framework (MOF)/covalent organic framework (COF) hybrid photocatalysts for enriched structures and unprecedented properties is still a great challenge but highly desirable. Herein, a new series of Cu₃(HHTP)₂-MOF/Tp-Pa-1-COF hybrids with different MOF content are successfully fabricated. The as-prepared MOF/COF hybrids exhibit intimate interaction based on the coordination of Cu ions with the carbonyl oxygen and enamine nitrogen groups in Tp-Pa-1. The integrated conductive Cu₃(HHTP)₂ is able to act as an excellent electron extractor instead of noble metal cocatalysts to significantly promote the charge transfer and inhibit the recombination of photogenerated electron-hole pairs. As a results, the optimized photocatalyst with Cu₃(HHTP)₂:Tp-Pa-1 ratio of 1:15 achieves the highest hydrogen evolution rate of 1.76 mmol·h^-1·g^-1 under visible-light irradiation, which is about 93 times higher than that of the pure Tp-Pa-1 and even slightly higher than that of the Tp-Pa-1 with Pt (3 wt %) as a cocatalyst.

Continuous Meter-Scale Wet-Spinning of Cornlike Composite Fibers for Eco-Friendly Multifunctional Electronics

"Green" solvent-dissolved cellulose enables functional reuse of waste cotton fabrics. This work will not only achieve high-value utilization of biomass but also overcome microplastic pollution. There is a significant challenge in the continuous meter-scale synthesis of sensing fibers for commercial applications with high productivity. Herein, waste cellulose fabrics was recycled by the NaOH/urea system to produce regenerated cellulose (RC) and then cornlike polyaniline (PANI) was anchored on the RC fibers by in situ polymerization of aniline through continuous meter-scale wet-spinning. In our findings, the morphologies and possible growth of PANI layers on the RC surface can be tailored by various ammonium persulfate (APS) contents in a coagulation bath. Especially, composite fibers (PC_0.5) exhibited superior electrical conductivity and highly sensitive responsiveness to organic vapors and human motions including exhalation/inhalation, finger, and wrist joints. Further, the possible sensing mechanism of cornlike PC_0.5 has been proposed, and its GF value is 23.8. This study realized the conversion from cheap waste fibers to high-value conductive fibers with excellent performances for multifunctional wearable sensors and energy devices via a simple and "green" method.

Electrically conductive biocompatible composite aerogel based on nanofibrillated template of bacterial cellulose/polyaniline/nano-clay

Bacterial cellulose (BC) aerogel owing to its porous and 3D structure, poses a suitable matrix for embedding nanomaterials and polymers. Herein, BC composites comprising nano-clay/polyaniline (PANI) were synthesized via a two-step procedure. Clay nanoplatelets were dispersed in the BC membrane to form a nanofibrillated template for aniline in-situ polymerization leading to formation of a double interconnected network of electrically conductive path within the aerogel. Deposition of PANI particles on BC/clay nanocomposite was confirmed by FTIR, XRD, FESEM, and EDX techniques. The surface electrical conductivity of 0.49 S/cm was obtained for the composite aerogel comprising 5 wt% nano-clay which is 16 folds higher than that of the sample without nano-clay. Thermal stability and storage modulus of the aerogels was improved by inclusion of PANI and nano-clay. Synergistic effect of clay and polyaniline on biocompatibility and cell adhesion was obtained with no mutagenic or carcinogenic effects. The developed electrically conductive composite aerogels can be utilized as suitable scaffolds for tissue engineering applications demanding a good balance of flexibility, dimensional and thermal stability and biocompatibility.

Biocompatible SWCNT Conductive Composites for Biomedical Applications

The efficiency of devices for biomedical applications, including tissue engineering and neuronal stimulation, heavily depends on their biocompatibility and performance level. Therefore, it is important to find adequate materials that meet the necessary requirements such as (i) being intrinsically compatible with biological systems, (ii) providing a sufficient electronic conductivity that promotes efficient signal transduction, (iii) having "soft" mechanical properties comparable to biological structures, and (iv) being degradable in physiological solution. We have developed organic conducting biocompatible single-walled carbon nanotubes (SWCNT) composites based on bovine serum albumin, carboxymethylcellulose, and acrylic polymer and investigated their properties, which are relevant for biomedical applications. This includes ζ-potential measurements, conductivity analyses, and SEM micrographs, the latter providing a local analysis of SWCNT distribution in the base material. We observed the development of the electrical conductivity of the SWCNT composites exposed to 1 mM KCl electrolyte for 40 days, representing a high stability of the samples. The conductivity of samples reaches 1300 S/m for 0.45 wt.% nanotubes. Moreover, we demonstrated the biocompatibility of the composites via cultivating fibroblast cell culture. Finally, we showed that composite coating results in the longer lifespan of cells on the surface. Overall, the SWCNT-based conductive composites might be a promising material for extended biomedical applications.

Mechanism and Compatibility of Pretreated Lignocellulosic Biomass and Polymeric Mixed Matrix Membranes: A Review

In this paper, a review of the compatibility of polymeric membranes with lignocellulosic biomass is presented. The structure and composition of lignocellulosic biomass which could enhance membrane fabrications are considered. However, strong cell walls and interchain hindrances have limited the commercial-scale applications of raw lignocellulosic biomasses. These shortcomings can be surpassed to improve lignocellulosic biomass applications by using the proposed pretreatment methods, including physical and chemical methods, before incorporation into a single-polymer or copolymer matrix. It is imperative to understand the characteristics of lignocellulosic biomass and polymeric membranes, as well as to investigate membrane materials and how the separation performance of polymeric membranes containing lignocellulosic biomass can be influenced. Hence, lignocellulosic biomass and polymer modification and interfacial morphology improvement become necessary in producing mixed matrix membranes (MMMs). In general, the present study has shown that future membrane generations could attain high performance, e.g., CO2 separation using MMMs containing pretreated lignocellulosic biomasses with reachable hydroxyl group radicals.

Bacterial cellulose-based magnetic nanocomposites: A review

Bacterial cellulose (BC) is a natural polymer that has unique and interesting structural, physical and chemical properties. These characteristics make it very attractive as a starting point for several novel developments in innovative research. However, the pristine BC lacks certain properties, in particular, magnetic property, which can be imparted to BC by incorporation of several types of magnetic nanoparticles. Magnetic nanocomposites based on BC exhibit additional magnetic functionality on top of the excellent properties of pristine BC, which make them promising materials with potential uses in various medical and environmental applications, as well as in advanced electronic devices. This review has compiled information about all classes of BC magnetic nanocomposites fabricated by various synthesis approaches and an overview of applications as well as improved features of these materials. A summary of the key developments of BC magnetic nanocomposites and emphasis on novel advances in this field is presented.

Branched aramid nanofiber-polyaniline electrodes for structural energy storage

Strong electrodes with good energy storage capabilities are necessary to accommodate the current needs for structural and flexible electronics. To this end, conjugated polymers such as polyaniline (PANI) have attracted much attention due to their exceptional energy storage performance. However, PANI is typically brittle and requires the use of substrates for structural support. Here, we report a strategy for developing free-standing structural supercapacitor and battery electrodes based on PANI. More specifically, aniline is polymerized in the presence of branched aramid nanofibers (BANFs) and single walled carbon nanotubes (SWCNTs). This results in a network morphology that allows for efficient load transfer and electron transport, leading to electrodes with capacity values up to 128 ± 5 mA h g-1 (vs. a theoretical capacity of 147 mA h g-1), Young's modulus of 4 ± 0.5 GPa, and tensile strength of 40 ± 4 MPa. Furthermore, the charge storage mechanism is investigated, in which both Faradaic and non-Faradaic contributions are observed. This work demonstrates an efficient strategy for designing structural electrodes based on conjugated polymers.

Biopolymeric Membrane Enriched with Chitosan and Silver for Metallic Ions Removal

The present paper synthesized, characterized, and evaluated the performance of the novel biopolymeric membrane enriched with cellulose acetate and chitosan (CHI)-silver (Ag) ions in order to remove iron ion from the synthetic wastewater using a new electrodialysis system. The prepared membranes were characterized by Fourier Transforms Infrared Spectroscopy-Attenuated Total Reflection (FTIR-ATR), Thermal Gravimetric Analysis (TGA) and Differential Thermal Analysis (DSC), contact angle measurements, microscopy studies, and electrochemical impedance spectroscopy (EIS). The electrodialysis experiments were performed at the different applied voltages (5, 10, and 15 V) for one hour, at room temperature. The treatment rate (T_E) of iron ions, current efficiency (I_E), and energy consumption (W_c) were calculated. FTIR-ATR spectra evidenced that incorporation of CHI-Ag ions into the polymer mixture led to a polymer-metal ion complex formation within the membrane. The TGA-DSC analysis for the obtained biopolymeric membranes showed excellent thermal stability (>350 °C). The contact angle measurements demonstrated the hydrophobic character of the polymeric membrane and a decrease of it by CHI-Ag adding. The EIS results indicated that the silver ions induced a higher ionic electrical conductivity. The highest value of the iron ions treatment rate (>60%) was obtained for the biopolymeric membrane with CHI-Ag ions at applied voltage of 15 V.

Chemistry, Structures, and Advanced Applications of Nanocomposites from Biorenewable Resources

Researchers have recently focused on the advancement of new materials from biorenewable and sustainable sources because of great concerns about the environment, waste accumulation and destruction, and the inevitable depletion of fossil resources. Biorenewable materials have been extensively used as a matrix or reinforcement in many applications. In the development of innovative methods and materials, composites offer important advantages because of their excellent properties such as ease of fabrication, higher mechanical properties, high thermal stability, and many more. Especially, nanocomposites (obtained by using biorenewable sources) have significant advantages when compared to conventional composites. Nanocomposites have been utilized in many applications including food, biomedical, electroanalysis, energy storage, wastewater treatment, automotive, etc. This comprehensive review provides chemistry, structures, advanced applications, and recent developments about nanocomposites obtained from biorenewable sources.

Ultra-fast heat dissipating aerogels derived from polyaniline anchored cellulose nanofibers as sustainable microwave absorbers

Electromagnetic (EM) pollution is ubiquitous and has soared to a great extent in the past few decades. The use of plant sourced cellulose nanofibers to fabricate sustainable and high performance electromagnetic shielding materials is foreseen as a green solution by the electronics industry to address this unseen pollutant. In this view, we report a facile and environmentally benign strategy to synthesize ultra-light and highly conductive aerogels derived from cellulose nanofibers (CNF) decorated with polyaniline (PANI) via a simple in-situ polymerization and subsequent freeze drying process devoid of any volatile organic solvents. The obtained conductive aerogels exhibited density as low as 0.01925 g/cc with a maximum EMI shielding value -32 dB in X band region. These porous shields demonstrated strong microwave absorption behavior (95 %) with minimal reflection (5 %) coupled with high specific EMI SE value ∼1667 dB.cm³. g^-1 which make these aerogels a potential candidate for use in telecommunication, military and defense applications.

Carboxymethyl Cellulose (CMC) as a Template for Laccase-Assisted Oxidation of Aniline

Polyaniline (PANi) is a conducting polymer which has been subject of intensive research on the exploitation of new products and applications. The main aim of the work is the development of a conductive bacterial cellulose (BC)-based material by enzymatic-assisted polymerization of aniline. For this, we study the role of carboxymethyl cellulose (CMC) as a template for the in situ polymerization of aniline. Bacterial cellulose was used as the supporting material for the entrapment of CMC and for the in situ oxidation reactions. The amount of CMC entrapped inside BC was optimized as well as the conditions for laccase-assisted oxidation of aniline. The new oligomers were evaluated by spectrometric techniques, namely 1H NMR and MALDI-TOF, and the functionalized BC surfaces were analyzed by thermogravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM), and reflectance spectrophotometry. The conductivity of the developed materials was evaluated using the four-probe methodology. The oligomers obtained after reaction in the presence of CMC as template display a similar structure as when the reaction is conducted only in BC. Though, after oxidation in the presence of this template, the amount of oligomers entrapped inside BC/CMC is considerably higher conferring to the material greater electrical conductivity and coloration. The use of CMC as a template for aniline oxidation on BC seems to be a promising and cheap strategy to improve the yield of functionalization and increment the properties of the materials, namely electrical conductivity and coloration.

Ultrasensitive Physical, Bio, and Chemical Sensors Derived from 1-, 2-, and 3-D Nanocellulosic Materials

Sensors are of increasing interest since they can be applied to daily life in different areas from various industrial sectors. As a natural nanomaterial, nanocellulose plays a vital role in the development of novel sensors, particularly in the context of constructing multidimensional architectures. This review summarizes the utilization of nanocellulose including cellulose nanofibers, cellulose nanocrystals, and bacterial cellulose for sensor design, mainly focusing on the influence of nanocellulose on the sensing performance of these sensors. Special attention is paid to nanocellulose in different forms (1D, 2D, and 3D) to highlight the impact of nanocellulose constructed structures. The aim is to provide a critical review on the most recent progress (especially after 2017) related to nanocellulose-containing sensors, since there are significantly increasing research activities in this area. Moreover, the outlook for the development of nanocellulose-containing sensors is also provided at the end of this work.

Allylamine PECVD Modification of PDMS as Simple Method to Obtain Conductive Flexible Polypyrrole Thin Films

In this paper, we report a one-step method to obtain conductive polypyrrole thin films on flexible substrates. To do this, substrates were modified through allylamine plasma grafting to create a high amount of reactive amine groups on PDMS surface. These groups are used during polypyrrole particle synthesis as anchoring points to immobilize the polymeric chains on the substrate during polymerization. Surface morphology of polypyrrole thin films are modified, tailoring the polyelectrolyte used in the polypyrrole synthesis obtaining different shapes of nanoparticles that conform to the film. Depending on the polyelectrolyte molecular weight, the shape of polypyrrole particles go from globular (500 nm diameter) to a more constructed and elongated shape. The films obtained with this methodology reflected great stability under simple bending as well as good conductivity values (between 2.2 ± 0.7 S/m to 5.6 ± 0.2 S/cm).

Poly(4-vinylaniline)/Polyaniline Bilayer-Functionalized Bacterial Cellulose for Flexible Electrochemical Biosensors

A bacterial cellulose (BC) nanofibril network is modified with an electrically conductive polyvinylaniline/polyaniline (PVAN/PANI) bilayer for construction of potential electrochemical biosensors. This is accomplished through surface-initiated atom transfer radical polymerization of 4-vinylaniline, followed by in situ chemical oxidative polymerization of aniline. A uniform coverage of the BC nanofiber with 1D supramolecular PANI nanostructures is confirmed by Fourier transform infrared, X-ray diffractogram, and CHN elemental analysis. Cyclic voltammograms evince the switching in the electrochemical behavior of BC/PVAN/PANI nanocomposites from the redox peaks at 0.74 V, in the positive scan and at -0.70 V, in the reverse scan, (at 100 mV·s^-1 scan rate). From these redox peaks, PANI is the emeraldine form with the maximal electrical performance recorded, showing charge-transfer resistance as low as 21 Ω and capacitance as high as 39 μF. The voltage-sensible nanocomposites can interact with neural stem cells isolated from the subventricular zone (SVZ) of the brain, through stimulation and characterization of differentiated SVZ cells into specialized and mature neurons with long neurites measuring up to 115 ± 24 μm length after 7 days of culture without visible signs of cytotoxic effects. The findings pave the path to the new effective nanobiosensor technologies for nerve regenerative medicine, which demands both electroactivity and biocompatibility.

Nanocellulose applications in sustainable electrochemical and piezoelectric systems: A review

Recent studies advocate the use of cellulose nanomaterials (CNs) as a sustainable carbohydrate polymer in numerous innovative electronics for their quintessential features such as flexibility, low thermal expansion and self-/directed assembly within multiphase matrices. Herein, we review the contemporary advances in CN-built electrochemical systems and highlight the constructive effects of these nanoscopic entities once engineered in conductive composites, proton exchange membranes (PEMs), electrochromics, energy storage devices and piezoelectric sensors. The adopted strategies and designs are discussed in view of CN roles as copolymer, electrolyte reservoir, binder and separator. Finally, physiochemical attributes and durability of resulting architectures are compared to conventional materials and the possible challenges/solutions are delineated to realize the promising capabilities. The volume of the up-to-present literature in the field indeed implies to nanocellulose overriding importance and the presented angles perhaps shed more lights on prospect of the biosphere's most dominant biomaterial in the energy-related arena that deserve attention.

Synthesis and Characterization of a High Flux Nanocellulose-Cellulose Acetate Nanocomposite Membrane

Despite the advantages of membrane processes, their high energy requirement remains a major challenge. Fabrication of nanocomposite membranes by incorporating various nanomaterials in the polymer matrix has shown promise for enhancing membrane flux. In this study, we embed functionalized cellulose nanofibers (CNFs) with high aspect ratios in the polymer matrix to create hydrophilic nanochannels that reduce membrane resistance and facilitate the facile transport of water molecules through the membrane. The results showed that the incorporation of 0.1 wt % CNF into the polymer matrix did not change the membrane flux (~15 L · m - 2 · h - 1 ) and Bovine Serum Albumin (BSA) Fraction V rejection, while increasing the CNF content to 0.3 wt % significantly enhanced the flux by seven times to ~100 L · m - 2 · h - 1 , but the rejection was decreased to 60-70%. Such a change in membrane performance was due to the formation of hydrophilic nanochannels by the incorporation of CNF (corroborated by the SEM images), decreasing the membrane resistance, and thus enhancing the flux. When the concentration of the CNF in the membrane matrix was further increased to 0.6 wt %, no further increase in the membrane flux was observed, however, the BSA rejection was found to increase to 85%. Such an increase in the rejection was related to the electrostatic repulsion between the negatively-charged CNF-loaded nanochannels and the BSA, as demonstrated by zeta potential measurements. SEM images showed the bridging effect of the CNF in the nanochannels with high CNF contents.

Design and Optimization of Flexible Polypyrrole/Bacterial Cellulose Conductive Nanocomposites Using Response Surface Methodology

Flexible conductive materials have greatly promoted the rapid development of intelligent and wearable textiles. This article reports the design of flexible polypyrrole/bacterial cellulose (PPy/BC) conductive nanocomposites by in situ chemical polymerization. Box-Behnken response surface methodology has been applied to optimize the process. The effects of the pyrrole amount, the molar ratio of HCl to pyrrole and polymerization time on conductivity were investigated. A flexible PPy/BC nanocomposite was obtained with an outstanding electrical conductivity as high as 7.34 S cm⁻¹. Morphological, thermal stability and electrochemical properties of the nanocomposite were also studied. The flexible PPy/BC composite with a core-sheath structure exhibited higher thermal stability than pure cellulose, possessed a high areal capacitance of 1001.26 mF cm⁻² at the discharge current density of 1 mA cm⁻², but its cycling stability could be further improved. The findings of this research demonstrate that the response surface methodology is one of the most effective approaches for optimizing the conditions of synthesis. It also indicates that the PPy/BC composite is a promising material for applications in intelligent and wearable textiles.

Organic Thin Paper of Cellulose Nanofiber/Polyaniline Doped with (±)-10-Camphorsulfonic Acid Nanohybrid and Its Application to Electromagnetic Shielding

A superior electrical conductivity of 38.5 S/cm and an electromagnetic shielding (EMS) effectiveness of -30 dB (-545 dB/mm) across a wide frequency range of 0-15 GHz, including the X-band, were achieved with thin organic paper of (55 μm) cellulose nanofiber (CNF)/polyaniline (PANI) doped with (±)-10-camphorsulfonic acid nanohybrid. Both electrical conductivity and EMS effectiveness of the PANI-coated CNF were strongly affected by the amount and type of dopant, which could be tunable after fabrication process via simple in situ oxidative polymerization of aniline. Flexible and free-standing film was obtained, since CNF provides good mechanical property without diminishing the electrical property of PANI.