Surface modification of nanoporous alumina surfaces with poly(ethylene glycol)

Exploring Novel Sensor Design Ideas through Concentration-Induced Conformational Changes in PEG Single Chains

Polyethylene glycol (PEG) is an artificial polymer with good biocompatibility and a low cost, which has a wide range of applications. In this study, the dynamic response of PEG single chains to different ion concentrations was investigated from a microscopic point of view based on single-molecule force spectroscopy, revealing unique interactions that go beyond the traditional sensor-design paradigm. Under low concentrations of potassium chloride, PEG single chains exhibit a gradual reduction in rigidity, while, conversely, high concentrations induce a progressive increase in rigidity. This dichotomy serves as the cornerstone for a profound understanding of PEG conformational dynamics under diverse ion environments. Capitalizing on the remarkable sensitivity of PEG single chains to ion concentration shifts, we introduce innovative sensor-design ideas. Rooted in the adaptive nature of PEG single chains, these sensor designs extend beyond the traditional applications, promising advancements in environmental monitoring, healthcare, and materials science.

Preparation of AlON Powder by Carbothermal Reduction and Nitridation with Assisting by Silane Coupling Agent

In the preparation processes of aluminum oxynitride (AlON) powders by carbothermal reduction and nitridation, the homogeneity of mixed raw powders between Al₂O₃ and C is a critical factor by which the final composition and related properties of AlON transparent ceramic will be decided. In this paper, a silane coupling agent was used as a dispersant to optimize the distribution uniformity of raw material of Al₂O₃ and C, and the preparation of AlON powder with controllable composition and its distribution is investigated. The results show that the silane dispersant could effectively improve the distribution uniformity of raw material. The silane coupling agent contains functional groups of -SiH₃ and -C_nH_2n+1O. XPS showed that the silane could react with C and Al₂O₃ to form the Si-C bond and C-Al₂O₃ bond, respectively. The silane coupling agent provides a connected bridge for raw material powders. When the amount of the silane was 5 wt%, the mixed powder had a great distribution uniformity. The addition of silane coupling agent improved the reactivity of raw materials and decreased the synthesis temperature of AlON. The single-phase AlON powder was obtained after the Al₂O₃/C mixed powder was kept at 1670 °C for 30 min. Furthermore, the grain size of AlON powder was 100-200 nm with an AlN content of 27.5 mol%. With the increase of holding time to 4 h, the grain size increased to 15 μm, indicating that sintering between particles occurred, which may reduce the sintering activity of the powder.

Functionalised Anodised Aluminium Oxide as a Biocidal Agent

In this article, we describe the antimicrobial properties of a new composite based on anodic aluminium oxide (AAO) membranes containing propyl-copper-phosphonate units arranged at a predetermined density inside the AAO channels. The samples were prepared with four concentrations of copper ions and tested as antimicrobial drug on four different strains of Escherichia coli (K12, R2, R3 and R4). For comparison, the same strains were tested with three types of antibiotics using the minimal inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) tests. Moreover, DNA was isolated from the analysed bacteria which was additionally digested with formamidopyrimidine-DNA glycosylase (Fpg) protein from the group of repair glycosases. These enzymes are markers of modified oxidised bases in nucleic acids produced during oxidative stress in cells. Preliminary cellular studies, MIC and MBC tests and digestion with Fpg protein after modification of bacterial DNA suggest that these compounds may have greater potential as antibacterial agents than antibiotics such as ciprofloxacin, bleomycin and cloxacillin. The described composites are highly specific for the analysed model Escherichia coli strains and may be used in the future as new substitutes for commonly used antibiotics in clinical and nosocomial infections in the progressing pandemic era. The results show much stronger antibacterial properties of the functionalised membranes on the action of bacterial membranes in comparison to the antibiotics in the Fpg digestion experiment. This is most likely due to the strong induction of oxidative stress in the cell through the breakdown of the analysed bacterial DNA. We have also observed that the intermolecular distances between the functional units play an important role for the antimicrobial properties of the used material. Hence, we utilised the idea of the 2D solvent to tailor them.

The ethylene glycol-mediated sol-gel synthesis of nano AlF3: structural and acidic properties after different post treatments

In this work, the structure and surface acidity of nano AlF₃ prepared by the ethylene glycol-mediated sol-gel process, followed by different post treatments including post-fluorination and calcination, were systematically investigated. FT-IR, elemental analysis, XPS and TG-DTA-MS results indicate the ethylene glycol strongly interacts with the as-prepared AlF₃ precursor, thus stabilizing the formed nano particles. MAS NMR spectroscopy combined with in situ FT-IR and HRTEM techniques reveal that AlF₆, AlO_6-xF_x and AlO₆ species are present in the resulting X-ray amorphous nano AlF₃. The fraction of AlF₆ species formed after post-fluorination significantly increases, whereas more AlO_6-xF_x species are formed just after calcination. After a comparable post-fluorination treatment, the CHClF₂ dismutation activity at room temperature indicates that nano AlF₃ prepared according the ethylene glycol-mediated route does not possess the same super-strong acidity as HS-AlF₃ prepared by the fluorolytic sol-gel method, although NH₃-TPD and N₂-sorption results indicate larger BET surface areas and high concentration of acid sites for the former as compared to the latter. This might be rationalized based on the absence of terminal fluorine species and the presence of a significant number of AlO_6-xF_x and AlO₆ species in the resulting nano AlF₃ as revealed by ²⁷Al, ¹⁹F MAS NMR and HRTEM. An interesting consequence is that these oxygen-containing species stabilize the microstructure of AlF₃ formed, resulting in improved thermal stability of these phases as compared to "classically" prepared HS-AlF₃.

Protoporphyrin IX copolymer with poly(ethylene glycol) methacrylate and its thermoresponsive properties

Porphyrins and their derivatives have been widely used in catalysis, energy conversion, photonics, and biomedicine; however, their use in biological applications is restricted by their limited solubility in aqueous systems. We have prepared a water-soluble copolymer containing moieties of naturally occurring protoporphyrin IX using direct copolymerization of a poly(ethylene glycol) (PEG) methacrylate monomer with protoporphyrin IX via free-radical polymerization. The content of protoporphyrin IX in the copolymer was determined by 1H NMR and UV–vis absorption spectroscopies. Their solution properties and the photostability of the protoporphyrin IX moiety in the copolymer provide direct evidence of the covalent incorporation of protoporphyrin IX within the copolymer. The copolymer showed a reversible phase transition in aqueous solution due to the lower critical solution temperature (LCST). The phase transition temperature varies with the pH of the solutions because of the protonation of the carboxylic acid groups. This copolymer may be useful as an alternative thermoresponsive material for biomedical applications.

Nano-porous anodic alumina: fundamentals and applications in tissue engineering

Recently, nanomaterials have been widely utilized in tissue engineering applications due to their unique properties such as the high surface to volume ratio and diversity of morphology and structure. However, most methods used for the fabrication of nanomaterials are rather complicated and costly. Among different nanomaterials, anodic aluminum oxide (AAO) is a great example of nanoporous structures that can easily be engineered by changing the electrolyte type, anodizing potential, current density, temperature, acid concentration and anodizing time. Nanoporous anodic alumina has often been used for mammalian cell culture, biofunctionalization, drug delivery, and biosensing by coating its surface with biocompatible materials. Despite its wide application in tissue engineering, thorough in vivo and in vitro studies of AAO are still required to enhance its biocompatibility and thereby pave the way for its application in tissue replacements. Recognizing this gap, this review article aims to highlight the biomedical potentials of AAO for applications in tissue replacements along with the mechanism of porous structure formation and pore characteristics in terms of fabrication parameters.

Anti-Adhesion Behavior from Ring-Strain Amine Cyclic Monolayers Grafted on Silicon (111) Surfaces

In this manuscript, a series of amine tagged short cyclic molecules (cyclopropylamine, cyclobutylamine, cyclopentylamine and cyclohexylamine) were thermally grafted onto p-type silicon (111) hydride surfaces via nucleophilic addition. The chemistries of these grafting were verified via XPS, AFM and sessile droplet measurements. Confocal microscopy and cell viability assay was performed on these surfaces incubated for 24 hours with triple negative breast cancer cells (MDA-MB 231), gastric adenocarcinoma cells (AGS) endometrial adenocarcinoma (Hec1A). All cell types had shown a significant reduction when incubated on these ring-strain cyclic monolayer surfaces than compared to standard controls. The expression level of focal adhesion proteins (vinculin, paxilin, talin and zyxin) were subsequently quantified for all three cell types via qPCR analysis. Cells incubate on these surface grafting were observed to have reduced levels of adhesion protein expression than compared to positive controls (collagen coating and APTES). A potential application of these anti-adhesive surfaces is the maintenance of the chondrocyte phenotype during in-vitro cell expansion. Articular chondrocytes cultured for 6 days on ring strained cyclopropane-modified surfaces was able to proliferate but had maintained a spheroid/aggregated phenotype with higher COL2A1 and ACAN gene expression. Herein, these findings had help promote grafting of cyclic monolayers as an viable alternative for producing antifouling surfaces.

Interaction of blood plasma proteins with superhemophobic titania nanotube surfaces

The need to improve blood biocompatibility of medical devices is urgent. As soon as blood encounters a biomaterial implant, proteins adsorb on its surfaces, often leading to several complications such as thrombosis and failure of the device. Therefore, controlling protein adsorption plays a major role in developing hemocompatible materials. In this study, the interaction of key blood plasma proteins with superhemophobic titania nanotube substrates and the blood clotting responses was investigated. The substrate stability was evaluated and fibrinogen adsorption and thrombin formation from plasma were assessed using ELISA. Whole blood clotting kinetics was also investigated, and Factor XII activation on the substrates was characterized by an in vitro plasma coagulation time assay. The results show that superhemophobic titania nanotubes are stable and considerably decrease surface protein adsorption/Factor XII activation as well as delay the whole blood clotting, and thus can be a promising approach for designing blood contacting medical devices.

Surface Modification of Pseudoboehmite-Coated Aluminum Plates with Squaramic Acid Amphiphiles

The functionalization of interfaces has become very important for the protection or modification of metal (metal oxides) surfaces. The functionalization of aluminum is particularly interesting because of its relevance in fabricating components for electronic devices. In this work, the utilization of squaramic acids for the functionalization of aluminum substrates is reported for the first time. The physicochemical properties of the interfaces rendered by n-alkyl squaramic acids on aluminum metal substrates coated with pseudoboehmite [Al(O)x(OH)y] layers are characterized by contact angle, grazing-angle Fourier-transform infrared spectroscopy, atomic force microscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, and matrix-assisted laser desorption ionization time-of-flight. Moreover, we could confirm the squaramic functionalization of the substrates by diffuse reflectance UV-vis spectroscopy, which cannot be used for the characterization of UV-vis-inactive substrates such as carboxylates and phosphonates, commonly used for coating metallic surfaces. Remarkably, the results of sorption experiments indicate that long-chain alkyl squaramic acid desorbs from activated-aluminum substrates at a reduced rate compared to palmitic acid, a carboxylic acid frequently used for the functionalization of metal oxide surfaces. Theoretical calculations indicate that the improved anchoring properties of squaramic acids over carboxylates are probably due to the formation of additional hydrogen bonding interactions on the interface. Accordingly, we propose N-alkyl squaramic acids as new moieties for efficient functionalization of metal oxides.

Real-Time Monitoring of Biotinylated Molecules Detection Dynamics in Nanoporous Anodic Alumina for Bio-Sensing

The chemical modification, or functionalization, of the surfaces of nanomaterials is a key step to achieve biosensors with the best sensitivity and selectivity. The surface modification of biosensors usually comprises several modification steps that have to be optimized. Real-time monitoring of all the reactions taking place during such modification steps can be a highly helpful tool for optimization. In this work, we propose nanoporous anodic alumina (NAA) functionalized with the streptavidin-biotin complex as a platform towards label-free biosensors. Using reflective interferometric spectroscopy (RIfS), the streptavidin-biotin complex formation, using biotinylated thrombin as a molecule model, was monitored in real-time. The study compared the performance of different NAA pore sizes in order to achieve the highest response. Furthermore, the optimal streptavidin concentration that enabled the efficient detection of the biotinylated thrombin attachment was estimated. Finally, the ability of the NAA-RIfS system to quantify the concentration of biotinylated thrombin was evaluated. This study provides an optimized characterization method to monitor the chemical reactions that take place during the biotinylated molecules attachment within the NAA pores.

Nanoporous solid-state membranes modified with multi-wall carbon nanotubes with anti-biofouling property

PURPOSE

Nanoporous membranes have been employing more than before in applications such as biomedical due to nanometer hexagonal pores array. Biofouling is one of the important problems in these applications that used nanoporous membranes and are in close contact with microorganisms. Surface modification of the membrane is one way to prevent biofilm formation; therefore, the membrane made in this work is modified with carbon nanotubes.

METHODS

In this work, nanoporous solid-state membrane (NSSM) was made by a two-step anodization method, and then modified with carbon nanotubes (NSSM-multi-wall carbon nanotubes [MWCNT]) by a simple chemical reaction. Techniques such as atomic force microscopy (AFM), energy dispersive X-ray (EDAX), field emission scanning electron microscopy (FESEM), Fourier-transform infrared spectroscopy (FTIR), contact angle (CA), surface free energy (SFE), protein adsorption, flow cytometry, and MTT assay were used for membrane characterization.

RESULTS

The BSA protein adsorption capacity reduced from 992.54 to 97.24 (μg mL-1 cm-2) after modification. The findings of flow cytometry and MTT assay confirmed that the number of dead bacteria was higher on the NSSM-MWCNT surface than that of control. Adsorption models of Freundlich and Langmuir and kinetics models were studied to understand the governing mechanism by which bacteria migrate to the membrane surface.

CONCLUSION

The cell viability of absorbed bacteria on the NSSM-MWCNT was disrupted in direct physical contact with carbon nanotubes. Then, the dead bacteria were desorbed from the surface of the hydrophilic membrane. The results of this research showed that NSSM-MWCNT containing carbon nanotubes have significant antimicrobial and self-cleaning property that can be used in many biomedical devices without facing the eminent problem of biofouling.

Stacked Nanoporous Anodic Alumina Gradient-Index Filters with Tunable Multispectral Photonic Stopbands as Sensing Platforms

This study presents the development and optical engineering of stacked nanoporous anodic alumina gradient-index (NAA-GIFs) filters with tunable multispectral photonic stopbands for sensing applications. The structure of these photonic crystals (PC) is formed by stacked layers of NAA produced with sinusoidally modified effective medium. The progressive modification of the sinusoidal period during the anodization process enables the generation and precise tuning of the characteristic photonic stopbands (PSB) (i.e., one per sinusoidal period in the anodization profile) of these PC structures. Four types of NAA-GIFs featuring three distinctive PSBs positioned within the visible spectral region are developed. The sensitivity of the effective medium of these NAA-GIFs is systematically assessed by measuring spectral shifts in the characteristic PSBs upon infiltration of their nanoporous structure with analytical solutions of d-glucose with several concentrations (0.025-1 M). This study provides new insights into the intrinsic relationship between the nanoporous architecture of these PCs and their optical properties, generating opportunities to fabricate advanced optical sensing systems for high-throughput and multiplexed detection of analytes in a single sensing platform.

Reversible Immobilization of Proteins in Sensors and Solid-State Nanopores

The controlled functionalization of surfaces with proteins is crucial for many analytical methods in life science research and biomedical applications. Here, a coating for silica-based surfaces is established which enables stable and selective immobilization of proteins with controlled orientation and tunable surface density. The coating is reusable, retains functionality upon long-term storage in air, and is applicable to surfaces of complex geometry. The protein anchoring method is validated on planar surfaces, and then a method is developed to measure the anchoring process in real time using silicon nitride solid-state nanopores. For surface attachment, polyhistidine tags that are site specifically introduced into recombinant proteins are exploited, and the yeast nucleoporin Nsp1 is used as model protein. Contrary to the commonly used covalent thiol chemistry, the anchoring of proteins via polyhistidine tag is reversible, permitting to take proteins off and replace them by other ones. Such switching in real time in experiments on individual nanopores is monitored using ion conductivity. Finally, it is demonstrated that silica and gold surfaces can be orthogonally functionalized to accommodate polyhistidine-tagged proteins on silica but prevent protein binding to gold, which extends the applicability of this surface functionalization method to even more complex sensor devices.

Nanocylindrical confinement imparts highest structural order in molecular self-assembly of organophosphonates on aluminum oxide

We report the impact of geometrical constraint on intramolecular interactions in self-assembled monolayers (SAMs) of alkylphosphonates grown on anodically oxidized aluminum (AAO). Molecular order in these films was determined by sum frequency generation (SFG) spectroscopy, a more sensitive measure of order than infrared absorption spectroscopy. Using SFG we show that films grown on AAO are, within detection limits, nearly perfectly ordered in an all-trans alkyl chain configuration. In marked contrast, films formed on planar, plasma-oxidized aluminum oxide or α-Al₂O₃ (0001) are replete with gauche defects. We attribute these differences to the nanocylindrical structure of AAO, which enforces molecular confinement.

Shear Strength and Interfacial Toughness Characterization of Sapphire-Epoxy Interfaces for Nacre-Inspired Composites

The common tensile lap-shear test for adhesive joints is inappropriate for brittle substrates such as glasses or ceramics where stress intensifications due to clamping and additional bending moments invalidate results. Nevertheless, bonding of glasses and ceramics is still important in display applications for electronics, in safety glass and ballistic armor, for dental braces and restoratives, or in recently developed bioinspired composites. To mechanically characterize adhesive bondings in these fields nonetheless, a novel approach based on the so-called Schwickerath test for dental sintered joints is used. This new method not only matches data from conventional analysis but also uniquely combines the accurate determination of interfacial shear strength and toughness in one simple test. The approach is verified for sapphire-epoxy joints that are of interest for bioinspired composites. For these, the procedure not only provides quantitative interfacial properties for the first time, it also exemplarily suggests annealing of sapphire at 1000 °C for 10 h for mechanically and economically effective improvements of the interfacial bond strength and toughness. With increases of strength and toughness from approximately 8 to 29 MPa and from 2.6 to 35 J/m², respectively, this thermal modification drastically enhances the properties of unmodified sapphire-epoxy interfaces. At the same time, it is much more convenient than wet-chemical approaches such as silanization. Hence, besides the introduction of a new testing procedure for adhesive joints of brittle or expensive substrates, a new and facile annealing process for improvements of the adhesive properties of sapphire is suggested and quantitative data for the mechanical properties of sapphire-epoxy interfaces that are common in synthetic nacre-inspired composites are provided for the first time.

A solid-state cation exchange reaction to form multiple metal oxide heterostructure nanowires

Metal oxide nanostructures have been investigated extensively due to their wide range of physical properties; zinc oxide is one of the most promising materials. It exhibits fascinating functional properties and various types of morphologies. In particular, ZnO heterostructures have attracted great attention because their performance can be modified and further improved by the addition of other materials. In this study, we successfully transformed ZnO nanowires (NWs) into multiple ZnO/Al₂O₃ heterostructure NWs via a solid-state cation exchange reaction. The experiment was carried out in situ via an ultrahigh vacuum transmission electron microscope (UHV-TEM), which was equipped with a video recorder. Moreover, we analyzed the structure and composition of the heterostructure NWs by Cs-corrected STEM equipped with EDS. Based on these experimental results, we inferred a cation exchange reaction ion path model. Additionally, we investigated the defects that appeared after the cation reaction, which resulted from the remaining zinc ions. These multiple heterostructure ZnO/Al₂O₃ NWs exhibited excellent UV sensing sensitivity and efficiency.

Integrative functional transcriptomic analyses implicate specific molecular pathways in pulmonary toxicity from exposure to aluminum oxide nanoparticles

Gene expression profiling has developed rapidly in recent years and it can predict and define mechanisms underlying chemical toxicity. Here, RNA microarray and computational technology were used to show that aluminum oxide nanoparticles (Al2O3 NPs) were capable of triggering up-regulation of genes related to the cell cycle and cell death in a human A549 lung adenocarcinoma cell line. Gene expression levels were validated in Al2O3 NPs exposed A549 cells and mice lung tissues, most of which showed consistent trends in regulation. Gene-transcription factor network analysis coupled with cell- and animal-based assays demonstrated that the genes encoding PTPN6, RTN4, BAX and IER play a role in the biological responses induced by the nanoparticle exposure, which caused cell death and cell cycle arrest in the G2/S phase. Further, down-regulated PTPN6 expression demonstrated a core role in the network, thus expression level of PTPN6 was rescued by plasmid transfection, which showed ameliorative effects of A549 cells against cell death and cell cycle arrest. These results demonstrate the feasibility of using gene expression profiling to predict cellular responses induced by nanomaterials, which could be used to develop a comprehensive knowledge of nanotoxicity.

Microfabrication and in Vivo Performance of a Microdialysis Probe with Embedded Membrane

Microdialysis sampling is an essential tool for in vivo neurochemical monitoring. Conventional dialysis probes are over 220 μm in diameter and have limited flexibility in design because they are made by assembly using preformed membranes. The probe size constrains spatial resolution and governs the amount of tissue damaged caused by probe insertion. To overcome these limitations, we have developed a method to microfabricate probes in Si that are 45 μm thick × 180 μm wide. The probes contain a buried, U-shaped channel that is 30 μm deep × 60 μm wide and terminates in ports for external connection. A 4 mm length of the probe is covered with a 5 μm thick nanoporous membrane. The membrane was microfabricated by deep reactive ion etching through a porous aluminum oxide layer. The microfabricated probe has cross-sectional area that is 79% less than that of the smallest conventional microdialysis probes. The probes yield 2-20% relative recovery at 100 nL/min perfusion rate for a variety of small molecules. The probe was successfully tested in vivo by sampling from the striatum of live rats. Fractions were collected at 20 min intervals (2 μL) before and after an intraperitoneal injection of 5 mg/kg amphetamine. Analysis of fractions by liquid chromatography-mass spectrometry revealed reliable detection of 14 neurochemicals, including dopamine and acetylcholine, at basal conditions. Amphetamine evoked a 43-fold rise in dopamine, a result nearly identical to a conventional dialysis probe in the same animal. The microfabricated probes have potential for sampling with higher spatial resolution and less tissue disruption than conventional probes. It may also be possible to add functionality to the probes by integrating other components, such as electrodes, optics, and additional channels.

Fabrication of highly selective molecularly imprinted membranes for the selective adsorption of methyl salicylate from salicylic acid

Highly selective molecularly imprinted membranes for methyl salicylate were synthesized with 4-vinylpyridine, acrylamide or methacrylic acid as the functional monomer based on the Al₂O₃ microporous ceramic membrane.

Physicochemical properties affect the synthesis, controlled delivery, degradation and pharmacokinetics of inorganic nanoporous materials

Controlling size, shape and uniformity of porous constructs remains a major focus of the development of porous materials. Over the past two decades, we have seen significant developments in the fabrication of new, porous-ordered structures using a wide range of materials, resulting in properties well beyond their traditional use. Porous materials have been considered appealing, due to attractive properties such as pore size length, morphology and surface chemistry. Furthermore, their utilization within the life sciences and medicine has resulted in significant developments in pharmaceutics and medical diagnosis. This article focuses on various classes of porous materials, providing an overview of principle concepts with regard to design and fabrication, surface chemistry and loading and release kinetics. Furthermore, predictions from a multiscale mathematical model revealed the role pore length and diameter could have on payload release kinetics.

Visible-light photocatalysis in Cu2Se nanowires with exposed {111} facets and charge separation between (111) and (1[combining macron]1[combining macron]1[combining macron]) polar surfaces

The search for active narrow band gap semiconductor photocatalysts that directly split water or degrade organic pollutants under solar irradiation remains an open issue. We synthesized Cu2Se nanowires with exposed {111} facets using ethanol and glycerol as morphology controlling agents. The {111} facets were found to be the active facets for decomposing organic contaminants in the entire solar spectrum. Based on the polar structure of the Cu2Se {111} facets, a charge separation model between polar (111) and (1[combining macron]1[combining macron]1[combining macron]) surfaces is proposed. The internal electric field between polar (111) and (1[combining macron]1[combining macron]1[combining macron]) surfaces created by spontaneous polarization drives charge separation. The reduction and oxidation reactions occur on the positive (111) and negative (1[combining macron]1[combining macron]1[combining macron]) polar surfaces, respectively. This suggests the surface-engineering of narrow band gap semiconductors as a strategy to fabricate photocatalysts with high reactivity in the entire solar spectrum. The charge separation model can deepen the understanding of charge transfer in other semiconductor nanocrystals with high photocatalytic activities and offer guidance to design more effective photocatalysts as well as new types of solar cells, photoelectrodes and photoelectric devices.

In Vitro Biocompatibility of Surface-Modified Porous Alumina Particles for HepG2 Tumor Cells: Toward Early Diagnosis and Targeted Treatment

Porous alumina photoluminescence-inherent particles are produced and proposed for the development of biomarkers detectors and localized treatment of HepG2 cells. Nanoporous alumina particles (NPAPs) are amorphous, consist of hexagonally ordered nanometric pores in an alumina matrix, have high chemical stability in physiological pH, and exhibit a high inherent photoluminescence in the visible spectrum independently of their size, selectable from nanometers to tens of micrometers. The surface of NPAPs is chemically modified using two different functionalization methods, a multistep method with (3-aminopropyl)triethoxysilane (APTES) and glutaraldehyde (GLTA) and a novel simplified-step method with silane-PEG-NHS. Fourier Transform infrared spectroscopy analysis confirmed the proper surface modification of the particles for both functionalization methods. HepG2 cells were cultured during different times with growing concentrations of particles. The analysis of cytotoxicity and cell viability of HepG2 cells confirmed the good biocompatibility of NPAPs in all culture conditions. The results prove the suitability of NPAPs for developing new label-free biomarker detectors and advantageous carriers for localized drug delivery.

Nanocarbon-Coated Porous Anodic Alumina for Bionic Devices

A highly-stable and biocompatible nanoporous electrode is demonstrated herein. The electrode is based on a porous anodic alumina which is conformally coated with an ultra-thin layer of diamond-like carbon. The nanocarbon coating plays an essential role for the chemical stability and biocompatibility of the electrodes; thus, the coated electrodes are ideally suited for biomedical applications. The corrosion resistance of the proposed electrodes was tested under extreme chemical conditions, such as in boiling acidic/alkali environments. The nanostructured morphology and the surface chemistry of the electrodes were maintained after wet/dry chemical corrosion tests. The non-cytotoxicity of the electrodes was tested by standard toxicity tests using mouse fibroblasts and cortical neurons. Furthermore, the cell-electrode interaction of cortical neurons with nanocarbon coated nanoporous anodic alumina was studied in vitro. Cortical neurons were found to attach and spread to the nanocarbon coated electrodes without using additional biomolecules, whilst no cell attachment was observed on the surface of the bare anodic alumina. Neurite growth appeared to be sensitive to nanotopographical features of the electrodes. The proposed electrodes show a great promise for practical applications such as retinal prostheses and bionic implants in general.

A phenotypic in vitro model for the main determinants of human whole heart function

This article details the construction and testing of a phenotypic assay system that models in vivo cardiac function in a parallel in vitro environment with human stem cell derived cardiomyocytes. The major determinants of human whole-heart function were experimentally modeled by integrating separate 2D cellular systems with BioMicroelectromechanical Systems (BioMEMS) constructs. The model features a serum-free defined medium to enable both acute and chronic evaluation of drugs and toxins. The integration of data from both systems produced biologically relevant predictions of cardiac function in response to varying concentrations of selected drugs. Sotalol, norepinephrine and verapamil were shown to affect the measured parameters according to their specific mechanism of action, in agreement with clinical data. This system is applicable for cardiac side effect assessment, general toxicology, efficacy studies, and evaluation of in vitro cellular disease models in body-on-a-chip systems.

Engineered therapeutic-releasing nanoporous anodic alumina-aluminum wires with extended release of therapeutics

In this study, we present a nanoengineered therapeutic-releasing system based on aluminum wires featuring nanoporous anodic alumina layers and chitosan coatings. Nanoporous anodic alumina layers are produced on the surface of aluminum wires by electrochemical anodization. These nanoporous layers with precisely engineered nanopore geometry are used as nanocontainers for bovine serum albumin molecules labeled with fluorescein isothiocyanate (BSA-FITC), which is selected as a model drug. The surface of these therapeutic-releasing implants is coated with a biocompatible and biodegradable polymer, chitosan, in order to achieve a sustained release of protein over extended periods of time. The performance of this therapeutic-releasing device is systematically assessed through a series of experiments under static and dynamic flow conditions. In these experiments, the effect of such parameters as the number of layers of chitosan coating and the temperature and pH of the eluting medium is established. The obtained results reveal that the proposed therapeutic-releasing system based on nanoporous aluminum wires can be engineered with sustained release performance for up to 6.5 weeks, which is a critical factor for medical treatments using sensitive therapeutics such as proteins and genes when a localized delivery is desired.

The Effect of Surface Chemistry on the Glass Transition of Polycarbonate Inside Cylindrical Nanopores

The effect of surface chemistry on the glass transition of polycarbonate (PC) inside cylindrical nanopores is studied. Polycarbonate is melt-wetted into nanoporous anodic aluminum oxide (AAO) treated with hydrophobic alkyl- and fluorosilanes of varying length. The curvature observed at the nanowire tips is consistent with a contact angle descriptive of polycarbonate-AAO surface interactions. Differential scanning calorimetry (DSC) thermograms reveal a distinct broadening of the T_g that is related to the motion of polymer chains at the nanopore wall as well as at the core. DSC and thermal gravimetric analysis (TGA) show that polycarbonate infiltrated into a naked AAO template (without silane treatment) degrades upon heating, suggestive of a surface-catalyzed degradation mechanism. It is further shown that silane treatment largely prevents PC thermal degradation.

Nanoporous anodic alumina platforms: engineered surface chemistry and structure for optical sensing applications

Electrochemical anodization of pure aluminum enables the growth of highly ordered nanoporous anodic alumina (NAA) structures. This has made NAA one of the most popular nanomaterials with applications including molecular separation, catalysis, photonics, optoelectronics, sensing, drug delivery, and template synthesis. Over the past decades, the ability to engineer the structure and surface chemistry of NAA and its optical properties has led to the establishment of distinctive photonic structures that can be explored for developing low-cost, portable, rapid-response and highly sensitive sensing devices in combination with surface plasmon resonance (SPR) and reflective interference spectroscopy (RIfS) techniques. This review article highlights the recent advances on fabrication, surface modification and structural engineering of NAA and its application and performance as a platform for SPR- and RIfS-based sensing and biosensing devices.

Membranes to achieve immunoprotection of transplanted islets

Transplantation of islet or beta cells is seen as the cure for type 1 diabetes since it allows physiological regulation of blood glucose levels without requiring any compliance from the patients. In order to circumvent the use of immunosuppressive drugs (and their side effects), semipermeable membranes have been developed to encapsulate and immunoprotect transplanted cells. This review presents the historical developments of immunoisolation and provides an update on the current research in this field. A particular emphasis is laid on the fabrication, characterization and performance of membranes developed for immunoisolation applications.

Studies on fate and toxicity of nanoalumina in male albino rats

The purpose of this study is to follow-up the distribution, lethality percentile doses (LDs) and bioaccumulation of aluminium oxide nanoparticles (Al2O3-NPs, average diameter 9.83 ± 1.61 nm) in some tissues of male albino rats, and to evaluate its genotoxicity to the brain tissues, during acute and sublethal experiments. The LDs of Al2O3-NPs, including median lethal dose (LD50), were estimated after intraperitoneal injection. The computed LD50 at 24 and 48 h were 15.10 and 12.88 g/kg body weight (b.w.), respectively. For acute experiments, the bioaccumulation of aluminium (Al) in the brain, liver, kidneys, intestine and spleen was estimated after 48 h of injection with a single acute dose (3.9, 6.4 and 8.5 g/kg b.w.), while for sublethal experiments it was after 1, 3, 7, 14 and 28 days of injection with 1.3 g/kg b.w. once in 2 days. Multi-way analysis of variance affirmed that Al uptake, in acute experiments, was significantly affected by the injected doses, organs (brain, liver, kidneys, intestine and spleen) and their interactions, while for sublethal experiments an altogether effect based on time (1, 3, 7, 14, 28 days), doses (0 and 1.3 g), organs and their interactions was reported. In addition, Al accumulated in the brain, liver, kidney, intestine and spleen of rats administered with Al2O3-NPs were significantly higher than the corresponding controls, during acute and sublethal experiments. The uptake of Al by the spleen of rats injected with acute doses was greater than that accumulated by kidney>brain>intestine>liver, whereas the brain of rats injected with sublethal dose accumulated lesser amount of Al followed by the kidney<intestine<spleen<liver. Bioaccumulation of Al, in all studied tissues, was positively correlated with the injected doses (in acute term) and the experimental periods (in sublethal term). In the acute and sublethal experiments, comet assay parameters such as the tail intensity (i.e. DNA percentage), tail extent moment and olive tail moment were estimated using a single cell gel electrophoresis/comet assay. The results showed significant increase in DNA percentage damage in the brain cells. The obtained results indicate that bioaccumulation of Al was associated with significantly increased levels of comet parameters that depended on the doses and the experimental periods. In conclusion, Al has a high affinity to get accumulated in tissues to a level that is able to induce genotoxicity. Therefore, bioaccumulation is time, dose and organ dependant.

Functionalized ceramics for biomedical, biotechnological and environmental applications

Surface functionalization has become of paramount importance and is considered a fundamental tool for the development and design of countless devices and engineered systems for key technological areas in biomedical, biotechnological and environmental applications. In this review, surface functionalization strategies for alumina, zirconia, titania, silica, iron oxide and calcium phosphate are presented and discussed. These materials have become particularly important concerning the aforementioned applications, being not only of great academic, but also of steadily increasing human and commercial, interest. In this review, special emphasis is given to their use as biomaterials, biosensors, biological targets, drug delivery systems, implants, chromatographic supports for biomolecule purification and analysis, and adsorbents for toxic substances and pollutants. The objective of this review is to provide a broad picture of the enormous possibilities offered by surface functionalization and to identify particular challenges regarding surface analysis and characterization.

Transformation of polymer nanofibers to nanospheres driven by the Rayleigh instability

We study the thermal annealing effect of poly(methyl methacrylate) (PMMA) nanofibers made from anodic aluminum oxide (AAO) templates and their transformation to PMMA nanospheres. The PMMA nanofibers are prepared by wetting an AAO template with a 30 wt % PMMA solution, followed by the evaporation of the solvent. After the AAO template is removed by a weak base, the PMMA nanofibers are thermally annealed in ethylene glycol, a nonsolvent for PMMA. The surfaces of the nanofibers undulate and transform into nanospheres, driven by the Rayleigh instability. The driving force for the transformation process is the minimization of the interfacial energy between PMMA nanofibers and ethylene glycol. The transformation times at higher annealing temperatures are shorter than those at lower annealing temperatures. This study provides a facile route to prepare polymer nanospheres which are not accessible by other traditional methods.

The role of surface functionalization of colloidal alumina particles on their controlled interactions with viruses

Materials that interact in a controlled manner with viruses attract increasing interest in biotechnology, medicine, and environmental technology. Here, we show that virus-material interactions can be guided by intrinsic material surface chemistries, introduced by tailored surface functionalizations. For this purpose, colloidal alumina particles are surface functionalized with amino, carboxyl, phosphate, chloropropyl, and sulfonate groups in different surface concentrations and characterized in terms of elemental composition, electrokinetic, hydrophobic properties, and morphology. The interaction of the functionalized particles with hepatitis A virus and phages MS2 and PhiX174 is assessed by virus titer reduction after incubation with particles, activity of viruses conjugated to particles, and imaged by electron microscopy. Type and surface density of particle functional groups control the virus titer reduction between 0 and 99.999% (5 log values). For instance, high sulfonate surface concentrations (4.7 groups/nm(2)) inhibit attractive virus-material interactions and lead to complete virus recovery. Low sulfonate surface concentrations (1.2 groups/nm(2)), native alumina, and chloropropyl-functionalized particles induce strong virus-particle adsorption. The virus conformation and capsid amino acid composition further influence the virus-material interaction. Fundamental interrelations between material properties, virus properties, and the complex virus-material interaction are discussed and a versatile pool of surface functionalization strategies controlling virus-material interactions is presented.

Controlling protein-particle adsorption by surface tailoring colloidal alumina particles with sulfonate groups

In this study, we demonstrate the control of protein adsorption by tailoring the sulfonate group density on the surface of colloidal alumina particles. The colloidal alumina (d(50)=179±8nm) is first accurately functionalized with sulfonate groups (SO(3)H) in densities ranging from 0 to 4.7SO(3)H nm(-2). The zeta potential, hydrophilic/hydrophobic properties, particle size, morphology, surface area and elemental composition of the functionalized particles are assessed. The adsorption of three model proteins, bovine serum albumin (BSA), lysozyme (LSZ) and trypsin (TRY), is then investigated at pH 6.9±0.3 and an ionic strength of 3mM. Solution depletion and zeta potential experiments show that BSA, LSZ and TRY adsorption is strongly affected by the SO(3)H surface density rather than by the net zeta potential of the particles. A direct correlation between the SO(3)H surface density, the intrinsic protein amino acid composition and protein adsorption is observed. Thus a continuous adjustment of the protein adsorption amount can be achieved between almost no coverage and a theoretical monolayer by varying the density of SO(3)H groups on the particle surface. These findings enable a deeper understanding of protein-particle interactions and, moreover, support the design and engineering of materials for specific biotechnology, environmental technology or nanomedicine applications.

Fabrication and adhesion of a bio-inspired microarray: capillarity-induced casting using porous silicon mold

Inspired by the setal microstructure found on the gecko's toe-pads, a highly dense array of high-aspect-ratio (HAR) artificial setae has been developed with a novel mold-casting technique using a porous silicon (PSi) template. To overcome the high fluid resistance in the HAR capillary pores, the PSi template surface is modified with a monolayer coating of dimethylsilane. The coating exhibits similar chemical composition and surface energy to the precursor of the poly(dimethylsiloxane) (PDMS) replica. The compatibility between the template and the replica addresses the major challenge of molding HAR microstructures, resulting in high-resolution replicas of artificial PDMS microsetae with complicated geometry resembling a real gecko's setae. The artificial setae are characterized by a mean radius of 1.3 μm, an aspect ratio of 35.1, and a density of ~4.7 × 105 per mm2. Results from adhesion characterizations reveal that with increasing preload, the shear adhesion of micro-setae continually increases while the normal adhesion decreases. The unique adhesion performance is caused by both van der Waals forces and the elastic resistance of PDMS setae. With further structural optimizations and the addition of an actuation mechanism, artificial setal arrays might eventually demonstrate the fascinating adhesion performances of the gecko for mimetic devices such as wall-climbing devices.

The influence of nanostructured materials on biointerfacial interactions

Control over biointerfacial interactions in vitro and in vivo is the key to many biomedical applications: from cell culture and diagnostic tools to drug delivery, biomaterials and regenerative medicine. The increasing use of nanostructured materials is placing a greater demand on improving our understanding of how these new materials influence biointerfacial interactions, including protein adsorption and subsequent cellular responses. A range of nanoscale material properties influence these interactions, and material toxicity. The ability to manipulate both material nanochemistry and nanotopography remains challenging in its own right, however, a more in-depth knowledge of the subsequent biological responses to these new materials must occur simultaneously if they are ever to be affective in the clinic. We highlight some of the key technologies used for fabrication of nanostructured materials, examine how nanostructured materials influence the behavior of proteins and cells at surfaces and provide details of important analytical techniques used in this context.