ZnO/Cu nanocomposite: a platform for direct electrochemistry of enzymes and biosensing applications

Road Map of Semiconductor Metal-Oxide-Based Sensors: A Review

Identifying disease biomarkers and detecting hazardous, explosive, flammable, and polluting gases and chemicals with extremely sensitive and selective sensor devices remains a challenging and time-consuming research challenge. Due to their exceptional characteristics, semiconducting metal oxides (SMOxs) have received a lot of attention in terms of the development of various types of sensors in recent years. The key performance indicators of SMOx-based sensors are their sensitivity, selectivity, recovery time, and steady response over time. SMOx-based sensors are discussed in this review based on their different properties. Surface properties of the functional material, such as its (nano)structure, morphology, and crystallinity, greatly influence sensor performance. A few examples of the complicated and poorly understood processes involved in SMOx sensing systems are adsorption and chemisorption, charge transfers, and oxygen migration. The future prospects of SMOx-based gas sensors, chemical sensors, and biological sensors are also discussed.

A highly selective and recyclable sensor for the electroanalysis of phosphothioate pesticides using silver-doped ZnO nanorods arrays

Silver-doped ZnO nanorods (Ag/ZnO) arrays have in-situ grown onto indium tin oxide (ITO) via the one-pot hydrothermal route towards a highly selective and recyclable electroanalysis of phosphothioate pesticides (PTs) with phoxim (Phox) as a model. It was discovered that the Ag/ZnO arrays-modified electrode could obtain a steady and sharp electrochemical output of solid-state Ag/AgCl at a low potential (i.e., 0.12 V). More importantly, the achieved Ag/AgCl signals could decrease selectively induced by sulfide (S)-containing Phox by the specific Cl-S displacement reaction, which would trigger AgCl into non-electroactive Ag-Phox complex. The Ag/ZnO arrays-modified sensors present a linear range from 0.050 to 700.0 μM for the detection of Phox, with a limit of detection down to 0.010 μM. The practical applicability of the developed electroanalysis strategy was successfully employed to detect Phox in the tap water and cabbage samples. Moreover, the photocatalytic performances of the Ag/ZnO arrays were subsequently verified for the degradation of Phox, displaying the higher photocatalytic efficiency than pure ZnO nanorods. Besides, the as-developed sensor can allow for the recyclable detection of Phox by the Ag/ZnO-photocatalyzed removal of Phox after each of the detection cycles. Therefore, the sensors platform based on Ag/ZnO arrays can be expected to have potential for the electrochemical monitoring and photocatalytic degradation of toxic pesticides in the food and environmental fields.

Construction of a novel electrochemical biosensor based on a mesoporous silica/oriented graphene oxide planar electrode for detecting hydrogen peroxide

A constant magnetic field (CMF) was used to arrange the orientation of graphene oxide (GO) which was modified on a self-made screen-printed electrode. We evaluated the efficiency of this method for potential analytical application towards the sensing of hydrogen peroxide (H2O2). Mesoporous silica (MS)-encapsulated horseradish peroxidase (HRP) was immobilized on the electrode with vertically arranged GO to construct an H2O2 sensor (denoted as CMF/GO/HRP@MS). The linear range of the response of the CMF/GO/HRP@MS sensor to H2O2 was 0.1-235 μM, and the detection limit was as low as 0.01 μM. The results demonstrated that the vertical arrangement of GO resulting from the CMF on the electrode surface could increase the electron transfer rate. The excellent selectivity and anti-interference ability of this sensor to H2O2 in physiological samples may be attributed to the synergistic effect of mesoporous silica, GO and constant magnetic field.

Synthesis of Ni2+ ion doped ZnO–MWCNTs nanocomposites using an in situ sol–gel method: an ultra sensitive non-enzymatic uric acid sensing electrode material

Nickel (Ni²⁺) ion doped zinc oxide-multi-wall carbon nanotubes (NZC) with different composition ratios of MWCNTs (from 0.01 to 0.1 wt%) are synthesized through an in situ sol–gel method. The synthesized NZC nanocomposites (NCs) are used as electrode materials with glassy carbon electrodes (GCEs) for electrochemical detection of uric acid (UA). The cyclic voltammogram of the representative NZC 0.1 modified GCE (NZC 0.1/GCE) revealed the highest electrochemical sensing activity towards the oxidation of UA at 0.37 V in 0.2 M phosphate buffer solution (PBS) having pH 7.4 ± 0.02. The limit of detection (LOD) and limit of quantification (LOQ) for the NZC 0.1/GCE are determined to be 5.72 nM and 19.00 nM (S/N = 3) respectively, which is the lowest compared to the literature values reported for enzymatic and non-enzymatic detection techniques. The synergistic effect of NZC 0.1 NCs is proposed as one of the factors for the enhanced electrochemical oxidation of UA complemented by the phase, lattice parameters, functional groups, morphology, elemental compositions, types of bonding and specific surface area with pore size ascertained using various techniques. The synthesized NZC 0.1 NCs are further proposed as selective electrode materials for the electrochemical detection of UA as authenticated further by performing interference tests with other metabolites such as ascorbic acid (AA), dopamine (DA) and d-glucose. The optimized electrochemical studies are further adopted for sensing of UA from human excretion samples using NZC 0.1 NCs.

Nickel (Ni²⁺) ion doped zinc oxide-multi-wall carbon nanotubes (NZC) with different composition ratios of MWCNTs (from 0.01 to 0.1 wt%) are synthesized through an in situ sol–gel method.

Fabrication and Characterization of Glucose Biosensors by Using Hydrothermally Grown ZnO Nanorods

Highly oriented ZnO nanorod (NR) arrays were fabricated on a seeded substrate through a hydrothermal route. The prepared ZnO nanorods were used as an amperometric enzyme electrode, in which glucose oxidase (GOx) was immobilised through physical adsorption. The modified electrode was designated as Nafion/GOx/ZnO NRs/ITO. The morphology and structural properties of the fabricated ZnO nanorods were analysed using field-emission scanning electron microscope and X-ray diffractometer. The electrochemical properties of the fabricated biosensor were studied by cyclic voltammetry and amperometry. Electrolyte pH, electrolyte temperature and enzyme concentration used for immobilisation were the examined parameters influencing enzyme activity and biosensor performance. The immobilised enzyme electrode showed good GOx retention activity. The amount of electroactive GOx was 7.82 × 10⁻⁸ mol/cm², which was relatively higher than previously reported values. The Nafion/GOx/ZnO NRs/ITO electrode also displayed a linear response to glucose ranging from 0.05 mM to 1 mM, with a sensitivity of 48.75 µA/mM and a low Michaelis–Menten constant of 0.34 mM. Thus, the modified electrode can be used as a highly sensitive third-generation glucose biosensor with high resistance against interfering species, such as ascorbic acid, uric acid and L-cysteine. The applicability of the modified electrode was tested using human blood samples. Results were comparable with those obtained using a standard glucometer, indicating the excellent performance of the modified electrode.

Biofunctionalized "Kiwifruit-Assembly" of Oxidoreductases in Mesoporous ZnO/Carbon Nanoparticles for Efficient Asymmetric Catalysis

A mesoporous ZnO/carbon composite is designed for coimmobilization of two oxidoreductases involving a novel "kiwifruit-assembly" pattern. The coimmobilization of (S)-carbonyl reductase II-glucose dehydrogenase on nanoparticles (SCRII-GDH_nano ) exhibits 40-50% higher specific activity than the free enzyme and significantly improves stabilities of enzymes to heat, pH and solvents. It performs asymmetric catalysis of 75 × 10^-3 m substrate with a perfect yield of 100% and an excellent enantioselectivity of 99.9% within 1 h. SCRII-GDH_nano gives an over 72% yield and 99.9% enantioselectivity after it is reused for ten times. Even with a highly concentrated (400 × 10^-3 m) substrate, it shows about 60% yield and 99.9% enantioselectivity within 4 h. SCRII-GDH_nano presents 4.5-8.0-fold higher productivity in 2.0-8.0-fold shorter reaction time than the free enzyme. This work provides a general, facile, and unique approach for the immobilization of two oxidoreductases and gives high catalytic efficiency, long-term and good recycling stabilities by triggering radical proton-coupled electron transfer.

Three-dimensional N-doped carbon nanotube@carbon foam hybrid: an effective carrier of enzymes for glucose biosensors

NCNTs anchored on carbon foam lead to an effective carrier of enzymes for biosensors.

Smart Nanocomposites of Cu-Hemin Metal-Organic Frameworks for Electrochemical Glucose Biosensing

Herein, a smart porous material, Cu-hemin metal-organic-frameworks (Cu-hemin MOFs), was synthesized via assembling of Cu²⁺ with hemin to load glucose oxidase (GOD) for electrochemical glucose biosensing for the first time. The formation of the Cu-hemin MOFs was verified by scanning electron microscopy, X-ray powder diffraction, Fourier transform infrared spectroscopy, N₂ adsorption/desorption isotherms, UV-vis absorption spectroscopy, fluorescence spectroscopy, thermal analysis and electrochemical techniques. The results indicated that the Cu-hemin MOFs showed a ball-flower-like hollow cage structure with a large specific surface area and a large number of mesopores. A large number of GOD molecules could be successfully loaded in the pores of Cu-hemin MOFs to keep their bioactivity just like in a solution. The GOD/Cu-hemin MOFs exhibited both good performance toward oxygen reduction reaction via Cu-hemin MOFs and catalytic oxidation of glucose via GOD, superior to other GOD/MOFs and GOD/nanomaterials. Accordingly, the performance of GOD/Cu-hemin MOFs-based electrochemical glucose sensor was enhanced greatly, showing a wide linear range from 9.10 μM to 36.0 mM and a low detection limit of 2.73 μM. Moreover, the sensor showed satisfactory results in detection of glucose in human serum. This work provides a practical design of new electrochemical sensing platform based on MOFs and biomolecules.

Fabrication and characterization of SiO2/Si heterogeneous nanopillar arrays

This work presents arrays of heterogeneous nanopillars stacked with Si bodies and SiO2 heads for biomedical applications. Novel crossed and overlapped spacer techniques are proposed to fabricate the nanopillar arrays in controllable dimensions. For the nanopillars in the arrays, the minimum spacing, body diameter and head tip-radius reach 100 nm, 23 nm and 11 nm, respectively. The maximum height is 1.2 μm. In addition, because of hydrophilic/hydrophobic selectivity between the SiO2 heads and Si bodies, localized nanoliter water-droplet condensing, fluorescein solution extraction and protein capturing are observed on the SiO2 pillar heads. These experiments demonstrate the great potential of heterogeneous nanopillars in biomedical applications.

Genetically Engineered Phage-Templated MnO2 Nanowires: Synthesis and Their Application in Electrochemical Glucose Biosensor Operated at Neutral pH Condition

To conveniently obtain one-dimensional MnO2 nanowires (NWs) with controlled structure and unique properties for electron transfer, the genetically engineered M13 phages were used as templates for precise nucleation and growth of MnO2 crystals in filamentous phage scaffolds, via the spontaneous oxidation of Mn(2+) in alkaline solution. It was found that the morphology of NWs could be tailored by the surface charge of M13 mutants. MnO2 crystals were uniformly distributed on the surface of negatively charged tetraglutamate-fused phage (M13-E4), significantly different from irregular MnO2 agglomeration on the weakly negatively charged wild-type phage and positively charged tetraarginine-fused phage. The as-synthesized M13-E4@MnO2 NWs could catalyze the electro-oxidation of H2O2 at neutral pH. To demonstrate the superiority of the electrocatalytic activity in the solution containing plenty of chloride ions at neutral pH, both glucose oxidase and as-prepared MnO2 NWs were used for fabricating the glucose biosensor. The proposed biosensor showed a wide linear range (5 μM to 2 mM glucose), a low limit of detection of 1.8 μM glucose (S/N = 3), good interassay and intra-assay reproducibility and satisfactory storage stability. Due to the superiorities of synthesis and electrochemical performance, the as-prepared MnO2 NWs are promising for applications in electrocatalysis, electrochemical sensor, and supercapacitor.

Plasmon-enhanced Electrically Light-emitting from ZnO Nanorod Arrays/p-GaN Heterostructure Devices

Effective and bright light-emitting-diodes (LEDs) have attracted broad interests in fundamental research and industrial application, especially on short wavelength LEDs. In this paper, a well aligned ZnO nanorod arrays grown on the p-GaN substrate to form a heterostructured light-emitting diode and Al nanoparticles (NPs) were decorated to improve the electroluminescence performance. More than 30-folds enhancement of the electroluminescence intensity was obtained compared with the device without Al NPs decoration. The investigation on the stable and transient photoluminescence spectraof the ZnO nanorod arrays before and after Al NPs decoration demonstrated that the metal surface plasmon resonance coupling with excitons of ZnO leads to the enhancement of the internal quantum efficiency (IQE). Our results provide aneffective approach to design novel optoelectronic devices such as light-emitting diodes and plasmonic nanolasers.

A general and rapid approach to hybrid metal nanoparticle–ZnO nanowire arrays and their use as active substrates for surface-enhanced Raman scattering detection

Rapid SERS substrate preparation: an aqueous phase reaction of metal precursors with ZnO@Zn has been exploited for synthesizing SERS-active metal–ZnO nanowire arrays.

Piezotronic-effect enhanced drug metabolism and sensing on a single ZnO nanowire surface with the presence of human cytochrome P450

Cytochromes P450 (CYPs) enzymes are involved in catalyzing the metabolism of various endogenous and exogenous compounds. A rapid analysis of drug metabolism reactions by CYPs is required because they can metabolize 95% of current drugs in drug development and effective therapies. Here, we describe a study of piezotronic-effect enhanced drug metabolism and sensing by utilizing a single ZnO nanowire (ZnO NW) device. Owing to the unique hydrophobic feature of a ZnO NW that provides a desirable "microenvironment" for the immobilization of biomolecules, our device can effectively stimulate the tolbutamide metabolism by decorating a ZnO NW with cytochrome P4502C9/CYPs reductase (CYP2C9/CPR) microsomes. By applying an external compressive strain to the ZnO nanowire, the piezotronic effect, which plays a primary role in tuning the transport behavior of a ZnO NW utilizing the created piezoelectric polarization charges at the local interface, can effectively enhance the performance of the device. A theoretical model is proposed using an energy band diagram to explain the experimental data. This study provides a potential approach to study drug metabolism and trace drug detection based on the piezotronic effect.

A comprehensive biosensor integrated with a ZnO nanorod FET array for selective detection of glucose, cholesterol and urea

A ZnO NR integrated FET array biosensor with immobilized enzymes.

A glucose biosensor based on glucose oxidase immobilized on three-dimensional porous carbon electrodes

A schematic illustration of a 3D-KSC/GOD glucose biosensor is presented.

A polyaniline microtube platform for direct electron transfer of glucose oxidase and biosensing applications

A polyaniline microtube platform was fabricated for direct electron transfer of glucose oxidase and biosensing applications.

Dopamine fluorescent sensors based on polypyrrole/graphene quantum dots core/shell hybrids

A facilely prepared fluorescent sensor was developed for dopamine (DA) detection with high sensitivity and selectivity based on polypyrrole/graphene quantum dots (PPy/GQDs) core/shell hybrids. The composites exhibit strong fluorescence emission, which is dramatically enhanced as high as three times than pristine GQDs. The prepared sensor allows a highly sensitive determination of DA by fluorescent intensity decreasing with the addition of DA and presents a good linearity in range of 5-8000 nM with the detection limit of 10 pM (S/N = 3). Furthermore, the application of the proposed approach have been demonstrated in real samples and showed promise in diagnostic purposes.

Fabrication of a novel microsensor consisting of electrodeposited ZnO nanorod-coated crossed Cu micropillars and the effects of nanorod coating morphology on the gas sensing

A novel microsensor, consisting of crossed Cu micropillars coated with ZnO nanorods, was fabricated by electrochemical methods for detecting gas in a small space. The Cu micropillars (80 μm diameter, 10 mm long) were prepared by microanode-guided electroplating (MAGE) on the periphery of a square copper pad (dimensions 5.0 mm × 5.0 mm × 1.0 mm). The micropillars were electrochemically coated with a 500 nm thick layer of ZnO nanorods deposited from a bath containing 2.0 mM zinc chloride and H2O2 varying in 5, 10, 15, and 20 mM. Two ZnO-coated pillars were crossed to form a microsensor by approaching the Cu pads below, which was adhered to an alumina substrate with silver paste and connected to conducting wires for measurement. The morphology of the coating of ZnO nanorods, which was found to be determined by the concentration of H2O2 in the bath, influenced the gas sensing. The morphology of the coating was characterized by scanning electron microscopy; the structural analysis was carried out by X-ray diffraction and high-resolution transmission electron microscopy (HRTEM); the surface analysis was carried out by X-ray photoelectron spectroscopy; and the defects were determined with photoluminescence (PL) spectra. We thus investigated the effect of the morphology of the coating on the sensing properties by introducing a stream of gases varying in CO/air ratios to understand the sensing mechanism of the microsensor.

Dye-sensitized solar cell from polyaniline–ZnS nanotubes and its characterization through impedance spectroscopy

DSSC fabricated with polyaniline–ZnS nanotubes exhibits reversible turn “on” and “off” capability with an efficiency of 3.4%, as shown by a Nyquist plot, characterizing different transport processes.

Recent advances in ZnO nanostructures and thin films for biosensor applications: review

Biosensors have shown great potential for health care and environmental monitoring. The performance of biosensors depends on their components, among which the matrix material, i.e., the layer between the recognition layer of biomolecule and transducer, plays a crucial role in defining the stability, sensitivity and shelf-life of a biosensor. Recently, zinc oxide (ZnO) nanostructures and thin films have attracted much interest as materials for biosensors due to their biocompatibility, chemical stability, high isoelectric point, electrochemical activity, high electron mobility, ease of synthesis by diverse methods and high surface-to-volume ratio. ZnO nanostructures have shown the binding of biomolecules in desired orientations with improved conformation and high biological activity, resulting in enhanced sensing characteristics. Furthermore, compatibility with complementary metal oxide semiconductor technology for constructing integrated circuits makes ZnO nanostructures suitable candidate for future small integrated biosensor devices. This review highlights recent advances in various approaches towards synthesis of ZnO nanostructures and thin films and their applications in biosensor technology.