Multi-membrane hydrogels

Development and Characterization of Heparin-Containing Hydrogel/3D-Printed Scaffold Composites for Craniofacial Reconstruction

Regeneration of cartilage and bone tissues remains challenging in tissue engineering due to their complex structures, and the need for both mechanical support and delivery of biological repair stimuli. Therefore, the goal of this study was to develop a composite scaffold platform for anatomic chondral and osteochondral repair using heparin-based hydrogels to deliver small molecules within 3D-printed porous scaffolds that provide structure, stiffness, and controlled biologic delivery. We designed a mold-injection system to combine hydrolytically degradable hydrogels and 3D-printed scaffolds that could be employed rapidly (< 30 min) in operating room settings (~23 °C). Micro-CT analysis demonstrated the effectiveness of our injection system through homogeneously distributed hydrogel within the pores of the scaffolds. Hydrogels and composite scaffolds exhibited efficient loading (~94%) of a small positively charged heparin-binding molecule (crystal violet) with sustained release over 14 days and showed high viability of encapsulated porcine chondrocytes over 7 days. Compression testing demonstrated nonlinear viscoelastic behavior where tangent stiffness decreased with scaffold porosity (porous scaffold tangent stiffness: 70%: 4.9 MPa, 80%: 1.5 MPa, and 90%: 0.20 MPa) but relaxation was not affected. Lower-porosity scaffolds (70%) showed stiffness similar to lower ranges of trabecular bone (4-8 MPa) while higher-porosity scaffolds (80% and 90%) showed stiffness similar to auricular cartilage (0.16-2 MPa). Ultimately, this rapid composite scaffold fabrication method may be employed in the operating room and utilized to control biologic delivery within load-bearing scaffolds.

FRESH-based 3D bioprinting of complex biological geometries using chitosan bioink

Traditional three-dimensional (3D) bioprinting has always been associated with the challenge of print fidelity of complex geometries due to the gel-like nature of the bioinks. Embedded 3D bioprinting has emerged as a potential solution to print complex geometries using proteins and polysaccharides-based bioinks. This study demonstrated the Freeform Reversible Embedding of Suspended Hydrogels (FRESH) 3D bioprinting method of chitosan bioink to 3D bioprint complex geometries. 4.5% chitosan was dissolved in an alkali solvent to prepare the bioink. Rheological evaluation of the bioink described its shear-thinning nature. The power law equation was fitted to the shear rate-viscosity plot. The flow index value was found to be less than 1, categorizing the material as pseudo-plastic. The chitosan bioink was extruded into another medium, a thermo-responsive 4.5% gelatin hydrogel. This hydrogel supports the growing print structures while printing. After this, the 3D bioprinted structure was crosslinked with hot water to stabilize the structure. Using this method, we have 3D bioprinted complex biological structures like the human tri-leaflet heart valve, a section of a human right coronary arterial tree, a scale-down outer structure of the human kidney, and a human ear. Additionally, we have shown the mechanical tunability and suturability of the 3D bioprinted structures. This study demonstrates the capability of the chitosan bioink and FRESH method for 3D bioprinting of complex biological models for biomedical applications.

Organized assembly of chitosan into mechanically strong bio-composite by introducing a recombinant insect structural protein OfCPH-1

Chitosan, known for its appealing biological properties in packaging and biomedical applications, faces challenges in achieving a well-organized crystalline structure for mechanical excellence under mild conditions. Herein, we propose a facile and mild bioengineering approach to induce organized assembly of amorphous chitosan into mechanically strong bio-composite via incorporating a genetically engineered insect structural protein, the cuticular protein hypothetical-1 from the Ostrinia furnacalis (OfCPH-1). OfCPH-1 exhibits high binding affinity to chitosan via hydrogen-bonding interactions. Simply mixing a small proportion (0.5 w/w%) of bioengineered OfCPH-1 protein with acidic chitosan precursor induces the amorphous chitosan chains to form fibrous networks with hydrated chitosan crystals, accompanied with a solution-to-gel transition. We deduce that the water shell destruction driven by strong protein-chitosan interactions, triggers the formation of well-organized crystalline chitosan, which therefore offers the chitosan with significantly enhanced swelling resistance, and strength and modulus that outperforms that of most reported chitosan-based materials as well as petroleum-based plastics. Moreover, the composite exhibits a stretch-strengthening behavior similar to the training living muscles on cyclic load. Our work provides a route for harnessing the OfCPH-1-chitosan interaction in order to form a high-performance, sustainably sourced bio-composite.

A universal solvent-replacement strategy to convert alginate hydrogels into mechanically strong and transparent alginate eutectogels for sensitive strain sensors

Eutectogels based on natural polymers have attracted significant attention as an alternative to easily dehydrated hydrogels and expensive ionogels in the development of flexible strain sensors. The feasibility of employing eutectogels derived from pure natural polymers could be greatly enhanced if their mechanical properties satisfy the requirements of applications. Herein, alginate eutectogels (AEs) with high mechanical properties (tensile strain 217 % and strength 2.26 MPa at fracture), and excellent transparency (over 90 %) are acquired via CaCl2 inducing ionic crosslinking and subsequent deep eutectic solvents (DESs, composed of glycerol and choline chloride) initiating physical crosslinking with a universal solvent- replacement strategy. Among them, sodium alginate, a natural polysaccharide polymer, is selected as representative supporting scaffolds and forms water-insoluble alginate hydrogels (AHs) in CaCl2 coagulation bath. The exchange of DESs with water of AHs not only restrengthens the polymer network by physical crosslinking, but also endows the obtained AEs with long-term solvent retention and high temperature resistance. In addition, the AEs not only have high reliability but also exhibit better linear sensitivity in a wide strain range (0-200 %). In particular, the AEs display multiple sensitivity to stretching, bending, and human motions, demonstrating feasibility as sensitive strain sensors.

Chitosan nanoparticle applications in dentistry: a sustainable biopolymer

The epoch of Nano-biomaterials and their application in the field of medicine and dentistry has been long-lived. The application of nanotechnology is extensively used in diagnosis and treatment aspects of oral diseases. The nanomaterials and its structures are being widely involved in the production of medicines and drugs used for the treatment of oral diseases like periodontitis, oral carcinoma, etc. and helps in maintaining the longevity of oral health. Chitosan is a naturally occurring biopolymer derived from chitin which is seen commonly in arthropods. Chitosan nanoparticles are the latest in the trend of nanoparticles used in dentistry and are becoming the most wanted biopolymer for use toward therapeutic interventions. Literature search has also shown that chitosan nanoparticles have anti-tumor effects. This review highlights the various aspects of chitosan nanoparticles and their implications in dentistry.

Practical Applications of Self-Healing Polymers Beyond Mechanical and Electrical Recovery

Self-healing polymeric materials, which can repair physical damage, offer promising prospects for protective applications across various industries. Although prolonged durability and resource conservation are key advantages, focusing solely on mechanical recovery may limit the market potential of these materials. The unique physical properties of self-healing polymers, such as interfacial reduction, seamless connection lines, temperature/pressure responses, and phase transitions, enable a multitude of innovative applications. In this perspective, the diverse applications of self-healing polymers beyond their traditional mechanical strength are emphasized and their potential in various sectors such as food packaging, damage-reporting, radiation shielding, acoustic conservation, biomedical monitoring, and tissue regeneration is explored. With regards to the commercialization challenges, including scalability, robustness, and performance degradation under extreme conditions, strategies to overcome these limitations and promote successful industrialization are discussed. Furthermore, the potential impacts of self-healing materials on future research directions, encompassing environmental sustainability, advanced computational techniques, integration with emerging technologies, and tailoring materials for specific applications are examined. This perspective aims to inspire interdisciplinary approaches and foster the adoption of self-healing materials in various real-life settings, ultimately contributing to the development of next-generation materials.

Polysaccharides as a promising platform for the treatment of spinal cord injury: A review

Spinal cord injury is incurable and often results in irreversible damage to motor function and autonomic sensory abilities. To enhance the effectiveness of therapeutic substances such as cells, growth factors, drugs, and nucleic acids for treating spinal cord injuries, as well as to reduce the toxic side effects of chemical reagents, polysaccharides have been gained attention due to their immunomodulatory properties and the biocompatibility and biodegradability of polysaccharide scaffolds. Polysaccharides hold potential as drug delivery systems in treating spinal cord injuries. This article aims to present an extensive evaluation of the potential applications of polysaccharide materials in scaffold construction, drug delivery, and immunomodulation over the past five years so that offering new directions and opportunities for the treatment of spinal cord injuries.

Subcutaneous Administration of a Zwitterionic Chitosan-Based Hydrogel for Controlled Spatiotemporal Release of Monoclonal Antibodies

Subcutaneous (SC) administration of monoclonal antibodies (mAbs) is a proven strategy for improving therapeutic outcomes and patient compliance. The current FDA-/EMA-approved enzymatic approach, utilizing recombinant human hyaluronidase (rHuPH20) to enhance mAbs SC delivery, involves degrading the extracellular matrix's hyaluronate to increase tissue permeability. However, this method lacks tunable release properties, requiring individual optimization for each mAb. Seeking alternatives, physical polysaccharide hydrogels emerge as promising candidates due to their tunable physicochemical and biodegradability features. Unfortunately, none have demonstrated simultaneous biocompatibility, biodegradability, and controlled release properties for large proteins (≥150 kDa) after SC delivery in clinical settings. Here, a novel two-component hydrogel comprising chitosan and chitosan@DOTAGA is introduced that can be seamlessly mixed with sterile mAbs formulations initially designed for intravenous (IV) administration, repurposing them as novel tunable SC formulations. Validated in mice and nonhuman primates (NHPs) with various mAbs, including trastuzumab and rituximab, the hydrogel exhibited biodegradability and biocompatibility features. Pharmacokinetic studies in both species demonstrated tunable controlled release, surpassing the capabilities of rHuPH20, with comparable parameters to the rHuPH20+mAbs formulation. These findings signify the potential for rapid translation to human applications, opening avenues for the clinical development of this novel SC biosimilar formulation.

Polysaccharides in contact lenses: From additives to bulk materials

As the number of applications has increased, so has the demand for contact lenses comfort. Adding polysaccharides to lenses is a popular way to enhance comfort for wearers. However, this may also compromise some lens properties. It is still unclear how to balance the variation of individual lens parameters in the design of contact lenses containing polysaccharides. This review provides a comprehensive overview of how polysaccharide addition impacts lens wear parameters, such as water content, oxygen permeability, surface wettability, protein deposition, and light transmittance. It also examines how various factors, such as polysaccharide type, molecular weight, amount, and mode of incorporation into lenses modulate these effects. Polysaccharide addition can improve some wear parameters while reducing others depending on the specific conditions. The optimal method, type, and amount of added polysaccharides depend on the trade-off between various lens parameters and wear requirements. Simultaneously, polysaccharide-based contact lenses may be a promising option for biodegradable contact lenses as concerns regarding environmental risks associated with contact lens degradation continue to increase. It is hoped that this review will shed light on the rational use of polysaccharides in contact lenses to make personalized lenses more accessible.

3D-Printed Chitosan-Based Hydrogels Loaded with Levofloxacin for Tissue Engineering Applications

Herein, we demonstrate the feasibility of a three-dimensional printed chitosan (CS)-poly(vinyl alcohol) (PVA)-gelatin (Gel) hydrogel incorporating the antimicrobial drug levofloxacin (LEV) as a potential tissue engineering scaffold. Hydrogels were prepared by physically cross-linking the polymers, and the printability of the prepared hydrogels was determined. The hydrogel with 3% w/v of CS, 3% w/v of PVA, and 2% w/v of Gel presented the best printability, producing smooth and uniform scaffolds. The integrity of 3D-printed scaffolds was improved via a neutralization process since after testing three different neutralized agents, i.e., NH3 vapors, EtOH/NaOH, and KOH solutions. It was proved that the CS/PVA/Gel hydrogel was formed by hydrogen bonds and remained amorphous in the 3D-printed structures. Drug loading studies confirmed the successful incorporation of LEV, and its in vitro release continued for 48 h. The cytotoxicity/cytocompatibility tests showed that all prepared scaffolds were cytocompatible.

Rapid fabrication of tough sodium alginate/MXene/poly(vinyl alcohol) dual-network hydrogel electrolytes for flexible all-solid-state supercapacitors

With the rapid development of flexible portable devices, polymer-based hydrogel electrolytes have drawn tremendous attention and widespread interest to replace conventional liquid electrolytes. Herein, an eco-friendly, low cost and fast method was adopted to synthesize novel cross-linked dual-network hydrogel electrolytes (PVA/SA/MXene-NaCl) within 5 min due to the formation of borate bonds. The unique dual-network structure of hydrogel enabled hydrogel electrolytes to efficiently dissipate energy under deformation and the formation of borate bonds endowed hydrogel with self-healing ability. Benefited from the introduction of NaCl and MXene, the hydrogels displayed a high ionic conductivity (40.8 mS/cm) and enhanced mechanical strength (650 kPa). Notedly, the flexible supercapacitor with low concentration of NaCl (0.3 mol L-1) delivered a superior areal capacitance of 130.8 mF cm-2 at 1 mA cm-2 and 106.2 mF cm-2 at 3 mA cm-2, and simultaneously offered remarkable capacitance retention under the state of bending, self-healing (five cycles), compression and stretching. Moreover, as-assembled supercapacitor maintained about 88.9 % of its original capacitance and 90.5 % of Coulombic efficiency after 5000 charge-discharge cycles. Our research presented a simple and universally pathway to prepare flexible energy storage devices with excellent mechanical and electrochemical properties.

High-tensile chitin films regenerated from cryogenic aqueous phosphoric acid

The abuse of non-renewable fossil resources and the resulting plastic pollution have posed a great burden on the environment. Fortunately, renewable bio-macromolecules have shown great potential to replace synthetic plastics in fields ranging from biomedical applications, and energy storage to flexible electronics. However, the potential of recalcitrant polysaccharides, such as chitin, in the above-mentioned fields have not been fully exploited because of its poor processability, which is ultimately due to the lack of suitable, economical, and environmentally friendly solvent for it. Herein, we demonstrate an efficient and stable strategy for the fabrication of high-strength chitin films from concentrated chitin solutions in cryogenic 85 wt% aqueous phosphoric acid (aq. H₃PO₄). The regeneration conditions, including the nature of the coagulation bath and its temperature are important variables affecting the reassembly of chitin molecules and hence the structure and micromorphology of the films. Uniaxial orientation of the chitin molecules by applying tension to the RCh hydrogels further endows the films with enhanced mechanical properties of up to 235 MPa and 6.7 GPa in tensile strength and Young's modulus, respectively.

Treatment of Periodontal Infections, the Possible Role of Hydrogels as Antibiotic Drug-Delivery Systems

With the advancement of biomedical research into antimicrobial treatments for various diseases, the source and delivery of antibiotics have attracted attention. In periodontal diseases, antibiotics are integral in positive treatment outcomes; however, the use of antibiotics is with caution as the potential for the emergence of resistant strains is of concern. Over the years, conventional routes of drug administration have been proven to be effective for the treatment of PD, yet the problem of antibiotic resistance to conventional therapies continues to remain a setback in future treatments. Hydrogels fabricated from natural and synthetic polymers have been extensively applied in biomedical sciences for the delivery of potent biological compounds. These polymeric materials either have intrinsic antibacterial properties or serve as good carriers for the delivery of antibacterial agents. The biocompatibility, low toxicity and biodegradability of some hydrogels have favoured their consideration as prospective carriers for antibacterial drug delivery in PD. This article reviews PD and its antibiotic treatment options, the role of bacteria in PD and the potential of hydrogels as antibacterial agents and for antibiotic drug delivery in PD. Finally, potential challenges and future directions of hydrogels for use in PD treatment and diagnosis are also highlighted.

Electro-Biofabrication. Coupling Electrochemical and Biomolecular Methods to Create Functional Bio-Based Hydrogels

Twenty years ago, this journal published a review entitled "Biofabrication with Chitosan" based on the observations that (i) chitosan could be electrodeposited using low voltage electrical inputs (typically less than 5 V) and (ii) the enzyme tyrosinase could be used to graft proteins (via accessible tyrosine residues) to chitosan. Here, we provide a progress report on the coupling of electronic inputs with advanced biological methods for the fabrication of biopolymer-based hydrogel films. In many cases, the initial observations of chitosan's electrodeposition have been extended and generalized: mechanisms have been established for the electrodeposition of various other biological polymers (proteins and polysaccharides), and electrodeposition has been shown to allow the precise control of the hydrogel's emergent microstructure. In addition, the use of biotechnological methods to confer function has been extended from tyrosinase conjugation to the use of protein engineering to create genetically fused assembly tags (short sequences of accessible amino acid residues) that facilitate the attachment of function-conferring proteins to electrodeposited films using alternative enzymes (e.g., transglutaminase), metal chelation, and electrochemically induced oxidative mechanisms. Over these 20 years, the contributions from numerous groups have also identified exciting opportunities. First, electrochemistry provides unique capabilities to impose chemical and electrical cues that can induce assembly while controlling the emergent microstructure. Second, it is clear that the detailed mechanisms of biopolymer self-assembly (i.e., chitosan gel formation) are far more complex than anticipated, and this provides a rich opportunity both for fundamental inquiry and for the creation of high performance and sustainable material systems. Third, the mild conditions used for electrodeposition allow cells to be co-deposited for the fabrication of living materials. Finally, the applications have been expanded from biosensing and lab-on-a-chip systems to bioelectronic and medical materials. We suggest that electro-biofabrication is poised to emerge as an enabling additive manufacturing method especially suited for life science applications and to bridge communication between our biological and technological worlds.

Hierarchical encapsulation of bacteria in functional hydrogel beads for inter- and intra- species communication

To sequester prokaryotic cells in a biofilm-like niche, the creation of a pertinent and reliable microenvironment that reflects the heterogeneous nature of biological systems is vital for sustenance. Design of a microenvironment that is conducive for growth and survival of organisms, should account for factors such as mass transport, porosity, stability, elasticity, size, functionality, and biochemical characteristics of the organisms in the confined architecture. In this work we present an artificial long-term confinement model fabricated by natural alginate hydrogels that are structurally stable and can host organisms for over 10 days in physiologically relevant conditions. A unique feature of the confinement platform is the development of stratified habitats wherein bacterial cells can be entrapped in the core as well as in the shell layers, wherein the thickness and the number of shell layers are tunable at fabrication. We show that the hydrogel microenvironment in the beads can host complex subpopulations of organisms similar to that in a biofilm. Dynamic interaction of bacterial colonies encapsulated in different beads or within the core and stratified layers of single beads was demonstrated to show intra- species communication. Inter- species communication between probiotic bacteria and human colorectal carcinoma cells was also demonstrated to highlight a possible bidirectional communication between the organisms in the beads and the environment. STATEMENT OF SIGNIFICANCE: Bacteria confinement in a natural soft hydrogel structure has always been a challenge due to the collapse of hydrogel architectures. Alternative methods have been attempted to encapsulate microorganisms by employing various processes to avoid/minimize rupturing of hydrogel structures. However, most of the past approaches have been unfavorable in balancing cell proliferation and functionality upon confinement. Our study addresses the fundamental gap in knowledge necessary to create favorable and complex 3D biofilm mimics utilizing natural hydrogel for microbial colonization for long-term studies. Our approach represents a cornerstone in the development of 3D functional architectures not only to advance studies in microbial communication, host-microbe interaction but also to address basic and fundamental questions in biology.

Review on Biomedical Advances of Hybrid Nanocomposite Biopolymeric Materials

Hybrid materials are classified as one of the most highly important topics that have been of great interest to many researchers in recent decades. There are many species that can fall under this category, one of the most important of which contain biopolymeric materials as a matrix and are additionally reinforced by different types of carbon sources. Such materials are characterized by many diverse properties in a variety industrial and applied fields but especially in the field of biomedical applications. The biopolymeric materials that fall under this label are divided into natural biopolymers, which include chitosan, cellulose, and gelatin, and industrial or synthetic polymers, which include polycaprolactone, polyurethane, and conducting polymers of variable chemical structures. Furthermore, there are many types of carbon nanomaterials that are used as enhancers in the chemical synthesis of these materials as reinforcement agents, which include carbon nanotubes, graphene, and fullerene. This research investigates natural biopolymers, which can be composed of carbon materials, and the educational and medical applications that have been developed for them in recent years. These applications include tissue engineering, scaffold bones, and drug delivery systems.

Hyaluronic acid and chitosan-based injectable and self-healing hydrogel with inherent antibacterial and antioxidant bioactivities

Injectable dressings offering intrinsic antibacterial activity and antioxidation are required, because persistent bacterial infection and oxidative damage are common issues associated with chronic non-healing wounds. Herein, a versatile QCS-l-TA-l-OHA hydrogel is fabricated using ubiquitous nature derived biological macromolecules, quaternized chitosan (QCS), tannic acid (TA) and oxidant hyaluronic acid (OHA), driving by multiple dynamic interactions under physiological conditions. The hydrogel can serve as multiple functional wound dress with injectable and self-healing capabilities coupling with attractive antibacterial activity and antioxidation. The biocompatible and self-biodegradable hydrogel augments free radical scavenging capacity, antibacterial, angiogenesis, mature granulation tissue and collagen disposition, enabling fast wound healing of rat skin full-thickness incision model. This study highlights a wound dressing platform of hyaluronic acid and chitosan based injectable and self-healing hydrogel with inherent antibacterial and antioxidant bioactivities, thereby avoiding the use of antibiotics or antioxidant agents.

Facile post-gelation soaking strategy toward low-alkaline konjac glucomannan gels

A facile post-gelation soaking strategy for producing low-alkaline konjac glucomannan (KGM) gels was investigated in this work. The dealkalization kinetics of soaking alkali-induced gels in citric acid (CA) solutions was determined. A comparison of sensory, textural, and water holding properties was made between untreated and post-soaking gels. Post-gelation exposure to acid took less time for lowering the gel pH at higher CA concentrations, eliminated the unattractive flavor of KGM gels and endowed them a higher hardness and breaking force. Comparatively, the whiteness of post-soaking gels was increased by 3.8%-13.1% with volume being decreased by 4.9%-8.6%, while the discrepancies were less apparent after a long-term storage. Low-alkaline gels treated by 4 g/L CA shared similar textural features with conventional KGM gels. Despite the difference in water distribution and water holding capacity of KGM gels, the syneresis of resultant low-alkaline KGM gels was not significantly affected.

A tough and mechanically stable adhesive hydrogel for non-invasive wound repair

Wound healing has been a great challenge throughout human history. Improper treatment for wounds is so easy to lead to infection and a series of serious symptoms, even death. Because of the ability of absorbing fluid and keeping a moist environment, the hydrogel with 3D networks is ideal candidate for wound dressing. More important, it has good biocompatibility. However, most of the hydrogel dressings reported have weak mechanical properties and adhesion properties, which greatly limit their clinical application. Herein, a tough adhesive hydrogel with good mechanical stability for non-invasive wound repair is reported. The hydrogel is composed of polyethylene glycol dimethacrylate (PEGDA), chitosan (CS) and chitin nano-whisker (CW). PEGDA and CS form interpenetrating network hydrogel through free radical polymerization reaction under the UV light. The introduction of CW further enhances the toughness of the hydrogel. The pH-sensitive CS can form adhesion to various materials through topological adhesion. As a wound closure repair material, PEGDA/CS/CW hydrogel not only has the characteristic of effectively closing the wound, defending against invading bacteria, and keeping the wound clean, but also has good tensile and mechanical stability, which is expected to realize the closure and repair of joints and other moving parts of the wound. This adhesive hydrogel is proven a promising material for wound closure repair.

Non-equilibrium Nanoassemblies Constructed by Confined Coordination on a Polymer Chain

Biological systems employ non-equilibrium self-assembly to create ordered nanoarchitectures with sophisticated functions. However, it is challenging to construct artificial non-equilibrium nanoassemblies due to lack of control over assembly dynamics and kinetics. Herein, we design a series of linear polymers with different side groups for further coordination-driven self-assembly based on shape-complementarity. Such a design introduces a main-chain confinement which effectively slows down the assembly process of side groups, thus allowing us to monitor the real-time evolution of lychee-like nanostructures. The function related to the non-equilibrium nature is further explored by performing photothermal conversion study. The ability to observe and capture non-equilibrium states in this supramolecular system will enhance our understanding of the thermodynamic and kinetic features as well as functions of living systems.

Alginate microfibers as therapeutic delivery scaffolds and tissue mimics

Alginate, a naturally occurring polysaccharide, has been widely used in cell encapsulation, 3D culture, cell therapy, tissue engineering, and regenerative medicine. Alginate's frequent use comes from its biocompatibility and ability to easily form hydrogel in a variety of forms (e.g. microcapsules, microfibers, and porous scaffolds), which can provide immunoprotection for cell therapy and mimic the extracellular matrix for tissue engineering. During the past 15 years, alginate hydrogel microfibers have attracted more and more attention due to its continuous thin tubular structures (diameter or shell thickness ⩽ 200 µm), high-density cell growth, high handleability and retrievability, and scalability. This review article provides a concise overview of alginate and its resultant hydrogel microfibers for the purpose of promoting multidisciplinary, collaborative, and convergent research in the field. It starts with a historical review of alginate as biomaterials and provides basics about alginate structure, properties, and mechanisms of hydrogel formation, followed by current challenges in effective cell delivery and functional tissue engineering. In particular, this work discusses how alginate microfiber technology could provide solutions to unmet needs with a focus on the current state of the art of alginate microfiber technology and its applications in 3D cell culture, cell delivery, and tissue engineering. At last, we discuss future directions in the perspective of alginate-based advanced technology development in biology and medicine.

Mechanically Robust Hydrogels Facilitating Bone Regeneration through Epigenetic Modulation

Development of artificial biomaterials by mimicking extracellular matrix of bone tissue is a promising strategy for bone regeneration. Hydrogel has emerged as a type of viable substitute, but its inhomogeneous networks and weak mechanics greatly impede clinical applications. Here, a dual crosslinked gelling system is developed with tunable architectures and mechanics to promote osteogenic capacity. Polyhedral oligomeric silsesquioxane (POSS) is designated as a rigid core surrounded by six disulfide-linked PEG shells and two 2-ureido-4[1H]-pyrimidinone (UPy) groups. Thiol-disulfide exchange is employed to fabricate chemical network because of the pH-responsive "on/off" function. While self-complementary UPy motif is capable of optimizing local microstructure to enhance mechanical properties. Taking the merits of biocompatibility and high-mechanics in periodontal ligament stem cells (PDLSCs) proliferation, attachment, and osteogenesis, hybrid hydrogel exhibits outstanding osteogenic potential both in vitro and in vivo. Importantly, it is the first time that a key epigenetic regulator of ten-eleven translocation 2 (Tet2) is discovered to significantly elevate the continuously active the WNT/β-catenin through Tet2/HDAC1/E-cadherin/β-catenin signaling cascade, thereby promoting PDLSCs osteogenesis. This work represents a general strategy to design the hydrogels with customized networks and biomimetic mechanics, and illustrates underlying osteogenic mechanisms that will extend the design rationales for high-functional biomaterials in tissue engineering.

Water Saturated with Pressurized CO2 as a Tool to Create Various 3D Morphologies of Composites Based on Chitosan and Copper Nanoparticles

Methods for creating various 3D morphologies of composites based on chitosan and copper nanoparticles stabilized by it in carbonic acid solutions formed under high pressure of saturating CO2 were developed. This work includes a comprehensive analysis of the regularities of copper nanoparticles stabilization and reduction with chitosan, studied by IR and UV-vis spectroscopies, XPS, TEM and rheology. Chitosan can partially reduce Cu2+ ions in aqueous solutions to small-sized, spherical copper nanoparticles with a low degree of polydispersity; the process is accompanied by the formation of an elastic polymer hydrogel. The resulting composites demonstrate antimicrobial activity against both fungi and bacteria. Exposing the hydrogels to the mixture of He or H2 gases and CO2 fluid under high pressure makes it possible to increase the porosity of hydrogels significantly, as well as decrease their pore size. Composite capsules show sufficient resistance to various conditions and reusable catalytic activity in the reduction of nitrobenzene to aniline reaction. The relative simplicity of the proposed method and at the same time its profound advantages (such as environmental friendliness, extra purity) indicate an interesting role of this study for various applications of materials based on chitosan and metals.

Oral delivery of curcumin via multi-bioresponsive polyvinyl alcohol and guar gum based double-membrane microgels for ulcerative colitis therapy

Anti-inflammatory drugs for ulcerative colitis (UC) treatment should specifically penetrate and accumulate in the colon tissue. Herein, a multi-bioresponsive anti-inflammatory drug (curcumin, CUR)-loaded heterogeneous double-membrane microgels (CUR@microgels) for oral administration was fabricated in this study, in which the inner core was derived from polyvinyl alcohol (PVA) and guar gum (GG) and the outer gel was decoration with alginate and chitosan by polyelectrolyte interactions. The structure and morphology of microgels were characterized. In vitro, the formulation exhibited good bio-responses at different pH conditions and sustained-release properties in simulated colon fluid with a drug-release rate of 84.6 % over 34 h. With the assistance of the outlayer gels, the microgels effectively delayed the premature drug release of CUR in the upper gastrointestinal tract. In vivo studies revealed that CUR@microgels specifically accumulated in the colon tissue for 24 h, which suggest that the interlayer gels were apt to reach colon lesion. As expected, the oral administration of microgels remarkably alleviated the symptoms of UC and protected the colon tissue in DSS-induced UC mice. The above results indicated that these facilely fabricated microgels which exhibited excellent biocompatibility and multi-bioresponsive drug release, had an apparent effect on the treatment of UC, which represents a promising drug delivery strategy for CUR in a clinical application.

Manufacturing and post-engineering strategies of hydrogel actuators and sensors: From materials to interfaces

Living bodies are made of numerous bio-sensors and actuators for perceiving external stimuli and making movement. Hydrogels have been considered as ideal candidates for manufacturing bio-sensors and actuators because of their excellent biocompatibility, similar mechanical and electrical properties to that of living organs. The key point of manufacturing hydrogel sensors/actuators is that the materials should not only possess excellent mechanical and electrical properties but also form effective interfacial connections with various substrates. Traditional hydrogel normally shows high electrical resistance (~ MΩ•cm) with limited mechanical strength (<1 MPa), and it is prone to fatigue fracture during continuous loading-unloading cycles. Just like iron should be toughened and hardened into steel, manufacturing and post-treatment processes are necessary for modifying hydrogels. Besides, advanced design and manufacturing strategies can build effective interfaces between sensors/actuators and other substrates, thus enhancing the desired mechanical and electrical performances. Although various literatures have reviewed the manufacture or modification of hydrogels, the summary regarding the post-treatment strategies and the creation of effective electrical and mechanically sustainable interfaces are still lacking. This paper aims at providing an overview of the following topics: (i) the manufacturing and post-engineering treatment of hydrogel sensors and actuators; (ii) the processes of creating sensor(actuator)-substrate interfaces; (iii) the development and innovation of hydrogel manufacturing and interface creation. In the first section, the manufacturing processes and the principles for post-engineering treatments are discussed, and some typical examples are also presented. In the second section, the studies of interfaces between hydrogels and various substrates are reviewed. Lastly, we summarize the current manufacturing processes of hydrogels, and provide potential perspectives for hydrogel manufacturing and post-treatment methods.

Multi-layered alginate hydrogel structures and bacteria encapsulation

We show the design and fabrication of finely tuned alginate core-shell capsules with precisely controllable core and hierarchical shell thickness at micron scale for scaleup for mass production. The method developed was used to encapsulate bacteria while maintaining morphology and mechanical stability of the bead without rupturing and cell leakage.

Valorisation of lemongrass essential oils onto chitosan-starch film for sustainable active packaging: Greatly enhanced antibacterial and antioxidant activity

To meet the global demand for sustainability aspects, the past few decades have witnessed magnificent evidence in the pursuit of sustainable active food packaging. As part of our contribution, herein, we explored the utilization of chitosan (Ch) modified with Dioscorea hispida (Dh) starch and incorporated with lemongrass essential oil (LO) as an attempt to obtain a novel active packaging formulation of Ch/Dh/LO in food. To obtain the optimum formulation of Ch/Dh/LO, 15 experiments were designed using the Box-Behnken design (BBD) with Ch (1-2% w/v), Dh starch (0.5-1.5% w/v) and LO (0.25-0.75% v/v) against E. coli, S. typhi, S. aureus and S. epidermidis bacteria. The presence of LO caused enhancements in physical, mechanical, and thermal stability, along with the antimicrobial, and antioxidant activity. Additionally, molecular docking and molecular dynamic (MD) simulations of the active compounds in LO against the active site of the FtsA enzyme were provided to unveil the mechanism of antibacterial action. Ultimately, this result suggests hydrogen bonds and hydrophobic interactions are involved between the active compounds in LO and FtsA enzymes. In general, this research provides valuable information that sheds light on the pivotal role of LO in enhancing the mechanical, thermal, and biological properties of sustainable active food packaging-based Ch film.

Chitosan-enhanced nonswelling hydrogel with stable mechanical properties for long-lasting underwater sensing

Existing anti-swelling hydrogels with poor mechanical strength restrict their underwater human monitoring as wearable electronic sensing equipment. Herein, a nonswelling double network (DN) hydrogel with strong self-recoverability (97.22%) was developed by adding chitosan (CS) to poly(acrylic acid-2-methoxyethyl acrylate)-Fe³⁺ [P(AA-MEA)-Fe] network. Owing to the introduction of CS, the hydrogel displayed excellent nonswelling properties under aqueous solutions (pH = 1, 4 and 7), physiological saline, seawater, dodecane, n-hexane and chloroform. Besides, CS improved mechanical properties of hydrogel through non-covalent network (large stretchability of 1199%, tensile strength of 0.462 MPa and toughness of 2.01 MJ/m³). Surprisingly, the hydrogel still reached the extensibility (1072%) and tensile stress (0.467 MPa) even after immersing in water for 7 days. Fabricating hydrogel as flexible strain sensor, periodic real-time signals of human movements (e.g., joint actions and electronic skin touching) were accurately monitored under the water and seawater. The nonswelling P(AA-MEA)-CS-Fe hydrogel shows huge potential in underwater sensing.

A smart microhydrogel membrane sensor realized by pipette tip

In this paper, we describe a simple and practical way to prepare hydrogel membranes in a conical channel (pipette tip). We used a pipette to create a gas pressure difference on both sides of the gel precursor, which drove the gel precursor to move in the pipette tip. During movement, the shape of the hydrogel precursor gradually becomes thinner as the radius of the tapered channel becomes larger. We use this principle to realize the highly controllable preparation of the hydrogel membrane structure (130 μm at its thinnest). Moreover, we fabricated a hydrogel membrane sensor in one step by implanting smart molecules in the hydrogel, which achieved rapid and sensitive detection of 0.5 μM-500 mM potassium ions. This method of preparing the hydrogel membrane sensor does not rely on professional membrane production equipment and complex molecular design processes, has high gel utilization and simple and controllable membrane thickness, and has a wide range of application value in the field of intelligent hydrogel-based analysis technology.

Chitosan-based double cross-linked ionic hydrogels as a strain and pressure sensor with broad strain-range and high sensitivity

A conductive hydrogel P(AAm-co-AA)/CS-Fe³⁺ with double cross-linked networks was fabricated using a one-step polymerization by UV irradiation and a soaking process in Fe(NO₃)₃ solution. In this hydrogel, the rigid chain of chitosan (CS) and the soft chain of copolymer P(AAm-co-AA) with acrylic acid (AA) and acrylamide (AAm) act as the backbone, among which large amounts of hydrogen bonds are formed by the amino, hydroxyl, and carboxyl groups on the two polymers. Ferric irons (Fe³⁺) are introduced and form coordination interactions with carboxyl and amino groups of the polymers. The double cross-linked interactions in the system can enhance the tensile strength and toughness of the hydrogel. Thus, the prepared P(AAm-co-AA)/CS-Fe³⁺ hybrid network hydrogel shows excellent mechanical properties in many aspects: a strength of up to 550 kPa, a broad strain-range up to 800%, fast self-recovery ability (30 min), and low hysteresis strain (<100%). The conductive hydrogel demonstrates high strain sensitivity (gauge factor (GF) = 6.6 at a strain of 700%) as a flexible sensor. Human movements (for example, finger bending, vocal cord vibration, and other human activities) can be sensitively detected using the P(AAm-co-AA)/CS-Fe³⁺ hydrogel sensor.

Combined use of chitosan-PGLA nerve grafts and bone marrow mononuclear cells to repair a 50-mm-long median nerve defect combined with an 80-mm-long ulnar nerve defect in the human upper arm

BACKGROUND

Severe peripheral nerve injury, especially the long-distance peripheral nerve defect caused severe functional disability to patients. And there is always a lack of effective and less side effects of repair methods for clinics. A case study was performed to observe the regenerative outcomes of the surgical repair of long-distance peripheral nerve defects in the upper arm with chitosan-poly(glycolide-co-lactide) (PGLA) nerve grafts combined with bone marrow mononuclear cells (BMMCs).

METHODS

The right upper arm of a 29-year-old woman was injured, leaving a 50-mm-long median nerve defect, an 80-mm-long ulnar nerve defect, and muscle and blood vessel disruptions. The nerve defects were repaired by implanting BMMC-containing chitosan-PGA nerve grafts on the 40th day after injury. A series of functional assessments were carried out from 2 weeks to 66 months after surgical repair. Sensory function was assessed by the pinprick test, two-point discrimination test and Semmes-Weinstein monofilament test. Motor function was evaluated by the range of motion of the wrist joint and muscle power. Autonomic function was monitored by laser-Doppler perfusion imaging (LDPI). Tissue morphology was observed through ultrasonic investigations.

RESULTS

No adverse events, such as infection, allergy, or rejection, caused by the treatment were detected during the follow-up period. Sensory and pinprick nociception in the affected thumb, index, and middle fingers were restored gradually from the 6th month after surgery. The monofilament tactile sensation was 0.4 g in the terminal finger pulp of the thumb and index finger, 2.0 g in the middle finger, and greater than 300 g in the ring finger and little finger at the 66th month. Motor function recovery was detected at the 5th month after surgery, when the muscle strength of the affected forearm flexors began to recover. At the 66th month after surgery, the patient's forearm flexor strength was grade 4, with 80° of palmar flexion, 85° of dorsal extension, 8° of radial deviation, 40° of ulnar deviation, 40° of anterior rotation, and 85° of posterior rotation of the affected wrist. The patient could perform holding, picking up, and some other daily activities with the affected hand. The patient's sweating function of the affected hand was close to the level of the healthy hand. LDPI showed that the skin blood flow perfusion was significantly increased, with perfusion similar to on the normal side in some areas. Neuromusculoskeletal ultrasonography showed the presence of nerve structures.

CONCLUSIONS

These results suggest that chitosan-PGLA nerve grafts combined with BMMCs could effectively repair long-distance nerve defects and achieve good clinical results.

Self-Evolution of High Mechanical Strength Dry-Network Polythiourethane Thermosets into Neat Macroscopic Hollow Structures

Organism-inspired hollow structures are attracting increasing interest for the construction of various bionic functional hollow materials. Next-generation self-evolution hollow materials tend to combine simple synthesis, high mechanical strength, and regular shape. In this study, we designed and synthesized a novel dry-network polythiourethane thermoset with excellent mechanical performance. The polymer film could evolve into a neat and well-organized object with a macroscopic hollow interior structure after being immersed in an aqueous NaOH solution. The self-evolution hollow structure originated from a hydrogen-bonded polymer network, which was later transformed into a network bearing both hydrogen bonds and ionic bonds. The swelling and thickness growth of this material could be controlled by the NaOH concentration and the immersion time. This unique self-evolution behavior was further utilized to produce a series of macroscopic 3D hollow-containing molds, which could be potentially applied in the production of smart materials.

Fabrication and characterization of a toughened spherical chitosan adsorbent only through physical crosslinking based on mechanism of Chain Rearrangement

Chitosan extracted from natural products has gained tremendous attention in the field of adsorption and separation due to its inherent biocompatibility and potential applications. In this research, we synthesized a new type of spherical chitosan adsorbent (SCA) by controlling the mass transfer rate of the entanglement of the polymer chains in the recombination process. This SCA is a highly crystalline polymer material with outstanding mechanical strength, high adsorption capacity, a porous surface and suitable particle size distribution. The value of the sphericity of attrition of this SCA was 89.8%, which is the same as that of the commercial macroporous resin with a polystyrene matrix. The X-ray diffraction (XRD) patterns and differential scanning calorimetry (DSC) curves showed a significant change from powder to spherical structure and confirmed that the SCA is highly ordered and crystalline. Optical microscopy (OM) and scanning electron microscopy (SEM) demonstrated that the SCA was composed of a tightly stacked fiber structure, indicating the homogeneity of the polymerization. The porous structure of the surface provided a channel for mass transfer, which was indicated by a test of the ion exchange capacity and the adsorption performance of the SCA with Cu(ii) as the adsorbed subject. The adsorption capacity was higher than those of all reported non-composite chitosan materials. Therefore, we have successfully synthesized a completely green, nontoxic and environmentally friendly adsorbing resin equipped with excellent mechanical properties and adsorption capacity for future applications in many new fields.

Polymer Encapsulation of Bacterial Biosensors Enables Coculture with Mammalian Cells

Coexistence of different populations of cells and isolation of tasks can provide enhanced robustness and adaptability or impart new functionalities to a culture. However, generating stable cocultures involving cells with vastly different growth rates can be challenging. To address this, we developed living analytics in a multilayer polymer shell (LAMPS), an encapsulation method that facilitates the coculture of mammalian and bacterial cells. We leverage LAMPS to preprogram a separation of tasks within the coculture: growth and therapeutic protein production by the mammalian cells and l-lactate biosensing by Escherichia coli encapsulated within LAMPS. LAMPS enable the formation of a synthetic bacterial-mammalian cell interaction that enables a living biosensor to be integrated into a biomanufacturing process. Our work serves as a proof-of-concept for further applications in bioprocessing since LAMPS combine the simplicity and flexibility of a bacterial biosensor with a viable method to prevent runaway growth that would disturb mammalian cell physiology.

One-step programmable electrofabrication of chitosan asymmetric hydrogels with 3D shape deformation

Programmable asymmetric hydrogels with tunable structure/shape or physical/chemical properties in response to external stimuli show particular significance in smart systems, but there is lack of simple, rapid, and cheap strategy to design such hydrogel systems. Herein, we report a one-step electrodeposition method to construct chitosan asymmetric hydrogels with tunable thickness and pore size that can be conveniently modulated by the process parameters. Our approach greatly simplifies the process of hydrogel preparation with complex shapes and asymmetric structure organization. The formation mechanism of asymmetric structure has been proposed, based on gelation behavior and entanglement of chitosan chains in the hydrogel-solution system under the electric field. By changing the shape of the electrodes, hydrogels with the morphology of strip, tube, flower, etc. can be obtained precisely and conveniently. They can perform programmable 2D to 3D smart dynamic deformation under pH and metal ions stimulation, indicating the broad application potential in soft robot and biosensor areas.

Robust, anti-freezing and conductive bonding of chitosan-based double-network hydrogels for stable-performance flexible electronic

Unstable hydrogel-substrate interfaces and defunctionalization at low temperature severely restrict versatile applications of hydrogel-based systems. Herein, various chitosan-polyacrylamide double-network (CS-PAM DN) ionic hydrogels were chemically linked with diverse substrates to construct robust and anti-freezing hydrogel-substrate combination, wherein the destructible CS physical network rendered effective energy dissipation mechanism to significantly enhanced the cohesion of hydrogels and the covalent linkage between PAM network with substrate surface strongly improved the interfacial adhesion. The synergistic effects enabled the CS-PAM DN hydrogels to be tightly bonded on diverse metals and inorganics. Impressively, the hydrogel-substrate combinations were freezing tolerant to well-maintain high interfacial toughness at low temperature. Notably, due to the high toughness and conductivity of hydrogel-metal interface, the hydrogel-metal combination can be utilized as a multi-model flexible sensor to detect strain and pressure within broad temperature range. This work may provide a platform for construction and emerging application of robust, anti-freezing and stable-performance hydrogel-based systems.

Cooperative assembly of redistributed arylgermanium-bearing alkoxysilanes in a mesostructured siloxane network

Three redistributed arylgermanium-bearing mono-, bis- and tris-triethoxysilyl arms were designed, cocondensed with TEOS to access SBA-15-type materials and embedded in chitosan to prepare functional bioplastics.