Operando spectroscopy study of the carbon dioxide electro-reduction by iron species on nitrogen-doped carbon

Vanadium as a Ti-like mediator boosting electronic transmission in Fe-based MOFs for photocatalytic sterilization

Efficient metal-organic frameworks (MOFs) photocatalytic bactericidal catalysts are urgently needed in water purification. Herein, a Fe-MOF (MIL-88B-NH2(V1Fe5) with promoted electron transport was achieved by vanadium (V) ions doping and V/Fe ratio optimization, showing excellent photocatalytic bactericidal activity againstE. coliunder visible light irradiation (99.92%). The efficient antibacterial mechanism, V as a Ti-like mediator boosting electronic transmission in MIL-88B-NH2(V1Fe5), was revealed by its band structure, transient photocurrent, electrochemical impedance spectroscopy, and scavenger quenching experiments. The enhancement of photocatalytic bactericidal performance of Fe-MOFs by V-ion-doping was confirmed by two other Fe-MOFs, MIL-53-NH2(V1Fe5) and MIL-101-NH2(V1Fe5), with the same metal ions and ligands, both of which have higher performance than the corresponding undoped MOFs. Among them, MIL-88B-NH2(V1Fe5) exhibits the highest photocatalytic bactericidal activity due to its suitable metal clusters ([M(μ3-O)] cluster) and topological structure (three-dimensional rhomboid network structure). This work demonstrated the amplification effect of V ion doping on electron transport in Fe-MOFs photocatalysts.

Synergizing Fe2O3 Nanoparticles on Single Atom Fe-N-C for Nitrate Reduction to Ammonia at Industrial Current Densities

The electrochemical reduction of nitrates (NO3 -) enables a pathway for the carbon neutral synthesis of ammonia (NH3), via the nitrate reduction reaction (NO3RR), which has been demonstrated at high selectivity. However, to make NH3 synthesis cost-competitive with current technologies, high NH3 partial current densities (jNH3) must be achieved to reduce the levelized cost of NH3. Here, the high NO3RR activity of Fe-based materials is leveraged to synthesize a novel active particle-active support system with Fe2O3 nanoparticles supported on atomically dispersed Fe-N-C. The optimized 3×Fe2O3/Fe-N-C catalyst demonstrates an ultrahigh NO3RR activity, reaching a maximum jNH3 of 1.95 A cm-2 at a Faradaic efficiency (FE) for NH3 of 100% and an NH3 yield rate over 9 mmol hr-1 cm-2. Operando XANES and post-mortem XPS reveal the importance of a pre-reduction activation step, reducing the surface Fe2O3 (Fe3+) to highly active Fe0 sites, which are maintained during electrolysis. Durability studies demonstrate the robustness of both the Fe2O3 particles and Fe-Nx sites at highly cathodic potentials, maintaining a current of -1.3 A cm-2 over 24 hours. This work exhibits an effective and durable active particle-active support system enhancing the performance of the NO3RR, enabling industrially relevant current densities and near 100% selectivity.

Revealing the structure of the active sites for the electrocatalytic CO2 reduction to CO over Co single atom catalysts using operando XANES and machine learning

Transition-metal nitrogen-doped carbons (TM-N-C) are emerging as a highly promising catalyst class for several important electrocatalytic processes, including the electrocatalytic CO2 reduction reaction (CO2RR). The unique local environment around the singly dispersed metal site in TM-N-C catalysts is likely to be responsible for their catalytic properties, which differ significantly from those of bulk or nanostructured catalysts. However, the identification of the actual working structure of the main active units in TM-N-C remains a challenging task due to the fluctional, dynamic nature of these catalysts, and scarcity of experimental techniques that could probe the structure of these materials under realistic working conditions. This issue is addressed in this work and the local atomistic and electronic structure of the metal site in a Co-N-C catalyst for CO2RR is investigated by employing time-resolved operando X-ray absorption spectroscopy (XAS) combined with advanced data analysis techniques. This multi-step approach, based on principal component analysis, spectral decomposition and supervised machine learning methods, allows the contributions of several co-existing species in the working Co-N-C catalysts to be decoupled, and their XAS spectra deciphered, paving the way for understanding the CO2RR mechanisms in the Co-N-C catalysts, and further optimization of this class of electrocatalytic systems.

Interrogation of 3d Transition Bimetallic Nanocrystal Nucleation and Growth Using In Situ Electron Microscope and Synchrotron X-ray Techniques

Understanding the nucleation and growth mechanism of 3d transition bimetallic nanocrystals (NCs) is crucial to developing NCs with tailored nanostructures and properties. However, it remains a significant challenge due to the complexity of 3d bimetallic NCs formation and their sensitivity to oxygen. Here, by combining in situ electron microscopy and synchrotron X-ray techniques, we elucidate the nucleation and growth pathways of Fe-Ni NCs. Interestingly, the formation of Fe-Ni NCs emerges from the assimilation of Fe into Ni clusters together with the reduction of Fe-Ni oxides. Subsequently, these NCs undergo solid-state phase transitions, resulting in two distinct solid solutions, ultimately dominated by γ-Fe3Ni2. Furthermore, we deconvolve the interplays between local coordination and electronic state concerning the growth temperature. We directly visualize the oxidation-state distributions of Fe and Ni at the nanoscale and investigate their changes. This work may reshape and enhance the understanding of nucleation and growth in atomic crystallization.

Amine-Functionalized Metal-Free Nanocarbon to Boost Selective CO2 Electroreduction to CO in a Flow Cell

Highly efficient electrochemical CO2-to-CO conversion is a promising approach for achieving carbon neutrality. While nonmetallic carbon electrocatalysts have shown potential for CO2-to-CO utilization in H-type cells, achieving efficient conversion in flow cells at an industrial scale remains challenging. In this study, we present a cost-effective synthesis strategy for preparing ultrathin 2D carbon nanosheet catalysts through simple amine functionalization. The optimized catalyst, NCNs-2.5, demonstrates exceptional CO selectivity with a maximum Faradaic efficiency of 98% and achieves a high current density of 55 mA cm-2 in a flow cell. Furthermore, the catalyst exhibits excellent long-term stability, operating continuously for 50 h while maintaining a CO selectivity above 90%. The superior catalytic activity of NCNs-2.5 is attributed to the presence of amine-N active sites within the carbon lattice structure. This work establishes a foundation for the rational design of cost-effective nonmetallic carbon catalysts as sustainable alternatives to metals in energy conversion systems.

Catalysis for Carbon-Circularity: Emerging Concepts and Role of Inorganic Chemistry

Carbon circularity is crucial for achieving a circular economy but has wider implications and impacts with respect to the circularity of materials. It has an in-depth transformative effect on the economy. CO2 recycling is a critical component for this objective, with catalysis and inorganic chemistry playing a determining role in achieving this challenge. This concept paper presents some examples, as food for thought, of unconventional aspects in developing thermal and electro/photocatalysts for recycling CO2. The aspects discussed regard designing novel materials for CO2 thermo- or electro-conversion and developing novel nanostructured electrodes.

Atomically Dispersed Metal Catalysts for the Conversion of CO2 into High-Value C2+ Chemicals

The conversion of carbon dioxide (CO2) into value-added chemicals with two or more carbons (C2+) is a promising strategy that cannot only mitigate anthropogenic CO2 emissions but also reduce the excessive dependence on fossil feedstocks. In recent years, atomically dispersed metal catalysts (ADCs), including single-atom catalysts (SACs), dual-atom catalysts (DACs), and single-cluster catalysts (SCCs), emerged as attractive candidates for CO2 fixation reactions due to their unique properties, such as the maximum utilization of active sites, tunable electronic structure, the efficient elucidation of catalytic mechanism, etc. This review provides an overview of significant progress in the synthesis and characterization of ADCs utilized in photocatalytic, electrocatalytic, and thermocatalytic conversion of CO2 toward high-value C2+ compounds. To provide insights for designing efficient ADCs toward the C2+ chemical synthesis originating from CO2, the key factors that influence the catalytic activity and selectivity are highlighted. Finally, the relevant challenges and opportunities are discussed to inspire new ideas for the generation of CO2-based C2+ products over ADCs.

Atomic Valence Reversal-Induced Polarization Resonance Spurs Highly Efficient Electromagnetic Wave Absorption in α-Fe2O3@Carbon Microtubes

Variegation and complexity of polarization relaxation loss in many heterostructured materials provide available mechanisms to seek a strong electromagnetic wave (EMW) absorption performance. Here we construct a unique heterostructured compound that bonds α-Fe2O3 nanosheets of the (110) plane on carbon microtubes (CMTs). Through effective alignment between the Fermi energy level of CMTs and the conduction band position of α-Fe2O3 nanosheets at the interface, we attain substantial polarization relaxation loss via novel atomic valence reversal between Fe(III) ↔ Fe(III-) induced with periodic electron injection from conductive CMTs under EMW irradiation to give α-Fe2O3 nanosheets. Such heterostructured materials possess currently reported minimum reflection loss of -84.01 dB centered at 10.99 GHz at a thickness of 3.19 mm and an effective absorption bandwidth (reflection loss ≤ -10 dB) of 7.17 GHz (10.83-18 GHz) at 2.65 mm. This work provides an effective strategy for designing strong EMW absorbers by combining highly efficient electron injection and atomic valence reversal.

Continuously Producing Highly Concentrated and Pure Acetic Acid Aqueous Solution via Direct Electroreduction of CO2

It is crucial to achieve continuous production of highly concentrated and pure C2 chemicals through the electrochemical CO2 reduction reaction (eCO2RR) for artificial carbon cycling, yet it has remained unattainable until now. Despite one-pot tandem catalysis (dividing the eCO2RR to C2 into two catalytical reactions of CO2 to CO and CO to C2) offering the potential for significantly enhancing reaction efficiency, its mechanism remains unclear and its performance is unsatisfactory. Herein, we selected different CO2-to-CO catalysts and CO-to-acetate catalysts to construct several tandem catalytic systems for the eCO2RR to acetic acid. Among them, a tandem catalytic system comprising a covalent organic framework (PcNi-DMTP) and a metal-organic framework (MAF-2) as CO2-to-CO and CO-to-acetate catalysts, respectively, exhibited a faradaic efficiency of 51.2% with a current density of 410 mA cm-2 and an ultrahigh acetate yield rate of 2.72 mmol m-2 s-1 under neutral conditions. After electrolysis for 200 h, 1 cm-2 working electrode can continuously produce 20 mM acetic acid aqueous solution with a relative purity of 95+%. Comprehensive studies revealed that the performance of tandem catalysts is influenced not only by the CO supply-demand relationship and electron competition between the two catalytic processes in the one-pot tandem system but also by the performance of the CO-to-C2 catalyst under diluted CO conditions.

Reversible Structural Evolution of Metal-Nitrogen-Doped Carbon Catalysts During CO2 Electroreduction: An Operando X-ray Absorption Spectroscopy Study

Electrochemical CO2 reduction (CO2 RR) is a rising technology, aiming to reduce the energy sector dependence on fossil fuels and to produce carbon-neutral raw materials. Metal-nitrogen-doped carbons (M-N-C) are emerging, cost-effective catalysts for this reaction; however, their long-term stability is a major issue. To overcome this, understanding their structural evolution is crucial, requiring systematic in-depth operando studies. Here a series of M-N-C catalysts (M = Fe, Sn, Cu, Co, Ni, Zn) is investigated using operando X-ray absorption spectroscopy. It is found that the Fe-N-C and Sn-N-C are prone to oxide clusters formation even before CO2 RR. In contrast, the respective metal cations are singly dispersed in the as-prepared Cu-N-C, Co-N-C, Ni-N-C, and (Zn)-N-C. During CO2 RR, metallic clusters/nanoparticles reversibly formed in all catalysts, except for the Ni-N-C. This phenomenon, previously observed only in Cu-N-C, thus is ubiquitous in M-N-C catalysts. The competition between M-O and M-N interactions is an important factor determining the mobility of metal species in M-N-C. Specifically, the strong interaction between the Ni centers and the N-functional groups of the carbon support results in higher stability of the Ni single-sites, leading to the excellent performance of Ni-N-C in the CO2 to CO conversion, in comparison to other transition metals.

Promoting CO2 Electroreduction to Acetate by an Amine-Terminal, Dendrimer-Functionalized Cu Catalyst

Acetate derived from electrocatalytic CO2 reduction represents a potential low-carbon synthesis approach. However, the CO2-to-acetate activity and selectivity are largely inhibited by the low surface coverage of in situ generated *CO, as well as the inefficient ethenone intermediate formation due to the side reaction between CO2 and alkaline electrolytes. Tuning catalyst microenvironments by chemical modification of the catalyst surface is a potential strategy to enhance CO2 capture and increase local *CO concentrations, while it also increases the selectivity of side reduction products, such as methane or ethylene. To solve this challenge, herein, we developed a hydrophilic amine-tailed, dendrimer network with enhanced *CO intermediate coverage on Cu catalytic sites while at the same time retaining the in situ generated OH- as a high local pH environment that favors the ethenone intermediate toward acetate. The optimized amine-network coordinated Cu catalyst (G3-NH2/Cu) exhibits one of the highest CO2-to-acetate Faradaic efficiencies of 47.0% with a partial current density of 202 mA cm-2 at -0.97 V versus the reversible hydrogen electrode.

Multiscale CO2 Electrocatalysis to C2+ Products: Reaction Mechanisms, Catalyst Design, and Device Fabrication

Electrosynthesis of value-added chemicals, directly from CO2, could foster achievement of carbon neutral through an alternative electrical approach to the energy-intensive thermochemical industry for carbon utilization. Progress in this area, based on electrogeneration of multicarbon products through CO2 electroreduction, however, lags far behind that for C1 products. Reaction routes are complicated and kinetics are slow with scale up to the high levels required for commercialization, posing significant problems. In this review, we identify and summarize state-of-art progress in multicarbon synthesis with a multiscale perspective and discuss current hurdles to be resolved for multicarbon generation from CO2 reduction including atomistic mechanisms, nanoscale electrocatalysts, microscale electrodes, and macroscale electrolyzers with guidelines for future research. The review ends with a cross-scale perspective that links discrepancies between different approaches with extensions to performance and stability issues that arise from extensions to an industrial environment.

An orientated mass transfer in Ni-Cu tandem nanofibers for highly selective reduction of CO2 to ethanol

Electrochemically reducing CO2 to ethanol is attractive but suffers from poor selectivity. Tandem catalysis that integrates the activation of CO2 to an intermediate using one active site and the subsequent formation of hydrocarbons on the other site offers a promising approach, where the control of the intermediate transfer between different catalytic sites is challenging. We propose an internally self-feeding mechanism that relies on the orientation of the mass transfer in a hierarchical structure and demonstrate it using a one-dimensional (1D) tandem core-shell catalyst. Specifically, the carbon-coated Ni-core (Ni/C) catalyzes the transformation of CO2-to-CO, after which the CO intermediates are guided to diffuse to the carbon-coated Cu-shell (Cu/C) and experience the selective reduction to ethanol, realizing the orientated key intermediate transfer. Results show that the Faradaic efficiency for ethanol was 18.2% at -1 V vs. RHE (VRHE) for up to 100 h. The following mechanism study supports the hypothesis that the CO2 reduction on Ni/C generates CO, which is further reduced to ethanol on Cu/C sites. Density functional theory calculations suggest a combined effect of the availability of CO intermediate in Ni/C core and the dimerization of key *CO intermediates, as well as the subsequent proton-electron transfer process on the Cu/C shell.

Promote electroreduction of CO2 via catalyst valence state manipulation by surface-capping ligand

Electrochemical CO2 reduction provides a potential means for synthesizing value-added chemicals over the near equilibrium potential regime, i.e., formate production on Pd-based catalysts. However, the activity of Pd catalysts has been largely plagued by the potential-depended deactivation pathways (e.g., [Formula: see text]-PdH to [Formula: see text]-PdH phase transition, CO poisoning), limiting the formate production to a narrow potential window of 0 V to -0.25 V vs. reversible hydrogen electrode (RHE). Herein, we discovered that the Pd surface capped with polyvinylpyrrolidone (PVP) ligand exhibits effective resistance to the potential-depended deactivations and can catalyze formate production at a much extended potential window (beyond -0.7 V vs. RHE) with significantly improved activity (~14-times enhancement at -0.4 V vs. RHE) compared to that of the pristine Pd surface. Combined results from physical and electrochemical characterizations, kinetic analysis, and first-principle simulations suggest that the PVP capping ligand can effectively stabilize the high-valence-state Pd species (Pdδ+) resulted from the catalyst synthesis and pretreatments, and these Pdδ+ species are responsible for the inhibited phase transition from [Formula: see text]-PdH to [Formula: see text]-PdH, and the suppression of CO and H2 formation. The present study confers a desired catalyst design principle, introducing positive charges into Pd-based electrocatalyst to enable efficient and stable CO2 to formate conversion.

Interfacial Chemistry in the Electrocatalytic Hydrogenation of CO2 over C-Supported Cu-Based Systems

Operando soft and hard X-ray spectroscopic techniques were used in combination with plane-wave density functional theory (DFT) simulations to rationalize the enhanced activities of Zn-containing Cu nanostructured electrocatalysts in the electrocatalytic CO2 hydrogenation reaction. We show that at a potential for CO2 hydrogenation, Zn is alloyed with Cu in the bulk of the nanoparticles with no metallic Zn segregated; at the interface, low reducible Cu(I)-O species are consumed. Additional spectroscopic features are observed, which are identified as various surface Cu(I) ligated species; these respond to the potential, revealing characteristic interfacial dynamics. Similar behavior was observed for the Fe-Cu system in its active state, confirming the general validity of this mechanism; however, the performance of this system deteriorates after successive applied cathodic potentials, as the hydrogen evolution reaction then becomes the main reaction pathway. In contrast to an active system, Cu(I)-O is now consumed at cathodic potentials and not reversibly reformed when the voltage is allowed to equilibrate at the open-circuit voltage; rather, only the oxidation to Cu(II) is observed. We show that the Cu-Zn system represents the optimal active ensembles with stabilized Cu(I)-O; DFT simulations rationalize this observation by indicating that Cu-Zn-O neighboring atoms are able to activate CO2, whereas Cu-Cu sites provide the supply of H atoms for the hydrogenation reaction. Our results demonstrate an electronic effect exerted by the heterometal, which depends on its intimate distribution within the Cu phase and confirms the general validity of these mechanistic insights for future electrocatalyst design strategies.

Ce Site in Amorphous Iron Oxyhydroxide Nanosheet toward Enhanced Electrochemical Water Oxidation

Iron oxyhydroxide has been considered an auspicious electrocatalyst for the oxygen evolution reaction (OER) in alkaline water electrolysis due to its suitable electronic structure and abundant reserves. However, Fe-based materials seriously suffer from the tradeoff between activity and stability at a high current density above 100 mA cm^-2 . In this work, the Ce atom is introduced into the amorphous iron oxyhydroxide (i.e., CeFeO_x H_y ) nanosheet to simultaneously improve the intrinsic electrocatalytic activity and stability for OER through regulating the redox property of iron oxyhydroxide. In particular, the Ce substitution leads to the distorted octahedral crystal structure of CeFeO_x H_y , along with a regulated coordination site. The CeFeO_x H_y electrode exhibits a low overpotential of 250 mV at 100 mA cm^-2 with a small Tafel slope of 35.1 mVdec^-1 . Moreover, the CeFeO_x H_y electrode can continuously work for 300 h at 100 mA cm^-2 . When applying the CeFeO_x H_y nanosheet electrode as the anode and coupling it with the platinum mesh cathode, the cell voltage for overall water splitting can be lowered to 1.47 V at 10 mA cm^-2 . This work offers a design strategy for highly active, low-cost, and durable material through interfacing high valent metals with earth-abundant oxides/hydroxides.

Lithium-Directed Transformation of Amorphous Iridium (Oxy)hydroxides To Produce Active Water Oxidation Catalysts

The oxygen evolution reaction (OER) is crucial to future energy systems based on water electrolysis. Iridium oxides are promising catalysts due to their resistance to corrosion under acidic and oxidizing conditions. Highly active iridium (oxy)hydroxides prepared using alkali metal bases transform into low activity rutile IrO₂ at elevated temperatures (>350 °C) during catalyst/electrode preparation. Depending on the residual amount of alkali metals, we now show that this transformation can result in either rutile IrO₂ or nano-crystalline Li-intercalated IrO_x. While the transition to rutile results in poor activity, the Li-intercalated IrO_x has comparative activity and improved stability when compared to the highly active amorphous material despite being treated at 500 °C. This highly active nanocrystalline form of lithium iridate could be more resistant to industrial procedures to produce PEM membranes and provide a route to stabilize the high populations of redox active sites of amorphous iridium (oxy)hydroxides.

Electrocatalysis Mechanism and Structure-Activity Relationship of Atomically Dispersed Metal-Nitrogen-Carbon Catalysts for Electrocatalytic Reactions

Atomically dispersed metal-nitrogen-carbon catalysts (M-N-C) have been widely used in the field of energy conversion, which has already attracted a huge amount of attention. Due to their unsaturated d-band electronic structure of the center atoms, M-N-C catalysts can be applied in different electrocatalytic reactions by adjusting their own microscopic electronic structures to achieve the optimization of the structure-activity relationship. Consequently, it is of great significance for the revelation of electrocatalytic mechanism and structure-activity relationship of M-N-C catalysts. Thus, this review first introduces the relative research methods, including in situ/operando characterization techniques and theoretical calculation methods. Furthermore, clarifying the electrocatalytic mechanism and structure-activity relationship of M-N-C catalysts in different electrochemical energy conversion reactions is focused. Moreover, the future research directions are pointed out based on the discussion. This review will provide good guidance to systematically study the catalytic mechanism of single-atom catalysts and reasonably design the single-atom catalysts.

Interface Engineering on Amorphous/Crystalline Hydroxides/Sulfides Heterostructure Nanoarrays for Enhanced Solar Water Splitting

Developing highly efficient and stable noble-metal-free electrocatalysts for water splitting is critical for producing clean and sustainable energy. Here, we design a hierarchical transition metal hydroxide/sulfide (NiFe(OH)_x-Ni₃S₂/NF) electrode with dual heterointerface coexistence using a cation exchange-induced surface reconfiguration strategy. The electrode exhibits superior electrocatalytic activities, achieving low overpotentials of 55 mV for hydrogen evolution and 182 mV for oxygen evolution at 10 mA cm^-2. Furthermore, the assembled two-electrode system requires voltages as low as 1.55 and 1.62 V to deliver industrially relevant current densities of 500 and 1000 mA cm^-2, respectively, with excellent durability for over 200 h, which is comparable to commercial electrolysis. Theoretical calculations reveal that the hierarchical heterostructure increases the electronic delocalization of the Fe and Ni catalytic centers, lowering the energy barrier of the rate-limiting step and promoting O₂ desorption. Finally, by implementing the catalysts in a solar-driven water electrolysis system, we demonstrate a record and durable solar-to-hydrogen (STH) conversion efficiency of up to 20.05%. This work provides a promising strategy for developing low-cost and high-efficiency bifunctional catalysts for a large-scale solar-to-hydrogen generation.

Design of Single-Atom Catalysts and Tracking Their Fate Using Operando and Advanced X-ray Spectroscopic Tools

The potential of operando X-ray techniques for following the structure, fate, and active site of single-atom catalysts (SACs) is highlighted with emphasis on a synergetic approach of both topics. X-ray absorption spectroscopy (XAS) and related X-ray techniques have become fascinating tools to characterize solids and they can be applied to almost all the transition metals deriving information about the symmetry, oxidation state, local coordination, and many more structural and electronic properties. SACs, a newly coined concept, recently gained much attention in the field of heterogeneous catalysis. In this way, one can achieve a minimum use of the metal, theoretically highest efficiency, and the design of only one active site-so-called single site catalysts. While single sites are not easy to characterize especially under operating conditions, XAS as local probe together with complementary methods (infrared spectroscopy, electron microscopy) is ideal in this research area to prove the structure of these sites and the dynamic changes during reaction. In this review, starting from their fundamentals, various techniques related to conventional XAS and X-ray photon in/out techniques applied to single sites are discussed with detailed mechanistic and in situ/operando studies. We systematically summarize the design strategies of SACs and outline their exploration with XAS supported by density functional theory (DFT) calculations and recent machine learning tools.

Emerging Applications of Synchrotron Radiation X-Ray Techniques in Single Atomic Catalysts

Single atom catalysts (SACs) can achieve a maximum atom utilization efficiency of 100%, which provides significantly increased active sites compared with traditional catalysts during catalytic reactions. Synchrotron radiation technology is an important characterization method for identifying single-atom catalysts. Several types of internal information, such as the coordination number, bond length and electronic structure of metals, can all be analyzed. This review will focus on the introduction of synchrotron radiation techniques and their applications in SACs. First, the fundamentals of synchrotron radiation and the corresponding techniques applied in characterization of SACs will be briefly introduced, such as X-ray absorption near edge spectroscopy and extended X-ray absorption fine structure spectroscopy and in situ techniques. The detailed information obtained from synchrotron radiation X-ray characterization is described through four routes: 1) the local environment of a specific atom; 2) the oxidation state of SACs; 3) electronic structures at different orbitals; and 4) the in situ structure modification during catalytic reaction. In addition, a systematic summary of synchrotron radiation X-ray characterization on different types of SACs (noble metals and transition metals) will be discussed.

Efficient H2 Evolution Coupled with Anodic Oxidation of Iodide over Defective Carbon-Supported Single-Atom Mo-N4 Electrocatalyst

We successfully prepared nitrogen-doped defective carbon spheres (Mo-N₄/d-C) with a high loading of 0.996 wt % via a designed vapor-deposition process for IOR-based hydrogen generation. The synthesized Mo-N₄/d-C catalyst provides a record current density of 10 mA cm^-2 at 0.77 V. Further, the Mo-N₄/d-C catalyst shows a Tafel slope of 25.58 mV dec^-1, exceptional stability over time in acidic media, a higher hydrogen generation rate of 0.1063 mL g_cat^-1 min^-1, a high Faradaic efficiency of 99.8%, and a reduction of the energy consumption up to ∼50% for hydrogen evolution by anodic oxidation reaction of iodide (IOR) compared with the conventional OER-based electrolysis. Computational calculations demonstrate that the Mo-N₄/d-C structure plays a vital effect on the activity of iodide oxidation, which is competitive with the Pt catalyst.

Catalysis for e-Chemistry: Need and Gaps for a Future De-Fossilized Chemical Production, with Focus on the Role of Complex (Direct) Syntheses by Electrocatalysis

The prospects, needs and limits in current approaches in catalysis to accelerate the transition to e-chemistry, where this term indicates a fossil fuel-free chemical production, are discussed. It is suggested that e-chemistry is a necessary element of the transformation to meet the targets of net zero emissions by year 2050 and that this conversion from the current petrochemistry is feasible. However, the acceleration of the development of catalytic technologies based on the use of renewable energy sources (indicated as reactive catalysis) is necessary, evidencing that these are part of a system of changes and thus should be assessed from this perspective. However, it is perceived that the current studies in the area are not properly addressing the needs to develop the catalytic technologies required for e-chemistry, presenting a series of relevant aspects and directions in which research should be focused to develop the framework system transformation necessary to implement e-chemistry.

Unveiling the Genesis and Effectiveness of Negative Fading in Nanostructured Iron Oxide Anode Materials for Lithium-Ion Batteries

Iron oxide anode materials for rechargeable lithium-ion batteries have garnered extensive attention because of their inexpensiveness, safety, and high theoretical capacity. Nanostructured iron oxide anodes often undergo negative fading, that is, unconventional capacity increase, which results in a capacity increasing upon cycling. However, the detailed mechanism of negative fading still remains unclear, and there is no consensus on the provenance. Herein, we comprehensively investigate the negative fading of iron oxide anodes with a highly ordered mesoporous structure by utilizing advanced synchrotron-based analysis. Electrochemical and structural analyses identified that the negative fading originates from an optimization of the electrolyte-derived surface layer, and the thus formed layer significantly contributes to the structural stability of the nanostructured electrode materials, as well as their cycle stability. This work provides an insight into understanding the origin of negative fading and its influence on nanostructured anode materials.

Multistep protection strategy for preparation of atomically dispersed Fe–N catalysts for selective oxidation of ethylbenzene to acetophenone

Atomically dispersed Fe atoms on three-dimensional N-doped hollow carbon spheres single-atom catalyst was prepared, which exhibit excellent catalytic performance for the catalytic oxidation of ethylbenzene under mild reaction conditions.

Fe-N-C electrocatalysts in the oxygen and nitrogen cycles in alkaline media: the role of iron carbide

Fe-N-C electrocatalysts hold a great promise for Pt-free energy conversion, driving the electrocatalysis of oxygen reduction and evolution, oxidation of nitrogen fuels, and reduction of N₂, CO₂, and NO_x. Nevertheless, the catalytic role of iron carbide, a component of nearly every pyrolytic Fe-N-C material, is at the focus of a heated controversy. We now resolve the debate by examining a broad range of Fe₃C sites, spanning across many typical size distributions and carbon environments. Removing Fe₃C selectively by a non-oxidizing acid reveals its inactivity towards two representative reactions in alkaline media, oxygen reduction and hydrazine oxidation. The activity is assigned to other pre-existing sites, most probably Fe-N_x. DFT calculations prove that the Fe₃C surface binds O and N intermediates too strongly to be catalytic. By settling the argument on the catalytic role of Fe₃C in alkaline electrocatalysis, we hope to spur innovation in this critical field.

Nanocarbon for Energy Material Applications: N2 Reduction Reaction

Nanocarbons are an important class of energy materials and one relevant application is for the nitrogen reduction reaction, i.e., the direct synthesis of NH₃ from N₂ and H₂ O via photo- and electrocatalytic approaches. Ammonia is also a valuable energy or hydrogen vector. This perspective paper analyses developments in the field, limiting discussion to nanocarbon-based electrodes. These aspects are discussed: i) active sites related to charge density differences on C atoms associated to defects/strains, ii) doping with heteroatoms, iii) introduction of isolated metal ions, iv) creation and in situ dynamics of metal oxide(hydroxide)/nanocarbon boundaries, and v) nanocarbon characteristics to control the interface. Discussion is focused on the performances and mechanistic aspects. Aim is not a systematic state-of-the-art report but to highlight the need to use a different perspective in studying this challenging reaction by using selected papers. Notwithstanding the large differences in the proposed nature of the active sites, fall all within a restricted range of performances, far from the targets. A holistic approach is emphasized to make a breakthrough advance.

Unexpected high selectivity for acetate formation from CO2 reduction with copper based 2D hybrid catalysts at ultralow potentials

Copper-based catalysts are efficient for CO₂ reduction affording commodity chemicals. However, Cu(i) active species are easily reduced to Cu(0) during the CO₂RR, leading to a rapid decay of catalytic performance. Herein, we report a hybrid-catalyst that firmly anchors 2D-Cu metallic dots on F-doped Cu_xO nanoplates (Cu_xOF), synthesized by electrochemical-transformation under the same conditions as the targeted CO₂RR. The as-prepared Cu/Cu_xOF hybrid showed unusual catalytic activity towards the CO₂RR for CH₃COO⁻ generation, with a high FE of 27% at extremely low potentials. The combined experimental and theoretical results show that nanoscale hybridization engenders an effective s,p-d coupling in Cu/Cu_xOF, raising the d-band center of Cu and thus enhancing electroactivity and selectivity for the acetate formation. This work highlights the use of electronic interactions to bias a hybrid catalyst towards a particular pathway, which is critical for tuning the activity and selectivity of copper-based catalysts for the CO₂RR.

A two-dimensional (2D) copper hybrid catalyst (Cu/Cu_xOF) composed of metallic Cu well dispersed on 2D F-doped Cu_xO nanoplates (Cu_xOF) is reported, which shows high catalytic activity toward the CO₂RR for acetate generation.

Boosting the Electrocatalytic Conversion of Nitrogen to Ammonia on Metal-Phthalocyanine-Based Two-Dimensional Conjugated Covalent Organic Frameworks

The electrochemical N₂ reduction reaction (NRR) under ambient conditions is attractive in replacing the current Haber-Bosch process toward sustainable ammonia production. Metal-heteroatom-doped carbon-rich materials have emerged as the most promising NRR electrocatalysts. However, simultaneously boosting their NRR activity and selectivity remains a grand challenge, while the principle for precisely tailoring the active sites has been elusive. Herein, we report the first case of crystalline two-dimensional conjugated covalent organic frameworks (2D c-COFs) incorporated with M-N₄-C centers as novel, defined, and effective catalysts, achieving simultaneously enhanced activity and selectivity of electrocatalytic NRR to ammonia. Such 2D c-COFs are synthesized based on metal-phthalocyanine (M = Fe, Co, Ni, Mn, Zn, and Cu) and pyrene units bonded by pyrazine linkages. Significantly, the 2D c-COFs with Fe-N₄-C center exhibit higher ammonia yield rate (33.6 μg h^-1 mg_cat^-1) and Faradaic efficiency (FE, 31.9%) at -0.1 V vs reversible hydrogen electrode than those with other M-N₄-C centers, making them among the best NRR electrocatalysts (yield rate >30 μg h^-1 mg_cat^-1 and FE > 30%). In situ X-ray absorption spectroscopy, Raman spectroelectrochemistry, and theoretical calculations unveil that Fe-N₄-C centers act as catalytic sites. They show a unique electronic structure with localized electronic states at Fermi level, allowing for stronger interaction with N₂ and thus faster N₂ activation and NRR kinetics than other M-N₄-C centers. Our work opens the possibility of developing metal-nitrogen-doped carbon-rich 2D c-COFs as superior NRR electrocatalyst and provides an atomic understanding of the NRR process on M-N_x-C based electrocatalysts for designing high-performance NRR catalysts.

Recent Advances in Interface Engineering for Electrocatalytic CO2 Reduction Reaction

Electrocatalytic CO₂ reduction reaction (CO₂RR) can store and transform the intermittent renewable energy in the form of chemical energy for industrial production of chemicals and fuels, which can dramatically reduce CO₂ emission and contribute to carbon-neutral cycle. Efficient electrocatalytic reduction of chemically inert CO₂ is challenging from thermodynamic and kinetic points of view. Therefore, low-cost, highly efficient, and readily available electrocatalysts have been the focus for promoting the conversion of CO₂. Very recently, interface engineering has been considered as a highly effective strategy to modulate the electrocatalytic performance through electronic and/or structural modulation, regulations of electron/proton/mass/intermediates, and the control of local reactant concentration, thereby achieving desirable reaction pathway, inhibiting competing hydrogen generation, breaking binding-energy scaling relations of intermediates, and promoting CO₂ mass transfer. In this review, we aim to provide a comprehensive overview of current developments in interface engineering for CO₂RR from both a theoretical and experimental standpoint, involving interfaces between metal and metal, metal and metal oxide, metal and nonmetal, metal oxide and metal oxide, organic molecules and inorganic materials, electrode and electrolyte, molecular catalysts and electrode, etc. Finally, the opportunities and challenges of interface engineering for CO₂RR are proposed.

The Significance of Properly Reporting Turnover Frequency in Electrocatalysis Research

For decades, turnover frequency (TOF) has served as an accurate descriptor of the intrinsic activity of a catalyst, including those in electrocatalytic reactions involving both fuel generation and fuel consumption. Unfortunately, in most of the recent reports in this area, TOF is often not properly reported or not reported at all, in contrast to the overpotentials at a benchmarking current density. The current density is significant in determining the apparent activity, but it is affected by catalyst-centric parasitic reactions, electrolyte-centric competing reactions, and capacitance. Luckily, a properly calculated TOF can precisely give the intrinsic activity free from these phenomena in electrocatalysis. In this Viewpoint we ask: 1) What makes the commonly used activity markers unsuitable for intrinsic activity determination? 2) How can TOF reflect the intrinsic activity? 3) Why is TOF still underused in electrocatalysis? 4) What methods are used in TOF determination? and 5) What is essential in the more accurate calculation of TOF? Finally, the significance of normalizing TOF by Faradaic efficiency (FE) is stressed and we give our views on the development of universal analytical tools to determine the exact number of active sites and real surface area for all kinds of materials.

Catalyst Design for Electrochemical Reduction of CO2 to Multicarbon Products

Electrochemical reduction of CO₂ (CO₂ RR), driven by renewable energy (such as wind and solar energy), is an effective route toward carbon neutralization. The multicarbon (C₂₊ ) products from CO₂ RR are highly desirable, since they are important fuels, chemicals, and industrial raw materials. However, selective reduction of CO₂ to C₂₊ products is especially challenging, due to low selectivity, poor yield, and high overpotential. Since the performance of CO₂ RR is closely related to the structure and composition of catalysts, which alter the binding energy of intermediates generated in CO₂ RR, it is necessary to study these effects systematically to achieve possible design strategies. Herein, design strategies toward catalysts for CO₂ conversion to C₂₊ products are discussed on the basis of the adjustment of the structure and composition of catalysts, such as morphology control, defect engineering, bimetal, and surface modification. Meanwhile the reaction mechanisms and structure evolution of catalysts during CO₂ RR are focused on in particular. Finally, challenges and perspectives are proposed for further improvement of CO₂ RR technologies.

Single-Atom Electrocatalysts for Multi-Electron Reduction of CO2

The multi-electron reduction of CO₂ to hydrocarbons or alcohols is highly attractive in a sustainable energy economy, and the rational design of electrocatalysts is vital to achieve these reactions efficiently. Single-atom electrocatalysts are promising candidates due to their well-defined coordination configurations and unique electronic structures, which are critical for delivering high activity and selectivity and may accelerate the explorations of the activity origin at atomic level as well. Although much effort has been devoted to multi-electron reduction of CO₂ on single-atom electrocatalysts, there are still no reviews focusing on this emerging field and constructive perspectives are also urgent to be addressed. Herein recent advances in how to design efficient single-atom electrocatalysts for multi-electron reduction of CO₂ , with emphasis on strategies in regulating the interactions between active sites and key reaction intermediates, are summarized. Such interactions are crucial in designing active sites for optimizing the multi-electron reduction steps and maximizing the catalytic performance. Different design strategies including regulation of metal centers, single-atom alloys, non-metal single-atom catalysts, and tandem catalysts, are discussed accordingly. Finally, current challenges and future opportunities for deep electroreduction of CO₂ are proposed.

Engineering single-atomic ruthenium catalytic sites on defective nickel-iron layered double hydroxide for overall water splitting

Rational design of single atom catalyst is critical for efficient sustainable energy conversion. However, the atomic-level control of active sites is essential for electrocatalytic materials in alkaline electrolyte. Moreover, well-defined surface structures lead to in-depth understanding of catalytic mechanisms. Herein, we report a single-atomic-site ruthenium stabilized on defective nickel-iron layered double hydroxide nanosheets (Ru₁/D-NiFe LDH). Under precise regulation of local coordination environments of catalytically active sites and the existence of the defects, Ru₁/D-NiFe LDH delivers an ultralow overpotential of 18 mV at 10 mA cm⁻² for hydrogen evolution reaction, surpassing the commercial Pt/C catalyst. Density functional theory calculations reveal that Ru₁/D-NiFe LDH optimizes the adsorption energies of intermediates for hydrogen evolution reaction and promotes the O–O coupling at a Ru–O active site for oxygen evolution reaction. The Ru₁/D-NiFe LDH as an ideal model reveals superior water splitting performance with potential for the development of promising water-alkali electrocatalysts.

Rational design of single atom catalyst is critical for efficient sustainable energy conversion. Single-atomic-site ruthenium stabilized on defective nickel-iron layered double hydroxide nanosheets achieve superior HER and OER performance in alkaline media.

Recent advances in single atom catalysts for the electrochemical carbon dioxide reduction reaction

The electrochemical carbon dioxide reduction reaction (CO2RR) offers a promising solution to mitigate carbon emission and at the same time generate valuable carbonaceous chemicals/fuels. Single atom catalysts (SACs) are encouraging to catalyze the electrochemical CO2RR due to the tunable electronic structure of the central metal atoms, which can regulate the adsorption energy of reactants and reaction intermediates. Moreover, SACs form a bridge between homogeneous and heterogeneous catalysts, providing an ideal platform to explore the reaction mechanism of electrochemical reactions. In this review, we first discuss the strategies for promoting the CO2RR performance, including suppression of the hydrogen evolution reaction (HER), generation of C1 products and formation of C2+ products. Then, we summarize the recent developments in regulating the structure of SACs toward the CO2RR based on the above aspects. Finally, several issues regarding the development of SACs for the CO2RR are raised and possible solutions are provided.