Quantifying the factors limiting rate performance in battery electrodes

Transition metal Si-chalcogenides: a new two-dimensional anode material for Na-ion batteries

Sodium (Na) ion batteries (SIB) hold great importance in energy storage due to their potential to offer a sustainable and cost-effective alternative to traditional lithium-ion batteries. Na is abundantly available and less expensive than lithium, making it an attractive option for large-scale energy storage applications. In the present work, we have predicted a series of 2D transition metal (TM) Si-chalcogenides (TMSiCs), TM2X2Si (TM = Ta, Nb and X = S, Se), which exhibit metallic characteristics. All these materials are dynamically stable, but only Ta2S2Si, Ta2Se2Si and Nb2Se2Si are thermally stable even at an elevated temperature of 400 K. Through first-principles calculations, we show that Ta2S2Si, Ta2Se2Si and Nb2Se2Si are promising anode materials for SIB. These materials have a low Na migration barrier in the range of 0.13 to 0.17 eV, which could enhance the cycling performance of the SIB. The calculated average open circuit voltage (OCV) is small, i.e. 0.48, 0.4 and 0.47 V for Ta2S2Si, Ta2Se2Si and Nb2Se2Si, respectively, which suggests the possibility of higher output voltage and larger energy density of the battery. The maximum Na ion capacities for Ta2S2Si, Ta2Se2Si and Nb2Se2Si are calculated to be 206.6, 171.3 and 252.4 mA h g-1, respectively. Our results could provide fundamental insights into TM2X2Si for energy storage applications.

Stress-Relieving Carboxylated Polythiophene/Single-Walled Carbon Nanotube Conductive Layer for Stable Silicon Microparticle Anodes in Lithium-Ion Batteries

Stress-relieving and electrically conductive single-walled carbon nanotubes (SWNTs) and conjugated polymer, poly[3-(potassium-4-butanoate)thiophene] (PPBT), wrapped silicon microparticles (Si MPs) have been developed as a composite active material to overcome technical challenges such as intrinsically low electrical conductivity, low initial Coulombic efficiency, and stress-induced fracture due to severe volume changes of Si-based anodes for lithium-ion batteries (LIBs). The PPBT/SWNT protective layer surrounding the surface of the microparticles physically limits volume changes and inhibits continuous solid electrolyte interphase (SEI) layer formation that leads to severe pulverization and capacity loss during cycling, thereby maintaining electrode integrity. PPBT/SWNT-coated Si MP anodes exhibited high initial Coulombic efficiency (85%) and stable capacity retention (0.027% decay per cycle) with a reversible capacity of 1894 mA h g-1 after 300 cycles at a current density of 2 A g-1, 3.3 times higher than pristine Si MP anodes. The stress relaxation and underlying mechanism associated with the incorporation of the PPBT/SWNT layer were interpreted by quasi-deterministic and quantitative stress analyses of SWNTs through in situ Raman spectroscopy. PPBT/SWNT@Si MP anodes can maintain reversible stress recovery and 45% less variation in tensile stress compared with SWNT@Si MP anodes during cycling. The results verify the benefits of stress relaxation via a protective capping layer and present an efficient strategy to achieve long cycle life for Si-based anodes for next-generation LIBs.

Diffusion and structure of propylene carbonate-metal salt electrolyte solutions for post-lithium-ion batteries: From experiment to simulation

The diffusion of cations in organic solvent solutions is important for the performance of metal-ion batteries. In this article, pulsed field gradient nuclear magnetic resonance experiments and fully atomistic molecular dynamic simulations were employed to study the temperature-dependent diffusive behavior of various liquid electrolytes representing 1M propylene carbonate solutions of metal salts with bis(trifluoromethylsulfonyl)imide (TFSI-) or hexafluorophosphate (PF6-) anions commonly used in lithium-ion batteries and beyond. The experimental studies revealed the temperature dependence of the diffusion coefficients for the propylene carbonate (PC) solvent and for the anions following an Arrhenius type of behavior. It was observed that the PC molecules are the faster species. For the monovalent cations (Li+, Na+, K+), the PC solvent diffusion was enhanced as the cation size increased, while for the divalent cations (Mg2+, Ca2+, Sr2+, Ba2+), the opposite trend was observed, i.e., the diffusion coefficients decreased as the cation size increased. The anion diffusion in LiTFSI and NaTFSI solutions was found to be similar, while in electrolytes with divalent cations, a decrease in anion diffusion with increasing cation size was observed. It was shown that non-polarizable charge-scaled force fields could correspond perfectly to the experimental values of the anion and PC solvent diffusion coefficients in salt solutions of both monovalent (Li+, Na+, K+) and divalent (Mg2+, Ca2+, Sr2+, Ba2+) cations at a range of operational temperatures. Finally, after calculating the radial distribution functions between cations, anions, and solvent molecules, the increase in the PC diffusion coefficient established with the increase in cation size for monovalent cations was clearly explained by the large hydration shell of small Li+ cations, due to their strong interaction with the PC solvent. In solutions with larger monovalent cations, such as Na+, and with a smaller solvation shell of PC, the PC diffusion is faster due to more liberated solvent molecules. In the salt solutions with divalent cations, both the anion and the PC diffusion coefficients decreased as the cation size increased due to an enhanced cation-anion coordination, which was accompanied by an increase in the amount of PC in the cation solvation shell due to the presence of anions.

Simple Framework for Simultaneous Analysis of Both Electrodes in Stoichiometric Lithium-Sulfur Batteries

A battery is composed of two electrodes that depend on and interact with each other. However, galvanostatic charging-discharging measurement, the most widely used method for battery evaluation, cannot simultaneously reflect performance metrics [capacity, Coulombic efficiency (CE), and cycling stability] of both electrodes because the result is generally governed by the lower-capacity electrode of the cell, namely the limiting reagent of the battery reaction. In studying stoichiometric Li-S cells operating under application-relevant high-mass-loading and lean-electrolyte conditions, we take advantage of the two-stage discharging behavior of sulfur to construct a simple framework that allows us to analyze both electrodes simultaneously. The cell capacity and its decay are anode performance descriptors, whereas the first plateau capacity and cell CE are cathode performance descriptors. Our analysis within this frame identifies Li stripping/plating and polysulfide shuttling to be the limiting factors for the cycling performance of the stoichiometric Li-S cell. Using our newly developed framework, we examine various previously reported strategies to mitigate these bottleneck problems and find modifying the separator with a reduced graphene oxide layer to be an effective means, which improves the capacity retention rate of the cell to 99.7% per cycle.

Construction of Hierarchical Conductive Networks for LiNi0.8Mn0.1Co0.1O2 Cathode toward Stable Cycling at High Areal Mass Loadings

Realizing high-performance thick electrodes is considered as a practical strategy to promote the energy density of lithium-ion batteries. However, establishing effective transport pathways for both lithium-ions and electrons in a thick electrode is very challenging. This study develops a hierarchical conductive network structure for constructing high-performance NMC811 (LiNi0.8Mn0.1Co0.1O2) cathode toward stable cycling at high areal mass loadings. The hierarchical conductive networks are composed of a Li+/e- mixed conducting interface (lithium polyacrylate/hydroxyl-functionalized multiwalled carbon nanotubes) on NMC811 particles, and a segregated network of single-walled carbon nanotubes in the electrode, without any additional binders or carbon black. Such strategy endows the NMC811 cathode (up to 250 µm and 50 mg cm-2) with low porosity/tortuosity, ultrahigh Li+/e- conductivities and excellent mechanical property at low carbon nanotube content (1.8 wt%). It significantly improves the electrochemical reaction homogeneity along the electrode depth, meanwhile effectively inhibits the side reactions at the electrode/electrolyte interface and cracks in the NMC particles during cycling. This work emphasizes the crucial role of the electronic/ionic cooperative transportation in the performance deterioration of thick cathodes, and provide guidance for architecture optimization and performance improvement of thick electrodes toward practical applications, not just for the NMC811 cathode.

Liquid-Phase Exfoliation of Arsenic Trisulfide (As2S3) Nanosheets and Their Use as Anodes in Potassium-Ion Batteries

Here, we demonstrate the production of 2D nanosheets of arsenic disulfide (As2S3) via liquid-phase exfoliation of the naturally occurring mineral, orpiment. The resultant nanosheets had mean lateral dimensions and thicknesses of 400 and 10 nm, and had structures indistinguishable from the bulk. The nanosheets were solution mixed with carbon nanotubes and cast into nanocomposite films for use as anodes in potassium-ion batteries. These anodes exhibited outstanding electrochemical performance, demonstrating an impressive discharge capacity of 619 mAh/g at a current density of 50 mA/g. Even after 1000 cycles at 500 mA/g, the anodes retained an impressive 94% of their capacity. Quantitative analysis of the rate performance yielded a capacity at a very low rate of 838 mAh/g, about two-thirds of the theoretical capacity of As2S3 (1305 mAh/g). However, this analysis also implied As2S3 to have a very small solid-state diffusion coefficient (∼10-17 m2/s), somewhat limiting its potential for high-rate applications.

Additive-Free Anode with High Stability: Nb2CTx MXene Prepared by HCl-LiF Hydrothermal Etching for Lithium-Ion Batteries

MXenes, represented by Ti3C2Tx, have been widely studied in the electrochemical energy storage fields, including lithium-ion batteries, for their unique two-dimensional structure, tunable surface chemistry, and excellent electrical conductivity. Recently, Nb2CTx, as a new type of MXene, has attracted more and more attention due to its high theoretical specific capacity of 542 mAh g-1. However, the preparation of few-layer Nb2CTx nanosheets with high-quality remains a challenge, which limits their research and application. In this work, high-quality few-layer Nb2CTx nanosheets with a large lateral size and a high conductivity of up to 500 S cm-1 were prepared by a simple HCl-LiF hydrothermal etching method, which is 2 orders of magnitude higher than that of previously reported Nb2CTx. Furthermore, from its aqueous ink, the viscosity-tunable organic few-layer Nb2CTx ink was prepared by HCl-induced flocculation and N-methyl-2-pyrrolidone treatment. When using the organic few-layer Nb2CTx ink as an additive-free anode of lithium-ion batteries, it showed excellent cycling performance with a reversible specific capacity of 524.0 mAh g-1 after 500 cycles at 0.5 A g-1 and 444.0 mAh g-1 after 5000 cycles at 1 A g-1. For rate performance, a specific capacity of 159.8 mAh g-1 was obtained at a high current density of 5 A g-1, and an excellent capacity retention rate of about 95.65% was achieved when the current density returned to 0.5 A g-1. This work presents a simple and scalable process for the preparation of high-quality Nb2CTx and its aqueous/organic ink, which demonstrates important application potential as electrodes for electrochemical energy storage devices.

Halogen-powered static conversion chemistry

Halogen-powered static conversion batteries (HSCBs) thrive in energy storage applications. They fall into the category of secondary non-flow batteries and operate by reversibly changing the chemical valence of halogens in the electrodes or/and electrolytes to transfer electrons, distinguishing them from the classic rocking-chair batteries. The active halide chemicals developed for these purposes include organic halides, halide salts, halogenated inorganics, organic-inorganic halides and the most widely studied elemental halogens. Aside from this, various redox mechanisms have been discovered based on multi-electron transfer and effective reaction pathways, contributing to improved electrochemical performances and stabilities of HSCBs. In this Review, we discuss the status of HSCBs and their electrochemical mechanism-performance correlations. We first provide a detailed exposition of the fundamental redox mechanisms, thermodynamics, conversion and catalysis chemistry, and mass or electron transfer modes involved in HSCBs. We conclude with a perspective on the challenges faced by the community and opportunities towards practical applications of high-energy halogen cathodes in energy-storage devices.

New Emerging Fast Charging Microscale Electrode Materials

Fast charging lithium (Li)-ion batteries are intensively pursued for next-generation energy storage devices, whose electrochemical performance is largely determined by their constituent electrode materials. While nanosizing of electrode materials enhances high-rate capability in academic research, it presents practical limitations like volumetric packing density and high synthetic cost. As an alternative to nanosizing, microscale electrode materials cannot only effectively overcome the limitations of the nanosizing strategy but also satisfy the requirement of fast-charging batteries. Therefore, this review summarizes the new emerging microscale electrode materials for fast charging from the commercialization perspective. First, the fundamental theory of electronic/ionic motion in both individual active particles and the whole electrode is proposed. Then, based on these theories, the corresponding optimization strategies are summarized toward fast-charging microscale electrode materials. In addition, advanced functional design to tackle the mechanical degradation problems related to next generation high capacity alloy- and conversion-type electrode materials (Li, S, Si et al.) for achieving fast charging and stable cycling batteries. Finally, general conclusions and the future perspective on the potential research directions of microscale electrode materials are proposed. It is anticipated that this review will provide the basic guidelines for both fundamental research and practical applications of fast-charging batteries.

Recent Progress in Improving Rate Performance of Cellulose-Derived Carbon Materials for Sodium-Ion Batteries

Cellulose-derived carbon is regarded as one of the most promising candidates for high-performance anode materials in sodium-ion batteries; however, its poor rate performance at higher current density remains a challenge to achieve high power density sodium-ion batteries. The present review comprehensively elucidates the structural characteristics of cellulose-based materials and cellulose-derived carbon materials, explores the limitations in enhancing rate performance arising from ion diffusion and electronic transfer at the level of cellulose-derived carbon materials, and proposes corresponding strategies to improve rate performance targeted at various precursors of cellulose-based materials. This review also presents an update on recent progress in cellulose-based materials and cellulose-derived carbon materials, with particular focuses on their molecular, crystalline, and aggregation structures. Furthermore, the relationship between storage sodium and rate performance the carbon materials is elucidated through theoretical calculations and characterization analyses. Finally, future perspectives regarding challenges and opportunities in the research field of cellulose-derived carbon anodes are briefly highlighted.

Quantitative analysis of printed nanostructured networks using high-resolution 3D FIB-SEM nanotomography

Networks of solution-processed nanomaterials are becoming increasingly important across applications in electronics, sensing and energy storage/generation. Although the physical properties of these devices are often completely dominated by network morphology, the network structure itself remains difficult to interrogate. Here, we utilise focused ion beam - scanning electron microscopy nanotomography (FIB-SEM-NT) to quantitatively characterise the morphology of printed nanostructured networks and their devices using nanometre-resolution 3D images. The influence of nanosheet/nanowire size on network structure in printed films of graphene, WS2 and silver nanosheets (AgNSs), as well as networks of silver nanowires (AgNWs), is investigated. We present a comprehensive toolkit to extract morphological characteristics including network porosity, tortuosity, specific surface area, pore dimensions and nanosheet orientation, which we link to network resistivity. By extending this technique to interrogate the structure and interfaces within printed vertical heterostacks, we demonstrate the potential of this technique for device characterisation and optimisation.

Using a cyclocarbon additive as a cyclone separator to achieve fast lithiation and delithiation without dendrite growth in lithium-ion batteries

Carbon materials are widely used for reversible lithium uptake in the anode of lithium-ion batteries. Nevertheless, the challenge of uncontrollable dendrite deposition during fast charge-discharge cycles remains a grand hurdle. Various strategies have been explored to prevent detrimental heterogeneous dendrite metal deposits, such as interface engineering and electrolyte modification, but they often compromise the reverse diffusion freedom of Li+ ions during discharging and are incompatible with the most mainstream use of graphite as an anode material. Here, we propose the incorporation of a novel carbon allotrope of cyclocarbon as a potential additive in the anode. In contrast to conventional carbon materials, density functional theory calculations reveal that cyclocarbon has a much higher affinity for Li atoms than Li+ ions, even surpassing the inherent cohesion of Li atoms, due to the charge transfer from the 2s orbital of Li atoms to the unique in-plane π orbital of cyclocarbon. Furthermore, ab initio molecular dynamics simulations show that Li+ ions can shuttle freely back and forth across cyclocarbon, whereas the lithiation process for Li atoms occurs rapidly within picoseconds. The delithiation of Li atoms within cyclocarbon follows a voltage-gated mechanism that is effectively controlled by an external electric field of 3 V nm-1. Remarkably, cyclocarbon exhibits potential compatibility with commercialized graphite electrodes via the π-π interaction and also can be extended to sodium-ion and potassium-ion batteries. These distinct compatibility, scalability and electrochemical properties of cyclocarbon provide a new avenue to realize both safety and ultrafast rechargeable performance of ion batteries.

Cobalt Oxide 2D Nanosheets Formed at a Polarized Liquid|Liquid Interface toward High-Performance Li-Ion and Na-Ion Battery Anodes

Cobalt oxide (Co3O4)-based nanostructures have the potential as low-cost materials for lithium-ion (Li-ion) and sodium-ion (Na-ion) battery anodes with a theoretical capacity of 890 mAh/g. Here, we demonstrate a novel method for the production of Co3O4 nanoplatelets. This involves the growth of flower-like cobalt oxyhydroxide (CoOOH) nanostructures at a polarized liquid|liquid interface, followed by conversion to flower-like Co3O4 via calcination. Finally, sonication is used to break up the flower-like Co3O4 nanostructures into two-dimensional (2D) nanoplatelets with lateral sizes of 20-100 nm. Nanoplatelets of Co3O4 can be easily mixed with carbon nanotubes to create nanocomposite anodes, which can be used for Li-ion and Na-ion battery anodes without any additional binder or conductive additive. The resultant electrodes display impressive low-rate capacities (at 125 mA/g) of 1108 and 1083 mAh/g, for Li-ion and Na-ion anodes, respectively, and stable cycling ability over >200 cycles. Detailed quantitative rate analysis clearly shows that Li-ion-storing anodes charge roughly five times faster than Na-ion-storing anodes.

Probing the Origin of Viscosity of Liquid Electrolytes for Lithium Batteries

Viscosity is an extremely important property for ion transport and wettability of electrolytes. Easy access to viscosity values and a deep understanding of this property remain challenging yet critical to evaluating the electrolyte performance and tailoring electrolyte recipes with targeted properties. We proposed a screened overlapping method to efficiently compute the viscosity of lithium battery electrolytes by molecular dynamics simulations. The origin of electrolyte viscosity was further comprehensively probed. The viscosity of solvents exhibits a positive correlation with the binding energy between molecules, indicating viscosity is directly correlated to intermolecular interactions. Salts in electrolytes enlarge the viscosity significantly with increasing concentrations while diluents serve as the viscosity reducer, which is attributed to the varied binding strength from cation-anion and cation-solvent associations. This work develops an accurate and efficient method for computing the electrolyte viscosity and affords deep insight into viscosity at the molecular level, which exhibits the huge potential to accelerate advanced electrolyte design for next-generation rechargeable batteries.

Correlating Rate-Dependent Transition Metal Dissolution between Structure Degradation in Li-Rich Layered Oxides

Understanding the mechanism of the rate-dependent electrochemical performance degradation in cathodes is crucial to developing fast charging/discharging cathodes for Li-ion batteries. Here, taking Li-rich layered oxide Li1.2 Ni0.13 Co0.13 Mn0.54 O2 as the model cathode, the mechanisms of performance degradation at low and high rates are comparatively investigated from two aspects, the transition metal (TM) dissolution and the structure change. Quantitative analyses combining spatial-resolved synchrotron X-ray fluorescence (XRF) imaging, synchrotron X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques reveal that low-rate cycling leads to gradient TM dissolution and severe bulk structure degradation within the individual secondary particles, and especially the latter causes lots of microcracks within secondary particles, and becomes the main reason for the fast capacity and voltage decay. In contrast, high-rate cycling leads to more TM dissolution than low-rate cycling, which concentrates at the particle surface and directly induces the more severe surface structure degradation to the electrochemically inactive rock-salt phase, eventually causing a faster capacity and voltage decay than low-rate cycling. These findings highlight the protection of the surface structure for developing fast charging/discharging cathodes for Li-ion batteries.

Single-Layer-Particle Electrode Design for Practical Fast-Charging Lithium-Ion Batteries

Efforts to enable fast charging and high energy density lithium-ion batteries (LIBs) are hampered by the trade-off nature of the traditional electrode design: increasing the areal capacity usually comes with sacrificing the fast charge transfer. Here a single-layer chunky particle electrode design is reported, where red-phosphorus active material is embedded in nanochannels of vertically aligned graphene (red-P/VAG) assemblies. Such an electrode design addresses the sluggish charge transfer stemming from the high tortuosity and inner particle/electrode resistance of traditional electrode architectures consisting of randomly stacked active particles. The vertical ion-transport nanochannels and electron-transfer conductive nanowalls of graphene confine the direction of charge transfer to minimize the transfer distance, and the incomplete filling of nanochannels in the red-P/VAG composite buffers volume change locally, thus avoiding the variation of electrodes thickness during cycling. The single-layer chunky particle electrode displays a high areal capacity (5.6 mAh cm^-2 ), which is the highest among the reported fast-charging battery chemistries. Paired with a high-loading LiNi_0.6 Co_0.2 Mn_0.2 O₂ (NCM622) cathode, a pouch cell shows stable cycling with high energy and power densities. Such a single-layer chunky particle electrode design can be extended to other advanced battery systems and boost the development of LIBs with fast-charging capability and high energy density.

Liquid Processing of Interfacially Grown Iron-Oxide Flowers into 2D-Platelets Yields Lithium-Ion Battery Anodes with Capacities of Twice the Theoretical Value

Iron oxide (Fe₂ O₃ ) is an abundant and potentially low-cost material for fabricating lithium-ion battery anodes. Here, the growth of α-Fe₂ O₃ nano-flowers at an electrified liquid-liquid interface is demonstrated. Sonication is used to convert these flowers into quasi-2D platelets with lateral sizes in the range of hundreds of nanometers and thicknesses in the range of tens of nanometers. These nanoplatelets can be combined with carbon nanotubes to form porous, conductive composites which can be used as electrodes in lithium-ion batteries. Using a standard activation process, these anodes display good cycling stability, reasonable rate performance and low-rate capacities approaching 1500 mAh g^-1 , consistent with the current state-of-the-art for Fe₂ O₃ . However, by using an extended activation process, it is found that the morphology of these composites can be significantly changed, rendering the iron oxide amorphous and significantly increasing the porosity and internal surface area. These morphological changes yield anodes with very good cycling stability and low-rate capacity exceeding 2000 mAh g^-1 , which is competitive with the best anode materials in the literature. However, the data implies that, after activation, the iron oxide displays a reduced solid-state lithium-ion diffusion coefficient resulting in somewhat degraded rate performance.

Tortuosity Engineering for Improved Charge Storage Kinetics in High-Areal-Capacity Battery Electrodes

The increasing demands of electronic devices and electric transportation necessitate lithium-ion batteries with simultaneous high energy and power capabilities. However, rate capabilities are often limited in high-loading electrodes due to the lengthy and tortuous ion transport paths with their electrochemical behaviors governed by complicated electrode architectures still elusive. Here, we report the electrode-level tortuosity engineering design enabling improved charge storage kinetics in high-energy electrodes. Both high areal capacity and high-rate capability can be achieved beyond the practical level of mass loadings in electrodes with vertically oriented architectures. The electrochemical properties in electrodes with various architectures were quantitatively investigated through correlating the characteristic time with tortuosity. The lithium-ion transport kinetics regulated by electrode architectures was further studied via combining the three-dimensional electrode architecture visualization and simulation. The tortuosity-controlled charge storage kinetics revealed in this study can be extended to general electrode systems and provide useful design consideration for next-generation high-energy/power batteries.

A Figure of Merit for Fast-Charging Li-ion Battery Materials

Rate capability is characterized necessarily in almost all battery-related reports, while there is no universal metric for quantitative comparison. Here, we proposed the characteristic time of diffusion, which mainly combines the effects of diffusion coefficients and geometric sizes, as an easy-to-use figure of merit (FOM) to standardize the comparison of fast-charging battery materials. It offers an indicator to rank the rate capabilities of different battery materials and suggests two general methods to improve the rate capability: decreasing the geometric sizes or increasing the diffusion coefficients. Based on this FOM, more comprehensive FOMs for quantifying the rate capabilities of battery materials are expected by incorporating other processes (interfacial reaction, migration) into the current diffusion-dominated electrochemical model. Combined with Peukert's empirical law, it may characterize rate capabilities of batteries in the future.

Opportunities and challenges for 2D heterostructures in battery applications: a computational perspective

With an increasing demand for large-scale energy storage systems, there is a need for novel electrode materials to store energy in batteries efficiently. 2D materials are promising as electrode materials for battery applications. Despite their excellent properties, none of the available single-phase 2D materials offers a combination of properties required for maximizing energy density, power density, and cycle life. This article discusses how stacking distinct 2D materials into a 2D heterostructure may open up new possibilities for battery electrodes, combining favourable characteristics and overcoming the drawbacks of constituent 2D layers. Computational studies are crucial to advancing this field rapidly with first-principles simulations of various 2D heterostructures forming the basis for such investigations that offer insights into processes that are hard to determine otherwise. We present a perspective on the current methodology, along with a review of the known 2D heterostructures as anodes and their potential for Li and Na-ion battery applications. 2D heterostructures showcase excellent tunability with different compositions. However, each of them has distinct properties, with its own set of challenges and opportunities for application in batteries. We highlight the current status and prospects to stimulate research into designing new 2D heterostructures for battery applications.

Constructing the Single-Phase Nanotubes with Uniform Dispersion of SiOx and Carbon as Stable Anodes for Lithium-Ion Batteries

SiOx is an attractive anode material for lithium-ion batteries due to its considerable capacity. However, its obvious volume expansion and low conductivity result in poor electrochemical performance. Herein, a novel single-phase nanotube structure with uniform distribution of nanoscale SiOx units and amorphous carbon matrix was fabricated. The hollow nanotube and homogeneously distributed ultrafine SiOx units greatly alleviate volume changes. The amorphous carbon facilitates electron transport throughout the network and offers a buffer to further reduce the volume expansion of SiOx. Benefiting from this unique structure, as-prepared single-phase SiOx/C NTs demonstrate excellent durability and rate capability. Specifically, it delivers a high reversible specific capacity (713 mAh g^-1 at 0.1 A g^-1 after 200 cycles); negligible capacity decay is confirmed after 500 cycles at high density current (544 mAh g^-1 at 1 A g^-1 after 500 cycles).

Gradient Architecture Design in Scalable Porous Battery Electrodes

Because it has been demonstrated to be effective toward faster ion diffusion inside the pore space, low-tortuosity porous architecture has become the focus in thick electrode designs, and other possibilities are rarely investigated. To advance current understanding in the structure-affected electrochemistry and to broaden horizons for thick electrode designs, we present a gradient electrode design, where porous channels are vertically aligned with smaller openings on one end and larger openings on the other. With its 3D morphology carefully visualized by Raman mapping, the electrochemical properties between opposite orientations of the gradient electrodes are compared, and faster energy storage kinetics is found in larger openings and more concentrated active material near the separator. As further verified by simulation, this study on gradient electrode design deepens the knowledge of structure-related electrochemistry and brings perspectives in high-energy battery electrode designs.

Process-Structure-Formulation Interactions for Enhanced Sodium Ion Battery Development: A Review

Before the viability of a cell formulation can be assessed for implementation in commercial sodium ion batteries, processes applied in cell production should be validated and optimized. This review summarizes the steps performed in constructing sodium ion (Na-ion) cells at research scale, highlighting parameters and techniques that are likely to impact measured cycling performance. Consistent process-structure-performance links have been established for typical lithium-ion (Li-ion) cells, which can guide hypotheses to test in Na-ion cells. Liquid electrolyte viscosity, sequence of mixing electrode slurries, rate of drying electrodes and cycling characteristics of formation were found critical to the reported capacity of laboratory cells. Based on the observed importance of processing to battery performance outcomes, the current focus on novel materials in Na-ion research should be balanced with deeper investigation into mechanistic changes of cell components during and after production, to better inform future designs of these promising batteries.

An Ultrahigh-Power Mesocarbon Microbeads|Na+ -Diglyme|Na3 V2 (PO4 )3 Sodium-Ion Battery

Sodium-ion batteries (SIBs) show practical applications in large-scale energy storage systems. But, their power density is limited by the sluggish Na⁺ diffusion into the cathode and anode materials. Herein, the authors demonstrate a prototype of ultrahigh power SIB, consisting of the high-rate Na₃ V₂ (PO₄ )₃ (NVP) cathode, graphite-type mesocarbon microbeads (MCMB) anode, and Na⁺ -diglyme electrolyte. It is found that the overpotential of the NVP cathode obeys the Ohmic rule. Thus, the as-synthesized NVP@C@carbon nanotubes (CNTs) cathode with the high conductive CNTs networks displays high electronic conductivity, reducing the overpotential and charge transfer resistances and leading to the remarkable rate capability over 1000C. For the MCMB anode, the initial [Na-diglyme]⁺ co-intercalation step is pseudocapacitive dominated, and then the expanded graphite's layers ensure the subsequent fast ions diffusion. The rapid (de)intercalation kinetics in between the cathode and anode are well-matched. Thus, the assembled MCMB|1 m NaPF₆ in diglyme|NVP@C@CNTs full-cell SIB delivers the energy density of 88 Wh kg^-1 at the high power density of ≈10 kW kg^-1 . Even at the ultrahigh power density of 23 kW kg^-1 , an energy density of 58 Wh kg^-1 is obtained. The encouraging results of the full cell will promote the development of high-power SIB for large-scale applications in the future.

A limitation map of performance for porous electrodes in lithium-ion batteries

Driven by expanding interest in battery storage solutions and the success story of lithium-ion batteries, the research for the discovery and optimization of new battery materials and concepts is at peak. The generation of experimental (dis)charge data using coin cells is fast and feasible and proves to be a favorite practice in the battery research labs. The quantitative interpretation of the data, however, is not trivial and decelerates the process of screening and optimization of electrode materials and recipes. Here, we introduce the concept of polarographic map and demonstrate how it can be leveraged to quantify the contribution of different non-equilibrium phenomena to the performance limitation and total polarization of a lithium-ion cell. We showcase the accuracy and diagnostic power of this approach by preparing and analyzing the electrochemical performance of 54 sets of LiNixMnyCo1-x-yO2 electrodes with different formulations and designs discharged in a range of 0.2C-5C.

Operando Analysis of Gas Evolution in TiNb2O7 (TNO)-Based Anodes for Advanced High-Energy Lithium-Ion Batteries under Fast Charging

TiNb₂O₇ (TNO) is regarded as one of the promising next-generation anode materials for lithium-ion batteries (LIBs) due to its high rate capabilities, higher theoretical capacity, and higher lithiation voltage. This enables the cycling of TNO-based anodes under extreme fast charging (XFC) conditions with a minimal risk of lithium plating compared to that of graphite anodes. Here, the gas evolution in real time with TNO-based pouch cells is first reported via operando mass spectrometry. The main gases are identified to be CO₂, C₂H₄, and O₂. A solid-electrolyte interphase is detected on TNO, which continues evolving, forming, and dissolving with the lithiation and delithiation of TNO. The gas evolution can be significantly reduced when a protective coating is applied on the TNO particles, reducing the CO₂ and C₂H₄ evolution by ∼2 and 5 times, respectively, at 0.1C in a half-cell configuration. The reduction on gas generation in full cells is even more pronounced. The surface coating also enables 20% improvement in capacity under XFC conditions.

A Quinone-Based Cathode Material for High-Performance Organic Lithium and Sodium Batteries

With the increased application of batteries in powering electric vehicles as well as potential contributions to utility-scale storage, there remains a need to identify and develop efficient and sustainable active materials for use in lithium (Li)- and sodium (Na)-ion batteries. Organic cathode materials provide a desirable alternative to inorganic counterparts, which often come with harmful environmental impact and supply chain uncertainties. Organic materials afford a sustainable route to active electrodes that also enable fine-tuning of electrochemical potentials through structural design. Here, we report a bis-anthraquinone-functionalized s-indacene-1,3,5,7(2H,6H)-tetraone (BAQIT) synthesized using a facile and inexpensive route as a high-capacity cathode material for use in Li- and Na-ion batteries. BAQIT provides multiple binding sites for Li- and Na-ions, while maintaining low solubility in commercial organic electrolytes. Electrochemical Li-ion cells demonstrate excellent stability with discharge capacities above 190 mAh g-1 after 300 cycles at a 0.1C rate. The material also displayed excellent high-rate performance with a reversible capacity of 142 mAh g-1 achieved at a 10C rate. This material affords high power capabilities superior to current state-of-the-art organic cathode materials, with values reaching 5.09 kW kg-1. The Na-ion performance was also evaluated, exhibiting reversible capacities of 130 mAh g-1 after 90 cycles at a 0.1C rate. This work offers a structural design to encourage versatile, high-power, and long cycle-life electrochemical energy-storage materials.

Mechanistic Insights into Fast Charging and Discharging of the Sodium Metal Battery Anode: A Comparison with Lithium

Na metal anode receives increasing attention as a low-cost alternative to Li metal anode for the application in high energy batteries. Despite extensive research efforts to improve the reversibility and cycle life of Na metal electrodes, their rate performance, i.e. electrochemical plating and stripping of Na metal at high current, is underexplored. Herein, we report that Na metal electrodes, unlike the more widely studied Li metal electrodes which survive high current density up to 20 mA/cm², cannot be fast charged or discharged in common ether electrolyte. The fast charging, namely metal plating, is comprised by severe side reactions that decompose electrolyte into electrochemically inactive Na(I) solid species. The fast discharging, namely metal stripping, is disabled by local Na removal that deteriorates the electrical contact with the current collector. While the fast charging failure is permanent, the capacity loss from fast discharging can be recovered through a restructuring process at a low discharging current which rebuilds the electrical connection. We further reveal that the unsatisfactory rate performance of Na metal electrodes is associated with intrinsic physicochemical properties of Na. This study delineates the mechanistic origins of Na's limitation in fast plating and stripping, and demonstrates the necessity of improving the charging and discharging rate performance of Na metal electrodes.

Lithium and Sodium Ion Binding Mechanisms and Diffusion Rates in Lignin-Based Hard Carbon Models

Hard carbons are the primary candidate for the anode of next-generation sodium-ion batteries for large-scale energy storage, as they are sustainable and can possess high charge capacity and long cycle life. These properties along with diffusion rates and ion storage mechanisms are highly dependent on nanostructures. This work uses reactive molecular dynamics simulations to examine lithium and sodium ion storage mechanisms and diffusion in lignin-based hard carbon model systems with varying nanostructures. It was found that sodium will preferentially localize on the surface of curved graphene fragments, while lithium will preferentially bind to the hydrogen dense interfaces of crystalline and amorphous carbon domains. The ion storage mechanisms are explained through ion charge and energy distributions in coordination with snapshots of the simulated systems. It was also revealed that hard carbons with small crystalline volume fractions and moderately sized sheets of curved graphene will yield the highest sodium-ion diffusion rates at ∼10-7 cm2/s. Self-diffusion coefficients were determined by mean square displacement of ions in the models with extension through a confined random walk theory.

Tunable Porous Electrode Architectures for Enhanced Li-Ion Storage Kinetics in Thick Electrodes

Thick electrodes, although promising toward high-energy battery systems, suffer from restricted lithium-ion transport kinetics due to prolonged diffusion lengths and tortuous transport pathways. Despite the emerging low-tortuosity designs, capacity retention under higher current densities is still limited. Herein, we employ a modified ice-templating method to fabricate low-tortuosity porous electrodes with tunable wall thickness and channel width and systematically investigate the critical impacts of the fine structural parameters on the thick electrode electrochemistry. While the porous electrodes with thick walls show diminished capability under a C-rate larger than 1.5 C, those with thinner walls could maintain ∼70% capacity under 2.5 C. The superior capacity retention is ascribed to the fast diffusion into the thin lamellar walls compared with their thicker counterparts. This study provides deeper insights into structure-affected electrochemistry and opens up new perspective of 3D porous architectural designs for high-energy and high-power electrodes.

Additive Manufacturing of Conducting Polymers: Recent Advances, Challenges, and Opportunities

Conducting polymers (CPs) have been attracting great attention in the development of (bio)electronic devices. Most of the current devices are rigid two-dimensional systems and possess uncontrollable geometries and architectures that lead to poor mechanical properties presenting ion/electronic diffusion limitations. The goal of the article is to provide an overview about the additive manufacturing (AM) of conducting polymers, which is of paramount importance for the design of future wearable three-dimensional (3D) (bio)electronic devices. Among different 3D printing AM techniques, inkjet, extrusion, electrohydrodynamic, and light-based printing have been mainly used. This review article collects examples of 3D printing of conducting polymers such as poly(3,4-ethylene-dioxythiophene), polypyrrole, and polyaniline. It also shows examples of AM of these polymers combined with other polymers and/or conducting fillers such as carbon nanotubes, graphene, and silver nanowires. Afterward, the foremost applications of CPs processed by 3D printing techniques in the biomedical and energy fields, that is, wearable electronics, sensors, soft robotics for human motion, or health monitoring devices, among others, will be discussed.

Regulating Lattice-Water-Adsorbed Ions to Optimize Intercalation Potential in 3D Prussian Blue Based Multi-Ion Microbattery

Miniaturized energy storage device (MESD) is the core module in microscale electronic equipment, yet its electrochemical performance is far away from the actual requirements. The extensive research efforts have improved the performance of MESD via the fabrication techniques and material construction, while ignoring the expansion of optimization strategy in the combination of energy storage mechanism. Herein, the Prussian blue/Zn microbattery is reported with the regulation of lattice-water-adsorbed intercalated ion. The optimal charge transport of cathode is achieved via the optimization of 3D structure of microelectrode to maximize the electrochemical performance. Also, lattice-water-adsorbed ion storage mechanism is further investigated to guide the design of differential energy storage for cathode and anode. The Cu₃ (Fe(CN)₆ )₂ /Zn microbattery, with K⁺ inter/deintercalation in the cathode and Zn²⁺ deplating/plating in the anode, displays high capacity (0.281 mAh cm^-2 at 2.5 mA cm^-2 ), rate performance (0.181 mAh cm^-2 at 25 mA cm^-2 ), and cycling stability (77.6% capacity retention after 1500 cycles) enhanced by Cu²⁺ in the electrolyte. This highly efficient combination of fabrication process, active material, and multi-ion storage for microelectrode shows a high tolerance for optimization strategies, expanding the compatibility of optimization path for high-performance MESD.

Multimodal cell with simultaneous electrochemical quartz crystal microbalance and in operando spectroscopic ellipsometry to understand thin film electrochemistry

To inform the development of advanced electrodes for energy storage, water treatment, and catalysis, among other applications, we need to improve our understanding of how material structure evolves during electrochemical operation. Insight into the evolution of local atomic structure during electrochemical operation is accessible through a range of sophisticated in operando probes, but techniques for in operando observation of macroscale electrode phenomena (e.g., swelling, dissolution, and chemical degradation) are limited. This macroscale understanding is critical to establish a full picture of electrochemical material behavior. Here, we report a multimodal cell for simultaneous electrochemical quartz crystal microbalance (EQCM) and in operando spectroscopic ellipsometry (SE). This SE-EQCM cell allows for the measurement of mass, thickness, optical properties, and electrochemical properties together in one device. Using polyaniline (PANI) as a test case, we demonstrate the use of this SE-EQCM cell to rapidly measure known phenomena and reproduce a range of prior results during the electrodeposition, electrochemical cycling, and electrochemical degradation of PANI. In particular, the simultaneous mass and thickness measurement afforded by this cell allows us to distinguish known qualitative differences in the degradation of PANI under oxidative and reductive potentials. The SE-EQCM cell we report promises to reveal new insights into the electrochemical behavior of thin film materials for a range of applications.

Anisotropic crystallite size distributions in LiFePO4 powders

The anisotropic crystallite sizes in high-performance LiFePO4 powders were measured by XRD and compared with the particle sizes found by TEM image analysis. Lognormal particle size distribution functions were determined for all three main crystallographic axes. A procedure was developed to determine the fraction of the composite particles which consists of several crystallites and contains small- and large-angle boundaries. In a sample with the most anisotropic crystallites (ratio of volume-weighted mean crystallite sizes L̄ V[001]/L̄ V[010] = 1.41) the number of the composite particles was at least 30%.

Graphene collage on Ni-rich layered oxide cathodes for advanced lithium-ion batteries

The energy storage performance of lithium-ion batteries (LIBs) depends on the electrode capacity and electrode/cell design parameters, which have previously been addressed separately, leading to a failure in practical implementation. Here, we show how conformal graphene (Gr) coating on Ni-rich oxides enables the fabrication of highly packed cathodes containing a high content of active material (~99 wt%) without conventional conducting agents. With 99 wt% LiNi_0.8Co_0.15Al_0.05O₂ (NCA) and electrode density of ~4.3 g cm^-3, the Gr-coated NCA cathode delivers a high areal capacity, ~5.4 mAh cm^-2 (~38% increase) and high volumetric capacity, ~863 mAh cm^-3 (~34% increase) at a current rate of 0.2 C (~1.1 mA cm^-2); this surpasses the bare electrode approaching a commercial level of electrode setting (96 wt% NCA; ~3.3 g cm^-3). Our findings offer a combinatorial avenue for materials engineering and electrode design toward advanced LIB cathodes.

Polyoxometalate-Templated Cobalt-Resorcin[4]arene Frameworks: Tunable Structure and Lithium-Ion Battery Performance

By employing a bowl-like tetra(benzimidazole)resorcin[4]arene (TBR4A) ligand, two new polyoxometalate-templated metal-organic frameworks (POMOFs), [Co₈Cl₁₄(TBR4A)₆]·3[H_3.3SiW₁₂O₄₀]·10DMF·11EtOH·20H₂O (1) and [Co₃Cl₂(TBR4A)₂(DMF)₄]·[SiW₁₂O₄₀]·2EtOH·3H₂O (2), have been prepared under solvothermal conditions (DMF = N,N'-dimethylformamide). 1 shows a 2D cationic layer, whereas 2 exhibits a 3D framework. Remarkably, the Keggin POMs in 1 and 2 were located in the cavities formed by two bowl-like resorcin[4]arenes in sandwich fashions. Their framework structures were highly dependent on the coordination modes of the TBR4A ligands. To increase the conductivity of POMOFs, the samples of 1 and 2 were loaded on the conductive polypyrrole-reduced graphene oxide (PPy-RGO) via ball milling (1@PG and 2@PG). Then, the obtained composites experienced calcination at a proper temperature to produce 1@PG-A and 2@PG-A. The resulting 1@PG-A and 2@PG-A composites, with improved conductivities, uniform sizes and micropores, exhibited promising electrochemical performance for lithium-ion batteries. We herein proposed a size-controlled route for the rational fabrication of functional POMOFs and their usage in energy fields.

Designing Spinel Li4Ti5O12 Electrode as Anode Material for Poly(ethylene)oxide-Based Solid-State Batteries

The development of a promising Li metal solid-state battery (SSB) is currently hindered by the instability of Li metal during electrodeposition; which is the main cause of dendrite growth and cell failure at elevated currents. The replacement of Li metal anode by spinel Li₄Ti₅O₁₂ (LTO) in SSBs would avoid such problems, endowing the battery with its excellent features such as long cycling performance, high safety and easy fabrication. In the present work, we provide an evaluation of the electrochemical properties of poly(ethylene)oxide (PEO)-based solid-state batteries using LTO as the active material. Electrode laminates have been developed and optimized using electronic conductive additives with different morphologies such as carbon black and multiwalled carbon nanotubes. The electrochemical performance of the electrodes was assessed on half-cells using a PEO-based solid electrolyte and a lithium metal anode. The optimized electrodes displayed an enhanced capability rate, delivering 150 mAh g⁻¹ at C/2, and a stable lifespan over 140 cycles at C/20 with a capacity retention of 83%. Moreover, postmortem characterization did not evidence any morphological degradation of the components after ageing, highlighting the long-cycling feature of the LTO electrodes. The present results bring out the opportunity to build high-performance solid-state batteries using LTO as anode material.