Adjacent single-atom irons boosting molecular oxygen activation on MnO2

Highly Dispersed Ni Atoms and O3 Promote Room-Temperature Catalytic Oxidation

Transition metal oxides are promising catalysts for catalytic oxidation reactions but are hampered by low room-temperature activities. Such low activities are normally caused by sparse reactive sites and insufficient capacity for molecular oxygen (O2) activation. Here, we present a dual-stimulation strategy to tackle these two issues. Specifically, we import highly dispersed nickel (Ni) atoms onto MnO2 to enrich its oxygen vacancies (reactive sites). Then, we use molecular ozone (O3) with a lower activation energy as an oxidant instead of molecular O2. With such dual stimulations, the constructed O3-Ni/MnO2 catalytic system shows boosted room-temperature activity for toluene oxidation with a toluene conversion of up to 98%, compared with the O3-MnO2 (Ni-free) system with only 50% conversion and the inactive O2-Ni/MnO2 (O3-free) system. This leap realizes efficient room-temperature catalytic oxidation of transition metal oxides, which is constantly pursued but has always been difficult to truly achieve.

In Situ Symbiosis of Cerium Oxide Nanophase for Enhancing the Oxygen Electrocatalysis Performance of Single-Atom Fe─N─C Catalyst with Prolonged Stability for Zinc-Air Batteries

The Fenton reaction, induced by the H2O2 formed during the oxygen reduction reaction (ORR) process leads to significant dissolution of Fe, resulting in unsatisfactory stability of the iron-nitrogen-doped carbon catalysts (Fe-NC). In this study, a strategy is proposed to improve the ORR catalytic activity while eliminating the effect of H2O2 by introducing CeO2 nanoparticles. Transmission electron microscopy and subsequent characterizations reveal that CeO2 nanoparticles are uniformly distributed on the carbon substrate, with atomically dispersed Fe single-atom catalysts (SACs) adjacent to them. CeO2@Fe-NC achieves a half-wave potential of 0.89 V and a limiting current density of 6.2 mA cm-2, which significantly outperforms Fe-NC and commercial Pt/C. CeO2@Fe-NC also shows a half-wave potential loss of only 1% after 10 000 CV cycles, which is better than that of Fe-NC (7%). Further, H2O2 elimination experiments show that the introduction of CeO2 significantly accelerate the decomposition of H2O2. In situ Raman spectroscopy results suggest that CeO2@Fe-NC significantly facilitates the formation of ORR intermediates compared with Fe-NC. The Zn-air batteries utilizing CeO2@Fe-NC cathodes exhibit satisfactory peak power density and open-circuit voltage. Furthermore, theoretical calculations show that the introduction of CeO2 enhances the ORR activity of Fe-NC SAC. This study provides insights for optimizing SAC-based electrocatalysts with high activity and stability.

Atomic Engineering of Single-Atom Nanozymes for Biomedical Applications

Single-atom nanozymes (SAzymes) showcase not only uniformly dispersed active sites but also meticulously engineered coordination structures. These intricate architectures bestow upon them an exceptional catalytic prowess, thereby captivating numerous minds and heralding a new era of possibilities in the biomedical landscape. Tuning the microstructure of SAzymes on the atomic scale is a key factor in designing targeted SAzymes with desirable functions. This review first discusses and summarizes three strategies for designing SAzymes and their impact on reactivity in biocatalysis. The effects of choices of carrier, different synthesis methods, coordination modulation of first/second shell, and the type and number of metal active centers on the enzyme-like catalytic activity are unraveled. Next, a first attempt is made to summarize the biological applications of SAzymes in tumor therapy, biosensing, antimicrobial, anti-inflammatory, and other biological applications from different mechanisms. Finally, how SAzymes are designed and regulated for further realization of diverse biological applications is reviewed and prospected. It is envisaged that the comprehensive review presented within this exegesis will furnish novel perspectives and profound revelations regarding the biomedical applications of SAzymes.

Advances in Synthesis and Applications of Single-Atom Catalysts for Metal Oxide-Based Gas Sensors

As a stable, low-cost, environment-friendly, and gas-sensitive material, semiconductor metal oxides have been widely used for gas sensing. In the past few years, single-atom catalysts (SACs) have gained increasing attention in the field of gas sensing with the advantages of maximized atomic utilization and unique electronic and chemical properties and have successfully been applied to enhance the detection sensitivity and selectivity of metal oxide gas sensors. However, the application of SACs in gas sensors is still in its infancy. Herein, we critically review the recent advances and current status of single-atom catalysts in metal oxide gas sensors, providing some suggestions for the development of this field. The synthesis methods and characterization techniques of SAC-modified metal oxides are summarized. The interactions between SACs and metal oxides are crucial for the stable loading of single-atom catalysts and for improving gas-sensitive performance. Then, the current application progress of various SACs (Au, Pt, Cu, Ni, etc.) in metal oxide gas sensors is introduced. Finally, the challenges and perspectives of SACs in metal oxide gas sensors are presented.

Graphdiyne/metal oxide hybrid materials for efficient energy and environmental catalysis

Graphdiyne (GDY)-based materials, owing to their unique structure and tunable electronic properties, exhibit great potential in the fields of catalysis, energy, environmental science, and beyond. In particular, GDY/metal oxide hybrid materials (GDY/MOs) have attracted extensive attention in energy and environmental catalysis. The interaction between GDY and metal oxides can increase the number of intrinsic active sites, facilitate charge transfer, and regulate the adsorption and desorption of intermediate species. In this review, we summarize the structure, synthesis, advanced characterization, small molecule activation mechanism and applications of GDY/MOs in energy conversion and environmental remediation. The intrinsic structure-activity relationship and corresponding reaction mechanism are highlighted. In particular, the activation mechanisms of reactant molecules (H2O, O2, N2, etc.) on GDY/MOs are systemically discussed. Finally, we outline some new perspectives of opportunities and challenges in developing GDY/MOs for efficient energy and environmental catalysis.

Engineering of Pore Design and Oxygen Vacancy on High-Entropy Oxides by a Microenvironment Tailoring Strategy

High-entropy oxides (HEOs) exhibit abundant structural diversity due to cationic and anionic sublattices with independence, rendering them superior in catalytic applications compared to monometallic oxides. Nevertheless, the conventional high-temperature calcination approach undermines the porosity and reduces the exposure of active sites (such as oxygen vacancies, OVs) in HEOs, leading to diminished catalytic efficiency. Herein, we fabricate a series of HEOs with a large surface area utilizing a microenvironment modulation strategy (m-NiMgCuZnCo: 86 m2/g, m-MnCuCoNiFe: 67 m2/g, and m-FeCrCoNiMn: 54 m2/g). The enhanced porosity in m-NiMgCuZnCo facilitates the presentation of numerous OVs, exhibiting an exceptional catalytic performance. This tactic creates inspiration for designing HEOs with rich porosity and active species with vast potential applications.

Bridging Atom Engineering for Low-Temperature Oxygen Activation in a Robust Metal-Organic Framework

Achieving active site engineering at the atomic level poses a significant challenge in the design and optimization of catalysts for energy-efficient catalytic processes, especially for a reaction with two reactants competitively absorbed on catalytic active sites. Herein, we show an example that tailoring the local environment of cobalt sites in a robust metal-organic framework through substituting the bridging atom from -Cl to -OH group leads to a highly active catalyst for oxygen activation in an oxidation reaction. Comprehensive characterizations reveal that this variation imparts drastic changes on the electronic structure of metal centers, the competitive reactant adsorption behavior, and the intermediate formation. As a result, exceptional low-temperature CO oxidation performance was achieved with T25(Temperature for 25 % conversion)=35 °C and T100 (Temperature for 100 % conversion)=150 °C, which stands out from existing MOF-based catalysts and even rivals many noble metal catalysts. This work provides a guidance for the rational design of catalysts for efficient oxygen activation for an oxidation reaction.

P-Bridging Asymmetry Diatomic Catalysts Sites Drive Efficient Bifunctional Oxygen Electrocatalysis for Zinc-Air Batteries

Rechargeable zinc-air batteries (ZABs) rely on the development of high-performance bifunctional oxygen electrocatalysts to facilitate efficient oxygen reduction/evolution reactions (ORR/OER). Single-atom catalysts (SACs), characterized by their precisely defined active sites, have great potential for applications in ZABs. However, the design and architecture of atomic site electrocatalysts with both high activity and durability present significant challenges, owing to their spatial confinement and electronic states. In this study, a strategy is proposed to fabricate structurally uniform dual single-atom electrocatalyst (denoted as P-FeCo/NC) consisting of P-bridging Fe and Co bimetal atom (i.e., Fe-P-Co) decorated on N, P-co-doped carbon framework as an efficient and durable bifunctional electrocatalyst for ZABs. Experimental investigations and theoretical calculations reveal that the Fe-P-Co bridge-coupling structure enables a facile adsorption/desorption of oxygen intermediates and low activation barrier. The resultant P-FeCo/NC exhibits ultralow overpotential of 340 mV at 10 mA cm-2 for OER and high half-wave potential of 0.95 V for ORR. In addition, the application of P-FeCo/NC in rechargeable ZABs demonstrates enhanced performance with maximum power density of 115 mW cm-2 and long cyclic stability, which surpass Pt/C and RuO2 catalysts. This study provides valuable insights into the design and mechanism of atomically dispersed catalysts for energy conversion applications.

Role of the In-Situ-Formed Surface (Pt-S-O)-Ti Active Structure in SO2-Promoted C3H8 Combustion over a Pt/TiO2 Catalyst

Typically, SO2 unavoidably deactivates catalysts in most heterogeneous catalytic oxidations. However, for Pt-based catalysts, SO2 exhibits an extraordinary boosting effect in propane catalytic oxidation, but the promotive mechanism remains contentious. In this study, an in situ-formed tactful (Pt-S-O)-Ti structure was concluded to be a key factor for Pt/TiO2 catalysts with a substantial SO2 tolerance ability. The experiments and theoretical calculations confirm that the high degree of hybridization and orbital coupling between Pt 5d and S 3p orbitals enable more charge transfer from Pt to S species, thus forming the (Pt-S-O)-Ti structure with the oxygen atom dissociated from the chemisorbed O2 adsorbed on oxygen vacancies. The active oxygen atom in the (Pt-S-O)-Ti active structure is a robust site for C3H8 adsorption, leading to a better C3H8 combustion performance. This work can provide insights into the rational design of chemical bonds for high SO2 tolerance catalysts, thereby improving economic and environmental benefits.

Rare earth oxide based electrocatalysts: synthesis, properties and applications

As an important strategic resource, rare earths (REs) constitute 17 elements in the periodic table, namely 15 lanthanides (Ln) (La-Lu, atomic numbers from 57 to 71), scandium (Sc, atomic number 21) and yttrium (Y, atomic number 39). In the field of catalysis, the localization and incomplete filling of 4f electrons endow REs with unique physical and chemical properties, including rich electronic energy level structures, variable coordination numbers, etc., making them have great potential in electrocatalysis. Among various RE catalytic materials, rare earth oxide (REO)-based electrocatalysts exhibit excellent performances in electrocatalytic reactions due to their simple preparation process and strong structural variability. At the same time, the electronic orbital structure of REs exhibits excellent electron transfer ability, which can reduce the band gap and energy barrier values of rate-determining steps, further accelerating the electron transfer in the electrocatalytic reaction process; however, there is a lack of systematic review of recent advances in REO-based electrocatalysis. This review systematically summarizes the synthesis, properties and applications of REO-based nanocatalysts and discusses their applications in electrocatalysis in detail. It includes the hydrogen evolution reaction (HER), oxygen evolution reaction (OER), hydrogen oxidation reaction (HOR), oxygen reduction reaction (ORR), carbon dioxide reduction reaction (CO2RR), methanol oxidation reaction (MOR), nitrogen reduction reaction (NRR) and other electrocatalytic reactions and further discusses the catalytic mechanism of REs in the above reactions. This review provides a timely and comprehensive summary of the current progress in the application of RE-based nanomaterials in electrocatalytic reactions and provides reasonable prospects for future electrocatalytic applications of REO-based materials.

Anderson-type polyoxometalate-based metal-organic framework as an efficient heterogeneous catalyst for selective oxidation of benzylic C-H bonds

Oxidative transformation of benzylic C-H bonds into functional carbonyl groups under mild conditions represents an efficient method for the synthesis of aromatic carboxylic acids and ketones. Here we report a high-efficiency catalyst system constructed from an Anderson-type polyoxometalate-based metal-Organic framework (POMOF-1) and N-hydroxyphthalimide (NHPI) for selective oxidation of methylarenes and alkylarenes under 1 atm O2 atmosphere. POMOF-1 exerted a synergistic effect originating from the well-aligned Anderson {CrMo6} clusters and Cu centers within the framework, and this entailed good cooperation with NHPI to catalyze the selective oxidation. Accordingly, the reactions exhibit good tolerance and chemical selectivity for a wide range of substrates bearing diverse substituent groups, and the corresponding carboxylic acids and ketones were harvested in good yields under mild conditions. Mechanism study reveals that POMOF-1 worked synergistically with NPHI to activate the benzylic C-H bonds of substrates, which are sequentially oxidized by oxygen and HOO˙ to give rise to the products. This work may pave a way to design high-efficiency catalysts by integration of polyoxometalate-based materials with NPHI for challenging C-H activation.

Electron Donation from Boron Suboxides via Strong p-d Orbital Hybridization Boosts Molecular O2 Activation on Ru/TiO2 for Low-Temperature Dibromomethane Oxidation

Low-temperature catalytic oxidation is of significance to the degradation of halogenated volatile organic compounds (HVOCs) to avoid hazardous byproducts with low energy consumption. Efficient molecular oxygen (O2) activation is pivotal to it but usually limited by the insufficient electron cloud density at the metal center. Herein, Ru-B catalysts with enhanced electron density around Ru were designed to achieve efficient O2 activation, realizing dibromomethane (DBM) degradation T90 at 182 °C on RuB1/TiO2 (about 30 °C lower than pristine Ru/TiO2) with a TOFRu value of 0.055 s-1 (over 8 times that of Ru/TiO2). Compared to the limited electron transfer (0.02 e) on pristine Ru/TiO2, the Ru center gained sufficient negative charges (0.31 e) from BOx via strong p-d orbital hybridization. The Ru-B site then acted as the electron donor complexing with the 2π* antibonding orbital of O2 to realize the O2 dissociative activation. The reactive oxygen species formed thereby could initiate a fast conversion and oxidation of formate intermediates, thus eventually boosting the low-temperature catalytic activity. Furthermore, we found that the Ru-B sites for O2 activation have adaptation for pollutant removal and multiple metal availability. Our study shed light on robust O2 activation catalyst design based on electron density adjustment by boron.

Constructing Active Cu2+-O-Fe3+ Sites at the CuO-Fe3O4 Interface to Promote Activation of Surface Lattice Oxygen

Activating surface lattice oxygen (Olatt) through the modulation of metal-oxygen bond strength has proven to be an effective route for facilitating the catalytic degradation of volatile organic compounds (VOCs). Although this strategy has been implemented via the construction of the TM1-O-TM2 (TM represents a transition metal) structure in various reactions, the underlying principle requires exploration when using different TMs. Herein, the Cu2+-O-Fe3+ structure was created by developing CuO-Fe3O4 composites with enhanced interfacial effect, which exhibited superior catalytic activity to their counterparts, with T90 (the temperature of toluene conversion reaching 90%) decreasing by approximately 50 °C. Structural analyses and theoretical calculations demonstrated that the active Cu2+-O-Fe3+ sites at the CuO-Fe3O4 interface improved low-temperature reducibility and oxygen species activity. Particularly, X-ray absorption fine structure spectroscopy revealed the contraction and expansion of Cu-O and Fe-O bonds, respectively, which were responsible for the activation of the surface Olatt. A mechanistic study revealed that toluene can be oxidized by rapid dehydrogenation of methyl assisted by the highly active surface Olatt and subsequently undergo ring-opening and deep mineralization into CO2 following the Mars-van Krevelen mechanism. This study provided a novel strategy to explore interface-enhanced TM catalysts for efficient surface Olatt activation and VOCs abatement.

Spatially Separated Active Sites Enable Selective CO Oxidation Reaction on Oxide Catalyst

The search for efficient non-noble-metal catalysts able to perform selective oxidation reactions is of great importance, with relevance to many catalytic processes. However, this is often hampered because the origin of the selectivity remains controversial, particularly for reactions catalyzed by oxides. Here, combining high-pressure surface imaging techniques and theoretical calculations, we identify that spatially separated active sites for O2 activation and H2 adsorption on an ultrathin Mn3O4 surface enable selective oxidation of CO over H2. Theoretical calculations reveal that Mn-O pairs for H2 dissociation are separated from Mn-Mn pairs for the formation of adsorbed O2* so that H2 has to surmount much higher barriers for both H2 dissociation and H diffusion while CO can directly react with O2* following the Eley-Rideal process. Our study sheds light on the atomic-level understanding of the surface structure-dependent selective oxidation reaction on oxide catalysts.

Surface oxygen vacancy-dependent molecular oxygen activation for propane combustion over α-MnO2

Oxygen vacancies (OV), as the sites of molecular oxygen adsorption and activation, play an important role in the catalytic combustion process of volatile organic compounds (VOCs). Revealing the relationship between OV concentration and molecular oxygen activation behavior is of significance to construct the efficient catalysts. Herein, α-MnO2 with different OV concentrations was prepared to investigate the molecular oxygen activation for C3H8 combustion. It is disclosed that the enhanced OV concentration in α-MnO2 induced the reconfiguration of surface metal atoms, resulting in the transformation of oxygen activation configuration from end-on mode to side-on mode. Oxygen molecules in side-on mode possessed more localized electron density and weaker coordination bond strength with surrounding Mn atoms, which were more favorable to adsorb C3H8 molecules and activate C-H bond for the improved combustion performance. This work provides a new understanding to reveal that the increased OV concentration contributes to more efficient VOCs combustion.

Dual-Active-Sites Single-Atom Catalysts for Advanced Applications

Dual-Active-Sites Single-Atom catalysts (DASs SACs) are not only the improvement of SACs but also the expansion of dual-atom catalysts. The DASs SACs contains dual active sites, one of which is a single atomic active site, and the other active site can be a single atom or other type of active site, endowing DASs SACs with excellent catalytic performance and a wide range of applications. The DASs SACs are categorized into seven types, including the neighboring mono metallic DASs SACs, bonded DASs SACs, non-bonded DASs SACs, bridged DASs SACs, asymmetric DASs SACs, metal and nonmetal combined DASs SACs and space separated DASs SACs. Based on the above classification, the general methods for the preparation of DASs SACs are comprehensively described, especially their structural characteristics are discussed in detail. Meanwhile, the in-depth assessments of DASs SACs for variety applications including electrocatalysis, thermocatalysis and photocatalysis are provided, as well as their unique catalytic mechanism are addressed. Moreover, the prospects and challenges for DASs SACs and related applications are highlighted. The authors believe the great expectations for DASs SACs, and this review will provide novel conceptual and methodological perspectives and exciting opportunities for further development and application of DASs SACs.

Modulating paired Ir-O-Ir via electronic perturbations of correlated Ir single atoms to overcome catalytic selectivity

Single-atom catalysts have been extensively utilized for electrocatalysis, in which electronic metal-support interactions are typically employed to stabilize single atoms. However, this neglects the metal-metal interactions of adjacent atoms, which are essential for the fine-tuning of selective sites. Herein, the high-loading of Ir single atoms (Ir SAs) (8.9 wt%) were adjacently accommodated into oxygen vacancy-rich Co3O4 nanosheets (Ir SAs/Co3O4). Electronic perturbations for both Ir single atoms and Co3O4 supports were observed under electronic metal-support and metal-metal interactions, thus generating Ir-O-Co/Ir units. Electrons were transferred from Co and Ir to O atoms, inducing the depletion of 3d/5d states in Co/Ir and the occupation of 2p states in O atoms to stabilize the Ir SAs. Moreover, the O atoms of Ir-O-Ir functioned as the main active sites for the electrocatalysis of As(iii), which reduced the energy barrier for the rate-determining step. This was due to the stronger electronic affinities for intermediates from reduction of As(iii), which were completely distinct from other coordinated O atoms of Co3O4 or IrO2. Consequently, the resultant Ir SAs/Co3O4 exhibited far more robust electrocatalytic activities than IrO2/Co3O4 and Co3O4 in the electrocatalysis of As(iii). Moreover, there was a strong orbital coupling effect between the coordinated O atoms of Ir SAs and the -OH of H3AsO3, thus exhibiting superior selectivity for As(iii) in contrast to other common heavy metal cations. This work offers useful insights into the rational design of intriguing SACs with high selectivity and stability for the electrocatalysis and electrochemical analysis of pollutants on an electronic level.

Constructing N,S and N,P Co-Coordination in Fe Single-Atom Catalyst for High-Performance Oxygen Redox Reaction

Single-atom catalysts (SACs) are promising electrocatalysts for the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER), in which the coordination environment plays a crucial role in activating the intrinsic activity of the central metal. Taking the FeN4 SAC as a probe, this work investigates the effect of introducing S or P atoms into N coordination (FeSx N4-x and FePx N4-x (x=1-4)) on the electronic structure optimization of Fe center and its catalytic performance. Attributing to the optimal Fe 3d orbitals, FePN3 can effectively activate O2 and promote ORR with a low overpotential of 0.29 V, surpassing FeN4 and most reported catalysts. FeSN3 is beneficial to H2 O activation and OER, proceeding with an overpotential of 0.68 V, which is superior to FeN4 . Both FePN3 and FeSN3 exhibit outstanding thermodynamic and electrochemical stability with negative formation energies and positive dissolution potentials. Hence, the N,P and N,S co-coordination might provide better catalytic environment than regular N coordination for SACs in ORR and OER. This work demonstrates FePN3 /FeSN3 as high-performance ORR/OER catalysts and highlights N,P and N,S co-coordination regulation as an effective approach to fine tune high atomically dispersed electrocatalysts.

Enhancing polyol/sugar cascade oxidation to formic acid with defect rich MnO2 catalysts

Oxidation of renewable polyol/sugar into formic acid using molecular O₂ over heterogeneous catalysts is still challenging due to the insufficient activation of both O₂ and organic substrates on coordination-saturated metal oxides. In this study, we develop a defective MnO₂ catalyst through a coordination number reduction strategy to enhance the aerobic oxidation of various polyols/sugars to formic acid. Compared to common MnO₂, the tri-coordinated Mn in the defective MnO₂ catalyst displays the electronic reconstruction of surface oxygen charge state and rich surface oxygen vacancies. These oxygen vacancies create more Mn^δ+ Lewis acid site together with nearby oxygen as Lewis base sites. This combined structure behaves much like Frustrated Lewis pairs, serving to facilitate the activation of O₂, as well as C-C and C-H bonds. As a result, the defective MnO₂ catalyst shows high catalytic activity (turnover frequency: 113.5 h^-1) and formic acid yield (>80%) comparable to noble metal catalysts for glycerol oxidation. The catalytic system is further extended to the oxidation of other polyols/sugars to formic acid with excellent catalytic performance.

Cobalt-Nitrogen Co-Doped Carbon as Highly Efficient Oxidase Mimics for Colorimetric Assay of Nitrite

Transition metal-N-doped carbon has been demonstrated to mimic natural enzyme activity; in this study, cobalt-nitrogen co-doped carbon (Co-N-C) nanomaterial was developed, and it could be an oxidase mimic. Firstly, Co-N-C with oxidase-like activity boosts the chromogenic reaction of 3,3',5,5'-tetramethylbenzidine (TMB) to produce the oxidized TMB (oxTMB). And the aromatic primary amino group of oxTMB reacts with nitrite (NO₂^-) to form diazo groups. Based on this background, we developed a cascade system of a Co-N-C-catalyzed oxidation reaction and a diazotization reaction for nitrite determination. The low detection limit (0.039 μM) indicates that Co-N-C is superior compared with the vast majority of previously reported nitrite assays. This study not only provides a novel nanozyme with sufficiently dispersed active sites, but it also further applies it to the determination of nitrite, which is expected to expand the application of nanozymes in colorimetric analysis.

Fe-N-C catalysts decorated with oxygen vacancies-rich CeOx to increase oxygen reduction performance for Zn-air batteries

Platinum group metal (PGM)-free catalysts represented by nitrogen and iron co-doped carbon (Fe-N-C) catalysts are desirable and critical for metal-air batteries, but challenges still exist in performance and stability. Here, cerium oxides (CeO_x) are incorporated into a two-dimensional Fe-N-C catalyst (FeNC-Ce-950) via a host-guest strategy. The Ce⁴⁺/Ce³⁺ redox system creates a large number of oxygen vacancies for rapid O₂ adsorption to accelerate the kinetics of oxygen reduction reaction (ORR). Consequently, the as-synthesized FeNC-Ce-950 catalyst exhibits a half-wave potential (E_1/2) of 0.921 V and negligible decay (<2 mV for ΔE_1/2) after 5,000 accelerated durability cycles, significantly outperforming most of ORR catalysts reported in recent years and precious metal counterparts. When applied in a zinc-air battery, it demonstrates a peak power density of 175 mW cm^-2 and a specific capacity of 757 mAh g_Zn^-1. This study also provides a reference for the exploration of Fe-N-C catalysts decorated with variable valence metal oxides.

Nanostructured Carbon Nitride for Continuous-Flow Trifluoromethylation of (Hetero)arenes

Efficient catalytic methods for the trifluoromethylation of (hetero)arenes are of particular importance in organic and pharmaceutical manufacturing. However, many existing protocols rely on toxic reagents and expensive or sterically hindered homogeneous catalysts. One promising alternative to conduct this transformation involves the use of carbon nitride, a non-toxic photocatalyst prepared from inexpensive precursors. Nonetheless, there is still little understanding regarding the interplay between physicochemical features of this photocatalyst and the corresponding effects on the reaction rate. In this work, we elucidate the role of carbon nitride nanostructuring on the catalytic performance, understanding the effect of surface area and band gap tuning via metal insertion. Our findings provide new insights into the structure-function relationships of the catalyst, which we exploit to design a continuous-flow process that maximizes catalyst-light interaction, facilitates catalyst reusability, and enables intensified reaction scale-up. This is particularly significant given that photocatalyzed batch protocols often face challenges during industrial exploitation. Finally, we extrapolate the rapid and simplified continuous-flow method to the synthesis of a variety of functionalized heteroaromatics, which have numerous applications in the pharmaceutical and fine chemical industries.

Highly Selective Transformation of Biomass Derivatives to Valuable Chemicals by Single-Atom Photocatalyst Ni/TiO2

Selective CC cleavage of the biomass derivative glycerol under mild conditions is recognized as a promising yet challenging synthesis route to produce value-added chemicals. Here, a highly selective catalyst for the transformation of glycerol to the high-value product glycolaldehyde is presented, which is composed of nickel single atoms confined to the surface of titanium dioxide. Driven by light, the catalyst operates under ambient conditions using air as a green oxidant. The optimized catalyst shows a selectivity of over 60% to glycolaldehyde, resulting in 1058 µmol g_Cat ^-1  h^-1 production rate, and ≈3 times higher turnover number than NiO_x -nanoparticle-decorated TiO₂ photocatalyst. Diverse operando and in situ spectroscopies unveil the unique function of the Ni single atom, which can significantly promote oxygen adsorption, work as an electron sink, and accelerate the production of superoxide radicals, thereby improving the selectivity toward glycolaldehyde over other by-products.

Effect of MnO2 Crystal Type on the Oxidation of Furfural to Furoic Acid

The base-free oxidation of furfural by non-noble metal systems has been challenging. Although MnO2 emerges as a potential catalyst application in base-free conditions, its catalytic efficiency still needs to be improved. The crystalline form of MnO2 is an important factor affecting the oxidation ability of furfural. For this reason, four crystalline forms of MnO2 (α, β, γ, and δ-MnO2) were selected. Their oxidation performance and surface functional groups were analyzed and compared in detail. Only δ-MnO2 exhibited excellent activity, achieving 99.04% furfural conversion and 100% Propo.FA (Only furoic acid was detected by HPLC in the product) under base-free conditions, while the furfural conversion of α, β, and γ-MnO2 was below 10%. Characterization by XPS, IR, O2-TPD and other means revealed that δ-MnO2 has the most abundant active oxygen species and surface hydroxyl groups, which are responsible for the best performance of δ-MnO2. This work achieves the green and efficient oxidation of furfural to furoic acid over non-noble metal catalysts.

Spontaneous Formation of Low Valence Copper on Red Phosphorus to Effectively Activate Molecular Oxygen for Advanced Oxidation Process

Efficient spontaneous molecular oxygen (O₂) activation is an important technology in advanced oxidation processes. Its activation under ambient conditions without using solar energy or electricity is a very interesting topic. Low valence copper (LVC) exhibits theoretical ultrahigh activity toward O₂. However, LVC is difficult to prepare and suffers from poor stability. Here, we first report a novel method for the fabrication of LVC material (P-Cu) via the spontaneous reaction of red phosphorus (P) and Cu²⁺. Red P, a material with excellent electron donating ability and can directly reduce Cu²⁺ in solution to LVC via forming Cu-P bonds. With the aid of the Cu-P bond, LVC maintains an electron-rich state and can rapidly activate O₂ to produce ·OH. By using air, the ·OH yield reaches a high value of 423 μmol g^-1 h^-1, which is higher than traditional photocatalytic and Fenton-like systems. Moreover, the property of P-Cu is superior to that of classical nano-zero-valent copper. This work first reports the concept of spontaneous formation of LVC and develops a novel avenue for efficient O₂ activation under ambient conditions.

DFT-Based Study for the Enhancement of CO2 Adsorption on Metal-Doped Nitrogen-Enriched Polytriazines

Nitrogen-enriched polytriazine (NPT), a carbon nitride-based material, has received much attention for CO₂ storage applications. However, to enhance the CO₂ uptake capacity more efficiently, it is necessary to understand the interaction mechanism between CO₂ molecules and NPT through appropriate modification of the structures. Here, we introduce a method to enhance the CO₂ adsorption capacity of NPT by incorporating metal atoms such as Sn, Co, and Ni into the polytriazine network. DFT calculations were used to investigate the CO₂ adsorption mechanism of the polytriazine frameworks by tracking the interactions between CO₂ and the various interaction sites of NPT. By optimizing the geometry of the pure and metal-containing NPT frameworks, we calculated the binding energy of metal atoms in the NPT framework, the adsorption energy of CO₂ molecules, and the charge transfer between CO₂ molecules and the corresponding adsorption systems. In this work, we demonstrate that the CO₂ adsorption capacity of NPT can be greatly enhanced by doping transition-metal atoms into the cavities of NPT.

Enhancing the activity of Pd ensembles on graphene by manipulating coordination environment

Atomic dispersion of metal catalysts on a substrate accounts for the increased atomic efficiency of single-atom catalysts (SACs) in various catalytic schemes compared to the nanoparticle counterparts. However, lacking neighboring metal sites has been shown to deteriorate the catalytic performance of SACs in a few industrially important reactions, such as dehalogenation, CO oxidation, and hydrogenation. Metal ensemble catalysts (Mn), an extended concept to SACs, have emerged as a promising alternative to overcome such limitation. Inspired by the fact that the performance of fully isolated SACs can be enhanced by tailoring their coordination environment (CE), we here evaluate whether the CE of Mn can also be manipulated in order to enhance their catalytic activity. We synthesized a set of Pd ensembles (Pdn) on doped graphene supports (Pdn/X-graphene where X = O, S, B, and N). We found that introducing S and N onto oxidized graphene modifies the first shell of Pdn converting Pd-O to Pd-S and Pd-N, respectively. We further found that the B dopant significantly affected the electronic structure of Pdn by serving as an electron donor in the second shell. We examined the performance of Pdn/X-graphene toward selective reductive catalysis, such as bromate reduction, brominated organic hydrogenation, and aqueous-phase CO2 reduction. We observed that Pdn/N-graphene exhibited superior performance by lowering the activation energy of the rate-limiting step, i.e., H2 dissociation into atomic hydrogen. The results collectively suggest controlling the CE of SACs in an ensemble configuration is a viable strategy to optimize and enhance their catalytic performance.

Dual Molecular Oxygen Activation Sites on Conjugated Microporous Polymers for Enhanced Photocatalytic Formation of Benzothiazoles

Oxidative formation of high value compounds involving active oxygen species using heterogeneous polymeric photocatalysts has become a useful tool in catalysis. Controlling the interaction between the active sites on polymer photocatalysts and oxygen molecules is still challenging due to the rather large polymer backbone structure. Here, we design a triazine-containing donor acceptor-type conjugated microporous polymer (CMP) containing dual major active sites at F and N atoms for molecular oxygen activation. Introducing fluorine atoms on the CMP backbone led to a combined effect of enhanced adsorption and electron transfer of oxygen. Time-resolved photoluminescence, electronic paramagnetic resonance spectra, and DFT calculation revealed favorable absorption energy and electron transfer kinetics between the CMP and oxygen molecules, thus efficiently generating superoxide radicals (O₂^•-) and singlet oxygen (¹O₂) as main active oxygen species. The photocatalytic activity, selectivity, and reusability of the CMP was demonstrated by the photocatalytic formation of a variety of benzothiazoles.

Rhodium Single-Atom Catalyst Design through Oxide Support Modulation for Selective Gas-Phase Ethylene Hydroformylation

A frontier challenge in single-atom (SA) catalysis is the design of fully inorganic sites capable of emulating the high reaction selectivity traditionally exclusive of organometallic counterparts in homogeneous catalysis. Modulating the direct coordination environment in SA sites, via the exploitation of the oxide support's surface chemistry, stands as a powerful albeit underexplored strategy. We report that isolated Rh atoms stabilized on oxygen-defective SnO₂ uniquely unite excellent TOF with essentially full selectivity in the gas-phase hydroformylation of ethylene, inhibiting the thermodynamically favored olefin hydrogenation. Density Functional Theory calculations and surface characterization suggest that substantial depletion of the catalyst surface in lattice oxygen, energetically facile on SnO₂ , is key to unlock a high coordination pliability at the mononuclear Rh centers, leading to an exceptional performance which is on par with that of molecular catalysts in liquid media.

Cost-Effective H2 O2 -Regeneration of Powdered Activated Carbon by Isolated Fe Sites

The reuse of powdered activated carbon (PAC) vitally determines the economics and security of the PAC-based adsorption process, while state-of-the-art PAC regeneration technologies are usually unsatisfactory. Here, it is demonstrated that isolated Fe sites anchored on commercial PAC enable fast H₂ O₂ activation to produce Fe-based reactive oxygen species for highly efficient PAC regeneration at room temperature. Taking rhodamine B as a representative pollutant, PAC decorated with isolated Fe sites realize H₂ O₂ based regeneration with negligible adsorption capacity degradation for 10 cycles. Moreover, in terms of the PAC loss rate, this technology is greatly superior to traditional Fenton-based regeneration technology. Further operando experiments and theoretical calculations reveal that the high regeneration performance can be attributed to the isolated HOFeO motifs, which activate H₂ O₂ via a nonradical reaction pathway. These findings provide a very promising strategy toward reducing the cost of H₂ O₂ -based PAC regeneration technology.

Progress and Perspectives of Single-Atom Catalysts for Gas Sensing

Single-atom catalysts (SACs) attract extensive attention in the field of heterogeneous catalysis in recent years due to the maximum atom utilization and unique physical and chemical properties. The gas sensing is actually a heterogeneous catalysis process but the SACs are new to this area. Although SACs show huge potential in gas sensing, the SACs gas sensing area currently is still at the infancy stage. This work critically reviews the recent advances and current status of single-atom gas sensing materials. General synthesis routes, characterization methods, and sensing performance indexes are introduced. At the end, the challenges and future prospects on SACs gas sensing are presented from the authors' perspectives. This work is anticipated to provide insights and guideline for the chemical sensing community.

Insight into the Effect of Oxygen Vacancy Prepared by Different Methods on CuO/Anatase Catalyst for CO Catalytic Oxidation

In this study, CuO loaded on anatase TiO2 catalysts (CuO/anatase) with oxygen vacancies was synthesized via reduction treatments by NaHB4 and H2 (CuO/anatase-B, CuO/anatase-H), respectively. The characterizations suggest that different reduction treatments bring different concentration of oxygen vacancies in the CuO/anatase catalysts, which finally affect the CO catalytic performance. The CuO/anatase-B and CuO/anatase-H exhibit CO conversion of 90% at 182 and 198 °C, respectively, which is lower than what occurred for CuO/anatase (300 °C). The XRD, Raman, and EPR results show that the amount of the oxygen vacancies of the CuO/anatase-H is the largest, indicating a stronger reduction effect of H2 than NaHB4 on the anatase surface. The in situ DRIFTS results exhibit that the Cu sites are the adsorption sites of CO, and the oxygen vacancies on the anatase can active the O2 molecules into reactive oxygen species. According to the in situ DRIFTS results, it can be concluded that in the CO oxidation reaction, only the CuO/anatase-H catalyst can be carried out by the Mvk mechanism, which greatly improves its catalytic efficiency. This study explained the reaction mechanisms of CO oxidation on various anatase surfaces, which offers detailed insights into how to prepare suitable catalysts for low-temperature oxidation reactions.

Surface and Interface Coordination Chemistry Learned from Model Heterogeneous Metal Nanocatalysts: From Atomically Dispersed Catalysts to Atomically Precise Clusters

The surface and interface coordination structures of heterogeneous metal catalysts are crucial to their catalytic performance. However, the complicated surface and interface structures of heterogeneous catalysts make it challenging to identify the molecular-level structure of their active sites and thus precisely control their performance. To address this challenge, atomically dispersed metal catalysts (ADMCs) and ligand-protected atomically precise metal clusters (APMCs) have been emerging as two important classes of model heterogeneous catalysts in recent years, helping to build bridge between homogeneous and heterogeneous catalysis. This review illustrates how the surface and interface coordination chemistry of these two types of model catalysts determines the catalytic performance from multiple dimensions. The section of ADMCs starts with the local coordination structure of metal sites at the metal-support interface, and then focuses on the effects of coordinating atoms, including their basicity and hardness/softness. Studies are also summarized to discuss the cooperativity achieved by dual metal sites and remote effects. In the section of APMCs, the roles of surface ligands and supports in determining the catalytic activity, selectivity, and stability of APMCs are illustrated. Finally, some personal perspectives on the further development of surface coordination and interface chemistry for model heterogeneous metal catalysts are presented.

In Situ Fabrication of Highly Dispersed Co-Fe-Doped-δ-MnO2 Catalyst by a Facile Redox-Driving MOFs-Derived Method for Low-Temperature Oxidation of Toluene

Cost-efficient and durable manganese-based catalysts are in great demand for the catalytic elimination of volatile organic compounds (VOCs), which are dominated not only by the nanostructures but also by the oxygen vacancies and Mn-O bond in the catalysts. Herein, a series of nanostructured Co-Fe-doped-δ-MnO₂ catalysts (Co-Fe-δ-MnO₂) with high dispersion were in situ fabricated by employing metal-organic-frameworks (MOFs) as reducing agents, dopants, and templates all at the same time. The as-obtained Co-Fe-δ-MnO₂-20% catalyst exhibited robust durability and high catalytic activity (225 °C) for toluene combustion even in the presence of 5 vol % water vapor, which is 50 °C lower than that of pristine δ-MnO₂. Various characterizations revealed that the homogeneously dispersed codoping of Co and Fe ions into δ-MnO₂ promotes the generation of oxygen vacancies and weakens the strength of the Mn-O bond, thus increasing the amount of adsorbed oxygen (O_ads) and improving the mobility of lattice oxygen (O_latt). Meanwhile, due to successfully inheriting the framework structures of MOFs, the obtained catalyst exhibited a high surface area and three-dimensional mesoporous structure, which contributes to diffusion and increases the number of active sites. Moreover, in situ DRIFTS results confirmed that the toluene degradation mechanism on the Co-Fe-δ-MnO₂-20% follows the MVK mechanism and revealed that more O_ads and high-mobility O_latt induced by this novel method contribute to accumulating and mineralizing key intermediates (benzoate) and thus promote toluene oxidation. In conclusion, this work stimulates the opportunities to develop Co-Fe-δ-MnO₂ as a class of nonprecious-metal-based catalysts for controlling VOC emissions.

Single-atom site catalysts for environmental remediation: Recent advances

Single-atom site catalysts (SACs) can maximize the utilization of active metal species and provide an attractive way to regulate the activity and selectivity of catalytic reactions. The adjustable coordination configuration and atomic structure of SACs enable them to be an ideal candidate for revealing reaction mechanisms in various catalytic processes. The minimum use of metals and relatively tight anchoring of the metal atoms significantly reduce leaching and environmental risks. Additionally, the unique physicochemical properties of single atom sites endow SACs with superior activity in various catalytic processes for environmental remediation (ER). Generally, SACs are burgeoning and promising materials in the application of ER. However, a systematic and critical review on the mechanism and broad application of SACs-based ER is lacking. Herein, we review emerging studies applying SACs for different ERs, such as eliminating organic pollutants in water, removing volatile organic compounds, purifying automobile exhaust, and others (hydrodefluorination and disinfection). We have summarized the synthesis, characterization, reaction mechanism and structural-function relationship of SACs in ER. In addition, the perspectives and challenges of SACs for ER are also analyzed. We expect that this review can provide constructive inspiration for discoveries and applications of SACs in environmental catalysis in the future.

Mo Vacancy-Mediated Activation of Peroxymonosulfate for Ultrafast Micropollutant Removal Using an Electrified MXene Filter Functionalized with Fe Single Atoms

Developing advanced heterogeneous catalysts with atomically dispersed active sites is an efficient strategy to boost the kinetics of peroxymonosulfate (PMS) activation for micropollutant removal. Here, we report a binary Mo₂TiC₂T_x MXene-based electroactive filter system with abundant surface Mo vacancies for effective activation of PMS. The Mo vacancies assumed two essential roles: (i) as anchoring sites for Fe single atoms (Fe-SA) and (ii) as cocatalytic sites for the Fenton-like reaction. Fe-SA formed strong metal-oxygen bonds with the Mo₂TiC₂T_x support, stabilizing at the sites previously occupied by Mo. The resulting Fe-SA/Mo₂TiC₂T_x nanohybrid filter achieved 100% degradation of sulfamethoxazole (SMX) in the single-pass mode (hydraulic retention time <2 s) when assisted by an electric field (2.0 V). The rate constant (k = 2.89 min^-1) for SMX removal was 24 and 67 times greater than that of Fe nanoparticles immobilized on Mo₂TiC₂T_x and the pristine Mo₂TiC₂T_x filter, respectively. Operation in the flow-through configuration outperformed the conventional batch reactor model (k = 0.17 min^-1) due to convection-enhanced mass transport. The results obtained from experimental investigations and theoretical calculations suggested that atomically dispersed Fe-SA, anchored on Mo vacancies, was responsible for the adsorption and activation of PMS to produce sulfate radicals (SO₄^•-) in the presence of an electric field. This study provides a proof-of-concept demonstration of an electroactive Fe-SA/Mo₂TiC₂T_x filter for broader application in the treatment of water contaminated by emerging micropollutants.

A Site Distance Effect Induced by Reactant Molecule Matchup in Single-Atom Catalysts for Fenton-Like Reactions

Understanding the site interaction nature of single-atom catalysts (SACs), especially densely populated SACs, is vital for their application to various catalytic reactions. Herein, we report a site distance effect, which emphasizes how well the distance of the adjacent copper atoms (denoted as d_Cu1-Cu1 ) matches with the reactant peroxydisulfate (PDS) molecular size to determine the Fenton-like reaction reactivity on the carbon-supported SACs. The optimized d_Cu1-Cu1 in the range of 5-6 Å, which matches the molecular size of PDS, endows the catalyst with a nearly two times higher turnover frequency than that of d_Cu1-Cu1 beyond this range, accordingly achieving record-breaking kinetics for the oxidation of emerging organic contaminants. Further studies suggest that this site distance effect originates from the alteration of PDS adsorption to a dual-site structure on Cu₁ -Cu₁ sites when d_Cu1-Cu1 falls within 5-6 Å, significantly enhancing the interfacial charge transfer and consequently resulting in the most efficient catalyst for PDS activation so far.

Catalytic Oxygen Activation over the Defective CuO Nanoparticles for Ultrafast Dehalogenation

The nucleophilic superoxide radical (O₂^•-)-based dehalogenation reaction shows great potential to degrade the toxic halogenated organic compounds (HOCs). But such an O₂^•--mediated reductive reaction often suffers from the competition of the secondary oxidative species (e.g., •OH), leading to inferior electron efficiency and possible disinfection byproduct formation. Here, an O₂^•--dominant ultrafast dehalogenation system is developed via molecular O₂ activation by the oxygen vacancy (OV)-rich CuO nanoparticles (nCuO). The nCuO delivers a remarkable dechlorination rate constant of 3.92 × 10^-2 L min^-1 m^-2 for 2,4-dichlorophenol, much higher than that of the conventional zerovalent (bi)metals. The absorbed O₂ on the nCuO surface is exclusively responsible for O₂^•- generation, and its reactivity increases with the elevated OV content because of the enhanced orbital hybridization between the O p- and Cu d-orbitals. More importantly, the ubiquitous carbonate species firmly bound to the surface OVs block the formation of the secondary oxidative species via H₂O₂ activation, assuring the dominant role of the in situ generated O₂^•- for the selective HOC dehalogenation. The carbonate-deactivated OVs of the nCuO can be feasibly recovered via air annealing for sustainable dehalogenation. This work provides a new opportunity for selective O₂^•- generation via interfacial defect engineering for dehalogenation and other environmental applications.

Recent Advances in Dual-Atom Site Catalysts for Efficient Oxygen and Carbon Dioxide Electrocatalysis

Atomically dispersed metal catalysts have been widely used in electrocatalysis because of their outstanding catalytic activity and high atomic utilization efficiency. As an extension of single-atom catalysts (SACs), dual-atom catalysts (DACs) provide new insights for the development of atomic-scale catalysts. Higher metal loading and more flexible active sites endow DACs with improved catalytic performance as well as optimized reaction mechanism model. In this review, DACs are firstly classified according to their configurations and metal sites. Subsequently, the synthetic strategies and characterization techniques of DACs are introduced. Furthermore, the applications of DACs are exemplified in various electrocatalytic reactions, including oxygen reduction reaction, oxygen evolution reaction and carbon dioxide reduction reaction. Finally, the prospects to be expected and challenges to be faced with are discussed.

Directing Charge Transfer in a Chemical-Bonded BaTiO3 @ReS2 Schottky Heterojunction for Piezoelectric Enhanced Photocatalysis

The piezo-assisted photocatalysis system, which can utilize solar energy and mechanical energy simulteneously, is promising but still challenging in the environmental remediation field. In this work, a novel metal-semiconductor BaTiO₃ @ReS₂ Schottky heterostructure is designed and it shows high-efficiency on piezo-assisted photocatalytic molecular oxygen activation. By combining experiment and calculation results, the distorted metal-phase ReS₂ nanosheets are found to be closely anchored on the surface of the BaTiO₃ nanorods, through interfacial ReO covalent bonds. The Schottky heterostructure not only forms electron-transfer channels but also exhibits enhanced oxygen activation capacity, which are helpful to produce more superoxide radicals. The polarization field induced by the piezoelectric BaTiO₃ can lower the Schottky barrier and thus reduce the transfer resistance of photogenerated electrons directing to the ReS₂ . As a result of the synergy effect between the two components, the BaTiO₃ @ReS₂ exhibits untrahigh activity for degradation of pollutants with an apparent rate constant of 0.133 min^-1 for piezo-assisted photocatalysis, which is 16.6 and 2.44 times as that of piezocatalysis and photocatalysis, respectively. This performance is higher than most reported BaTiO₃ -based piezo-assisted photocatalysis systems. This work paves the way for the design of high-efficiency piezo-assisted photocatalytic materials for environmental remediation through using green energies in nature.

Single-atom Ir1 supported on rutile TiO2 for excellent selective catalytic oxidation of ammonia

Gaseous ammonia (NH₃) in the atmosphere is potentially harmful to both human health and the environment. The selective catalytic oxidation of NH₃ (termed as NH₃-SCO) into N₂ and H₂O is a promising method for decreasing NH₃ emissions. A highly efficient catalyst is required for controlling NH₃ emissions by this method in practice. In this study, we prepared Ir/TiO₂ catalysts using different crystal structures of TiO₂ (rutile, P25 or anatase) as supports by a simple impregnation method and evaluated their performance in the NH₃-SCO. We found that the Ir/TiO₂-R (rutile) catalyst performed better than the Ir/TiO₂-P25 (mixed-phase) and Ir/TiO₂-A (anatase) catalyst. High-angle annular dark-field images of the aberration-corrected scanning transmission electron microscopy revealed that the Ir species were mainly atomically dispersed on the TiO₂ support in Ir/TiO₂-R with 1 wt% Ir loading, whereas the Ir species agglomerated to form clusters or nanoparticles in Ir/TiO₂-P25 and Ir/TiO₂-A. The combined results of X-ray absorption fine structure, H₂-temperature-programmed reduction, and in situ diffuse reflectance for infrared Fourier Transform spectroscopy studies suggested that atomically dispersed Ir species had stronger electronic metal-support interaction with rutile TiO₂, which resulted in easier to adsorb and activate O₂ at the interface and thus, better low-temperature activity of the Ir/TiO₂-R catalyst.

Adatom Bonding Sites in a Nickel-Fe3 O4 (001) Single-Atom Model Catalyst and O2 Reactivity Unveiled by Surface Action Spectroscopy with Infrared Free-Electron Laser Light

Single-atom (SA) catalysis presently receives much attention with its promise to decrease the cost of the active material while increasing the catalyst's performance. However, key details such as the exact location of SA species and their stability are often unclear due to a lack of atomic level information. Here, we show how vibrational spectra measured with surface action spectroscopy (SAS) and density functional theory (DFT) simulations can differentiate between different adatom binding sites and determine the location of Ni and Au single atoms on Fe₃ O₄ (001). We reveal that Ni and Au adatoms selectively bind to surface oxygen ions which are octahedrally coordinated to Fe ions. In addition, we find that the Ni adatoms can activate O₂ to superoxide in contrast to the bare surface and Ni in subsurface positions. Overall, we unveil the advantages of combining SAS and DFT for improving the understanding of single-atom catalysts.

Large-Scale Synthesis of Spinel Nix Mn3-x O4 Solid Solution Immobilized with Iridium Single Atoms for Efficient Alkaline Seawater Electrolysis

Seawater electrolysis not only affords a promising approach to produce clean hydrogen fuel but also alleviates the bottleneck of freshwater feeds. Here, a novel strategy for large-scale preparing spinel Ni_x Mn_3-x O₄ solid solution immobilized with iridium single-atoms (Ir-SAs) is developed by the sol-gel method. Benefitting from the surface-exposed Ir-SAs, Ir₁ /Ni_1.6 Mn_1.4 O₄ reveals boosted oxygen evolution reaction (OER) performance, achieving overpotentials of 330 and 350 mV at current densities of 100 and 200 mA cm^-2 in alkaline seawater. Moreover, only a cell voltage of 1.50 V is required to reach 500 mA cm^-2 with assembled Ir₁ /Ni_1.6 Mn_1.4 O₄ ‖Pt/C electrode pair under the industrial operating condition. The experimental characterizations and theoretical calculations highlight the effect of Ir-SAs on improving the intrinsic OER activity and facilitating surface charge transfer kinetics, and evidence the energetically stabilized *OOH and the destabilized chloride ion adsorption in Ir₁ /Ni_1.6 Mn_1.4 O₄ . This work demonstrates an effective method to produce efficient alkaline seawater electrocatalyst massively.

Metal-metal interactions in correlated single-atom catalysts

Single-atom catalysts (SACs) include a promising family of electrocatalysts with unique geometric structures. Beyond conventional ones with fully isolated metal sites, an emerging class of catalysts with the adjacent metal single atoms exhibiting intersite metal-metal interactions appear in recent years and can be denoted as correlated SACs (C-SACs). This type of catalysts provides more opportunities to achieve substantial structural modification and performance enhancement toward a wider range of electrocatalytic applications. On the basis of a clear identification of metal-metal interactions, this review critically examines the recent research progress in C-SACs. It shows that the control of metal-metal interactions enables regulation of atomic structure, local coordination, and electronic properties of metal single atoms, which facilitate the modulation of electrocatalytic behavior of C-SACs. Last, we outline directions for future work in the design and development of C-SACs, which is indispensable for creating high-performing new SAC architectures.