Hygroscopic holey graphene aerogel fibers enable highly efficient moisture capture, heat allocation and microwave absorption

Carbon nanofiber coated ionic crystal architecture withconfinement effect for high-performance microwave absorption along with high-efficiency water harvesting from air

Water is considered an effective microwave absorber due to its high transmittance and frequency-dispersive dielectric constant, yet it is challenging to form it into a stable state as an absorber. Herein, we developed a water-containing microwave absorber using chemical vapor deposition (CVD), namely, the bifunctional carbon/NaCl multi-interfaces hybrid with excellent water harvesting and microwave absorption performance. Carbon/NaCl exhibits remarkable water harvesting abilities from air, exceeding 210 % of its weight in 12 h. The development of the hydrophilic/hydrophobic heterojunction interface is responsible for this outstanding performance. Additionally, the interfacial polarization provided by carbon/NaCl, along with the dipole polarization induced by the internally captured water and defects, enhances its microwave absorption. The carbon/NaCl hybrid achieved a minimum reflection loss (RLmin) of -69.62 dB at 17.1 GHz with a thickness of 2.13 mm, and a maximum effective absorption bandwidth (EABmax) of 6.74 GHz at a thickness of 2.5 mm. Compared with raw NaCl (RLmin of -24.5 dB, EABmax of 3.88 GHz), the RLmin and EABmax values of the absorber increased by approximately 2.85 and 1.74 times. These results highlight the potential for bifunctional carbon/NaCl hybrid in applications within extreme environments, presenting a promising avenue for further research and development.

Prototype Alarm Integrating Pulse-Driven Nitrogen Dioxide Sensor Based on Holey Graphene Oxide/In2O3

NO2 seriously threatens human health and the ecological environment. However, the fabrication of highly sensitive NO2 sensors with rapid response/recovery rates, low detection limits, and ease of integration remains a challenge. Herein, benefiting from the fast carrier transfer and rich active sites, holey graphene oxide (HGO) was adopted to functionalize the In2O3 nanosheet to construct NO2 gas sensors. Characterization and theoretical calculations established the merits of HGO decoration in the NO2 sensing. The optimal sample, 0.5 wt % HGO/In2O3-sheet, exhibited superior sensing properties, resulting in a 1.37-fold improvement in response to 1 ppm of NO2 compared to the GO/In2O3 counterpart. Gas-sensing kinetics analysis revealed its lower activation energy and higher kinetic rate constants. Importantly, pulsed-temperature modulation was employed to decouple the gas adsorption from surface activation processes, achieving an ultrahigh response of 2776 to 1 ppm of NO2 for the 0.5 wt % HGO/In2O3-sheet sensor. Compared to the isothermal mode, this strategy enhanced the response value by 1.6 times, reduced the response/recovery time by 33%/70%, and enabled the detection of NO2 concentrations as low as 1 ppb. Finally, an NO2 monitoring alarm system based on the 0.5 wt % HGO/In2O3-sheet sensor with pulsed-temperature modulation was demonstrated for hazard warnings.

Functional Carbon Springs Enabled Dynamic Tunable Microwave Absorption and Thermal Insulation

Electromagnetic (EM) wave pollution and thermal damage pose serious hazards to delicate instruments. Functional aerogels offer a promising solution by mitigating EM interference and isolating heat. However, most of these materials struggle to balance thermal protection with microwave absorption (MA) efficiency due to a previously unidentified conflict between the optimizing strategies of the two properties. Herein, this study reports a solution involving the design of a carbon-based aerogel called functional carbon spring (FCS). Its unique long-range lamellar multi-arch microstructure enables tunable MA performance and excellent thermal insulation capability. Adjusting compression strain from 0% to 50%, the adjustable effective absorption bandwidth (EAB) spans up to 13.4 GHz, covering 84% of the measured frequency spectrum. Notably, at 75% strain, the EAB drops to 0 GHz, demonstrating a novel "on-off" switchability for MA performance. Its ultralow vertical thermal conductivity (12.7 mW m-1 K-1) and unique anisotropic heat transfer mechanism endow FCS with superior thermal protection effectiveness. Numerical simulations demonstrate that FCS outperforms common honeycomb structures and isotropic porous aerogels in thermal management. Furthermore, an "electromagnetic-thermal" dual-protection material database is established, which intuitively demonstrates the superiority of the solution. This work contributes to the advancement of multifunctional MA materials with significant potential for practical applications.

Engineering Hygroscopic MOF-Based Silk Via Bioinspired Interfacial Assembly for Fast Moisture Manipulation

Metal-organic frameworks (MOFs) have emerged as exceptional moisture sorbents in low humidity conditions. However, their typical powdered form often results in agglomeration, impeding water diffusion kinetics and practical handling. To enhance the accessibility and diversify the integration of MOFs, a universal and scalable bionic interfacial assembly method is introduced for fabricating MOF-based silk. The resulting silk, enriched with a high content of MOF-303, demonstrates a significant water adsorption capacity of 315.1 mg g-1 at 25% relative humidity, exhibiting a three fold faster water absorption compared with that of stacked MOFs powder on a gram-scale. Furthermore, it achieves efficient water release, with a rate of 8.1 mg g-1 min-1 under sunlight after surface photothermal modification. Through one-step drawing assembly, electrothermal wires can be incorporated into MOF-based silk and demonstrate fast and reversible moisture adsorption/desorption for indoor humidity control. It is envisioned that this assembling method and integrated functional silk will yield valuable insights into the rational engineering of MOFs toward practical applications in moisture management, molecule absorption, etc.

Electrochemical Switching of Electromagnetism by Hierarchical Disorder Tailored Atomic Scale Polarization

High-frequency electronic response governs a broad spectrum of electromagnetic applications from radiation protection, and signal compatibility, to energy recovery. Despite various efforts to manage electric conductivity, dynamic control over dielectric polarization for real-time electromagnetic modulation remains a notable challenge. Herein, an electrochemical lithiation-driven hierarchical disordering strategy is demonstrated for actively modulating electromagnetic properties. The controllable formation and diffusion of coherent interfaces and cation vacancies tailor the coupling of atomic electric field and thus the locally polarized domains, which leads to the reversible electromagnetic transparency/absorption switching with a tunable range of -0.8--20.4 dB for the reflection loss and a broad operation bandwidth of 4.6 GHz. Compared to traditional methods of heteroatomic doping, hydrogenation, mechanical deformation, and phase transition, the electrochemical strategy shows a larger regulation scope of dielectric permittivity with the maximum increase ratios of 260% and 1950% for real and imaginary parts, respectively. This enables the construction of various device architectures including the adaptive window and pixelated metasurface. The results offer opportunities to achieve intelligent electromagnetic devices and pave an avenue to rejuvenate various electromagnetic functions of semiconductive oxides.

Discovery of Deactivation Phenomenon in NiCo2S4/NiS2 Electromagnetic Wave Absorbent and Its Reactivation Mechanism

Over the past century, extensive research has been carried out on various types of microwave absorption (MA) materials, primarily emphasizing mechanism, performance, and even toward smart device. However, the deactivation, a crucial concern for practical applications, has long been long-neglected. In this work, an in-depth exploration of the deactivation mechanism reveals a significant competition between metal and oxygen, leading to the replacement of the S-M (M = Ni and Co) bond by a new S─O bond on the surface of absorber. This substitution initiates a series of collapse effect that introduces additional defective sites and diminishes the potential for charge transport. Subsequently, passive and active anti-deactivation strategies are developed to target the deactivation. The passive strategy involved intentionally creating electron-deficient structures at the initial Ni and Co sites in the crystal through the Fe doping engineering, with the objective of preventing the generation of S─O bonds. Furthermore, the active anti-deactivation strategy allows for the precise control of absorber deactivation and reactivation by employing accelerated thermodynamic and kinetic methods, enabling a reversible transformation of S-M through competitive reactions with S─O bonds. Finally, a fast deactivation and reactivation method is first proposed promising to stimulate further innovations and breakthroughs in practical applications.

Gas-Blows-Liquid Spinning Strategy Toward Mechanically Strong, Thermally Protective, Efficiently Hemostatic Aerogel Fibers/Fabrics

Nanoporous aerogel fibers enjoy the luxury of being one of the most attractive nanomaterials. However, the representative fabrication pathways have faced up with low production rates due to significant speed mismatch between slow sol-gel transition and as fast as possible spinning in the same period. Herein, a novel gas-blows-liquid spinning (GS) strategy with a spinning speed of 300-700 m s-1 is developed to get the high-speed and high-efficiency production of aerogel fibers/fabrics. The spinning speed of the GS strategy is 900 times higher than various techniques reported for aerogel fibers. The resulting aerogel fibers exhibit a high specific surface area (180 m2 g-1). In comparison, the aerogel fiber possesses the highest tensile strength (58.7±3.9 MPa) among its counterparts and aerogel fabric with surprising water-absorption and microparticle-blocking performances exhibits the application prospect for better hemostasis than that of commercial gauze and cotton ball. Besides, the GS aerogel fabrics with hierarchical aligned structures show better thermal insulation (≈0.035 Wm-1K-1) than wet spinning aerogel fabric and commercial insulation felts. This work has provided inspiration for fast fabricating more aerogel fibers/fabrics with this GS strategy, and the resulting aerogel fibers/fabrics may find significant application in the fields of 5G smart phones, wound hemostasis, etc.

Sodium alginate-based coaxial fibers synergistically integrate moisture actuation, length tracing, humidity sensing, and electric heating

The development of wearable electronics has driven the need for smart fibers with advanced multifunctional synergy. In this paper, we present a design of a multifunctional coaxial fiber that is composed of a biopolymer-derived core and an MXene/silver nanowire (AgNW) sheath by wet spinning. The fiber synergistically integrates moisture actuation, length tracing, humidity sensing, and electric heating, making it highly promising for portable devices and protective systems. The biopolymer-derived core provides deformation for moisture-sensitive actuation, while the MXene/AgNW sheath with good conductivity enables the fiber to perform electric heating, humidity sensing, and self-sensing actuation. The coaxial fiber can be programmed to rapidly desorb water molecules to shrink to its original length by using the MXene/AgNW sheath as an electrical heater. We demonstrate proof-of-concept applications based on the multifunctional fibers for thermal physiotherapy and wound healing/monitoring. The sodium alginate@MXene-based coaxial fiber presents a promising solution for the next-generation of smart wearable electronics.

Advancements and Challenges in Organic-Inorganic Composite Solid Electrolytes for All-Solid-State Lithium Batteries

To address the limitations of contemporary lithium-ion batteries, particularly their low energy density and safety concerns, all-solid-state lithium batteries equipped with solid-state electrolytes have been identified as an up-and-coming alternative. Among the various SEs, organic-inorganic composite solid electrolytes (OICSEs) that combine the advantages of both polymer and inorganic materials demonstrate promising potential for large-scale applications. However, OICSEs still face many challenges in practical applications, such as low ionic conductivity and poor interfacial stability, which severely limit their applications. This review provides a comprehensive overview of recent research advancements in OICSEs. Specifically, the influence of inorganic fillers on the main functional parameters of OICSEs, including ionic conductivity, Li+ transfer number, mechanical strength, electrochemical stability, electronic conductivity, and thermal stability are systematically discussed. The lithium-ion conduction mechanism of OICSE is thoroughly analyzed and concluded from the microscopic perspective. Besides, the classic inorganic filler types, including both inert and active fillers, are categorized with special emphasis on the relationship between inorganic filler structure design and the electrochemical performance of OICSEs. Finally, the advanced characterization techniques relevant to OICSEs are summarized, and the challenges and perspectives on the future development of OICSEs are also highlighted for constructing superior ASSLBs.

Customized Pore Creation Strategies for Hyperelastic, Robust, Insulating Multifunctional MXene Aerogels for Microwave Absorption

The construction of heterogeneous microstructure and the selection of multicomponents have turned into a research hotspot in developing ultralight, multifunctional, high-efficiency electromagnetic wave absorbing (EMA) materials. Although aerogels are promising materials to fulfill the above requirements, the increase in functional fillers inevitably leads to the deterioration of intrinsic properties. Tuning the electromagnetic properties from the structural design point of view remains a difficult challenge. Herein, we design customized pore creation strategies via introducing sacrificial templates to optimize the conductive path and construct the discontinuous dielectric medium, increasing dielectric loss and achieving efficient microwave absorption properties. A 3D porous composite (MEM) was crafted, which encapsulated an EVA/FeCoNi (EVA/MNPs) framework with Ti3C2Tx MXene coating by employing a direct heated cross-linking and immersion method. Controllable adjustment of the conductive network inside the porous structure and regulation of the dielectric character are achieved by porosity variation. Eventually, the MEM-5 with a porosity of 66.67% realizes RLmin of -39.2 dB (2.2 mm) and can cover the entire X band. Moreover, through off-axis electronic holography and the calculation of conduction loss and polarization loss, the dielectric property is deeply investigated, and the inner mechanism of optimization is pointed out. Thanks to the inherent characteristic of EVA and the porous structure, MEM-5 showed excellent thermal insulating and superior compressibility, which can maintain 60 °C on a 90-100 °C continuous heating stage and reached a maximum compressive strength of 60.12 kPa at 50% strain. Conceivably, this work provides a facile method for the fabrication of highly efficient microwave absorbers applied under complex conditions.

Construction of 3D Fibonacci Cauliflower-Like NiCo2S4/Expanded Graphite Heterogeneous Structures for Enhanced Electromagnetic Wave Absorption

Highly efficient electromagnetic wave (EMW)-absorbing multicomposites can be fabricated by constructing particular structures using suitable components. Expanded graphite (EG) has a 3D, low-density porous structure; however, it suffers from poor impedance matching and EMW absorption properties. Based on this information, in the present study, NiCo2S4 components with different morphologies are successfully loaded onto a 3D EG surface using a facile microwave solvothermal method to achieve a synergistic effect between the different components. The NiCo2S4 content is adjusted to alter the compositional morphology and electromagnetic parameters of the composites to achieve impedance-matching and obtain excellent EMW absorption properties. The heterogeneous interface between EG and NiCo2S4 induces an inhomogeneous spatial charge distribution and enhances interfacial polarization. The defects in the material and oxygen-containing groups induce dipole polarization, which enhances the polarization-relaxation process of the composites. The 3D porous heterostructure of the "Fibonacci cauliflower"-shaped NiCo2S4/EG composites results in an optimal reflection loss of -64.93 dB at a filler rate of only 14 wt.%. Analysis of the synergistic conduction loss and polarization loss mechanisms in carbon-based materials with heterogeneous interfaces has led to the development of excellent EMW absorption materials.

Enhanced continuous atmospheric water harvesting with scalable hygroscopic gel driven by natural sunlight and wind

Sorption-based atmospheric water harvesting (SAWH) has received unprecedented attention as a future water and energy platform. However, the water productivity of SAWH systems is still constrained by the slow sorption kinetics at material and component levels and inefficient condensation. Here, we report a facile method to prepare hygroscopic interconnected porous gel (HIPG) with fast sorption-desorption kinetics, high scalability and stability, and strong adhesion property for highly efficient SAWH. We further design a solar-wind coupling driven SAWH device with collaborative heat and mass enhancement achieving continuous water production. Concentrated sunlight contributes to enhancing the desorption and condensation synergistically, and natural wind is introduced to drive the device operation and improve the sorption kinetics. The device demonstrated record high working performance of 14.9 Lwater m-2 day-1 and thermal efficiency of 25.7% in indoor experiments and 3.5-8.9 Lwater m-2 day-1 in outdoor experiments by solar concentration without any other energy consumption. This work provides an up-and-coming pathway to realize highly efficient and sustainable clean water supply for off-grid and arid regions.

A Super-Hygroscopic Solar-Regenerated Alginate-Based Composite for Atmospheric Water Harvesting

Global water scarcity is leading to increasingly tense competition across populations. In order to complement the largely fast-depleting fresh water sources and mitigate the challenges generated by brine discharge from desalination, atmospheric water harvesting (AWH) has emerged to support long-term water supply. This work presents a novel alginate-based hybrid material comprised of porous silico-aluminophosphate-34 (SAPO-34) as fast-transport channel medium as well as hydrophilicity and stability enhancer, and graphene-based sheets as light absorber for solar-enabled evaporation, both optimally incorporated in an alginate matrix, resulting in a composite sorbent capable of harvesting water from the atmosphere with a record intake of up to 6.85 gw gs -1. Natural sunlight is solely used to enable desorption achieving increase of the temperature of the developed network up to 60 °C and resulting in release of the sorbed water, with impurities content well below the World Health Organization (WHO) upper limits. After 30 cycles of sorption and desorption, the composite hydrogel displayed unchanged water uptake and stability. This work provides an impactful perspective toward sustainable generation of water from humidity without external energy consumption supporting the emergence of alternative water production solutions.

In situ Electrical Impedance Tomography for Visualizing Water Transportation in Hygroscopic Aerogels

The global water crisis demands immediate attention, and atmospheric water harvesting (AWH) provides a viable alternative. However, studying the real-time subtle relationship between water absorption, diffusion, and internal structure for hygroscopic materials is challenging. Herein, a dynamic visualization technique is proposed that utilizes an in situ electrical impedance tomography (EIT) system and a precise reconstruction algorithm to achieve real-time monitoring of the water sorption process within aerogels from an internal microstructural perspective. These results can be inferred that composites' pore sizes affecting the kinetics of their moisture absorption. In addition, the diffusion path of moisture absorption and the distribution of stored moisture inside aerogels exhibit intrinsic self-selective behavior, where the fiber skeleton of the aerogel plays a crucial role. In summary, this work proposes a generic EIT-based technique for the in situ and dynamic monitoring of the hygroscopic process, pointing to an entirely new approach regarding research on AWH materials.

Aerogel-Involved Triple-State Gels Resemble Natural Living Leaves in Structure and Multi-Functions

Natural plant leaves with multiple functions, for example, spectral features, transpiration, photosynthesis, etc., have played a significant role in the ecosystem, and artificial synthesis of plant leaves with multiple functions of natural ones is still a great challenge. Herein, this work presents an aerogel-involved living leaf (AL), most similar to natural ones so far, by embedding super-hydrophobic SiO2 aerogel microparticles in polyvinyl alcohol hydrogel in the presence of hygroscopic salt and chlorophyllin copper sodium to form solid-liquid-vapor triple-state gel. The AL shows a high spectral similarity with all sampled 15 species of natural leaves and exhibits ≈4-7 times transpiration speed higher than natural leaves. More importantly, AL can achieve several times higher photosynthesis than natural leaves without the energy provided by the respiratory action of natural ones. This work demonstrates the feasibility of creating ALs with natural leaf-like triple-state gel structures and multiple functions, opening up new avenues for energy conversion, environmental engineering, and biomimetic applications.

Topological Polymer Networks-Enabled Mechanically Strong Polyamide-Imide Aerogel Fibers for Thermal Insulation in Harsh Environments

Aerogel fibers have sparked substantial interest as attractive candidates for thermal insulation materials. Developing aerogel fibers with the desired porous structure, good knittability, flame retardancy, and high- and low-temperature resistance is of great significance for practical applications; however, that is very challenging, especially by using an efficient method. Herein, mechanically strong and flexible aerogel fibers with remarkable thermal insulation performance are reported, which are achieved by constructing stiff-soft topological polymer networks and a multilevel hollow porous structure. The combination of polyamide-imide (PAI) with stiff chains and polyurethane (PU) with soft chains is first found to be able to form a topological entanglement architecture. More importantly, multilevel hollow pores can be constructed synchronously through just a one-step and green wet-spinning process. The resultant PAI/PU@340 aerogel fibers show an ultrahigh breaking strength of 94.5 MPa and superelastic property with a breaking strain of 20%. Furthermore, they can be knitted into fabrics with a low thermal conductivity of 25 mW/(m·K) and exhibit attractive thermal insulation property under extremely high (300 °C) and low temperatures (-191 °C), implying them as promising candidates for next-generation thermal insulation materials.

Ultrathin aerogel-structured micro/nanofiber metafabric via dual air-gelation synthesis for self-sustainable heating

Incorporating passive heating structures into personal thermal management technologies could effectively mitigate the escalating energy crisis. However, current passive heating materials struggle to balance thickness and insulating capability, resulting in compromised comfort, space efficiency, and limited thermoregulatory performance. Here, a dual air-gelation strategy, is developed to directly synthesize ultrathin and self-sustainable heating metafabric with 3D dual-network structure during electrospinning. Controlling the interactions among polymer, solvent, and water enables the microphase separation of charged jets, while adjusting the distribution of carbon black nanoparticles within charged fluids to form fibrous networks composed of interlaced aerogel micro/nanofibers with heat storage capabilities. With a low thickness of 0.18 mm, the integrated metafabric exhibits exceptional thermal insulation performance (15.8 mW m-1K-1), superhydrophobicity, enhanced mechanical properties, and high breathability while maintaining self-sustainable radiative heating ability (long-lasting warming of 8.8 °C). This strategy provides rich possibilities to develop advanced fibrous materials for smart textiles and thermal management.

Chemistries and materials for atmospheric water harvesting

Atmospheric water harvesting (AWH) is recognized as a crucial strategy to address the global challenge of water scarcity by tapping into the vast reserves of atmospheric moisture for potable water supply. Within this domain, sorbents lie in the core of AWH technologies as they possess broad adaptability across a wide spectrum of humidity levels, underpinned by the cyclic sorption and desorption processes of sorbents, necessitating a multi-scale viewpoint regarding the rational material and chemical selection and design. This Invited Review delves into the essential sorption mechanisms observed across various classes of sorbent systems, emphasizing the water-sorbent interactions and the progression of water networks. A special focus is placed on the insights derived from isotherm profiles, which elucidate sorbent structures and sorption dynamics. From these foundational principles, we derive material and chemical design guidelines and identify key tuning factors from a structural-functional perspective across multiple material systems, addressing their fundamental chemistries and unique attributes. The review further navigates through system-level design considerations to optimize water production efficiency. This review aims to equip researchers in the field of AWH with a thorough understanding of the water-sorbent interactions, material design principles, and system-level considerations essential for advancing this technology.

Hygroscopic Mg-Al LDHs composite microspheres for highly efficient hyperspectral camouflage in the VIS and NIR wavebands

In order to enhance the hyperspectral camouflage efficacy of stealth coatings against a natural vegetative backdrop, LiCl, known for its significant hygroscopic properties, was incorporated into green Mg-Al layered double hydroxide (Mg-Al LDHs) material. Micron-sized composite microspheres were subsequently synthesized via the spray-drying granulation technique. The structure, morphology, and chemical composition of these microspheres were thoroughly characterized by X-ray diffraction, scanning electron microscopy, laser particle size analysis, nitrogen adsorption-desorption isotherms, and Fourier-transform infrared spectroscopy. The effect of LiCl content on the moisture absorption capacity and near-infrared reflectance spectra of the microspheres was systematically evaluated. We found that incorporating an optimal amount of LiCl into the internal pores of the Mg-Al LDHs microspheres did not compromise their smooth surface morphology and uniform particulate distribution. Notably, when the LiCl content was 10%, the maximum saturation moisture uptake ratio of the coating increased to 0.75 g/g. This hygroscopicity significantly enhanced the absorption and scattering of near-infrared radiation by the coating while concurrently improving its ability to modulate the shape and reflectance of both the visible and near-infrared spectral curves. Spectral congruence between the synthetic coating and natural green foliage was quantified at 97.41%. Moreover, this performance was maintained over 10 cycles of programmed drying and re-humidification, and the coating consistently demonstrated stable hygroscopic properties and sustained over 95% spectral congruence. These optimized artificial coatings were found to effectively confuse hyperspectral classification algorithms, thus blending seamlessly into a natural foliage backdrop. This study provides a new method for regulating VIS and NIR spectral (visible-near infrared spectrum) features, which will be critical for applications in advanced hyperspectral camouflage materials.

Wireless Powered Microwave-Light Conversion Platform with Dual-Stimulus Nanoresponder Coating for Deep-Seated Photodynamic Therapy

Traditional external field-assisted therapies, e.g., microwave (MW) therapy and phototherapy, cannot effectively and minimally damage eliminate deep-seated infection, owing to the poor penetrability of light and low reactive oxygen species (ROS) stimulation capability of MW. Herein, an implantable and wireless-powered therapeutic platform (CNT-FeTHQ-TS), in which external MW can be converted into internal light via MW wireless-powered light-emitting chips, is designed to eradicate deep-seated tissue infections by MW-induced deep-seated photodynamic therapy. In application, CNT-FeTHQ-TS is implanted at internal lesions, and the chip emits light under external MW irradiation. Subsequently, CNT-FeTHQ coating in the platform can respond to both MW and light simultaneously to generate ROS and MW-hyperthermia for rapid and precise sterilization at focus. Importantly, MW also improves the photodynamic performance of CNT-FeTHQ by introducing vacancies in FeTHQ to facilitate the photoexcitation process and changing the spin state of electrons to inhibit the complexation of photogenerated electron-hole pairs, which were confirmed by simulation calculations and in situ MW-irradiated photoluminescence experiments. In vivo, CNT-FeTHQ-TS can effectively cure mice with Staphylococcus aureus infection in dorsal subcutaneous tissue. This work overcomes the key clinical limitations of safe energy transmission and conversion for treating deep-seated infections.

Entangled Mesh Hydrogels with Macroporous Topologies via Cryogelation for Rapid Atmospheric Water Harvesting

Sorption-based atmospheric water harvesting (SAWH) is a promising technology to alleviate freshwater scarcity. Recently, hygroscopic salt-hydrogel composites (HSHCs) have emerged as attractive candidates with their high water uptake, versatile designability, and scale-up fabrication. However, achieving high-performance SAWH applications for HSHCs has been challenging because of their sluggish kinetics, attributed to their limited mass transport properties. Herein, a universal network engineering of hydrogels using a cryogelation method is presented, significantly improving the SAWH kinetics of HSHCs. As a result of the entangled mesh confinements formed during cryogelation, a stable macroporous topology is attained and maintained within the obtained entangled-mesh hydrogels (EMHs), leading to significantly enhanced mass transport properties compared to conventional dense hydrogels (CDHs). With it, corresponding hygroscopic EMHs (HEMHs) simultaneously exhibit faster moisture sorption and solar-driven water desorption. Consequently, a rapid-cycling HEMHs-based harvester delivers a practical freshwater production of 2.85 Lwater kgsorbents -1 day-1 via continuous eight sorption/desorption cycles, outperforming other state-of-the-art hydrogel-based sorbents. Significantly, the generalizability of this strategy is validated by extending it to other hydrogels used in HSHCs. Overall, this work offers a new approach to efficiently address long-standing challenges of sluggish kinetics in current HSHCs, promoting them toward the next-generation SAWH applications.

Intelligent Tunable Wave-Absorbing CNTs/VO2/ANF Composite Aerogels Based on Temperature-Driving

The development of new electromagnetic absorbing materials is the main strategy to address electromagnetic radiation. Once traditional electromagnetic wave-absorbing materials are prepared, it is difficult to dynamically change their electromagnetic wave-absorbing performance. Facing the complexity of the information age and the rapid development of modern radar, it is significant to develop intelligent modulation of electromagnetic wave-absorbing materials. Here, CNTs/VO2/ANF composite aerogels with dynamic frequency tunability and switchable absorption on/off were synthesized. Based on the phase change behavior of VO2, the degree of polarization and interfacial effects of multiple heterogeneous interfaces between VO2 and CNTs and aramid nanofibers (ANFs) were modulated at different temperatures. With the increase in temperature (from 25 to 200 °C), the maximum absorption frequency of the frequency tunable aerogel is modulated from 12.24 to 8.56 GHz in the X-band, and the absorption intensity remains stable. The maximum effective switching bandwidth (ΔEAB) of the wave-absorbing switchable aerogel is 3.70 GHz. This study provides insights into intelligent electromagnetic wave absorption performance and paves the way for temperature-driven application of intelligent modulation of electromagnetic absorbers.

Constructing Built-In Electric Fields with Semiconductor Junctions and Schottky Junctions Based on Mo-MXene/Mo-Metal Sulfides for Electromagnetic Response

The exploration of novel multivariate heterostructures has emerged as a pivotal strategy for developing high-performance electromagnetic wave (EMW) absorption materials. However, the loss mechanism in traditional heterostructures is relatively simple, guided by empirical observations, and is not monotonous. In this work, we presented a novel semiconductor-semiconductor-metal heterostructure system, Mo-MXene/Mo-metal sulfides (metal = Sn, Fe, Mn, Co, Ni, Zn, and Cu), including semiconductor junctions and Mott-Schottky junctions. By skillfully combining these distinct functional components (Mo-MXene, MoS2, metal sulfides), we can engineer a multiple heterogeneous interface with superior absorption capabilities, broad effective absorption bandwidths, and ultrathin matching thickness. The successful establishment of semiconductor-semiconductor-metal heterostructures gives rise to a built-in electric field that intensifies electron transfer, as confirmed by density functional theory, which collaborates with multiple dielectric polarization mechanisms to substantially amplify EMW absorption. We detailed a successful synthesis of a series of Mo-MXene/Mo-metal sulfides featuring both semiconductor-semiconductor and semiconductor-metal interfaces. The achievements were most pronounced in Mo-MXene/Mo-Sn sulfide, which achieved remarkable reflection loss values of - 70.6 dB at a matching thickness of only 1.885 mm. Radar cross-section calculations indicate that these MXene/Mo-metal sulfides have tremendous potential in practical military stealth technology. This work marks a departure from conventional component design limitations and presents a novel pathway for the creation of advanced MXene-based composites with potent EMW absorption capabilities.

Enhancing Low-Frequency Microwave Absorption Through Structural Polarization Modulation of MXenes

Two-dimensional carbon-based materials have shown promising electromagnetic wave absorption capabilities in mid- and high-frequency ranges, but face challenges in low-frequency absorption due to limited control over polarization response mechanisms and ambiguous resonance behavior. In this study, we propose a novel approach to enhance absorption efficiency in aligned three-dimensional (3D) MXene/CNF (cellulose nanofibers) cavities by modifying polarization properties and manipulating resonance response in the 3D MXene architecture. This controlled polarization mechanism results in a significant shift of the main absorption region from the X-band to the S-band, leading to a remarkable reflection loss value of - 47.9 dB in the low-frequency range. Furthermore, our findings revealed the importance of the oriented electromagnetic coupling in influencing electromagnetic response and microwave absorption properties. The present study inspired us to develop a generic strategy for low-frequency tuned absorption in the absence of magnetic element participation, while orientation-induced polarization and the derived magnetic resonance coupling are the key controlling factors of the method.

Preparation of Fibrous Three-Dimensional Porous Materials and Their Research Progress in the Field of Stealth Protection

Intelligent and diversified development of modern detection technology greatly affects the battlefield survivability of military targets, especially infrared, acoustic wave, and radar detection expose targets by capturing their unavoidable infrared radiation, acoustic wave, and electromagnetic wave information, greatly affecting their battlefield survival and penetration capabilities. Therefore, there is an urgent need to develop stealth-protective materials that can suppress infrared radiation, reduce acoustic characteristics, and weaken electromagnetic signals. Fibrous three-dimensional porous materials, with their high porosity, excellent structural adjustability, and superior mechanical properties, possess strong potential for development in the field of stealth protection. This article introduced and reviewed the characteristics and development process of fibrous three-dimensional porous materials at both the micrometer and nanometer scales. Then, the process and characteristics of preparing fibrous three-dimensional porous materials through vacuum forming, gel solidification, freeze-casting, and impregnation stacking methods were analyzed and discussed. Meanwhile, their current application status in infrared, acoustic wave, and radar stealth fields was summarized and their existing problems and development trends in these areas from the perspectives of preparation processes and applicability were analyzed. Finally, several prospects for the current challenges faced by fibrous three-dimensional porous materials were proposed as follows: functionally modifying fibers to enhance their applicability through self-cross-linking; establishing theoretical models for the transmission of thermal energy, acoustic waves, and electromagnetic waves within fibrous porous materials; constructing fibrous porous materials resistant to impact, shear, and fracture to meet the needs of practical applications; developing multifunctional stealth fibrous porous materials to confer full-spectrum broadband stealth capability; and exploring the relationship between material size and mechanical properties as a basis for preparing large-scale samples that meet the application's requirement. This review is very timely and aims to focus researchers' attention on the importance and research progress of fibrous porous materials in the field of stealth protection, so as to solve the problems and challenges of fibrous porous materials in the field of stealth protection and to promote the further innovation of fibrous porous materials in terms of structure and function.

Visible Microfluidic Deprotonation for Aramid Nanofibers as Building Blocks of Cascade-Microfluidic-Processed Colloidal Aerogels

 Microfluidic deprotonation approach is proposed to realize continuous, scalable, efficient, and uniform production of aramid nanofibers (ANFs) by virtue of large specific surface area, high mixing efficiency, strong heat transfer capacity, narrow residence time distribution, mild laminar-flow process, and amplification-free effect of the microchannel reactor. By means of monitoring capabilities endowed by the high transparency of the microchannel, the kinetic exfoliation process of original aramid particles is in situ observed and the corresponding exfoliation mechanism is established quantificationally. The deprotonated time can be reduced from the traditional several days to 7 min for the final colloidal dispersion due to the synergistic effect between enhanced local shearing/mixing and the rotational motion of aramid particles in microchannel revealed by numerical simulations. Furthermore, the cascade microfluidic processing approach is used to make various ANF colloidal aerogels including aerogel fibers, aerogel films, and 3D-printed aerogel articles. Comprehensive characterizations show that these cascade-microfluidic-processed colloidal aerogels have identical features as those prepared in batch-style mode, revealing the versatile use value of these ANFs. This work achieves significant progress toward continuous and efficient production of ANFs, bringing about appreciable prospects for the practical application of ANF-based materials and providing inspiration for exfoliating any other nano-building blocks.

MXene-Enabled Pneumatic Multiscale Shape Morphing for Adaptive, Programmable and Multimodal Radar-infrared Compatible Camouflage

Achieving radar-infrared compatible camouflage with dynamic adaptability has been a long-sought goal, but faces significant challenges owing to the limited dispersion relations of conventional material systems operating in different wavelength ranges. Here, this work proposes the concept of pneumatic multiscale shape morphing and design a periodically arranged pneumatic unit consisting of MXene-based morphable conductors and intake platforms. During gas actuation, the morphable conductor transforms centimeter-scale 2D flat sheets into 3D balloon shapes to enhance microwave absorption behavior, and also reconfigures micrometer-scale MXene wrinkles into smooth planes in combination with cavity-induced low heat transfer to minimize infrared (IR) signatures. Through theory-guided reverse engineering, the final pneumatic matrix shows remarkable frequency tunability (2.64-18.0 GHz), moderate IR emissivity regulation (0.14 at 7-16.5 µm), rapid responsiveness (≈30 ms), wide-angle operation (>45°), and excellent environmental tolerance. Additionally, the multiplexed pneumatic matrix enables over 14 programmable coding sequences that independently alter thermal radiation without compromising radar stealth, and allows multimodal camouflage switching between three distinct compatible states. The approach may facilitate the evolution of camouflage techniques and electromagnetic functional materials toward multispectral, adaptability and intelligence.

Visualizing Nanoscale Interlayer Magnetic Interactions and Unconventional Low-Frequency Behaviors in Ferromagnetic Multishelled Structures

Precise manipulation of van der Waals forces within 2D atomic layers allows for exact control over electron-phonon coupling, leading to the exceptional quantum properties. However, applying this technique to diverse structures such as 3D materials is challenging. Therefore, investigating new hierarchical structures and different interlayer forces is crucial for overcoming these limitations and discovering novel physical properties. In this work, a multishelled ferromagnetic material with controllable shell numbers is developed. By strategically regulating the magnetic interactions between these shells, the magnetic properties of each shell are fine-tuned. This approach reveals distinctive magnetic characteristics including regulated magnetic domain configurations and enhanced effective fields. The nanoscale magnetic interactions between the shells are observed and analyzed, which shed light on the modified magnetic properties of each shell, enhancing the understanding and control of ferromagnetic materials. The distinctive magnetic interaction significantly boosts electromagnetic absorption at low-frequency frequencies used by fifth-generation wireless devices, outperforming ferromagnetic materials without multilayer structures by several folds. The application of magnetic interactions in materials science reveals thrilling prospects for technological and electronic innovation.

Regulating the Electronic Structure of MAX Phases Based on Rare Earth Element Sc to Enhance Electromagnetic Wave Absorption

MAX phases are highly promising materials for electromagnetic (EM) wave absorption because of their specific combination of metal and ceramic properties, making them particularly suitable for harsh environments. However, their higher matching thickness and impedance mismatching can limit their ability to attenuate EM waves. To address this issue, researchers have focused on regulating the electronic structure of MAX phases through structural engineering. In this study, we successfully synthesized a ternary MAX phase known as Sc2GaC MAX with the rare earth element Sc incorporated into the M-site sublayer, resulting in exceptional conductivity and impressive stability at high temperatures. The Sc2GaC demonstrates a strong reflection loss (RL) of -47.7 dB (1.3 mm) and an effective absorption bandwidth (EAB) of 5.28 GHz. It also achieves effective absorption of EM wave energy across a wide frequency range, encompassing the X and Ku bands. This exceptional performance is observed within a thickness range of 1.3 to 2.1 mm, making it significantly superior to other Ga-MAX phases. Furthermore, Sc2GaC exhibited excellent absorption performance even at elevated temperatures. After undergoing oxidation at 800 °C, it achieves a minimum RL of -28.3 dB. Conversely, when treated at 1400 °C under an argon atmosphere, Sc2GaC demonstrates even higher performance, with a minimum RL of -46.1 dB. This study highlights the potential of structural engineering to modify the EM wave absorption performance of the MAX phase by controlling its intrinsic electronic structure.

Wearable Aerogels for Personal Thermal Management and Smart Devices

Extreme climates have become frequent nowadays, causing increased heat stress in human daily life. Personal thermal management (PTM), a technology that controls the human body's microenvironment, has become a promising strategy to address heat stress. While effective in ordinary environments, traditional high-performance fibers, such as ultrafine, porous, highly thermally conductive, and phase change materials, fall short when dealing with harsh conditions or large temperature fluctuations. Aerogels, a third-generation superinsulation material, have garnered extensive attention among researchers for their thermal management applications in building energy conservation, transportation, and aerospace, attributed to their extremely low densities and thermal conductivity. While aerogels have historically faced challenges related to weak mechanical strength and limited secondary processing capacity, recent advancements have witnessed notable progress in the development of wearable aerogels for PTM. This progress underscores their potential applications within extremely harsh environments, serving as self-powered smart devices and sensors. This Review offers a timely overview of wearable aerogels and their PTM applications with a particular focus on their wearability and suitability. Finally, the discussion classifies five types of PTM applications based on aerogel function: thermal insulation, heating, cooling, adaptive regulation (involving thermal insulation, heating, and cooling), and utilization of aerogels as wearable smart devices.

Microwave-Absorbing Foams with Adjustable Absorption Frequency and Structural Coloration

Microwave-absorbing materials with regulatable absorption frequency and optical camouflage hold great significance in intelligent electronic devices and advanced stealth technology. Herein, we present an innovative microwave-absorbing foam that can dynamically tune microwave absorption frequencies via a simple mechanical compression while in parallel enabling optical camouflage over broad spectral ranges by adjusting the structural colors. The vivid colors spanning different color categories generated from thin-film interference can be precisely regulated by adjusting the thickness of the conformal TiO2 coatings on Ni/melamine foam. Enhanced interfacial and defect-induced polarizations resulting from the introduction of TiO2 coating synergistically contribute to the dielectric attenuation performance. Consequently, such a foam exhibits exceptional microwave absorption capabilities, and the absorption frequency can be dynamically tuned from the S band to the Ku band by manipulating its compression ratio. Additionally, simulation calculations validate the adjustable electromagnetic wave loss behavior, offering valuable insights for the development of next-generation intelligent electromagnetic devices across diverse fields.

Atomic Valence Reversal-Induced Polarization Resonance Spurs Highly Efficient Electromagnetic Wave Absorption in α-Fe2O3@Carbon Microtubes

Variegation and complexity of polarization relaxation loss in many heterostructured materials provide available mechanisms to seek a strong electromagnetic wave (EMW) absorption performance. Here we construct a unique heterostructured compound that bonds α-Fe2O3 nanosheets of the (110) plane on carbon microtubes (CMTs). Through effective alignment between the Fermi energy level of CMTs and the conduction band position of α-Fe2O3 nanosheets at the interface, we attain substantial polarization relaxation loss via novel atomic valence reversal between Fe(III) ↔ Fe(III-) induced with periodic electron injection from conductive CMTs under EMW irradiation to give α-Fe2O3 nanosheets. Such heterostructured materials possess currently reported minimum reflection loss of -84.01 dB centered at 10.99 GHz at a thickness of 3.19 mm and an effective absorption bandwidth (reflection loss ≤ -10 dB) of 7.17 GHz (10.83-18 GHz) at 2.65 mm. This work provides an effective strategy for designing strong EMW absorbers by combining highly efficient electron injection and atomic valence reversal.

Biopolymers for Hygroscopic Material Development

The effective management of atmospheric water will create huge value for mankind. Diversified and sustainable biopolymers that are derived from organisms provide rich building blocks for various hygroscopic materials. Here, a comprehensive review of recent advances in developing biopolymers for hygroscopic materials is provided. It is begun with a brief introduction of species diversity and the processes of obtaining various biopolymer materials from organisms. The fabrication of hygroscopic materials is then illustrated, with a specific focus on the use of biopolymer-derived materials as substrates to produce composites and the use of biopolymers as building blocks to fabricate composite gels. Next, the representative applications of biopolymer-derived hygroscopic materials for dehumidification, atmospheric water harvesting, and power generation are systematically presented. An outlook on future challenges and key issues worthy of attention are finally provided.

Interfacial Assembly of 2D Graphene-Derived Ion Channels for Water-Based Green Energy Conversion

The utilization of sustained and green energy is believed to alleviate increasing menace of global environmental concerns and energy dilemma. Interfacial assembly of 2D graphene-derived ion channels (2D-GDICs) with tunable ion/fluid transport behavior enables efficient harvesting of renewable green energy from ubiquitous water, especially for osmotic energy harvesting. In this review, various interfacial assembly strategies for fabricating diverse 2D-GDICs are summarized and their ion transport properties are discussed. This review analyzes how particular structure and charge density/distribution of 2D-GDIC can be modulated to minimize internal resistance of ion/fluid transport and enhance energy conversion efficiency, and highlights stimuli-responsive functions and stability of 2D-GDIC and further examines the possibility of integrating 2D-GDIC with other energy conversion systems. Notably, the presented preparation and applications of 2D-GDIC also inspire and guide other 2D materials to fabricate sophisticated ion channels for targeted applications. Finally, potential challenges in this field is analyzed and a prospect to future developments toward high-performance or large-scale real-word applications is offered.

Pneumatic Structural Deformation to Enhance Resonance Behavior for Broadband and Adaptive Radar Stealth

Ideal radar absorbing materials (RAMs) require instantaneous, programmable, and spontaneous adaptability to cope with a complex electromagnetic (EM) environment across the full working frequency. Despite various material systems and adaptive mechanisms having been demonstrated, it remains a formidable challenge to integrate these benefits simultaneously. Here, we present a pneumatic matrix that couples morphable MXene/elastomer conductors with dielectric spacers, which leverages controllable airflow to reconfigure the spatial structure between a flat sheet and a hemispherical crown while maintaining resistance stability via wrinkle folding and unfolding. The interdimensional reconfigurations drastically induce multiple resonance behavior, enabling the matrix remarkable frequency tunability (144.5%), ultrawide bandwidth (15 GHz), weak angular dependence (45° incidence), ultrafast responsiveness (∼30 ms), and excellent reproducibility (1000 cycles). With multichannel fluidic and conceptual automated control systems, the final pneumatic device demonstrates a multiplexed, programmable, and autonomous transformable mode that builds a promising platform for smart radar cloaking.

Entropy engineering enhances the electromagnetic wave absorption of high-entropy transition metal dichalcogenides/N-doped carbon nanofiber composites

Entropy engineering strategies provide a broader platform for exploring the behavior of electromagnetic wave (EMW) absorption materials and their absorption mechanisms on the microscopic scale. In this work, a novel entropy engineering strategy was developed to improve the EMW absorption properties of MoS2. A hierarchical N-doped carbon nanofiber/MoS2 (NCNF/MS) composite was synthesized using the electrospinning and hydrothermal methods. Then, the conformational entropy of MoS2 was increased by sequentially integrating elements such as W, Se, and Te. Although MoS2 maintains a single 2H-phase structure throughout the entropy increase process, it triggers a series of complex changes at the microscopic level, including lattice distortion, ingenious electronic structure adjustments, and an increase in defect density. These changes provide more possibilities for the EMW interaction with the absorber, which significantly enhances the dielectric behavior of the composites, including conduction and polarization losses. Owing to the unique hierarchical structure and rich defect structure, the obtained entropy-increased NCNF/MWSST exhibits excellent EMW absorption performance. The minimum reflection loss reaches -60.7 dB, and the maximum effective absorption bandwidth is 6.48 GHz, which is improved by almost 584% and 810% compared to NCNF/MS. This study provides a new way to design efficient and high-performance MoS2-based absorbers and provides valuable insights for exploring the entropy-increasing strategies to optimize the EMW absorption properties.

Controllable proton-reservoir ordered gel towards reversible switching and reliable electromagnetic interference shielding

Smart and dynamic electromagnetic interference (EMI) shielding materials possess a remarkable capacity to modify their EMI shielding abilities, rendering them invaluable in various civil and military applications. However, the present response mechanism of switch-type EMI shielding materials is slightly restricted, as it primarily depends on continuous pressure induction, thereby resulting in concerns regarding their durability and reliability. Herein, for the first time, we demonstrate a novel method for achieving solvent-responsive, reversible switching, and robust EMI shielding capabilities using a controlled proton-reservoir ordered gel. The gel contains polyaniline (PANI) and sodium alginate (SA). Initially, SA acts as a proton reservoir for PANI in an aqueous system, enhancing the doping level of PANI and improving its electrical conductivity. Additionally, PANI and SA chains respond to diverse polar solvents, such as water, acetonitrile, ethanol, n-hexane, and air, inducing distinct conformations that affect the degree of PANI conjugation and electron migration along the chains. This process is reversible and non-destructive to the polymer chain, ensuring the effective and uncompromised performance of the EMI shielding switch. We can achieve precise and reversible tuning (on/off) of EMI shielding with different effectiveness levels by manipulating the solvents within the framework. This work opens a new solvent-stimuli avenue for the development of EMI shielding materials with reliable and intelligent on/off switching capabilities.

Robust and Flame-Retardant Zylon Aerogel Fibers for Wearable Thermal Insulation and Sensing in Harsh Environment

The exceptional lightweight, highly porous, and insulating properties of aerogel fibers make them ideal for thermal insulation. However, current aerogel fibers face limitations due to their low resistance to harsh environments and a lack of intelligent responses. Herein, a universal strategy for creating polymer aerogel fibers using crosslinked nanofiber building blocks is proposed. This approach combines controlled proton absorption gelation spinning with a heat-induced crosslinking process. As a proof-of-concept, Zylon aerogel fibers that exhibited robust thermal stability (up to 650 °C), high flame retardancy (limiting oxygen index of 54.2%), and extreme chemical resistance are designed and synthesized. These fibers possess high porosity (98.6%), high breaking strength (8.6 MPa), and low thermal conductivity (0.036 W m-1 K-1 ). These aerogel fibers can be knotted or woven into textiles, utilized in harsh environments (-196-400 °C), and demonstrate sensitive self-powered sensing capabilities. This method of developing aerogel fibers expands the applications of high-performance polymer fibers and holds great potential for future applications in wearable smart protective fabrics.

Ultra-flexible silver/iron nanowire decorated melamine composite foams for high-efficiency electromagnetic wave absorption and thermal management

Nowadays, functional electronic devices with excellent flexibility and thermal management capability for effective electromagnetic wave absorption are urgently in demand. Herein, a novel and highly flexible silver nanowire (AgNW)/iron nanowire (FeNW) decorated melamine composite foam (AgFe-MF) was prepared via simple dip-coating process. Owing to optimal impedance matching, synergistic dielectric and magnetic losses as well as three-dimensional porous structure, the AgFe-MF with an ultra-low filler content (0.22 vol%) exhibited an outstanding minimum reflection loss of -69.61 dB, and the best effective absorption bandwidth (EAB) could reach up to 6.37 GHz. Importantly, the EAB of long-time working AgFe-MF was enhanced to 7.01 GHz after 1000 compress-release cycles under 40 % strain. Besides, it also featured considerate Joule heating capacity and achieved a saturation temperature of over 85.7 ℃ under 2.6 V voltage. The impressive thermal isolation and long-term stability ensured the safety used as portable heater. Therefore, this work will provide a vital slight for fabricating smart wearable electronic devices with integrated anti-electromagnetic radiation and personalized thermal management performances towards potential thermal and health threats.

Silver nanowire-infused carbon aerogel: A multifunctional nanocellulose-derived material for personal thermal management

Personal thermal management (PTM) textiles for outdoor activities have become increasingly important for addressing energy consumption and thermal comfortable. Cellulose nanofiber (CNF) aerogels have emerged as promising candidates for PTM due to the eco-friendliness, lightweight, and low thermal conductivity. However, the singular insulation capability may not be sufficient to accommodate the diverse and harsh outdoor conditions. Herein, we carbonized CNF-based aerogel to fabricate anisotropic carbon aerogels, and then incorporated silver nanowires (AgNWs) upon onside to fabricate the dual-function AgNWs/carbon aerogel. The resulting material inherits high porosity (99.3 %), high surface area (503.2 m2/g), low density (7.08 mg/cm3), and low thermal conductivity (18.2 mW·m-1·k-1 in the axial direction) to act as an ideal thermal insulator. The AgNWs coating side demonstrates low IR-emissivity (17.6 % at 7-14 μm) and the carbon aerogel side has high solar absorptivity (91.97 %). Moreover, the AgNWs/carbon aerogel shows Joule heating performance (∆T = 44.5 °C within 3 min at 5 V). The multi-heating modes enabling self-adaptable thermal comfortable under various harsh environment. Additionally, the material's breathability, permeability, and electromagnetic shielding characteristics also make it suitable candidate for advanced wearable textiles for PTM.

Data-Driven oriented diatomic doping strategy to customize frequency dispersion for considerable microwave absorption

The electromagnetic (EM) parameters are the key factors to decode the complex microwave absorption properties, including matching thickness, absorption bandwidth and intensity. Numerous works hence have been focused on optimizing EM parameters to reinforce the comprehensive absorption performance, while most of the adopted experimental means still remain in sporadic and random attempts. In this work, the data-driven approach is first employed to forecast that a fierce frequency-dispersion of permittivity is necessary for the broad absorption, and the appropriate magnetic component can mitigate this elusive trend of required permittivity. Oriented by the simulated results, the B/N diatomic doped C/Fe3C magnetoelectric composites are successfully constructed, aiming at the precise regulation of electronic properties to achieve these specially customized EM parameters by forming multi-polarization resonances. The results demonstrate that the introduction of N defects and B defects could enrich the types of dipole pairs (CN, C-B, CNB, vacancy, etc.) and thus activate multi-polarization behavior. The charge density differences calculated by the first-principle further demonstrate that the occupation of B for C bonded with Pyridinic-N and Pyrrolic-N contributes to intense polarization behaviors over the lower frequency range. As a result, excellent microwave absorption properties can be finally achieved with an effective absorbing bandwidth reaching 7.2 GHz at 2.1 mm, implying that the joint use of data-driven and doping engineering strategies to customize frequency dispersion characteristics provides precious guidelines for boosting microwave absorption performance.

Hierarchical Fe-Co@TiO2 with Incoherent Heterointerfaces and Gradient Magnetic Domains for Electromagnetic Wave Absorption

Induced polarization response and integrated magnetic resonance show prosperous advantages in boosting electromagnetic wave absorption but still face huge challenges in revealing the intrinsic mechanism. In this work, we propose a self-confined strategy to construct hierarchical Fe-Co@TiO2 microrods with numerous incoherent heterointerfaces and gradient magnetic domains. The results demonstrate that the use of polyvinylpyrrolidone (PVP) coating is crucial for the subsequent deposition of Co-zeolitic imidazolate frameworks (ZIF-67), the distance of ordered arranged metal ions manipulates the size of magnetic domains, and the pyrolysis of PVP layers restricts the eutectic process of Fe-Co alloys to some extent. As a result, these introduced lattice defects, oxygen vacancies, and incoherent heterointerfaces inevitably generate a strong polarization response, and the regulated gradient magnetic domains realize integrated magnetic resonance, including macroscopic magnetic coupling, long-range magnetic diffraction, and nanoscale magnetic bridge connection, and both of the intrinsic mechanisms in dissipating electromagnetic energy are quantitatively clarified by Lorentz off-axis electron holography. Owing to the cooperative merits, the Fe-Co@TiO2 absorbents exhibit enhanced absorption intensity and strong absorption bandwidth. This study inspires us to develop a generalized strategy for manipulating the size of magnetic domains, and the integrated magnetic resonance theory provides a versatile methodology in clarifying magnetic loss mechanism.

Advanced multifunctional IGBT packing materials with enhanced thermal conductivity and electromagnetic wave absorption properties

Insulated-Gate Bipolar Transistors (IGBT) face limitations in high-frequency electronic applications due to heat accumulation and electromagnetic interference issues. To address these challenges, it is crucial to develop packing materials with excellent electromagnetic interference immunity and heat dissipation properties. In this research, a novel epoxy-based packing material (MDCF@C-ZrO2/EP) with high electromagnetic wave absorption and exceptional thermal transport properties was produced by employing a unique three-dimensional carbon structure-induced nanomaterial dispersion strategy. In particular, the three-dimensional MDCF structure effectively prevents packing agglomeration and fosters the formation of an abundant hetero-interface between MDCF and C-ZrO2, leading to improved impedance matching and enhanced electromagnetic wave dissipation capabilities. Remarkably, even at a mere 5 wt% filling level, the material demonstrates an impressive reflection loss value of -58.92 dB and a wide effective absorption bandwidth of 6.68 GHz, effectively covering the entire Ku-band. Additionally, the 3D MDCF@C-ZrO2 significantly enhances the phonon transport path and elevates the thermal conductivity of pure epoxy resin by an impressive ∼ 150%. As a result, this innovative research holds tremendous potential in enabling the application of IGBTs in high-power and high-frequency electronic components, while also contributing to the advancement of next-generation wireless communications and smart devices.

Advancements in Microwave Absorption Motivated by Interdisciplinary Research

Microwave absorption materials (MAMs) are originally developed for military purposes, but have since evolved into versatile materials with promising applications in modern technologies, including household use. Despite significant progress in bench-side research over the past decade, MAMs remain limited in their scope and have yet to be widely adopted. This review explores the history of MAMs from first-generation coatings to second-generation functional absorbers, identifies bottlenecks hindering their maturation. It also presents potential solutions such as exploring broader spatial scales, advanced characterization, introducing liquid media, utilizing novel toolbox (machine learning, ML), and proximity of lab to end-user. Additionally, it meticulously presents compelling applications of MAMs in medicine, mechanics, energy, optics, and sensing, which go beyond absorption efficiency, along with their current development status and prospects. This interdisciplinary research direction differs from previous research which primarily focused on meeting traditional requirements (i.e., thin, lightweight, wide, and strong), and can be defined as the next generation of smart absorbers. Ultimately, the effective utilization of ubiquitous electromagnetic (EM) waves, aided by third-generation MAMs, should be better aligned with future expectations.

Mimicking polar bear hairs in aerogel fibers

Encapsulated aerogel fibers offer thermal insulation, breathability, and strength.

Fast and scalable production of crosslinked polyimide aerogel fibers for ultrathin thermoregulating clothes

Polyimide aerogel fibers hold promise for intelligent thermal management fabrics, but their scalable production faces challenges due to the sluggish gelation kinetics and the weak backbone strength. Herein, a strategy is developed for fast and scalable fabrication of crosslinked polyimide (CPI) aerogel fibers by wet-spinning and ambient pressure drying via UV-enhanced dynamic gelation strategy. This strategy enables fast sol-gel transition of photosensitive polyimide, resulting in a strongly-crosslinked gel skeleton that effectively maintains the fiber shape and porous nanostructure. Continuous production of CPI aerogel fibers (length of hundreds of meters) with high specific modulus (390.9 kN m kg-1) can be achieved within 7 h, more efficiently than previous methods (>48 h). Moreover, the CPI aerogel fabric demonstrates almost the same thermal insulating performance as down, but is about 1/8 the thickness of down. The strategy opens a promisingly wide-space for fast and scalable fabrication of ultrathin fabrics for personal thermal management.

Ni-Carbon Microtube/Polytetrafluoroethylene as Flexible Electrothermal Microwave Absorbers

Flexible microwave absorbers with Joule heating performance are urgently desired to meet the demands of extreme service environments. Herein, a type of flexible composite film is constructed by homogeneously dispersing a hierarchical Ni-carbon microtube (Ni/CMT) into a processable polytetrafluoroethylene (PTFE) matrix. The Ni/CMT are interconnected into a 3D conductive network, in which the huge interior cavity of the carbon microtube (CMT) improves impedance matching and provides additional hyper channels for electromagnetic (EM) waves dissipation, and the hierarchical magnetic Ni nanoparticles enhance the synergistic interactions between confined heterogeneous interfaces. Such an ingenious structure endows the composites with excellent electrothermal performance and improves their serviceability for application under extreme environments. Moreover, under a low fill loading of 3 wt.%, the Ni/CMT/PTFE (NCP) can achieve excellent low-frequency microwave absorption (MA) property with a minimum reflection loss of -59.12 dB at 5.92 GHz, which covers almost the entire C-band. Relying on their brilliant MA property, an EM sensor is designed and achieved by the resonance coupling of the patterned NCP. This work opens up a new way for the design of next-generation microwave absorbers that meet the requirements of EM packaging, proofing water and removing ice, fire safety, and health monitoring.

Facile and efficient chitosan-based hygroscopic aerogel for air dehumidification

Sorption dehumidification, as an energy-saving and eco-friendly approach, has been emerging in application for air dehumidification. Here, a prospective method is proposed to prepare biomass-based hygroscopic aerogels that are easily applicable, sustainable, high-efficient, and recyclable. The chitosan-based aerogel with a porous and hydrophilic network acts as the carrier and water reservoir for the uniformly distributed lithium chloride hygroscopic salt, and provides the hygroscopic salt with more liberal water channels to facilitate moisture capture and transfer. As a consequence, the prepared chitosan/polyvinyl alcohol@lithium chloride (chitosan/PVA@LiCl) hygroscopic aerogel exhibits an excellent moisture absorption capacity of up to 2.77 g g-1 at a relative humidity of 90 %. Meanwhile, as the chitosan/PVA@LiCl aerogel is set in a closed space about 2200 times larger than its own volume, the relative humidity can be reduced from 90 % to 32 % within 2 h, and further lower to 25 % after 4 h. Furthermore, combined with multi-walled carbon nanotubes, the photothermal hygroscopic aerogel is obtained that can rapidly desorb water under sunlight, thus to realize energy-free cycle. Overall, the renewable biomass-based aerogel materials with the advantages of simple preparation and excellent hygroscopic performance provides a new path for the development of sorption dehumidification technology.

Research progress and future perspectives on electromagnetic wave absorption of fibrous materials

Electromagnetic waves have caused great harm to military safety, high-frequency electronic components, and precision instruments, and so forth, which urgently requires the development of lightweight, high-efficiency, broadband electromagnetic waves (EMW) absorbing materials for protection. As the basic fibrous materials, carbon fibers (CFs) and SiC fibers (SiCf) have been widely applied in EMW absorption due to their intrinsic characteristics of low density, high mechanical properties, high conductivity, and dielectric loss mechanism. Nevertheless, it has remained a great challenge to develop lightweight EMW-absorbing fibrous materials with strong absorption capability and broad frequency range. In this review, the fundamental electromagnetic attenuation mechanisms are firstly introduced. Furthermore, the preparation, structure, morphology, and absorbing performance of CFs and SiCf-based EMW absorbing composites are summarized. In addition, prospective research opportunities are highlighted toward the development of fibrous absorbing materials with the excellent absorption performance.

Bioinspired Thermochromic Textile Based on Robust Cellulose Aerogel Fiber for Self-Adaptive Thermal Management and Dynamic Labels

Aerogel fiber has emerged recently for incorporation in personal thermal management textiles due to its flexibility, scalability, and ultrahigh porosity, which allows the body to keep warm via thermal isolation without energy consumption. However, the functionalization and intellectualization of cellulose-based aerogel fibers have not yet been fully developed. Herein, we propose a biomimicking design inspired by polar bear and Siamese cat hair that combines porous cellulose aerogel fiber (CAF) with reversible thermochromic microcapsules to mimic biological sensory and adaptive thermoregulation functions. The produced CAF has a controllable pore structure, a large specific surface area (230 m2/g), and excellent mechanical strength (∼15 MPa). Low-temperature darkening microcapsules have been incorporated into the robust CAF to spontaneously adjust color by perceiving the ambient temperature. The functional aerogel fiber fabric achieves high thermal insulation and photothermal modulation simultaneously at temperatures below 18 °C. The temperature of the thermochromic fabric was higher by 6 °C than that of the sample without the microcapsules at a light intensity of 0.2 W/cm2. In addition, the aerogel fibers mixed with two types of thermochromic microcapsules exhibit three color switches with fast response, a color-control precision of 0.2 °C, and good cycling performance. This smart aerogel fibers hold great promise for self-adaptive thermal management, temperature indication, information transfer, and anticounterfeiting in textiles.