Semi-Interpenetrating Polymer Network Anion Exchange Membranes Based on Quaternized Polybenzoxazine and Poly(Vinyl Alcohol-Co-Ethylene) for Acid Recovery by Diffusion Dialysis

Acid recovery from acidic waste is a pressing issue in current times. Chemical methods for recovery are not economically feasible and require significant energy input to save the environment. This study reported a semi-interpenetrating polymer network (semi-IPN) anion exchange membranes (AEMs) for acid recovery by diffusion dialysis with excellent dimensional stability, high oxidation stability, good acid dialysis coefficient (UH +) and high separation factor (S). Semi-IPN AEMs are prepared by ring-open cross-linked quaternized polybenzoxazine (AQBZ) with poly(vinyl alcohol-co-ethylene), where AQBZ is obtained by Mannich reaction and Menshutkin reaction. All four proportions of semi-IPNs exhibit clear micro-phase separation, which is conducive to ion transport. The water uptake (WU) of the four semi-IPNs ranges from 14.2 % to 19.2 %, while the swelling ratio (SR) remains between 8.7 % and 11.3 %. These results indicate that the cross-linked structure in the designed semi-IPNs effectively control swelling and ensure dimensional stability. The thermal degradation temperature (Td5) of semi-IPN4:6 to semi-IPN7:3 varies from 309 °C to 289 °C, with an oxidation stability weight loss rate (WOX) ranging from 91.5 % to 93.5 %, demonstrating excellent thermal stability and oxidation stability. The semi-IPNs also show good UH + values ranging from 11.9-16.3*10-3 m/h and high S values between 38.6 and 45.9, indicating the promising potential of the semi-IPNs.

Oxygen-Containing Quaternary Phosphonium Salts (oxy-QPSs): Synthesis, Properties, and Cellulose Dissolution

In the present study, the synthesis of oxygen-containing quaternary phosphonium salts (oxy-QPSs) was described. Within this work, structure-property relationships of oxy-QPSs were estimated by systematic analysis of physical-chemical properties. The influence of the oxygen-containing substituent was examined by comparing the properties of oxy-QPSs in homology series as well as with phosphonium analog-included alkyl side chains. The crystal structure analysis showed that the oxygen introduction influences the conformation of the side chain of the oxy-QPS. It was found that oxy-QPSs, using an aprotic co-solvent, dimethylsulfoxide (DMSO), can dissolve microcrystalline cellulose. The cellulose dissolution in oxy-QPSs appeared to be dependent on the functional group in the cation and anion nature. For the selected conditions, dissolution of up to 5 wt% of cellulose was observed. The antimicrobial activity of oxy-QPSs under study was expected to be low. The biocompatibility of oxy-QPSs with fermentative microbes was tested on non-pathogenic Saccharomyces cerevisiae, Lactobacillus plantarum, and Bacillus subtilis. This reliably allows one to safely address the combined biomass destruction and enzyme hydrolysis processes in one pot.

Anti-Fouling Properties of Phosphonium Ionic Liquid Coatings in the Marine Environment

Biofouling is the buildup of marine organisms on a submerged material. This research tests the efficacy of phosphonium ion gels comprising phosphonium monomers ([P444VB][AOT] and [P888VB][AOT]) and free ionic liquid ([P4448][AOT], [P88814][AOT]) (10 to 50 wt%), varying copper(II) oxide biocide concentrations (0 to 2 wt%), and the docusate anion [AOT]- for added hydrophobicity. The efficacy of these formulations was tested using a seachest simulator protected from light and tidal currents in New Zealand coastal waters over the summer and autumn periods. Anti-fouling performance was correlated with the hydrophobicity of the surface (water contact angle: 14-131°) and biocide concentration. Formulations with higher hydrophobicity (i.e., less free ionic liquid and longer alkyl chain substituents) displayed superior anti-fouling performance. The presence of the copper(II) biocide negatively affected anti-fouling performance via significant increases to hydrophilicity. No correlation was observed between antimicrobial activity and anti-fouling performance. Overall, phosphonium ion gels show potential for combining anti-fouling and foul release properties.

Design of Thermoplastic Polyurethanes with Conferred Antibacterial, Mechanical, and Cytotoxic Properties for Catheter Application

Thermoplastic polyurethanes (TPUs) are proposed as suitable solution for the fabrication of biocompatible catheters with appropriate mechanical parameters and confirmed antibacterial and cytocompatible properties. For this purpose, a series of quaternary ammonium salts (QASs) and quaternary phosphonium salts (QPSs) based monomers were prepared followed by the determination of their minimal inhibitory concentrations (MICs) against Gram-positive Staphylococcus aureus (S. aureus) and Gram-negative Pseudomonas aeruginosa (P. aeruginosa). A combination of the most active ammonium (QAS-C₁₄) and phosphonium (QPS-TOP) salts led to a MIC down to 2.4 μg/mL against S. aureus and 9 μg/mL against P. aeruginosa, corroborating the existence of a synergistic effect. These quaternary onium salt (QOS) units were successfully incorporated along the polymer chain, as part of a two-step synthesis approach. The resulting TPU-QOS materials were subsequently characterized through thermal, mechanical, and surface analyses. TPU-Mix (combining the most active QAS-C₁₄ and QPS-TOP units) showed the highest antibacterial efficiency, confirming the synergistic effect between both QOS groups. Finally, an MTT assay on the SiHa cell line revealed the low cytotoxicity level of these polymeric films, making these materials suitable for biomedical application. To go one step further in the preindustrialization approach, proof of concept regarding the catheter prototype fabrication based on TPU-QAS/QPS was validated by extrusion.

Access to thermally robust and abrasion resistant antimicrobial plastics: synthesis of UV-curable phosphonium small molecule coatings and extrudable additives

The threat of antibiotic-resistant, biofilm-forming bacteria necessitates a preventative approach to combat the proliferation of robust, pathogenic strains on "high touch surfaces" in the food packaging, biomedical, and healthcare industries. The development of both biocide-releasing and tethered, immobilized biocide surface coatings has risen to meet this demand. While these surface coatings have demonstrated excellent antimicrobial efficacy, there are few examples of antimicrobial surfaces with long-term durability and performance. To this end, UV-curable phosphoniums bearing benzophenone anchors with either an alkyl, aryl, or fluoroalkyl group were synthesized and their efficacy as thermally stable antimicrobial additives in extruded plastics or as surface attached coatings probed. The surface topology and characteristics of these materials were studied to gain insight into the mechanism of their antimicrobial activity. Efficacy against both Gram negative and Gram positive bacteria as either a coating or additive showed compete reductions of the initial bacterial load. Crucially, the materials maintained the ability to kill biofilm-forming bacteria even after being subject to several cycles of abrasion.

"Lignophines": lignin-based tertiary phosphines with metal-scavenging ability

Methacrylated lignin was reacted with PH₃(g) to prepare a phosphorus rich bio-based polymer containing PH/PH₂ functional groups, which were converted to tertiary phosphine units via the phosphane-ene reaction. This represents a straightforward method for the upconversion of low-value biomass waste to useful inorganic polymer with potential utility in metal scavenging applications.

UV-Curable Surface-Attached Antimicrobial Polymeric Onium Coatings: Designing Effective, Solvent-Resistant Coatings for Plastic Surfaces

Contact-active ammonium and phosphonium antimicrobial polymeric coatings grafted to plastic surfaces by UV treatment are described. Robust, antimicrobial styrenic polymeric scaffolds copolymerized with a low loading of UV-curable benzophenone were prepared by nitroxide-mediated polymerization (NMP). Similar reversible addition-fragmentation chain-transfer (RAFT)-controlled radical polymerizations were attempted for comparison. These random styrenics were further functionalized into partially quaternarized water-soluble cationic polymers. UV-cured polymeric thin film coatings possessing cationic groups with n-alkyl substituents of n ≤ 2 demonstrate antimicrobial properties against both Gram-positive and Gram-negative bacteria, while species containing bulkier or longer substituents were biologically inactive. The UV-cured cationic antimicrobial polymeric onium thin films also demonstrate enhanced abrasion and chemical resistance.

Phosphonium Polyelectrolyte Complexes for the Encapsulation and Slow Release of Ionic Cargo

Polyelectrolyte complexation, the combination of anionically and cationically charged polymers through ionic interactions, can be used to form hydrogel networks. These networks can be used to encapsulate and release cargo, but the release of cargo is typically rapid, occurring over a period of hours to a few days and they often exhibit weak, fluid-like mechanical properties. Here we report the preparation and study of polyelectrolyte complexes (PECs) from sodium hyaluronate (HA) and poly[tris(hydroxypropyl)(4-vinylbenzyl)phosphonium chloride], poly[triphenyl(4-vinylbenzyl)phosphonium chloride], poly[tri(n-butyl)(4-vinylbenzyl)phosphonium chloride], or poly[triethyl(4-vinylbenzyl)phosphonium chloride]. The networks were compacted by ultracentrifugation, then their composition, swelling, rheological, and self-healing properties were studied. Their properties depended on the structure of the phosphonium polymer and the salt concentration, but in general, they exhibited predominantly gel-like behavior with relaxation times greater than 40 s and self-healing over 2-18 h. Anionic molecules, including fluorescein, diclofenac, and adenosine-5'-triphosphate, were encapsulated into the PECs with high loading capacities of up to 16 wt %. Fluorescein and diclofenac were slowly released over 60 days, which was attributed to a combination of hydrophobic and ionic interactions with the dense PEC network. The cytotoxicities of the polymers and their corresponding networks with HA to C2C12 mouse myoblast cells was investigated and found to depend on the structure of the polymer and the properties of the network. Overall, this work demonstrates the utility of polyphosphonium-HA networks for the loading and slow release of ionic drugs and that their physical and biological properties can be readily tuned according to the structure of the phosphonium polymer.

Structure-function relationships of nonviral gene vectors: Lessons from antimicrobial polymers

In recent years, substantial advances have been achieved in the design and synthesis of nonviral gene vectors. However, lack of effective and biocompatible vectors still remains a major challenge that hinders their application in clinical settings. In the past decade, there has been a rapid expansion of cationic antimicrobial polymers, due to their potent, rapid, and broad-spectrum biocidal activity against resistant microbes, and biocompatible features. Given that antimicrobial polymers share common features with nonviral gene vectors in various aspects, such as membrane affinity, functional groups, physicochemical characteristics, and unique macromolecular architectures, these polymers may provide us with inspirations to overcome challenges in the design of novel vectors toward more safe and efficient gene delivery in clinic. Building off these observations, we provide here an overview of the structure-function relationships of polymers for both antimicrobial applications and gene delivery by elaborating some key structural parameters, including functional groups, charge density, hydrophobic/hydrophilic balance, MW, and macromolecular architectures. By borrowing a leaf from antimicrobial agents, great advancement in the development of newer nonviral gene vectors with high transfection efficiency and biocompatibility will be more promising. STATEMENT OF SIGNIFICANCE: The development of gene delivery is still in the preclinical stage for the lack of effective and biocompatible vectors. Given that antimicrobial polymers share common features with gene vectors in various aspects, such as membrane affinity, functional groups, physicochemical characteristics, and unique macromolecular architectures, these polymers may provide us with inspirations to overcome challenges in the design of novel vectors toward more safe and efficient gene delivery in clinic. In this review, we systematically summarized the structure-function relationships of antimicrobial polymers and gene vectors, with which the design of more advanced nonviral gene vectors is anticipated to be further boosted in the future.

A facile one-step grafting of polyphosphonium onto halloysite nanotubes initiated by Ce(iv)

Polyphosphonium was facilely grafted onto HNTs in an aqueous phase by a one-step method initiated by Ce(iv) at a mild temperature.

Effect of Counterions on the Self-Assembly of Polystyrene-Polyphosphonium Block Copolymers

The ability to manipulate block copolymers on the nanoscale has led to many scientific and technological advances. These include nanoscale ordered bulk and thin films and also solution phase components; these are promising materials for making smaller ordered electronics, selective membranes, and also biomedical applications. The ability to manipulate block copolymer material architectures on such small scales has risen from thorough investigations into the properties that affect the architectures. Polyelectrolytes are an important class of polymers that are used to make amphiphilic block copolymers. In this context the authors synthesized polystyrene-b-polyphosphonium block copolymers with different anions coordinated to the polyphosphonium block in order to study the effect of the anion on the aqueous self-assembly of the polymers. The anions play an important role in the solubility of the monomeric materials which results in differences in the self-assembly observed through dynamic light scattering and transmission electron microscopy.

Antimicrobial Polymers in the Nano-World

Infections are one of the main concerns of our era due to antibiotic-resistant infections and the increasing costs in the health-care sector. Within this context, antimicrobial polymers present a great alternative to combat these problems since their mechanisms of action differ from those of antibiotics. Therefore, the microorganisms' resistance to these polymeric materials is avoided. Antimicrobial polymers are not only applied in the health-care sector, they are also used in many other areas. This review presents different strategies that combine nanoscience and nanotechnology in the polymer world to combat contaminations from bacteria, fungi or algae. It focuses on the most relevant areas of application of these materials, viz. health, food, agriculture, and textiles.

Phosphonium-Functionalized Polymer Micelles with Intrinsic Antibacterial Activity

New approaches to treat bacterial infections are badly needed to address the increasing problem of antibiotic resistance. This study explores phosphonium-functionalized block copolymer micelles as intrinsically antibacterial polymer assemblies. Phosphonium cations with varying alkyl lengths were conjugated to the terminus of a poly(ethylene oxide)-polycaprolactone block copolymer, and the phosphonium-functionalized block copolymers were self-assembled to form micelles in aqueous solution. The size, morphology, and ζ-potential of the assemblies were studied, and their abilities to kill Escherichia coli and Staphylococcus aureus were evaluated. It was found that the minimum bactericidal concentration depended on the phosphonium alkyl chain length, and different trends were observed for Gram-negative and Gram-positive bacteria. The most active assemblies exhibited no hemolysis of red blood cells above the bactericidal concentrations, indicating that they can selectively disrupt the membranes of bacteria. Furthermore, it was possible to encapsulate and release the antibiotic tetracycline using the assemblies, providing a potential multimechanistic approach to bacterial killing.

A bacteria-activated photodynamic nanosystem based on polyelectrolyte-coated silica nanoparticles

A novel bacteria-activated photodynamic nanosystem (SiO₂/PAH–Ce6) has been reported for selective fluorescence sensing and photodynamic elimination of pathogenic bacteria.