Braiding kinetics and spectroscopy in photo-catalysis: the spectro-kinetic approach

Kinetic modeling of the photocatalytic degradation of acetaminophen and its main transformation products

In this study, a kinetic model of the heterogeneous photocatalytic degradation of acetaminophen and its main transformation products is presented. Kinetic photocatalytic modeling and photon absorption rate modeling were included. Monte Carlo method was used to model the photon absorption process. Experiments were carried out in a reactor operated in batch mode and TiO2 nanotubes were used as photocatalyst irradiated with 254 nm UVC. Kinetic parameters were estimated from the experiments data by applying a non-linear regression procedure. Intrinsic expressions to the kinetics of acetaminophen degradation and its main transformation products were derived. Model, kinetics and photon absorption formulations and parameters proved to be affordable for describing the photocatalytic degradation of acetaminophen, but improvements should be done for better description of formation and oxidation kinetics of main transformation products. The model should be tested with other pharmaceuticals and emergent pollutants to calibrate it and evaluate its applicability in a wide range of compounds.

Photocatalytic degradation process of antibiotic sulfamethoxazole by ZnO in aquatic systems: a dynamic kinetic model based on contributions of OH radical, oxygenated radical intermediates and dissolved oxygen

The photocatalytic degradation process of sulfamethoxazole (SMX) using ZnO in aquatic systems has been systematically studied by varying initial SMX concentration from 0 to 15 mgL-1, ZnO dosage from 0 to 4 gL-1 and UV light intensity at the light source from 0 to 18 W(m-lamp length)-1 at natural pH. Almost complete degradations of SMX were achieved within 120 min for the initial SMX concentration ≤15 mgL-1 with ZnO dosage of 3 gL-1 and UV light intensity of 18 W(m-lamp length)-1. The photocatalytic degradation process was found to be interacted with the dissolved oxygen (DO) consumption. With oxygen supply through the gas-liquid free-surface, the DO concentration decreased significantly in the initial SMX degradation phase and increased asymptotically to the saturated DO concentration after achieving about 80% SMX degradation. The change in DO concentration was probably controlled by the oxygen consumption in the formation of oxygenated radical intermediates. A novel dynamic kinetic model based on the fundamental reactions of photocatalysis and the formation of oxygenated radical intermediates was developed. In the modeling the dynamic concentration profiles of OH radical and DO are considered. The dynamics of SMX degradation process by ZnO was simulated reasonably by the proposed model.

Topologically Porous Heterostructures for Photo/Photothermal Catalysis of Clean Energy Conversion

As a straightforward way to fix solar energy, photo/photothermal catalysis with semiconductor provides a promising way to settle the energy shortage and environmental crisis in many fields, especially in clean energy conversion. Topologically porous heterostructures (TPHs), featured with well-defined pores and mainly composed by the derivatives of some precursors with specific morphology, are a major part of hierarchical materials in photo/photothermal catalysis and provide a versatile platform to construct efficient photocatalysts for their enhanced light absorption, accelerated charges transfer, improved stability, and promoted mass transportation. Therefore, a comprehensive and timely review on the advantages and recent applications of the TPHs is of great importance to forecast the potential applications and research trend in the future. This review initially demonstrates the advantages of TPHs in photo/photothermal catalysis. Then the universal classifications and design strategies of TPHs are emphasized. Besides, the applications and mechanisms of photo/photothermal catalysis in hydrogen evolution from water splitting and CO_x hydrogenation over TPHs are carefully reviewed and highlighted. Finally, the challenges and perspectives of TPHs in photo/photothermal catalysis are also critically discussed.

Green Thermo-Photo Catalytic Production of Syngas Using Pd/Nb-TiO2 Catalysts

In this contribution, a series of Pd-promoted Nb-doped titania samples were essayed in the gas-phase thermo-photo production of syngas from methanol/water mixtures. The Pd loading was tested in the 0.1 to 2.5 wt % range, leading to the presence of metallic nanoparticles under reaction. Reaction rates exceeding 52 mmol H₂ g^-1 h^-1 and quantum efficiencies above 33% were obtained. The optimum sample having a 0.5 wt % of Pd provided an outstanding synergy between light and heat under reaction conditions, facilitating the boost of activity with respect to the single-source processes and achieving high selectivity to syngas. The spectroscopic analysis of the physico-chemical ground of the activity unveiled that the noble metal interaction with the Nb-doped anatase support triggers a cooperative effect, promoting the evolution of formic acid-type methanol-derived carbon-containing species and rendering a significant enhancement of syngas production. The proposed thermo-photo system is thus a firm candidate to contribute to the new green circular economy.

Reaction Kinetics of Photoelectrochemical CO2 Reduction on a CuBi2O4-Based Photocathode

The CO₂ reduction reaction (CO₂RR) is an essential step in natural photosynthesis and artificial photosynthesis to provide carbohydrate foods and hydrocarbon energy in the carbon-neutral cycle. However, the current solar conversion efficiencies and/or product selectivity of the CO₂RR are very sluggish due to its complicated multiple-step charge transfer reactions. Here, we systematically investigate the charge transfer reaction rate during CO₂ reduction on CuBi₂O₄ photocathodes, where the surface is modified with 3-aminopropyltriethoxysilane (APTES). We discover that the surface amine group increases the charge separation rate, significantly enhancing the surface charge transfer reaction rate. However, the surface acidity has less influence on the first-order reaction, indicating that a rate-determining step (RDS) exists in the early stage of the photoelectrochemical cell (PEC) processes. Moreover, the intensity-modulated photocurrent spectroscopy (IMPS) confirms that both surface charge transfer and the recombination rate on APTES-coated CuBi₂O₄ are larger than bare CuBi₂O₄ while possessing comparable charge transfer efficiencies. Overall, the surface charge transfer reactions under the PEC condition require designing more effective nanostructured photoelectrodes and powerful characterization methods to intrinsically increase the charge separation and transfer rate while reducing the recombination rate.

H2 Photoproduction Efficiency: Implications of the Reaction Mechanism as a Function of the Methanol/Water Mixture

The influence of the reaction pathway of the sacrificial molecule oxidation to generate hydrogen is here investigated for lean and rich methanol reaction mixtures. Pt-TiO2 powders promoted or not with tin sulfide were used as catalysts. With the help of in situ infrared experiments under reaction conditions, methanol evolution was shown to take place by hole-related oxidation steps, with alkoxy and carbon-centered species as key radical species. The study analyzed quantitatively the fate and chemical use of the photons absorbed by the solids with the help of the quantum efficiency and the useful fraction of photons observables. Within this framework, the role of the sulfide component to promote photoactivity is interpreted, braiding chemical and photonic information.

Photothermal synergy for efficient dry reforming of CH4 by Ag/AgBr/CsPbBr3 composite

Dry reforming of CH4 by photothermal catalysis is considered to be a promising approach to produce syngas. It can not only store useful chemical energy, but also consume CO2 and...

Observation of 4th-order water oxidation kinetics by time-resolved photovoltage spectroscopy

Artificial photo-driven water oxidation has been proposed over half a century through a four-charge involved multiple-step oxygen evolution process. However, the knowledge of the intrinsic activity, such as the rate-law of the water oxidation reactions, has been inadequately studied. Up to date, the highest order reported is the third one under photoelectrochemical condition. In this work, we identified the fourth-order charge decay reactions on hematite by using a time-resolved surface photovoltage probe technique. A theoretical turnover frequency (TOF) > 100 nm^-2·s^-1 can be expected for O₂ molecules when the hole density >0.1 nm^-2. This work demonstrates a facile and robust method to investigate the high-order reaction kinetics. More excitingly, this research built the bridge between the rate-law, rate-determining step, and energy barrier of intermediates.

Kinetic analysis of the partial synthesis of artemisinin: Photooxygenation to the intermediate hydroperoxide

The price of the currently best available antimalarial treatment is driven in large part by the limited availability of its base drug compound artemisinin. One approach to reduce the artemisinin cost is to efficiently integrate the partial synthesis of artemisinin starting from its biological precursor dihydroartemisinic acid (DHAA) into the production process. The optimal design of such an integrated process is a complex task that is easier to solve through simulations studies and process modelling. In this article, we present a quantitative kinetic model for the photooxygenation of DHAA to an hydroperoxide, the essential initial step of the partial synthesis to artemisinin. The photooxygenation reactions were studied in a two-phase photo-flow reactor utilizing Taylor flow for enhanced mixing and fast gas-liquid mass transfer. A good agreement of the model and the experimental data was achieved for all combinations of photosensitizer concentration, photon flux, fluid velocity and both liquid and gas phase compositions. Deviations between simulated predictions and measurements for the amount of hydroperoxide formed are 7.1 % on average. Consequently, the identified and parameterized kinetic model is exploited to investigate different behaviors of the reactor under study. In a final step, the kinetic model is utilized to suggest attractive operating windows for future applications of the photooxygenation of DHAA exploiting reaction rates that are not affected by mass transfer limitations.

Heterogeneous Photocatalysis

Heterogeneous photocatalysis is a subtype of catalysis that refers to chemical processes catalysed by a semiconductor solid under proper illumination conditions [...]

Nature-inspired hierarchical materials for sensing and energy storage applications

Nature-inspired hierarchical architectures have recently drawn enormous interest in the materials science community, being considered as promising materials for the development of high-performance wearable electronic devices. Their highly dynamic interfacial interactions have opened new horizons towards the fabrication of sustainable sensing and energy storage materials with multifunctional properties. Nature-inspired assemblies can exhibit impressive properties including ultrahigh sensitivity, excellent energy density and coulombic efficiency behaviors as well as ultralong cycling stability and durability, which can be finely tuned and enhanced by controlling synergistic interfacial interactions between their individual components. This tutorial review article aims to address recent breakthroughs in the development of advanced Nature-inspired sensing and energy storage materials, with special emphasis on the influence of interfacial interactions over their improved properties.

Predicting wavelength-dependent photochemical reactivity and selectivity

Predicting the conversion and selectivity of a photochemical experiment is a conceptually different challenge compared to thermally induced reactivity. Photochemical transformations do not currently have the same level of generalized analytical treatment due to the nature of light interaction with a photoreactive substrate. Herein, we bridge this critical gap by introducing a framework for the quantitative prediction of the time-dependent progress of photoreactions via common LEDs. A wavelength and concentration dependent reaction quantum yield map of a model photoligation, i.e., the reaction of thioether o-methylbenzaldehydes via o-quinodimethanes with N-ethylmaleimide, is initially determined with a tunable laser system. Combined with experimental parameters, the data are employed to predict LED-light induced conversion through a wavelength-resolved numerical simulation. The model is validated with experiments at varied wavelengths. Importantly, a second algorithm allows the assessment of competing photoreactions and enables the facile design of λ-orthogonal ligation systems based on substituted o-methylbenzaldehydes.

Oxide-based composites: applications in thermo-photocatalysis

Recent progress on oxide-based thermo-photocatalytic composite systems. Role of plasmonic, defect-related, and thermal effects on the catalytic performance.

Efficiencies Evaluation of Photocatalytic Paints Under Indoor and Outdoor Air Conditions

The removal of indoor and outdoor air pollutants is crucial to prevent environmental and health issues. Photocatalytic building materials are an energy-sustainable technology that can completely oxidize pollutants, improving in situ the air quality of contaminated sites. In this work, different photoactive TiO₂ catalysts (anatase or modified anatase) and amounts were used to formulate photocatalytic paints in replacement of the normally used TiO₂ (rutile) pigment. These paints were tested in two different experimental systems simulating indoor and outdoor environments. In one, indoor illumination conditions were used in the photoreactor for the oxidation of acetaldehyde achieving conversions between 37 and 55%. The other sets of experiments were performed under simulated outdoor radiation for the degradation of nitric oxide, resulting in conversions between 13 and 35%. This wide range of conversions made it difficult to directly compare the paints. Thus, absorption, photonic, and quantum efficiencies were calculated to account for the paints photocatalytic performance. It was found that the formulations containing carbon-doped TiO₂ presented the best efficiencies. The paint with the maximum amount of this photocatalyst showed the highest absorption and photonic efficiencies. On the other hand, the paint with the lowest amount of carbon-doped TiO₂ presented the highest value of quantum efficiency, thus becoming the optimal formulation in terms of energy use.

Synergistic Effects of Carbon Dots and Palladium Nanoparticles Enhance the Sonocatalytic Performance for Rhodamine B Degradation in the Absence of Light

Carbon dot (CD) and palladium nanoparticle (Pd NP) composites are semiconducting materials having tremendous applications in catalysis with suitable band gaps. However, their combination with a suitable polymer matrix in sonophotocatalysis has not been explored. Herein, we have synthesized and characterized a new nanohybrid catalyst from a polyamide cross-linked CD-polymer and subsequent deposition of Pd NPs. A sonocatalytic activity of 99% rhodamine B dye degradation was achieved in mere 5 min in the dark. A model catalyst replacing CDs with benzene and other control studies revealed that the synergistic effects of CDs and Pd NPs enhance the sonocatalytic activity of the nanohybrid catalyst. Interestingly, visible light did not influence the activity significantly. Mechanistic investigations suggest that generation of reactive oxygen species on the surface of the CD-polymer initiated by ultrasound, which is further facilitated by Pd NPs, is the key for remarkable catalytic activity (a rate constant of 0.99 min-1). Recyclable heterogeneous catalysts under ambient conditions are promising for exploring sono-assisted dark catalysis for several avenues.

Insights into Interface Charge Extraction in a Noble-Metal-Free Doped Z-Scheme NiO@BiOCl Heterojunction

It is of great significance to thoroughly explore the interface charge extraction and migration in heterojunction systems, which could guide us to synthesize higher-efficiency photocatalytic materials. A novel noble-metal-free doped Z-scheme NiO@BiOCl heterojunction was found in this work. The corresponding heterostructure, interface electron extraction, and electron migration were investigated via first-principles calculation. 5,5′-dimethyl-1-pyrroline-N-oxide (DMPO) spin-trapping electron spin resonance (ESR) and time-resolved photoluminescence (TRPL) tests were implemented to confirm the calculation results, which showed that electrons and holes stayed in the NiO (100) facet and BiOCl (110) facet, respectively. Owing to the large chemical potential of 2.40 V (vs ENHE) for the BiOCl valence-band hole, it possessed super activity to oxidize water into hydroxyl radicals or molecular oxygen. We hope this promising multifunctional photocatalytic material, therefore, NiO@BiOCl can be applied in advanced treatment of organic wastewater and oxygen production from photolysis water.

Olive Leaves as Biotemplates for Enhanced Solar-Light Harvesting by a Titania-Based Solid

Olive leaves (by-product from olive oil production in olive mills) were used as biotemplates to synthesize a titania-based artificial olive leaf (AOL). Scanning electron microscopy (SEM) images of AOL showed the successful replication of trichomes and internal structure channels present in olive leaves. The BET surface area of AOL was 52 m²·g^-1. X-ray diffraction (XRD) and Raman spectra revealed that the resulting solid was in the predominantly-anatase crystalline form (7.5 nm average particle size). Moreover, the synthesis led to a red-shift in light absorption as compared to reference anatase (gap energies of 2.98 and 3.2 eV, respectively). The presence of surface defects (as evidenced by X-ray photoelectron spectroscopy, XPS, and electron paramagnetic resonance spectroscopy, EPR) and doping elements (e.g., 1% nitrogen, observed by elemental analysis and XPS) could account for that. AOL was preliminarily tested as a catalyst for hydrogen production through glycerol photoreforming and exhibited an activity 64% higher than reference material Evonik P25 under solar irradiation and 144% greater under ultraviolet radiation, (under voltage) UV.

Synthesis, phase transformation, and morphology of hausmannite Mn3O4 nanoparticles: photocatalytic and antibacterial investigations

Nano structured Hausmannite (Mn₃O₄) has efficacious applications in numerous fields, such as catalytic, medical, biosensors, waste water remediation, energy storage devices etc. The potential application in wastewater treatment is due to its distinct structural features combined with fascinating physicochemical properties. Another area of interest is the oxidative properties imparted due to its reduction potential. Larger surface to volume ratio and high reactivity than the bulk form shows great progress as antimicrobial agent to control drug resistant microbial population. The distinct surface morphologies, crystalline forms, reaction conditions and synthetic methods exerts significant impact on the photo catalytic and bactericidal efficiency. Hence, the present paper focuses on a concise review of the multifarious study on synthetic methods of Mn₃O₄, growth mechanisms, structural forms, phase transformation and phase control, shape and dimensionality. The review also confers its applications towards photo catalytic and bactericidal studies.

Assessment of an intrinsic kinetic model for TiO2–formic acid photodegradation using LEDs as a radiation source

Intrinsic kinetic parameters for two photocatalysts, one of them modified with carbon, were estimated to model HCOOH photodegradation using LEDs with different emission spectra.

Process analytical technology (PAT) as a versatile tool for real-time monitoring and kinetic evaluation of photocatalytic reactions

Combining in situ Raman spectroscopy with multivariate data analysis enables the real-time monitoring and kinetic evaluation of photocatalytic reactions. The applicability is demonstrated on the photooxidation of 4-methoxythiophenol.

Photocatalytic toluene degradation: braiding physico-chemical and intrinsic kinetic analyses

Combined physico-chemical and kinetic analyses of photo-catalytic elimination reactions for quantitative understanding.

Waste-derived Materials: Opportunities in Photocatalysis

Waste-derived materials have been gaining increased attention in recent years due to their great potential and environmentally friendly nature. Several contributions in the literature have covered the advances achieved so far in this area. Nonetheless, to the best of our knowledge, no review has been dedicated specifically to waste-derived or templated photocatalytic materials. Both photocatalysis and (bio)waste-inspired design yield materials of a remarkably green nature. Therefore, the partnership between them may open promising possibilities for both waste valorization and photocatalytic processes, which in turn will lead to sustainable development globally, with the potential for full utilization of renewable energy sources such as biomass and sunlight. Several photocatalytic waste-derived materials, synthetic procedures, and applications will be described throughout this work, including waste-derived/templated TiO₂, ZnO, and metal sulfide materials. Special attention will be given to biomass-inspired carbonaceous materials, including carbon quantum dots and graphitic carbon nitride (g-C₃N₄).

Facile Fabrication of Flower-Like BiOI/BiOCOOH p-n Heterojunctions for Highly Efficient Visible-Light-Driven Photocatalytic Removal of Harmful Antibiotics

Novel heterojunction photocatalysts with remarkable photocatalytic capabilities and durability for degrading recalcitrant contaminants are extremely desired; however, their development still remains quite challenging. In this study, a series of flower-like BiOI/BiOCOOH p–n heterojunctions were fabricated via a controlled in situ anion-exchange process. During the process, BiOI formation and even deposition on BiOCOOH microspheres with tight interfacial contact were realized. As expected, BiOI/BiOCOOH heterojunctions revealed remarkable enhancements in photocatalytic antibiotic degradation capacities under visible light irradiation compared with pristine BiOI and BiOCOOH. The best-performing BiOI/BiOCOOH heterojunction (i.e., IBOCH-2) showed much improved photocatalytic CIP degradation efficiency of approximately 81- and 3.9-fold greater than those of bare BiOI and BiOCOOH, respectively. The eminent photocatalytic performances were due not only to the enhanced capability in harvesting photon energies in visible light regions, but also the accelerated separation of electrons and holes boosted by the p–n heterojunction. Active species trapping tests demonstrated that superoxide free radicals (•O₂⁻) and photo-generated holes (h⁺) were major active species for CIP degradation. Recycling experiments verified the good durability of BIBO-2 over four runs. The facile in situ synthesis route and excellent performance endow flower-like BiOI/BiOCOOH heterojunctions with a promising potential for actual environmental remediation.

Characterization of Photo-catalysts: From Traditional to Advanced Approaches

The article provides an overview of the most relevant characterization results of heterogeneous photo-catalytic materials available in the literature. First, we present a summary of the ex situ utilization of physico-chemical characterization techniques. In the majority of current works, pre and post-reaction samples are subjected to ex situ analysis using a multitechnique approach which attempts to render information about the morphological, structural, and electronic properties of relevance to interpret photoactivity. Details of the effects on physico-chemical observables of the nanostructure and the complex chemical nature (considering mono and multiphase materials with presence of several chemical elements) of typical photo-catalysts will be analyzed. Modern studies however emphasize the use of in situ tools in order to establish activity-structure links. To this end, the first point to pay attention to is to consider carefully the interaction between light and matter at the reaction cell where the characterization is carried out. Operando and spectro-kinetic methodologies will be reviewed as they would render valuable and trusting results and thus will pave the way for the future developments in photocatalysis.

Kinetics and Optimization of the Photocatalytic Reduction of Nitrobenzene

The photocatalytic reduction of nitrobenzene to aniline in alcoholic solutions appears as an interesting alternative to the classical hydration. However, little is known about the influence of reaction parameters on the kinetics of the reaction which were therefore studied herein. The effects of light intensity, catalyst concentration, initial concentration, and temperature were systematically investigated under more than 50 different conditions and accurately described with an appropriate kinetic model. The results show that the efficiency of the reaction is extremely high and apparent quantum yields of up to 142 % were observed under optimized conditions. Particularly interesting is the fact high efficiencies were also obtained at high reaction rates of up to 74.3 mM h-1. Overall these results demonstrate that heterogeneous photocatalytic reactions can be very efficient and productive at the same time and may therefore present a powerful tool in synthetic organic chemistry.

Metal/Semiconductor Nanocomposites for Photocatalysis: Fundamentals, Structures, Applications and Properties

Due to the capability of utilizing light energy to drive chemical reactions, photocatalysis has been widely accepted as a green technology to help us address the increasingly severe environment and energy issues facing human society. To date, a large amount of research has been devoted to enhancing the properties of photocatalysts. As reported, coupling semiconductors with metals is one of the most effective methods to achieve high-performance photocatalysts. The excellent properties of metal/semiconductor (M/S) nanocomposite photocatalysts originate in two aspects: (i) improved charge separation at the metal-semiconductor interface; and (ii) increased absorption of visible light due to the surface plasmon resonance of metals. So far, many M/S nanocomposite photocatalysts with different structures have been developed for the application in environmental remediation, selective organic transformation, hydrogen evolution, and disinfection. Herein, we will give a review on the M/S nanocomposite photocatalysts, regarding their fundamentals, structures (as well as their typical synthetic approaches), applications and properties. Finally, we will also present our perspective on the future development of M/S nanocomposite photocatalysts.