Recent progress and challenges in solution blow spinning

Characterization of Blow-Spun Polyurethane Scaffolds-Influence of Fiber Alignment and Fiber Diameter on Pericyte Growth

In this study, fibrous polyurethane (PU) materials with average fiber diameter of 200, 500, and 1000 nm were produced using a solution blow spinning (SBS) process. The effects of the rotation speed of the collector (in the range of 200-25 000 rpm) on the fiber alignment and diameter were investigated. The results showed that fiber alignment was influenced by the rotation speed of the collector, and such alignment was possible when the fiber diameter was within a specific range. Homogeneously oriented fibers were obtained only for a fiber diameter ≥500 nm. Moreover, the changes in fiber orientation and fiber diameter (resulting from changes in the rotation speed of the collector) were more noticeable for materials with an average fiber diameter of 1000 nm in comparison to 500 nm, which suggests that the larger the fiber diameter, the better the controlled architectures that can be obtained. The porosity of the produced scaffolds was about 65-70%, except for materials with a fiber diameter of 1000 nm and aligned fibers, which had a higher porosity (76%). Thus, the scaffold pore size increased with increasing fiber diameter but decreased with increasing fiber alignment. The mechanical properties of fibrous materials strongly depend on the direction of stretching, whereby the fiber orientation influences the mechanical strength only for materials with a fiber diameter of 1000 nm. Furthermore, the fiber diameter and alignment affected the pericyte growth. Significant differences in cell growth were observed after 7 days of cell culture between materials with a fiber diameter of 1000 nm (cell coverage 96-99%) and those with a fiber diameter of 500 nm (cell coverage 70-90%). By appropriately setting the SBS process parameters, scaffolds can be easily adapted to the cell requirements, which is of great importance in producing complex 3D structures for guided tissue regeneration.

Nonwoven fiber meshes for oxygen sensing

Accurate oxygen sensing and cost-effective fabrication are crucial for the adoption of wearable devices inside and outside the clinical setting. Here we introduce a simple strategy to create nonwoven polymeric fibrous mats for a notable contribution towards addressing this need. Although morphological manipulation of polymers for cell culture proliferation is commonplace, especially in the field of regenerative medicine, non-woven structures have not been used for oxygen sensing. We used an airbrush spraying, i.e. solution blowing, to obtain nonwoven fiber meshes embedded with a phosphorescent dye. The fibers serve as a polymer host for the phosphorescent dye and are shown to be non-cytotoxic. Different composite fibrous meshes were prepared and favorable mechanical and oxygen-sensing properties were demonstrated. A Young's modulus of 9.8 MPa was achieved and the maximum oxygen sensitivity improved by a factor of ∼2.9 compared to simple drop cast film. The fibers were also coated with silicone rubbers to produce mechanically robust sensing films. This reduced the sensing performance but improved flexibility and mechanical properties. Lastly, we are able to capture oxygen concentration maps via colorimetry using a smartphone camera, which should offer unique advantages in wider usage. Overall, the introduced composite fiber meshes show a potential to significantly improve cell cultures and healthcare monitoring via absolute oxygen sensing.

Numerical Analysis of the Airflow Field and Experiments of Fiber Motion for Solution Blowing

Solution blowing is a rapidly developing technology for the rapid and large-scale preparation of nanofibers, driven by its advantages, such as wide adaptability to raw materials, simple and safe operation, and ease of scalable production. Most of the research related to solution blowing mainly focuses on the fiber spinning and forming principle, fiber structure and properties, and the development of new materials. Limited studies have focused on the airflow field and fiber motion in solution blowing. In this paper, nine nozzles for solution blowing with varying geometrical parameters were designed by adjusting the outer nozzle diameter, inner nozzle outstretched distance, and inner nozzle diameter. The centerline airflow velocity, turbulence intensity, and velocity distribution of the solution blowing were analyzed using the numerical simulation method. The results showed that the outer nozzle diameter had the greatest influence on the air velocity and turbulence intensity. The airflow velocity increased and the turbulence intensity decreased with the increase of the outer nozzle diameter. The inner nozzle outstretched distance only affected the airflow convergence point and had less effect on the airflow velocity and turbulence intensity. The captured trajectory of the polymer jet initially shows a straight or slightly curved development that eventually diverges from the airflow field. With an increasing distance, dispersed fibers exhibit instability, including loop formation, bonding, and separation. The experimental observation of fiber morphology in the solution-blowing web further verified the instability during the fiber movement.

Spinning the Future: The Convergence of Nanofiber Technologies and Yarn Fabrication

The rapid advancement in nanofiber technologies has revolutionized the domain of yarn materials, marking a significant leap in textile technology. This review dissects the nexus between cutting-edge nanofiber technologies and yarn manufacturing, aiming to illuminate the pathway toward engineering advanced textiles with unparalleled functionality. It first discusses the fundamentals of nanofiber assemblies and spinning techniques, primarily focusing on electrospinning, centrifugal spinning, and blow spinning. Additionally, the study delves into integrating nanofiber spinning technologies with traditional and modern yarn fabrication principles, elucidating the design principles that underlie the creation of yarns incorporating nanofibers. Twisting technologies are explored to examine how they can be optimized and adapted for incorporating nanofibers, thus enabling the production of innovative nanofiber-based yarns. Special attention is given to scalable strategies like centrifugal and blow spinning, which are spotlighted for their efficiency and scalability in fabricating nanofiber yarns. This review further analyses recently developed nanofiber yarn applications, including wearable sensors, biomedical devices, moisture management textiles, and energy harvesting and storage devices. We finally present a forward-looking perspective to address unresolved issues in nanofiber-based yarn technologies.

Maturation of human cardiomyocytes derived from induced pluripotent stem cells (iPSC-CMs) on polycaprolactone and polyurethane nanofibrous mats

Investigating the potential of human cardiomyocytes derived from induced pluripotent stem cells (iPSC-CMs) in in vitro heart models is essential to develop cardiac regenerative medicine. iPSC-CMs are immature with a fetal-like phenotype relative to cardiomyocytes in vivo. Literature indicates methods for enhancing the structural maturity of iPSC-CMs. Among these strategies, nanofibrous scaffolds offer more accurate mimicry of the functioning of cardiac tissue structures in the human body. However, further research is needed on the use of nanofibrous mats to understand their effects on iPSC-CMs. Our research aimed to evaluate the suitability of poly(ε-caprolactone) (PCL) and polyurethane (PU) nanofibrous mats with different elasticities as materials for the maturation of iPSC-CMs. Analysis of cell morphology and orientation and the expression levels of selected genes and proteins were performed to determine the effect of the type of nanofibrous mats on the maturation of iPSC-CMs after long-term (10-day) culture. Understanding the impact of 3D structural properties in in vitro cardiac models on induced pluripotent stem cell-derived cardiomyocyte maturation is crucial for advancing cardiac tissue engineering and regenerative medicine because it can help optimize conditions for obtaining more mature and functional human cardiomyocytes.

Recent advances in photoresponsive printing inks for security encoding applications

Counterfeiting of banknotes, important documents, and branded goods continues to be a major worldwide problem for governments, businesses, and consumers. This problem has serious financial, security, and health implications. Due to their stability for printing on various substrates, the photochromic anticounterfeiting inks have received important interest. There have been various photochromic agents, such as polymer nanoparticles, quantum and carbon dots, and organic and inorganic fluorophores and luminophores, which have been broadly used for antiforging applications. In comparison to organic agents, inorganic photochromic materials have better stability under reversible/long-term light illumination. Recently, the remarkable optical characteristics and chemical stability of photoluminescent and photochromic agents have led to their extensive usage anticounterfeiting products. There have been also several strategies to tackle the rising problem of counterfeiting. Both of solvent-based and water-based inks have been developed for security encoding purposes. Additionally, the printing methods, including screen printing, labeling, stamping, inkjet printing, and handwriting, that have been used to apply anticounterfeiting inks onto various surfaces are discussed. The limitations of photoluminescent and photochromic agents and the potential for their future preparation to combat counterfeiting were discussed. This review would benefit academic researchers and industrial developers who are interested in the area of security printing.

In vitro and in vivo assessment of curcumin-quercetin loaded multi-layered 3D-nanofibroporous matrix prepared by solution blow-spinning for full-thickness burn wound healing

Burn wounds (BWs) cause impairment of native skin tissue and may cause significant microbial infections that demand immediate care. Curcumin (Cur) and quercetin (Que) exhibit antimicrobial, hemocompatibility, ROS-scavenging, and anti-inflammatory properties. However, its instability, water insolubility, and low biological fluid absorption render it challenging to sustain local Cur and Que doses at the wound site. Therefore, to combat these limitations, we employed blow-spinning and freeze-drying to develop a multi-layered, Cur/Que-loaded gelatin/chitosan/PCL (GCP-Q/C) nanofibroporous (NFP) matrix. Morphological analysis of the NFP-matrix using SEM revealed a well-formed multi-layered structure. The FTIR and XRD plots demonstrated dual-bioactive incorporation and scaffold polymer interaction. Additionally, the GCP-Q/C matrix displayed high porosity (82.7 ± 2.07 %), adequate pore size (∼121 μm), enhanced water-uptake ability (∼675 % within 24 h), and satisfactory biodegradation. The scaffolds with bioactives had a long-term release, increased antioxidant activity, and were more effective against gram-positive (S. aureus) and gram-negative (E. coli) bacteria than the unloaded scaffolds. The in vitro findings of GCP-Q/C scaffolds showed promoted L929 cell growth and hemocompatibility. Additionally, an in vivo full-thickness BW investigation found that an implanted GCP-Q/C matrix stimulates rapid recuperation and tissue regeneration. In accordance with the findings, the Gel/Ch/PCL-Que/Cur NFP-matrix could represent an effective wound-healing dressing for BWs.

Automatic in situ short-distance deposition of PLGA/PLLA composite nanofibrous membranes for personalized wound dressings

Improving the mechanical properties of wound dressings and achieving personalized automatic real-time in situ deposition are important for accelerating wound management and repair. In this study, we report a self-designed automatic in situ deposition device based on solution blow spinning (SBS) to prepare poly(lactic-co-glycolic acid) (PLGA) and poly-L-lactic acid (PLLA) composite (PLGA/PLLA) nanofibrous membranes for wound dressing at a short distance. Polymer solution and in situ deposition conditions, including air pressure, spinning distance, solvent extrusion rate, and spinning rate, were optimized using orthogonal experiments and characterized via dynamic mechanical analysis. The microscopic morphology and physical properties of the prepared PLGA/PLLA composite nanofibrous membranes show that their strength, adhesion, water vapor transmission rate (WVTR), water retention, water absorption, degradation, and other properties were sufficient for wound-dressing applications. To investigate the possibility of a biomedical wound-dressing material, tannic acid (TA) was incorporated into the PLGA/PLLA composite nanofibrous membranes. The resultant PLGA/PLLA/TA composite nanofibrous membranes exhibited good biocompatibility and exceptional antibacterial properties against both Escherichia coli and Staphylococcus aureus. A pilot animal study illustrated the potential of this in situ deposition of PLGA/PLLA/TA composite nanofibrous membranes across multiple applications in wound healing/repair by reducing wound scar tissue formation and fibroblast overactivation.

Review: 3D cell models for organ-on-a-chip applications

Two-dimensional (2D) cultures do not fully reflect the human organs' physiology and the real effectiveness of the used therapy. Therefore, three-dimensional (3D) models are increasingly used in bioanalytical science. Organ-on-a-chip systems are used to obtain cellular in vitro models, better reflecting the human body's in vivo characteristics and allowing us to obtain more reliable results than standard preclinical models. Such 3D models can be used to understand the behavior of tissues/organs in response to selected biophysical and biochemical factors, pathological conditions (the mechanisms of their formation), drug screening, or inter-organ interactions. This review characterizes 3D models obtained in microfluidic systems. These include spheroids/aggregates, hydrogel cultures, multilayers, organoids, or cultures on biomaterials. Next, the methods of formation of different 3D cultures in Organ-on-a-chip systems are presented, and examples of such Organ-on-a-chip systems are discussed. Finally, current applications of 3D cell-on-a-chip systems and future perspectives are covered.

Gas-Blows-Liquid Spinning Strategy Toward Mechanically Strong, Thermally Protective, Efficiently Hemostatic Aerogel Fibers/Fabrics

Nanoporous aerogel fibers enjoy the luxury of being one of the most attractive nanomaterials. However, the representative fabrication pathways have faced up with low production rates due to significant speed mismatch between slow sol-gel transition and as fast as possible spinning in the same period. Herein, a novel gas-blows-liquid spinning (GS) strategy with a spinning speed of 300-700 m s-1 is developed to get the high-speed and high-efficiency production of aerogel fibers/fabrics. The spinning speed of the GS strategy is 900 times higher than various techniques reported for aerogel fibers. The resulting aerogel fibers exhibit a high specific surface area (180 m2 g-1). In comparison, the aerogel fiber possesses the highest tensile strength (58.7±3.9 MPa) among its counterparts and aerogel fabric with surprising water-absorption and microparticle-blocking performances exhibits the application prospect for better hemostasis than that of commercial gauze and cotton ball. Besides, the GS aerogel fabrics with hierarchical aligned structures show better thermal insulation (≈0.035 Wm-1K-1) than wet spinning aerogel fabric and commercial insulation felts. This work has provided inspiration for fast fabricating more aerogel fibers/fabrics with this GS strategy, and the resulting aerogel fibers/fabrics may find significant application in the fields of 5G smart phones, wound hemostasis, etc.

Pullulan nanofibrous films incorporated with W/O emulsions via microfluidic solution blow spinning technology

In this work, pullulan (PUL) nanofibrous films incorporated with water-in-oil emulsions (PE) were prepared by microfluidic blowing spinning (MBS). The microstructures of nanofibers were characterized by scanning electron microscopy (SEM), fourier transform infrared (FT-IR), and X-ray diffraction (XRD). With the addition of W/O emulsions, the thermal stability, mechanical, and water barrier properties of PUL nanofibers were improved. Increases in emulsion content significantly affected the antioxidant and antimicrobial properties of nanofibrous films. ABTS and DPPH free radical scavenging rates increased from 10.26 % and 8.57 % to 60.66 % and 57.54 %, respectively. The inhibition zone of PE nanofibers against E. coli and S. aureus increased from 11.00 to 20.00 and from 15.67 to 21.17 mm, respectively. In addition, we investigated the freshness effectiveness of PE nanofibrous films on fresh-cut apples. PE nanofibrous films significantly maintained the firmness, and reduced the weight loss and browning index of the fresh-cut apple, throughout the 4 days of storage. Thus, the PE nanofibrous films exhibited good potential to prolong the shelf life of fresh-cut fruit and promote the development of active food packaging.

Electrospinning and electrospun polysaccharide-based nanofiber membranes: A review

The electrospinning technology has set off a tide and given rise to the attention of a widespread range of research territories, benefiting from the enhancement of nanofibers which made a spurt of progress. Nanofibers, continuously produced via electrospinning technology, have greater specific surface area and higher porosity and play a non-substitutable key role in many fields. Combined with the degradability and compatibility of the natural structure characteristics of polysaccharides, electrospun polysaccharide nanofiber membranes gradually infiltrate into the life field to help filter air contamination particles and water pollutants, treat wounds, keep food fresh, monitor electronic equipment, etc., thus improving the life quality. Compared with the evaluation of polysaccharide-based nanofiber membranes in a specific field, this paper comprehensively summarized the existing electrospinning technology and focused on the latest research progress about the application of polysaccharide-based nanofiber in different fields, represented by starch, chitosan, and cellulose. Finally, the benefits and defects of electrospun are discussed in brief, and the prospects for broadening the application of polysaccharide nanofiber membranes are presented for the glorious expectation dedicated to the progress of the eras.

Carboxymethyl chitosan and polycaprolactone-based rapid in-situ packaging for fruit preservation by solution blow spinning

Nanofiber packaging has not yet gained practical application in fruit preservation because of some limitations, such as low production rate and utilization, and failure due to poor adhesion to the fruit. Herein, to solve this issue, a novel fruit packaging method based on solution blow spinning (SBS), called in-situ packaging, was pioneered. Specifically, carboxymethyl chitosan (CMCH) and polycaprolactone (PCL) were chosen as substrate materials and cherry tomatoes were selected as demonstration subjects. CMCH/PCL nanofibers were deposited directly onto the surface of cherry tomatoes by SBS, forming a tightly adherent and stable fiber coating in 8 min. Also, this in-situ packaging could be easily peeled off by hand. The in-situ packaging was an excellent carrier for active substances and was effective in inhibiting gray mold on cherry tomatoes. The in-situ packaging film formed a barrier on the surface of cherry tomatoes to limit moisture penetration, resulting in reduced respiration of fruits, which led to reduced weight and firmness loss. In addition, metabolomics and color analysis revealed that the in-situ packaging delayed ripening of cherry tomatoes after harvest. Overall, the in-situ packaging method developed in the present work provides a new solution for post-harvest fruit preservation.

Multi-needle blow-spinning technique for fabricating collagen nanofibrous nerve guidance conduit with scalable productivity and high performance

Nerve guidance conduits (NGCs) have been widely accepted as a promising strategy for peripheral nerve regeneration. Fabricating ideal NGCs with good biocompatibility, biodegradability, permeability, appropriate mechanical properties (space maintenance, suturing performance, etc.), and oriented topographic cues is still current research focus. From the perspective of translation, the technique stability and scalability are also an important consideration for industrial production. Recently, blow-spinning technique shows great potentials in nanofibrous scaffolds fabrication, possessing high quality, high fiber production rates, low cost, ease of maintenance, and high reliability. In this study, we proposed for the first time the preparation of a novel NGC via blow-spinning technique to obtain optimized performances and high productivity. A new collagen nanofibrous neuro-tube with the bilayered design was developed, incorporating inner oriented and outer random topographical cues. The bilayer structure enhances the mechanical properties of the conduit in dry and wet, displaying good radial support and suturing performance. The porous nature of the blow-spun collagen membrane enables good nutrient delivery and metabolism. The in vitro and in vivo evaluations indicated the bilayer-structure conduit could promoted Schwann cells growth, neurotrophic factors secretion, and axonal regeneration and motor functional recovery in rat.

"Nano in Nano"-Incorporation of ZnO Nanoparticles into Cellulose Acetate-Poly(Ethylene Oxide) Composite Nanofibers Using Solution Blow Spinning

In this work, the preparation and characterization of composites from cellulose acetate (CA)-poly(ethylene oxide) (PEO) nanofibers (NFs) with incorporated zinc oxide nanoparticles (ZnO-NPs) using solution blow spinning (SBS) is reported. CA-PEO nanofibers were produced by spinning solution that contained a higher CA-to-PEO ratio and lower (equal) CA-to-PEO ratio. Nanoparticles were added to comprise 2.5% and 5% of the solution, calculated on the weight of the polymers. To have better control of the SBS processing conditions, characterization of the spinning suspensions is carried out, which reveals a decrease in viscosity (two- to eightfold) upon the addition of NPs. It is observed that this variation of viscosity does not significantly affect the mean diameters of nanofibers, but does affect the mode of the nanofibers' size distribution, whereby lower viscosity provides thinner fibers. FESEM-EDS confirms ZnO NP encapsulation into nanofibers, specifically into the CA component based on UV-vis studies, since the release of ZnO is not detected for up to 5 days in deionized water, despite the significant swelling of the material and accompanied dissolution of water-soluble PEO. Upon the dissolution of CA nanofibers into acetone, immediate release of ZnO is detected, both visually and by spectrometer. ATR-FTIR studies reveal interaction of ZnO with the CA component of composite nanofibers. As ZnO nanoparticles are known for their bioactivity, it can be concluded that these CA-PEO-ZnO composites are good candidates to be used in filtration membranes, with no loss of incorporated ZnO NPs or their release into an environment.

Rapid fabrication of micro-nanofibers from grapevine leaf extract and gelatine via electroblowing: A novel approach for edible active food packaging

The objective of this study was to develop novel micro-nanofibers for food packaging using grapevine extract (GLP) and gelatine using electroblowing technique. The identified components of GLP were dominated by the flavone group phenolics, as analyzed by LC-MS/MS. SBS was used to fabricate gelatine micro-nanofiber mats loaded with three different concentrations of GLP, which were subsequently cross-linked. The micro-nanofibers were characterized by their morphology, chemistry, thermal properties, and bioactivity. The in-vitro antioxidant and antimicrobial effects of the nanofiber mats were determined using various methods, which showed an increase in effectiveness with increasing GLP concentration. The in-situ assessment, where the nanofibers were applied to cheese, also showed a consistent improvement in shelf life with the use of GLP-loaded gelatin electroblown fibers.

Natamycin-Loaded Ethyl Cellulose/PVP Films Developed by Microfluidic Spinning for Active Packaging

The preparation of active packaging loaded with antimicrobial, antioxidant, and other functional agents has become a hot topic for food preservation in recent years. In this field, active fiber films based on spinning methods have attracted the interest of researchers owing to their high specific surface area, high porosity, high loading capacity, and good controlled release capacity. In the present work, neatly arranged ethyl cellulose (EC)/polyvinyl-pyrrolidone (PVP) fibrous films loaded with natamycin as an antimicrobial agent were prepared by microfluidic spinning. The encapsulation efficiency of natamycin was more than 90% in each group and the loading increased with increasing natamycin content. According to the characterization results of the natamycin-loaded EC/PVP fibrous films, hydrogen bonding was formed between natamycin and EC and PVP in the fibrous films. Meanwhile, the water contact angle of the fibrous films was increased, suggesting the improved hydrophobicity of the films. In the in vitro bacterial inhibition experiments, the active fiber films loaded with natamycin showed good antimicrobial activity, which could significantly inhibit the growth of gray mold. In conclusion, N-EC/PVP fibrous films with antimicrobial activity prepared by microfluidic spinning showed good potential in the field of active packaging.

Fibrous Structures Produced Using the Solution Blow-Spinning Technique for Advanced Air Filtration Process

This study proposes utilising the solution blow-spinning process (SBS) for manufacturing a biodegradable filtration structure that ensures high efficiency of particle filtration with an acceptable pressure drop. The concept of multi-layer filters was applied during the design of filters. Polylactic acid (PLA) was used to produce various layers, which may be mixed in different sequences, building structures with varying filtration properties. Changing the process parameters, one can create layers with diverse average fibre diameters and thicknesses. It enables the design and creation of optimal filtration materials prepared for aerosol particle filtration. The structures were numerically modelled using the lattice Boltzmann approach to obtain detailed production guidelines using the blow-spinning technique. The advantage of this method is the ability to blow fibres with diameters in the nanoscale, applying relatively simple and cost-effective equipment. For tested PLA solutions, i.e., 6% and 10%, the mean fibre diameter decreases as the concentration decreases. Therefore, the overall filtering efficiency decreases as the concentration of the used solution increases. The produced multi-layer filters have 96% overall filtration efficiency for particles ranging from 0.26 to 16.60 micrometres with a pressure drop of less than 160 Pa. Obtained results are auspicious and are a step in producing efficient, biodegradable air filters.

Enhancement of integrated nano-sensor performance comprised of electrospun PANI/carbonaceous material fibers for phenolic detection in aqueous solutions

The detection of trace levels of organic residue in water samples is a key health issue. This manuscript describes the fabrication of integrated nano-sensors composed of electrospun microfibers consisting of a nanocomposite of carbonaceous materials (CNMs) containing polyaniline (PANI) and polycaprolactone (PCL) for phenolic detection in aqueous solutions. The morphology of the resulting microfiber composite was characterized by scanning electron microscopy. It revealed elongated fibers with a highly interconnected web-like pattern in the presence of reduced graphene oxide (rGO). Shorter microfibers were observed in the composite filled with multi-walled carbon nanotubes (MWCNTs), whereas large agglomerates were formed upon the incorporation of single-walled CNTs (SWCNTs) and graphene 300 (G300). Comparative analysis showed that the PANI/CNM sensors exhibited the best electrochemical properties, in particular in the presence of rGO and MWCNTs, where greater electrical conductivity was achieved, i.e., 4.33 × 10-3 and 7.22 × 10-4 S/cm, respectively, as compared to the PANI-PCL sensor (3.79 × 10-4 S/cm). All the PANI/CNM sensors exhibited high sensitivity. Notably, PANI/rGO was found to have a detection limit of 8.34 × 10-3 µM for aminophenol. All the sensors exhibited good selectivity in the presence of interference to detecting phenolic compounds in aqueous solutions, thus confirming their value for industrial applications.

HE@PCL/PCE Gel-Nanofiber Dressing with Robust Self-Adhesion toward High Wound-Healing Rate via Microfluidic Electrospinning Technology

Hydrogels have attracted increasing attention in the biomedical field due to their similarity in structure and composition to natural extracellular matrices. However, they have been greatly limited by their low mechanical strength and self-adhesion for further application. Here, a gel-nanofiber material is designed for wound healing, which synergistically combines the benefits of hydrogels and nanofibers and can overcome the bottleneck of poor mechanical strength and self-adhesion in hydrogels and inadequate healing environment created by nanofibers. First, a nanofiber scaffold composed of polycaprolactone/poly(citric acid)-ε-lysine (PCL/PCE) nanofibers is fabricated via a new strategy of microfluidic electrospinning, which could provide a base for hyaluronic acid-polylysine (HE) gel growth on nanofibers. The prepared HE@PCL/PCE gel-nanofiber possesses high tensile strength (24.15 ± 1.67 MPa), excellent air permeability (656 m3/m2 h kPa), outstanding self-adhesion property, and positive hydrophilicity. More importantly, the prepared gel-nanofiber dressing shows good cytocompatibility and antibacterial properties, achieving a high wound-healing rate (92.48%) and 4.685 mm granulation growth thickness within 12 days. This material may open a promising avenue for accelerating wound healing and tissue regeneration, providing potential applications in clinical medicine.

Evaluation of polycaprolactone nanofibers' spinnability using green solvent systems by solution blow spinning (SBS)

Solution blow spinning (SBS) is a promising alternative to produce fibrous matrices for a wide range of applications, such as packaging and biomedical devices. Polycaprolactone (PCL) is a biodegradable polyester commonly used for spinning. The usual choices for producing PCL solutions include chlorinated solvents (CS), such as chloroform. However, the high toxicity of CS makes it difficult for biological and green applications. This work evaluates the influence of two less toxic solvents, acetic acid (AA) and acetone (Acet), and their mixtures (AA/Acet) on the properties of PCL fibers produced by SBS. The results showed that Acet does not cause degradation of the PCL chains, in opposition to AA. Furthermore, adding acetone to the acetic acid tended to preserve the size of PCL chains. It was not possible to produce fibers using PCL in 100% acetone. However, the AA/Acet mixture allowed the efficient production of PCL fibers. The proportion of Acet and AA in the mixture modulated the fiber morphology and orientation, making it possible to use this green solvent system according to the desired application.

Advances in Biomedical Applications of Solution Blow Spinning

In recent years, Solution Blow Spinning (SBS) has emerged as a new technology for the production of polymeric, nanocomposite, and ceramic materials in the form of nano and microfibers, with similar features to those achieved by other procedures. The advantages of SBS over other spinning methods are the fast generation of fibers and the simplicity of the experimental setup that opens up the possibility of their on-site production. While producing a large number of nanofibers in a short time is a crucial factor in large-scale manufacturing, in situ generation, for example, in the form of sprayable, multifunctional dressings, capable of releasing embedded active agents on wounded tissue, or their use in operating rooms to prevent hemostasis during surgical interventions, open a wide range of possibilities. The interest in this spinning technology is evident from the growing number of patents issued and articles published over the last few years. Our focus in this review is on the biomedicine-oriented applications of SBS for the production of nanofibers based on the collection of the most relevant scientific papers published to date. Drug delivery, 3D culturing, regenerative medicine, and fabrication of biosensors are some of the areas in which SBS has been explored, most frequently at the proof-of-concept level. The promising results obtained demonstrate the potential of this technology in the biomedical and pharmaceutical fields.

Natural and Synthetic Polymeric Biomaterials for Application in Wound Management

Biomaterials are at the forefront of the future, finding a variety of applications in the biomedical field, especially in wound healing, thanks to their biocompatible and biodegradable properties. Wounds spontaneously try to heal through a series of interconnected processes involving several initiators and mediators such as cytokines, macrophages, and fibroblasts. The combination of biopolymers with wound healing properties may provide opportunities to synthesize matrices that stimulate and trigger target cell responses crucial to the healing process. This review outlines the optimal management and care required for wound treatment with a special focus on biopolymers, drug-delivery systems, and nanotechnologies used for enhanced wound healing applications. Researchers have utilized a range of techniques to produce wound dressings, leading to products with different characteristics. Each method comes with its unique strengths and limitations, which are important to consider. The future trajectory in wound dressing advancement should prioritize economical and eco-friendly methodologies, along with improving the efficacy of constituent materials. The aim of this work is to give researchers the possibility to evaluate the proper materials for wound dressing preparation and to better understand the optimal synthesis conditions as well as the most effective bioactive molecules to load.

Alumina Ceramic Nanofibers: An Overview of the Spinning Gel Preparation, Manufacturing Process, and Application

As an important inorganic material, alumina ceramic nanofibers have attracted more and more attention because of their excellent thermal stability, high melting point, low thermal conductivity, and good chemical stability. In this paper, the preparation conditions for alumina spinning gel, such as the experimental raw materials, spin finish aid, aging time, and so on, are briefly introduced. Then, various methods for preparing the alumina ceramic nanofibers are described, such as electrospinning, solution blow spinning, centrifugal spinning, and some other preparation processes. In addition, the application of alumina ceramic nanofibers in thermal insulation, high-temperature filtration, catalysis, energy storage, water restoration, sound absorption, bioengineering, and other fields are described. The wide application prospect of alumina ceramic nanofibers highlights its potential as an advanced functional material with various applications. This paper aims to provide readers with valuable insights into the design of alumina ceramic nanofibers and to explore their potential applications, contributing to the advancement of various technologies in the fields of energy, environment, and materials science.

Polyvinyl Alcohol Nanofibers Blends as Drug Delivery System in Tissue Regeneration

Nanofibers have shown promising clinical results in the process of tissue regeneration since they provide a similar structure to the extracellular matrix of different tissues, high surface-to-volume ratio and porosity, flexibility, and gas permeation, offering topographical features that stimulate cell adhesion and proliferation. Electrospinning is one of the most used techniques for manufacturing nanomaterials due to its simplicity and low cost. In this review, we highlight the use of nanofibers produced with polyvinyl alcohol and polymeric associations (PVA/blends) as a matrix for release capable of modifying the pharmacokinetic profile of different active ingredients in the regeneration of connective, epithelial, muscular, and nervous tissues. Articles were selected by three independent reviewers by analyzing the databases, such as Web of Science, PubMed, Science Direct, and Google Scholar (last 10 years). Descriptors used were "nanofibers", "poly (vinyl alcohol)", "muscle tissue", "connective tissue", "epithelial tissue", and "neural tissue engineering". The guiding question was: How do different compositions of polyvinyl alcohol polymeric nanofibers modify the pharmacokinetics of active ingredients in different tissue regeneration processes? The results demonstrated the versatility of the production of PVA nanofibers by solution blow technique with different actives (lipo/hydrophilic) and with pore sizes varying between 60 and 450 nm depending on the polymers used in the mixture, which influences the drug release that can be controlled for hours or days. The tissue regeneration showed better cellular organization and greater cell proliferation compared to the treatment with the control group, regardless of the tissue analyzed. We highlight that, among all blends, the combinations PVA/PCL and PVA/CS showed good compatibility and slow degradation, indicating their use in prolonged times of biodegradation, thus benefiting tissue regeneration in bone and cartilage connective tissues, acting as a physical barrier that results in guided regeneration, and preventing the invasion of cells from other tissues with increased proliferation rate.

Preparation of covalent organic framework-based nanofibrous films with temperature-responsive release of thymol for active food packaging

Thymol (THY) is commonly used in active food packaging, however because of its high volatility, poor water solubility, and strong aromatic odor, the application of THY is facing challenges. Herein, covalent organic frameworks (COFs) were synthesized in room temperature by asymmetric monomer exchange method for THY encapsulation, and solution blow spinning was used to fabricate the THY@COF/polycaprolactone (PCL) nanofibrous films. The synthesized COFs had a large specific surface area, porous structure, and loading capacity of 30.35% for THY, and THY@COFs possessed good thermal stability. Characterization analysis showed that THY@COFs were successfully incorporated into the PCL films and increased the barrier property of the films. Besides, the films showed good biocompatibility and antibacterial activity. Moreover, THY@COF/PCL films exhibited temperature-responsive THY release profiles, which is important for practical preservation applications, especially for preserving food in warm environments. Overall, THY@COF/PCL films possess promising potential in active food packaging.

Research progress in preparation, properties, and applications of medical protective fiber materials

A variety of public health events seriously threaten human life and health, especially the outbreak of COVID-19 at the end of 2019 has caused a serious impact on human production and life. Wearing personal protective equipment (PPE) is one of the most effective ways to prevent infection and stop the spread of the virus. Medical protective fiber materials have become the first choice for PPE because of their excellent barrier properties and breathability. In this article, we systematically review the latest progress in preparation technologies, properties, and applications of medical protective fiber materials. We first summarize the technological characteristics of different fiber preparation methods and compare their advantages and disadvantages. Then the barrier properties, comfort, and mechanical properties of the medical protective fiber materials used in PPE are discussed. After that, the applications of medical protective fibers in PPE are introduced, and protective clothing and masks are discussed in detail. Finally, the current status, future development trend, and existing challenges of medical protective fiber materials are summarized.

Advancement of Nonwoven Fabrics in Personal Protective Equipment

While nonwoven fabrics have existed for several decades, their usage in personal protective equipment (PPE) has been met with a rapid surge of demands, in part due to the recent COVID-19 pandemic. This review aims to critically examine the current state of nonwoven PPE fabrics by exploring (i) the material constituents and processing steps to produce fibers and bond them, and (ii) how each fabric layer is integrated into a textile, and how the assembled textiles are used as PPE. Firstly, filament fibers are manufactured via dry, wet, and polymer-laid fiber spinning methods. Then the fibers are bonded via chemical, thermal, and mechanical means. Emergent nonwoven processes such as electrospinning and centrifugal spinning to produce unique ultrafine nanofibers are discussed. Nonwoven PPE applications are categorized as filters, medical usage, and protective garments. The role of each nonwoven layer, its role, and textile integration are discussed. Finally, the challenges stemming from the single-use nature of nonwoven PPEs are discussed, especially in the context of growing concerns over sustainability. Then, emerging solutions to address sustainability issues with material and processing innovations are explored.

The preparation, resources, applications, and future trends of nanofibers in active food packaging: a review

Active packaging is a novel strategy for maintaining the shelf life of products and ensuring their safety, freshness, and integrity that has emerged with the consumer demand for safer, healthier, and higher quality food. Nanofibers have received a lot of attention for the application in active food packaging due to their high specific surface area, high porosity, and high loading capacity of active substances. Three common methods (electrospinning, solution blow spinning, and centrifugal spinning) for the preparation of nanofibers in active food packaging and their influencing parameters are presented, and advantages and disadvantages between these methods are compared. The main natural and synthetic polymeric substrate materials for the nanofiber preparation are discussed; and the application of nanofibers in active packaging is elaborated. The current limitations and future trends are also discussed. There have been many studies on the preparation of nanofibers using substrate materials from different sources for active food packaging. However, most of these studies are still in the laboratory research stage. Solving the issues of preparation efficiency and cost of nanofibers is the key to their application in commercial food packaging.

Recent advances and future challenges of the starch-based bio-composites for engineering applications

Starch is regarded as one of the most promising sustainable materials due to its abundant yield and excellent biodegradability. From the perspective of practical engineering applications, this paper systematically describes the development of starch-based bio-composites in the past decade. Packaging properties, processing characteristics, and current challenges for the efficient processing of starch-based bio-composites are reviewed in industrial packaging. Green coatings, binders, adsorbents, flocculants, flame retardants, and emulsifiers are used as examples to illustrate the versatility of starch-based bio-composites in chemical agent applications. In addition, the work compares the application of starch-based bio-composites in conventional spinning with emerging spinning technologies and describes the challenges of electrostatic spinning for preparing nanoscale starch-based fibers. In terms of flexible electronics, the starch-based bio-composites are regard as a solid polymer electrolyte and easily modified porous material. Moreover, we describe the applications of the starch-based gels in tissue engineering, controlled drug release, and medical dressings. Finally, the theoretical input and technical guidance in the advanced sustainable engineering application of the starch-based bio-composites are provided in the work.

Al/CuO@CNFs Conductive Flexible Energetic Films with High Electrical Safety

The development of energetic materials with both high energy and high safety has always been the focus of the field of energetic materials. In this paper, a low-current-sensitivity flexible energetic film composed of carbon nanofibers (CNFs)-coated Al/CuO metastable intermolecular composites (MICs) was prepared by a blow-spinning combined with controlled heat treatment technique. Hotspots can hardly generate in this kind of energetic film due to the increased electrical and thermal conductivity, leading to low sensitivity of MICs. It evenly stays at a high voltage (60 V) for 24 h without raising the temperature significantly. The energetic films keep the high energy release of MICs due to the additional violent reactions between CuO and CNFs as well as the light weight of CNFs, showing the heat release of 2864 J/g. In addition, the obtained films exhibit good mechanical properties and can maintain the structural integrity after 1000 cycles of repeated bending to a 6 mm curvature radius. The above characteristics reveal that energetic films presented in this paper have certain safety, high energy, and flexibility and have potential applications in transient electronics with flexible requirements such as micro-electromechanical system.

Multilayered blow-spun vascular prostheses with luminal surfaces in Nano/Micro range: the influence on endothelial cell and platelet adhesion

BACKGROUND

In this study, two types of polyurethane-based cylindrical multilayered grafts with internal diameters ≤ 6 mm were produced by the solution blow spinning (SBS) method. The main aim was to create layered-wall prostheses differing in their luminal surface morphology. Changing the SBS process parameters, i.e. working distance, rotational speed, volume, and concentration of the polymer solution allowed to obtain structures with the required morphologies. The first type of prostheses, termed Nano, possessed nanofibrous luminal surface, and the second type, Micro, presented morphologically diverse luminal surface, with both solid and microfibrous areas.

RESULTS

The results of mechanical tests confirmed that designed prostheses had high flexibility (Young's modulus value of about 2.5 MPa) and good tensile strength (maximum axial load value of about 60 N), which meet the requirements for vascular prostheses. The influence of the luminal surface morphology on platelet adhesion and the attachment of endothelial cells was investigated. Both surfaces did not cause hemolysis in contact with blood, the percentage of platelet-occupied area for Nano and Micro surfaces was comparable to reference polytetrafluoroethylene (PTFE) surface. However, the change in morphology of surface-adhered platelets between Nano and Micro surfaces was visible, which might suggest differences in their activation level. Endothelial coverage after 1, 3, and 7 days of culture on flat samples (2D model) was higher on Nano prostheses as compared with Micro scaffolds. However, this effect was not seen in 3D culture, where cylindrical prostheses were colonized using magnetic seeding method.

CONCLUSIONS

We conclude the produced scaffolds meet the material and mechanical requirements for vascular prostheses. However, changing the morphology without changing the chemical modification of the luminal surface is not sufficient to achieve the appropriate effectiveness of endothelialization in the 3D model.

Release Profiles of Carvacrol or Chlorhexidine of PLA/Graphene Nanoplatelets Membranes Prepared Using Electrospinning and Solution Blow Spinning: A Comparative Study

Nanofibrous membranes are often the core components used to produce devices for a controlled release and are frequently prepared by electrospinning (ES). However, ES requires high production times and costs and is not easy to scale. Recently, solution blow spinning (SBS) has been proposed as an alternative technique for the production of nanofibrous membranes. In this study, a comparison between these two techniques is proposed. Poly (lactic acid)-based nanofibrous membranes were produced by electrospinning (ES) and solution blow spinning (SBS) in order to evaluate the different effect of liquid (carvacrol, CRV) or solid (chlorhexidine, CHX) molecules addition on the morphology, structural properties, and release behavior. The outcomes revealed that both ES and SBS nanofibrous mat allowed for obtaining a controlled release up to 500 h. In detail, the lower wettability of the SBS system allowed for slowing down the CRV release kinetics, compared to the one obtained for ES membranes. On the contrary, with SBS, a faster CHX release can be obtained due to its more hydrophilic behavior. Further, the addition of graphene nanoplatelets (GNP) led to a decrease in wettability and allowed for a slowing down of the release kinetics in the whole of the systems.

Encapsulation of Monodisperse Microdroplets in Nanofibers through a Microfluidic-Electrospinning Hybrid Method

Fibers with droplets encapsulated in them could build bridges between a 0D dispersed structure and a 1D continuous wire and thus provide optimal solutions requiring high surface-to-volume ratio and strong mechanical properties. However, current methods are mostly focusing on the architectures with the size of droplets smaller than that of fibers; the relatively thick barrier of fibers usually limits the rate of diffusion from inner droplets to the outer environment. Here, we report a hybrid method combining microfluidics and electrospinning to fabricate nanofibers with microdroplets encapsulated in them. Monodisperse microdroplets with controllable sizes from 36 to 95 μm are generated through microfluidic flow-focusing and split into a string of smaller droplets from 1 to 3 μm, respectively, during the electrospinning stretching. The size of encapsulated droplets could be tuned by controlling the flow rate ratio during the microfluidic process, and the shape of that could be varied by changing the viscosity of encapsulated solution. This marriage of microfluidics and electrospinning could be applied to produce a nanofiber-based moisture barrier and drug carrier, also providing efficient tools to study the under-electric-field stretching and splitting of droplets trapped in the polymer network.

Recent Progress of Electrospun Herbal Medicine Nanofibers

Herbal medicine has a long history of medical efficacy with low toxicity, side effects and good biocompatibility. However, the bioavailability of the extract of raw herbs and bioactive compounds is poor because of their low water solubility. In order to overcome the solubility issues, electrospinning technology can offer a delivery alternative to resolve them. The electrospun fibers have the advantages of high specific surface area, high porosity, excellent mechanical strength and flexible structures. At the same time, various natural and synthetic polymer-bound fibers can mimic extracellular matrix applications in different medical fields. In this paper, the development of electrospinning technology and polymers used for incorporating herbal medicine into electrospun nanofibers are reviewed. Finally, the recent progress of the applications of these herbal medicine nanofibers in biomedical (drug delivery, wound dressing, tissue engineering) and food fields along with their future prospects is discussed.

Fibrous hydrogels by electrospinning: Novel platforms for biomedical applications

Hydrogels, hydrophilic and biocompatible polymeric networks, have been used for numerous biomedical applications because they have exhibited abilities to mimic features of extracellular matrix (ECM). In particular, the hydrogels engineered with electrospinning techniques have shown great performances in biomedical applications. Electrospinning techniques are to generate polymeric micro/nanofibers that can mimic geometries of natural ECM by drawing micro/nanofibers from polymer precursors with electrical forces, followed by structural stabilization of them. By exploiting the electrospinning techniques, the fibrous hydrogels have been fabricated and utilized as 2D/3D cell culture platforms, implantable scaffolds, and wound dressings. In addition, some hydrogels that respond to external stimuli have been used to develop biosensors. For comprehensive understanding, this review covers electrospinning processes, hydrogel precursors used for electrospinning, characteristics of fibrous hydrogels and specific biomedical applications of electrospun fibrous hydrogels and highlight their potential to promote use in biomedical applications.

Recent progress in fiber-based soft electronics enabled by liquid metal

Soft electronics can seamlessly integrate with the human skin which will greatly improve the quality of life in the fields of healthcare monitoring, disease treatment, virtual reality, and human-machine interfaces. Currently, the stretchability of most soft electronics is achieved by incorporating stretchable conductors with elastic substrates. Among stretchable conductors, liquid metals stand out for their metal-grade conductivity, liquid-grade deformability, and relatively low cost. However, the elastic substrates usually composed of silicone rubber, polyurethane, and hydrogels have poor air permeability, and long-term exposure can cause skin redness and irritation. The substrates composed of fibers usually have excellent air permeability due to their high porosity, making them ideal substrates for soft electronics in long-term applications. Fibers can be woven directly into various shapes, or formed into various shapes on the mold by spinning techniques such as electrospinning. Here, we provide an overview of fiber-based soft electronics enabled by liquid metals. An introduction to the spinning technology is provided. Typical applications and patterning strategies of liquid metal are presented. We review the latest progress in the design and fabrication of representative liquid metal fibers and their application in soft electronics such as conductors, sensors, and energy harvesting. Finally, we discuss the challenges of fiber-based soft electronics and provide an outlook on future prospects.

Solvent modulation in peptide sub-microfibers obtained by solution blow spinning

Peptides possess high chemical diversity at the amino acid sequence level, which further translates into versatile functions. Peptides with self-assembling properties can be processed into diverse formats giving rise to bio-based materials. Peptide-based spun fibers are an interesting format due to high surface-area and versatility, though the field is still in its infancy due to the challenges in applying the synthetic polymer spinning processes to protein fibers to peptides. In this work we show the use of solution blow-spinning to produce peptide fibers. Peptide fiber formation was assisted by the polymer poly (vinyl pyrrolidone) (PVP) in two solvent conditions. Peptide miscibility and further self-assembling propensity in the solvents played a major role in fiber formation. When employing acetic acid as solvent, peptide fibers (0.5 μm) are formed around PVP fibers (0.75 μm), whereas in isopropanol only one type of fibers are formed, consisting of mixed peptide and PVP (1 μm). This report highlights solvent modulation as a mean to obtain different peptide sub-microfibers via a single injection nozzle in solution blow spinning. We anticipate this strategy to be applied to other small peptides with self-assembly propensity to obtain multi-functional proteinaceous fibers.

Electrospinning vs. Electro-Assisted Solution Blow Spinning for Fabrication of Fibrous Scaffolds for Tissue Engineering

Biodegradable polymeric fibrous non-woven materials are widely used type of scaffolds for tissue engineering. Their morphology and properties could be controlled by composition and fabrication technology. This work is aimed at development of fibrous scaffolds from a multicomponent polymeric system containing biodegradable synthetic (polylactide, polycaprolactone) and natural (gelatin, chitosan) components using different methods of non-woven mats fabrication: electrospinning and electro-assisted solution blow spinning. The effect of the fabrication technique of the fibrous materials onto their morphology and properties, including the ability to support adhesion and growth of cells, was evaluated. The mats fabricated using electrospinning technology consist of randomly oriented monofilament fibers, while application of solution blow spinning gave a rise to chaotically arranged multifilament fibers. Cytocompatibility of all fabricated fibrous mats was confirmed using in vitro analysis of metabolic activity, proliferative capacity and morphology of NIH 3T3 cell line. Live/Dead assay revealed the formation of the highest number of cell-cell contacts in the case of multifilament sample formed by electro-assisted solution blow spinning technology.

Rotary Jet Spinning (RJS): A Key Process to Produce Biopolymeric Wound Dressings

Wounds result from different causes (e.g., trauma, surgeries, and diabetic ulcers), requiring even extended periods of intensive care for healing, according to the patient's organism and treatment. Currently, wound dressings generated by polymeric fibers at micro and nanometric scales are promising for healing the injured area. They offer great surface area and porosity, mimicking the fibrous extracellular matrix structure, facilitating cell adhesion, migration, and proliferation, and accelerating the wound healing process. Such properties resulted in countless applications of these materials in biomedical and tissue engineering, also as drug delivery systems for bioactive molecules to help tissue regeneration. The techniques used to engineer these fibers include spinning methods (electro-, rotary jet-), airbrushing, and 3D printing. These techniques have important advantages, such as easy-handle procedure and process parameters variability (type of polymer), but encounter some scalability problems. RJS is described as a simple and low-cost technique resulting in high efficiency and yield for fiber production, also capable of bioactive agents' incorporation to improve the healing potential of RJS wound dressings. This review addresses the use of RJS to produce polymeric fibers, describing the concept, type of configuration, comparison to other spinning techniques, most commonly used polymers, and the relevant parameters that influence the manufacture of the fibers, for the ultimate use in the development of wound dressings.

Superhydrophobic nanofibrous sponge with hierarchically layered structure for efficient harsh environmental oil-water separation

Oil leakage has posed serious threat to the environment, but still remain a great challenge to be solved especially for harsh environmental conditions. Herein, robust superhydrophobic nickel hydroxide grown by hydrothermal method and stearic acid modification on a blow-spun polyacrylonitrile (PAN)/Al₂O₃ nanofibrous sponge was proposed, so that the nickel hydroxide-modified polyacrylonitrile sponge (NPAS) was successfully obtained for efficient oil-water separation. The porous NPAS with a distinctive hierarchically layered structure, which exhibited excellent separation efficiency and mechanical elasticity. Due to its superhydrophobic and high porosity, the absorption capacity of NPAS could reach as high as 45 g g^-1. It could not only separate a series of oil-water mixture with a high steady flux of 12,413 L m^-2 h^-1 (dichloromethane-water), but also separate stabilized emulsions with a superior flux 2032 L m^-2 h^-1 (water-in-dichloromethane) under gravity, all of that with above 99.92% separation efficiencies, which was higher than that of the most reported sponges. Most importantly, its strong acid/alkali resistance enable it is suitable for hazardous materials treatment applications in harsh environmental conditions. This novel NPAS via facile large-scale blow-spinning provide an efficient strategy for oil-containing wastewater treatment and environmental protection.

Improved Forward Osmosis Performance of Thin Film Composite Membranes with Graphene Quantum Dots Derived from Eucalyptus Tree Leaves

The major challenges in forward osmosis (FO) are low water flux, high specific reverse solute flux (SRSF), and membrane fouling. The present work addresses these problems by the incorporation of graphene quantum dots (GQDs) in the polyamide (PA) layer of thin-film composite (TFC) membranes, as well as by using an innovative polyethersulfone nanofiber support for the TFC membrane. The GQDs were prepared from eucalyptus leaves using a facile hydrothermal method that requires only deionized water, without the need for any organic solvents or reducing agents. The nanofiber support of the TFC membranes was prepared using solution blow spinning (SBS). The polyamide layer with GQDs was deposited on top of the nanofiber support through interfacial polymerization. This is the first study that reports the fouling resistance of the SBS-nanofiber-supported TFC membranes. The effect of various GQD loadings on the TFC FO membrane performance, its long-term FO testing, cleaning efficiency, and organic fouling resistance were analyzed. It was noted that the FO separation performance of the TFC membranes was improved with the incorporation of 0.05 wt.% GQDs. This study confirmed that the newly developed thin-film nanocomposite membranes demonstrated increased water flux and salt rejection, reduced SRSF, and good antifouling performance in the FO process.

Fully Fibrous Large-Area Tailorable Triboelectric Nanogenerator Based on Solution Blow Spinning Technology for Energy Harvesting and Self-Powered Sensing

An all-fibrous large-area (20 × 50 cm² ) tailorable triboelectric nanogenerator (LT-TENG) is prepared using a one-step solution blow spinning technology, which has the advantages of easy operation, scale-up in the area, and high production efficiency. The prepared LT-TENG is composed of polyvinylidene fluoride (PVDF)/MXene (Ti₃ C₂ T_x ) nanofibers (NFs) and conductive textile. Benefiting from the fibrous materials and large-area properties, the LT-TENG possesses the merits of good tailorability, breathability, hydrophobicity, and washability. When optimized by mixing the MXene into PVDF NFs, the LT-TENG has a preferable output and sensing property, with a detection range over 16 kPa and a relatively high sensitivity of 12.33 V KPa^-1 . At maximum applied pressure, the voltage, current, and charge are 108 V, 38 µA, and 35 nC, respectively. This LT-TENG can serve as a biomechanical energy harvester when used as wearable devices with an output power density of 12.6 mW m^-2 at an external load resistance of 500 MΩ, and it also has the ability of self-powered tactile sensing for pressure mapping and slide sensing. Thus, this LT-TENG exhibits great potential prospects in wearable devices, intelligent robots, and human-machine interaction.

Solution blow spinning polysulfone-Aliquat 336 nanofibers: synthesis, characterization, and application for the extraction and preconcentration of losartan from aqueous solutions

Nanofibers are materials used in a wide range of applications due to their unique physicochemical properties. As an alternative to the most common method of its manufacturing (electrospinning) blow spinning has been used since it has greater production efficiency and simplicity. A wide variety of polymers is used for its preparation and can be modified to improve the interaction and selectivity toward specific analytes. Thereby nanofibers have been used for the extraction or removal of organic compounds such as drugs but there are still few reports of drug extractions like losartan. In this work polysulfone-Aliquat 336 nanofibers were prepared using the blow spinning method to extract and preconcentrate losartan. The studies showed that Aliquat 336 incorporation significantly improve the extraction of losartan with polysulfone fibers. Adsorption process was thermodynamically favorable with an adsorption capacity of 15.45 mg·g−1. Thus, it was possible to extract more than 92% of initial losartan using 10 mg of polysulfone-Aliquat 336 fibers (9 and 3.5% (w/v)), at pH 6 from deionized water and synthetic wastewater. Finally, losartan preconcentration was evaluated to facilitate its quantification using ultraviolet–visible spectrometry (UV-Vis), which allowed the determination of this drug at concentrations below the detection limit.

Two-Dimensional Hybrid Nanosheet-Based Supercapacitors: From Building Block Architecture, Fiber Assembly, and Fabric Construction to Wearable Applications

Fiber-based supercapacitors (F-SCs) have inspired widespread interest in the fields of wearable technology, energy, and carbon neutralization due to their highly deformable flexibility, fast charging/discharging capability, long-term stability, and energy conservation ability. In this review, we summarize the latest developments for fabricating fibrous electrodes of F-SCs where advanced micro two-dimensional (2D) building blocks (e.g., MXene and graphene) are chemically assembled and constructed into ordered mesofibers and multifunctional macrofabrics. Diverse fundamental principles of 2D hybrid nanosheets with respect to surface controls, pseudocapacitive modifications, and microstructural manipulations, promoting rapid electron transfer and charge conduction, are introduced. Additionally, various spinning methods for assembling and fabricating sophisticated fibers with advanced nano/microstructures, including hierarchical skeletons, anisotropic backbones, surface/entire porous frameworks, and vertical-aligned networks, for boosting ionic kinetic transport/storage are presented. Likewise, the structure-activity relationships between the porous structure and electrochemical performance are clarified. Moreover, multifunctional fabrics in terms of high flexibilities/strengths, superior electrical conductivities, and stabilized operations, which realize large energy density, deformable capability, and robust stability under harsh conditions, are emphasized. In particular, the potential power-supply applications, including flexible electronic devices, self-powered functions, and energy-sensor systems, are highlighted. Finally, a short conclusion and outlook, along with the current challenges and future opportunities of next-generation F-SCs, are proposed.

Electrospun Nanofibers for Wound Management

Electrospun nanofibers show great potential in biomedical applications. This mini review article traces the recent advances in electrospun nanofibers for wound management via various approaches. Initially, we provide a short note on the four phases of wound healing, including hemostasis, inflammation, proliferation, and remodeling. Then, we state how the nanofiber dressings can stop bleeding and reduce the pain. Following that, we discuss the delivery of therapeutics and cells using different types of nanofibers for enhancing cell migration, angiogenesis, and re-epithelialization, resulting in the promotion of wound healing. Finally, we present the conclusions and future perspectives regarding the use of electrospun nanofibers for wound management.