Water-solid contact electrification causes hydrogen peroxide production from hydroxyl radical recombination in sprayed microdroplets

Oxidation of Ammonia in Water Microdroplets Produces Nitrate and Molecular Hydrogen

Water microdroplets containing dissolved ammonia (30-300 μM) are sprayed through a copper oxide mesh with a 200 μm average pore size, resulting in the formation of nitrate (NO3-) and the release of molecular hydrogen (H2). The products result from a redox process that takes place at the liquid-solid interface through contact electrification, where no external potential is applied. Oxidation is initiated by superoxide radical anions (O2-) that originate from the oxygen in the air surrounding the microdroplets and from the hydroxyl radicals (OH•) originating from the water-air interface. Two spin traps (TEMPO and DMPO) capture these radicals as well as NH2OH+•, HNO, NO•, NO2•, and NOOH, which are detected by mass spectrometry. We also directly observed N2O2-• by the same means. We found that the hydrogen atom from the ammonia molecule can be set free not only in the form of H• but also as H2, which is detected using a residue gas analyzer. The oxidation process can be significantly enhanced by a factor of 3 when the sprayed microdroplets are irradiated with ultraviolet light (265 nm, 5 W). 35% of 300 μM ammonia can be degraded within 20 μs, and the nitrate conversion rate is estimated to be 15 nmol·mg-1·h-1.

Unveiling Contact-Electrification Effect on Interfacial Water Oscillation

Water is crucial for various physicochemical processes at the liquid-solid interfaces. In particular, the interfacial water, mediating the electric field and solvation effect along with the solid, corporately determine the electrochemical properties. Understanding the interaction between solid properties and the interface water holds significant importance in interfacial dynamics. However, the impact of alterations in the charged state of solid surfaces induced by contact electrification on interfacial water remains unknown. Here, the evolution of atomic-level resolution maps of hydration layers are reported on charged surfaces using 3D atomic force microscopy (3D-AFM). These findings demonstrate that electrostatic interactions can reinforce, distort, or collapse the characteristic structure of hydration layers. More importantly, these interactions exhibit interlayer differences and sample specificity in hydration layer structures of different substrates. In addition, similar oscillations of the hydration layer are observed at the electrochemical interface under different voltage biases. This suggests that contact-electrification has the potential to serve as a novel method for manipulating and regulating chemical reactions at the interface.

Understanding dynamic voltammetry in a dissolving microdroplet

Droplet evaporation and dissolution phenomena are pervasive in both natural and artificial systems, playing crucial roles in various applications. Understanding the intricate processes involved in the evaporation and dissolution of sessile droplets is of paramount importance for applications such as inkjet printing, surface coating, and nanoparticle deposition, etc. In this study, we present a demonstration of electrochemical investigation of the dissolution behaviour in sub-nL droplets down to sub-pL volume. Droplets on an electrode have been studied for decades in the field of electrochemistry to understand the phase transfer of ions at the oil-water interface, accelerated reaction rates in microdroplets, etc. However, the impact of microdroplet dissolution on the redox activity of confined molecules within the droplet has not been explored previously. As a proof-of-principle, we examine the dissolution kinetics of 1,2-dichloroethane droplets (DCE) spiked with 155 μM decamethylferrocene within an aqueous phase on an ultramicroelectrode (r = 6.3 μm). The aqueous phase serves as an infinite sink, enabling the dissolution of DCE droplets while also facilitating convenient electrical contact with the reference/counter electrode (Ag/AgCl 1 M KCl). Through comprehensive voltammetric analysis, we unravel the impact of droplet dissolution on electrochemical response as the droplet reaches minuscule volumes. We validate our experimental findings by finite element modelling, which shows deviations from the experimental results as the droplet accesses negligible volumes, suggesting the presence of complex dissolution modes.

H2O2 Photosynthesis from H2O and O2 under Weak Light by Carbon Nitrides with the Piezoelectric Effect

Driven by the essential need of a green, safe, and low-cost approach to producing H2O2, a highly valuable multifunctional chemical, artificial photosynthesis emerges as a promising avenue. However, current catalyst systems remain challenging, due to the need of high-density sunlight, poor selectivity and activity, or/and unfavorable thermodynamics. Here, we reported that an indirect 2e- water oxidation reaction (WOR) in photocatalytic H2O2 production was unusually activated by C5N2 with piezoelectric effects. Interestingly, under ultrasonication, C5N2 exhibited an overall H2O2 photosynthesis rate of 918.4 μM/h and an exceptionally high solar-to-chemical conversion efficiency of 2.6% after calibration under weak light (0.1 sun). Mechanism studies showed that the piezoelectric effect of carbon nitride overcame the high uphill thermodynamics of *OH intermediate generation, which enabled a new pathway for 2e- WOR, the kinetic limiting step in the overall H2O2 production from H2O and O2. Benefiting from the outstanding sonication-assisted photocatalytic H2O2 generation under weak light, the concept was further successfully adapted to biomedical applications in efficient sono-photochemodynamic therapy for cancer treatment and water purification.

Water Vapor Condensation Triggers Simultaneous Oxidation and Hydrolysis of Organic Pollutants on Iron Mineral Surfaces

Increasing worldwide contamination with organic chemical compounds is a paramount environmental challenge facing humanity. Once they enter nature, pollutants undergo transformative processes that critically shape their environmental impacts and associated risks. This research unveils previously overlooked yet widespread pathways for the transformations of organic pollutants triggered by water vapor condensation, leading to spontaneous oxidation and hydrolysis of organic pollutants. These transformations exhibit variability through either sequential or parallel hydrolysis and oxidation, contingent upon the functional groups within the organic pollutants. For instance, acetylsalicylic acid on the goethite surface underwent sequential hydrolysis and oxidation that first hydrolyzed to salicylic acid followed by hydroxylation oxidation of the benzene moiety driven by the hydroxyl radical (•OH). In contrast, chloramphenicol underwent parallel oxidation and hydrolysis, forming hydroxylated chloramphenicol and 2-amino-1-(4-nitrophenyl)-1,3-propanediol, respectively. The spontaneous oxidation and hydrolysis occurred consistently on three naturally abundant iron minerals with the key factors being •OH production capacity and surface binding strength. Given the widespread presence of iron minerals on Earth's surface, these spontaneous transformation paths could play a role in the fate and risks of organic pollutants of health concerns.

Insights into the Formation Mechanism of Reactive Oxygen Species in the Interface Reaction of SO2 on Hematite

The interplay between sulfur and iron holds significant importance in their atmospheric cycle, yet a complete understanding of their coupling mechanism remains elusive. This investigation delves comprehensively into the evolution of reactive oxygen species (ROS) during the interfacial reactions involving sulfur dioxide (SO2) and iron oxides under varying relative humidity conditions. Notably, the direct activation of water by iron oxide was observed to generate a surface hydroxyl radical (•OH). In comparison, the aging of SO2 was found to markedly augment the production of •OH radicals on the surface of α-Fe2O3 under humid conditions. This augmentation was ascribed to the generation of superoxide radicals (•O2-) stemming from the activation of O2 through the Fe(II)/Fe(III) cycle and its combination with the H+ ion to produce hydrogen peroxide (H2O2) on the acidic surface. Moreover, the identification of moderate relative humidity as a pivotal factor in sustaining the surface acidity of iron oxide during SO2 aging underscores its crucial role in the coupling of iron dissolution, ROS production, and SO2 oxidation. Consequently, the interfacial reactions between SO2 and iron oxides under humid conditions are elucidated as atmospheric processes that enhance oxidation capacity rather than deplete ROS. These revelations offer novel insights into the mechanisms underlying •OH radical generation and oxidative potential within atmospheric interfacial chemistry.

How liquids charge the superhydrophobic surfaces

Liquid-solid contact electrification (CE) is essential to diverse applications. Exploiting its full implementation requires an in-depth understanding and fine-grained control of charge carriers (electrons and/or ions) during CE. Here, we decouple the electrons and ions during liquid-solid CE by designing binary superhydrophobic surfaces that eliminate liquid and ion residues on the surfaces and simultaneously enable us to regulate surface properties, namely work function, to control electron transfers. We find the existence of a linear relationship between the work function of superhydrophobic surfaces and the as-generated charges in liquids, implying that liquid-solid CE arises from electron transfer due to the work function difference between two contacting surfaces. We also rule out the possibility of ion transfer during CE occurring on superhydrophobic surfaces by proving the absence of ions on superhydrophobic surfaces after contact with ion-enriched acidic, alkaline, and salt liquids. Our findings stand in contrast to existing liquid-solid CE studies, and the new insights learned offer the potential to explore more applications.

Spontaneous Wetting Induced by Contact-Electrification at Liquid-Solid Interface

Wettability significantly influences various surface interactions and applications at the liquid-solid interface. However, the understanding is complicated by the intricate charge exchange occurring through contact electrification (CE) during this process. The understanding of the influence of triboelectric charge on wettability remains challenging, especially due to the complexities involved in concurrently measuring contact angles and interfacial electrical signals. Here, the relationship is investigated between surface charge density and change of contact angle of dielectric films after contact with water droplets. It is observed that the charge exchange when water spared lead to a spontaneous wetting phenomenon, which is termed as the contact electrification induced wetting (CEW). Notably, these results demonstrate a linear dependence between the change of contact angle (CA) of the materials and the density of surface charge on the solid surface. Continuous CEW tests show that not only the static CA but also the dynamics of wetting are influenced by the accumulation charges at the interface. The mechanism behind CEW involves the redistribution of surface charges on a solid surface and polar water molecules within liquid. This interaction results in a decrease in interface energy, leading to a reduction in the CA. Ab initio calculations suggest that the reduction in interface energy may stem from the enhanced surface charge on the substrate, which strengthens the hydrogen bond interaction between water and the substrate. These findings have the potential to advance the understanding of CE and wetting phenomena, with applications in energy harvesting, catalysis, and droplet manipulation at liquid-solid interfaces.

Chemical Kinetics in Microdroplets

Micrometer-sized compartments play significant roles in driving heterogeneous transformations within atmospheric and biochemical systems as well as providing vehicles for drug delivery and novel reaction environments for the synthesis of industrial chemicals. Many reports now indicate that reaction kinetics are accelerated under microconfinement, for example, in sprays, thin films, droplets, aerosols, and emulsions. These observations are dramatic, posing a challenge to our understanding of chemical reaction mechanisms with potentially significant practical consequences for predicting the complex chemistry in natural systems. Here we introduce the idea of kinetic confinement, which is intended to provide a conceptual backdrop for understanding when and why microdroplet reaction kinetics differ from their macroscale analogs.

Microstructured gas-liquid-(solid) interfaces: A platform for sustainable synthesis of commodity chemicals

Gas-liquid-solid catalytic reactions are widespread in nature and man-made technologies. Recently, the exceptional reactivity observed on (electro)sprayed microdroplets, in comparison to bulk gas-liquid systems, has attracted the attention of researchers. In this perspective, we compile possible strategies to engineer catalytically active gas-liquid-(solid) interfaces based on membrane contactors, microdroplets, micromarbles, microbubbles, and microfoams to produce commodity chemicals such as hydrogen peroxide, ammonia, and formic acid. In particular, particle-stabilized microfoams, with superior upscaling capacity, emerge as a promising and versatile platform to conceive high-performing (catalytic) gas-liquid-(solid) nanoreactors. Gas-liquid-(solid) nanoreactors could circumvent current limitations of state-of-the-art multiphase reactors (e.g., stirred tanks, trickle beds, and bubble columns) suffering from poor gas solubility and mass transfer resistances and access gas-liquid-(solid) reactors with lower cost and carbon footprint.

My Vision of Electric-Field-Aided Chemistry in 2050

This manuscript outlines my outlook on the development of electric-field (EF)-mediated-chemistry and the vision of its state by 2050. I discuss applications of oriented-external electric-fields (OEEFs) on chemical reactions and proceed with relevant experimental verifications. Subsequently, the Perspective outlines other ways of generating EFs, e.g., by use of pH-switchable charges, ionic additives, water droplets, and so on. A special section summarizes conceptual principles for understanding and predicting OEEF effects, e.g., the "reaction-axis rule", the capability of OEEFs to act as tweezers that orient reactants and accelerate their reaction, etc. Finally, I discuss applications of OEEFs in continuous-flow setups, which may, in principle, scale-up to molar concentrations. The Perspective ends with the vision that by 2050, OEEF usage will change chemical education, if not also the art of making new molecules.

Reduction of precious metal ions in aqueous solutions by contact-electro-catalysis

Precious metals are core assets for the development of modern technologies in various fields. Their scarcity poses the question of their cost, life cycle and reuse. Recently, an emerging catalysis employing contact-electrification (CE) at water-solid interfaces to drive redox reaction, called contact-electro-catalysis (CEC), has been used to develop metal free mechano-catalytic methods to efficiently degrade refractory organic compounds, produce hydrogen peroxide, or leach metals from spent Li-Ion batteries. Here, we show ultrasonic CEC can successfully drive the reduction of Ag(ac), Rh3+, [PtCl4]2-, Ag+, Hg2+, Pd2+, [AuCl4]-, and Ir3+, in both anaerobic and aerobic conditions. The effect of oxygen on the reaction is studied by electron paramagnetic resonance (EPR) spectroscopy and ab-initio simulation. Combining measurements of charge transfers during water-solid CE, EPR spectroscopy and gold extraction experiments help show the link between CE and CEC. What's more, this method based on water-solid CE is capable of extracting gold from synthetic solutions with concentrations ranging from as low as 0.196 ppm up to 196 ppm, reaching in 3 h extraction capacities ranging from 0.756 to 722.5 mg g-1 in 3 h. Finally, we showed CEC is employed to design a metal-free, selective, and recyclable catalytic gold extraction methods from e-waste aqueous leachates.

Contact-Electro-Catalysis for Direct Oxidation of Methane under Ambient Conditions

The conversion of methane under ambient conditions has attracted significant attention. Although advancements have been made using active oxygen species from photo- and electro- chemical processes, challenges such as complex catalyst design, costly oxidants, and unwanted byproducts remain. This study exploits the concept of contact-electro-catalysis, initiating chemical reactions through charge exchange at a solid-liquid interface, to report a novel process for directly converting methane under ambient conditions. Utilizing the electrification of commercially available Fluorinated Ethylene Propylene (FEP) with water under ultrasound, we demonstrate how this interaction promote the activation of methane and oxygen molecules. Our results show that the yield of HCHO and CH3OH can reach 467.5 and 151.2 μmol ⋅ gcat -1, respectively. We utilized electron paramagnetic resonance (EPR) to confirm the evolution of hydroxyl radicals (⋅OH) and superoxide radicals (⋅OOH). Isotope mass spectrometry (MS) was employed to analyze the elemental origin of CH3OH, which can be further oxidized to HCHO. Additionally, we conducted density functional theory (DFT) simulations to assess the reaction energies of FEP with H2O, O2, and CH4 under these conditions. The implications of this methodology, with its potential applicability to a wider array of gas-phase catalytic reactions, underscore a significant advance in catalysis.

Contact-electro-catalysis (CEC)

Contact-electro-catalysis (CEC) is an emerging field that utilizes electron transfer occurring at the liquid-solid and even liquid-liquid interfaces because of the contact-electrification effect to stimulate redox reactions. The energy source of CEC is external mechanical stimuli, and solids to be used are generally organic as well as in-organic materials even though they are chemically inert. CEC has rapidly garnered extensive attention and demonstrated its potential for both mechanistic research and practical applications of mechanocatalysis. This review aims to elucidate the fundamental principle, prominent features, and applications of CEC by compiling and analyzing the recent developments. In detail, the theoretical foundation for CEC, the methods for improving CEC, and the unique advantages of CEC have been discussed. Furthermore, we outline a roadmap for future research and development of CEC. We hope that this review will stimulate extensive studies in the chemistry community for investigating the CEC, a catalytic process in nature.

Revealing the Contribution of Interfacial Processes to Atmospheric Oxidizing Capacity in Haze Chemistry

The atmospheric oxidizing capacity is the most important driving force for the chemical transformation of pollutants in the atmosphere. Traditionally, the atmospheric oxidizing capacity mainly depends on the concentration of O3 and other gaseous oxidants. However, the atmospheric oxidizing capacity based on gas-phase oxidation cannot accurately describe the explosive growth of secondary particulate matter under complex air pollution. From the chemical perspective, the atmospheric oxidizing capacity mainly comes from the activation of O2, which can be achieved in both gas-phase and interfacial processes. In the heterogeneous or multiphase formation pathways of secondary particulate matter, the enhancement of oxidizing capacity ascribed to the O2/H2O-involved interfacial oxidation and hydrolysis processes is an unrecognized source of atmospheric oxidizing capacity. Revealing the enhanced oxidizing capacity due to interfacial processes in high-concentration particulate matter environments and its contribution to the formation of secondary pollution are critical in understanding haze chemistry. The accurate evaluation of atmospheric oxidizing capacity ascribed to interfacial processes is also an important scientific basis for the implementation of PM2.5 and O3 collaborative control in China and around the world.

Reduction of Superoxide Radical Intermediate by Polydopamine for Efficient Hydrogen Peroxide Photosynthesis

The synthesis of hydrogen peroxide through artificial photosynthesis is a green and promising technology with advantages in sustainability, economy and safety. However, superoxide radical (⋅O2 -), an important intermediate in photocatalytic oxygen reduction to H2O2 production, has strong oxidizing properties that potentially destabilize the catalyst. Therefore, avoiding the accumulation of ⋅O2 - for its rapid conversion to H2O2 is of paramount significance in improving catalyst stability and H2O2 yield. In this work, a strategy was developed to utilize protonated groups for the rapid depletion of converted ⋅O2 -, thereby the efficiency of photocatalytic synthesis of H2O2 from CN was successfully enhanced by 47-fold. The experimental findings demonstrated that polydopamine not only improved carrier separation efficiency, and more importantly, provided the adsorption reduction active site for ⋅O2 - for efficient H2O2 production. This work offers a versatile approach for synthesizing efficient and stable photocatalysts.

Pyrogenic Carbon Degradation by Galvanic Coupling with Sprayed Seawater Microdroplets

Surface waves are known for their mechanical role in coastal processes that influence the weather and climate. However, their chemical impact, particularly on the transformation of pyrogenic carbon, is poorly understood. Pyrogenic carbon is generally assumed to show negligible postformational alteration of its stable carbon isotope composition. Here we present an electrochemical interaction of pyrogenic carbon with the sprayed seawater microdroplets resulting from wave breaking, driven by the galvanic coupling between the microdroplet water-carbon interfaces and the microdroplet water-vapor interfaces. This enables refractory pyrogenic carbon to rapidly degrade via the oxygenation and mineralization reaction, which makes it ∼2.6‰ enriched in 13C, far exceeding the generally assumed postformation alteration values (<0.5‰) of pyrogenic carbon. The unique chemical dynamics of seawater microdroplets provide new insights into the discrepancy in carbon isotope signatures between riverine and marine black carbon, emphasizing the potential of coastal oceans for carbon sequestration in the global carbon cycle.

Recent Progress of Solid-Liquid Interface-Mediated Contact-Electro-Catalysis

Contact electrification (CE) is a common physical process by which triboelectric charges are generated through the mutual contact between two objects. Despite the ongoing debates on CE's mechanism, recent advancements in technology have elucidated the primary role of electron transfer in most CE processes. This discovery leads to the spawning of an emerging field, known as contact-electro-catalysis (CEC), which utilizes the electron transfer phenomenon during CE to initiate CEC. In this work, we provide the first comprehensive review of the recent progress of the solid-liquid interface-mediated CEC process, including its working principles, relationship with surface science, recent breakthroughs in applications, and future challenges. We aim to provide fundamental guidance for researchers to understand the reaction mechanism of the CEC process and to propose potential pathways to enhance CEC efficiency from a surface and interfacial science perspective. Later, recent application scenarios using the novel CEC techniques are summarized, including wastewater treatment, efficient generation of hydrogen peroxide (H2O2), lithium-ion battery recycling, and CO2 reduction. In general, CEC technology has opened a new avenue for catalysis, effectively expanding the range of catalyst options and holding promise as a solution to a variety of complex catalytic challenges in the future.

The emerging chemistry of self-electrified water interfaces

Water is known for dissipating electrostatic charges, but it is also a universal agent of matter electrification, creating charged domains in any material contacting or containing it. This new role of water was discovered during the current century. It is proven in a fast-growing number of publications reporting direct experimental measurements of excess charge and electric potential. It is indirectly verified by its success in explaining surprising phenomena in chemical synthesis, electric power generation, metastability, and phase transition kinetics. Additionally, electrification by water is opening the way for developing green technologies that are fully compatible with the environment and have great potential to contribute to sustainability. Electrification by water shows that polyphasic matter is a charge mosaic, converging with the Maxwell-Wagner-Sillars effect, which was discovered one century ago but is still often ignored. Electrified sites in a real system are niches showing various local electrochemical potentials for the charged species. Thus, the electrified mosaics display variable chemical reactivity and mass transfer patterns. Water contributes to interfacial electrification from its singular structural, electric, mixing, adsorption, and absorption properties. A long list of previously unexpected consequences of interfacial electrification includes: "on-water" reactions of chemicals dispersed in water that defy current chemical wisdom; reactions in electrified water microdroplets that do not occur in bulk water, transforming the droplets in microreactors; and lowered surface tension of water, modifying wetting, spreading, adhesion, cohesion, and other properties of matter. Asymmetric capacitors charged by moisture and water are now promising alternative equipment for simultaneously producing electric power and green hydrogen, requiring only ambient thermal energy. Changing surface tension by interfacial electrification also modifies phase-change kinetics, eliminating metastability that is the root of catastrophic electric discharges and destructive explosions. It also changes crystal habits, producing needles and dendrites that shorten battery life. These recent findings derive from a single factor, water's ability to electrify matter, touching on the most relevant aspects of chemistry. They create tremendous scientific opportunities to understand the matter better, and a new chemistry based on electrified interfaces is now emerging.

Busting the myth of spontaneous formation of H2O2 at the air-water interface: contributions of the liquid-solid interface and dissolved oxygen exposed

Recent reports on the spontaneous formation of hydrogen peroxide (H2O2) at the air-water and solid-water interfaces challenge our current understanding of aquatic chemistry and have ramifications on atmosphere chemistry models, surface science, and green chemistry. Suggested mechanisms underlying this chemical transformation include ultrahigh instantaneous electric fields at the air-water interface and the oxidation of water and reduction of the solid at the solid-water interface. Here, we revisit this curious problem with NMR spectroscopy (with an H2O2 detection limit ≥50 nM) and pay special attention to the effects of nebulizing gas, dissolved oxygen content, and the solid-water interface on this chemical transformation in condensed and sprayed water microdroplets. Experiments reveal that the reduction of dissolved oxygen at the solid-water interface predominantly contributes to the H2O2 formation (not the oxidation of hydroxyl ions at the air-water interface or the oxidation of water at the solid-water interface). We find that the H2O2 formation is accompanied by the consumption (i.e., reduction) of dissolved oxygen and the oxidation of the solid surface, i.e., in the absence of dissolved oxygen, the formation of H2O2(aq) is not observed within the detection limit of ≥50 nM. Remarkably, the tendency of the solids investigated in this work towards forming H2O2 in water followed the same order as their positions in the classic Galvanic series. These findings bust the prevailing myths surrounding H2O2 formation due to the air-water interface, the ultrahigh electric fields therein, or the micro-scale of droplets. The hitherto unrealized role of the oxidation of the solid surface due to dissolved oxygen in the formation of H2O2 is exposed. These findings are especially relevant to corrosion science, surface science, and electrochemistry, among others.

Deciphering the Kinetics of Spontaneous Generation of H2O2 in Individual Water Microdroplets

Spontaneous generation of H2O2 in sub-10 μm-sized water microdroplets has received increasing interest since its first discovery in 2019. On the other hand, due to the short lifetime of these microdroplets (rapid evaporation) and lack of suitable tools to real-time monitor the generation of H2O2 in individual microdroplets, such a seemingly thermodynamically unfavorable process has also raised vigorous debates on the origin of H2O2 and the underlying mechanism. Herein, we prepared water microdroplets with a long lifetime (>1 h) by virtue of microwell confinement and dynamically monitored the spontaneous generation of H2O2 in individual microdroplets via time-lapsed fluorescence imaging. It was unveiled that H2O2 was continuously generated in the as-prepared water microdroplets and an apparent equilibrium concentration of ∼3 μM of H2O2 in the presence of a H2O2-consuming reaction can be obtained. Through engineering the geometry of these microdroplets, we further revealed that the generation rates of H2O2 in individual microdroplets were positively proportional to their surface-to-volume ratios. This also allowed us to extract a maximal H2O2 generation rate of 7.7 nmol m-2 min-1 in the presence of a H2O2-consuming reaction and derive the corresponding probability of spontaneous conversion of interfacial H2O into H2O2 for the first time, that is, ∼1 of 65,000 water molecules in 1 s. These findings delivered strong evidence that the spontaneous generation of H2O2 indeed occurs at the surface of microdroplets and provided us with an important starting point to further enhance the yield of H2O2 in water microdroplets for future applications.

Continuous ammonia synthesis from water and nitrogen via contact electrification

We synthesized ammonia (NH3) by bubbling nitrogen (N2) gas into bulk liquid water (200 mL) containing 50 mg polytetrafluoroethylene (PTFE) particles (~5 µm in diameter) suspended with the help of a surfactant (Tween 20, ~0.05 vol.%) at room temperature (25 °C). Electron spin resonance spectroscopy and density functional theory calculations reveal that water acts as the proton donor for the reduction of N2. Moreover, isotopic labeling of the N2 gas shows that it is the source of nitrogen in the ammonia. We propose a mechanism for ammonia generation based on the activation of N2 caused by electron transfer and reduction processes driven by contact electrification. We optimized the pH of the PTFE suspension at 6.5 to 7.0 and employed ultrasonic mixing. We found an ammonia production rate of ~420 μmol L-1 h-1 per gram of PTFE particles for the conditions described above. This rate did not change more than 10% over an 8-h period of sustained reaction.

Improving the electrocatalytic hydrogen evolution reaction through a magnetic field and hydrogen peroxide production co-assisted Ni/Fe3O4@poly(3,4-ethylene-dioxythiophene)/Ni electrode

The production of high-purity hydrogen using surplus electrical energy and abundant water resources has immense potential in mitigating the fossil energy crisis, as hydrogen fuel holds clean, pollution-free, and high-energy characteristics. However, the practical application of large-scale hydrogen production from water faces challenges such as high overpotentials, sluggish dynamics, and limited electrocatalytic lifetime associated with the hydrogen evolution reaction (HER). Here, we fabricated the sandwich structure of a Ni/Fe3O4@poly(3,4-ethylene-dioxythiophene)/Ni (Ni/Fe3O4@PEDOT/Ni) electrode and employed a strong magnet to obtain a magnetic electrode capable of achieving high-activity and durability for HER. Electrochemical analysis reveals that the activated magnetic electrode displays a significantly reduced overpotential and an extended electrocatalytic lifetime of 10 days. Notably, its stability is higher than that of non-magnetic Ni/Fe3O4/Ni and Ni/Fe3O4@PEDOT/Ni electrodes, primarily due to the support from magnetic force and the protective PEDOT layer. Moreover, the minute atomized droplets can form the H2O2 species in a moist environment, facilitating the formation of the NiO layer on the Ni surface, which plays a vital role in boosting catalytic activity. In conclusion, our magnetic electrode strategy, combined with the emergence of the NiO layer, offers valuable insights for the development of advanced HER electrodes.

Contact-Electro-Catalysis-Assisted Separation via a Dancing PTFE Membrane for Fouling Control

Advanced oxidization processes (AOPs) offer promising solutions for addressing the fouling issues in membrane separation systems. However, the high energy requirements for electrical or light power in the AOPs can be a drawback. In this study, we present a contact-electro-catalysis (CEC)-based approach for controlling membrane fouling, which is stimulated by mild ultrasonic irradiation. During this process, electrons are transferred between a dancing polytetrafluoroethylene membrane and water or oxygen molecules, resulting in the formation of free radicals •OH and •O2-. These free radicals are capable of degrading or inactivating foulants, eliminating the need for additional chemical cleaners, secondary waste disposal, or external stimuli. Furthermore, the time-dependent voltage spikes/oscillations (peak, +7.8/-8.2 V) generate a nonuniform electric field that drives dielectrophoresis, effectively keeping contaminants away from the membrane surface and further enhancing the antifouling performance of the dancing membrane. Therefore, the CEC-assisted membrane separation system offers a green and effective strategy for controlling membrane fouling through mild mechanical stimulation.

O2-Independent H2O2 Production via Water-Polymer Contact Electrification

Hydrogen peroxide (H2O2), as a critical green chemical, has received immense attention in energy and environmental fields. The ability to produce H2O2 in earth-abundant water without relying on low solubility oxygen would be a sustainable and potentially economic process, applicable even to anaerobic microenvironments, such as groundwater treatment. However, the direct water to H2O2 process is currently hindered by low selectivity and low production rates. Herein, we report that poly(tetrafluoroethylene) (PTFE), a commonly used inert polymer, can act as an efficient triboelectric catalyst for H2O2 generation. For example, a high H2O2 production rate of 24.8 mmol gcat-1 h-1 at a dosage of 0.01 g/L PTFE was achieved under the condition of pure water, ambient atmosphere, and no sacrificial agents, which exceeds the performance of state-of-the-art aqueous H2O2 powder catalysts. Electron spin resonance and isotope experiments provide strong evidence that water-PTFE tribocatalysis can directly oxidize water to produce H2O2 under both anaerobic and aerobic conditions, albeit with different synthetic pathways. This study demonstrates a potential strategy for green and effective tribocatalytic H2O2 production that may be particularly useful toward environmental applications.

Designed Local Electric Fields-Promising Tools for Enzyme Engineering

Designing efficient catalysts is one of the ultimate goals of chemists. In this Perspective, we discuss how local electric fields (LEFs) can be exploited to improve the catalytic performance of supramolecular catalysts, such as enzymes. More specifically, this Perspective starts by laying out the fundamentals of how local electric fields affect chemical reactivity and review the computational tools available to study electric fields in various settings. Subsequently, the advances made so far in optimizing enzymatic electric fields through targeted mutations are discussed critically and concisely. The Perspective ends with an outlook on some anticipated evolutions of the field in the near future. Among others, we offer some pointers on how the recent data science/machine learning revolution, engulfing all science disciplines, could potentially provide robust and principled tools to facilitate rapid inference of electric field effects, as well as the translation between optimal electrostatic environments and corresponding chemical modifications.

Water Microdroplets-Initiated Methane Oxidation

The special redox reactivity of water microdroplets causes "mild ignition" of methane gas to form methane oxygenates. The C(sp3)-H bond of methane can be activated by the hydroxyl radical (OH·) or the hydrogen radical (H·) across the air-water interface (AWI) of microdroplets to generate the methyl radical (CH3·). Once CH3· is formed, it undergoes free-radical reactions with O2 in the air, excessive OH· and H· across the AWI, and H2O2 present at the AWI and generated CH3· itself to produce methanol and other species. Production of the methanol and other oxygenates was confirmed by gas chromatography, mass spectrometry, and 1H- and 13C-nuclear magnetic resonance. Formic acid, acetic acid, ethanol, carbon dioxide, and methyl peroxide were also detected as methane oxidation byproducts. This water microdroplet-initiated oxidation process can be further enhanced under ultrasonication to yield 2.66 ± 0.77 mM methanol conversion from the methane gas in a single spray run for 30 min, with a selectivity of 19.2% compared with all other oxygenated species.

Is Reaction Acceleration of Microdroplet Chemistry Favorable to Controlling the Enantioselectivity?

Microdroplet chemistry has been proven to amazingly accelerate many chemical and biological reactions in the past 2 decades. Current microdroplet accelerated reactions are predominantly symmetric synthetic but minorly asymmetric synthetic reactions, where stereoselectivity is scarcely concerned. This study selected unimolecular and bimolecular reactions, multicomponent Passerini reactions, and enzymatic ketone reduction as the model reactions to illustrate whether reaction acceleration of microdroplet chemistry is favorable to retaining a chiral center and controlling the enantioselectivity or not. The results illustrated that microdroplet chemistry did not disrupt pre-existing stereogenic centers in chiral starting materials during reactions but did harm to stereospecificity in asymmetric catalysis by chiral catalysts and chiral organic ligands with the exclusion of enzymatic reactions. Our preliminary study reminds us of more cautions to the product enantioselectivity when conducting asymmetric catalysis in microdroplets. We also hope this study may promote more valuable further research on the stereoselectivity of microdroplet chemistry.

One-step Formation of Urea from Carbon Dioxide and Nitrogen Using Water Microdroplets

Water (H2O) microdroplets are sprayed onto a graphite mesh covered with a CuBi2O4 coating using a 1:1 mixture of N2 and CO2 as the nebulizing gas. The resulting microdroplets contain urea [CO(NH2)2] as detected by both mass spectrometry and 13C nuclear magnetic resonance. This gas-liquid-solid heterogeneous catalytic system synthesizes urea in one step on the 0.1 ms time scale. The conversion rate reaches 2.7 mmol g-1 h-1 at 25 °C and 12.3 mmol g-1 h-1 at 65 °C, with no external voltage applied. Water microdroplets serve as the hydrogen source and the electron transfer medium for N2 and CO2 in contact with CuBi2O4. Water-gas and water-solid contact electrification are speculated to drive the reaction process. This strategy couples N2 fixation and CO2 utilization in an ecofriendly process to produce urea, converting a greenhouse gas into a value-added product.

Mechanism for Generating H2 O2 at Water-Solid Interface by Contact-Electrification

The recent intensification of the study of contact-electrification at water-solid interfaces and its role in physicochemical processes lead to the realization that electron transfers during water-solid contact-electrification can drive chemical reactions. This mechanism, named contact-electro-catalysis (CEC), allows chemically inert fluorinated polymers to act like single electrode electrochemical systems. This study shows hydrogen peroxide (H2 O2 ) is generated from air and deionized water, by ultrasound driven CEC, using fluorinated ethylene propylene (FEP) as the catalyst. For a mass ratio of catalyst to solution of 1:10000, at 20 °C, the kinetic rate of H2 O2 evolution reaches 58.87 mmol L-1  gcat -1  h-1 . Electron paramagnetic resonance (EPR) shows electrons are emitted in the solution by the charged FEP, during ultrasonication. EPR and isotope labelling experiments show H2 O2 is formed from hydroxyl radicals (HO• ) or two superoxide radicals (O2 •- ) generated by CEC. Finally, it is traditionally believed such radicals migrate in the solution by Brownian diffusion prior to reactions. However, ab-initio molecular dynamic calculations reveal the radicals can react by exchanging protons and electrons through the hydrogen bonds network of water, i.e., owing to the Grotthuss mechanism. This mechanism can be relevant to other systems, artificial or natural, generating H2 O2 from air and water.

Size-Dependent Sigmoidal Reaction Kinetics for Pyruvic Acid Condensation at the Air-Water Interface in Aqueous Microdroplets

The chemistry of pyruvic acid (PA) under thermal dark conditions is limited in bulk solutions, but in microdroplets it is shown to readily occur. Utilizing in situ micro-Raman spectroscopy as a probe, we investigated the chemistry of PA within aqueous microdroplets in a relative humidity- and temperature-controlled environmental cell. We found that PA undergoes a condensation reaction to yield mostly zymonic acid. Interestingly, the reaction follows a size-dependent sigmoidal kinetic profile, i.e., an induction period followed by reaction and then completion. The induction time is linearly proportional to the surface area (R2), and the maximum apparent reaction rate is proportional to the surface-to-volume ratio (1/R), showing that both the induction and reaction occur at the air-water interface. Furthermore, the droplet size is shown to be dynamic due to changes in droplet composition and re-equilibration with the relative humidity within the environmental cell as the reaction proceeds. Overall, the size-dependent sigmoidal kinetics, shown for the first time in microdroplets, demonstrates the complexity of the reaction mechanism and the importance of the air-water interface in the pyruvic acid condensation reaction.

Hydrocarbon Degradation by Contact with Anoxic Water Microdroplets

Oils are hydrophobic, but their degradation is frequently found to be accelerated in the presence of water microdroplets. The direct chemical consequences of water-oil contact have long been overlooked. We show that aqueous microdroplets in emulsified water-hexadecane (C16H34) mixtures can spontaneously produce CO2, •H, H2, and short-chain hydrocarbons (mainly C1 and C2) as detected by gas chromatography, electron paramagnetic resonance spectroscopy, and mass spectrometry. This reaction results from contact electrification at the water-oil microdroplet interface, in which reactive oxygen species are produced, such as hydrated hydroxyl radicals and hydrogen peroxide. We also find that the H2 originates from the water microdroplet and not the hydrocarbon it contacts. These observations highlight the potential of interfacial contact electrification to produce new chemistry.

Valence Bond Theory Allows a Generalized Description of Hydrogen Bonding

This paper describes the nature of the hydrogen bond (HB), B:---H-A, using valence bond theory (VBT). Our analysis shows that the most important HB interactions are polarization and charge transfer, and their corresponding sum displays a pattern that is identical for a variety of energy decomposition analysis (EDA) methods. Furthermore, the sum terms obtained with the different EDA methods correlate linearly with the corresponding VB quantities. The VBT analysis demonstrates that the total covalent-ionic resonance energy (RECS) of the HB portion (B---H in B:---H-A) correlates linearly with the dissociation energy of the HB, ΔEdiss. In principle, therefore, RECS(HB) can be determined by experiment. The VBT wavefunction reveals that the contributions of ionic structures to the HB increase the positive charge on the hydrogen of the corresponding external/free O-H bonds in, for example, the water dimer compared with a free water molecule. This increases the electric field of the external O-H bonds of water clusters and contributes to bringing about catalysis of reactions by water droplets and in water-hydrophobic interfaces.

Tribochemically Controlled Atom Transfer Radical Polymerization Enabled by Contact Electrification

Traditional mechanochemically controlled reversible-deactivation radical polymerization (RDRP) utilizes ultrasound or ball milling to regenerate activators, which induce side reactions because of the high-energy and high-frequency stimuli. Here, we propose a facile approach for tribochemically controlled atom transfer radical polymerization (tribo-ATRP) that relies on contact-electro-catalysis (CEC) between titanium oxide (TiO2 ) particles and CuBr2 /tris(2-pyridylmethylamine (TPMA), without any high-energy input. Under the friction induced by stirring, the TiO2 particles are electrified, continuously reducing CuBr2 /TPMA into CuBr/TPMA, thereby conversing alkyl halides into active radicals to start ATRP. In addition, the effect of friction on the reaction was elucidated by theoretical simulation. The results indicated that increasing the frequency could reduce the energy barrier for the electron transfer from TiO2 particles to CuBr2 /TPMA. In this study, the design of tribo-ATRP was successfully achieved, enabling CEC (ca. 10 Hz) access to a variety of polymers with predetermined molecular weights, low dispersity, and high chain-end fidelity.

One-Step, Catalyst-Free Formation of Phenol from Benzoic Acid Using Water Microdroplets

Benzoic acid dissolved in water is electrosprayed (-4 kV) by using nitrogen gas at a pressure of 120 psi to form ∼10 μm diameter microdroplets. Analysis with mass spectrometry (MS) and tandem mass spectrometry (MS2) of the resulting microdroplets shows the direct formation of phenol via decarboxylation without any catalyst or added reagents. This process represents an ecofriendly, environmentally benign method for producing phenol and related aromatic alcohols from their corresponding aromatic acids. The mechanism of this transformation was unambiguously characterized using mass spectrometry, radical trapping, and 18O labeling.

Influence of Wettability and Geometry on Contact Electrification between Nonionic Insulators

Contact electrification is an interfacial process in which two surfaces exchange electrical charges when they are in contact with one another. Consequently, the surfaces may gain opposite polarity, inducing an electrostatic attraction. Therefore, this principle can be exploited to generate electricity, which has been precisely done in triboelectric nanogenerators (TENGs) over the last decades. The details of the underlying mechanisms are still ill-understood, especially the influence of relative humidity (RH). Using the colloidal probe technique, we convincingly show that water plays an important role in the charge exchange process when two distinct insulators with different wettability are contacted and separated in <1 s at ambient conditions. The charging process is faster, and more charge is acquired with increasing relative humidity, also beyond RH = 40% (at which TENGs have their maximum power generation), due to the geometrical asymmetry (curved colloid surface vs planar substrate) introduced in the system. In addition, the charging time constant is determined, which is found to decrease with increasing relative humidity. Altogether, the current study adds to our understanding of how humidity levels affect the charging process between two solid surfaces, which is even enhanced up to RH = 90% as long as the curved surface is hydrophilic, paving the way for designing novel and more efficient TENGs, eco-energy harvesting devices which utilize water and solid charge interaction mechanism, self-powered sensors, and tribotronics.

Silica particles convert thiol-containing molecules to disulfides

Synthetic amorphous silica is a common food additive and a popular cosmetic ingredient. Mesoporous silica particles are also widely studied for their potential use in drug delivery and imaging applications because of their unique properties, such as tunable pore sizes, large surfaces areas, and assumed biocompatibility. Such a nanomaterial, when consisting of pure silicon dioxide, is generally considered to be chemically inert, but in this study, we showed that oxidation yields for different compounds were facilitated by simply incubating aqueous solutions with pure silica particles. Three thiol-containing molecules, L-cysteine, glutathione, and D-penicillamine, were studied separately, and it was found that more than 95% of oxidation happened after incubating any of these compounds with mesoporous silica particles in the dark for a day at room temperature. Oxidation increased over incubation time, and more oxidation was found for particles having larger surface areas. For nonporous silica particles at submicron ranges, yields of oxidation were different based on the structures of molecules, correlating with steric hindrance while accessing surfaces. We propose that the silyloxy radical (SiO•) on silica surfaces is what facilitates oxidation. Density functional theory calculations were conducted for total energy changes for reactions between different aqueous species and silicon dioxide surfaces. These calculations identified two most plausible pathways of the lowest energy to generate SiO• radicals from water radical cations H2O•+ and hydroxyl radicals •OH, previously known to exist at water interfaces.

Size-dependent charge transfer between water microdroplets

Contact electrification (CE) in water has attracted much attention, owing to its potential impacts on the chemical reactions, such as the recent discovery of spontaneous generation of hydrogen peroxide (H2O2) in water microdroplets. However, current studies focus on the CE of bulk water, the measurement of CE between micrometer-size water droplets is a challenge and its mechanism still remains ambiguous. Here, a method for quantifying the amount of charge carried by the water microdroplets produced by ultrasonic atomization is proposed. In the method, the motions of water microdroplets in a uniform electric field are observed and the electrostatic forces on the microdroplets are calculated based on the moving speed of the microdroplets. It is revealed that the charge transfer between water microdroplets is size-dependent. The large microdroplets tend to be positively charged while the small microdroplets tend to receive negative charges, implying that the negative charges transfer from large microdroplets to the small microdroplets during ultrasonic atomization. Further, a theoretical model for microdroplets charging is proposed, in which the curvature-induced surface potential/energy difference is suggested to be responsible for the charge transfer between microdroplets. The findings show that the electric field strength between two microdroplets with opposite charges during separation is strong enough to convert OH‒ to OH*, providing evidence for the CE-induced spontaneous generation of H2O2 in water microdroplets.

Contact between water vapor and silicate surface causes abiotic formation of reactive oxygen species in an anoxic atmosphere

Spontaneous generation of reactive oxygen species (ROS) in aqueous microdroplets or at a water vapor-silicate interface is a new source of redox chemistry. However, such generation occurs with difficulty in liquid water having a large ionic strength. We report that ROS is spontaneously produced when water vapor contacts hydrogen-bonded hydroxyl groups on a silicate surface. The evolution of hydrogen-bonded species such as hydroxyl groups was investigated by using two-dimensional, time-resolved FT-IR spectroscopy. The participation of water vapor in ROS generation is confirmed by investigating the reaction of D2O vapor and hydroxyl groups on a silicate surface. We propose a reaction pathway for ROS generation based on the change of the hydrogen-bonding network and corresponding electron transfer onto the silicate surface in the water vapor-solid contact process. Our observations suggest that ROS production from water vapor-silicate contact electrification could have contributed to oxidation during the Archean Eon before the Great Oxidation Event.

The Spontaneous Electron-Mediated Redox Processes on Sprayed Water Microdroplets

Water is considered as an inert environment for the dispersion of many chemical systems. However, by simply spraying bulk water into microsized droplets, the water microdroplets have been shown to possess a large plethora of unique properties, including the ability to accelerate chemical reactions by several orders of magnitude compared to the same reactions in bulk water, and/or to trigger spontaneous reactions that cannot occur in bulk water. A high electric field (∼10⁹ V/m) at the air-water interface of microdroplets has been postulated to be the probable cause of the unique chemistries. This high field can even oxidize electrons out of hydroxide ions or other closed-shell molecules dissolved in water, forming radicals and electrons. Subsequently, the electrons can trigger further reduction processes. In this Perspective, by showing a large number of such electron-mediated redox reactions, and by studying the kinetics of these reactions, we opine that the redox reactions on sprayed water microdroplets are essentially processes using electrons as the charge carriers. The potential impacts of the redox capability of microdroplets are also discussed in a larger context of synthetic chemistry and atmospheric chemistry.

Humic acids alleviate aflatoxin B1-induced hepatic injury by reprogramming gut microbiota and absorbing toxin

Aflatoxin B1 (AFB1) is a hepatotoxic fungal metabolite that is widely present in food and can cause liver cancer. As a potential detoxifier, naturally occurring humic acids (HAs) may be able to reduce inflammation and restructure the gut microbiota composition; however, little is known about the mechanism of HAs detoxification as applied to liver cells. In this study, HAs treatment alleviated AFB1-induced liver cell swelling and the infiltration of inflammatory cells. HAs treatment also reinstated various enzyme levels in the liver disturbed by AFB1 and substantially alleviated AFB1-caused oxidative stress and inflammatory responses by enhancing immune functions in mice. Moreover, HAs increased the length of the small intestinal and villus height to restore intestinal permeability, which is impaired by AFB1. In addition, HAs reconstructed the gut microbiota, increasing the relative abundance of Desulfovibrio, Odoribacter, and Alistipes. In vitro and in vivo assays demonstrated that HAs could efficiently remove AFB1 by absorbing the toxin. Therefore, HAs treatment can ameliorate AFB1-induced hepatic injury by enhancing gut barrier function, regulating gut microbiota, and adsorbing toxin.

Water Reactivity in Electrified Interfaces: The Simultaneous Production of Electricity, Hydrogen, and Hydrogen Peroxide at Room Temperature

Hygroelectric cells deliver hydrogen, hydrogen peroxide, and electric current simultaneously at room temperature from liquid water or vapor. Different cell arrangements allowed the electrical measurements and the detection and measurement of the reaction products by two methods each. Thermodynamic analysis shows that water dehydrogenation is a non-spontaneous reaction under standard conditions, but it can occur within an open, non-electroneutral system, thus supporting the experimental results. That is a new example of chemical reactivity modification in charged interfaces, analogous to the hydrogen peroxide formation in charged aqueous aerosol droplets. Extension of the experimental methods and the thermodynamic analysis used in this work may allow the prediction of interesting new chemical reactions that are otherwise unexpected. On the other hand, this adds a new facet to the complex behavior of interfaces. Hygroelectric cells shown in this work are built from commodity materials, using standard laboratory or industrial processes that are easily scaled up. Thus, hygroelectricity may eventually become a source of energy and valuable chemicals.

One-Step Formation of Pharmaceuticals Having a Phenylacetic Acid Core Using Water Microdroplets

The properties of water microdroplets strikingly differ from bulk water. Using room-temperature water microdroplets, we find that toluene can react with CO₂ to form phenylacetic acid in one step without any catalyst with negative high voltage applied at the sprayer source. The chemical components of these microdroplets are identified by mass spectrometry, and product structures are confirmed by tandem mass spectrometry. In this manner, we generate three drug molecules in a single step: 4-aminophenylacetic acid (epithelial peptide transporter PepT1 inhibitor), 3,4-dihydroxyphenylacetic acid (dopamine metabolite neurotransmitter), and phenylacetic acid (sodium salt form; treatment of urea cycle disorder). Mechanistic studies show that benzyl radicals formed from hydroxyl radicals at the water microdroplet interface drive these carboxylation reactions. This water microdroplet chemistry is general, allowing activation and subsequent carboxylation of aryl α-C-H groups.

Experimental and Thermodynamic Viewpoints on Claims of a Spontaneous H2O2 Formation at the Air-Water Interface

Recent claims of the spontaneous H₂O₂ formation at the air-water interface of water microdroplets have sparked debates on its feasibility. New results from different research groups have provided more insight into these claims, but conclusive proofs are still far from realized. In this Perspective, thermodynamic viewpoints, potential experiments, and theoretical approaches are presented as references for future studies. We suggest that future work should seek for H₂ byproduct as indirect evidence to confirm the feasibility of this phenomenon. Examining potential energy surfaces for H₂O₂ formation reaction when moving from the bulk to the interface under the influence of the local electric fields is also critical to establish this phenomenon.

Acid-induced nitrite reduction of nonheme iron(ii)-nitrite: mimicking biological Fe-NiR reactions

Nitrite reductase (NiR) catalyzes nitrite (NO₂ ^-) to nitric oxide (NO) transformation in the presence of an acid (H⁺ ions/pH) and serves as a critical step in NO biosynthesis. In addition to the NiR enzyme, NO synthases (NOSs) participate in NO production. The chemistry involved in the catalytic reduction of NO₂ ^-, in the presence of H⁺, generates NO with a H₂O molecule utilizing two H⁺ + one electron from cytochromes and is believed to be affected by the pH. Here, to understand the effect of H⁺ ions on NO₂ ^- reduction, we report the acid-induced NO₂ ^- reduction chemistry of a nonheme Fe^II-nitrito complex, [(12TMC)Fe^II(NO₂ ^-)]⁺ (Fe^II-NO₂ ^-, 2), with variable amounts of H⁺. Fe^II-NO₂ ^- upon reaction with one-equiv. of acid (H⁺) generates [(12TMC)Fe(NO)]²⁺, {FeNO}⁷ (3) with H₂O₂ rather than H₂O. However, the amount of H₂O₂ decreases with increasing equivalents of H⁺ and entirely disappears when H⁺ reaches ≅ two-equiv. and shows H₂O formation. Furthermore, we have spectroscopically characterized and followed the formation of H₂O₂ (H⁺ = one-equiv.) and H₂O (H⁺ ≅ two-equiv.) and explained why bio-driven NiR reactions end with NO and H₂O. Mechanistic investigations, using ¹⁵N-labeled-¹⁵NO₂ ^- and ²H-labeled-CF₃SO₃D (D⁺ source), revealed that the N atom in the {Fe^14/15NO}⁷ is derived from the NO₂ ^- ligand and the H atom in H₂O or H₂O₂ is derived from the H⁺ source, respectively.

Fluidics for energy harvesting: from nano to milli scales

A large amount of untapped energy sources surrounds us. In this review, we summarize recent works of water-based energy harvesting systems with operation scales ranging from miniature systems to large scale attempts. We focus particularly on the triboelectric energy, which is produced when a liquid and a solid come into contact, and on the osmotic energy, which is released when salt water and fresh water are mixed. For both techniques we display the state of the art understanding (including electrical charge separation, electro-osmotic currents and induced currents) and the developed devices. A critical discussion of present works confirms the significant progress of these water-based energy harvesting systems in all scales. However, further efforts in efficiency and performance amelioration are expected for these technologies to accelerate the industrialization and commercialization procedure.

How Can Static and Oscillating Electric Fields Serve in Decomposing Alzheimer's and Other Senile Plaques?

Alzheimer's disease is one of the most common neurodegenerative conditions, which are ascribed to extracellular accumulation of β-amyloid peptides into plaques. This phenomenon seems to typify other related neurodegenerative diseases. The present study uses classical molecular-dynamics simulations to decipher the aggregation-disintegration behavior of β-amyloid peptide plaques in the presence of static and oscillating oriented external electric fields (OEEFs). A long-term disintegration of such plaques is highly desirable since this may improve the prospects of therapeutic treatments of Alzheimer's disease and of other neurodegenerative diseases typified by senile plaques. Our study illustrates the spontaneous aggregation of the β-amyloid, its prevention and breakdown when OEEF is applied, and the fate of the broken aggregate when the OEEF is removed. Notably, we demonstrate that the usage of an oscillating OEEF on β-amyloid aggregates appears to lead to an irreversible disintegration. Insight is provided into the root causes of the various modes of aggregation, as well as into the different fates of OEEF-induced disintegration in oscillating vs static fields. Finally, our simulation results are compared to the well-established TTFields and the Deep Brain Stimulation (DBS) therapies, which are currently used options for treatments of Alzheimer's disease and other related neurodegenerative diseases.

Spontaneous Reduction of Transition Metal Ions by One Electron in Water Microdroplets and the Atmospheric Implications

Freshman chemistry teaches that Fe³⁺ and Cu²⁺ ions are stable in water solutions, but their reduced forms, Fe²⁺ and Cu⁺, cannot exist in water as the major oxidation state due to the fast oxidation by O₂ and/or disproportionation. Contrary to these well-known facts, significant fractions of dissolved Fe and Cu species exist in their reduced oxidation states in atmospheric water such as deliquesced aerosols, clouds, and fog droplets. Current knowledge attributes these phenomena to the stabilization of the lower oxidation states by the complexation of ligands and the various photochemical or thermal pathways that can reduce the higher oxidation states. In this study, by spraying the water solutions of transition metal ions into microdroplets, we show the results of the spontaneous reduction of ligated Fe(III) and Cu(II) species into Fe(II) and Cu(I) species, presenting a previously unknown source of reduced transition metal ions in atmospheric water. It is the spontaneously generated electrons in water microdroplets that are responsible for the reduction. Control experiments in the atmosphere and in a glove box filled with precisely controlled gaseous contents reveal that O₂, CO₂, and NO₂ are the major competitors for the electrons, forming O₂^-, HCO₂^-, and NO₂^-, respectively. Taking these findings together, we opine that microdroplet chemistry might play significant but previously underestimated roles in atmospheric redox chemistry.

Catalyst-Free Decarboxylative Amination of Carboxylic Acids in Water Microdroplets

Previous studies have shown that hydroxyl radicals can be formed at the water-gas surface of water microdroplets. We report the use of in situ generated hydroxyl radicals to carry out an organic transformation in one step, namely, the formation of anilines from aryl acids as well as both ammonia and primary/secondary amines via decarboxylation. Benzoic acids and amines are dissolved in water, and the solution is sprayed to form microdroplets whose chemical contents are analyzed mass spectrometrically. All intermediates and products are determined using mass spectrometry (MS) as well as in some cases tandem mass spectrometry (MS²). These results support the following reaction mechanism: NR₂OH, formed via reaction of the amine with •OH, reacts with benzoic acid to form an isocyanate via a Lossen rearrangement. Hydrolysis followed by liberation of CO₂ then delivers the aniline product. Notably, the scope of this transformation includes a variety of amines and aromatic acids and enables their conversion into aniline and N-substituted anilines, all in a single step. Additionally, this reaction occurs at room temperature and does not require metal catalysts or organic solvents.

Ozone-Facilitated Formation of Uranyl Peroxide in Humid Conditions

Metaschoepite, [(UO₂)₈O₂(OH)₁₂](H₂O)₁₀, maintained in a high relative humidity (RH) environment with air initially transformed into an intermediate phase that subsequently was replaced by the peroxide phase studtite, [(UO₂)(O₂)(H₂O)₂](H₂O)₂, over the course of 42 days, as observed using Raman and infrared spectroscopy and powder X-ray diffraction. Addition of atmospheric ozone vastly increased the rate and extent of the transformation to studtite but only in a high-RH atmosphere. Owing to its strong affinity for peroxide, uranyl reacted with hydrogen peroxide as it formed and precipitated stable studtite. In this work, we provide a previously unidentified source of hydrogen peroxide and make a case for the re-examination of storage systems where the consequences of atmospheric ozone are not considered.