Effects of localised, low-voltage pulsed electric fields on the development and inhibition of Pseudomonas aeruginosa biofilms

Environmental pollution removal using electrostimulation of microorganisms by alternative current

The entrance of some toxic and hazardous chemical agents such as antibiotics, pesticides, and herbicides into the environment can cause various problems to human health and the environment. In recent years, researchers have considered the use of electrostimulation in the processes of microbial metabolism and biological systems for the treatment of pollutants in the environment. Although several electrostimulation reports have been presented for pollutant removal, little attention has been paid to alternative current (AC) biostimulation. This study presents a systematic review of microbial electrostimulation using bioelectrochemical systems supplied with AC. The utilization of alternating current bioelectrochemical systems (ACBESs) has some advantages such as the provide of appropriate active biofilms in the electrodes due to the cyclical nature of the current and energy transfer in an appropriate manner on the electrode surfaces. Moreover, the ACBESs can reduce hydraulic time (HRT) under optimal conditions and reduce the cost of converting electricity using AC. In microbial electrostimulation, amplitude (AMPL), waveform, C/N, and current have a significant effect on increasing the removal efficiency of the pollutants. The obtained results of the meta-analysis illustrated that various pollutants such as phenol, antibiotics, and nitrate have been removed in an acceptable range of 96% using the ACBESs. Therefore, microbial electrostimulation using AC is a promising technology for the decomposition and removal of various pollutants. Moreover, the ACBESs could provide new opportunities for promoting various bioelectrochemical systems (BESs) for the production of hydrogen or methane.

Comparison of the efficacy of physical and chemical strategies for the inactivation of biofilm cells of foodborne pathogens

Biofilm formation is a strategy in which microorganisms generate a matrix of extracellular polymeric substances to increase survival under harsh conditions. The efficacy of sanitization processes is lowered when biofilms form, in particular on industrial devices. While various traditional and emerging technologies have been explored for the eradication of biofilms, cell resistance under a range of environmental conditions renders evaluation of the efficacy of control challenging. This review aimed to: (1) classify biofilm control measures into chemical, physical, and combination methods, (2) discuss mechanisms underlying inactivation by each method, and (3) summarize the reduction of biofilm cells after each treatment. The review is expected to be useful for future experimental studies and help to guide the establishment of biofilm control strategies in the food industry.

Electric Potential Induced Prevention and Removal of an Algal Biofoulant from Planar SERS Substrates

Ulva zoospores are widespread marine macroalgae and a common organism found in biofouling communities due to their strong adhesive properties and quick settlement times. Using Ulva as a model organism, a strategy is presented where direct-current (DC) electric potentials are applied in conjunction with surface-enhanced Raman spectroscopy (SERS) to characterize, remove, and prevent Ulva from forming a biofilm on gold-capped nanopillar SERS substrates. Experiments were conducted within a poly(tetrafluoroethylene) (PTFE) flow channel device where the SERS substrates were used as an electrode. Ulva density, determined in situ by SERS and ex situ by electron and fluorescence microscopy, decreased under successively increasing low negative potentials up to -1.0 V. The presence of damaged Ulva suggests that the applied potential led to spore rupture. At the highest negative applied potential (-1.0 V), microparticles containing copper, which is known for its antimicrobial properties, were associated with Ulva on the SERS substrate and the lowest Ulva density was observed. These findings indicate that (1) SERS can be employed to study biofilm formation on nanostructured metal surfaces and (2) applying low-voltage electric potentials may be used to control Ulva biofouling on SERS marine sensors.

Reduction of biofilm accumulation by constant and alternating potentials in static and dynamic field experiments

The application of electric fields to conductive coatings is an environmentally friendly way to reduce biofilm formation. In particular alternating potentials (APs) have received increasing attention in recent studies. Here, an electrochemical rotating disk setup for dynamic field exposure experiments was developed to study how APs alter the attachment of fouling organisms in a multispecies ocean environment. A specific focus of the device design was proper integration of the potentiostat in the strongly corroding saltwater environment. The effect of APs on the accumulation of fouling organisms in short term field exposures was studied. Potentials on conductive gold surfaces were periodically switched between -0.3 V and 0.3 V or between -0.8 V and 0.6 V at a frequency of 0.5 Hz. APs were capable of significantly reducing the attachment of marine fouling organisms compared with the conductive samples immersed at open circuit potentials.

Rotating Magnetic Field Increases β-Lactam Antibiotic Susceptibility of Methicillin-Resistant Staphylococcus aureus Strains

Methicillin-resistant strains of Staphylococcus aureus (MRSA) have developed resistance to most β-lactam antibiotics and have become a global health issue. In this work, we analyzed the impact of a rotating magnetic field (RMF) of well-defined and strictly controlled characteristics coupled with β-lactam antibiotics against a total of 28 methicillin-resistant and sensitive S. aureus strains. The results indicate that the application of RMF combined with β-lactam antibiotics correlated with favorable changes in growth inhibition zones or in minimal inhibitory concentrations of the antibiotics compared to controls unexposed to RMF. Fluorescence microscopy indicated a drop in the relative number of cells with intact cell walls after exposure to RMF. These findings were additionally supported by the use of SEM and TEM microscopy, which revealed morphological alterations of RMF-exposed cells manifested by change of shape, drop in cell wall density and cytoplasm condensation. The obtained results indicate that the originally limited impact of β-lactam antibiotics in MRSA is boosted by the disturbances caused by RMF in the bacterial cell walls. Taking into account the high clinical need for new therapeutic options, effective against MRSA, the data presented in this study have high developmental potential and could serve as a basis for new treatment options for MRSA infections.

Antimicrobial photodynamic therapy (aPDT) for biofilm treatments. Possible synergy between aPDT and pulsed electric fields

Currently, microbial biofilms have been the cause of a wide variety of infections in the human body, reaching 80% of all bacterial and fungal infections. The biofilms present specific properties that increase the resistance to antimicrobial treatments. Thus, the development of new approaches is urgent, and antimicrobial photodynamic therapy (aPDT) has been shown as a promising candidate. aPDT involves a synergic association of a photosensitizer (PS), molecular oxygen and visible light, producing highly reactive oxygen species (ROS) that cause the oxidation of several cellular components. This therapy attacks many components of the biofilm, including proteins, lipids, and nucleic acids present within the biofilm matrix; causing inhibition even in the cells that are inside the extracellular polymeric substance (EPS). Recent advances in designing new PSs to increase the production of ROS and the combination of aPDT with other therapies, especially pulsed electric fields (PEF), have contributed to enhanced biofilm inhibition. The PEF has proven to have antimicrobial effect once it is known that extensive chemical reactions occur when electric fields are applied. This type of treatment kills microorganisms not only due to membrane rupture but also due to the formation of reactive compounds including free oxygen, hydrogen, hydroxyl and hydroperoxyl radicals. So, this review aims to show the progress of aPDT and PEF against the biofilms, suggesting that the association of both methods can potentiate their effects and overcome biofilm infections.

Control of Marine Bacteria and Diatom Biofouling by Constant and Alternating Potentials

The application of electrochemical potentials to surfaces is an easy and direct way to alter surface charge density, the structure of the electrochemical double layer, and the presence of electrochemically activated species. On such electrified interfaces the formation of biofilms is reduced. Here we investigate how applied potentials alter the colonization of surfaces by the marine bacterium Cobetia marina and the marine diatom Navicula perminuta. Different constant potentials between -0.8 and 0.6 V as well as regular switching between two potentials were investigated, and their influence on the attachment of the two biofilm-forming microorganisms on gold-coated working electrodes was quantified. Reduced bacteria and diatom attachment were found when negative potentials and alternating potentials were applied. The results are discussed on the basis of the electrochemical processes occurring at the working electrode in artificial seawater as revealed by cyclic voltammetry.

Pathogens electrogenicity as a tool for in-situ metabolic activity monitoring and drug assessment in biofilms

Concerns regarding increased antibiotic resistance arising from the emergent properties of biofilms have spurred interest in the discovery of novel antibiotic agents and techniques to directly estimate metabolic activity in biofilms. Although a number of methods have been developed to quantify biofilm formation, real-time quantitative assessment of metabolic activity in label-free biofilms remains a challenge. Production of electrical current via extracellular electron transport (EET) has recently been found in pathogens and appears to correlate with their metabolic activity. Accordingly, monitoring the production of electrical currents as an indicator of cellular metabolic activity in biofilms represents a new direction for research aiming to assess and screen the effects of antimicrobials on biofilm activity. In this article, we reviewed EET-capable pathogens and the methods to monitor biofilm activity to discuss advantages of using the capability of pathogens to produce electrical currents and effective combination of these methods. Moreover, we discussed EET mechanisms by pathogenic and environmental bacteria and open questions for the physiological roles of EET in pathogen's biofilm. The present limitations and possible future directions of in situ biofilm metabolic activity assessment for large-scale screening of antimicrobials are also discussed.

Using electromagnetic fields to inhibit biofouling and scaling in biogas slurry drip irrigation emitters

Reusing biogas slurry (BS) in agricultural drip irrigation systems may provide a solution to deal with the adverse environmental impacts of applying BS. Biofouling and scaling are two leading issues in drip irrigation emitters. This study investigated a practice that applied electromagnetic fields (EMFs) to control biofilms and scales. The bacterial communities and mineral precipitations in the clogging substances of emitters were determined. Results showed that EMFs inhibited the growth of microbes, and influenced BS physicochemical parameters. Consequently, EMFs shifted the bacterial communities with reduced diversities. Network analyses revealed that bacterial species under EMFs treatments showed lower average connectivities and simpler interactions, which were responsible for the decreases of extracellular polymers substances (EPS). Moreover, EMFs treatments not only reduced the carbonates in emitters, but also prevented the depositions of phosphates, silicates, and quartzes. EMFs also had impacts on the lattice parameters and crystal volumes of carbonates. In addition, the changes in bacterial communities and EPS contents were associated with the reductions of various minerals. Accordingly, EMFs effectively mitigated biofilms and scales with the fixed clogging substances reduced by 29.1-53.8 %. These findings demonstrated that applying EMFs is an effective anti-biofouling and anti-scaling treatment with potential applications in BS irrigation systems.

A review of bacterial biofilm control by physical strategies

Biofilms are multicellular communities of microorganisms held together by a self-produced extracellular matrix, which contribute to hygiene problems in the food and medical fields. Both spoilage and pathogenic bacteria that grow in the complex structure of biofilm are more resistant to harsh environmental conditions and conventional antimicrobial agents. Therefore, it is important to develop eco-friendly preventive methodologies to eliminate biofilms from foods and food contact equipment. The present paper gives an overview of the current physical methods for biofilm control and removal. Current physical strategies adopted for the anti-biofilm treatment mainly focused on use of ultrasound power, electric or magnetic field, plasma, and irradiation. Furthermore, the mechanisms of anti-biofilm action and application of different physical methods are discussed. Physical strategies make it possible to combat biofilm without the use of biocidal agents. The remarkable microbiocidal properties of physical strategies are promising tools for antimicrobial applications.

Selective Inactivation of Pseudomonas aeruginosa and Staphylococcus epidermidis with Pulsed Electric Fields and Antibiotics

Objective: Increasing numbers of multidrug-resistant bacteria make many antibiotics ineffective; therefore, new approaches to combat microbial infections are needed. In addition, antibiotics are not selective-they kill pathogenic organisms as well as organisms that could positively contribute to wound healing (bio flora). Approach: Here we report on selective inactivation of Pseudomonas aeruginosa and Staphylococcus epidermidis, potential pathogens involved in wound infections with pulsed electric fields (PEFs) and antibiotics (mix of penicillin, streptomycin, and nystatin). Results: Using a Taguchi experimental design in vitro, we found that, under similar electric field strengths, the pulse duration is the most important parameter for P. aeruginosa inactivation, followed by the number of pulses and pulse frequency. P. aeruginosa, a potential severe pathogen, is more sensitive than the less pathogenic S. epidermidis to PEF (alone or in combination with antibiotics). Applying 200 pulses with a duration of 60 μs at 2.8 Hz, the minimum electric fields of 308.8 ± 28.3 and 378.4 ± 12.9 V/mm were required to inactive P. aeruginosa and S. epidermidis, respectively. Addition of antibiotics reduced the threshold for minimum electric fields required to inactivate the bacteria. Innovation: This study provides essential information, such as critical electric field parameters for bacteria inactivation, required for developing in vivo treatment and clinical protocols for using PEF for wound healing. Conclusion: A combination of PEFs with antibiotics reduces the electric field threshold required for bacteria disinfection. Such an approach simplifies devices required to disinfect large areas of infected wounds.

The Modular Adaptive Electrotherapy Delivery System (MAEDS): An Electroceutical Approach for Effective Treatment of Wound Infection and Promotion of Healing

Background

Infected wounds are painful and cannot heal, with antibiotics showing reduced efficacy. Appropriate wound electrotherapy may limit incident planktonic and polymicrobial colonization, inhibit biofilm formation and accelerate healing.

Methods

The Modular Adaptive Electrotherapy Delivery System (MAEDS) is a lightweight, flexible, battery-powered disposable bandage which delivers controlled reliable electrotherapy to the wound for up to 7 days. Large full-thickness excisional wounds (6 cm diameter) were created in a porcine model and freshly cultured 0.5 McFarland green fluorescent protein-labeled Pseudomonas aeruginosa evenly applied to the wound bed. Control wounds received standard wound care, Tegaderm HP Transparent Dressing (3 M Health Care, St. Paul, MN, USA) applied in a sterile fashion. Treatment wounds received MAEDS electrotherapy for up to 28 days or until healed. Onboard Bluetooth facilitated remote real-time monitoring of MAEDS function. Dressing changes occurred on postoperative day (POD) 1, 3, 5, 7, 10, 14, 21, and 28. Punch biopsies were taken at the wound margin and center. Bacterial samples were processed to determine infection status.

Results

Acute infected wounds treated with MAEDS electrotherapy were 92% smaller than baseline by POD21. Healing rate was significantly faster (p < 0.01) and infection significantly decreased (p < 0.0001) at POD10, relative to control wounds.

Conclusion

The MAEDS electrotherapy can significantly inhibit infection and enhance healing rate in acute infected wounds.

IGBT-Based Pulsed Electric Fields Generator for Disinfection: Design and In Vitro Studies on Pseudomonas aeruginosa

Irreversible electroporation of cell membrane with pulsed electric fields is an emerging physical method for disinfection that aims to reduce the doses and volumes of used antibiotics for wound healing. Here we report on the design of the IGBT-based pulsed electric field generator that enabled eradication of multidrug resistant Pseudomonas aeruginosa PAO1 on the gel. Using a concentric electric configuration we determined that the lower threshold of the electric field required to kill P. aeruginosa PAO1 was 89.28 ± 12.89 V mm^-1, when 200 square pulses of 300 µs duration are delivered at 3 Hz. These parameters disinfected 38.14 ± 0.79 mm² area around the single needle electrode. This study provides a step towards the design of equipment required for multidrug-resistant bacteria disinfection in patients with pulsed electric fields.

Demonstration of biofilm removal from type 304 stainless steel using pulsed-waveform electropolishing

This article describes an electrochemical method to remove bacterial biofilm from a stainless steel (SS) surface using a potential pulse/reverse pulse technique. This technique employs a periodic waveform that consists of anodic and cathodic pulses. The pulses can effectively strip a thin layer of metal off the SS surface, along with the adherent biofilm, in a saline solution. Not only can the pulses effectively remove biofilm from the SS surface, but they also regenerate the original mirror-like shiny surface. The importance of this electrochemical biofilm removal method is its wide applicability for any types of biofilms. That is, instead of directly removing the biofilm, it removes a very thin layer of the metal under the biofilm. Thus, the removal process is independent to the nature of the biofilms. Furthermore, this electrochemical biofilm removal method is rapid (less than 30 s of potential pulse time) and does not require hazardous chemicals.

Low voltage electric potential as a driving force to hinder biofouling in self-supporting carbon nanotube membranes

This study aimed at evaluating the contribution of low voltage electric field, both alternating (AC) and direct (DC) currents, on the prevention of bacterial attachment and cell inactivation to highly electrically conductive self-supporting carbon nanotubes (CNT) membranes at conditions which encourage biofilm formation. A mutant strain of Pseudomonas putida S12 was used a model bacterium and either capacitive or resistive electrical circuits and two flow regimes, flow-through and cross-flow filtration, were studied. Major emphasis was placed on AC due to its ability of repulsing and inactivating bacteria. AC voltage at 1.5 V, 1 kHz frequency and wave pulse above offset (+0.45) with 100Ω external resistance on the ground side prevented almost completely attachment of bacteria (>98.5%) with concomitant high inactivation (95.3 ± 2.5%) in flow-through regime. AC resulted more effective than DC, both in terms of biofouling reduction compared to cathodic DC and in terms of cell inactivation compared to anodic DC. Although similar trends were observed, a net reduced extent of prevention of bacterial attachment and inactivation was observed in filtration as compared to flow-through regime, which is mainly attributed to the permeate drag force, also supported by theoretical calculations in DC in capacitive mode. Electrochemical impedance spectroscopy analysis suggests a pure resistor behavior in resistance mode compared to involvement of redox reactions in capacitance mode, as source for bacteria detachment and inactivation. Although further optimization is required, electrically polarized CNT membranes offer a viable antibiofouling strategy to hinder biofouling and simplify membrane care during filtration.

Cutaneous wound biofilm and the potential for electrical stimulation in management of the microbiome

Infection contributes significantly to delayed cutaneous wound healing, which impacts patient care. External application of electrical stimulation (ES) has beneficial effects on wound repair and regeneration. The majority of studies to date have explored ES in relation to planktonic microorganisms, yet evidence indicates that bacteria in chronic wounds reside as antibiotic-resistant polymicrobial biofilms, which contribute to impairing wound healing. Culture-independent sequencing techniques have revolutionized our understanding of the skin microbiome and allowed a more accurate determination of microbial taxa and their relative abundance in wounds allowing a greater understanding of the host–microbial interface. Future studies combining the fields of ES, biofilm and microbiome research are necessary to fully elucidate the use of ES in the management of wound infection.

Rotation Disk Process to Assess the Influence of Metals and Voltage on the Growth of Biofilm

Biofilms consist of not only bacteria but also extracellular polymer substrates (EPS). They are groups of microorganisms that adhere to each other on a surface, especially as a result of exposure to water and bacteria. They can pose health risks to humans as they grow in hospital settings that include medical supplies and devices. In a previous study, the researchers discovered that bacteria/biofilm grew well on wetted external latex, male catheters. These results concerned the investigators and encouraged them to find ways for prohibiting the growth of bacteria/biofilm on the male catheters (which are made of natural rubber). They carried out a new study to assess the influence of metals and voltage for the growth of bacteria on these latex samples. For this purpose, a unique Rotation Disk Reactor was used to accelerate biofilm formation on external male catheter samples. This setup included a dip tank containing water and a rotating wheel with the attached latex samples (some of which had single electrodes while others had paired electrodes with applied voltage). The process allowed the samples to become wetted and also exposed them to microorganisms in the ambient air during each revolution of the wheel. The results (as viewed from SEM images) showed that when compared to the control sample, the presence of metals (brass, stainless steel, and silver) was generally effective in preventing bacterial growth. Also the use of voltage (9.5 volt battery) essentially eliminated the appearance of rod shaped bacteria in some of the samples. It can be concluded that the presence of metals significantly reduced bacterial growth on latex and the application of voltage was able to essentially eliminate bacteria, providing appropriate electrode combinations were used.

Nanocarbon-based membrane filtration integrated with electric field driving for effective membrane fouling mitigation

Membrane filtration provides an effective solution for removing pollutants from water but is limited by serious membrane fouling. In this work, an effective approach was used to mitigate membrane fouling by integrating membrane filtration with electropolarization using an electroconductive nanocarbon-based membrane. The electropolarized membrane (EM) by alternating square-wave potentials between +1.0 V and -1.0 V with a pulse width of 60 s exhibited a permeate flux 8.1 times as high as that without electropolarization for filtering feed water containing bacteria, which confirms the ability of the EM to achieve biofouling mitigation. Moreover, the permeate flux of EM was 1.5 times as high as that without electropolarization when filtrating natural organic matter (NOM) from water, and demonstrated good performance in organic fouling mitigation with EM. Furthermore, the EM was also effective for complex fouling mitigation in filtering water containing coexisting bacteria and NOM, and presented an increased flux rate 1.9 times as high as that without electropolarization. The superior fouling mitigation performance of EM was attributed to the synergistic effects of electrostatic repulsion, electrochemical oxidation and electrokinetic behaviors. This work opens an effective avenue for membrane fouling mitigation of water-treatment membrane filtration systems.

Electrokinetic control of bacterial deposition and transport

Microbial biofilms can cause severe problems in technical installations where they may give rise to microbially influenced corrosion and clogging of filters and membranes or even threaten human health, e.g. when they infest water treatment processes. There is, hence, high interest in methods to prevent microbial adhesion as the initial step of biofilm formation. In environmental technology it might be desired to enhance bacterial transport through porous matrices. This motivated us to test the hypothesis that the attractive interaction energy allowing cells to adhere can be counteracted and overcome by the shear force induced by electroosmotic flow (EOF, i.e. the water flow over surfaces exposed to a weak direct current (DC) electric field). Applying EOF of varying strengths we quantified the deposition of Pseudomonas fluorescens Lp6a in columns containing glass collectors and on a quartz crystal microbalance. We found that the presence of DC reduced the efficiency of initial adhesion and bacterial surface coverage by >85%. A model is presented which quantitatively explains the reduction of bacterial adhesion based on the extended Derjaguin, Landau, Verwey, and Overbeek (XDLVO) theory of colloid stability and the EOF-induced shear forces acting on a bacterium. We propose that DC fields may be used to electrokinetically regulate the interaction of bacteria with surfaces in order to delay initial adhesion and biofilm formation in technical installations or to enhance bacterial transport in environmental matrices.

Osteomyelitis of the foot and ankle: diagnosis, epidemiology, and treatment

Osteomyelitis of the foot and ankle is a common, potentially devastating condition with diagnostic and treatment challenges. Understanding the epidemiology and pathogenesis of osteomyelitis can raise clinical suspicion and guide testing and treatments. History and physical examination, laboratory studies, vascular studies, histologic and microbiologic analyses, and various imaging modalities contribute to diagnosis and treatment. Treatment including empiric broad-spectrum antibiotics and surgery should take a multidisciplinary approach to optimize patient factors, ensure eradication of the infection, and restore function. Optimization of vascular status, soft tissues, limb biomechanics, and physiologic state of the patient must be considered to accelerate and ensure healing.

Effects of rotating magnetic field exposure on the functional parameters of different species of bacteria

The aim of the present study was to determine the effect of the rotating magnetic field (RMF) on the growth, cell metabolic activity and biofilm formation by S. aureus, E. coli, A. baumannii, P. aeruginosa, S. marcescens, S. mutans, C. sakazakii, K. oxytoca and S. xylosus. Bacteria were exposed to the RMF (RMF magnetic induction B = 25-34 mT, RMF frequency f = 5-50 Hz, time of exposure t = 60 min, temperature of incubation 37 °C). The persistence of the effect of exposure (B = 34 mT, f = 50 Hz, t = 60 min) on bacteria after further incubation (t = 300 min) was also studied. The work showed that exposure to RMF stimulated the investigated parameters of S. aureus, E. coli, S. marcescens, S. mutans, C. sakazakii, K. oxytoca and S. xylosus, however inhibited cell metabolic activity and biofilm formation by A. baumannii and P. aeruginosa. The results obtained in this study proved, that the RMF, depending on its magnetic induction and frequency can modulate functional parameters of different species of bacteria.

Aquatic biofouling prevention by electrically charged nanocomposite polymer thin film membranes

Electrically conductive polymer-nanocomposite (ECPNC) tight nanofiltration (NF) thin film membranes were demonstrated to have biofilm-preventing capabilities under extreme bacteria and organic material loadings. A simple route to the creation and application of these polyamide-carbon nanotube thin films is also reported. These thin films were characterized with SEM and TEM as well as FTIR to demonstrate that the carbon nanotubes are embedded within the polyamide and form ester bonds with trimesoyl chloride, one of the monomers of polyamide. These polymer nanocomposite thin film materials boast high electrical conductivity (∼400 S/m), good NaCl rejection (>95%), and high water permeability. To demonstrate these membranes' biofouling capabilities, we designed a cross-flow water filtration vessel with insulated electrical leads connecting the ECPNC membranes to an arbitrary waveform generator. In all experiments, conducted in highly bacterially contaminated LB media, flux tests were run until fluxes decreased by 45 ± 3% over initial flux. Biofilm-induced, nonreversible flux decline was observed in all control experiments and a cross-flow rinse with the feed solution failed to induce flux recovery. In contrast, flux decrease for the ECPNC membranes with an electric potential applied to their surface was only caused by deposition of bacteria rather than bacterial attachment, and flux was fully recoverable following a short rinse with the feed solution and no added cleaning agents. The prevention of biofilm formation on the ECPNC membranes was a long-term effect, did not decrease with use, and was highly reproducible.

The effect of vibration frequency and amplitude on biofouling deterrence

The use of vibration is proposed as a means of controlling the settlement of marine fouling organisms. In this study, panels with embedded lead zirconate titanate, known as PZT, were placed in the field over 3 months. The panels were vibrated at different velocity levels at frequencies between 70 and 445 Hz. It was found that barnacles (Amphibalanus variegatus Darwin and Elminius sp.) were the only fouling organisms affected by the applied vibration, and these organisms settled in significantly lower numbers when the plates were excited at specific frequencies and amplitudes. Panels vibrating at relatively higher frequencies, greater than 260 Hz, exhibited reduced barnacle settlement, whilst lower frequencies in the 70-100 Hz range had little or no effect. The settlement of other fouling organisms such as tubeworms, bryozoans, ascidians and algae did not appear to be affected by the applied excitation. The experimental results showed that increasing the velocity amplitude of vibration was a contributing factor in inhibiting barnacle settlement.

Prevention of Pseudomonas aeruginosa adhesion by electric currents

The process of controlling bacterial adhesion using an electric current deserves attention because of its ease of automation and environmentally friendly nature. This study investigated the role of electric currents (negative, positive, alternating) for preventing adhesion of Pseudomonas aeruginosa and achieving bacterial inactivation. Indium tin oxide (ITO) film was used as a working electrode to observe adhesion and inactivation under electric polarization. Electric current types were classified into negative, positive, and alternating current. The working electrode acted as a cathode or anode by applying a negative or positive current, and an alternating current indicates that the negative current was combined sequentially with the positive current. The numbers of adhered cells were compared under a flow condition, and the in situ behavior of the bacterial cells and the extent of their inactivation were also investigated using time-lapse recording and live/dead staining, respectively. The application of a negative current prevented bacterial adhesion significantly (∼81% at 15.0 μA cm(-2)). The positive current did not significantly inhibit adhesion (<20% at 15.0 μA cm(-2)), compared to the nonpolarized case. The alternating current had a similar effect as the negative current on preventing bacterial adhesion, but it also exhibited bactericidal effects, making it the most suitable method for bacterial adhesion control.

Involvement of reactive oxygen species in the electrochemical inhibition of barnacle (Amphibalanus amphitrite) settlement

The role of reactive oxygen species (ROS) in electrochemical biofouling inhibition was investigated using a series of abiotic tests and settlement experiments with larvae of the barnacle Amphibalanus amphitrite, a cosmopolitan fouler. Larval settlement, a measure of biofouling potential, was reduced from 43% +/- 14% to 5% +/- 6% upon the application of pulsed electric signals. The application of ROS scavengers such as glutathione and catalase counteracted the inhibitory effects of the electric signals, allowing settlement, and thus indicating that ROS are antifouling agents. Based on the experimental evidence, the proposed mechanism for ROS-based fouling prevention with interdigitated electrodes involved the electrochemical generation of hydrogen peroxide by oxygen reduction, and its likely reduction to hydroxyl radicals. Either hydroxyl radicals or products of hydroxyl radical reactions appeared to be the main deterrents of larval settlement.

Microbial biofilm voltammetry: direct electrochemical characterization of catalytic electrode-attached biofilms

While electrochemical characterization of enzymes immobilized on electrodes has become common, there is still a need for reliable quantitative methods for study of electron transfer between living cells and conductive surfaces. This work describes growth of thin (<20 microm) Geobacter sulfurreducens biofilms on polished glassy carbon electrodes, using stirred three-electrode anaerobic bioreactors controlled by potentiostats and nondestructive voltammetry techniques for characterization of viable biofilms. Routine in vivo analysis of electron transfer between bacterial cells and electrodes was performed, providing insight into the main redox-active species participating in electron transfer to electrodes. At low scan rates, cyclic voltammetry revealed catalytic electron transfer between cells and the electrode, similar to what has been observed for pure enzymes attached to electrodes under continuous turnover conditions. Differential pulse voltammetry and electrochemical impedance spectroscopy also revealed features that were consistent with electron transfer being mediated by an adsorbed catalyst. Multiple redox-active species were detected, revealing complexity at the outer surfaces of this bacterium. These techniques provide the basis for cataloging quantifiable, defined electron transfer phenotypes as a function of potential, electrode material, growth phase, and culture conditions and provide a framework for comparisons with other species or communities.

Sodium dodecyl sulfate allows the persistence and recovery of biofilms of Pseudomonas fluorescens formed under different hydrodynamic conditions

The effect of the anionic surfactant sodium dodecyl sulfate (SDS) on Pseudomonas fluorescens biofilms was investigated using flow cell reactors with stainless steel substrata, under turbulent (Re = 5200) and laminar (Re = 2000) flow. Steady-state biofilms were exposed to SDS in single doses (0.5, 1, 3 and 7 mM) and biofilm respiratory activity and mass measured at 0, 3, 7 and 12 h after the SDS application. The effect of SDS on biofilm mechanical stability was assessed using a rotating bioreactor. Whilst high concentrations (7 mM) of SDS promoted significant biofilm inactivation, it did not significantly reduce biofouling. Turbulent and laminar flow-generated biofilms had comparable susceptibility to SDS application. Following SDS exposure, biofilms rapidly recovered over the following 12 h, achieving higher respiratory activity values than before treatment. This phenomenon of post-treatment recovery was more pronounced for turbulent flow-generated biofilms, with an increase in SDS concentration. The mechanical stability of the biofilms increased with surfactant application, except for SDS concentrations near the critical micellar concentration, as measured by biofilm removal due to an increase in external shear stress forces. The data suggest that although SDS exerts antimicrobial action against P. fluorescens biofilms, even if only partial and reversible, it had only limited antifouling efficacy, increasing biofilm mechanical stability at low concentrations and allowing significant and rapid recovery of turbulent flow-generated biofilms.

Inhibition of barnacle (Amphibalanus amphitrite) cyprid settlement by means of localized, pulsed electric fields

The increasing needs for environmental friendly antifouling coatings have led to investigation of new alternatives for replacing copper and TBT-based paints. In this study, results are presented from larval settlement assays of the barnacle Amphibalanus (= Balanus) amphitrite on planar, interdigitated electrodes (IDE), having 8 or 25 mum of inter-electrode spacing, upon the application of pulsed electric fields (PEF). Using pulses of 100 ms in duration, 200 Hz in frequency and 10 V in pulse amplitude, barnacle settlement below 5% was observed, while similar IDE surfaces without pulse application had an average of 40% settlement. The spacing between the electrodes did not affect cyprid settlement. Assays with lower PEF amplitudes did not show significant settlement inhibition. On the basis of the settlement assays, the calculated minimum energy requirement to inhibit barnacle settlement is 2.8 W h m(-2).