The role of erosion in tooth wear: aetiology, prevention and management

The effect of location/site on polished human enamel after mechanical and chemical wear

OBJECTIVE

To compare profilometry and microhardness of polished occlusal and buccal human enamel following a mechanical and chemical wear regime.

METHODS

Enamel from polished human molars were sectioned into buccal and occlusal surfaces and randomly allocated into two groups (n = 10) and then exposed to 0.3 % citric acid at pH 2.7 for 10, 20, 40 and 60 mins each followed by abrasion with non-fluoridated toothpaste for 240 strokes in a reciprocating brushing machine. A white light profilometer with a spot size of 12 um measured mean step-height following each cycle. Microhardness indentations were conducted following the final cycled 60 mins erosion/abrasion using 0.01, 0.02, 0.1, 0.5 and 2.5 kgf indentation load. Statistical disparity were evaluated using a two-way ANOVA and post-hoc Sidak's multiple comparisons tests at α = 0.05.

RESULTS

After erosion/abrasion, the mean (SD) step-heights on occlusal and buccal surfaces were not significantly different until 60 mins, when occlusal surfaces exhibited greater step-heights, 32.9 µm (2.8) and 31.1 µm (1.8) and p = 0.02, respectively. Buccal and occlusal microhardness was statistically lower following erosion/abrasion at loads of 0.01 kgf (p = 0.0005) and 0.02 kgf (p = 0.0006) but no significant differences were observed in the microhardness between the surfaces at any loads.

CONCLUSION

The occlusal and buccal surfaces were not statistically different for microhardness or step height suggesting the susceptibility to wear is not related to the anatomy and structure of the tooth and is more likely related to other factors such as the environment.

CLINICAL SIGNIFICANCE

The study emphasizes that a notable difference in wear between occlusal and buccal enamel surfaces emerges only after prolonged exposure to simultaneous chemical and mechanical stress. This finding necessitates a preventive dental approach that accounts for both the duration of exposure and environmental factors.

CAD/CAM leucite-reinforced glass-ceramic for simulation of attrition in human enamel in vitro

OBJECTIVE

Investigate attrition simulation using CAD/CAM leucite-reinforced glass-ceramic antagonists on occlusal vs. buccal enamel.

METHODS

Three dental materials with known wear rates (resin-modified glass-ionomer, micro-filled, and fine particle composites) validated the wear simulator (CAD/CAM glass-ceramic antagonists, 200 cycles, 80 N load, deionised water irrigation, 0.7 mm sliding movement). Following this, human molars were sectioned into paired occlusal and buccal polished samples (n = 8/gp). Exposed 1.5 mm Ø enamel areas were subjected to attritional wear with and without pre-immersion in citric acid (5 min, 0.3%, pH 3.8). Profilometry measured step-height enamel wear and surface microhardness at different depths was calculated using Vickers indentation at 0.1 N and 0.5 N loads.

RESULTS

Dental material wear using the CAD/CAM antagonists showed consistency with previous data: mean (SD) resin-modified glass ionomer material loss of 177.77 (16.89) µm vs. 22.15 (1.30) µm fine particle hybrid composite resin wear vs. 13.63 (1.02) µm micro filled composite resin wear (P < 0.001). The coefficient of variation was less than 10%. Following validation, enamel sample wear was significantly increased when attrition was introduced (P < 0.001) independent of buccal vs. occlusal sample location (P < 0.05). Attrition resulted in occlusal wear of 26.1 ± 4.5 µm vs. buccal 26.3 ± 1.2 µm and attrition/erosion resulted in occlusal wear of 26.05 ± 4.46 µm vs. buccal 25.27 ± 1.16 µm. Whereas erosion-alone resulted in occlusal wear of 1.65 ± 0.13 µm and buccal 1.75 ± 0.03 µm. Microhardness testing at different loads revealed significantly greater hardness reductions in occlusal enamel vs. buccal enamel for 0.1 KgF indentations (P < 0.001) whereas in contrast 0.5 KgF indentations showed no differences.

SIGNIFICANCE

Wear simulation with CAD/CAM glass ceramic antagonists produced consistent wear in dental materials and human enamel, regardless of enamel surface origin. Lighter (0.1 KgF) hardness testing of occlusal vs. buccal origin revealed damage to the mechanical integrity of the superficial worn enamel.

Association between salivary characteristics and tooth wear: A systematic review and meta-analysis

OBJECTIVE

Literature was systematically reviewed to identify salivary characteristics and their association with tooth wear.

DATA

A protocol was developed a priori (PROSPERO CRD42022338590). Established systematic review methods were used for screening, data extraction, and synthesis. Risk of bias and the certainty of evidence were assessed using the JBI tools and GRADE, respectively. Direct and indirect association between tooth wear and salivary components and characteristics were assessed.

SOURCES

MEDLINE, Embase, SCOPUS, Web of Science, CINAHL, and additional sources were searched.

STUDY SELECTION

Studies reporting salivary characteristics in patients with tooth wear or models thereof were included. Animal and in-vitro studies and case reports were excluded.

RESULTS

One-hundred eleven studies were included. Qualitative analyses showed a negative association between tooth wear and salivary pH and flow rate in many studies. The higher the study size the higher the chances that an association with pH and flow rate was found. Xerostomia, buffer capacity and salivary consistency/viscosity had also some degree of association with tooth wear in fewer studies. Associations with the 39 salivary components were scarcer. Random effects meta-analyses (7 studies) showed that pH levels in stimulated whole saliva were lower in patient with tooth wear compared to controls (-0.07 [-0.10 to -0.04]). However, there was not enough evidence to establish a quantitative association with flow rate. The general risk of bias was unclear and the certainty of evidence was low or very low. A large diversity of methodologies limited the inclusion of all studies in quantitative synthesis.

CONCLUSION

From all potential risk factors, stimulated whole saliva pH showed a negative association, both quantitatively and qualitatively with tooth wear, indicating potential usefulness of pH monitoring in these patients. Moreover, associations between flow rate and tooth wear were observed qualitatively. However, in both cases the risk of bias was mostly unclear, and the certainty of evidence was low. No causal associations could be observed.

CLINICAL SIGNIFICANCE

Tooth wear is a prevalent condition that may lead to functional or esthetic impairments and pain. Knowing the potential risk factors like salivary pH or flow rate and their dynamics could be relevant during tooth wear monitoring and to intervene accordingly, especially in conditions like gastroesophageal reflux disease.

Different vehicles containing CaneCPI-5 reduce erosive dentin wear in situ

OBJECTIVE

This study evaluated the protective capacity of a sugarcane-derived cystatin (CaneCPI-5) in different vehicles (1-solution and 2-chitosan gel) against erosive dentin wear in situ.

METHODS

In part-1, 15 volunteers participated in a crossover protocol (solutions): Water; Elmex™ and CaneCPI-5. The volunteers wore an appliance with 4 dentin samples for 5 days. These samples were treated with a drop of the solutions for 1 min (4X/d), then the acquired pellicle (AP) was formed and the samples were subjected to erosive challenges (EROSION: citric acid, for 90 s, 4X/day). 2X/day, half of the samples were also abraded for 15 s (ABRASION). In part-2, 16 volunteers participated in a crossover protocol (gel): No gel, Chitosan gel, Chitosan gel + NaF and Chitosan gel + CaneCPI-5. The volunteers also wore an appliance. The samples were treated once/day with the gel or not for 4 min, then the AP was formed and the samples were subjected to erosive and abrasive challenges, as reported in part-1. Dentin wear was measured by profilometry. Data were analyzed by two-way RM-ANOVA and Sidak's tests (p < 0.05).

RESULTS

Part-1: Elmex™ and CaneCPI-5 significantly reduced dentin loss in comparison with Water for the EROSION/ABRASION conditions (p < 0.05). Part-2, all the treated groups significantly reduced the dentin loss in comparison to the No gel. The greatest reduction was found for the gel + CaneCPI-5 group for the EROSION/ABRASION (p < 0.05).

CONCLUSION

The solution and chitosan gel containing CaneCPI-5 protected against erosive dentin wear in situ.

CLINICAL RELEVANCE

These different vehicles are probably sufficient for protecting people with high risk of developing erosive dentin wear.

Effect of air-abrasion pretreatment with three bioactive materials on enamel susceptibility to erosion by artificial gastric juice

OBJECTIVE

The purpose of the study was to investigate the protective effect of three in-office preventive treatments with bioactive materials against enamel erosion induced by artificial gastric juice similar to that found in gastroesophageal reflux disease (GERD) patients. The treatments included air-abrasion of enamel with a fluoride-containing bioactive glass (BioMinF®), Bioglass 45S5 (ProSylc) and nano-hydroxyapatite (MI Pearls) to test enamel susceptibility following an erosive challenge.

METHODS

Enamel surface loss was evaluated using confocal microscopy, while changes in enamel surface roughness and morphology were also investigated after the treatments. SEM and EDS were used to observe formation of apatite crystals on enamel and to detect alterations in mineral composition. In Group 1 (negative control) the specimens did not receive any treatment; Group 2 specimens (positive control) treated with 0.4 % SnF₂, while in Groups 3-5 enamel was air-abraded with BioMinF®, ProSylc and MI Pearls, respectively.

RESULTS

All the experimental groups reduced significantly enamel surface loss compared to the negative control group (p < 0.05), except for the MI Pearls treatment (p > 0.05). The most protective behavior against erosion presented the treatment with SnF₂. BioMinF induced the larger amount of apatite crystals on the enamel surface, followed by ProSylc.

SIGNIFICANCE

BioMinF and ProSylc treatments may be beneficial against dental erosion induced by gastric juice in GERD patients, while MI Pearls treatment may not suitable for this indication. Both materials promote formation of apatite crystals on enamel in acidic conditions protecting the surface from the erosion. The tested treatments may be useful in GERD patients who cannot comply with at-home therapies with SnF₂.

Dental Erosion in Obese Patients before and after Bariatric Surgery: A Cross-Sectional Study

Obese patients are at risk of dental erosion due to micronutrient deficiency, consumption of soft drinks, gastric reflux disease and vomiting. The present study evaluates the presence of dental erosion in obese patients before and after bariatric surgery using the BEWE (basic erosive wear examination) scoring system. A total of 62 patients with severe obesity were included in the analysis, 31 in the control group (without bariatric surgery) and 31 in the surgery group (after bariatric surgery). BEWE scores did not vary between groups. Vitamin D deficiency was detected in 19 patients in the control group and three in the surgery group (p < 0.001). The serum calcium and vitamin D values were significantly higher in the surgery group (p = 0.003, p < 0.001 consecutively). All patients after bariatric surgery showed compliance with supplements, including vitamin D and calcium daily. Patients after bariatric surgery were less likely to drink soft drinks regularly (p = 0.026). Obese patients, before or after bariatric surgery, are at risk for erosive dental wear. However, with sufficient education prior to surgery and consistent intake of vitamin and mineral supplements, significant erosive dental wear after bariatric surgery could be avoided. Regular dental examination should be included in the check-up and follow-up program.

Diagnosis of Occlusal Tooth Wear Using 3D Imaging of Optical Coherence Tomography Ex Vivo

The aim of this study was to assess the utility of 3D imaging of optical coherence tomography (OCT) for the diagnosis of occlusal tooth wear ex vivo. Sixty-three extracted human molars with or without visible tooth wear were collected to take digital intraoral radiography and 3D OCT images. The degree of tooth wear was evaluated by 12 examiners and scored using 4-rank scale: 1-slight enamel wear; 2-distinct enamel wear; 3-tooth wear with slight dentin exposure; 4-tooth wear with distinct involvement of dentin. The degree of tooth wear was validated by the histological view of confocal laser scanning microscopy (CLSM). The sensitivity, specificity, and area under the curve (AUC) of receiver operating characteristic analysis were calculated. Diagnostic accuracy was compared with the agreement with CLSM observation using weighted kappa. The results were statistically analyzed at a significance level of α = 0.05. Three-dimensional OCT showed significantly higher sensitivity (p < 0.05) for all the diagnostic thresholds of enamel wear and dentin exposure than digital radiography (0.82, 0.85, and 0.79 vs. 0.56, 0.52, and 0.57, respectively). Three-dimensional OCT showed higher AUC and kappa coefficients than digital radiography (p < 0.05), where mean AUC and Kappa values were 0.95 and 0.76 for OCT and 0.92 and 0.47 for radiography, respectively. No significant difference of specificity was observed (p > 0.05). Three-dimensional OCT could visualize and estimate the degree of tooth wear and detect the dentin exposure at the tooth wear surface accurately and reproducibly. Consequently, a new guideline for tooth wear assessment can be proposed using OCT.

Evaluation of dental caries, tooth crack, and age-related changes in tooth structure using optical coherence tomography

Optical coherence tomography (OCT) is an imaging technique that can visualize the internal biological structure without X-ray exposure. Swept-source OCT (SS-OCT) is one of the latest version of OCT, wherein the light source is a tunable laser that sweeps near-infrared wavelength light to achieve real-time imaging. The imaging depth of OCT is highly influenced by the translucency of the medium. The medium that does not transmit light and the deeper structure beyond the range of light penetration depth are not relevant for OCT imaging. In OCT, sound enamel is almost transparent at the OCT wavelength range, and enamel and dentin can be distinguished from each other as the dentin-enamel junction (DEJ) appears as a dark border. Demineralized enamel and dentin are imaged as bright zones because of the formation of numerous micro-porosities where the backscatter of OCT signal is increased. In cavitated caries at interproximal or occlusal hidden zone, the upper margin of the cavity reflects the signal showing a distinct bright border in the SS-OCT image. SS-OCT is capable of determining crack penetration depth even when the cracks extended beyond the DEJ. SS-OCT has a high degree of sensitivity and specificity for the detection of dental caries and tooth cracks. SS-OCT is also capable of detecting non-carious cervical lesions and occlusal tooth wear in cross-sectional views to estimate the amount of tooth structure loss.

Erosive Tooth Wear and Erosive Esophagitis in Children: An Observational Study in Porto Alegre, Brazil

The aim of this study was to establish and compare the prevalence and severity of erosive tooth wear (ETW) in children with and without erosive esophagitis. Children aged 5-12 years, scheduled for upper digestive endoscopy at the Pediatric Gastroenterology Service of the Children's Hospital Santo Antonio, Porto Alegre, Brazil, were eligible to participate in this study. Patients who presented erosive esophagitis at endoscopy were defined as gastroesophageal reflux disease (GERD) carriers, and the severity was described according to the Los Angeles classification. The oral cavity examination was performed by a trained and calibrated dentist and ETW was classified using the Basic Erosive Wear Examination (BEWE) index. Parents/guardians answered a questionnaire about the patients' diets and frequency of consumption of acidic foods and beverages. A total of 110 children were included in the study. Erosive esophagitis was observed in 24 patients (21.8%) and all of them (100%) presented ETW, showing a statistically significant association between these 2 conditions (p < 0.05). Among children who did not present with erosive esophagitis (n = 86), 54 (64.3%) had an ETW risk level of none according to their BEWE scores (0-2). The results of this study showed a statistically significant association between erosive esophagitis and ETW, thus it can be concluded that it is important to recognize groups at risk of ETW and act together with medical professionals to ensure adequate oral health for these patients.

Predictors of dental erosions in patients evaluated with upper digestive endoscopy: a cross-sectional study

The most studied medical condition related with dental erosions is gastroesophageal reflux disease (GERD). The aim of this study was to assess other predictors of dental erosions besides GERD in outpatients referred for upper digestive endoscopy. In a cross-sectional study, we prospectively evaluated 235 patients who underwent upper digestive endoscopy. Patients were interviewed and examined by a trained dentist before the endoscopies, addressing dental health as well as clinical information and food intake. Dental erosion was classified using Basic Erosive Wear Examination score. Potential predictors for dental erosions were: gender, age, chronic use of antidepressants and proton pump inhibitors (PPI), diabetes mellitus, body mass index, heartburn and acid regurgitation scores, chocolate intake, reflux esophagitis and hiatal hernia. Overall prevalence of dental erosions was 23.4%. The most parsimonious Poisson regression model for dental erosions considered age, chocolate intake and acid regurgitation as predictors. Dental erosions were associated with acid regurgitation in patients younger than 50 years [adjusted prevalence ratio (PR) = 1.8 (95% CI 1.1-2.9)] and with chocolate intake in patients older than 50 years [PR = 2.1 (95% CI 1.2-3.9]. The surfaces most eroded were palatine/lingual (n = 25) and occlusal (n = 25), followed by vestibular (n = 5). In outpatients evaluated with upper digestive endoscopy, the variables associated with dental erosions were age younger than 50 years, acid regurgitation and chocolate intake. Referral for dental evaluation should be considered for young patients with GERD and frequent acid regurgitation.

The impact of etching time and material on bond strength of self-adhesive resin cement to eroded enamel

The purpose of this study was to assess the effect of pre-etching time and material on shear bond strength (SBS) of self-adhesive resin cements to eroded and sound enamel. Eroded enamel specimens were assigned into 5 groups (n=20 each) based on enamel surface treatment as follow: Group N, eroded enamel (without surface pre-treatment); Group PH15, 35% H₃PO₄ etching for 15 s; Group PH30, 35% H₃PO₄ etching for 30 s; Group L30, 20% lactic acid etching for 30 s and Group L60, 20% lactic acid etching for 60 s.Composite blocks were fabricated and cemented to enamel surfaces with one of two self-adhesive cements. Notched-edge SBS was assessed. Bond strength of self-adhesive cement to eroded enamel surface significantly enhanced following application of 20% lactic acid for 30 s.

Tooth wear in Swedish adults-A cross-sectional study

BACKGROUND

Tooth wear has been recognised as a growing oral health problem in children and adolescents, with erosion often cited as the main cause of the tooth wear. Most studies on tooth wear have been conducted on children and adolescents, and only few studies focus on adults. Our aim was to study the prevalence of different types of tooth wear in an adult population and investigate related factors to tooth wear.

METHODS

A total of 831 adults in Sweden participated in the study by completing a questionnaire about oral health, a clinical examination, saliva sample and intraoral photographs. Tooth wear was estimated according to the Basic Erosive Wear Examination index, and the aetiology was determined based on the clinical appearance.

RESULTS

Almost 80% of the individuals had signs of erosion, and over 90% had signs of attrition. A high level of tooth wear was found in 4.6% of the individuals, few of who reported having received information about both attrition and erosion. Significantly, more men had tooth wear. Daily consumption of fruit had a stronger correlation to tooth wear than acidic drinks.

DISCUSSION & CONCLUSION

A high level of tooth wear was found in 4.6% of the individuals, and it was more common in men than women. Aside from attrition, tooth wear due to erosion was a frequent finding in adults. Only a few of the individuals with a high level of tooth wear reported to have received information about tooth wear from their dentist or dental hygienist.

Aesthetic Rehabilitation of a Patient with Bruxism Using Ceramic Veneers and Overlays Combined with Four-Point Monolithic Zirconia Crowns for Occlusal Stabilization: A 4-Year Follow-Up

Management of severe worn dentition in patients with bruxism is challenging as a result of the loss of tooth structure and occlusal vertical dimension, temporomandibular implications, tooth hypersensitivity, and masticatory or aesthetic impairment. This case describes the 4-year follow-up clinical evaluation of a full mouth tooth-supported rehabilitation made on a 66-year-old man with bruxism and tooth wear, with aesthetic complaints and compromised masticatory function. The prosthetic treatment was planned with a digital smile design and a mock-up technique for an aesthetic and minimally invasive approach using lithium disilicate pressed and layered veneers on anterior teeth, posterior CAD/CAM lithium disilicate overlays with facial coverage, and CAD/CAM monolithic zirconia crowns with facial feldspathic ceramic on maxillary and mandibular canines and first molars in order to ensure the occlusal stability at the increased occlusal vertical dimension. After 4 years of function, no complications were registered. The choice of an appropriate material for the rehabilitation of these patients is essential to improve treatment prognosis and should be guided by mechanical and aesthetical properties. The use of four-point occlusal stabilization with CAD/CAM high strength monolithic zirconia crowns combined with ceramic veneers and overlays appears to be a reliable treatment option that enhances aesthetics and minimizes the occurrence of ceramic fractures, ensuring the treatment prognosis and predictability.

A survey on the prevalence and risk indicators of erosive tooth wear among adolescents in Guangzhou, South China

BACKGROUND

Erosive tooth wear (ETW) has become a crucial oral health problem over the decades in China.

OBJECTIVES

To explore the prevalence and risk indicators of ETW among adolescents in Guangzhou, south China.

METHODS

A cross-sectional survey of 720 participants was conducted in Guangzhou, using an equal-sized, stratified, multistage random sampling approach. The participants were from two different age groups (12- and 15-year-olds), 360 per group. The ratio of males to females was 1:1 in each group. ETW was recorded utilising the basic erosive wear examination (BEWE) index as the dependent variable. Independent variables included age, gender, region, socioeconomic status, dietary factors, oral health measures and others.

RESULTS

The prevalence rates (weighted) of ETW and dentin exposure (DE) were 56.1% and 26.2% among adolescents in Guangzhou, with mean teeth (weighted) of 1.8 ± 2.5 and 0.6 ± 1.5, respectively. No matter the prevalence or the mean teeth, the 15-year-olds were higher than the 12-year-olds; the mean teeth of ETW of males was higher than that of females; the mean teeth of ETW and DE of the adolescents of low socioeconomic status were higher than those of high socioeconomic status. Medium to high risk levels were found for 10.1%. In the multiple regression model, age, gender and taking acidic foods/drinks before sleep were associated with ETW.

CONCLUSIONS

Moderate ETW in the permanent dentition was common among adolescents in Guangzhou. However, the teeth involved were low. Dietary factors and demographics were the main risk indicators.

[Tooth Erosions Associated with Gastroesophageal Reflux: Cause, Prevention and Restorative Therapy]

Tooth Erosions Associated with Gastroesophageal Reflux: Cause, Prevention and Restorative Therapy Abstract. Dental erosions are caused by the recurring contact of solutions which are unsaturated in tooth minerals,ith hard tooth substances. This initially leads to softening and later to an irreversible loss of hard tooth substance. Erosion is observed particularly with excessive consumption of acidic foods (e.g. soft drinks or citrus fruits) but also in connection with gastrointestinal (gastroesophageal reflux disease) or psychosomatic diseases (anorexia nervosa or bulimia nervosa). The aim of this article is to define dental erosions, their causes, prevalence and consequences as well as possible preventive measures. Based on a clinical example of a patient with reflux-related erosions, a therapy option with direct composite tooth build-up is presented.

Ultrasonographic evaluation of jaw elevator muscles in young adults with bruxism and with and without attrition-type tooth wear: A pilot study

OBJECTIVE

This pilot study was planned to analyze masticatory activation in bruxism patients with and without attrition by ultrasonographic evaluation of mandibular adductor muscles.

METHODS

Sixty bruxism patients (group 1: 30 without attrition, group 2: 30 with attrition) and an age-sex matched control of 30 (group 3) were clinically examined. The thickness of bilateral temporalis and masseter muscles during clench and rest was measured by ultrasonography.

RESULTS

The mean muscle thicknesses were higher in bruxing patients than in controls. In group 2, the clench/rest ratio (C/R) of the right and left masseter and temporal muscles were higher than the control group (p = 0.03, p = 0.01, p = 0.04, p = 0.03, respectively).

CONCLUSION

The thickness of chewing muscles increases with bruxism. The occlusal forces in the teeth increase, and therefore, the tooth wear increases. Ultrasonographic muscle thickness can be used to determine muscle activity in bruxism patients.

Effect of Different Computer-aided Design/Computer-aided Manufacturing (CAD/CAM) Materials and Thicknesses on the Fracture Resistance of Occlusal Veneers

The aim was to evaluate, in vitro, the influence of different computer-aided design/computer-aided manufacturing (CAD/CAM) materials (IPS e.max CAD, Vita Enamic, and Lava Ultimate) and thicknesses (0.6 mm and 1.5 mm) on the fracture resistance of occlusal veneers. Sixty human third molars were prepared to simulate advanced erosion of the occlusal surface, and the teeth were randomly divided into six experimental groups (n=10) according to the material and thickness used to build the veneers. Ten sound teeth formed the control group. The veneers were adhesively luted and submitted to mechanical cyclic loading (1 million cycles at 200-N load). The fracture resistance test was performed in a universal testing machine. The failures were classified as "reparable" and "irreparable." According to two-way analysis of variance and the Tukey test, the interaction (material × thickness) was significant ( p=0.013). The highest fracture resistance was obtained for IPS e.max CAD at a 1.5-mm thickness (4995 N) and was significantly higher compared to the other experimental groups ( p<0.05). The lowest fracture resistance was obtained for Vita Enamic at 0.6 mm (2973 N), although this resistance was not significantly different from those for IPS e.max CAD at 0.6 mm (3067 N), Lava Ultimate at 0.6 mm (3384 N), Vita Enamic at 1.5 mm (3540 N), and Lava Ultimate at 1.5 mm (3584 N) ( p>0.05). The experimental groups did not differ significantly from the sound teeth (3991 N) ( p>0.05). The failures were predominantly repairable. The occlusal veneers of IPS e.max CAD, Vita Enamic, and Lava Ultimate, with thicknesses of 0.6 mm and 1.5 mm, obtained fracture resistances similar to those associated with sound teeth.

Reduced statherin in acquired enamel pellicle on eroded teeth compared to healthy teeth in the same subjects: An in-vivo study

The aim of this in-vivo study was to compare total protein and four key salivary proteins present in the acquired enamel pellicle (AEP) on eroded and non-eroded surfaces in participants with erosive tooth wear. Participants with erosive tooth wear of dietary non-intrinsic origin, present on the occlusal surfaces of the lower first molars and an unaffected posterior occlusal surface in the same quadrant were recruited from restorative dental clinics at King's College London Dental Institute (n = 29, REC ref 14/EM/1171). Following removal of the salivary film, AEP samples were collected from the eroded occlusal surfaces (EP, n = 29) and the non-eroded occlusal surfaces (NP, n = 29) using 0.5% sodium dodecyl sulfate (SDS) soaked filter papers. Total protein concentration was analysed using bicinchoninic acid assay (BCA). Protein fractions were separated using SDS-PAGE and immunoblotted against: mucin5b, albumin, carbonic anhydrase VI (CA VI) and statherin antibodies. Amounts were quantified using ImageLab software against purified protein standards of known concentration. ANOVA followed by paired t-test and Wilcoxon's matched-pair signed-rank test were used to test statistical significance. The difference was considered to be significant at a P value < 0.05. The total protein on eroded surfaces was significantly lower compared to the total protein on non-eroded surfaces [0.41mg/mL (0.04) and 0.61 mg/mL (0.11)] respectively (p< 0.05). The median (min, max) amount of statherin was also significantly lower on eroded occlusal surfaces [84.1 (20.0, 221.8) ng] compared to AEP from non-eroded teeth in the same subjects [97.1(30.0, 755.6) ng] (p = 0.002). No statistical differences were observed for mucin 5b, albumin or CA VI. The total protein and statherin in the in-vivo AEP were different between eroded and non-eroded tooth surfaces of the same patient.

Measurement of surface roughness changes of unpolished and polished enamel following erosion

Objectives

To determine if Sa roughness data from measuring one central location of unpolished and polished enamel were representative of the overall surfaces before and after erosion.

Methods

Twenty human enamel sections (4x4 mm) were embedded in bis-acryl composite and randomised to either a native or polishing enamel preparation protocol. Enamel samples were subjected to an acid challenge (15 minutes 100 mL orange juice, pH 3.2, titratable acidity 41.3mmol OH/L, 62.5 rpm agitation, repeated for three cycles). Median (IQR) surface roughness [Sa] was measured at baseline and after erosion from both a centralised cluster and four peripheral clusters. Within each cluster, five smaller areas (0.04 mm²) provided the Sa roughness data.

Results

For both unpolished and polished enamel samples there were no significant differences between measuring one central cluster or four peripheral clusters, before and after erosion. For unpolished enamel the single central cluster had a median (IQR) Sa roughness of 1.45 (2.58) μm and the four peripheral clusters had a median (IQR) of 1.32 (4.86) μm before erosion; after erosion there were statistically significant reductions to 0.38 (0.35) μm and 0.34 (0.49) μm respectively (p<0.0001). Polished enamel had a median (IQR) Sa roughness 0.04 (0.17) μm for the single central cluster and 0.05 (0.15) μm for the four peripheral clusters which statistically significantly increased after erosion to 0.27 (0.08) μm for both (p<0.0001).

Conclusion

Measuring one central cluster of unpolished and polished enamel was representative of the overall enamel surface roughness, before and after erosion.

Application of Diode Laser in the Treatment of Dentine Hypersensitivity

INTRODUCTION

Dentine hypersensitivity is characterized by acute, sharp pain arising from the exposed dentine, most commonly in response to thermal, tactile, or chemical stimuli, and which cannot be linked to any other pathological changes in the tooth or the environment. Therapy uses various impregnating agents in the form of solutions or gels and, in more recent times, laser.

AIM

The aim of this research was to examine the effects of treatment of hypersensitive dental cervix with diode laser.

MATERIALS AND METHODS

The study included 18 patients with 82 sensitive teeth. The degree of dentine hypersensitivity was evaluated by visual analogue scale (VAS), and the treatment was carried out by application of low-power diode laser over the span of three visits, which depended on the initial sensitivity.

RESULTS

There is a significant difference in VAS values measured at the onset of treatment (baseline) and immediately after the first laser treatment (t=9.275; p=0.000), after 7 days, after the second laser treatment (14 days) (t=7.085, p=0.000), as well as after 14 days and the third laser treatment (t=5.517, p=0.000), which confirms the effectiveness of this therapeutic procedure. The results showed a reduction of hypersensitivity in response to tactile stimulus with a probe after the third treatment, even with teeth whose value on the VAS was very high at the beginning of treatment (baseline).

CONCLUSION

Within the scope of the conducted study, laser therapy has provided extremely safe and effective results in the treatment of cervical dentine hypersensitivity.

Gastro-oesophageal reflux disease and dental erosions in adults: influence of acidified food intake and impact on quality of life

BACKGROUND AND AIM

Gastro-oesophageal reflux disease (GORD) and dental erosions (DE) have an established association. We assessed whether GORD is associated with DE controlling for acidified food intake and their relationships with quality of life (QOL).

METHODS

In this cross-sectional study, 419 adult patients who sought dentistry consultation were considered eligible. Patients responded to questionnaires for GORD symptoms, acidified food ingestion and World Health Organization quality of life (WHOQOL Bref), followed by an oral examination, in which DE were characterized according to the Smith & Knight criteria.

RESULTS

A total of 417 patients were included (43.8±13.7 years; 68.8% women). There were 143 patients with GORD (34.3%) and 274 controls without GORD. The prevalence of DE was higher in GORD patients compared with the controls (25.9 vs. 17.2%; P=0.041). GORD was associated with DE after adjusting for acidified food intake (P=0.035), with a prevalence ratio of 1.52 (0.95 confidence interval 1.03-2.22). The WHOQOL Bref score was significantly lower in the presence of GORD [median 17.2 (GORD-DE-) vs. 15.4 (GORD+DE+); P<0.01], irrespective of DE.

CONCLUSION

In adults examined in a referential dentistry centre in South America, DE were prevalent and significantly associated with GORD. This association was independent of the intake of acidified food in our study. Impairment in QOL was observed in GORD patients irrespective of the presence of DE.

Erosion and abrasion-inhibiting in situ effect of the Euclea natalensis plant of African regions

This study evaluated the effect of Euclea natalensis gel on the reduction of erosive wear with or without abrasion, in enamel and dentin. During two five-day experimental crossover phases, volunteers (n = 10) wore palatal devices containing human enamel and dentin blocks (E = 8 and D = 8). The gel was applied in a thin layer in the experimental group, and was not applied in the control group. In the intraoral phase, volunteers used the palatal appliance for 12 h before the gel treatment, and were instructed to start the erosive challenges 6 h after the gel application. Erosion was performed with Coca-Cola® (for 5 min) 4 times/day. The appliance was then put back into the mouth and was brushed after 30 minutes. After intraoral exposure, the appliances were removed and the specimens were analyzed using profilometry (mean ± SD, μm). The Euclea natalensis gel caused less wear in enamel in the experimental group (EROS = 12.86 ± 1.75 µm; EROS + ABRAS = 12.13 ± 2.12 µm) than in the control group (EROS = 14.12 ± 7.66 µm; EROS + ABRAS = 16.29 ± 10.72 µm); however, the groups did not differ from each other significantly. A statistically significant value was found for erosion and eros + abrasion in dentin (p = 0.001). Euclea natalensis may play a role in the prevention of dentin loss under mild erosive and abrasive conditions. A clinical trial is required to confirm these promising results in a clinical situation.

Effectiveness of resin-based materials against erosive and abrasive enamel wear

OBJECTIVE

The objective of this study was to test the effectiveness of resin-based materials against erosive enamel wear under erosive and abrasive challenges by orange juice and tooth brushing.

METHODS

Fifty enamel specimens from third molars were assigned to five groups: ICON resin infiltration with no etching (ICON-NE), ICON resin infiltration with 15 % HCl etching (ICON-AE), Seal & Protect sealant (S&P), Tetric EvoFlow (TEF), and control. Erosive lesions were first created on enamel, then treated with resin-based materials. Erosive and abrasive challenges by orange juice and tooth brushing were repeated after treatments. Erosive wear of the treated areas was measured with 3D scanning microscopy, and data were analyzed using ANOVA and paired t tests.

RESULTS

Treatments with ICON, S&P, and TEF created a protective material coating of 4.5 ± 1.9 μm, 44.3 ± 8.1 μm, and 84.6 ± 15.7 μm in thickness on the lesion surfaces, respectively. After 15 cycles of erosive and abrasive challenges, enamel or material losses were 21.9 ± 2.3 μm for control, 24.5 ± 4.0 μm for ICON-NE, 24.6 ± 7.4 μm for ICON-AE, 11.2 ± 4.1 μm for S&P, and 3.9 ± 1.9 μm for TEF, respectively. The protective coatings were completely lost in the ICON infiltration groups but remained intact in both the S&P and TEF groups after erosive and abrasive challenges.

CONCLUSION

In contrast to a resin sealant and a flowable composite, ICON infiltration resin was not effective in protecting enamel surfaces from erosive and abrasive wear.

CLINICAL RELEVANCE

Sealant and flowable composite resin may create protective coatings on eroded enamel surfaces and prevent further tissue loss.

Risk Assessment for Tooth Wear

Tooth wear has an increasing prevalence in the UK population. The aetiology is commonly multifactorial, and the aetiopathology is through a combination of erosion, attrition, abrasion and abfraction. Erosion is associated with intrinsic or extrinsic acids, and therefore subjects with reflux disease and eating disorders are at increased risk. Fruit juice, fruits and carbonated drink consumption, frequency of consumption and specific habits are also risk factors. Attrition is more prevalent in bruxists. Other habits need to be considered when defining the risk of tooth wear. Abrasion is usually associated with toothbrushing and toothpastes, especially in an already acidic environment. Patients with extensive lesions that affect dentin may be at higher risk, as well as those presenting with unstained lesions. Monitoring of the progress of tooth wear is recommended to identify those with active tooth wear. Indices for tooth wear are a helpful aid.

Assessment of oral hygiene habits, oral hygiene practices and tooth wear among fertilizer factory workers of Northern India: A Cross sectional study

BACKGROUND

The association between oral hygiene habits & practices and severity of tooth wear lesion varies from community to community and also from occupation to occupation. The present study was conducted with to assess oral hygiene habits & practices and tooth wear among fertilizer factory workers of Punjab, India.

MATERIAL AND METHODS

A descriptive cross sectional survey was conducted among 965 male workers who were aged between 19-58 years, who were the workers of fertilizers factory of Bathinda, India. An interview on the demographic profile, oral hygiene practices, and adverse habits followed a clinical examination for recording the Tooth Wear (Smith and Knight Index 1984) using Type III examination. The Chi-square test and a Stepwise multiple linear regression analysis were used for the statistical analysis. Confidence interval and p-value set at 95% and ≤ 0.05 respectively.

RESULTS

In the present study majority (47.2%) of the study population used chew sticks for cleaning their teeth. Overall prevalence of adverse habits was reported (92.4%). Study population showed higher prevalence of tooth wear (77.1%). Best predictors identified for Tooth Wear were oral hygiene practices, adverse habits, years of work experience and age respectively.

CONCLUSIONS

Considerable percentages of fertilizer factory workers have demonstrated a higher prevalence of tooth surface loss. This may be useful in designing the investigations that aim to further explore the causes for these findings and more importantly to plan oral health promotion program implementing both preventive and curative strategies.

KEY WORDS

Tooth wear, smith & knight index, fertilizer factory.

Amazonian delicacy tucupi is as erosive as a cola-based soft drink

OBJECTIVE

Acidic diets are advocated as main risk factor for tooth erosion, which could be prevented, or at least controlled, if patients were early advised. It is important to identify, hence, if possible dietary constituents regionally consumed on large scale, such as tucupi, a low-pH yellowish-green color and strong flavor delicacy made from the juice of a bitter cassava, may explain its occurrence in specific patient groups. This cross-over in situ/ex vivo study evaluated tucupi's ability to promote erosion of bovine enamel by assessing its percentage of surface microhardness change (%SMHC), taking a cola-based soft drink and human saliva as positive and negative controls.

DESIGN

For three 7-days spaced out legs of 7 days each, nine volunteers wore palatal devices with three bovine enamel blocks, which were challenged with one of the following solutions: TUC-tucupi (n=27); COL-cola-based soft drink (n=27); SAL-saliva (n=27). Erosive challenges were performed extra-orally (4×/day) by dropping TUC or COL at room temperature on specimens. After 5min, palatal devices were replaced into the mouth. SAL permanently acted as the negative control while volunteers solely wore the device. One-way ANOVA followed by Tukey's post-hoc tests (α=0.05) were applied.

RESULTS

TUC promoted an enamel %SMHC (-21.56±10.08(a)) similar than that promoted by COL (-18.19±12.99(a); p=0.275), which were both significantly higher than that promoted by SAL (-1.86±13.65(b); p<0.0001).

CONCLUSIONS

Besides the most worldwide appreciated cola-based soft drink, the greatly consumed Amazonian delicacy tucupi can be considered a potential risk factor for tooth erosion.

Prosthetic Rehabilitation of a Patient With Gastroesophageal Reflux Disease: Five-Year Follow-up

Tooth wear is a multifactorial process that is a growing concern in dentistry. This phenomenon can be caused by mechanical (attrition, abrasion, or abfraction) or chemical (erosion) processes. Etiologic factors in dental erosion can be due to changes in behavior, an unbalanced diet, or gastrointestinal disorders such as acid regurgitation, which may influence the salivary flow rate and buffering capacity of saliva. This case report describes an esthetic rehabilitation of a patient with gastroesophageal reflux and dental erosion, with a treatment rationale that includes the use of a diagnostic template and five-year follow-up. This technique, presented here in a clinical case with moderate enamel loss, integrates an additive wax-up and a direct intraoral bis-acryl resin mock-up. Lithium disilicate glass-ceramic (IPS e.max Press, Ivoclar Vivadent) laminate veneers were fabricated with the heatpress technique. They were veneered with a layering ceramic (IPS e.max Ceram, Ivoclar Vivadent) to improve the appearance of the incisal edge. The case demonstrated the success of veneers as an effective, conservative, and esthetic treatment for patients with this pathology.

Interaction of Polyelectrolytes with Salivary Pellicles on Hydroxyapatite Surfaces under Erosive Acidic Conditions

The modification of acidic beverage formulations with food-approved, nonhazardous substances with antierosive properties has been identified as a key strategy for counteracting the prevalence of dental erosion, i.e., the acid-induced dissolution of hydroxyapatite (HA, the main mineral component of tooth surfaces). While many of such substances have been reported, very little is known on how they interact with teeth and inhibit their acid-induced dissolution. With the aim of filling this gap in knowledge, we have studied under acidic conditions the interaction between two polyelectrolytes of differing ionic character, carboxymethyl cellulose (CMC) and chitosan, and saliva-coated hydroxyapatite, i.e., a model for the outer surface of teeth. These studies were performed by means of ellipsometry, quartz crystal microbalance with dissipation monitoring, and atomic force microscopy. We also studied, by means of pH variations, how dissolution of saliva-coated HA is affected by including these polyelectrolytes in the erosive solutions. Our results confirm that salivary films protect HA from acid-induced dissolution, but only for a limited time. If the acid is modified with CMC, this polyelectrolyte incorporates into the salivary films prolonging in time their protective function. Eventually, the CMC-modified salivary films are removed from the HA surfaces. From this moment, HA is continuously coated with CMC, but this offers only a weak protection against erosion. When the acid is modified with the cationic chitosan, the polyelectrolyte adsorbs on top of the salivary films. Chitosan-modified salivary films are also eventually replaced by bare chitosan films. In this case both coatings offer a similar protection against HA dissolution, which is nevertheless notably higher than that offered by CMC.

Assessment of masticatory muscle activity and occlusion time in patients with advanced tooth wear

OBJECTIVE

Tooth wear is a basic physiological adjustment mechanism in the masticatory system. Unfortunately, it is not clear what the relationship is between the activity of the masticatory muscles and the tooth hard tissue loss (mainly enamel) in patients with advanced tooth wear. The aims of this study were (1) to compare the occlusion times and (2) to compare the EMG activity in maximal voluntary clench of the masseter and anterior temporalis muscles of patients with advanced tooth wear to the same activity of healthy volunteers.

DESIGN

50 (16F, 34M) patients and 30 (12F, 18M) age matched controls were clinically examined to assess the degree of wear (TWI). Each subject underwent electromyographic analysis (bilateral anterior temporalis, superficial masseter, anterior digastric and sternocleidomastoid muscles) and digital occlusal analysis.

RESULTS

Mean values of the electrical potentials of the mandible elevating muscles during clench were higher in the study group compared to the controls. A negative correlation was found between the temporalis and masseter muscle activities during clench and the mean value of TWI (r=-0.383, p=0.009; r=-0.447, p=0.002). Occlusion time was longer in the study group compared to controls (p<0.05).

CONCLUSIONS

Mandibular adductors demonstrated lower muscular activities during clenching in the tooth wear patients; however, the cause of this finding is not certain. Prolongation of occlusion time may exacerbate occlusal surfaces wear or excessive wear may prolong occlusion time.

Biofilm and Dental Biomaterials

All treatment involving the use of biomaterials in the body can affect the host in positive or negative ways. The microbiological environment in the oral cavity is affected by the composition and shape of the biomaterials used for oral restorations. This may impair the patients’ oral health and sometimes their general health as well. Many factors determine the composition of the microbiota and the formation of biofilm in relation to biomaterials such as, surface roughness, surface energy and chemical composition, This paper aims to give an overview of the scientific literature regarding the association between the chemical, mechanical and physical properties of dental biomaterials and oral biofilm formation, with emphasis on current research and future perspectives.

Exploring some aspects associated with dentine hypersensitivity in children

BACKGROUND

The etiology of dentine hypersensitivity (DH) is still inconclusive and there are few studies concerning it in children.

AIM

To evaluate clinical, dietary, and salivary variables in children with DH complaints.

DESIGN

Forty-eight children were asked about DH. Data regarding dietary habits were collected from the children's parents and an examination was performed to determine dental erosion. Dental biofilm was estimated by oral hygiene status, according to Greene and Vermillion's Simplified Oral Hygiene Index (OHI-S). Whole saliva was collected under mechanical stimulation and evaluated salivary flow rate, initial pH, buffer capacity, and calcium and phosphate concentrations. The temperature of soft drinks, drinking method, sense of bitter taste, and other variables were also determined. Possible factors associated with DH were analyzed by univariate and multiple Poisson regression analyses. The prevalence ratio (PR) values and 95% confidence intervals (95% CI) were calculated.

RESULTS

DH was associated with the presence of dental erosion (PR; 95% CI = 2.23; 1.05 to 4.71) and salivary flow rate (2.49; 1.05 to 5.91). When the presence of erosion was not included, other variables were retained as follows: bitter taste (2.36; 1.38 to 4.03), OHI-S (0.47; 0.23 to 0.97).

CONCLUSION

DH in children is associated with factors related to dental erosion.

The effect of casein phosphopeptide-amorphous calcium phosphate paste and sodium fluoride mouthwash on the prevention of dentine erosion: An in vitro study

Aim:

The purpose was to compare the effect of 0.2% sodium fluoride mouthwash and casein phosphopeptide-amorphous calcium phosphate paste on prevention of dentin erosion.

Materials and Methods:

Buccal surfaces of 36 sound premolar teeth were ground flat and polished with abrasive discs. Half the polished surfaces were covered with tape to maintain a reference surface. Samples were randomly allocated into three groups. Group A was pretreated with tooth mousse (TM) 4 times a day for 5 days. Group B was pretreated with 0.2% sodium fluoride mouthwash 4 times a day for 5 days. Group C was considered as the control group with no pretreatment. In the next step, the samples were exposed to Coca-Cola 4 times a day for 3 days. After each erosive cycle, the samples were rinsed with deionized water and stored in artificial saliva. The surface loss was determined using profilometry.

Results:

The erosion in both Groups A and B was less than the control group. The surface loss in mouthwash group was significantly lower than in the control group. Erosion in TM group was more than the mouthwash group and less than the control group.

Conclusion:

Sodium fluoride mouthwash is more effective for prevention of dentin erosion.

Dental Erosion and Medical Conditions: An Overview of Aetiology, Diagnosis and Management

Tooth wear or tooth surface loss is a normal physiological process and occurs throughout life but is considered pathological when the degree of destruction is excessive or the rate of loss is rapid, causing functional, aesthetic or sensitivity problems. The importance of tooth wear as a dental problem has been increasingly recognized. The findings of a study in Trinidad indicate that the prevalence of tooth wear in a Trinidadian population is comparable to the United Kingdom (UK) and, indeed, that the level of moderate and severe wear is in fact nearly twice as high. The aetiology of tooth wear is attributed to four causes: erosion, attrition, abrasion and abfraction. Erosion is generally considered to be the most prevalent cause of tooth wear in the UK and Europe. Acids that cause dental erosion originate mainly from the diet or the stomach and to a lesser extent, the environment. Underlying medical problems can contribute to the progress of tooth wear due to erosion and the patient may not be aware of these conditions. Moderate to severe tooth wear poses a significant clinical challenge to dental practitioners and may result in treatment that is more complex and costly to the patient both in terms of finances and time spent in the dental chair. This paper provides an overview of aetiology and diagnosis of tooth wear, in particular tooth wear due to erosion, so that medical and dental practitioners may recognize tooth wear early, institute preventive measures and manage patients appropriately.

Is dental erosion really a problem?

Dental erosion is the non-carious dental substance loss induced by direct impact of exogenous or endogenous acids. It results in a loss of dental hard tissue, which can be serious in some groups, such as those with eating disorders, in patients with gastroesophageal reflux disease, and also in persons consuming high amounts of acidic drinks and foodstuffs. For these persons, erosion can impair their well-being, due to changes in appearance and/or loss of function of the teeth, e.g., the occurrence of hypersensitivity of teeth if the dentin is exposed. If erosion reaches an advanced stage, time- and money-consuming therapies may be necessary. The therapy, in turn, poses a challenge for the dentist, particularly if the defects are diagnosed at an advanced stage. While initial and moderate defects can mostly be treated non- or minimally invasively, severe defects often require complex therapeutic strategies, which often entail extensive loss of dental hard tissue due to preparatory measures. A major goal should therefore be to diagnose dental erosion at an early stage, to avoid functional and esthetic impairments as well as pain sensations and to ensure longevity of the dentition.