Ultrahydrophobic 3D/2D fluoroarene bilayer-based water-resistant perovskite solar cells with efficiencies exceeding 22

Super-Droplet-Repellent Carbon-Based Printable Perovskite Solar Cells

Despite attractive cost-effectiveness, scalability, and superior stability, carbon-based printable perovskite solar cells (CPSCs) still face moisture-induced degradation that limits their lifespan and commercial potential. Here, the moisture-preventing mechanisms of thin nanostructured super-repellent coating (advancing contact angle >167° and contact angle hysteresis 7°) integrated into CPSCs are investigated for different moisture forms (falling water droplets vs water vapor vs condensed water droplets). It is shown that unencapsulated super-repellent CPSCs have superior performance under continuous droplet impact for 12 h (rain falling experiments) compared to unencapsulated pristine (uncoated) CPSCs that degrade within seconds. Contrary to falling water droplets, where super-repellent coating serves as a shield, water vapor is found to physisorb through porous super-repellent coating (room temperature and relative humidity, RH 65% and 85%) that increase the CPSCs performance for 21% during ≈43 d similarly to pristine CPSCs. It is further shown that water condensation forms within or below the super-repellent coating (40 °C and RH 85%), followed by chemisorption and degradation of CPSCs. Because different forms of water have distinct effects on CPSC, it is suggested that future standard tests for repellent CPSCs should include rain falling and condensate formation tests. The findings will thus inspire the development of super-repellent coatings for moisture prevention.

Designing Surface Passivators Through Intramolecular Potential Manipulation for Efficient and Stable Perovskite Solar Cells

The conjugation of terminal ammonium salt groups with perovskite surfaces is a frequently employed technique that aims to enhance the overall performance of perovskite materials, encompassing both bulk and surface properties. Particularly, it exhibits heightened efficacy when applied to surface modification, due to its ability to mitigate defect accumulation and facilitate facile binding with the receptive sites inherent to the perovskite structure. However, the interaction of the bulk ammonium group with PbI2 has the potential to form a low-dimensional phase of perovskite, which may obstruct carrier extraction at the interface. Therefore, the surface passivators (MeO-PFACl) are designed through intramolecular potential manipulation. The combinations of the electron-donating methoxy group and π-π conjugation of the phenyl ring reduce the local potential at the reactive site of formamidinium group, making it less likely to form a low-dimension phase with perovskite. This surface passivation strategy effectively suppresses the surface nonradiative recombination and promotes the interface carrier extraction. The devices treated with MeO-PFACl have demonstrated exceptional performance, achieving a peak power conversion efficiency (PCE) of 25.88%, with an average PCE of 25.37%. These works offer a novel principle for enhancing both the efficiency and stability of PSCs using ammonium-incorporated molecules without the induction of an additional phase layer.

Manipulating Crystal Growth and Secondary Phase PbI2 to Enable Efficient and Stable Perovskite Solar Cells with Natural Additives

In perovskite solar cells (PSCs), the inherent defects of perovskite film and the random distribution of excess lead iodide (PbI2) prevent the improvement of efficiency and stability. Herein, natural cellulose is used as the raw material to design a series of cellulose derivatives for perovskite crystallization engineering. The cationic cellulose derivative C-Im-CN with cyano-imidazolium (Im-CN) cation and chloride anion prominently promotes the crystallization process, grain growth, and directional orientation of perovskite. Meanwhile, excess PbI2 is transferred to the surface of perovskite grains or formed plate-like crystallites in local domains. These effects result in suppressing defect formation, decreasing grain boundaries, enhancing carrier extraction, inhibiting non-radiative recombination, and dramatically prolonging carrier lifetimes. Thus, the PSCs exhibit a high power conversion efficiency of 24.71%. Moreover, C-Im-CN has multiple interaction sites and polymer skeleton, so the unencapsulated PSCs maintain above 91.3% of their initial efficiencies after 3000 h of continuous operation in a conventional air atmosphere and have good stability under high humidity conditions. The utilization of biopolymers with excellent structure-designability to manage the perovskite opens a state-of-the-art avenue for manufacturing and improving PSCs.

Superior Phonon-Limited Exciton Mobility in Lead-Free Two-Dimensional Perovskites

Tin-based two-dimensional (2D) perovskites are emerging as lead-free alternatives in halide perovskite materials, yet their exciton dynamics and transport remain less understood due to defect scattering. Addressing this, we employed temperature-dependent transient photoluminescence (PL) microscopy to investigate intrinsic exciton transport in three structurally analogous Sn- and Pb-based 2D perovskites. Employing conjugated ligands, we synthesized high-quality crystals with enhanced phase stability at various temperatures. Our results revealed phonon-limited exciton transport in Sn perovskites, with diffusion constants increasing from 0.2 cm2 s-1 at room temperature to 0.6 cm2 s-1 at 40 K, and a narrowing PL line width. Notably, Sn-based perovskites exhibited greater exciton mobility than their Pb-based equivalents, which is attributed to lighter effective masses. Thermally activated optical phonon scattering was observed in Sn-based compounds but was absent in Pb-based materials. These findings, supported by molecular dynamics simulations, demonstrate that the phonon scattering mechanism in Sn-based halide perovskites can be distinct from their Pb counterparts.

Frequency-selective perovskite photodetector for anti-interference optical communications

Free-space coupling, essential for various communication applications, often faces significant signal loss and interference from ambient light. Traditional methods rely on integrating complex optical and electronic systems, leading to bulkier and costlier communication equipment. Here, we show an asymmetric 2D-3D-2D perovskite structure device to achieve a frequency-selective photoresponse in a single device. By combining two electromotive forces of equal magnitude in the opposite directions, the device output is attenuated to zero under constant light illumination. Because these reverse photodiodes have different response speeds, the device only responds near a certain frequency, which can be tuned by manipulating the 2D perovskite components. The target device achieves an ultrafast response of 19.7/18.3 ns in the frequency-selective photoresponse range 0.8-9.7 MHz. This anti-interference photodetector can accurately transmit character and video data under strong light interference with a source intensity of up to 454 mW cm-2.

Moisture-Resilient Perovskite Solar Cells for Enhanced Stability

With the rapid rise in device performance of perovskite solar cells (PSCs), overcoming instabilities under outdoor operating conditions has become the most crucial obstacle toward their commercialization. Among stressors such as light, heat, voltage bias, and moisture, the latter is arguably the most critical, as it can decompose metal-halide perovskite (MHP) photoactive absorbers instantly through its hygroscopic components (organic cations and metal halides). In addition, most charge transport layers (CTLs) commonly employed in PSCs also degrade in the presence of water. Furthermore, photovoltaic module fabrication encompasses several steps, such as laser processing, subcell interconnection, and encapsulation, during which the device layers are exposed to the ambient atmosphere. Therefore, as a first step toward long-term stable perovskite photovoltaics, it is vital to engineer device materials toward maximizing moisture resilience, which can be accomplished by passivating the bulk of the MHP film, introducing passivation interlayers at the top contact, exploiting hydrophobic CTLs, and encapsulating finished devices with hydrophobic barrier layers, without jeopardizing device performance. Here, existing strategies for enhancing the performance stability of PSCs are reviewed and pathways toward moisture-resilient commercial perovskite devices are formulated.

Large-n quasi-phase-pure two-dimensional halide perovskite: A toolbox from materials to devices

Despite their excellent environmental stability, low defect density, and high carrier mobility, large-n quasi-two-dimensional halide perovskites (quasi-2DHPs) feature a limited application scope because of the formation of self-assembled multiple quantum wells (QWs) due to the similar thermal stabilities of large-n phases. However, large-n quasi-phase-pure 2DHPs (quasi-PP-2DHPs) can solve this problem perfectly. This review discusses the structures, formation mechanisms, and photoelectronic and physical properties of quasi-PP-2DHPs, summarises the corresponding single crystals, thin films, and heterojunction preparation methods, and presents the related advances. Moreover, we focus on applications of large-n quasi-PP-2DHPs in solar cells, photodetectors, lasers, light-emitting diodes, and field-effect transistors, discuss the challenges and prospects of these emerging photoelectronic materials, and review the potential technological developments in this area.

Defect passivation in methylammonium/bromine free inverted perovskite solar cells using charge-modulated molecular bonding

Molecular passivation is a prominent approach for improving the performance and operation stability of halide perovskite solar cells (HPSCs). Herein, we reveal discernible effects of diammonium molecules with either an aryl or alkyl core onto Methylammonium-free perovskites. Piperazine dihydriodide (PZDI), characterized by an alkyl core-electron cloud-rich-NH terminal, proves effective in mitigating surface and bulk defects and modifying surface chemistry or interfacial energy band, ultimately leading to improved carrier extraction. Benefiting from superior PZDI passivation, the device achieves an impressive efficiency of 23.17% (area ~1 cm2) (low open circuit voltage deficit ~0.327 V) along with superior operational stability. We achieve a certified efficiency of ~21.47% (area ~1.024 cm2) for inverted HPSC. PZDI strengthens adhesion to the perovskite via -NH2I and Mulliken charge distribution. Device analysis corroborates that stronger bonding interaction attenuates the defect densities and suppresses ion migration. This work underscores the crucial role of bifunctional molecules with stronger surface adsorption in defect mitigation, setting the stage for the design of charge-regulated molecular passivation to enhance the performance and stability of HPSC.

Single-Crystal-Assisted In Situ Phase Reconstruction Enables Efficient and Stable 2D/3D Perovskite Solar Cells

Perovskite solar cells (PSCs) that incorporate both two-dimensional (2D) and three-dimensional (3D) phases possess the potential to combine the high stability of 2D PSCs with the superior efficiency of 3D PSCs. Here, we demonstrated in situ phase reconstruction of 2D/3D perovskites using a 2D perovskite single-crystal-assisted method. A gradient phase distribution of 2D RP perovskites was formed after spin-coating a solution of the 2D Ruddlesden-Popper (RP) perovskite single crystal, (DFP)2PbI4, onto the 3D perovskite surface, followed by thermal annealing. The resulting film exhibits much reduced trap density, increased carrier mobility, and superior water resistance. As a result, the optimized 2D/3D PSCs achieved a champion efficiency of 24.87% with a high open-circuit voltage (VOC) of 1.185 V. This performance surpasses the control 3D perovskite device, which achieved an efficiency of 22.43% and a VOC of 1.129 V. Importantly, the unencapsulated device demonstrates significantly enhanced operational stability, preserving over 97% of its original efficiency after continuous light irradiation for 1500 h. Moreover, the extrapolated T80 lifetimes surpass 5700 h. These findings pave the way for rational regulation of the gradient phase distribution at the interface between 2D and 3D perovskites by employing 2D RP perovskite crystals to achieve stable and efficient PSCs.

Zirconium Doping to Enable High-Efficiency and Stable CsPbI2Br All-Inorganic Perovskite Solar Cells

All-inorganic wide-bandgap perovskite CsPbI2Br has attracted much attention because of its inherent thermal stability and ideal bandgap for the front subcell of tandem solar cells (TSCs). However, the low power conversion efficiency (PCE) and poor moisture stability of CsPbI2Br still restrict its future commercialization. Herein, zirconium tetrachloride (ZrCl4) was doped into CsPbI2Br films to modulate the crystal growth and improve the film quality. The partial substitution of the B-site Pb2+ of CsPbI2Br with Zr4+ suppresses the unwanted phase conversion from the crystallized black α-phase to the δ-phase, resulting in improved phase stability. Consequently, the humidity and thermal stability of the film are greatly improved. Additionally, the incorporation of ZrCl4 suppresses nonradiative recombination and forms a matched energy-level alignment with the hole-transport layer (Spiro-OMeTAD). Benefiting from these features, the ZrCl4-doped CsPbI2Br perovskite solar cell (PSC) shows an outstanding efficiency of 16.60% with a high open-circuit voltage of 1.29 V. The unencapsulated devices simultaneously show excellent humidity and thermal stability, retaining over 91% of PCEinitial after 1000 h of aging in ambient air conditions and 92% PCEinitial after 500 h of continuous heating at 85 °C in a nitrogen environment, respectively. Furthermore, ZrCl4-doped CsPbI2Br was employed as the front subcell of perovskite/organic TSCs and achieved a remarkable PCE of 19.42%, showing great potential for highly efficient and stable TSCs.

Recent Advances in Interface Engineering for Enhanced Open-Circuit Voltage Regulation in Perovskite Solar Cells

In recent years, perovskite solar cells (PSCs) have attracted significant attention due to their excellent photoelectric properties. However, several key performance parameters of these devices still fall short of their theoretical limits. Among these parameters, the regulation of open-circuit voltage (VOC ) has been a focal point of intensive research efforts, playing a pivotal role in advancing the efficiency of PSCs. This review first provides an overview of the generation and loss mechanism of VOC . It then discusses the significance of interface engineering in VOC regulation. Recent developments in high-efficiency PSCs realized via interface engineering have been summarized and categorized into three key areas: surface modification, interface structure optimization, and surface dimensional engineering. Finally, a comprehensive summary of past research in this domain and offered insights into the future prospects of enhancing VOC in PSCs is provided.

Bilayer 2D-3D Perovskite Heterostructures for Efficient and Stable Solar Cells

With a stacking-layered architecture, the bilayer two-dimensional-three-dimensional (2D-3D) perovskite heterostructure (PHS) not only eliminates surface defects but also protects the 3D perovskite matrix from external stimuli. However, these bilayer 2D-3D PHSs suffer from impaired interfacial charge carrier transport due to the relatively insulating 2D perovskite fragments with a random phase distribution. Over the past decade, substantial efforts have been devoted to pioneering molecular and structural designs of the 2D perovskite interlayers for improving their charge carrier mobility, which enables state-of-the-art perovskite solar cells with high power conversion efficiency and exceptional operational stability. Herein, this review offers a comprehensive and up-to-date overview on the recent progress of bilayer 2D-3D PHSs, encompassing advancements on spacer cation engineering, interfacial charge carrier modification, advanced deposition protocols, and characterization techniques. Then, the evolutionary trajectory of bilayer 2D-3D PHSs is outlined by summarizing its mainstream development trends, followed by a perspective discussion about its future research opportunities toward efficient and durable perovskite solar cells.

Uracil Induced Simultaneously Strengthening Grain Boundaries and Interfaces Enables High-Performance Perovskite Solar Cells with Superior Operational Stability

The operational stability is a huge obstacle to further commercialization of perovskite solar cells. To address this critical issue, in this work, uracil is introduced as a "binder" into the perovskite film to simultaneously improve the power conversion efficiency (PCE) and operational stability. Uracil can efficiently passivate defects and strengthen grain boundaries to enhance the stability of perovskite films. Moreover, the uracil also strengthens the interface between the perovskite and the Tin oxide (SnO2 ) electron transport layer to increase the binding force. The uracil-modified devices deliver a champion PCE of 24.23% (certificated 23.19%) with negligible hysteresis at active area of 0.0625 cm2 . In particular, the optimal device exhibits over 90% of its initial PCE after tracking for ≈6000 h at its maximum power point under continuous light, indicating its superior operational stability. Moreover, the devices also show great reproducibility in both PCE and operational stability.

Thermochromic Printable and Multicolor Polymeric Composite Based on Hybrid Organic-Inorganic Perovskite

Hybrid organic-inorganic perovskites (PVKs) are among the most promising materials for optoelectronic applications thanks to their outstanding photophysical properties and easy synthesis. Herein, a new PVK-based thermochromic composite is demonstrated. It can reversibly switch from a transparent state (transmittance > 80%) at room temperature to a colored state (transmittance < 10%) at high temperature, with very fast kinetics, taking only a few seconds to go from the bleached to the colored state (and vice versa). X-ray diffraction, Fourier-transform infrared spectroscopy, differential scanning calometry, rheological, and optical measurements carried out during heating/cooling cycles reveal that thermochromism in the material is based on a reversible process of PVK disassembly/assembly mediated by intercalating polymeric chains, through the formation and breaking of hydrogen bonds between polymer and perovskite. Therefore, differently from other thermochromic perovskites, that generally work with the adsorption/desorption of volatile molecules, the system is able to perform several heating/cooling cycles regardless of environmental conditions. The color and transition temperature (from 70 to 120 °C) can be tuned depending on the type of perovskite. Moreover, this thermochromic material is printable and can be deposited by cheap techniques, paving the way for a new class of smart coatings with an unprecedented range of colors.

Surface termination and strain-induced modulation of the structure and electronic properties in 2D perovskites (Cs2BCl4 & CsB2Cl5, B = Pb, Sn): a first-principles study

Two-dimensional (2D) halide perovskites have demonstrated impressive long-term stability and superior device performance as compared to their three-dimensional (3D) counterparts. The potential of 2D halide perovskites for advanced photovoltaic applications can be enhanced by an understanding of how external factors like strain could be used to tune their optoelectronic properties. This study explores the effects of biaxial strain on the structure and electronic transport properties of 2D halide perovskites, focusing on the lowest energy (001) surfaces of (Cs2BCl4 and CsB2Cl5, B = Pb or Sn) with CsCl and BCl2 terminations. Using first-principles calculations, we find that the lower energy CsCl terminated surface, resulting in Cs2BCl4, couples strongly with biaxial strain. This termination shows bandgap modulations from approximately 1.5 eV to 1.8 eV for Cs2PbCl4 and 1.2 eV to 1.5 eV for Cs2SnCl4 with biaxial strain. Within the acoustic deformation potential theory, we compute hole mobilities, and find substantial enhancements of approximately 80% for Pb-based and 50% for Sn-based systems, thereby emphasizing the potential of strain engineering to further optimize charge transport properties in 2D halide perovskites.

Operando dynamics of trapped carriers in perovskite solar cells observed via infrared optical activation spectroscopy

Conventional spectroscopies are not sufficiently selective to comprehensively understand the behaviour of trapped carriers in perovskite solar cells, particularly under their working conditions. Here we use infrared optical activation spectroscopy (i.e., pump-push-photocurrent), to observe the properties and real-time dynamics of trapped carriers within operando perovskite solar cells. We compare behaviour differences of trapped holes in pristine and surface-passivated FA0.99Cs0.01PbI3 devices using a combination of quasi-steady-state and nanosecond time-resolved pump-push-photocurrent, as well as kinetic and drift-diffusion models. We find a two-step trap-filling process: the rapid filling (~10 ns) of low-density traps in the bulk of perovskite, followed by the slower filling (~100 ns) of high-density traps at the perovskite/hole transport material interface. Surface passivation by n-octylammonium iodide dramatically reduces the number of trap states (~50 times), improving the device performance substantially. Moreover, the activation energy (~280 meV) of the dominant hole traps remains similar with and without surface passivation.

Eco-Friendly Boost for Perovskite Photovoltaics: Harnessing Cellulose-Modified SnO2 as a High-Performance Electron Transporting Material

In this study, a passivated tin oxide (SnO2) film is successfully obtained through the implementation of sodium carboxymethyl cellulose (Na-CMC) modifier agent and used as the electron transporting layer (ETL) within the assembly of perovskite solar cells (PSCs). The strategic incorporation of the Na-CMC modifier agent yields discernible enhancements in the optoelectronic properties of the ETL. Among the fabricated cells, the champion cell based on Na-CMC-complexed SnO2 ETL achieves a conversion efficiency of 22.2% with an open-circuit voltage (VOC) of 1.12 V, short-circuit current density (JSC) of 24.57 mA/cm2, and fill factor (FF) of 80.6%. On the other hand, these values are measured for the pristine SnO2 ETL-based control cell as VOC = 1.11 V, JSC = 23.59 mA/cm2, and FF = 76.7% with an efficiency of 20.1%. This improvement can be ascribed to the high charge extraction ability, higher optical transmittance, better conductivity, and decrease in the trap state density associated with the passivated ETL structure. In addition, the cells employing Na-CMC-complexed SnO2 ETL exhibit prolonged stability under ambient conditions during 2000 h. Based on the preliminary results, this study also presents a set of findings that could have substantial implications for the potential use of the Na-CMC molecule in both large-scale perovskite cells and perovskite/Si tandem configuration.

Fluorinated Cation-Based 2D Perovskites for Efficient and Stable 3D/2D Heterojunction Perovskite Solar Cells

Three-dimensional (3D) perovskite solar cells (PSCs) containing additives capable of forming two-dimensional (2D) structures in neat films have attracted attention due to their ability to enhance power conversion efficiency (PCE) in combination with improved operational stability. Herein, a newly designed fluorinated ammonium salt, 2-(perfluorophenyl)ethanaminium bromide:chloride50:50 (FEABr:Cl50:50), is introduced into CsMAFAPbI3-based PSCs with a standard n-i-p architecture. FEABr:Cl50:50 was used as an additive in the tin(IV) oxide (SnO2) electron transporting layer (ETL) as well as a surface treatment for the perovskite film. Used in this dual way, the additive was found to passivate charge-trapping defects within the SnO2 ETL and regulate the crystal growth of the perovskite layer. When FEABr:Cl50:50 was deposited onto the surface of the 3D perovskite film, it formed a thin hydrophobic 2D capping layer. Adopting this dual strategy led to the perovskite film having larger grain sizes, improved quality, and overall better device performance. As a result, the best-performing device exhibited a PCE of over 23% with negligible hysteresis in an n-i-p device architecture with an area of 0.2 cm2. Furthermore, unencapsulated devices with the hydrophobic 2D capping layer showed improved stability compared to the control device when measured under continuous light irradiation at a maximum power point (MPP) at 80 ± 5 °C in a humid (≈50%) environment.

Characterizing Spatial and Energetic Distributions of Trap States Toward Highly Efficient Perovskite Photovoltaics

Due to their greater opt electric performance, perovskite photovoltaics (PVs) present huge potential to be commercialized. Perovskite PV's high theoretical efficiency expands the available development area. The passivation of defects in perovskite films is crucial for approaching the theoretical limit. In addition to creating efficient passivation techniques, it is essential to direct the passivation approach by getting precise and real-time information on the trap states through measurements. Therefore, it is necessary to establish quantitative characterization methods for the trap states in energy and 3D spaces. The authors cover the characterization of the spatial and energy distributions of trap states in this article with an eye toward high-efficiency perovskite photovoltaics. After going over the strategies that have been created for characterizing and evaluating trap states, the authors will concentrate on how to direct the creative development of characterization techniques for trap states assessment and highlight the opportunities and challenges of future development. The 3D space and energy distribution mappings of trap states are anticipated to be realized. The review will give key guiding importance for further approaching the theoretical efficiency of perovskite photovoltaics, offering some future research direction and technological assistance for the development of appropriate targeted passivation technologies.

Scalable All-Inorganic Halide Perovskite Photoanodes with >100 h Operational Stability Containing Earth-Abundant Materials

The application of halide perovskites in the photoelectrochemical generation of solar fuels and feedstocks is hindered by the instability of perovskites in aqueous electrolytes and the use of expensive electrode and catalyst materials, particularly in photoanodes driving kinetically slow water oxidation. Here, solely earth-abundant materials are incorporated to fabricate a CsPbBr3 -based photoanode that reaches a low onset potential of +0.4 VRHE and 8 mA cm-2 photocurrent density at +1.23 VRHE for water oxidation, close to the radiative efficiency limit of CsPbBr3 . This photoanode retains 100% of its stabilized photocurrent density for more than 100 h of operation by replacing once the inexpensive graphite sheet upon signs of deterioration. The improved performance is due to an efficiently electrodeposited NiFeOOH catalyst on a protective self-adhesive graphite sheet, and enhanced charge transfer achieved by phase engineering of CsPbBr3 . Devices with >1 cm2 area, and low-temperature processing demonstrate the potential for low capital cost, stable, and scalable perovskite photoanodes.

Mechanism of the Anomalous Dependence between Spin-Orbit Coupling and Dimensionality in Lead Halide Perovskites

The spin-orbit coupling (SOC) effect of lead (Pb) atoms is a consequential attribute of the unique optoelectronic and defect properties of lead halide perovskites (LHPs). It has been found that the SOC effect varies significantly as the structural dimensionality changes with an anomalous dependence; i.e., while the SOC strength monotonically decreases as structural dimensionality decreases from three-dimensional (3D) to two-dimensional (2D) and then to one-dimensional (1D), the zero-dimensional (0D) SOC strength is greater than the 1D SOC strength. The underlying mechanism of such a SOC dimensionality dependence anomaly remains elusive. In this work, we show that Pb 6p energy splitting increases from 3D to 2D and to 1D LHPs due to the increased degree of distortion, leading to a reduced SOC strength. However, the degree of distortion decreases for the 1D to 0D transformation, resulting in reverse SOC enhancement. The mechanism described in this work can be employed to regulate the SOC effect in the design of perovskite materials.

Dual-Interface Modulation with Covalent Organic Framework Enables Efficient and Durable Perovskite Solar Cells

Dual-interface modulation including buried interface as well as the top surface has recently been proven to be crucial for obtaining high photovoltaic performance in lead halide perovskite solar cells (PSCs). Herein, for the first time, the strategy of using functional covalent organic frameworks (COFs), namely HS-COFs for dual-interface modulation, is reported to further understand its intrinsic mechanisms in optimizing the bottom and top surfaces. Specifically, the buried HS-COFs layer can enhance the resistance against ultraviolet radiation, and more importantly, release the tensile strain, which is beneficial for enhancing device stability and improving the order of perovskite crystal growth. Furthermore, the detailed characterization results reveal that the HS-COFs on the top surface can effectively passivate the surface defects and suppress non-radiation recombination, as well as optimize the crystallization and growth of the perovskite film. Benefiting from the synergistic effects, the dual-interface modified devices deliver champion efficiencies of 24.26% and 21.30% for 0.0725 cm2 and 1 cm2 -sized devices, respectively. Moreover, they retain 88% and 84% of their initial efficiencies after aging for 2000 h under the ambient conditions (25 °C, relative humidity: 35-45%) and a nitrogen atmosphere with heating at 65 °C, respectively.

Visualizing Interfacial Energy Offset and Defects in Efficient 2D/3D Heterojunction Perovskite Solar Cells and Modules

Currently, the full potential of perovskite solar cells (PSCs) is limited by chargecarrier recombination owing to imperfect passivation methods. Here, the recombination loss mechanisms owing to the interfacial energy offset and defects are quantified. The results show that a favorable energy offset can reduce minority carriers and suppress interfacial recombination losses more effectively than chemical passivation. To obtain high-efficiency PSCs, 2D perovskites are promising candidates, which offer powerful field effects and require only modest chemical passivation at the interface. The enhanced passivation and charge-carrier extraction offered by the 2D/3D heterojunction PSCs has boosted their power conversion efficiency to 25.32% (certified 25.04%) for small-size devices and to 21.48% for a large-area module (with a designated area of 29.0 cm2 ). Ion migration is also suppressed by the 2D/3D heterojunction, such that the unencapsulated small-size devices maintain 90% of their initial efficiency after 2000 h of continuous operation at the maximum power point.

Tailoring passivators for highly efficient and stable perovskite solar cells

There is an ongoing global effort to advance emerging perovskite solar cells (PSCs), and many of these endeavours are focused on developing new compositions, processing methods and passivation strategies. In particular, the use of passivators to reduce the defects in perovskite materials has been demonstrated to be an effective approach for enhancing the photovoltaic performance and long-term stability of PSCs. Organic passivators have received increasing attention since the late 2010s as their structures and properties can readily be modified. First, this Review discusses the main types of defect in perovskite materials and reviews their properties. We examine the deleterious impact of defects on device efficiency and stability and highlight how defects facilitate extrinsic degradation pathways. Second, the proven use of different passivator designs to mitigate these negative effects is discussed, and possible defect passivation mechanisms are presented. Finally, we propose four specific directions for future research, which, in our opinion, will be crucial for unlocking the full potential of PSCs using the concept of defect passivation.

Synergy of 3D and 2D Perovskites for Durable, Efficient Solar Cells and Beyond

Three-dimensional (3D) organic-inorganic lead halide perovskites have emerged in the past few years as a promising material for low-cost, high-efficiency optoelectronic devices. Spurred by this recent interest, several subclasses of halide perovskites such as two-dimensional (2D) halide perovskites have begun to play a significant role in advancing the fundamental understanding of the structural, chemical, and physical properties of halide perovskites, which are technologically relevant. While the chemistry of these 2D materials is similar to that of the 3D halide perovskites, their layered structure with a hybrid organic-inorganic interface induces new emergent properties that can significantly or sometimes subtly be important. Synergistic properties can be realized in systems that combine different materials exhibiting different dimensionalities by exploiting their intrinsic compatibility. In many cases, the weaknesses of each material can be alleviated in heteroarchitectures. For example, 3D-2D halide perovskites can demonstrate novel behavior that neither material would be capable of separately. This review describes how the structural differences between 3D halide perovskites and 2D halide perovskites give rise to their disparate materials properties, discusses strategies for realizing mixed-dimensional systems of various architectures through solution-processing techniques, and presents a comprehensive outlook for the use of 3D-2D systems in solar cells. Finally, we investigate applications of 3D-2D systems beyond photovoltaics and offer our perspective on mixed-dimensional perovskite systems as semiconductor materials with unrivaled tunability, efficiency, and technologically relevant durability.

Engineering ligand reactivity enables high-temperature operation of stable perovskite solar cells

Perovskite solar cells (PSCs) consisting of interfacial two- and three-dimensional heterostructures that incorporate ammonium ligand intercalation have enabled rapid progress toward the goal of uniting performance with stability. However, as the field continues to seek ever-higher durability, additional tools that avoid progressive ligand intercalation are needed to minimize degradation at high temperatures. We used ammonium ligands that are nonreactive with the bulk of perovskites and investigated a library that varies ligand molecular structure systematically. We found that fluorinated aniliniums offer interfacial passivation and simultaneously minimize reactivity with perovskites. Using this approach, we report a certified quasi-steady-state power-conversion efficiency of 24.09% for inverted-structure PSCs. In an encapsulated device operating at 85°C and 50% relative humidity, we document a 1560-hour T₈₅ at maximum power point under 1-sun illumination.

Managing Interfacial Defects and Carriers by Synergistic Modulation of Functional Groups and Spatial Conformation for High-Performance Perovskite Photovoltaics Based on Vacuum Flash Method

Interfacial nonradiative recombination loss is a huge barrier to advance the photovoltaic performance. Here, one effective interfacial defect and carrier dynamics management strategy by synergistic modulation of functional groups and spatial conformation of ammonium salt molecules is proposed. The surface treatment with 3-ammonium propionic acid iodide (3-APAI) does not form 2D perovskite passivation layer while the propylammonium ions and 5-aminopentanoic acid hydroiodide post-treatment lead to the formation of 2D perovskite passivation layers. Due to appropriate alkyl chain length, theoretical and experimental results manifest that COOH and NH₃ ⁺ groups in 3-APAI molecules can form coordination bonding with undercoordinated Pb²⁺ and ionic bonding and hydrogen bonding with octahedron PbI₆ ^4- , respectively, which makes both groups be simultaneously firmly anchored on the surface of perovskite films. This will strengthen defect passivation effect and improve interfacial carrier transport and transfer. The synergistic effect of functional groups and spatial conformation confers 3-APAI better defect passivation effect than 2D perovskite layers. The 3-APAI-modified device based on vacuum flash technology achieves an alluring peak efficiency of 24.72% (certified 23.68%), which is among highly efficient devices fabricated without antisolvents. Furthermore, the encapsulated 3-APAI-modified device degrades by less than 4% after 1400 h of continuous one sun illumination.

Air-Processable Perovskite Solar Cells by Hexamine Molecule Phase Stabilization

Perovskite solar cells have emerged as a potential energy alternative due to their low cost of fabrication and high power conversion efficiency. Unfortunately, their poor ambient stability has critically limited their industrialization and application in real environmental conditions. Here, we show that by introducing hexamine molecules into the perovskite lattice, we can enhance the photoactive phase stability, enabling high-performance and air-processable perovskite solar cells. The unencapsulated and freshly prepared perovskite solar cells produce a power conversion efficiency of 16.83% under a 100 mW cm^-2 1.5G solar light simulator and demonstrate high stability properties when being stored for more than 1500 h in humid air with relative humidity ranging from 65 to 90%. We envisage that our findings may revolutionize perovskite solar cell research, pushing the performance and stability to the limit and bringing the perovskite solar cells toward industrialization.

Controlling Phase Transitions in Two-Dimensional Perovskites through Organic Cation Alloying

We demonstrate control over the phase transition temperature of Ruddlesden-Popper two-dimensional (2D) perovskites by alloying alkyl organic cations of varying lengths. By blending hexylammonium with pentylammonium or heptylammonium cations in different ratios, we continuously tune the phase transition temperature of 2D perovskites from approximately 40 to -80 °C in both crystalline powders and thin films. Correlating temperature-dependent grazing incidence wide-angle X-ray scattering and photoluminescence spectroscopy, we also demonstrate that the phase transition in the organic layer couples to the inorganic lattice, impacting PL intensity and wavelength. We take advantage of changes in PL intensity to image the dynamics of this phase transition and show asymmetric phase growth at the microscale. Our findings provide the necessary design principles to precisely control phase transitions in 2D perovskites for applications such as solid-solid phase change materials and barocaloric cooling.

Topotactic, Vapor-Phase, In Situ Monitored Formation of Ultrathin, Phase-Pure 2D-on-3D Halide Perovskite Surfaces

Two-dimensional (2D) halide perovskites, HaPs, can provide chemical stability to three-dimensional (3D) HaP surfaces, protecting them from exposure to ambient species and from reacting with contacting layers. Both actions occur with 2D HaPs, with the general stoichiometry R₂PbI₄ (R: long or bulky organic amine) covering the 3D ones. Adding such covering films can also boost power conversion efficiencies of photovoltaic cells by passivating surface/interface trap states. For maximum benefit, we need conformal ultrathin and phase-pure (n = 1) 2D layers to enable efficient tunneling of photogenerated charge carriers through the 2D film barrier. Conformal coverage of ultrathin (<10 nm) R₂PbI₄ layers on 3D perovskites is challenging with spin coating; even more so is its upscaling for larger-area devices. We report on vapor-phase cation exchange of the 3D surface with the R₂PbI₄ molecules and real-time in situ growth monitoring by photoluminescence (PL) to determine limits for forming ultrathin 2D layers. We characterize the 2D growth stages, following the changing PL intensity-time profiles, by combining structural, optical, morphological, and compositional characterizations. Moreover, from quantitative X-ray photoelectron spectroscopy (XPS) analysis on 2D/3D bilayer films, we estimate the smallest width of a 2D cover that we can grow to be <5 nm, roughly the limit for efficient tunneling through a (semi)conjugated organic barrier. We also find that, besides protecting the 3D against ambient humidity-induced degradation, the ultrathin 2D-on-3D film also aids self-repair following photodamage.

Spontaneous Internal Encapsulation via Dual Interfacial Perovskite Heterojunction Enables Highly Efficient and Stable Perovskite Solar Cells

Deep traps stemming from the defects formed at the surfaces and grain boundaries of the perovskite films are the main reasons of nonradiative recombination and material degradation, which significantly affect efficiency and stability of perovskite solar cells (PSCs). Here, a spontaneous internal encapsulation strategy was developed by constructing a dual interfacial perovskite heterojunction at the top and buried interface of the three-dimensional (3D) perovskite film. The spacer cations of the two-dimensional (2D) perovskite structure interacted strongly with the 3D perovskite to passivate the defects and optimize the energy level alignment. Meanwhile, the interfacial perovskite heterojunction underearth delayed the crystallization speed and improved the crystallization quality of the upper 3D perovskite. Thanks to these positive effects, the PSC exhibited a power conversion efficiency of 22.92% with good reproducibility. Significantly, the unencapsulated device with the dual interfacial perovskite heterojunction maintained 88% of its initial efficiency after 2900 h under 65 ± 5% RH in air.

3D Perovskite Passivation with a Benzotriazole-Based 2D Interlayer for High-Efficiency Solar Cells

2H-Benzotriazol-2-ylethylammonium bromide and iodide and its difluorinated derivatives are synthesized and employed as interlayers for passivation of formamidinium lead triiodide (FAPbI₃) solar cells. In combination with PbI₂ and PbBr₂, these benzotriazole derivatives form two-dimensional (2D) Ruddlesden-Popper perovskites (RPPs) as evidenced by their crystal structures and thin film characteristics. When used to passivate n-i-p FAPbI₃ solar cells, the power conversion efficiency improves from 20% to close to 22% by enhancing the open-circuit voltage. Quasi-Fermi level splitting experiments and scanning electron microscopy cathodoluminescence hyperspectral imaging reveal that passivation provides a reduced nonradiative recombination at the interface between the perovskite and hole transport layer. Photoluminescence spectroscopy, angle-resolved grazing-incidence wide-angle X-ray scattering, and depth profiling X-ray photoelectron spectroscopy studies of the 2D/three-dimensional (3D) interface between the benzotriazole RPP and FAPbI₃ show that a nonuniform layer of 2D perovskites is enough to passivate defects, enhance charge extraction, and decrease nonradiative recombination.

3D/2D Core/Shell Perovskite Nanocrystals for High-Performance Solar Cells

All-inorganic lead halide perovskite nanocrystals (NCs) emerge as a rising star in photovoltaic fields on account of their excellent optoelectronic properties. However, it still remains challenging to further promote photovoltaic efficiency due to the susceptible surface and inevitable vacancies. Here, this work reports a 3D/2D core/shell perovskite heterojunction based on CsPbI₃ NCs and its performance in solar cells. The guanidinium (GA⁺ ) rich 2D nanoshells can significantly passivate surface trap states and lower the capping ligand density, resulting in improved photoelectric properties and carrier transport and diminished nonradiative recombination centers via the hydrogen bonds from amino groups in GA⁺ ions. Consequently, an outstanding power conversion efficiency (PCE) of up to 15.53% is realized, substantially higher than the control device (13.77%). This work highlights the importance of surface chemistry and offers a feasible avenue to achieve high-performance perovskite NCs-based optoelectronic devices.

Highly Efficient and Stable 2D/3D Heterojunction Perovskite Solar Cells by In Situ Interface Modification with [(p-Fluorophenyl)ethyl]ammonium Acetate

2D/3D heterojunction perovskites, meaning a rationally prepared 2D capping layer on 3D perovskite films, have been demonstrated as an effective avenue for simultaneously enhancing the efficiency and stability in perovskite solar cells (PSCs). However, the mechanism of the 2D perovskite induced by organic agents is still not extensively studied. Here, we report 2D/3D heterojunction PSCs by in situ fabricating a 2D modified layer on 3D perovskite films with [(p-fluorophenyl)ethyl]ammonium acetate (FPEAAc). During the annealing process, FPEAAc melts and uniformly covers the 3D perovskite films. Then, the excess acetate salt is volatilized, eventually forming a compact 2D perovskite thin layer. On the one hand, the organic agents can effectively rivet onto the 3D perovskite surface, ensuring formation of the necessary 2D perovskites with hydrophobic FPEA⁺ ions. On the other hand, the reaction generates some PbI₂, which passivates the defects on 3D perovskite films and improves the interface contact, significantly enhancing the open-circuit voltage (V_OC) and fill factor (FF) in 2D/3D PSCs. The highest power conversion efficiency of 22.53% is achieved compared with 20.16% in 3D PSCs. The 2D/3D-heterojunction-structured PSCs modified by FPEAAc exhibit high stability, retaining about 90% of the initial device efficiency after 500 h at 85 °C and 40 ± 5% relative humidity. Our research provides a simple method to control the 2D perovskite layer formation and effectively enhance the performance and stability in 2D/3D heterojunction perovskite cells.

Regioselective Multisite Atomic-Chlorine Passivation Enables Efficient and Stable Perovskite Solar Cells

Passivating defects using organic halide salts, especially chlorides, is an effective method to improve power conversion efficiencies (PCEs) of perovskite solar cells (PSCs) arising from the stronger Pb-Cl bonding than Pb-I and Pb-Br bonding. However, Cl^- anions with a small radius are prone to incorporation into the perovskite lattice that distorts the lead halide octahedron, degrading the photovoltaic performance. Here, we substitute atomic-Cl-containing organic molecules for widely used ionic-Cl salts, which not only retain the efficient passivation by Cl but also prevent the incorporation of Cl into the bulk lattice, benefiting from the strong covalent bonding between Cl atoms and organic frameworks. We find that only when the distance of Cl atoms in single molecules matches well with the distance of halide ions in perovskites can such a configuration maximize the defect passivation. We thereby optimize the molecular configuration to enable multiple Cl atoms in an optimal spatial position to maximize their binding with surface defects. The resulting PSCs achieve a certified PCE of 25.02%, among the highest PCEs for PSCs, and retain 90% of their initial PCE after 500 h of continuous operation.

Highly Sensitive Tin-Lead Perovskite Photodetectors with Over 450 Days Stability Enabled by Synergistic Engineering for Pulse Oximetry System

Low-bandgap tin (Sn)-lead (Pb) halide perovskites can achieve near-infrared response for photodetectors. However, the Sn-based devices suffer from notorious instability and high defect densities due to the oxidation propensity of Sn²⁺ . Herein, a multifunctional additive 4-amino-2,3,5,6-tetrafluorobenzoic acid (ATFBA) is presented, which can passivate surface defects and inhibit the oxidation of Sn²⁺ through hydrogen bonds and chelation coordination from the terminal amino and carboxyl groups. The perfluorinated benzene ring structure of ATFBA affords the passivator assembled at the grain boundaries to enhance the water resistance. With the synergistical passivation of these functional groups, the Sn-Pb perovskite photodetector exhibits a remarkable responsivity of 0.52 A W^-1 and an excellent specific detectivity of 5.34 × 10¹² Jones at 850 nm, along with remaining 97% of its initial responsivity over 450 days. Benefitting from high sensitivity, the photodetector is integrated into a pulse oximetry sensor visualization system, yielding accurate blood oxygen saturation and heart rate with less than 2% error. This work paves the avenue toward constructing high-performance and stable Sn-Pb perovskite photodetectors for practical applications.

Roles that Organic Ammoniums Play on the Surface of the Perovskite Film: A Review

The roles of organic ammonium salts (OASs) which are widely used for the surface treatment of the perovskite film, including formation of 2D perovskites, direct surface passiviation, and other effects, have been reviewed. The influencing factors for these roles of OASs are also discussed, which are important for improved efficiency and stability of perovskite solar cells. More information can be found in the Review article by X. Guo and co-workers. (DOI: 10.1002/chem.202203001).

Managing Secondary Phase Lead Iodide in Hybrid Perovskites via Surface Reconstruction for High-Performance Perovskite Solar Cells with Robust Environmental Stability

Rationally managing the secondary-phase excess lead iodide (PbI₂ ) in hybrid perovskite is of significance for pursuing high performance perovskite solar cells (PSCs), while the challenge remains on its conversion to a homogeneous layer that is robust stable against environmental stimuli. We herein demonstrate an effective strategy of surface reconstruction that converts the excess PbI₂ into a gradient lead sulfate-silica bi-layer, which substantially stabilizes the perovskite film and reduces interfacial charge transfer barrier in the PSCs device. The perovskite films with such bi-layer could bear harsh conditions such as soaking in water, light illumination at 70 % relative humidity, and the damp-thermal (85 °C and 30 % humidity) environment. The resulted PSCs deliver a champion efficiency up to 24.09 %, as well as remarkable environmental stability, e.g., retaining 78 % of their initial efficiency after 5500 h of shelf storage, and 82 % after 1000 h of operational stability testing.

Boosting Charge Transport in a 2D/3D Perovskite Heterostructure by Selecting an Ordered 2D Perovskite as the Passivator

We demonstrate that an ordered 2D perovskite can significantly boost the photoelectric performance of 2D/3D perovskite heterostructures. Using selective fluorination of phenyl-ethyl ammonium (PEA) lead iodide to passivate 3D FA_0.8 Cs_0.2 PbI₃ , we find that the 2D/3D perovskite heterostructures passivated by a higher ordered 2D perovskite have lower Urbach energy, yielding a remarkable increase in photoluminescence (PL) intensity, PL lifetime, charge-carrier mobilities (ϕμ), and carrier diffusion length (L_D ) for a certain 2D perovskite content. High performance with an ultralong PL lifetime of ≈1.3 μs, high ϕμ of ≈18.56 cm²  V^-1  s^-1 , and long L_D of ≈7.85 μm is achieved in the 2D/3D films when passivated by 16.67 % para-fluoro-PEA₂ PbI₄ . This carrier diffusion length is comparable to that of some perovskite single crystals (>5 μm). These findings provide key missing information on how the organic cations of 2D perovskites influence the performance of 2D/3D perovskite heterostructures.

Elucidating the Origins of High Preferential Crystal Orientation in Quasi-2D Perovskite Solar Cells

Incorporating large organic cations to form 2D and mixed 2D/3D structures significantly increases the stability of perovskite solar cells. However, due to their low electron mobility, aligning the organic sheets to ensure unimpeded charge transport is critical to rival the high performances of pure 3D systems. While additives such as methylammonium chloride (MACl) can enable this preferential orientation, so far, no complete description exists explaining how they influence the nucleation process to grow highly aligned crystals. Here, by investigating the initial stages of the crystallization, as well as partially and fully formed perovskites grown using MACl, the origins underlying this favorable alignment are inferred. This mechanism is studied by employing 3-fluorobenzylammonium in quasi-2D perovskite solar cells. Upon assisting the crystallization with MACl, films with a degree of preferential orientation of 94%, capable of withstanding moisture levels of 97% relative humidity for 10 h without significant changes in the crystal structure are achieved. Finally, by combining macroscopic, microscopic, and spectroscopic studies, the nucleation process leading to highly oriented perovskite films is elucidated. Understanding this mechanism will aid in the rational design of future additives to achieve more defect tolerant and stable perovskite optoelectronics.

Interfacial Engineering of Au@Nb2CTx-MXene Modulates the Growth Strain, Suppresses the Auger Recombination, and Enables an Open-Circuit Voltage of over 1.2 V in Perovskite Solar Cells

Defects at the interface of charge transport layers can cause severe charge accumulation and poor charge transferability, which greatly affect the efficiency and stability of stannic oxide (SnO₂)-based perovskite solar cells (PSCs). Herein, a new type of MXene (Nb₂CT_x-MXene) is applied to the interface of SnO₂ layers to passivate the interfacial defects and promote charge transport. Nb₂CT_x-MXene in PSCs realizes the role of boosting the conductivity, reducing the tin vacancies in the interstitial void of the SnO₂ layer, decreasing the defect density, and aligning the bandgap. Afterward, Nb₂CT_x-MXene is decorated with gold nanospheres, which has the ability to modulate the tensile strain of perovskites and suppress the Auger recombination. Eventually, the Au@Nb₂CT_x-MXene-modified device yields an excellent power conversion efficiency (PCE) of 23.78% with a relatively high open-circuit voltage of 1.215 V (E_g ∼ 1.60 eV). The unencapsulated devices maintain 90% of their initial PCE values after storage in the air with a relative humidity of 40% for 1000 h and remain above 80% of their initial efficiency after operation at the maximum power point for 500 h under 1 sun illumination. Our work provides an avenue to fabricate high-efficiency and stable PSCs with MXene adapting to commercial development.

Upscaling of Carbon-Based Perovskite Solar Module

Perovskite solar cells (PSCs) and modules are driving the energy revolution in the coming photovoltaic field. In the last 10 years, PSCs reached efficiency close to the silicon photovoltaic technology by adopting low-cost solution processes. Despite this, the noble metal (such as gold and silver) used in PSCs as a counter electrode made these devices costly in terms of energy, CO₂ footprint, and materials. Carbon-based perovskite solar cells (C-PSCs) and modules use graphite/carbon-black-based material as the counter electrode. The formulation of low-cost carbon-based inks and pastes makes them suitable for large area coating techniques and hence a solid technology for imminent industrialization. Here, we want to present the upscaling routes of carbon-counter-electrode-based module devices in terms of materials formulation, architectures, and manufacturing processes in order to give a clear vision of the scaling route and encourage the research in this green and sustainable direction.

Big data driven perovskite solar cell stability analysis

During the last decade lead halide perovskites have shown great potential for photovoltaic applications. However, the stability of perovskite solar cells still restricts commercialization, and lack of properly implemented unified stability testing and disseminating standards makes it difficult to compare historical stability data for evaluating promising routes towards better device stability. Here, we propose a single indicator to describe device stability that normalizes the stability results with respect to different environmental stress conditions which enables a direct comparison of different stability results. Based on this indicator and an open dataset of heterogeneous stability data of over 7000 devices, we have conducted a statistical analysis to assess the effect of different stability improvement strategies. This provides important insights for achieving more stable perovskite solar cells and we also provide suggestions for future directions in the perovskite solar cell field based on big data utilization.

Chelate Coordination Strengthens Surface Termination to Attain High-Efficiency Perovskite Solar Cells

Solar cell efficiency and stability are two key metrics to determine whether a photovoltaic device is viable for commercial applications. The surface termination of the perovskite layer plays a pivotal role in not only the photoelectric conversion efficiency (PCE) but also the stability of assembled perovskite solar cells (PSCs). Herein, a strong chelate coordination bond is designed to terminate the surface of the perovskite absorber layer. On the one hand, the ligand anions bind with Pb cations via a bidentate chelating bond to restrict the ion migration, and the chelate surface termination changes the surface from hydrophilic to hydrophobic. Both are beneficial to improving the long-term stability. On the other hand, the formation of the chelating bonding effectively eliminates the deep-level defects including Pb_I and Pb clusters on the Pb-I and FA-I terminations, respectively, as confirmed by theoretical simulation and experimental results. Consequently, the PCE is increased to 24.52%, open circuit voltage to 1.19 V, and fill factor to 81.53%; all three are among the highest for hybrid perovskite cells. The present strategy provides a straightforward means to enhance both the PCE and long-term stability of PSCs.

Underlying Interface Defect Passivation and Charge Transfer Enhancement via Sulfonated Hole-Transporting Materials for Efficient Inverted Perovskite Solar Cells

To date, numbers of polymeric hole-transporting materials (HTMs) have been developed to improve interfacial charge transport to achieve high-performance inverted perovskite solar cells (PSCs). However, molecular design for passivating the underlying surface defects between perovskite and HTMs is a neglected issue, which is a major bottleneck to further enhance the performance of the inverted devices. Herein, we design and synthesize a new polymeric HTM PsTA-mPV with the methylthiol group, in which a lone pair of electrons of sulfur atoms can passivate the underlying interface defects of the perovskite more efficiently by coordinating Pb²⁺ vacancies. Furthermore, PsTA-mPV exhibits a deeper highest occupied molecular orbital (HOMO) level aligned with perovskite due to the π-acceptor capability of sulfur, which improves interfacial charge transfer between perovskite and the HTM layer. Using PsTA-mPV as a dopant-free HTM, the inverted PSCs show 20.2% efficiency and long-term stability, which is ascribed to surface defect passivation, well energy-level matching with perovskite, and efficient charge extraction.

Oriented Crystal Growth during Perovskite Surface Reconstruction

Surface passivation has become a key strategy for an improvement in power conversion efficiency (PCE) of perovskite solar cells (PSCs) since PSCs experienced a steep increase in PCE and reached a comparably matured point. Recently, surface passivation using a mixed salt of fluorinated alkyl ammonium iodide and formamidinium bromide demonstrated a remarkable improvement in both performance and stability, which can be tuned by the length of the alkyl chain. Nevertheless, the role of the alkyl chain in manipulating surface-limited crystal growth was not fully understood, preventing a further progress in interface control. In this study, we found that the length of the fluorine-substituted alkyl chain governed the crystal formation dynamics by manipulating surface tensions of different crystal orientations. The overall enhancement of the (001) plane, being the most favored, commonly resulted from the surface reformation of the perovskite film regardless of the chain length, while the highly oriented (001) over (111) was monitored with a particular chain length. The enhanced crystal orientation during surface recrystallization was responsible for the low trap density and thus effectively suppressed charge recombination at the interface, resulting in a considerable increase in open-circuit voltage and fill factor.

Perfluoroarenes: A Versatile Platform for Hybrid Perovskite Photovoltaics

The instability of hybrid organic-inorganic halide perovskites presents one of the pressing challenges for their application. This is associated with the sensitivity to moisture as well as mixed ionic-electronic conductivity that leads to enhanced ion migration under conditions of voltage and light bias. Some of the most effective strategies to stabilize hybrid perovskite materials during operation involve the use of interfacial molecular assemblies and low-dimensional perovskite architectures based on hydrophobic organic moieties that could suppress the effects of moisture or ion migration. For this purpose, perfluoroarenes have provided a versatile platform due to their enhanced hydrophobicity as well as the capacity to engage in various noncovalent interactions that affect the characteristics of the resulting assemblies as well as ion migration. This Perspective discusses the emerging role of perfluoroarenes in stabilizing hybrid perovskite materials and their photovoltaic devices through different modes of action, offering insights for the design of advanced materials.

Bio-Inspired Graphitic Carbon-Based Large-Area (10 × 10 cm2) Perovskite Solar Cells: Stability Assessments under Indoor, Outdoor, and Water-Soaked Conditions

In the emerging photovoltaic (PV) technologies, the golden triangle rule includes higher efficiency, longevity (or stability), and low cost, which are the foremost criteria for the root of commercial feasibility. Accordingly, a unique low-cost, ecofriendly, all-solution-processed, "bio-inspired" graphitic carbon (extracted from the most invasive plant species of Eichhornia crassipes: listed as one of the 100 most dangerous species by the International Union for Conservation of Nature) and a mixed halide perovskite interface-engineered, unique single-cell large-scale (10 × 10 sq.cm with an active area of 88 cm²) carbon-based perovskite solar cell (C-PSC) are demonstrated for the first time, delivering a maximum PCE of 6.32%. Notable performance was observed under low light performance for the interface-engineered champion device fabricated using the layer-to-layer approach, which, even when tested under fluorescent room light condition (at 200 lux of about ∼0.1 SUN illumination), exhibited a significant PCE. In terms of addressing the stability issues in the fabricated PSC devices, the present work has adopted a two-step strategy: the instability toward the extrinsic factors is addressed by encapsulation, and the subsequent intrinsic instability issue is also addressed through interfacial engineering. Surprisingly, when tested under various stability conditions (STC) such as ambient air, light (continuous 1 SUN, under room light illumination (0.1 SUN) and direct sunlight), severe damp up to a depth of ∼25 mm water (cold (∼15 °C) and hot (∼65 °C)), acidic pH (∼5), and alkaline pH (∼11)) conditions, the fabricated large-scale carbon-based perovskite solar cells (C-LSPSCs) retained unexpected long-term stability in their performance for over 50 days. As to appraise the performance superiority of the fabricated C-LSPSC devices under various aforesaid testing conditions, a working model of a mini-fan has been practically powered and demonstrated.