Synthesis and properties of Fe3O4-activated carbon magnetic nanoparticles for removal of aniline from aqueous solution: equilibrium, kinetic and thermodynamic studies

Green-Synthesized Characterization, Antioxidant and Antibacterial Applications of CtAC/MNPs-Ag Nanocomposites

The emergence of antibiotic resistance, caused by the improper use of antibiotics, is a significant challenge in combating infectious diseases, leading to millions of annual fatalities. The occurrence of antimicrobial side effects catalyzes the investigation of novel antimicrobial compounds and sources of drugs. Consequently, the research on biological activity that is conducted on plants, plant extracts, and compounds that are produced from plant components is of utmost significance. In this study, CtAC/MNPs were obtained by the reaction of activated carbon (AC) obtained from the fruits of the Celtis tournefortii (Ct) plant and magnetic nanoparticles (MNPs), and a CtAC/MNPs-Ag nanocomposite was synthesized by the reduction in silver ions added to the reaction. The synthesized CtAC/MNPs and CtAC/MNPs-Ag nanocomposites were analyzed spectroscopically (FTIR, XRD), microscopically (SEM, EDX), optically (DLS), electrochemically (zeta potential) and magnetically (VSM). The antibacterial activities of CtAC/MNPs and CtAC/MNPs-Ag nanocomposites against S. aureus and E. coli were investigated by microdilution method using minimal inhibitory concentration (MIC) and disk diffusion methods. Antioxidant activity study, including total phenolic content and DPPH and cuprac assays, revealed the remarkable effect of the CtAC/MNPs-Ag nanocomposite. This study has the advantages of obtaining CtAC/MNPs and CtAC/MNPs-Ag nanocomposites in a short time without requiring energy, and most importantly, the reaction takes place without using any toxic substances. In addition, according to the data obtained in the study, the CtAC/MNPs-Ag nanocomposite is thought to shed light on biomedical research.

Synthesis and characterization of iron oxide-commercial activated carbon nanocomposite for removal of hexavalent chromium (Cr6+) ions and Mordant Violet 40 (MV40) dye

Iron Oxide-commercial activated carbon nanocomposite (CAC-IO) was prepared from commercial activated carbon (CAC) by the co-precipitation method, and the resulting nanocomposite was used as an adsorbent to remove hexavalent chromium (Cr6+) ions and Mordant Violet 40 (MV40) dye from wastewater. The produced materials (CAC, CAC after oxidation, and CAC-IO) were comparatively characterized using FTIR, BET, SEM, EDX TEM, VSM, and XRD techniques. The adsorption mechanism of Cr6+ ions and MV40 dye on CAC-IO was examined using Langmuir and Freundlich isotherm models.. Different models were applied to know the adsorption mechanism and it was obtained that Pseudo-second order fits the experimental data better. This means that the adsorption of the adsorbate on the nanocomposite was chemisorption. The maximum removal percent of Cr6+ ions by CAC-IO nanocomposite was 98.6% determined as 2 g L-1 adsorbent concentration, 100 mg L-1 initial pollutant concentration, solution pH = 1.6, the contact time was 3 h and the temperature was room temperature. The maximum removal percentage of Mordant Violet 40 dye (C.I. 14,745) from its solutions by CAC-IO nanocomposite was 99.92% in 100 mg L-1 of initial dye concentrations, 1.0 g L-1 of adsorbent concentration, solution pH = 2.07, the contact time was 3 h. The MV40 dye adsorption on CAC-IO was the most fitted to the Freundlich isotherm model. The maximum adsorption capacity was calculated according to the Langmuir model as 833.3 mg g-1 at 2 g L-1 of adsorbent concentration and 400 mg L-1 of initial MV40 dye concentration. The Cr6+ ions adsorption on CAC-IO was more fitted to the Freundlich model with Qmax, equal to 312.50 mg g-1 at 1 g L-1 adsorbent concentration and 400 mg L-1 of Cr6+ ions initial concentrations.

Efficient degradation and mineralization of aniline in aqueous solution by new dielectric barrier discharge non-thermal plasma

Aniline is a priority pollutant that is unfavorable to the environment and human health due to its carcinogenic and mutagenic nature. The performance of the dielectric barrier discharge reactor was examined based on the aniline degradation efficiency. Different parameters were studied and optimized to treat various wastewater conditions. Role of active species for aniline degradation was investigated by the addition of inhibitors and promoters. The optimum conditions were 20 mg/L initial concentration, 1.8 kV applied voltage, 4 L/min gas flow rate and a pH of 8.82. It was observed that 87% of aniline was degraded in 60 min of dielectric barrier discharge treatment at optimum conditions. UV-Vis spectra showed gradual increase in the treatment efficiency of aniline with the propagation of treatment time. Mineralization of AN was confirmed by TOC measurement and a decrease in pH during the process. To elicit the aniline degradation route, HPLC and LC-MS techniques were used to detect the intermediates and byproducts. It was identified that aniline degraded into different organic byproducts and was dissociated into carbon dioxide and water. Comparison of the current system with existing advanced oxidation processes showed that DBD has a remarkable potential for the elimination of organic pollutants.

Synthesis and application of lanthanum-doped magnetic biochar composite adsorbent for removal of fluoride from water

Fluoride levels greater than 1.5 mg/L in drinking water are a global environmental issue that can seriously harm the health of humans. One of the most effective techniques for defluoridating water is adsorption. The main drawbacks of many adsorbent materials include their poor adsorption capabilities, prolonged contact times, excessively low or high pH levels, and high dosages. The biochar-based magnetic nanocomposite adsorbent was synthesized in the current study and used as an adsorbent for water defluoridation. Through slow pyrolysis, coffee husk waste was converted to biochar. The composite was created by chemically co-precipitating iron and lanthanum oxide nanoparticles onto the surface of biochar. By using X-ray diffraction analysis (XRD), Fourier transform infrared spectrometry (FTIR), Brunauer-Emmett-Teller (BET), and pHPZC values, researchers were able to describe the magnetic biochar nanocomposite material. The Central Composite Design (CCD), which uses four input variables including dosage (2-5 g/L), solution pH (4-8), contact time (30-70 min), and initial concentration (10-20 mg/L), was used to design the experiments. The quadratic model indicated that the ideal conditions for removing 98.994% of the fluoride from water (adsorbent dosage of 5 g L-1, pH 5.74, contact period of 60 min, and initial concentration of 12.245 mg/L) would be attained. The average triplicate value in ideal circumstances produced a removal effectiveness of 98.51%, demonstrating the proposed response surface's capacity for prediction. The findings of this investigation showed that the magnetic biochar nanocomposite that was created is an effective fluoride adsorbent.

Systematic studies on the effect of structural modification of orange peel for remediation of phenol contaminated water

In the present study, orange peel biochar has been utilized as the adsorbent for the removal of phenol from contaminated water. The biochar was prepared by thermal activation process at three different temperature 300, 500 and 700°C and are defined as B300, B500, and B700 respectively. The synthesized biochar has been characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transformation infrared spectroscopy (FTIR), RAMAN spectroscopy, X-ray photoelectron spectroscopy (XPS), and UV-Vis spectroscopy. SEM analysis revealed a highly irregular and porous structure for B700 as compared with others. The parameters such as initial phenol concentration, pH, adsorption dosage, and contact time were optimized, and the maximum adsorption efficiency and capacity of about 99.2% and 31.0 mg/g was achieved for B700 for phenol adsorption. The Branauer-Emmett-Teller (BET) surface area and Berrate-Joyner-Halenda (BJH) pore diameter obtained for B700 were about 67.5 m² /g and 3.8 nm. The adsorption of phenol onto the biochar followed Langmuir isotherm showing linear fit with R²  = 0.99, indicating monolayer adsorption. The kinetic data for adsorption is best fitted for pseudo-second order. The thermodynamic parameters ΔG°, ΔH°, and ΔS° values obtained are negative, which means that the adsorption process is spontaneous and exothermic. The adsorption efficiency of phenol marginally declined from 99.2% to 50.12% after five consecutive reuse cycles. The study shows that the high-temperature activation increased the porosity and number of active sites over the orange peel biochar for efficient adsorption of phenol. PRACTITIONER POINTS: Orange peel is thermally activated at 300, 500, and 700°C for structure modification. Orange peel biochars were characterized for its structure, morphology, functional groups, and adsorption behavior. High-temperature activation improved the adsorption efficiency up to 99.21% due to high porosity.

Fabrication of glutathione functionalized self-assembled magnetite nanochains for effective removal of crystal violet and phenol red dye from aqueous matrix

A novel fabrication of magnetite (Fe₃O₄) nanochains, surface functionalized with glutathione (GSH), has been attempted through a basic wet reduction method, coalesced with oxidative etching for the removal of crystal violet (CV) and phenol red (PR) from an aqueous solution. The structural and functional characterizations of GSH@Fe₃O₄ MNPs were performed using SEM-EDX, DLS, XRD, and FTIR. The nanochain-structured adsorbent was found to have an average size of 24 ± 1.29 nm and a zeta potential value of - 6.44 mV. The batch experiments showed that GSH@Fe₃O₄ MNPs have a brilliant removal efficiency of 97% and 79% for CV and PR dyes, respectively, within a period of 60 min. The influence of different operational parameters like adsorbent dosage, pH, temperature, reaction time, and initial dye concentration on the removal behaviour of the adsorbent was studied in detail. The adsorbate-adsorbent reaction was tested over isotherm models, and the reaction fitted well for Langmuir isotherm with an excellent q_max value of 1619.5 mg/g and 1316.16 mg/g for CV and PR dye, respectively. The experimental results were also validated using different reaction kinetics, and it was found that the pseudo-first-order model fits well for PR dye adsorption (R² = 0.91), while adsorption of CV dye was in best agreement with the pseudo-second-order kinetic model (R² = 0.98). Thermodynamic studies revealed that the adsorption reaction was spontaneous and endothermic in nature. Furthermore, GSH@Fe₃O₄ MNPs can be reused effectively up to 5 cycles of dye removal. Major mechanisms involved in the adsorption reaction were expected to be electrostatic attraction, hydrogen bonding, and π-interactions. The efficiency of GSH@Fe₃O₄ MNPs in real water samples suggested that it has a high potential for dye removal from complex aqueous systems and could be used as an effective alternative for remediation of dyes contaminated water.

Adsorption of Anionic Dyes from Wastewater onto Magnetic Nanocomposite Powders Synthesized by Combustion Method

In the present study, new magnetic nanocomposites were successfully prepared by combustion method, characterized by X-ray diffraction, Fourier transform infrared spectroscopy, magnetic measurements, N2 adsorption–desorption thermal analysis, and scanning electron microscopy, and tested as adsorbents for the removal of anionic dyes (Acid Yellow 42 and Acid Red 213) from aqueous solutions. The influence of process variables solution pH, adsorbent dose, initial dye concentration and temperature on the adsorption was evaluated. The best kinetic model that fitted with experimental data was a pseudo-second order model, and the equilibrium data were correlated by Langmuir isotherm model for the investigated dyes. Maximum removal efficiencies of 98.54% and 97.58% was obtained for Acid Yellow 42 and Acid Red 213, respectively, indicating the superior adsorption capacity of the new synthesized magnetic nanocomposites. The thermodynamic parameters indicated the spontaneous and endothermic nature of the adsorption process.

Development of copper-iron bimetallic nanoparticle impregnated activated carbon derived from coconut husk and its efficacy as a novel adsorbent toward the removal of chromium (VI) from aqueous solution

The present work demonstrates the preparation of biodegradable coconut husk derived activated carbon (CAC) impregnated with bimetallic nanoparticles consisting of zerovalent iron and copper to produce a new adsorbent (Fe⁰ /Cu-CAC). The new adsorbent was further employed to determine the removal efficiency of Chromium (VI) from aqueous solutions. Chromium (VI) adsorption process by Fe⁰ /Cu-CAC was found to be favorable at pH ~ 3, attaining 95.28% removal efficiency while its counterpart CAC attained only ~41%. Negative ΔG⁰ value suggests that the process was thermodynamically spontaneous and ΔH⁰ was observed to be 8.496 kJ/mol, further corroborating the endothermic nature of the process. Pseudo-second order model was best suited to explain the kinetics of the process with R² value of 0.99683 and an error of 6.73%. Equilibrium parameter (R_L ) derived from Langmuir isotherm was calculated to be 0.1103, indicating favorable adsorption and thus Langmuir isotherm can be used to describe the process of adsorption of Cr (VI) by Fe⁰ /Cu-CAC. Finally, a maximum monolayer adsorption capacity of 173.9 mg/g indicated the suitability of the prepared adsorbent in treating chromium contaminated wastewater streams. PRACTITIONER POINTS: Facile development of novel adsorbent from biodegradable coconut husk via cost effective route. Utilization of the adsorbent towards removal of toxic pollutant like Cr (VI) from its aqueous solution. Validation of the effective adsorption mechanism by Kinetic and Thermodynamic study.

Cytotoxic aquatic pollutants and their removal by nanocomposite-based sorbents

Water is an extremely essential compound for human life and, hence, accessing drinking water is very important all over the world. Nowadays, due to the urbanization and industrialization, several noxious pollutants are discharged into water. Water pollution by various cytotoxic contaminants, e.g. heavy metal ions, drugs, pesticides, dyes, residues a drastic public health issue for human beings; hence, this topic has been receiving much attention for the specific approaches and technologies to remove hazardous contaminants from water and wastewater. In the current review, the cytotoxicity of different sorts of aquatic pollutants for mammalian is presented. In addition, we will overview the recent advances in various nanocomposite-based adsorbents and different approaches of pollutants removal from water/wastewater with several examples to provide a backdrop for future research.

Batch Adsorption and Column Leaching Studies of Aniline in Chinese Loess Under Different Hydrochemical Conditions

Through batch adsorption and column leaching experiments, this study aimed to investigate the adsorption and transport behavior of aniline in loess and related mechanism under different hydrochemical conditions. Batch experiments results indicated that aniline adsorption reached equilibrium after about 120 min, and the adsorption fitted the pseudo-second-order kinetic and Freundlich models well. The adsorption was spontaneous and exothermic process, indicating the aniline adsorbed by inherent colloidal particles (ICPs) tended to transport. Low pH value, ionic strength and temperature benefitted the adsorption. Column experiments results under different ionic strengths (100, 10 and 1 mM) confirmed the potential transport of aniline. The FT-IR spectra have further suggested that aniline was adsorbed by the ICPs through hydrogen-bond, hydrophobic effect and cation exchange interactions. Low ionic strength was advantageous for the adsorption of aniline in loess and the stabilities of ICPs in solution, but enhanced the co-transport probability of ICPs with aniline in loess.

Environmentally friendly synthesis of Fe2O3@SiO2 nanocomposite: characterization and application as an adsorbent to aniline removal from aqueous solution

Silica-based nanocomposite syntheses employ many harmful substances, which, in turn, demand the development of new synthetic environmental-friendly routes that meet the principles of green chemistry. In this work, we present a novel magnetic adsorbent, Fe₂O₃@SiO₂ nanocomposite (Fe@SiNp), successfully obtained without surfactant, employing an electrochemical method. We characterized the nanocomposite and then applied it to remove aniline from the water medium. Characterization was carried out by vibrating-sample magnetometry (VSM), X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FT-IR). The parameters to the adsorptive removal of aniline were successfully optimized, which made possible to remove 71.04 ± 0.06% (126.6 ± 2.0 mg/g) from a 100 mg/L aniline solution at pH 6 and 323 K, by employing around 50 mg of Fe@SiNp, at a contact time of 40 min. The adsorption of aniline by Fe@SiNp is a spontaneous and exothermic process according to the pseudo-second-order kinetic model (r² = 1 at 20 mg/L aniline concentration) and the Freundlich isotherm model (r² = 0.9986).

Anionic azo dyes removal from water using amine-functionalized cobalt–iron oxide nanoparticles: a comparative time-dependent study and structural optimization towards the removal mechanism

Efficient and selective removal of azo dyes from water by amine-functionalized-CoFe₂O₄ nanoparticles reliant on structural features such as size, charge, hydrophobicity/hydrophilicity, and S/C atoms.

Activated Carbon from Yam Peels Modified with Fe3O4 for Removal of 2,4-Dichlorophenoxyacetic Acid in Aqueous Solution

The removal of organic pollutants from water sources can be enhanced using suitable adsorbents. The aim of this research was to study the adsorption capacity and potential reuse of a magnetic adsorbent prepared from agricultural wastes of yam peels (Dioscorea rotundata) for 2,4-dichlorophenoxyacetic (2,4-D) acid removal. The procedure was performed through carbonization and activation at 400 and 500 °C, respectively. Then, the as-prepared activated carbon (AC) was chemically modified using magnetite (Fe3O4) nanoparticles. The AC and magnetic activated carbon (MAC) were characterized and then used for batch adsorption and regeneration tests at different pH, initial concentrations of 2,4-D, and temperature. AC and MAC were showed to have microporous structures with surface areas of 715 and 325 m2/g, respectively. Superparamagnetic behavior was observed for MAC with a saturation magnetization of 6 emu/g. The results from the batch experiments showed higher adsorption capacity at high initial concentration of 2,4-D, low pH, and room temperature. The thermodynamic parameters indicated that the experiments proceeded as exothermic and spontaneous adsorption. Our findings also showed that MAC can be separated from the water medium through a facile magnetic procedure, and from regeneration experiments, MAC showed better results with 60% of its initial adsorption capacity after five cycles. Hence, MAC was found to be a promising alternative adsorbent of pesticides in water.

Atenolol adsorption onto multi-walled carbon nanotubes modified by NaOCl and ultrasonic treatment; kinetic, isotherm, thermodynamic, and artificial neural network modeling

The removal of pharmaceutical pollutants from the aqueous environment is a great environmental concern, mainly due to their diversity, high consumption, and sustainability. In the current study, we aimed to investigate the ability of multi-walled carbon nanotubes (MWCNTs) modified by sodium hypochlorite (NaOCl) and ultrasonic treatment in refining wastewaters contaminated with Atenolol β-blocker drug (ATN). The physical and structural characteristics of the raw MWCNTs and modified MWCNTs (M-MWCNTs) were analyzed using SEM, TEM, Raman spectroscopy, TGA, and FT-IR techniques. The effects of different parameters, including pH, initial concentration, contact time, and temperature were studied and optimized. Subsequently, the adsorption data were analyzed by several kinetic and equilibrium isotherm equations and modeled by artificial neural network (ANN). Highest ATN removal (87.89%) ((q_e,exp = 46.03 mg g^-1)) occurred on the adsorbent activated within 10 s of ultrasonication time and NaOCl 30%. Moreover, adsorbent modification significantly improved the ATN removal, so that the removal rate on the raw MWCNTs was about 58%, but in the same conditions, M-MWCNTs removed more than 92% of the adsorbate. The adsorption process reached equilibrium after 90 min under the optimized pH of 6. According to ANN modeling, approximately the whole values dispersed around the 45°line, indicating a good compatibility between the trial results and ANN-predicted data. The modification of MWCNTs in proper ultrasonic power via appropriate concentration of NaOCl solution removed many of the impurities and significantly improved the adsorption performance of MWCNTs.

Development of magnetic porous coordination polymer adsorbent for the removal and preconcentration of Pb(II) from environmental water samples

A novel porous coordination polymer adsorbent (BTCA-P-Cu-CP) based on a piperazine(P) as a ligand and 1,2,4,5-benzenetetracarboxylic acid (BTCA) as a linker was synthesized and magnetized to form magnetic porous coordination polymer (BTCA-P-Cu-MCP). Fourier transform infrared (FTIR), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), field emission scanning electron microscope(FESEM), energy-dispersive X-ray spectroscopy(EDS), CHN, and Brunauer-Emmett-Teller(BET) analysis were used to characterize the synthesized adsorbent. BTCA-P-Cu-MCP was used for removal and preconcentration of Pb(II) ions from environmental water samples prior to flame atomic absorption spectrometry(FAAS) analysis. The maximum adsorption capacity of BTCA-P-Cu-MCP was 582 mg g^-1. Adsorption isotherm, kinetic, and thermodynamic parameters were investigated for Pb(II) ions adsorption. Magnetic solid phase extraction (MSPE) method was used for preconcentration of Pb(II) ions and the parameters influencing the preconcentration process have been examined. The linearity range of proposed method was 0.1-100 μg L^-1 with a preconcentration factor of 100. The limits of detection and limits of quantification for lead were 0.03 μg L^-1 and 0.11 μg L^-1, respectively. The intra-day (n = 7) and inter-day (n = 3) relative standard deviations (RSDs) were 1.54 and 3.43% respectively. The recoveries from 94.75 ± 4 to 100.93 ± 1.9% were obtained for rapid extraction of trace levels of Pb(II) ions in different water samples. The results showed that the BTCA-P-Cu-MCP was steady and effective adsorbent for the decontamination and preconcentration of lead ions from the aqueous environment.

In Situ Synthesis of a Stable Fe₃O₄@Cellulose Nanocomposite for Efficient Catalytic Degradation of Methylene Blue

To rapidly obtain a stable Fe₃O₄@cellulose heterogeneous Fenton catalyst, a novel in situ chemical co-precipitation method was developed. Compared with mechanical activation (MA)-pretreated cellulose (MAC), MA + FeCl₃ (MAFC)-pretreated cellulose (MAFCC) was more easily dissolved and uniformly distributed in NaOH/urea solvent. MAFCC and MAC solutions were used as precipitators to prepare Fe₃O₄@MAFCC and Fe₃O₄@MAC nanocomposites, respectively. MAFCC showed stronger interaction and more uniform combination with Fe₃O₄ nanoparticles than MAC, implying that MAFC pretreatment enhanced the accessibility, reactivity, and dissolving capacity of cellulose thus, provided reactive sites for the in situ growth of Fe₃O₄ nanoparticles on the regenerated cellulose. Additionally, the catalytic performance of Fe₃O₄@MAFCC nanocomposite was evaluated by using for catalytic degradation of methylene blue (MB), and Fe₃O₄@MAC nanocomposite and Fe₃O₄ nanoparticles were used for comparative studies. Fe₃O₄@MAFCC nanocomposite exhibited superior catalytic activity for the degradation and mineralization of MB in practical applications. After ten cycles, the structure of Fe₃O₄@MAFCC nanocomposite was not significantly changed owing to the strong interaction between MAFCC and Fe₃O₄ nanoparticles. This study provides a green pathway to the fabrication of a stable nanocomposite catalyst with high catalytic performance and reusability for the degradation of organic pollutants.

Smart Materials for Environmental Remediation Based on Two-Component Gels: Room-Temperature-Phase-Selective Gelation for the Removal of Organic Pollutants Including Nitrobenzene/O-Dichlorobenzene, and Dye Molecules from the Wastewater

Novel two-component gel systems based on aliphatic acid-hydroxy/base interaction were developed as smart materials for environmental remediation. The G1-A16 gelator could be used directly as a powder form to selectively gel aromatic solvents (nitrobenzene and o-dichlorobenzene) from their mixtures with wastewater (containing 0.5 M sodium nitrate and 0.5 M sodium sulfate) via a simple shaking strategy at room temperature without employing co-solvents and a heating-cooling process. Meanwhile, the two-component gel system can efficiently remove the toxic dyes from the aqueous solution. The dominant factors that drive gelation in the case of the gelator and nitrobenzene or water have been studied using FT-IR, 1H NMR, and XRD. Overall, our research provides an efficient two-component approach for facilely tuning the properties of one-component gel for the realization of high-performance functionalities of gels. At the same time, our study demonstrates potential industrial application prospect in removing pollutants efficiently (such as aromatic solvents and toxic dye removal).

Convenient pH-responsive removal of Acid Black 1 by green l-histidine/iron oxide magnetic nanoadsorbent from water: performance and mechanistic studies

This study was aimed at developing green histidine-modified Fe3O4 nanoparticles (His-MNPs) for the adsorptive removal of Acid Black 1 (AB1) from aqueous solution. The His-MNPs were characterized by atomic force microscopy, scanning electron microscopy-energy dispersive X-ray spectrometry, infra-red spectra and thermogravimetry. These MNPs were spherical (average diameter 11-28 nm) with polydispersity index of 1.40 and about 13% mass coating of histidine. To optimize AB1 adsorption on His-MNPs and understand its mechanism, the influences of different operational variables (pH, adsorbent amount, temperature, initial AB1 concentration, contact time, ionic strength, etc.) on adsorption were examined with adsorption isotherms, kinetics and thermodynamic studies. The AB1 adsorption from water was fast with equilibrium time ≤ 45 min. The adsorption equilibrium was best fitted to the Langmuir isotherm model (q max = 166.7 mg g-1 at the adsorbent dose of 0.2 g L-1, temperature 30 °C and pH 4). The linearity order for other isotherms was as follows: Dubinin-Radushkevich (D-R) < Temkin < Freundlich. The kinetics of the AB1 adsorption demonstrated the best compliance with the pseudo-second-order model, predominantly controlled by film diffusion as compared to intraparticle diffusion. Thermodynamic parameters (ΔH° and ΔG°) reflected the exothermic and spontaneous adsorption process. The values of ΔG°, ΔH°, activation energy and D-R free adsorption energy were all consistent with the physisorptive removal of AB1. The spectral (electronic and IR) and pH studies further corroborated the mechanism of AB1 removal by His-MNPs. The His-MNPs showed efficient adsorption, easy regeneration and excellent reusability, assisted by their pH-responsive properties. The prepared adsorbent can provide a safe, effective and economical alternative strategy for removing azo dyes from wastewater.

Highly Efficient and Reusable Montmorillonite/Fe₃O₄/Humic Acid Nanocomposites for Simultaneous Removal of Cr(VI) and Aniline

Recyclable nanomaterials are in great need to develop clean technology for applications in the removal of water contaminants. In this work, easily separable montmorillonite/Fe₃O₄/humic acid (MFH) nanocomposites were fabricated through a facile hydrothermal route. It was found the adsorption ability and stability of MFH was significantly enhanced due to the synergistic effects between montmorillonite, Fe₃O₄ nanoparticles and humic acid. The MFH nanocomposites are highly efficient and recyclable as they can remove at least 82.3% of Cr(VI) and 95.1% of aniline in six consecutive runs. The adsorption mechanism was investigated by analyzing the kinetic parameters of pseudo first-order, pseudo second-order, and intraparticle diffusion models and describing the equilibrium isotherms of Langmuir and Freundlich models. Results indicated different adsorption mechanisms of Cr(VI) and aniline by MFH. The readily synthesized MFH nanocomposites can act as effective and practical materials for environmental applications.

Silica-coated magnetite nanoparticles core-shell spheres (Fe3O4@SiO2) for natural organic matter removal

Background

In this work, the magnetite (Fe₃O₄) nanoparticles (MNPs) and silica-coated magnetite nanoparticles (SMNPs) were synthesized as adsorbents for removing humic acid (HA) from water resources.

Methods

The adsorption processes were performed in batch experiments with which the influence of pH, reaction time, adsorbent dosage, initial concentrations of HA and temperature were investigated. Specific techniques were applied to characterize the features of both adsorbents (i. e. TECHNIQUES) (SEM, XRD, TEM, BET, EDX and VSM).

Results

The maximum saturation magnetization for SMNPs was 30.2 emu/g, which made its separation from the solution by a magnetic field to be easier and faster. The HA adsorption process onto the both adsorbents were best described by the Freundlich isotherm and pseudo-second-order kinetic models. Highest adsorption efficiency of HA by MNPs an d SMNPs occurred at acidic conditions (pH ≈ 3). The mechanisms of adsorption process involved with a physisorption process such as (i. e. hydrogen bonding and electrostatic interaction). The predicted maximum monolayer adsorption capacities obtained by Langmuir isotherm model for MNPs and SMNPs were 96.15 and 196.07 mg/g, respectively.

Conclusion

Higher amount of HA adsorption onto the surfaces of SMNPs than MNPs surfaces was observed, reflecting that silica impregnated on MNPs enhances the efficiency of the adsorbent in removing HA.

Electronic supplementary material

The online version of this article (doi:10.1186/s40201-016-0262-y) contains supplementary material, which is available to authorized users.

Modification of a magnetic carbon composite for ciprofloxacin adsorption

A magnetic carbon composite, Fe₃O₄/C composite, was fabricated by one-step hydrothermal synthesis, modified by heat treatment under an inert atmosphere (N₂), and then used as an adsorbent for ciprofloxacin (CIP) removal. Conditions for the modification were optimized according to the rate of CIP removal. The adsorbent was characterized by Fourier transform infrared spectroscopy, X-ray diffraction measurements, vibrating-sample magnetometry, scanning electron microscopy, transmission electron microscopy, and N₂ adsorption/desorption isotherm measurements. The results indicate that the modified adsorbent has substantial magnetism and has a large specific area, which favor CIP adsorption. The effects of solution pH, adsorbent dose, contact time, initial CIP concentration, ion strength, humic acid and solution temperature on CIP removal were also studied. Our results show that all of the above factors influence CIP removal. The Langmuir adsorption isotherm fits the adsorption process well, with the pseudo second-order model describing the adsorption kinetics accurately. The thermodynamic parameters indicate that adsorption is mainly physical adsorption. Recycling experiments revealed that the behavior of adsorbent is maintained after recycling for five times. Overall, the modified magnetic carbon composite is an efficient adsorbent for wastewater treatment.

Heterogeneous Fenton-like oxidation of petrochemical wastewater using a magnetically separable catalyst (MNPs@C): process optimization, reaction kinetics and degradation mechanisms

MNPs@C magnetic composite was synthesized and applied as a heterogeneous catalyst in the Fenton oxidation for PCW treatment. The organic compounds were degraded by the ˙OH radicals released from decomposition of H₂O₂ in the presence of MNPs@C.

Cadmium removal from aqueous solution by green synthesis iron oxide nanoparticles with tangerine peel extract

Background

The adsorption process by metal oxide nanoparticles has been investigated an effective agent for removing organic and inorganic contaminants from water and wastewater. In this study, iron oxide nanoparticles were synthesized in the presence of tangerine peel extract as adsorbent for cadmium ions removal from contaminated solution. Iron oxide nanoparticles prepared by co-precipitation method and tangerine peel extract was used to prevent accumulation and reduce the diameter of the particles. Effect of various parameters such as contact time, pH, metal concentration and adsorbent dosage was determined on the removal efficiency.

Results

The different concentrations of tangerine peel had an impact on the size of nanoparticles. As, increasing the concentration of tangerine peel extract from 2 to 6 % the average size of synthesized iron oxide nanoparticles decreased 200 nm to 50 nm. The maximum removal of cadmium ions (90 %) occurred at pH of 4 and adsorbent dose of 0.4 g/100 ml. Adsorption of cadmium ions by synthesized iron oxide nanoparticles followed Freundlich adsorption model and pseudo-second-order equation.

Conclusion

The cadmium ions are usually soluble in acidic pH and the maximum removal of cadmium by green synthesis iron oxide nanoparticles was obtained in the pH of 4, so these nanoparticles can be a good adsorbent for the removal of cadmium from wastewater.

High-capacity adsorption of aniline using surface modification of lignocellulose-biomass jute fibers

Pyromellitic dianhydride (PMDA) modified jute fiber (MJF) were prepared with microwave treatment to generate a biosorbent for aniline removal. The characterization of the biosorbent was investigated by SEM, BET and FT-IR analysis to discuss the adsorption mechanism. The studies of various factors influencing the adsorption behavior indicated that the optimum dosage for aniline adsorption was 3g/L, the maximum adsorption capacity was observed at pH 7.0 and the adsorption process is spontaneous and endothermic. The aniline adsorption follows the pseudo second order kinetic model and Langmuir isotherm model. Moreover, the biosorbent could be regenerated through the desorption of aniline by using 0.5M HCl solution, and the adsorption capacity after regeneration is even higher than that of virgin MJF. All these results prove MJF is a promising adsorbent for aniline removal in wastewater.

Magnetite impregnation effects on the sorbent properties of activated carbons and biochars

This paper discusses the sorbent properties of magnetic activated carbons and biochars produced by wet impregnation with iron oxides. The sorbents had magnetic susceptibilities consistent with theoretical predictions for carbon-magnetite composites. The high BET surface areas of the activated carbons were preserved in the synthesis, and enhanced for one low surface area biochar by dissolving carbonates. Magnetization decreased the point of zero charge. Organic compound sorption correlated strongly with BET surface areas for the pristine and magnetized materials, while metal cation sorption did not show such a correlation. Strong sorption of the hydrophobic organic contaminant phenanthrene to the activated carbon or biochar surfaces was maintained following magnetite impregnation, while phenol sorption was diminished, probably due to enhanced carbon oxidation. Copper, zinc and lead sorption to the activated carbons and biochars was unchanged or slightly enhanced by the magnetization, and iron oxides also contributed to the composite metal sorption capacity. While a magnetic biochar with 219 ± 3.7 m(2)/g surface area nearly reached the very strong organic pollutant binding capacity of the two magnetic activated carbons, a magnetic biochar with 68 ± 2.8 m(2)/g surface area was the best metal sorbent. Magnetic biochars thus hold promise as more sustainable alternatives to coal-derived magnetic activated carbons.

Performance and characteristics of fluoride adsorption using nanomagnetite graphite–La adsorbent

Nanomagnetite graphite–La was a promising adsorbent for effective F⁻ removal with high adsorption capacity and stable reuse ability.

Powder activated carbon/Fe3O4 hybrid composite as a highly efficient heterogeneous catalyst for Fenton oxidation of tetracycline: degradation mechanism and kinetic

In this work, we prepared and used a composite of powder activate carbon/Fe₃O₄ magnetic nanoparticles (PAC/Fe₃O₄ MNPs) as a heterogeneous catalyst to remove tetracycline (TC) from aqueous solution.

Enhanced chromium (VI) removal using activated carbon modified by zero valent iron and silver bimetallic nanoparticles

Recently, adsorption process has been introduced as a favorable and effective technique for the removal of metal ions from aqueous solutions. In the present study, bimetallic nanoparticles consisting of zero valent iron and silver were loaded on the activated carbon powder for the preparation of a new adsorbent (PAC-Fe^o/Ag). The above adsorbent was characterized by using XRD, SEM and TEM techniqes. Experimental data were exploited for kinetic, equilibrium and thermodynamic evaluations related to the adsorption processes. The Cr(VI) adsorption process was found to be favorable at pH 3 and it reached equilibrium state within 60 min. The stirring rate did not have a significant effect on the adsorption efficiency. Furthermore, the monolayer adsorption capacity of Cr(VI) based on the Langmuir model was measured to be 100 mg/g. The experimental equilibrium data were fitted to the Freundlich adsorption and pseudo second-order models. According to the thermodynamic study, the adsorption process was spontaneous and endothermic in nature, indicating the adsorption capacity increases with increasing the temperature. The results also revealed that the synthesized composite can be potentially applied as a magnetic adsorbent to remove Cr(VI) contaminants from aqueous solutions.

Magnetic heterogeneous catalytic ozonation: a new removal method for phenol in industrial wastewater

In this study, a new strategy in catalytic ozonation removal method for degradation of phenol from industrial wastewater was investigated. Magnetic carbon nano composite as a novel catalyst was synthesized, characterized and then used in the catalytic ozonation process (COP) and compared with the single ozonation process (SOP). The influential parameters were all investigated. The results showed that the removal efficiency of phenol and COD (chemical oxygen demand) in COP (98.5%, 69.8%) was higher than those of SOP (78.7%, 50.5%) and the highest catalytic potential was achieved at optimal neutral pH. First order modeling demonstrated that the reactions were dependent on the concentration of catalyst, with kinetic constants varying from 0.023 1/min (catalyst = 0 g/L) to 0.071 1/min (catalyst = 4 g/L), whereby the optimum dosage of catalyst was found to be 2 g/L. Furthermore, the catalytic properties of the catalyst remained almost unchanged after 5-time reuse. The results regarding the biodegradability of the effluent showed that a 5-min reaction time in COP reduced the concentrations of phenol and COD to the acceptable levels for the efficient post-treatment in the SBR in a 4-h cycle period. Finally, this combined system is proven to be a technically effective method for treating phenolic contaminants.

Covalently modified magnetite nanoparticles with PEG: preparation and characterization as nano-adsorbent for removal of lead from wastewater

BACKGROUND

Lead is one of the hazardous materials which is associated with pollution and toxicity problems. This paper describes a novel approach for removal of lead from wastewater. Although naked magnetic nanoparticles have been applied for removal of different pollutants from wastewater, there was no research on employment of covalently PEG modified magnetic nanoparticles for such purpose.

RESULTS

A magnetic nano-adsorbent was prepared by chemically modification of magnetite nanoparticles (MNPs) with polyethylene glycol (PEG) for removal of lead ions. The surface of MNPs was coated covalently with 3-aminopropyltriethoxysilane (APTES) and PEG. Modified MNPs (MNPs-APTES-PEG) were characterized by FT-IR, XRD, SEM, and particle size analysis. Compared to the oleic acid coated MNPs, MNPs-APTES-PEG exhibited significant higher uptake capability for Pb(II) ions. The effective parameters on the extent of adsorption (time, temperature, Pb(II) concentration, contact time and pH) were studied and optimized by response surface methodology. Maximum uptake of MNPs-APTES-PEG for Pb(II) was determined to be 81.39 ± 2.5%. The results showed that the kinetic data was best described by Pseudo-second order model as evidenced by the relatively high value of determination coefficient (R(2) = 0.9998). Successful removal of Pb(II) from industrial wastewater was also accomplished by MNPs-APTES-PEG.

CONCLUSIONS

The results revealed high capability and excellent efficiency of developed nano-adsorbents in removal of lead contaminants from industrial wastewater.