Performance of NiO doped on alkaline sludge from waste photovoltaic industries for catalytic dry reforming of methane

Alkali sludge (AS) is waste abundantly generated from solar photovoltaic (PV) solar cell industries. Since this potential basic material is still underutilized, a combination with NiO catalyst might greatly influence coke resentence, especially in high-temperature thermochemical reactions (Arora and Prasad, RSC Adv. 6:108,668-108688, 2016). This paper investigated alkaline sludge containing 3CaO-2SiO2 doped with well-known NiO to enhance the dry reforming of methane (DRM) reaction. The wet-impregnation method was used to prepare the xNiO/AS (x = 5-15%) catalysts. Subsequently, all catalysts were tested by using X-ray diffraction (XRD), nitrogen adsorption/desorption (BET), temperature-programmed reduction of hydrogen (H2-TPR), temperature-programmed desorption of carbon dioxide (TPD-CO2), field emission scanning electron microscopy (FESEM-EDX), and X-ray photoelectron spectroscopy (XPS). The spent catalysts were analyzed by thermogravimetric analysis (TGA/DTG), transmission electron microscopy (TEM), and temperature-programmed oxidation (TPO). The catalytic performance of xNiO/AS catalysts was investigated in a fixed bed reactor connected with gas chromatography thermal conductivity detector (GC-TCD) at a CH4:CO2 flow rate of 30 mL-1 during a 10-h reaction by following (Shamsuddin et al., Int. J. Energy Res. 45:15,463-15,480, 2021d). For optimization parameters, the effects of NiO concentration (5, 10, and 15%), reaction temperature (700, 750, 800, 850, and 900 °C), catalyst loading (0.1, 0.2, 0.3, 0.4, and 0.5 g), and gas hourly space velocity (GHSV) range from 3000, 6000, 9000, 12,000, and 15,000 h-1 were evaluated. The results showed that physical characteristics such as BET surface area and porosity do not significantly impact NiO percentages of dispersion, whereas chemical characteristics like reducibility are crucial for the catalysts' efficient catalytic activity. Due to the active sites on the catalyst surface being more accessible, increased NiO dispersion resulted in higher reactant conversion. The catalytic performance on various parameters that showed 15%NiO/AS exhibited high reactant conversion up to 98% and 40-60% product selectivity in 700 °C, 0.2 g catalyst loading, and 12,000 h-1 GHSV. According to spent catalyst analyses, the catalyst was stable even after the DRM reaction. Meanwhile, increased reducibility resulted in more and better active site formation on the catalyst. Synergetic effect of efficient NiO as active metal and medium basic sites from AS enhanced DRM catalytic activity and stability with low coke formation.

Mineralization of palm oil mill effluent by advanced oxidation processes: A review on current trends and the way forward

Palm oil mill effluent (POME) is regarded as deleterious to the environment, primarily owing to the substantial volume of waste it produces during palm oil extraction. In terms of contaminant composition, POME surpasses the pollutant content typically found in standard municipal sewage, therefore releasing it without treatment into water bodies would do irreparable damage to the environment. Main palm oil mills are normally located in the proximity of natural rivers in order to take advantage of the cheap and abundant water source. The same rivers are also used as a water source for many villages situated along the river banks. As such, it is imperative to degrade POME before its disposal into the water bodies for obvious reasons. The treatment methods used so far include the biological processes such as open ponding/land application, which consist of aerobic as well as anaerobic ponds, physicochemical treatment including membrane technology, adsorption and coagulation are successful for the mitigation of contaminants. As the above methods require large working area and it takes more time for contaminant degradation, and in consideration of the strict environmental policies as well as palm oil being the most sort of vegetable oil in several countries, numerous researchers have concentrated on the emerging technologies such as advanced oxidation processes (AOPs) to remediate POME. Methods such as the photocatalysis, Fenton process, sonocatalysis, sonophotocatalysis, ozonation have attained special importance for the degradation of POME because of their efficiency in complete mineralization of organic pollutants in situ. This review outlines the AOP technologies currently available for the mineralization of POME with importance given to sonophotocatalysis and ozonation as these treatment process removes the need to transfer the pollutant while possibly degrading the organic matter sufficiently to be used in other industry like fertilizer manufacturing.

Catalytic, Theoretical, and Biological Investigations of Ternary Metal (II) Complexes Derived from L-Valine-Based Schiff Bases and Heterocyclic Bases

A new series of ternary metal complexes, including Co(II), Ni(II), Cu(II), and Zn(II), were synthesized and characterized by elemental analysis and diverse spectroscopic methods. The complexes were synthesized from respective metal salts with Schiff’s-base-containing amino acids, salicylaldehyde derivatives, and heterocyclic bases. The amino acids containing Schiff bases showed promising pharmacological properties upon complexation. Based on satisfactory elemental analyses and various spectroscopic techniques, these complexes revealed a distorted, square pyramidal geometry around metal ions. The molecular structures of the complexes were optimized by DFT calculations. Quantum calculations were performed with the density functional method for which the LACVP++ basis set was used to find the optimized molecular structure of the complexes. The metal complexes were subjected to an electrochemical investigation to determine the redox behavior and oxidation state of the metal ions. Furthermore, all complexes were utilized for catalytic assets of a multi-component Mannich reaction for the preparation of -amino carbonyl derivatives. The synthesized complexes were tested to determine their antibacterial activity against E. coli, K. pneumoniae, and S. aureus bacteria. To evaluate the cytotoxic effects of the Cu(II) complexes, lung cancer (A549), cervical cancer (HeLa), and breast cancer (MCF-7) cells compared to normal cells, cell lines such as human dermal fibroblasts (HDF) were used. Further, the docking study parameters were supported, for which it was observed that the metal complexes could be effective in anticancer applications.

Catalytic response and molecular simulation studies in the development of synthetic routes in trimeric triaryl pyridinium type ionic liquids

Under conventional and silica-supported Muffle furnace methods, water-soluble substituted trimeric triaryl pyridinium cations with various inorganic counter anions are synthesized. The solvent-free synthesis method is superior to the conventional method in terms of non-toxicity, quicker reaction times, ease of workup, and higher yields. Trimeric substituted pyridinium salts acted as excellent catalytic responses for the preparation of Gem-bisamide derivatives compared with available literature. To evaluate the molecular docking, benzyl/4-nitrobenzyl substituted triaryl pyridinium salt compounds with VEGFR-2 kinase were used with H-bonds, π-π stacking, salt bridges, and hydrophobic contacts. The results showed that the VEGFR-2 kinase protein had the most potent inhibitory activity. Intriguingly, the compound [NBTAPy]PF₆^- had a strongly binds to VEGFR-2 kinase and controlled its activity in cancer treatment and prevention.

Environment-friendly deoxygenation of non-edible Ceiba oil to liquid hydrocarbon biofuel: process parameters and optimization study

Non-edible Ceiba oil has the potential to be a sustainable biofuel resource in tropical countries that can replace a portion of today's fossil fuels. Catalytic deoxygenation of the Ceiba oil (high O/C ratio) was conducted to produce hydrocarbon biofuel (high H/C ratio) over NiO-CaO₅/SiO₂-Al₂O₃ catalyst with aims of high diesel selectivity and catalyst reusability. In the present study, response surface methodology (RSM) technique with Box-Behnken experimental designs (BBD) was used to evaluate and optimize liquid hydrocarbon yield by considering the following deoxygenation parameters: catalyst loading (1-9 wt. %), reaction temperature (300-380 °C) and reaction time (30-180 min). According to the RSM results, the maximum yield for liquid hydrocarbon n-(C₈-C₂₀) was found to be 77% at 340 °C within 105 min and 5 wt. % catalyst loading. In addition, the deoxygenation model showed that the catalyst loading-reaction time interaction has a major impact on the deoxygenation activity. Based on the product analysis, oxygenated species from Ceiba oil were successfully removed in the form of CO₂/CO via decarboxylation/decarbonylation (deCOx) pathways. The NiO-CaO₅/SiO₂-Al₂O₃ catalyst rendered stable reusability for five consecutive runs with liquid hydrocarbon yield within the range of 66-75% with n-(C₁₅ + C₁₇) selectivity of 64-72%. Despite this, coke deposition was observed after several times of catalyst usage, which is due to the high deoxygenation temperature (> 300 °C) that resulted in unfavourable polymerization side reaction.

Effect of Different Metal Modified Dolomite Catalysts on Catalytic Glycerol Hydrogenolysis towards 1,2-Propanediol

A series of metal modified dolomite catalysts (10%Ni-20%Cu/Dol, 10%Co-20%Cu/Dol, 10%Fe-20%Cu/Dol, 10%Zn-20%Cu/DolNi) were synthesized via method of impregnation, later calcined at 500 ℃ and reduced by 5%H2 at 600 ℃. Those catalysts were formerly tested for their physico-chemical properties by BET, BJH, XRD, H2-TPR, NH3–TPD, CO2-TPD and SEM, and followed by evaluation in catalytic performance of glycerol hydrogenolysis to 1,2-propanediol (1,2-PDO). Among the examined catalysts, 10%Ni-20%Cu/Dol showed optimum hydrogenolysis activity owing to the good copper-nickel-dolomite interaction. The outcomes from the characterizations disclosed that the presence of nickel-copper species which principally enriched on dolomite surface thereby enhanced the properties of the catalyst in terms of good metal reducibility along with the presence of adequate catalyst acidity. All the good features of 10%Ni-20%Cu/Dolcatalyst added to its high activity with 83.5% glycerol conversion (GC) and 75% 1,2-PDO with low methanol as side reaction product under 200 ℃, 4 MPa H2 and 10 h duration test, 1 g catalyst dosage and 20 wt% glycerol concentration.

Catalytic ketonization of palmitic acid over a series of transition metal oxides supported on zirconia oxide-based catalysts

Modification of a ZrO₂ based catalyst with selected transition metals dopants has shown promising improvement in the catalytic activity of palmitic acid ketonization. Small amounts of metal oxide deposition on the surface of the ZrO₂ catalyst enhances the yield of palmitone (16-hentriacontanone) as the major product with pentadecane as the largest side product. This investigation explores the effects of addition of carefully chosen metal oxides (Fe₂O₃, NiO, MnO₂, CeO₂, CuO, CoO, Cr₂O₃, La₂O₃ and ZnO) as dopants on bulk ZrO₂. The catalysts are prepared via a deposition–precipitation method followed by calcination at 550 °C and characterized by XRD, BET-surface area, TPD-CO₂, TPD-NH₃, FESEM, TEM and XPS. The screening of synthesized catalysts was carried out with 5% catalyst loading onto 15 g of pristine palmitic acid and the reaction carried out at 340 °C for 3 h. Preliminary studies show catalytic activity improvement with addition of dopants in the order of La₂O₃/ZrO₂ < CoO/ZrO₂ < MnO₂/ZrO₂ with the highest palmitic acid conversion of 92% and palmitone yield of 27.7% achieved using 5% MnO₂/ZrO₂ catalyst. Besides, NiO/ZrO₂ exhibits high selectivity exclusively for pentadecane compared to other catalysts with maximum yield of 24.9% and conversion of 64.9% is observed. Therefore, the changes in physicochemical properties of the dopant added ZrO₂ catalysts and their influence in palmitic acid ketonization reaction is discussed in detail.

Catalyst screening and optimization of a series of ZrO₂ supported metal oxides for ketonization of undiluted, neat palmitic acid.

Physicochemical Properties of MoVTeNb Mixed Oxide Catalysts Synthesized using Different Vanadium Sources

The use of different vanadium sources in the synthesis of multi-metal MoVTeNb oxide catalysts has been investigated for their effect on the physicochemical properties of catalysts. Metal oxides were synthesized by slurry method assisted with a microwave irradiation. Vanadium pentoxide (V2O5), vanadyl sulphate (VOSO4) and ammonium metavanadate (NH4VO3) were used as the vanadium sources, respectively. X-ray diffraction (XRD) pattern showed the existence of orthorhombic (M1) phases in all catalysts. The catalyst prepared using V2O5 produced the highest formation of the phase. This was further supported by Inductive Couple Plasma-Atomic Emission Spectroscopy (ICP-AES), which showed that the V2O5 catalyst has the highest V: Mo ratio, mainly responsible for the high catalytic activity. Temperature Programmed Reduction in Hydrogen (H2-TPR) showed better reducibility for the catalyst when compared to the others. Temperature Programmed Reaction (TPRn) confirmed that the oxidants active for propane conversion into acrylic acid were originated from the lattice of the catalyst.

Lewis acid Ni/Al-MCM-41 catalysts for H2-free deoxygenation of Reutealis trisperma oil to biofuels

The activity of mesoporous Al-MCM-41 for deoxygenation of Reutealis trisperma oil (RTO) was enhanced via modification with NiO nanoparticles. Deoxygenation at atmospheric pressure and under H₂ free conditions required acid catalysts to ensure the removal of the oxygenated fragments in triglycerides to form liquid hydrocarbons. NiO at different weight loadings was impregnated onto Al-MCM-41 and the changes of Lewis/Brønsted acidity and mesoporosity of the catalysts were investigated. The activity of Al-MCM-41 was enhanced when impregnated with NiO due to the increase of Lewis acidity originating from NiO nanoparticles and the mesoporosity of Al-MCM-41. Increasing the NiO loading enhanced the Lewis acidity but not Brønsted acidity, leading to a higher conversion towards liquid hydrocarbon yield. Impregnation with 10% of NiO on Al-MCM-41 increased the conversion of RTO to hydrocarbons via the deoxygenation pathway and reduced the products from cracking reaction, consequently enhancing the green diesel (C11–C18) hydrocarbon products.

The activity of mesoporous Al-MCM-41 for deoxygenation of Reutealis trisperma oil (RTO) was enhanced via modification with NiO nanoparticles.

Enhanced CO2 methanation at mild temperature on Ni/zeolite from kaolin: effect of metal-support interface

Catalytic CO₂ hydrogenation to CH₄ offers a viable route for CO₂ conversion into carbon feedstock. The research aimed to enhance CO₂ conversion at low temperature and to increase the stability of Ni catalysts using zeolite as a support. NaZSM-5 (MFI), NaA (LTA), NaY (FAU), and NaBEA (BEA) synthesized from kaolin were impregnated with 15% Ni nanoparticles in order to elucidate the effect of surface area, porosity and basicity of the zeolite in increasing Ni activity at mild temperature of ∼200 °C. A highly dispersed Ni catalyst was produced on high surface area NaY meanwhile the mesoporosity of ZSM-5 has no significant effect in improving Ni dispersion. However, the important role of zeolite mesoporosity was observed on the stability of the catalyst. Premature deactivation of Ni/NaA within 10 h was due to the relatively small micropore size that restricted the CO₂ diffusion, meanwhile Ni/NaZSM-5 with a large mesopore size exhibited catalytic stability for 40 h of reaction. Zeolite NaY enhanced Ni activity at 200 °C to give 21% conversion with 100% CH₄ selectivity. In situ FTIR analysis showed the formation of hydrogen carbonate species and formate intermediates at low temperatures on Ni/NaY, which implied the efficiency of electron transfer from the basic sites of NaY during CO₂ reduction. The combination of Ni/NaY interfacial interaction and NaY surface basicity promoted CO₂ methanation reaction at low temperature.

Different Na-zeolites as supports of Ni metal were successfully synthesized from kaolin-based material. Combination of interfacial interaction Ni-support and surface basicity promoted CO₂ methanation reaction at a low temperature of ∼200 °C.

Oxidative stress cytotoxicity induced by platinum-doped magnesia nanoparticles in cancer cells

The aim of this study was to prepare, characterize, and determine the in vitro anticancer effects of platinum-doped magnesia (Pt/MgO) nanoparticles. The chemical compositions, functional groups, and size of nanoparticles were determined using X-ray diffraction, Fourier transform infrared spectroscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, and scanning electron microscopy. Pt/MgO nanoparticles were cuboid and in the nanosize range of 30-50 nm. The cytotoxicity of Pt/MgO nanoparticles was determined via the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay on the human lung and colonic cancer cells (A549 and HT29 respectively) and normal human lung and colonic fibroblasts cells (MRC-5 and CCD-18Co repectively). The Pt/MgO nanoparticles were relatively innocuous to normal cells. Pt/MgO nanoparticles downregulated Bcl-2 and upregulated Bax and p53 tumor suppressor proteins in the cancer cells. Pt/MgO nanoparticles also induced production of reactive oxygen species, decreased cellular glutathione level, and increased lipid peroxidation. Thus, the anticancer effects of Pt/MgO nanoparticles were attributed to the induction of oxidative stress and apoptosis. The study showed the potential of Pt/MgO nanoparticles as an anti-cancer compound.

Hierarchical HZSM-5 for Catalytic Cracking of Oleic Acid to Biofuels

Solid acid catalyzed cracking of waste oil-derived fatty acids is an attractive route to hydrocarbon fuels. HZSM-5 is an effective acid catalyst for fatty acid cracking; however, its microporous nature is susceptible to rapid deactivation by coking. We report the synthesis and application of hierarchical HZSM-5 (h-HZSM-5) in which silanization of pre-crystallized zeolite seeds is employed to introduce mesoporosity during the aggregation of growing crystallites. The resulting h-HZSM-5 comprises a disordered array of fused 10–20 nm crystallites and mesopores with a mean diameter of 13 nm, which maintain the high surface area and acidity of a conventional HZSM-5. Mesopores increase the yield of diesel range hydrocarbons obtained from oleic acid deoxygenation from ~20% to 65%, attributed to improved acid site accessibility within the hierarchical network.

Application of Plasmonic Metal Nanoparticles in TiO2-SiO2 Composite as an Efficient Solar-Activated Photocatalyst: A Review Paper

Over the last decade, interest in the utilization of solar energy for photocatalysis treatment processes has taken centre-stage. Researchers had focused on doping TiO₂ with SiO₂ to obtain an efficient degradation rate of various types of target pollutants both under UV and visible-light irradiation. In order to further improve this degradation effect, some researchers resorted to incorporate plasmonic metal nanoparticles such as silver and gold into the combined TiO₂-SiO₂ to fully optimize the TiO₂-SiO₂’s potential in the visible-light region. This article focuses on the challenges in utilizing TiO₂ in the visible-light region, the contribution of SiO₂ in enhancing photocatalytic activities of the TiO₂-SiO₂ photocatalyst, and the ability of plasmonic metal nanoparticles (Ag and Au) to edge the TiO₂-SiO₂ photocatalyst toward an efficient solar photocatalyst.

Promoting dry reforming of methane via bifunctional NiO/dolomite catalysts for production of hydrogen-rich syngas

Extensive effort has been focused on the advancement of an efficient catalyst for CO2 reforming of CH4 to achieve optimum catalytic activity together with cost-effectiveness and high resistance to catalyst deactivation. In this study, for the first time, a new catalytic support/catalyst system of bifunctional NiO/dolomite has been synthesized by a wet impregnation method using low-cost materials, and it shows unique performance in terms of amphoteric sites and self-reduction properties. The catalysts were loaded into a continuous micro-reactor equipped with an online GC-TCD system. The reaction was carried out with a gas mixture consisting of CH4 and CO2 in the ratio of 1 : 1 flowing 30 ml min-1 at 800 °C for 10 h. The physicochemical properties of the synthesized catalysts were determined by various methods including X-ray diffraction (XRD), N2 adsorption-desorption, H2 temperature-programmed reduction (H2-TPR), temperature-programmed desorption of CO2 (TPD-CO2), and temperature-programmed desorption of NH3 (TPD-NH3). The highest catalytic performance of the DRM reaction was shown by the 10% NiO/dolomite catalyst (CH4 & CO2 conversion, χCH4; χCO2 ∼ 98% and H2 selectivity, S H2 = 75%; H2/CO ∼ 1 : 1 respectively). Bifunctional properties of amphoteric sites on the catalyst and self-reduction behaviour of the NiO/dolomite catalyst improved dry reforming of the CH4 process by enhancing CH4 and CO2 conversion without involving a catalyst reduction step, and the catalyst was constantly active for more than 10 h.

Combustion and Emission Performance of CO/NOx/SOx for Green Diesel Blends in a Swirl Burner

Green diesel is one of the alternative energy sources, which is found to be a second-generation biofuel. Green diesel has a similar molecular structure to petroleum diesel but has better diesel properties, sustainability, and environmental benignity. In this study, green diesel was synthesized from waste cooking oil via a deoxygenation reaction process and blended with petroleum diesel to assess the rate of greenhouse gas emissions. The fuel properties of the formed G100 (pure green diesel) were investigated, and the performance of G5 and G20 (a mixture of 5 and 20% green diesel in petroleum diesel) was tested for combustion in an oil burner. The overall test showed that the combustion of the blends of green diesel produced lower CO2 and SO2 emissions than that of petroleum diesel as a result of the rich oxygen-free fuel content. The obtained fuel properties of pure green diesel and blended green diesel are in compliance with ASTM D6751, ASTM D240-17, and EN 14214 standards. Based on these findings, it is shown that blended green diesel is a clean fuel for the environment and a promising alternative fuel for internal combustion engines.

Optimization and Characterization of Mesoporous Sulfonated Carbon Catalyst and Its Application in Modeling and Optimization of Acetin Production

In this study, an optimized mesoporous sulfonated carbon (OMSC) catalyst derived from palm kernel shell biomass was developed using template carbonization and subsequent sulfonation under different temperatures and time conditions. The OMSC catalyst was characterized using acid-base titration, elemental analysis, XRD, Raman, FTIR, XPS, TPD-NH₃, TGA-DTA, SEM, and N₂ adsorption–desorption analysis to reveal its properties. Results proved that the OMSC catalyst is mesoporous and amorphous in structure with improved textural, acidic, and thermal properties. Both FTIR and XPS confirmed the presence of -SO₃H, -OH, and -COOH functional groups on the surface of the catalyst. The OMSC catalyst was found to be efficient in catalyzing glycerol conversion to acetin via an acetylation reaction with acetic acid within a short period of 3 h. Response surface methodology (RSM), based on a two-level, three-factor, face-centered central composite design, was used to optimize the reaction conditions. The results showed that the optimized temperature, glycerol-to-acetic acid mole ratio, and catalyst load were 126 °C, 1:10.4, and 0.45 g, respectively. Under these optimum conditions, 97% glycerol conversion (GC) and selectivities of 4.9, 27.8, and 66.5% monoacetin (MA), diacetin (DA), and triacetin (TA), respectively, were achieved and found to be close to the predicted values. Statistical analysis showed that the regression model, as well as the model terms, were significant with the predicted R² in reasonable agreement with the adjusted R² (<0.2). The OMSC catalyst maintained excellent performance in GC for the five reaction cycles. The selectivity to TA, the most valuable product, was not stable until the fourth cycle, attributable to the leaching of the acid sites.

Development of bimetallic nickel-based catalysts supported on activated carbon for green fuel production

In this work, the catalytic deoxygenation of waste cooking oil (WCO) over acid–base bifunctional catalysts (NiLa, NiCe, NiFe, NiMn, NiZn, and NiW) supported on activated carbon (AC) was investigated. A high hydrocarbon yield above 60% with lower oxygenated species was found in the liquid product, with the product being selective toward n-(C₁₅ + C₁₇)-diesel fractions. The predominance of n-(C₁₅ + C₁₇) hydrocarbons with the concurrent production of CO and CO₂, indicated that the deoxygenation pathway proceeded via decarbonylation and decarboxylation mechanisms. High deoxygenation activity with better n-(C₁₅ + C₁₇) selectivity over NiLa/AC exposed the great synergistic interaction between La and Ni, and the compatibility of the acid–base sites increased the removal of oxygenated species. The effect of La on the deoxygenation reaction performance was investigated and it was found that a high percentage of La species would be beneficial for the removal of C–O bonded species. The optimum deoxygenation activity of 88% hydrocarbon yield with 75% n-(C₁₅ + C₁₇) selectivity was obtained over 20% of La, which strongly evinced that La leads to a greater enhancement of the deoxygenation activity. The NiLa/AC reusability study showed consistent deoxygenation reactions with 80% hydrocarbon yield and 60% n-(C₁₅ + C₁₇) hydrocarbon selectivity within 6 runs.

In this work, the catalytic deoxygenation of waste cooking oil (WCO) over acid–base bifunctional catalysts (NiLa, NiCe, NiFe, NiMn, NiZn, and NiW) supported on activated carbon (AC) was investigated.

Sulfonated SnO2 nanocatalysts via a self-propagating combustion method for esterification of palm fatty acid distillate

Biodiesel derived from palm fatty acid distillate (PFAD) was produced via catalytic esterification using sulfonated tin oxide (HSO₃⁻/SnO₂) as the superacid solid catalyst. In this work, the SnO₂ catalyst was synthesised by the self-propagating combustion (SPC) method, and activated using chlorosulfonic acid. The SPC method was able to produce nano-sized particles with homogenous size and shape that were anchored with many HSO₃⁻ ions, resulting in more exceptional acid properties that effectively esterified the PFAD feedstock into FAMEs (fatty acid methyl esters). Several studies based on metal oxide-based catalysts were also included for comparison. Under the optimised conditions of 9 : 1 (methanol-to-PFAD molar ratio), 4 wt% (catalyst loading), 100 °C (reaction temperature) and 3 h (reaction time), the FFA conversion and FAME yield were 98.9% and 93.8%, respectively. Besides, the sulfonated SnO₂-spc catalyst can be reused in up to five consecutive cycles with an acceptable esterification performance and minimal sulfur leaching. It is worth mentioning that the SPC method is a greener and simpler technique to obtain the nanocatalysts. Overall, the production of FAME from low value, cheaper, abundant, and non-edible PFAD feedstock, assisted by a non-transition metal oxide of sulfonated SnO₂ catalyst, could reduce the cost of biodiesel production.

A facile SPC method gave a superacid sulfonated tin oxide nanocatalyst for the esterification of low-cost palm fatty acid distillate into biodiesel.

Ni, Zn and Fe hydrotalcite-like catalysts for catalytic biomass compound into green biofuel

In this study, the deoxygenation pathway was proposed to eliminate oxygen species from biomass-derived oil, thereby producing a high quality of hydrocarbon chains (green fuel). The catalytic deoxygenation reaction of bio-oil model compound (oleic acid) successfully produced green gasoline (C8–C12) and diesel (C13–C20) via activated hydrotalcite-derived catalysts (i.e. CMgAl, CFeAl, CZnAl and CNiAl). The reaction was performed under inert N2 condition at 300 °C for 3 h, and the liquid products were analysed by GC–MS and GC–FID analyses to determine the hydrocarbon yield and product selectivity. The activity of the catalysts towards the deoxygenation reaction presented the following increasing order: CNiAl > CMgAl > CZnAl > CFeAl. CNiAl produced a hydrocarbon yield of up to 89 %. CNiAl demonstrated the highest selectivity with 83 % diesel production, whereas CMgAl showed the highest gasoline selectivity with 30 %. These results indicated that catalysts with a high acidic profile facilitate C–O cleavage via deoxygenation, producing hydrocarbons (mainly diesel-range hydrocarbons). Meanwhile, highly basic catalysts exhibit significant selectivity towards gasoline-range hydrocarbons via cracking and lead to the occurrence of C–C cleavage. The large surface area of CNiAl (117 m2 g−1) offered high approachability of the reactant with the catalyst’s active sites, thereby promoting high hydrocarbon yield. Consequently, the hydrocarbon yield and selectivity of the deoxygenation products were predominantly influenced by the acid–base properties and structural behaviour (porosity and surface area) of the catalyst.

Ultrathin Assembles of Porous Array for Enhanced H2 Evolution

Since the complexity of photocatalyst synthesis process and high cost of noble cocatalyst leftovers a major hurdle to producing hydrogen (H₂) from water, a noble metal-free Ni-Si/MgO photocatalyst was realized for the first time to generate H₂ effectively under illumination with visible light. The catalyst was produced by means of simple one-pot solid reaction using self-designed metal reactor. The physiochemical properties of photocatalyst were identified by XRD, FESEM, HRTEM, EDX, UV-visible, XPS, GC and PL. The photocatalytic activities of Ni-Si/MgO photocatalyst at different nickel concentrations were evaluated without adjusting pH, applied voltage, sacrificial agent or electron donor. The ultrathin-nanosheet with hierarchically porous structure of catalyst was found to exhibit higher photocatalytic H₂ production than hexagonal nanorods structured catalyst, which suggests that the randomly branched nanosheets are more active surface to increase the light-harvesting efficiency due to its short electron diffusion path. The catalyst exhibited remarkable performance reaching up to 714 µmolh⁻¹ which is higher among the predominant semiconductor catalyst. The results demonstrated that the photocatalytic reaction irradiated under visible light illumination through the production of hydrogen and hydroxyl radicals on metals. The outcome indicates an important step forward one-pot facile approach to prepare noble ultrathin photocatalyst for hydrogen production from water.

Synthesis of bifunctional nanocatalyst from waste palm kernel shell and its application for biodiesel production

The potential of bifunctional nanocatalysts obtained from waste palm kernel shell (PKS) was investigated for one-step transesterification–esterification under mild conditions. State-of-the-art characterization illustrated that the synthesized catalyst has high stability through the thermal test, high BET surface area of 438.08 m² g⁻¹, pore volume of 0.367 cm³ g⁻¹ and pore width of 3.8 nm. The high amount of basicity (8.866 mmol g⁻¹) and acidity (27.016 mmol g⁻¹) promoted the successfulness of simultaneous transesterification–esterification. The investigation revealed that the combination of potassium and copper on activated carbon surface showed good catalytic activity by giving 95.0% FAME yield and 97.3% FFA conversion at a relatively mild condition of 5 wt% catalyst loading, 12 : 1 methanol to oil molar ratio at 80 °C for 4 hours with FAME yield > 80% after 5 reaction cycles. Characterization of the spent catalyst showed that the amount of basicity was reduced to 3.106 mmol g⁻¹, which validated the reduction of the catalytic performance. The usage of waste material was successfully discovered in producing an effective bifunctional catalyst for biodiesel production from waste cooking oil (WCO) and has high potential for commercialization in the future.

The potential of bifunctional nanocatalysts obtained from waste palm kernel shell (PKS) was investigated for one-step transesterification–esterification under mild conditions.

Octanoic acid hydrodeoxygenation over bifunctional Ni/Al-SBA-15 catalysts

Hydroprocessing of fatty carboxylic acids over 5 wt% Ni/Al-SBA-15 reveals a strong dependence of product yield and selectivity on Si : Al ratio.

Production of green biofuel by using a goat manure supported Ni–Al hydrotalcite catalysed deoxygenation process

The high oxygen content in natural biomass resources, such as vegetable oil or biomass-pyrolysed bio oil, is the main constraint in their implementation as a full-scale biofuel for the automotive industry. In the present study, renewable fuel with petrodiesel-like properties was produced via catalytic deoxygenation of oleic acid in the absence of hydrogen (H₂). The deoxygenation pathway of oleic acid to bio-hydrocarbon involves decarboxylation/decarbonylation of the oxygen content from the fatty acid structure in the form of carbon dioxide (CO₂)/carbon monoxide (CO), with the presence of a goat manure supported Ni–Al hydrotalcite (Gm/Ni–Al) catalyst. Goat manure is an abundant bio-waste, containing a high mineral content, urea as well as cellulosic fiber of plants, which is potentially converted into activated carbon. Synthesis of Gm/Ni–Al was carried out by incorporation of pre-activated goat manure (GmA) during co-precipitation of Ni–Al catalyst with 1 : 3, 1 : 1 and 3 : 1 ratios. The physico-chemical properties of the catalysts were characterized by X-ray diffractometry (XRD), Brunauer–Emmet–Teller (BET) surface area, field emission surface electron microscopy (FESEM) and temperature program desorption ammonia (TPD-NH₃) analysers. The catalytic deoxygenation reaction was performed in a batch reactor and the product obtained was characterized by using gas chromatography-mass spectroscopy (GCMS) for compound composition identification as well as gas chromatography-flame ionisation detector (GC-FID) for yield and selectivity determination. The optimization and evaluation were executed using response surface methodology (RSM) in conjunction with central composite design (CCD) with 5-level-3-factors. From the RSM reaction model, it was found that the Gm/Ni–Al 1 : 1 catalysed deoxygenation reaction gives the optimum product yield of 97.9% of hydrocarbon in the range of C₈–C₂₀, with diesel selectivity (C₁₇: heptadecane and heptadecene compounds) of 63.7% at the optimal reaction conditions of: (1) reaction temperature: 327.14 °C, (2) reaction time: 1 h, and (3) catalyst amount: 5 wt%.

Deoxygenation pathway of oleic acid to bio-hydrocarbon involves decarboxylation/decarbonylation of oxygen content from fatty acid structure in the form of carbon dioxide (CO₂)/carbon monoxide (CO), respectively, with the presence of goat manure supported Ni–Al hydrotalcite (Gm/Ni–Al) catalyst.

Nanolayered composite with enhanced ultraviolet ray absorption properties from simultaneous intercalation of sunscreen molecules

Introduction

The potential of layered double hydroxide (LDH) as a host of multiple ultraviolet-ray absorbers was investigated by simultaneous intercalation of benzophenone 4 (B4) and Eusolex^® 232 (EUS) in Zn/Al LDH.

Methods

The nanocomposites were prepared via coprecipitation method at various molar ratios of B4 and EUS.

Results

At equal molar ratios, the obtained nanocomposite showed an intercalation selectivity that is preferential to EUS. However, the selectivity ratio of intercalated anions was shown to be capable of being altered by adjusting the molar ratio of intended guests during synthesis. Dual-guest nanocomposite synthesized with B4:EUS molar ratio 3:1 (ZEB [3:1]) showed an intercalation selectivity ratio of B4:EUS =53:47. Properties of ZEB (3:1) were monitored using powder X-ray diffractometer to show a basal spacing of 21.8 Å. Direct-injection mass spectra, Fourier transform infrared spectra, and ultraviolet–visible spectra confirmed the dual intercalation of both anions into the interlayer regions of dual-guest nanocomposite. The cytotoxicity study of dual-guest nanocomposite ZEB (3:1) on human dermal fibroblast cells showed no significant toxicity until 25 μg/mL.

Conclusion

Overall, the findings demonstrate successful customization of ultraviolet-ray absorbers composition in LDH host.

Anticancer effect of dentatin and dentatin-hydroxypropyl-β-cyclodextrin complex on human colon cancer (HT-29) cell line

Introduction

Dentatin (DEN) (5-methoxy-2, 2-dimethyl-10-(1, 1-dimethyl-2propenyl) dipyran-2-one), a natural compound present in the roots of Clausena excavata Burm f, possesses pro-apoptotic and antiproliferative effects in various cancer cells. Because of its hydrophobicity, it is believed that its complexation with hydroxy-β-cyclodextrin (HPβCD) will make it a potent inhibitor of cancer cell growth. In the current work, the molecular mechanisms of apoptosis induced by DEN and DEN-HPβCD complex were demonstrated in human colon HT-29 cancer cells.

Materials and methods

After the human colon HT-29 cancer cells were treated with DEN and DEN-HPβCD complex, their effects on the expression of apoptotic-regulated gene markers in mitochondria-mediated apoptotic and death receptor pathways were detected by Western blot analysis and reverse transcription polymerase chain reaction. These markers included caspases-9, 3, and 8, cytochrome c, poly (ADP-ribose) polymerase, p53, p21, cyclin A as well as the Bcl-2 family of proteins.

Results

At 3, 6, 12, and 24 µg/mL exposure, DEN and DEN-HPβCD complex significantly affected apoptosis in HT-29 cells through the down-regulation of Bcl-2 and cyclin A in turn, and up-regulation of Bax, p53, p21, cytochrome c at both protein and mRNA levels. DEN and DEN-HPβCD complex also decreased cleaved poly (ADP-ribose) polymerase and induced caspases-3, -8, and -9.

Conclusion

Results of this study indicate that the apoptotic pathway caused by DEN and DEN-HPβCD complex are mediated by the regulation of caspases and Bcl-2 families in human colon HT-29 cancer cells. The results also suggest that DEN-HPβCD complex may have chemotherapeutic benefits for colon cancer patients.

Therapeutic uses of epicatechin in diabetes and cancer

Epicatechin is a natural flavonoid found in green tea. It has been reported to possess an immense antioxidant effect which contributes to its therapeutic effect against a handful of ailments. In this review, we discuss its therapeutic role in the management of two of the most important human diseases; diabetes and cancer. The consumption of epicatechin has been shown to reduce blood glucose levels in diabetic patients, while is anticancer effect was attributed to its antioxidant properties, antiangiogenic and direct cytotoxicity to cancer cells. Although the exact mechanism of action of epicatechin is still being explored, there is no doubt that it is a promising candidate as an alternative. The significance of this review is to highlight the importance of the usage of natural products (in this case, epicatechin) as an alternative for the treatment of two potentially fatal diseases which is diabetes and cancer. The aim of this review is to educate the scientific community on the role of epicatechin in ameliorating the effects of diabetes and cancers on human while understanding the potential mechanisms of these aforementioned effects.

Bio-oil production via catalytic solvolysis of biomass

Recent studies have found that biomass has great potential as a substitute for natural fossil fuels.

Inducing G2/M Cell Cycle Arrest and Apoptosis through Generation Reactive Oxygen Species (ROS)-Mediated Mitochondria Pathway in HT-29 Cells by Dentatin (DEN) and Dentatin Incorporated in Hydroxypropyl-β-Cyclodextrin (DEN-HPβCD)

Dentatin (DEN), purified from the roots of Clausena excavata Burm f., has poor aqueous solubility that reduces its therapeutic application. The aim of this study was to assess the effects of DEN-HPβCD (hydroxypropyl-β-cyclodextrin) complex as an anticancer agent in HT29 cancer cell line and compare with a crystal DEN in dimethyl sulfoxide (DMSO). The exposure of the cancer cells to DEN or DEN-HPβCD complex leads to cell growth inhibition as determined by MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay. To analyze the mechanism, in which DEN or DEN-HPβCD complex causes the death in human colon HT29 cancer cells, was evaluated by the enzyme-linked immunosorbent assay (ELIZA)-based assays for caspase-3, 8, 9, and reactive oxygen species (ROS). The findings showed that an anti-proliferative effect of DEN or DEN-HPβCD complex were via cell cycle arrest at the G2/M phase and eventually induced apoptosis through both mitochondrial and extrinsic pathways. The down-regulation of poly(ADP-ribose) polymerase (PARP) which leaded to apoptosis upon treatment, was investigated by Western-blotting. Hence, complexation between DEN and HPβCD did not diminish or eliminate the effective properties of DEN as anticancer agent. Therefore, it would be possible to resolve the conventional and current issues associated with the development and commercialization of antineoplastic agents in the future.

High Coke-Resistance Pt/Mg1-xNixO Catalyst for Dry Reforming of Methane

A highly active and stable nano structured Pt/Mg_1-xNi_xO catalysts was developed by a simple co-precipitation method. The obtained Pt/Mg_1-xNi_xO catalyst exhibited cubic structure nanocatalyst with a size of 50–80 nm and realized CH₄ and CO₂ conversions as high as 98% at 900°C with excellent stability in the dry reforming of methane. The characterization of catalyst was performed using various kinds of analytical techniques including XRD, BET, XRF, TPR-H₂, TGA, TEM, FESEM, FT-IR, and XPS analyses. Characterization of spent catalyst further confirms that Pt/Mg_1-xNi_xO catalyst has high coke-resistance for dry reforming. Thus, the catalyst demonstrated in this study, offers a promising catalyst for resolving the dilemma between dispersion and reducibility of supported metal, as well as activity and stability during high temperature reactions.

Investigation of Ce(iii) promoter effects on the tri-metallic Pt, Pd, Ni/MgO catalyst in dry-reforming of methane

The DRM reaction on the Pt, Pd, Ni/Mg_1−XCeXO catalyst was studied where the methane molecule was activated on the Ni metal to produce hydrogen gas. The role of the other metals like Pt and Pd impregnated on the surface of the catalyst was shown.

Versatile boiler ash containing potassium silicate for the synthesis of organic carbonates

Boiler ash containing potassium silicate (BA 900) and potassium silicate (K₂SiO₃) were proven to be feasible Lewis acid catalysts for the synthesis of different organic carbonates (glycerol carbonate, ethylene carbonate, and propylene carbonate).

Seeded Growth Route to Noble Calcium Carbonate Nanocrystal

A solution-phase route has been considered as the most promising route to synthesize noble nanostructures. A majority of their synthesis approaches of calcium carbonate (CaCO3) are based on either using fungi or the CO2 bubbling methods. Here, we approached the preparation of nano-precipitated calcium carbonate single crystal from salmacis sphaeroides in the presence of zwitterionic or cationic biosurfactants without external source of CO2. The calcium carbonate crystals were rhombohedron structure and regularly shaped with side dimension ranging from 33-41 nm. The high degree of morphological control of CaCO3 nanocrystals suggested that surfactants are capable of strongly interacting with the CaCO3 surface and control the nucleation and growth direction of calcium carbonate nanocrystals. Finally, the mechanism of formation of nanocrystals in light of proposed routes was also discussed.

Cytotoxicity and physicochemical characterization of iron-manganese-doped sulfated zirconia nanoparticles

Iron-manganese-doped sulfated zirconia nanoparticles with both Lewis and Brønsted acidic sites were prepared by a hydrothermal impregnation method followed by calcination at 650°C for 5 hours, and their cytotoxicity properties against cancer cell lines were determined. The characterization was carried out using X-ray diffraction, thermogravimetric analysis, Fourier transform infrared spectroscopy, Brauner-Emmett-Teller (BET) surface area measurements, X-ray fluorescence, X-ray photoelectron spectroscopy, zeta size potential, and transmission electron microscopy (TEM). The cytotoxicity of iron-manganese-doped sulfated zirconia nanoparticles was determined using 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assays against three human cancer cell lines (breast cancer MDA-MB231 cells, colon carcinoma HT29 cells, and hepatocellular carcinoma HepG2 cells) and two normal human cell lines (normal hepatocyte Chang cells and normal human umbilical vein endothelial cells [HUVECs]). The results suggest for the first time that iron-manganese-doped sulfated zirconia nanoparticles are cytotoxic to MDA-MB231 and HepG2 cancer cells but have less toxicity to HT29 and normal cells at concentrations from 7.8 μg/mL to 500 μg/mL. The morphology of the treated cells was also studied, and the results supported those from the cytotoxicity study in that the nanoparticle-treated HepG2 and MDA-MB231 cells had more dramatic changes in cell morphology than the HT29 cells. In this manner, this study provides the first evidence that iron-manganese-doped sulfated zirconia nanoparticles should be further studied for a wide range of cancer applications without detrimental effects on healthy cell functions.

Synthesis of waste cooking oil based biodiesel via ferric-manganese promoted molybdenum oxide / zirconia nanoparticle solid acid catalyst: influence of ferric and manganese dopants

The utilization of ferric-manganese promoted molybdenum oxide/zirconia (Fe-Mn- MoO3/ZrO2) (FMMZ) solid acid catalyst for production of biodiesel was demonstrated. FMMZ is produced through impregnation reaction followed by calcination at 600°C for 3 h. The characterization of FMMZ had been done using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), thermal gravimetric analysis (TGA), temperature programmed desorption of NH3 (TPD-NH3), transmission electron microscopy(TEM) and Brunner-Emmett-Teller (BET) surface area measurement. The effect of waste cooking oil methyl esters (WCOME's) yield on the reactions variables such as reaction temperature, catalyst loading, molar ratio of methanol/oil and reusability were also assessed. The catalyst was used to convert the waste cooking oil into corresponding methyl esters (95.6%±0.15) within 5 h at 200℃ reaction temperature, 600 rpm stirring speed, 1:25 molar ratio of oil to alcohol and 4% w/w catalyst loading. The reported catalyst was successfully recycled in six connective experiments without loss in activity. Moreover, the fuel properties of WCOME's were also reported using ASTM D 6751 methods.