Ozone's impact on public health: contributions from indoor exposures to ozone and products of ozone-initiated chemistry

A model of the spatiotemporal distribution of ozone-squalene reaction and ozonolysis by-products from human body

Emissions of ozone and its by-products from ozonolysis on human surfaces lead to indoor air pollution. However, the spatiotemporal distribution of such emissions in indoor environments remains unclear, which may introduce bias when assessing human exposure to ozone and ozonolysis byproducts. This study developed a computational fluid dynamics model to describe the physical and chemical processes involved in the emission of ozone-dependent volatile organic compounds from the human body. The results showed that the reaction probability of ozone in the human body depends on the ozone concentration in the bulk air. For ozone concentrations ranging from 28 ppb to 200 ppb, the reaction probabilities ranged from 5.9 × 10-5 to 1.5 × 10-4. The concentrations of ozone and ozonolysis byproducts obtained from the experimental measurements were used for model validation. The ozonolysis by-products were found to be uniformly distributed in the chamber, whereas the ozone distribution showed less uniformity. The ozone concentration near the human surface was approximately 30 %∼50 % of that in the ambient air. Overall, a model was developed to understand the effect of ozone-surface interactions on indoor air quality. This model can be applied to analyze human exposure to ozone and ozonolysis byproducts and for health risk assessment in built environments.

Formation and Transport of Secondary Contaminants Associated with Germicidal Ultraviolet Light Systems in an Occupied Classroom

Germicidal ultraviolet light (GUV) systems are designed to control airborne pathogen transmission in buildings. However, it is important to acknowledge that certain conditions and system configurations may lead GUV systems to produce air contaminants including oxidants and secondary organic aerosols (SOA). In this study, we modeled the formation and dispersion of oxidants and secondary contaminants generated by the operation of GUV systems employing ultraviolet C 254 and 222 nm. Using a three-dimensional computational fluid dynamics model, we examined the breathing zone concentrations of chemical species in an occupied classroom. Our findings indicate that operating GUV 222 leads to an approximate increase of 10 ppb in O3 concentration and 5.2 μg·m-3 in SOA concentration compared to a condition without GUV operation, while GUV 254 increases the SOA concentration by about 1.2 μg·m-3, with a minimal impact on the O3 concentration. Furthermore, increasing the UV fluence rate of GUV 222 from 1 to 5 μW·cm-2 results in up to 80% increase in the oxidants and SOA concentrations. For GUV 254, elevating the UV fluence rate from 30 to 50 μW·cm-2 or doubling the radiating volume results in up to 50% increase in the SOA concentration. Note that indoor airflow patterns, particularly buoyancy-driven airflow (or displacement ventilation), lead to 15-45% lower SOA concentrations in the breathing zone compared to well-mixed airflow. The results also reveal that when the ventilation rate is below 2 h-1, operating GUV 254 has a smaller impact on human exposure to secondary contaminants than GUV 222. However, GUV 254 may generate more contaminants than GUV 222 when operating at high indoor O3 levels (>15 ppb). These results suggest that the design of GUV systems should consider indoor O3 levels and room ventilation conditions.

Volatile Organic Compounds on Rhodes Island, Greece: Implications for Outdoor and Indoor Human Exposure

Volatile organic compounds (VOC) are considered a class of pollutants with a significant presence in indoor and outdoor air and serious health effects. The aim of this study was to measure and evaluate the levels of outdoor and indoor VOCs at selected sites on Rhodes Island, Greece, during the cold and warm periods of 2023. Spatial and seasonal variations were evaluated; moreover, cancer and non-cancer inhalation risks were assessed. For this purpose, simultaneous indoor-outdoor air sampling was carried out on the island of Rhodes. VOCs were determined by Thermal Desorption-Gas Chromatography/Mass Spectroscopy (TD-GC/MS). Fifty-six VOCs with frequencies ≥ 50% were further considered. VOC concentrations (∑56VOCs) at all sites were found to be higher in the warm period. In the warm and cold sampling periods, the highest concentrations were found at the port of Rhodes City, while total VOC concentrations were dominated by alkanes. The Positive Matrix Factorization (PMF) model was applied to identify the VOC emission sources. Non-cancer and cancer risks for adults were within the safe levels.

Ozone generation and chemistry from 222 nm germicidal ultraviolet light in a fragrant restroom

Devices using 222 nm germicidal ultraviolet light (GUV222) have been marketed to reduce virus transmission indoors with low risk of occupant harm from direct UV exposure. GUV222 generates ozone, an indoor air pollutant and oxidant, under constrained laboratory conditions, but the chemistry byproducts of GUV222-generated ozone in real indoor spaces is uncharacterized. We deployed GUV222 in a public restroom, with an air change rate of 1 h-1 one weekend and 2 h-1 the next, to measure ozone formation and byproducts generated from ozone chemistry indoors. Ozone from GUV222 increased background concentrations by 5 ppb on average for both weekends and reacted rapidly (e.g., at rates of 3.7 h-1 for the first weekend and 2.0 h-1 for the second) with gas-phase precursors emitted by urinal screens and on surfaces. These ozone reactions generated volatile organic compound and aerosol byproducts (e.g., up to 2.6 μg m-3 of aerosol mass). We find that GUV222 is enhancing indoor chemistry by at least a factor of two for this restroom. The extent of this enhanced chemistry will likely be different for different indoor spaces and is dependent upon ventilation rates, species and concentrations of precursor VOCs, and surface reactivity. Informed by our measurements of ozone reactivity and background aerosol concentrations, we present a framework for predicting aerosol byproduct formation from GUV222 that can be extended to other indoor spaces. Further research is needed to understand how typical uses of GUV222 could impact air quality in chemically diverse indoor spaces and generate indoor air chemistry byproducts that can affect human health.

How Does Personal Hygiene Influence Indoor Air Quality?

Humans are known to be a continuous and potent indoor source of volatile organic compounds (VOCs). However, little is known about how personal hygiene, in terms of showering frequency, can influence these emissions and their impact on indoor air chemistry involving ozone. In this study, we characterized the VOC composition of the air in a controlled climate chamber (22.5 m3 with an air change rate at 3.2 h-1) occupied by four male volunteers on successive days under ozone-free (∼0 ppb) and ozone-present (37-40 ppb) conditions. The volunteers either showered the evening prior to the experiments or skipped showering for 24 and 48 h. Reduced shower frequency increased human emissions of gas-phase carboxylic acids, possibly originating from skin bacteria. With ozone present, increasing the number of no-shower days enhanced ozone-skin surface reactions, yielding higher levels of oxidation products. Wearing the same clothing over several days reduced the level of compounds generated from clothing-ozone reactions. When skin lotion was applied, the yield of the skin ozonolysis products decreased, while other compounds increased due to ozone reactions with lotion ingredients. These findings help determine the degree to which personal hygiene choices affect the indoor air composition and indoor air exposures.

Cardiorespiratory effects of indoor ozone exposure during sleep and the influencing factors: A prospective study among adults in China

Ambient ozone (O3) is recognized as a significant air pollutant with implications for cardiorespiratory health, yet the effects of indoor O3 exposure have received less consideration. Furthermore, while sleep occupies one-third of life, research on the health consequences of O3 exposure during this crucial period is scarce. This study aimed to investigate associations of indoor O3 during sleep with cardiorespiratory function and potential predisposing factors. A prospective study among 81 adults was conducted in Beijing, China. Repeated measurements of cardiorespiratory indices reflecting lung function, airway inflammation, cardiac autonomic function, blood pressure, systemic inflammation, platelet and glucose were performed on each subject. Real-time concentrations of indoor O3 during sleep were monitored. Associations of O3 with cardiorespiratory indices were evaluated using linear mixed-effect model. Effect modification by baseline lifestyles (diet, physical activity, sleep-related factors) and psychological status (stress and depression) were investigated through interaction analysis. The average indoor O3 concentration during sleep was 20.3 μg/m3, which was well below current Chinese indoor air quality standard of 160 μg/m3. O3 was associated with most respiratory indicators of decreased airway function except airway inflammation; whereas the cardiovascular effects were only manifested in autonomic dysfunction and not in others. An interquartile range increases in O3 at 6-h average was associated with changes of -3.60 % (95 % CI: -6.19 %, -0.93 %) and -9.60 % (95 % CI: -14.53 %, -4.39 %) in FVC and FEF25-75, respectively. Further, stronger effects were noted among participants with specific dietary patterns, poorer sleep and higher level of depression. This study provides the first general population-based evidence that low-level exposure to indoor O3 during sleep has greater effects on the respiratory system than on the cardiovascular system. Our findings identify the respiratory system as an important target for indoor O3 exposure, and particularly highlight the need for greater awareness of indoor air quality, especially during sleep.

Impacts of urban emissions and air quality in São Paulo State, Brazil

Daily violations of air quality have an impact on urban populations and cause damage to the environment. Thus, the study evaluated the violations of the daily concentrations of SO2, NO2, and PM10, in regions of the State of São Paulo (SSP), based on the National Environment Council (CONAMA) resolution no 491/2018 and the World Health Organization (WHO - World Health Organization. (2016). Ambient air pollution: a global assessment of exposure and burden of disease.) criteria. Daily SO2, NO2, and PM10data from 6 air quality stations operated by Environmental Company of the State of São Paulo CETESB (1996-2011) were organized and submitted to quality control, with data faults (gaps) being identified. The imputation of data via spline proved satisfactory in filling in the gaps (r > 0.7 and low values of Standard Error of the Estimate (SEE) and Root Mean Square Error (RMSE). The cluster analysis (CA) applied to SO2 formed only one homogeneous group (G1). Contrariwise, NO2 and PM10 formed two homogeneous groups (G1 and G2) each. The stations that showed the greatest similarity according to the CA were Cerqueira Cesar and Osasco. The cophenetic matrix generated for SO2 (0.83), NO2 (0.79), and PM10 (0.77) indicate a satisfactory adjustment of the dendrograms. The exploratory statistics applied to groups G1 and G2 point to the high variability of outliers. The WHO criteria are more restrictive than CONAMA regarding daily violations, with a reduction in SO2 and an increase in specific years for NO2 and PM10. Such variability is due to the adoption of public policies by the SSP and the influence of meteorological systems, being confirmed by the Run test that indicated oscillations in the time series, mainly in PM10, and also recognized well-defined biannual cycles.

Bangkok school indoor air quality: monitoring and intervention by positive pressure fresh air system

A PM2.5 crisis in Thailand has caused the Thai government and public to be increasingly concerned about children's exposure to PM2.5 during time in school. This study is a part of a project to create a modeled effective school indoor air quality management for the Bangkok Metropolitan Administration (BMA). We measured air quality and environment in 10 Bangkok school rooms, including CO2, CO, O3, PM2.5, PM10, TVOCPID, formaldehyde, airborne bacteria and fungi, and gaseous organic contaminants. The indoor-to-outdoor concentration ratios indicated that either outdoor sources or indoor + outdoor sources were the predominant contributors to PM in naturally ventilated classrooms. Meanwhile, PM levels in air-conditioned classrooms strongly depended on class activities. CO2 measurements showed that the air-conditioned classrooms had a low 0.4 per hour air change rate and total fungal counts also reached 800 CFU m-3. Analysis of gaseous organic compounds showed that the two most abundant were aliphatic and aromatic hydrocarbons, accounting for 60% by mass concentration. Interestingly, 2-ethyl-1-hexanol, a mucous membrane irritant, was detected in all study rooms. In one naturally ventilated classroom, we implemented a positive pressure fresh air system to mitigate in-class PM levels; it kept PM levels below 20 μg m-3 throughout the class day. Students reported a 20-37% increase in satisfaction with the perceived indoor environmental quality and reported reduced rates in all symptoms of the sick building syndrome after implementing the positive pressure system.

A systematic review and meta-analysis of field studies of portable air cleaners: Performance, user behavior, and by-product emissions

Indoor air quality is important for the health of building occupants, and public interest in controlling indoor airborne pathogens increased dramatically with the COVID-19 pandemic. Pollutant concentrations can be controlled locally using portable air cleaners (sometimes called air purifiers), which allow occupants to apply air cleaning technology to meet their needs in the location and times that they find appropriate. This paper provides a systematic review of scientific literature that describes field studies of the effectiveness of portable air cleaners. Over 500 papers were considered, and 148 were reviewed in detail, to extract 35 specific research results (e.g., particulate removal performance) or characteristics (e.g., type of building). These were aggregated to provide an overview of results and approaches to this type of research, and to provide meta-analyses of the results. The review includes: descriptions of the geographical location of the research; rate of publications over time; types of buildings and occupants in the field study; types of air cleaner technology being tested; pollutants being measured; resulting pollutant removal effectiveness; patterns of usage and potential barriers to usage by occupants; and the potential for by-product emissions in some air cleaner technologies. An example result is that 83 of the 148 papers measured reductions in fine particulates (PM2.5) and found a mean reduction of 49 % with standard deviation of 20 %. The aggregated results were approximately normally distributed, ranging from finding no significant reduction up to a maximum above 90 % reduction. Sixteen of the 148 papers considered gaseous pollutants, such as volatile organic compounds, nitrogen dioxide, and ozone; 36 papers considered biological pollutants, such as bacteria, viruses, pollen, fungi, etc. An important challenge, common to several studies, is that occupants run the air cleaners for shorter periods and on low airflow rate settings, because of concerns about noise, drafts, and electricity cost, which significantly reduces air cleaning effectiveness.

Numerical studies of indoor particulate and gaseous micropollutant transport and its impact on human health in densely-occupied spaces

Micropollutants (MPs) have increasingly become a matter of concern owing to potential health risks associated with human inhalation exposure, particularly in densely-occupied indoor environments. This study employed numerical simulations in a traditional built indoor workspace and a public transport cabin to elucidate the transport dynamics and health impacts of particulate and gaseous type of indoor MPs on varying groups of occupants. The risk of infection from pathogen-bearing MPs was evaluated in the workspace using the integrated Eulerian-Lagrangian and modified Wells-Riley model. In the cabin environment, the health impact of inhaled TVOC within the human nasal system was assessed via the integrated nasal-involved manikin model and cancer/non-cancer risk model. The results demonstrated that when ventilation layout was in favour of restricting particulate MPs spread, considerably high health risks (up to 17.22% infection possibility) were generally found in near-fields of emission source (< 2.25 m). Conversely, if the ventilated flow interacts robustly with emission source, every occupant has a minimum 5% infection risk. Incorporating the nasal cavity in the human model offers a nuanced understanding of gaseous MP distributions post-inhalation. Notably, the olfactory and sinus regions displayed heightened vulnerability to TVOC exposure, with a 62.5%-108% concentration increase compared to other nasal areas. Cancer risk assessment plausibly explained the rising occurrence of brain and central nervous system cancer for aircrew members. Non-cancer risk was found acceptable. This study was expected to advance the understanding of environmental pollution and the health risks tied to indoor MPs in densely-populated environments.

Indoor Air Quality Implications of Germicidal 222 nm Light

One strategy for mitigating the indoor transmission of airborne pathogens, including the SARS-CoV-2 virus, is irradiation by germicidal UV light (GUV). A particularly promising approach is 222 nm light from KrCl excimer lamps (GUV222); this inactivates airborne pathogens and is thought to be relatively safe for human skin and eye exposure. However, the impact of GUV222 on the composition of indoor air has received little experimental study. Here, we conduct laboratory experiments in a 150 L Teflon chamber to examine the formation of secondary species by GUV222. We show that GUV222 generates ozone (O3) and hydroxyl radicals (OH), both of which can react with volatile organic compounds to form oxidized volatile organic compounds and secondary organic aerosol particles. Results are consistent with a box model based on the known photochemistry. We use this model to simulate GUV222 irradiation under more realistic indoor air scenarios and demonstrate that under some conditions, GUV222 irradiation can lead to levels of O3, OH, and secondary organic products that are substantially elevated relative to normal indoor conditions. The results suggest that GUV222 should be used at low intensities and in concert with ventilation, decreasing levels of airborne pathogens while mitigating the formation of air pollutants.

Chemical Fate of Oils on Indoor Surfaces: Ozonolysis and Peroxidation

Unsaturated triglycerides found in food and skin oils are reactive in ambient air. However, the chemical fate of such compounds has not been well characterized in genuine indoor environments. Here, we monitored the aging of oil coatings on glass surfaces over a range of environmental conditions, using mass spectrometry, nuclear magnetic resonance (NMR), and electron paramagnetic resonance (EPR) techniques. Upon room air exposure (up to 17 ppb ozone), the characteristic ozonolysis products, secondary ozonides, were observed on surfaces near the cooking area of a commercial kitchen, along with condensed-phase aldehydes. In an office setting, ozonolysis is also the dominant degradation pathway for oil films exposed to air. However, for indoor enclosed spaces such as drawers, the depleted air flow makes lipid autoxidation more favorable after an induction period of a few days. Forming hydroperoxides as the major primary products, this radical-mediated peroxidation behavior is accelerated by indoor direct sunlight, but the initiation step in dark settings is still unclear. These results are in accord with radical measurements, indicating that indoor photooxidation facilitates radical formation on surfaces. Overall, many intermediate and end products observed are reactive oxygen species (ROS) that may induce oxidative stress in human bodies. Given that these species can be widely found on both food and household surfaces, their toxicological properties are worth further attention.

Ozone Loss: A Surrogate for the Indoor Concentration of Ozone-Derived Products

Ozone concentrations tend to be substantially lower indoors than outdoors, largely because of ozone reactions with indoor surfaces. When there are no indoor sources of ozone, a common condition, the net concentration of gaseous products derived from indoor ozone chemistry scales linearly with the difference between outdoor and indoor ozone concentrations, termed "ozone loss." As such, ozone loss is a metric that might be used by epidemiologists to disentangle the adverse health effects of ozone's oxidation products from those of exposure to ozone itself. The present paper examines the characteristics, potential utility, and limitations of the ozone loss concept. We show that for commonly occurring indoor conditions, the ozone loss concentration is directly proportional to the total rate constant for ozone removal on surfaces (ksum) and inversely proportional to the net removal of ozone by air exchange (λ) plus surface reactions (ksum). It follows that the ratio of indoor ozone to ozone loss is equal to the ratio of λ to ksum. Ozone loss is a promising metric for probing potential adverse health effects resulting from exposures to products of indoor ozone chemistry. Notwithstanding its virtues, practitioners using it should be mindful of the limitations discussed in this paper.

Quantifying Ozone-Dependent Emissions of Volatile Organic Compounds from the Human Body

Ozone reactions on human body surfaces produce volatile organic compounds (VOCs) that influence indoor air quality. However, the dependence of VOC emissions on the ozone concentration has received limited attention. In this study, we conducted 36 sets of single-person chamber experiments with three volunteers exposed to ozone concentrations ranging from 0 to 32 ppb. Emission fluxes from human body surfaces were measured for 11 targeted skin-oil oxidation products. For the majority of these products, the emission fluxes linearly correlated with ozone concentration, indicating a constant surface yield (moles of VOC emitted per mole of ozone deposited). However, for the second-generation oxidation product 4-oxopentanal, a higher surface yield was observed at higher ozone concentrations. Furthermore, many VOCs have substantial emissions in the absence of ozone. Overall, these results suggest that the complex surface reactions and mass transfer processes involved in ozone-dependent VOC emissions from the human body can be represented using a simplified parametrization based on surface yield and baseline emission flux. Values of these two parameters were quantified for targeted products and estimated for other semiquantified VOC signals, facilitating the inclusion of ozone/skin oil chemistry in indoor air quality models and providing new insights on skin oil chemistry.

A life course approach to asthma and wheezing among young children caused by ozone: A prospective birth cohort in northern China

BACKGROUND

Given differences in vulnerability of children in early life, a life course approach to asthma and wheezing (AW) in young children caused by ozone (O₃) is not fully understood.

METHODS

We conducted a birth cohort in Jinan, China from 2018 to 2021 to elucidate the onset model of childhood AW due to O₃ exposure. An inverse distance weighted model was used for individual exposure assessment. The time-dependent Cox proportional-hazard model and logistic model were used to investigate the effects of O₃ exposure on AW. Principal component analysis, interaction analysis, and distributed lag model were used to analyze the life course approach.

RESULTS

The cumulative incidence rate for AW among 6501 children aged 2 was 1.4%. A high level of O₃ was related to AW (HR: 2.10, 95% CI: 1.31, 3.37). Only O₃ exposure after birth was associated with AW, with an OR of 1.82 (1.08, 3.12), after adjusting for the effect before birth. Furthermore, adjusting for other air pollutants, the HR for the individual effect of high O₃ exposure on AW was 2.44 (1.53, 3.89). Interestingly, P values for interactions for O₃ and the principal components of other pollutants, as well as the characteristic variable of open windows were less than 0.1. Moreover, an increase in the IQR of O₃ exposure at the 31st to 37th weeks before birth and the 1st to 105th weeks after birth was associated with an increase in the HRs for AW.

CONCLUSIONS

High-level of O₃ exposure after birth could lead to AW among young children. Importantly, the AW onset model may include the risk factors accumulation and the sensitive period model. Specifically, there are two sensitive windows in early life, and the correlated insults between the high level of O₃ and other pollutants as well as open windows in the asthma-inducing effect.

Integrating ambient carbonyl compounds provides insight into the constrained ozone formation chemistry in Zibo city of the North China Plain

Quantifying the impact of carbonyl compounds (carbonyls) on ozone (O₃) photochemical formation is crucial to formulating targeted O₃ mitigation strategies. To investigate the emission source of ambient carbonyls and their integrated observational constraint on the impact of O₃ formation chemistry, a field campaign was conducted in an industrial city (Zibo) of the North China Plain from August to September 2020. The site-to-site variations of OH reactivity for carbonyls were in accordance with the sequence of Beijiao (BJ, urban, 4.4 s^-1) > Xindian (XD, suburban, 4.2 s^-1) > Tianzhen (TZ, suburban, 1.6 s^-1). A 0-D box model (MCMv3.3.1) was applied to assess the O₃-precursor relationship influenced by measured carbonyls. It was found that without carbonyls constraint, the O₃ photochemical production of the three sites was underestimated to varying degrees, and the biases of overestimating the VOC-limited degree were also identified through a sensitivity test to NO_x emission changes, which may be associated with the reactivity of carbonyls. In addition, the results of the positive matrix factorization (PMF) model indicated that the main source of aldehydes and ketones was secondary formation and background (81.6% for aldehydes, 76.8% for ketones), followed by traffic emission (11.0% for aldehydes, 14.0% for ketones). Incorporated with the box model, we found that biogenic emission contributed the most to the O₃ production at the three sites, followed by traffic emission as well as industry and solvent usage. Meanwhile, the relative incremental reactivity (RIR) values of O₃ precursor groups from diverse VOC emission sources featured consistencies and differences at the three sites, which further highlights the importance of the synergetic mitigation of target O₃ precursors at regional and local scales. This study will help to provide targeted policy-guiding O₃ control strategies for other regions.

The effect of ambient ozone exposure on three types of diabetes: a meta-analysis

BACKGROUND

Ozone as an air pollutant is gradually becoming a threat to people's health. However, the effect of ozone exposure on risk of developing diabetes, a fast-growing global metabolic disease, remains controversial.

OBJECTIVE

To evaluate the impact of ambient ozone exposure on the incidence rate of type 1, type 2 and gestational diabetes mellitus.

METHOD

We systematically searched PubMed, Web of Science, and Cochrane Library databases before July 9, 2022, to determine relevant literature. Data were extracted after quality evaluation according to the Newcastle Ottawa Scale (NOS) and the agency for healthcare research and quality (AHRQ) standards, and a meta-analysis was used to evaluate the correlation between ozone exposure and type 1 diabetes mellitus (T1D), type 2 diabetes mellitus (T2D), and gestational diabetes mellitus (GDM). The heterogeneity test, sensitivity analysis, and publication bias were performed using Stata 16.0.

RESULTS

Our search identified 667 studies from three databases, 19 of which were included in our analysis after removing duplicate and ineligible studies. Among the remaining studies, three were on T1D, five were on T2D, and eleven were on GDM. The result showed that ozone exposure was positively correlated with T2D [effect size (ES) = 1.06, 95% CI: 1.02, 1.11] and GDM [pooled odds ratio (OR) = 1.01, 95% CI: 1.00, 1.03]. Subgroup analysis demonstrated that ozone exposure in the first trimester of pregnancy might raise the risk of GDM. However, no significant association was observed between ozone exposure and T1D.

CONCLUSION

Long-term exposure to ozone may increase the risk of T2D, and daily ozone exposure during pregnancy was a hazard factor for developing GDM. Decreasing ambient ozone pollution may reduce the burden of both diseases.

A minireview of recent developments in ozone detection using optical chemodosimeters

The development of optical chemodosimeters for ozone detection has been an important research subject in recent years because of the environmental and biological relevance of ozone. The design and development of ozone chemodosimeters, as well as their numerous applications from 2009 to 2022, have all been thoroughly covered in this minireview. In this review, chemodosimeters are categorised according to their distinctive reaction mechanism with ozone. The comparative data for each of these chemodosimeters have also been provided here. We have also discussed the difficulties and potential prospects of this fast-evolving discipline. To the best of our knowledge, this is the first review that has comprehensively analysed the progress made in the development of ozone chemodosimeters.

Indoor air pollution and human ocular diseases: Associated contaminants and underlying pathological mechanisms

People spend a long time indoors, especially young children. The risk of indoor pollution on human health is one of the current hotspots in environmental and public health. The human ocular surface is highly susceptible to indoor environment quality. Epidemiological data have linked human ophthalmological disorders with exposure to indoor pollution. In this review, we summarized the adverse impacts of indoor pollution on the human ocular surface. Several studies demonstrated that indoor contaminants including particulate matter, volatile/semi-volatile organic compounds, heavy metals, and fuel combustion and cigarette smoke exposure were associated with the incidence of human dry eye, conjunctivitis, glaucoma, cataracts, age-related macular degeneration, and keratitis. In addition, toxicological investigations revealed that indoor pollution-induced induced chronic inflammation, oxidative damage, and disruption of tight junctions are the main underlying pathological mechanisms for ocular surface diseases. Taken together, this review may expand the understanding of pollution-induced eye disorder and highlight the importance of reducing associated contaminants to decrease their detrimental effects on human eyes.

A review of indoor Gaseous organic compounds and human chemical Exposure: Insights from Real-time measurements

Gaseous organic compounds, mainly volatile organic compounds (VOCs), have become a wide concern in various indoor environments where we spend the majority of our daily time. The sources, compositions, variations, and sinks of indoor VOCs are extremely complex, and their potential impacts on human health are less understood. Owing to the deployment of the state-of-the-art real-time mass spectrometry during the last two decades, our understanding of the sources, dynamic changes and chemical transformations of VOCs indoors has been significantly improved. This review aims to summarize the key findings from mass spectrometry measurements in recent indoor studies including residence, classroom, office, sports center, etc. The sources and sinks, compositions and distributions of indoor VOCs, and the factors (e.g., human activities, air exchange rate, temperature and humidity) driving the changes in indoor VOCs are discussed. The physical and chemical processes of gas-particle partitioning and secondary oxidation processes of VOCs, and their impacts on human health are summarized. Finally, the recommendations for future research directions on indoor VOCs measurements and indoor chemistry are proposed.

Evaluating machine learning models to classify occupants' perceptions of their indoor environment and sleep quality from indoor air quality

A variety of factors can affect a person's perception of their environment and health, but one factor that is often overlooked in indoor settings is the air quality. To address this gap, we develop and evaluate four Machine Learning (ML) models on two disparate datasets using Indoor Air Quality (IAQ) parameters as primary features and components of self-reported IAQ satisfaction and sleep quality as target variables. In each case, we compare models to each other as well as to a simple model that always predicts the majority outcome. In the first analysis, we use open-source data collected from 93 California residences to predict occupant's satisfaction with their indoor environment. Results indicate building ventilation rate, Relative Humidity (RH), and formaldehyde are most influential when predicting IAQ perception and do so with an accuracy greater than the simplified model. The second analysis uses IAQ data gathered from a field study we conducted with 20 participants over 11 weeks to train similar models. We obtain accuracy and F1 scores similar to the simplified model where PM_2.5 and TVOCs represent the most important predictors. Our results underscore the ability of IAQ to affect a person's perception of their built environment and health and highlight the utility of ML models to explore the strength of these relationships.Implications: The results from this study show that two outcome variables - occupant's indoor air quality (IAQ) satisfaction and perceived sleep quality - are related to the measured IAQ parameters but not heavily influenced by typical values measured in apartments and homes. This study highlights the ability of machine learning models as exploratory analysis tools to determine underlying relationships within and across datasets in addition to understanding the importance of certain features on the outcome variable. We compare four different models and find that the random forest classifier has the best performance in both analysis on IAQ satisfaction and perceived sleep quality. It is a suitable model for predicting IAQ-related subjective metrics and also provides value insight into the feature importance of the IAQ parameters. The accuracy of any of these machine learning models in predicting occupants' comfort or sleep quality is limited by the dataset size, how data is collected, and range of data. This study identifies the factors that are important to IAQ perception: ventilation rate, relative humidity, and concentrations of formaldehyde, NO2, and particulate matter. It indicates that sensors that can measure these variables are necessary for future, related studies that model occupants' IAQ satisfaction. However, this study does not find strong relationships between any of the IAQ parameters measured in this study and perceived sleep quality despite the logical pathway between these many pollutants and respiratory issues. A prediction model of IAQ perception or sleep quality can be integrated into home management systems to automatically adjust building operations such as ventilation rates in smart buildings. Once buildings are equipped with a network of low-cost sensors that measure concentrations of pollutants and operating conditions of the ventilation system, the prediction model can be used to predict the occupants' comfort and facilitate the control of the ventilation system.

Impact of Climate Change on Indoor Air Quality: A Review

Climate change can affect the indoor environment due to heat and mass transfers between indoor and outdoor environments. To mitigate climate change impacts and adapt buildings to the changing environment, changes in building characteristics and occupants' behavior may occur. To characterize the effects of climate change on indoor air quality (IAQ), the present review focused on four aspects: (1) experimental and modeling studies that relate IAQ to future environmental conditions, (2) evolution of indoor and outdoor air concentrations in the coming years with regard to temperature rise, (3) climate change mitigation and adaptation actions in the building sector, and (4) evolution of human behavior in the context of climate change. In the indoor environment, experimental and modeling studies on indoor air pollutants highlighted a combined effect of temperature and relative humidity on pollutant emissions from indoor sources. Five IAQ models developed for future climate data were identified in the literature. In the outdoor environment, the increasing ambient temperature may lead directly or indirectly to changes in ozone, particle, nitrogen oxides, and volatile organic compound concentrations in some regions of the world depending on the assumptions made about temperature evolution, anthropogenic emissions, and regional regulation. Infiltration into buildings of outdoor air pollutants is governed by many factors, including temperature difference between indoors and outdoors, and might increase in the years to come during summer and decrease during other seasons. On the other hand, building codes in some countries require a higher airtightness for new and retrofitted buildings. The building adaptation actions include the reinforcement of insulation, implementation of new materials and smart building technologies, and a more systematic and possibly longer use of air conditioning systems in summer compared to nowadays. Moreover, warmer winters, springs, and autumns may induce an increasing duration of open windows in these seasons, while the use of air conditioning in summer may reduce the duration of open windows.

Unanticipated Hydrophobicity Increases of Squalene and Human Skin Oil Films Upon Ozone Exposure

The C-H and O-H oscillators on the surfaces of thin films of human-derived skin oil and squalene are probed under ambient conditions (300 K, 1 atm total pressure, 40% RH) using second-order vibrational spectroscopy and contact angle goniometry before and after exposure to ppb amounts of ozone. Skin oil and squalene are found to produce different vibrational sum frequency generation spectra in the C-H stretching region, while exposure to ozone results in surface spectra for both materials that is consistent with a loss of C-H oscillators. The measured contact angles show that the hydrophobicity of the films increases following exposure to ozone, consistent with the reduction in C═C···H₂O ("πH") bonding interactions that is expected from C═C double bond loss due to ozonolysis and indicating that the polar functional groups formed point toward the films' interiors. Implications for heterogeneous indoor chemistry are discussed.

Recent advances on SOA formation in indoor air, fate and strategies for SOA characterization in indoor air - A review

Recent studies proves that indoor air chemistry differs in many aspects from atmospheric one. People send up to 90 % of their life indoors being exposed to pollutants present in gas, particle and solid phase. Particle phase indoor is composed of particles emitted from various sources, among which there is an indoor source - secondary chemical reactions leading to formation of secondary organic aerosol (SOA). Lately, researchers' attentions turned towards the ultrafine particles, for there are still a lot of gaps in knowledge concerning this field of study, while there is evidence of negative influence of ultrafine particles on human health. Presented review sums up current knowledge about secondary particle formation in indoor environment and development of analytical techniques applied to study those processes. The biggest concern today is studying ROS, for their lifetime in indoor air is very short due to reactions at the very beginning of terpene oxidation process. Another interesting aspect that is recently discovered is monoterpene autooxidation process that leads to HOMs formation that in turn can influence SOA formation yield. A complex studies covering gas phase and particle phase characterization, but also toxicological studies are crucial to fully understand indoor air chemistry leading to ultrafine particle formation.

The human oxidation field

Hydroxyl (OH) radicals are highly reactive species that can oxidize most pollutant gases. In this study, high concentrations of OH radicals were found when people were exposed to ozone in a climate-controlled chamber. OH concentrations calculated by two methods using measurements of total OH reactivity, speciated alkenes, and oxidation products were consistent with those obtained from a chemically explicit model. Key to establishing this human-induced oxidation field is 6-methyl-5-hepten-2-one (6-MHO), which forms when ozone reacts with the skin-oil squalene and subsequently generates OH efficiently through gas-phase reaction with ozone. A dynamic model was used to show the spatial extent of the human-generated OH oxidation field and its dependency on ozone influx through ventilation. This finding has implications for the oxidation, lifetime, and perception of chemicals indoors and, ultimately, human health.

Investigation of indoor and outdoor air quality in a university campus during COVID-19 lock down period

The pandemic of COVID-19 currently shadows the world; the whole earth has been on an unprecedented lockdown. Social distancing among people interrupted domestic and international air traffic, suspended industrial productions and economic activities, and had various far-reaching and undetermined implications on air quality. Improvement in air quality has been reported in many cities during the lockdown. On March 22, 2020, the Turkish government enforced strict lockdown measures to reduce coronavirus disease transmission. This lockdown had a significant impact on the movement of people within the country, which resulted in a major drop in worldwide commercial activities. During this period, university campuses were emptied due to the transition to distance education. In this study, various air pollutants sulfur dioxide (SO₂), nitrogen dioxide (NO₂), ozone (O₃), fine particulate matter (PM_2.5), total bacteria, and total fungi were measured in different indoor environments at Eskişehir Technical University Campus in Eskişehir, Turkey during COVID-19 lock down period. Also, to calculate the indoor and outdoor ratios (I/O) of the pollutants, simultaneous outdoor measurements were also carried out. The average indoor SO_2, NO_2, O_3, and PM_2.5 concentrations in different indoor environments ranged between 2.10 and 54.58, 1.36-30.89, 12.01-39.05, and 21-94 μg/m³, respectively. The total number of bacteria and fungi ranged between 21.83-514.15 and 13.10-83.36 CFU/m³, respectively. Our study intends to give a glimpse to quantify the impact of a pandemic on air quality in different indoor environments in a university campus in Eskişehir, Turkey and calls for follow-up studies. Indoor concentrations were evaluated together with outdoor concentrations. In general, it can be said that the calculated I/O ratios for SO₂, NO₂, O₃, bacteria, and fungi were less than 1 in most indoor environments.

Survey of residential indoor particulate matter measurements 1990-2019

We surveyed literature on measurements of indoor particulate matter in all size fractions, in residential environments free of solid fuel combustion (other than wood for recreation or space heating). Data from worldwide studies from 1990 to 2019 were assembled into the most comprehensive collection to date. Out of 2752 publications retrieved, 538 articles from 433 research projects met inclusion criteria and reported unique data, from which more than 2000 unique sets of indoor PM measurements were collected. Distributions of mean concentrations were compiled, weighted by study size. Long-term trends, the impact of non-smoking, air cleaners, and the influence of outdoor PM were also evaluated. Similar patterns of indoor PM distributions for North America and Europe could reflect similarities in the indoor environments of these regions. Greater observed variability for all regions of Asia may reflect greater heterogeneity in indoor conditions, but also low numbers of studies for some regions. Indoor PM concentrations of all size fractions were mostly stable over the survey period, with the exception of observed declines in PM2.5 in European and North American studies, and in PM10 in North America. While outdoor concentrations were correlated with indoor concentrations across studies, indoor concentrations had higher variability, illustrating a limitation of using outdoor measurements to approximate indoor PM exposures.

Integration of Indoor Air Quality Prediction into Healthy Building Design

Healthy building design is an emerging field of architecture and building engineering. Indoor air quality (IAQ) is an inevitable factor that should be considered in healthy building design due to its demonstrated links with human health and well-being. This paper proposes to integrate IAQ prediction into healthy building design by developing a simulation toolbox, termed i-IAQ, using MATLAB App Designer. Within the i-IAQ, users can input information of building layout and wall-openings and select air pollutant sources from the database. As an output, the toolbox simulates indoor levels of carbon dioxide (CO2), total volatile organic compounds (TVOC), inhalable particles (PM10), fine particles (PM2.5), nitrogen dioxide (NO2), and ozone (O3) during the occupied periods. Based on the simulation results, the toolbox also offers diagnosis and recommendations to improve the design. The accuracy of the toolbox was validated by a case study in an apartment where physical measurements of air pollutants took place. The results suggest that designers can integrate the i-IAQ toolbox in building design, so that the potential IAQ issues can be resolved at the early design stage at a low cost. The paper outcomes have the potential to pave a way towards more holistic healthy building design, and novel and cost-effective IAQ management.

Understanding Ozone Transport and Deposition within Indoor Surface Boundary Layers

Ozone-initiated oxidation reactions on indoor surfaces meaningfully alter the chemical composition of indoor air and human exposure to air toxins. Ozone mass transport within the indoor surface boundary layer plays a key role in ozone-surface reaction kinetics. However, limited information is available on detailed ozone transport dynamics near realistic, irregular indoor surfaces. This paper presents a research framework to study the underlying mechanisms of ozone reactions with realistic indoor surfaces based on microscope scanning of surface material and detailed Computational Fluid Dynamics (CFD) simulation. The study results show that indoor surface topography can meaningfully affect ozone mass transport within a surface boundary layer, thereby modulating near-surface ozone concentration gradient and surface uptake. The results also reveal that the effective indoor surface area available for ozone reaction varies with indoor air speed and turbulent air mixing within the boundary layer. The detailed dynamic behaviors of ozone reactions with realistic indoor surfaces provide insights into the implications of pollutant-surface interactions on indoor chemistry and air quality.

Reactions and Products of Squalene and Ozone: A Review

This critical review describes the squalene-ozone (SqOz) reaction, or squalene ozonolysis. Ambient ozone penetrates indoors and drives indoor air chemistry. Squalene, a component of human skin oil, contains six carbon-carbon double bonds and is very reactive with ozone. Bioeffluents from people contribute to indoor air chemistry and affect the indoor air quality, resulting in exposures because people spend the majority of their time indoors. The SqOz reaction proceeds through various formation pathways and produces compounds that include aldehydes, ketones, carboxylic acids, and dicarbonyl species, which have a range of volatilities. In this critical review of SqOz chemistry, information on the mechanism of reaction, reaction probability, rate constants, and reaction kinetics are compiled. Characterizations of SqOz reaction products have been done in laboratory experiments and real-world settings. The effect of multiple environmental parameters (ozone concentration, air exchange rate (AER), temperature, and relative humidity (RH)) in indoor settings are summarized. This critical review concludes by identifying the paucity of available exposure, health, and toxicological data for known reaction products. Key knowledge gaps about SqOz reactions leading to indoor exposures and adverse health outcomes are provided as well as an outlook on where the field is headed.

Multiphase Ozonolysis of Oleic Acid-Based Lipids: Quantitation of Major Products and Kinetic Multilayer Modeling

Commonly found in atmospheric aerosols, cooking oils, and human sebum, unsaturated lipids rapidly decay upon exposure to ozone, following the Criegee mechanism. Here, the gas-surface ozonolysis of three oleic acid-based compounds was studied in a reactor and indoors. Under dry conditions, quantitative product analyses by ¹H NMR indicate up to 79% molar yield of stable secondary ozonides (SOZs) in oxidized triolein and methyl oleate coatings. Elevated relative humidity (RH) significantly suppresses the SOZ yields, enhancing the formation of condensed-phase aldehydes and volatile C9 products. Along with kinetic parameters informed by molecular dynamics simulations, these results were used as constraints in a kinetic multilayer model (KM-GAP) simulating triolein ozonolysis. Covering a wide range of coating thicknesses and ozone levels, the model predicts a much faster decay near the gas-lipid interface compared to the bulk. Although the dependence of RH on SOZ yields is well predicted, the model overestimates the production of H₂O₂ and aldehydes. With negligible dependence on RH, the product composition for oxidized oleic acid is substantially affected by a competitive reaction between Criegee intermediates (CIs) and carboxylic acids. The resulting α-acyloxyalkyl hydroperoxides (α-AAHPs) have much higher molar yields (29-38%) than SOZs (12-16%). Overall, the ozone-lipid chemistry could affect the indoor environment through "crust" accumulation on surfaces and volatile organic compound (VOC) emission. In the atmosphere, the peroxide formation and changes in particle hygroscopicity may have effects on climate. The related health impacts are also discussed.

Emission Rates of Volatile Organic Compounds from Humans

Human-emitted volatile organic compounds (VOCs) are mainly from breath and the skin. In this study, we continuously measured VOCs in a stainless-steel environmentally controlled climate chamber (22.5 m³, air change rate at 3.2 h^-1) occupied by four seated human volunteers using proton transfer reaction time-of-flight mass spectrometry and gas chromatography mass spectrometry. Experiments with human whole body, breath-only, and dermal-only emissions were performed under ozone-free and ozone-present conditions. In addition, the effect of temperature, relative humidity, clothing type, and age was investigated for whole-body emissions. Without ozone, the whole-body total emission rate (ER) was 2180 ± 620 μg h^-1 per person (p^-1), dominated by exhaled chemicals. The ERs of oxygenated VOCs were positively correlated with the enthalpy of the air. Under ozone-present conditions (∼37 ppb), the whole-body total ER doubled, with the increase mainly driven by VOCs resulting from skin surface lipids/ozone reactions, which increased with relative humidity. Long clothing (more covered skin) was found to reduce the total ERs but enhanced certain chemicals related to the clothing. The ERs of VOCs derived from this study provide a valuable data set of human emissions under various conditions and can be used in models to better predict indoor air quality, especially for highly occupied environments.

Achieving a healthy indoor environment by using an emissions barrier to stop the spread of chemicals from a building into the indoor air

An emissions barrier was used in a premises due to complaints about the indoor air quality (IAQ) as a result of emissions from the building in question. The emissions comprised chlorophenols/chloroanisoles and polycyclic aromatic hydrocarbons (PAH) from treated wood and volatile organic compounds (VOCs), mainly 2-ethylhexanol, from polyvinyl chloride (PVC) flooring and the glue used to paste the flooring onto a concrete slab. Attaching the barrier at the surfaces from where the emissions were spread (floor, walls, ceilings) resulted in a fresh and odour-free indoor air. We conclude that using an emissions barrier in buildings made unhealthy by moisture is an efficient way of restoring pleasant and healthy indoor air.

Global burden of chronic obstructive pulmonary disease attributable to ambient ozone in 204 countries and territories during 1990-2019

Ambient ozone becomes one of significant environmental threats to chronic obstructive pulmonary disease (COPD) in recent decades. To date, however, few systematic analyses have been performed to quantify ozone-attributable disease burden, globally and regionally. In this study, we aimed to comprehensively depict the global trend of ozone-related COPD premature deaths and disability-adjusted life years (DALYs). We derived estimates of COPD burden attributable to ambient ozone for 204 countries and territories during 1990-2019 from the Global Burden of Disease Study 2019. We examined the number of deaths and DALYs, as well as age-standardized mortality rate (ASMR) and DALYs rate (ASDR) by sex, socio-demographic index (SDI), countries, and regions. Population attributable fractions (PAFs) were adopted to identify age groups vulnerable to ozone-related COPD. Estimated annual percentage changes (EAPCs) were calculated to assess the temporal trend of ozone-attributable COPD burden (e.g., ASMR and ASDR) between 1990 and 2019, using generalized linear models. Spearman rank correlation was applied to measure the relationships of estimated ASMR, ASDR, and EAPC with SDI. In 2019, COPD attributable to ambient ozone gave rise to 365.22 (95% uncertainty interval: 174.93 to 564.27) thousand deaths and 6.21 (2.99 to 9.63) million DALYs globally, representing a corresponding increase of 76.11% and 56.37% versus 1990. During 1990-2019, however, a yearly decline of 1.07% (0.81 to 1.33) was observed for ASMR and 1.30% (1.07 to 1.52) for ASDR. Considerable gender inequality continues in ozone-attributable COPD burden, with much greater impacts among men, and the gap is enlarged with the increase of age. In all age groups, the fractional contribution of ozone to COPD burden exhibited an overall increasing trend globally for both deaths (8.22% in 1990 versus 11.13% in 2019) and DALYs (6.70% in 1990 versus 8.34% in 2019). The burden of COPD caused by ambient ozone varied substantially by geographical and socioeconomic regions. In 2019, the greatest ASMR and ASDR were seen in South Asia, followed by East Asia and Central Sub-Saharan Africa. Despite the clear drop of age-standardized rates (EAPC<0) in high, high-middle, and middle SDI regions, ASMR and ASDR in low and low-middle SDI regions continuously raised between 1990 and 2019. Higher SDI was found to be associated with lower EAPCs in ASMR (r_s=-0.4405, p<0.001) and ASDR (r_s=-0.4510, p<0.001). Although the global ASMR and ASDR of COPD attributable to ambient ozone have decreased from 1990 to 2019, there has been an unnegligible increase in some low and low-middle SDI regions such as Southeast Asia, South Asia, and Andean Latin America. Findings may have some implications for formulating targeted plans and policies for future COPD prevention and ambient ozone management in different regions.

A Case Study on the Assessment of Chemical and Physical Pollution Levels during the Copying Process

In accordance with sustainable development goals (SDG’s), urgent action should be taken to make the societal and natural environments better for human beings. People spend most of their time indoors, therefore growing attention is devoted to address indoor air pollution. When the sources of anthropogenic indoor air pollution (copiers, laser printers) are operated indoors, then chemical and physical indoor air pollution may be higher than air pollution outdoors. Ozone, aerosol particles and volatile organic compounds are the result of pollution caused by copiers and printers. The research was carried out in a copying room by recording chemical (ozone and aerosol particles) and physical (noise) environmental pollution. To determine instantaneous ozone concentrations in the copying room, an ozone analyzer O3 41M was used, while to evaluate the effect of ozone on the ambient air of the copying room, passive samplers were used. To determine the number and concentration of aerosol particles in the ambient air of the office, a particle counter AZ-5 was used. In addition, a DrDAQ data logger was used to measure noise emitted by the copier and ambient temperature as well as relative air humidity. It was found that the distribution of ozone and aerosol particles in the copying room was mostly determined by the copying intensity. The maximum concentration of ozone and aerosol particles was determined during automatic copying (91–120 copies/min).

Indoor air quality impacts of residential mechanical ventilation system retrofits in existing homes in Chicago, IL

Mechanical ventilation systems are used in residences to introduce ventilation air and dilute indoor-generated pollutants. A variety of ventilation system types can be used in home retrofits, influencing indoor air quality (IAQ) in different ways. Here we describe the Breathe Easy Project, a >2-year longitudinal, pseudo-randomized, crossover study designed to assess IAQ and adult asthma outcomes before and after installing residential mechanical ventilation systems in 40 existing homes in Chicago, IL. Each home received one of three types of ventilation systems: continuous exhaust-only, intermittent powered central-fan-integrated-supply (CFIS), or continuous balanced system with an energy recovery ventilator (ERV). Homes with central heating and/or cooling systems also received MERV 10 filter replacements. Approximately weeklong field measurements were conducted at each home on a quarterly basis throughout the study to monitor environmental conditions, ventilation operation, and indoor and outdoor pollutants, including size-resolved particles (0.3-10 μm), ozone (O₃), nitrogen dioxide (NO₂), carbon dioxide (CO₂), carbon monoxide (CO), and indoor formaldehyde (HCHO). Mean reductions in indoor/outdoor (I/O) ratios across all systems after the intervention were approximately 12% (p = 0.001), 10% (p = 0.008), 42% (p < 0.001), 39% (p = 0.002), and 33% (p = 0.007), for CO₂, NO₂, and estimated PM₁, PM_2.5, and PM₁₀, respectively. There was a reduction in I/O ratios for all measured constituents with each type of system, on average, but with varying magnitude and levels of statistical significance. The magnitudes of mean differences in I/O pollutant concentrations ratios were generally largest for most pollutants in the homes that received continuous balanced with ERV and smallest in the homes that received intermittent CFIS systems, with apparent benefits to providing ventilation continuously rather than intermittently. All ventilation system types maintained similar indoor temperatures during pre- and post-intervention periods.

Indoor ozone: Concentrations and influencing factors

Because people spend most of their time indoors, much of their exposure to ozone occurs in buildings, which are partially protective against outdoor ozone. Measurements in approximately 2000 indoor environments (residences, schools, and offices) show a central tendency for average indoor ozone concentration of 4-6 ppb and an indoor to outdoor concentration ratio of about 25%. Considerable variability in this ratio exists among buildings, as influenced by seven building-associated factors: ozone removal in mechanical ventilation systems, ozone penetration through the building envelope, air-change rates, ozone loss rate on fixed indoor surfaces, ozone loss rate on human occupants, ozone loss by homogeneous reaction with nitrogen oxides, and ozone loss by reaction with gas-phase organics. Among these, the most important are air-change rates, ozone loss rate on fixed indoor surfaces, and, in densely occupied spaces, ozone loss rate on human occupants. Although most indoor ozone originates outdoors and enters with ventilation air, indoor emission sources can materially increase indoor ozone concentrations. Mitigation technologies to reduce indoor ozone concentrations are available or are being investigated. The most mature of these technologies, activated carbon filtration of mechanical ventilation supply air, shows a high modeled health-benefit to cost ratio when applied in densely occupied spaces.

Enhanced activity and water tolerance promoted by Ce on MnO/ZSM-5 for ozone decomposition

Catalytic decomposition is a promising way to eliminate ozone using manganese oxides. However, water-induced deactivation of the catalysts remains a challenge for further application. In this work, a series of Ce-promoted MnO supported on ZSM-5 (Mn-xCe/ZSM-5) were developed for ozone decomposition, which exhibited superior catalytic performance. The catalysts were characterized by multiple techniques. It is indicated that MnO was highly dispersed on ZSM-5 (Mn/ZSM-5), accounting for the high performance of ozone decomposition. Addition of Ce in Mn/ZSM-5 formed abundant redox pairs that promoted electron transfer, and thus exhibited superior ozone decomposition activity. Mn-3Ce/ZSM-5 with medium Ce loading showed the maximum activity by exposing the most active sites. Furthermore, Mn-3Ce/ZSM-5 was highly water-resistant in comparison with Mn/ZSM-5 by modulating the surface acidic property to be beneficial for the water desorption. This work provides an efficient and facile way to fabricate Ce-promoted Mn with low valence for effective and stable decomposition of ozone at room temperature.

Experimental and CFD evaluation of ozone efficacy against coronavirus and enteric virus contamination on public transport surfaces

The limited information about the routes of the transmission of SARS-CoV-2 within the ongoing pandemic scenario mobilized the administration, industry and academy to develop sanitation and disinfection systems for public and private spaces. Ozone has been proposed as an effective disinfection method against enveloped and non-enveloped viruses, including viruses with similar morphology to SARS-CoV-2. Due to this efficacy, numerous gaseous and aqueous phase ozone applications have emerged potentially to inhibit virus persistence in aerosols, surfaces, and water. In this work, a numerical model, a RANS CFD model for ozone dispersion inside tram and underground coach has been developed including the chemical self-decomposition and surface reactions of the ozone. The CFD model has been developed for a real tram coach of 28.6 × 2.4 × 2.2 m (L × W × H) using 1.76 million nodes and the Menter's shear stress transport turbulence model. The model predicts the O₃ concentration needed to meet disinfection criteria and the fluid dynamics inside the public transport coach. The effectiveness of the system has been validated with laboratory and field tests in real full-scale coach using porcine epidemic diarrhea virus (PEDV) and murine norovirus (MNV-1) as SARS-CoV-2 and human norovirus surrogates, respectively. Lab-scale experiments on plastic surfaces demonstrated O₃ disinfection (100 ppm, 95% RH, 25 min) inactivate > 99.8% MNV-1 and PEDV. Additionally, field tests in real full-scale coach demostrate the efficacy of the system as > 98.6% of infectious MNV-1 and > 96.3% PEDV were inactivated.

Does ozone inhalation cause adverse metabolic effects in humans? A systematic review

We utilized a practical, transparent approach for systematically reviewing a chemical-specific evidence base. This approach was used for a case study of ozone inhalation exposure and adverse metabolic effects (overweight/obesity, Type 1 diabetes [T1D], Type 2 diabetes [T2D], and metabolic syndrome). We followed the basic principles of systematic review. Studies were defined as "Suitable" or "Supplemental." The evidence for Suitable studies was characterized as strong or weak. An overall causality judgment for each outcome was then determined as either causal, suggestive, insufficient, or not likely. Fifteen epidemiologic and 33 toxicologic studies were Suitable for evidence synthesis. The strength of the human evidence was weak for all outcomes. The toxicologic evidence was weak for all outcomes except two: body weight, and impaired glucose tolerance/homeostasis and fasting/baseline hyperglycemia. The combined epidemiologic and toxicologic evidence was categorized as weak for overweight/obesity, T1D, and metabolic syndrome,. The association between ozone exposure and T2D was determined to be insufficient or suggestive. The streamlined approach described in this paper is transparent and focuses on key elements. As systematic review guidelines are becoming increasingly complex, it is worth exploring the extent to which related health outcomes should be combined or kept distinct, and the merits of focusing on critical elements to select studies suitable for causal inference. We recommend that systematic review results be used to target discussions around specific research needs for advancing causal determinations.

Unintended Consequences of Air Cleaning Chemistry

Amplified interest in maintaining clean indoor air associated with the airborne transmission risks of SARS-CoV-2 have led to an expansion in the market for commercially available air cleaning systems. While the optimal way to mitigate indoor air pollutants or contaminants is to control (remove) the source, air cleaners are a tool for use when absolute source control is not possible. Interventions for indoor air quality management include physical removal of pollutants through ventilation or collection on filters and sorbent materials, along with chemically reactive processes that transform pollutants or seek to deactivate biological entities. This perspective intends to highlight the perhaps unintended consequences of various air cleaning approaches via indoor air chemistry. Introduction of new chemical agents or reactive processes can initiate complex chemistry that results in the release of reactive intermediates and/or byproducts into the indoor environment. Since air cleaning systems are often continuously running to maximize their effectiveness and most people spend a vast majority of their time indoors, human exposure to both primary and secondary products from air cleaners may represent significant exposure risk. This Perspective highlights the need for further study of chemically reactive air cleaning and disinfection methods before broader adoption.

Chemical changes in thirdhand smoke associated with remediation using an ozone generator

Ozonation is a common remediation approach to eliminate odors from mold, tobacco and fire damage in buildings. Little information exists to: 1) assess its effectiveness; 2) provide guidance on operation conditions; and 3) identify potential risks associated with the presence of indoor ozone and ozonation byproducts. The goal of this study is to evaluate chemical changes in thirdhand smoke (THS) aerosols induced by high levels of ozone, in comparison with THS aerosols aged under similar conditions in the absence of ozone. Samples representing different stages of smoke aging in the absence of ozone, including freshly emitted secondhand smoke (SHS) and THS, were collected inside an 18-m3 room-sized chamber over a period of 42 h after six cigarettes were consumed. The experiments involved collection and analysis of gas phase species including volatile organic compounds (VOCs), volatile carbonyls, semivolatile organic compounds (SVOCs), and particulate matter. VOC analysis was carried out by gas chromatography/mass spectrometry with a thermal desorption inlet (TD-GC/MS), and volatile carbonyls were analyzed by on-line derivatization with dinitrophenylhydrazine (DNPH), followed by liquid chromatography with UV/VIS detection. SVOCs were extracted from XAD-coated denuders and Teflon-coated fiberglass filters in the absence of ozone. In those extracts, tobacco-specific nitrosamines (TSNAs) and other SVOCs were analyzed by gas chromatography with positive chemical ionization-triple quadrupole mass spectrometric detection (GC/PCI-QQQ-MS), and polycyclic aromatic hydrocarbons (PAHs) were quantified by gas chromatography with ion trap mass spectrometric detection (GC/IT-MS) in selected ion monitoring mode. Particulate matter concentration was determined gravimetrically. In a second experiment, a 300 mg h-1 commercial ozone generator was operated during 1 h, one day after smoke was generated, to evaluate the remediation of THS by ozonation. VOCs and volatile carbonyls were analyzed before and after ozonation. Extracts from fabrics that were exposed in the chamber before and after ozonation as surrogates for indoor furnishings were analyzed by GC/IT-MS, and aerosol size distribution was studied with a scanning mobility particle sizer. Ozone concentration was measured with a photometric detector. An estimated 175 mg ozone reacted with THS after 1 h of treatment, corresponding to 58% of the total O3 released during that period. Fabric-bound nicotine was depleted after ozonation, and the surface concentration of PAHs adsorbed to fabric specimens decreased by an order of magnitude due to reaction with ozone, reaching pre-smoking levels. These results suggest that ozonation has the potential to remove harmful THS chemicals from indoor surfaces. However, gas phase concentrations of volatile carbonyls, including formaldehyde, acetaldehyde and acetone were higher immediately after ozonation. Ultrafine particles (UFP, in most cases with size <60 nm) were a major ozonation byproduct. UFP number concentrations peaked shortly after ozonation ended, and remained at higher-than background levels for several hours. Based on these results, minimum re-entry times after ozone treatment were predicted for different indoor scenarios. Clearly defining re-entry times can serve as a practical measure to prevent acute exposures to ozone and harmful ozonation byproducts after treatment. This study evaluated potential benefits and risks associated with THS remediation using ozone, providing insights into this technology.

Observing ozone chemistry in an occupied residence

Outdoor ozone transported indoors initiates oxidative chemistry, forming volatile organic products. The influence of ozone chemistry on indoor air composition has not been directly quantified in normally occupied residences. Here, we explore indoor ozone chemistry in a house in California with two adult inhabitants. We utilize space- and time-resolved measurements of ozone and volatile organic compounds (VOCs) acquired over an 8-wk summer campaign. Despite overall low indoor ozone concentrations (mean value of 4.3 ppb) and a relatively low indoor ozone decay constant (1.3 h^-1), we identified multiple VOCs exhibiting clear contributions from ozone-initiated chemistry indoors. These chemicals include 6-methyl-5-hepten-2-one (6-MHO), 4-oxopentanal (4-OPA), nonenal, and C8-C12 saturated aldehydes, which are among the commonly reported products from laboratory studies of ozone interactions with indoor surfaces and with human skin lipids. These VOCs together accounted for ≥12% molecular yield with respect to house-wide consumed ozone, with the highest net product yield for nonanal (≥3.5%), followed by 6-MHO (2.7%) and 4-OPA (2.6%). Although 6-MHO and 4-OPA are prominent ozonolysis products of skin lipids (specifically squalene), ozone reaction with the body envelopes of the two occupants in this house are insufficient to explain the observed yields. Relatedly, we observed that ozone-driven chemistry continued to produce 6-MHO and 4-OPA even after the occupants had been away from the house for 5 d. These observations provide evidence that skin lipids transferred to indoor surfaces made substantial contributions to ozone reactivity in the studied house.

Predicting U.S. Residential Building Energy Use and Indoor Pollutant Exposures in the Mid-21st Century

The extent to which climate change and other factors will influence building energy use and population exposures to indoor pollutants is not well understood. Here, we develop and apply nationally representative residential energy and indoor pollutant model sets to estimate energy use, indoor pollutant concentrations, and associated chronic health outcomes across the U.S. residential building stock in the mid-21st century. The models incorporate expected changes in meteorological and ambient air quality conditions associated with IPCC RCP 8.5 and assumptions for changes in housing characteristics and population movements while keeping other less predictable factors constant. Site and source energy consumption for residential space-conditioning are predicted to decrease by ∼37-43 and ∼20-31%, respectively, in the 2050s compared to those in a 2010s reference scenario. Population-average indoor concentrations of pollutants of ambient origin are expected to decrease, except for O₃. Holding indoor emission factors constant, indoor concentrations of pollutants with intermittent indoor sources are expected to decrease by <5% (PM_2.5) to >30% (NO₂); indoor concentrations of pollutants with persistent indoor sources (e.g., volatile organic compounds (VOCs)) are predicted to increase by ∼15-45%. We estimate negligible changes in disability-adjusted life-years (DALYs) lost associated with residential indoor pollutant exposures, well within uncertainty, although the attribution among pollutants is predicted to vary.

Physical-Chemical Coupling Model for Characterizing the Reaction of Ozone with Squalene in Realistic Indoor Environments

Squalene can react with indoor ozone to generate a series of volatile and semi-volatile organic compounds, some of which may be skin or respiratory irritants, causing adverse health effects. Better understanding of the ozone/squalene reaction and product transport characteristics is thus important. In this study, we developed a physical-chemical coupling model to describe the behavior of ozone/squalene reaction products, that is, 6-methyl-5-hepten-2-one (6-MHO) and 4-oxopentanal (4-OPA) in the gas phase and skin, by considering the chemical reaction and physical transport processes (external convection, internal diffusion, and surface uptake). Experiments without intervention were performed in a single-family house in California utilizing time- and space-resolved measurements. The key parameters in the model were extracted from 5 day data and then used to predict the behaviors in some other days. Predictions from the present model can reproduce the concentration profiles of the three compounds (ozone, 6-MHO, and 4-OPA) well (R² = 0.82-0.89), indicating high accuracy of the model. Exposure analysis shows that the total amount of 6-MHO and 4-OPA entering the blood capillaries in 4 days can reach 14.6 and 30.1 μg, respectively. The contribution of different sinks to ozone removal in the tested realistic indoor environment was also analyzed.

Comparison of hospitalization and mortality associated with short-term exposure to ambient ozone and PM2.5 in Canada

BACKGROUND

Hospitalization and mortality (H-M) have been linked to air pollution separately. However, previous studies have not adequately compared whether air pollution is a stronger risk factor for hospitalization or mortality. This study aimed to investigate differences in H-M risk from short-term ozone and PM_2.5 exposures, and determine whether differences are modified by season, age, and sex.

METHODS

Daily ozone, PM_2.5, temperature, and all-cause H-M counts (ICD-10, A00-R99) were collected for 22-24 Canadian cities for up to 29 years. Generalized additive Poisson models were employed to estimate associations between each pollutant and health outcome, which were compared across season (warm, cold, or year-round), age (all ages or seniors > 65), and sex.

RESULTS

Overall, ozone and PM_2.5 showed higher season-specific risk of mortality than hospitalization: warm-season ozone: 0.54% (95% credible interval, 0.20, 0.85) vs. 0.14% (0.02, 0.27) per 10 ppb; and year-round PM_2.5: 0.90% (0.33, 1.41) vs. 0.29% (0.03, 0.56) per 10 μg/m³. While age showed little H-M difference, sex appeared to be a modifier of H-M risk. While females had higher mortality risk, males had higher hospitalization risk: for females, ozone 0.87% (0.36, 1.35) vs. -0.03% (-0.18, 0.11) and PM_2.5 1.19% (0.40, 1.90) vs. 0.19% (-0.10, 0.47); and for males ozone 0.20% (-0.28, 0.65) vs. 0.35% (0.18, 0.51).

CONCLUSION

This study found H-M differences attributable to ozone and PM_2.5, suggesting that both are stronger risk factors for mortality than hospitalization. In addition, there were clear H-M differences by sex: specifically, females showed higher mortality risk and males showed higher hospitalization risk.

Total OH Reactivity of Emissions from Humans: In Situ Measurement and Budget Analysis

Humans are a potent, mobile source of various volatile organic compounds (VOCs) in indoor environments. Such direct anthropogenic emissions are gaining importance, as those from furnishings and building materials have become better regulated and energy efficient homes may reduce ventilation. While previous studies have characterized human emissions in indoor environments, the question remains whether VOCs remain unidentified by current measuring techniques. In this study conducted in a climate chamber occupied by four people, the total OH reactivity of air was quantified, together with multiple VOCs measured by proton transfer reaction time-of-flight mass spectrometry (PTR-ToF-MS) and fast gas chromatography-mass spectrometry (fast-GC-MS). Whole-body, breath, and dermal emissions were assessed. The comparison of directly measured OH reactivity and that of the summed reactivity of individually measured species revealed no significant shortfall. Ozone exposure (37 ppb) was found to have little influence on breath OH reactivity but enhanced dermal OH reactivity significantly. Without ozone, the whole-body OH reactivity was dominated by breath emissions, mostly isoprene (76%). With ozone present, OH reactivity nearly doubled, with the increase being mainly caused by dermal emissions of mostly carbonyl compounds (57%). No significant difference in total OH reactivity was observed for different age groups (teenagers/young adults/seniors) without ozone. With ozone present, the total OH reactivity decreased slightly with increasing age.

Indoor secondary organic aerosols: Towards an improved representation of their formation and composition in models

The formation of secondary organic aerosol (SOA) indoors is one of the many consequences of the rich and complex chemistry that occurs therein. Given particulate matter has well documented health effects, we need to understand the mechanism for SOA formation indoors and its resulting composition. This study evaluates some uncertainties that exist in quantifying gas-to-particle partitioning of SOA-forming compounds using an indoor detailed chemical model. In particular, we investigate the impacts of using different methods to estimate compound vapour pressures as well as simulating the formation of highly oxygenated organic molecules (HOM) via auto-oxidation on SOA formation indoors. Estimation of vapour pressures for 136 α-pinene oxidation species by six investigated methods led to standard deviations of 28-216%. Inclusion of HOM formation improved model performance across three of the six assessed vapour pressure estimation methods when comparing against experimental data, particularly when the NO2 concentration was relatively high. We also explored the predicted SOA composition using two product classification methods, the first assuming the molecule is dominated by one functionality according to its name, and the second accounting for the fractional weighting of each functional group within a molecule. The SOA composition was dominated by the HOM species when the NO2-to-α-terpineol ratio was high for both product classification methods, as these conditions promoted formation of the nitrate radical and hence formation of HOM monomers. As the NO2-to-α-terpineol ratio decreased, peroxides and acids dominated the simple classification, whereas for the fractional classification, carbonyl and alcohol groups became more important.