Adsorption of Azo-Dye Orange II from Aqueous Solutions Using a Metal-Organic Framework Material: Iron- Benzenetricarboxylate

Effective removal of malachite green oxalate from aqueous solution using Newbouldia laevis husk/MWCNTs nanocomposite: equilibrium, kinetics, and thermodynamics

The discharge of colored effluent into water bodies is a big concern; hence, the current work was designed to fabricate a superior nanocomposite (NBM) using the Newbouldia laevis husk (NB) and functionalized multiwalled carbon nanotubes (f-MWCNTs) for the adsorption of malachite green oxalate (MGO). Brunauer-Emmett-Teller (BET) surface analysis was used to assess the specific surface area of NB (0.7699 m2 g-1) and NBM (94.006 m2 g-1). Fourier transform infrared spectroscopy (FTIR) was employed to determine the chemical moieties on the surface of the adsorbent. Field emission scanning electron microscopy (FESEM) and thermogravimetric analysis (TGA) were used to analyze the surface morphology and the thermal behavior of the adsorbents. Essential factors of the adsorption process were investigated, and it was revealed that pH 6.0, adsorbent dose of 0.05 g, contact time 80 min, concentration of 100 mg dm-3 and maximum adsorption capacity of 35.78 mg g-1 (NB) and 69.97 mg g-1 (NBM) were the optimal parameters. The NB and NBM adsorption processes followed a pseudo-first-order kinetic model. The exothermic and endothermic adsorptive processes were noticed to be the best descriptions of MGO elimination by NB and NBM, respectively. The uptake of MGO by NB and NBM was best described by models of Freundlich and Langmuir isotherms. Besides, NBM demonstrated uptake efficiency that is >80% after the fourth adsorption/desorption cycle. As a result, NBM has a wide range of possible uses in environmental remediation.

Accessible Eco-Friendly Method for Wastewater Removal of the Azo Dye Reactive Black 5 by Reusable Protonated Chitosan-Deep Eutectic Solvent Beads

A novel approach to enhance the utilization of low-cost and sustainable chitosan for wastewater remediation is presented in this investigation. The study centers around the modification of chitosan beads using a deep eutectic solvent composed of choline chloride and urea at a molar ratio of 1:2, followed by treatment with sulfuric acid using an impregnation accessible methodology. The effectiveness of the modified chitosan beads as an adsorbent was evaluated by studying the removal of the azo dye Reactive Black 5 (RB5) from aqueous solutions. Remarkably, the modified chitosan beads demonstrated a substantial increase in adsorption efficiency, achieving excellent removal of RB5 within the concentration range of 25-250 mg/L, ultimately leading to complete elimination. Several key parameters influencing the adsorption process were investigated, including initial RB5 concentration, adsorbent dosage, contact time, temperature, and pH. Quantitative analysis revealed that the pseudo-second-order kinetic model provided the best fit for the experimental data at lower dye concentrations, while the intraparticle diffusion model showed superior performance at higher RB5 concentration ranges (150-250 mg/L). The experimental data were successfully explained by the Langmuir isotherm model, and the maximum adsorption capacities were found to be 116.78 mg/g at 298 K and 379.90 mg/g at 318 K. Desorption studies demonstrated that approximately 41.7% of the dye could be successfully desorbed in a single cycle. Moreover, the regenerated adsorbent exhibited highly efficient RB5 removal (80.0-87.6%) for at least five consecutive uses. The outstanding adsorption properties of the modified chitosan beads can be attributed to the increased porosity, surface area, and swelling behavior resulting from the acidic treatment in combination with the DES modification. These findings establish the modified chitosan beads as a stable, versatile, and reusable eco-friendly adsorbent with high potential for industrial implementation.

Advances in metal-organic frameworks for water remediation applications

Rapid industrialization and agricultural development have resulted in the accumulation of a variety of harmful contaminants in water resources. Thus, various approaches such as adsorption, photocatalytic degradation and methods for sensing water contaminants have been developed to solve the problem of water pollution. Metal-organic frameworks (MOFs) are a class of coordination networks comprising organic-inorganic hybrid porous materials having organic ligands attached to inorganic metal ions/clusters via coordination bonds. MOFs represent an emerging class of materials for application in water remediation owing to their versatile structural and chemical characteristics, such as well-ordered porous structures, large specific surface area, structural diversity, and tunable sites. The present review is focused on recent advances in various MOFs for application in water remediation via the adsorption and photocatalytic degradation of water contaminants. The sensing of water pollutants using MOFs via different approaches, such as luminescence, electrochemical, colorimetric, and surface-enhanced Raman spectroscopic techniques, is also discussed. The high porosity and chemical tunability of MOFs are the main driving forces for their widespread applications, which have huge potential for their commercial use.

CNTs/Fe-BTC Composite Materials for the CO2-Photocatalytic Reduction to Clean Fuels: Batch and Continuous System

CNTs/Fe-BTC composite materials were synthesized with the one-step solvothermal method. MWCNTs and SWCNTs were incorporated in situ during synthesis. The composite materials were characterized by different analytical techniques and used in the CO₂-photocatalytic reduction to value-added products and clean fuels. In the incorporation of CNTs into Fe-BTC, better physical-chemical and optical properties were observed compared to Fe-BTC pristine. SEM images showed that CNTs were incorporated into the porous structure of Fe-BTC, indicating the synergy between them. Fe-BTC pristine showed to be selective to ethanol and methanol; although, it was more selective to ethanol. However, the incorporation of small amounts of CNTs into Fe-BTC not only showed higher production rates but changes in the selectivity compared with the Fe-BTC pristine were also observed. It is important to mention that the incorporation of CNTs into MOF Fe-BTC allowed for increasing the mobility of electrons, decreasing the recombination of charge carriers (electron/hole), and increasing the photocatalytic activity. In both reaction systems (batch and continuous), composite materials showed to be selective towards methanol and ethanol; however, in the continuous system, lower production rates were observed due to the decrease in the residence time compared to the batch system. Therefore, these composite materials are very promising systems to convert CO₂ to clean fuels that could replace fossil fuels soon.

Development of sustainable strontium ferrite graphene nanocomposite for highly effective catalysis and antimicrobial activity

Graphene oxide (GO) has layered structure with carbon atoms that are highly coated with oxygen-containing groups, increasing the interlayer distance while simultaneously making hydrophilic atomic-thick layers. It is exfoliated sheets that only have one or a few layers of carbon atoms. In our work, Strontium Ferrite Graphene Composite (SF@GOC) has been synthesized and thoroughly characterized by physico-chemical methods like XRD, FTIR, SEM-EDX, TEM, AFM, TGA and Nitrogen adsorption desorption analysis. A very few catalysts have been manufactured so far that are capable of degrading Eosin-Y and Orange (II) dyes in water by heterogeneous catalytic method. The current study offers an overview of the recyclable nanocomposite SF@GOC used in mild reaction conditions to breakdown the hazardous water pollutant dyes Eosin-Y (96.2%) and Orange (II) (98.7%). The leaching experiment has demonstrated that the use of the transition metals strontium and iron have not result in any secondary contamination. Moreover, antibacterial and antifungal assay have been investigated. SF@GOC has shown greater activity with bacterial and fungal species while compared with GO. FESEM analysis shows that the bactericidal mechanism for SF@GOC is same in both gram-negative bacteria. The difference in the antifungal activity among the candida strains can be correlated with the movement of ions release (slower and faster) of synthesized nanoscrolls in SF@GOC. In comparison to previous reports, this new environmentally safe and novel catalyst showed substantial degrading activity. It can also be applied to new multifunctional processes such as in the fields of composite materials, solar energy, heterogeneous catalysis and biomedical applications.

Development of a Sustainable Tungsten and Iron Bimetal-Immobilized SBA-15 Composite for Enhanced Wet Catalytic Oxidation of Dye Capacity

In this study, wet catalytic decomposition of Orange (II) dye was carried out with tungsten and iron bimetal-incorporated mesoporous SBA-15 (W-Fe@SBA-15) under visible light. The synthesized hybrid composite material was characterized by physicochemical methods, powder X-ray diffraction (PXRD) spectroscopy, scanning electron microscopy combined with energy-dispersive X-ray (SEM-EDX) spectroscopy studies, Fourier transform infrared (FT-IR) spectroscopy, transmission electron microscopy (TEM), atomic force microscopy (AFM), thermogravimetric analysis (TGA), and surface property studies to understand the nature of the dye degradation process and for catalytic studies. The maximum degradation of Orange (II) dye measured by a UV-visible spectrophotometer was 99% at a contaminant volume of 2.7 × 10^-4 mol/L and a catalyst quantity of 2 g/L in 140 min reaction time. Using gas chromatography-mass spectrometry (GC-MS), the final products were chemically identified. The mechanistic steps of the process were carried out through a series of experiments. The recyclability of the catalyst added a novel feature for such a heterogeneous catalysis that can reduce secondary pollutants in water with no leaching effect observed.

Cross-Linked Ionic Liquid Polymer for the Effective Removal of Ionic Dyes from Aqueous Systems: Investigation of Kinetics and Adsorption Isotherms

In the current study, we have synthesized an imidazolium based cross-linked polymer, namely, 1-vinyl-3-ethylimidazolium bis(trifluoromethylsulfonyl)imide (poly[veim][Tf2N]-TRIM) using trimethylolpropane trimethacrylate as cross linker, and demonstrated its efficiency for the removal of two extensively used ionic dyes—methylene blue and orange-II—from aqueous systems. The detailed characterization of the synthesized poly[veim][Tf2N]-TRIM was performed with the help of 1H NMR, TGA, FT-IR and FE-SEM analysis. The concentration of dyes in aqueous samples before and after the adsorption process was measured using an UV-vis spectrophotometer. The process parameters were optimised, and highest adsorption was obtained at a solution pH of 7.0, adsorbent dosage of 0.75 g/L, contact time of 7 h and dye concentrations of 100 mg/L and 5.0 mg/L for methylene blue and orange-II, respectively. The adsorption kinetics for orange-II and methylene blue were well described by pseudo-first-order and pseudo−second-order models, respectively. Meanwhile, the process of adsorption was best depicted by Langmuir isotherms for both the dyes. The highest monolayer adsorption capacities for methylene blue and orange-II were found to be 1212 mg/g and 126 mg/g, respectively. Overall, the synthesized cross-linked poly[veim][Tf2N]-TRIM effectively removed the selected ionic dyes from aqueous samples and provided >90% of adsorption efficiency after four cycles of adsorption. A possible adsorption mechanism between the synthesised polymeric adsorbent and proposed dyes is presented. It is further suggested that the proposed ionic liquid polymer adsorbent could effectively remove other ionic dyes and pollutants from contaminated aqueous systems.

Photocatalytic Degradation of Dyes Using Titania Nanoparticles Supported in Metal-Organic Materials Based on Iron

Composite materials based on titania nanoparticles (TiO2 NPs) and three metal-organic frameworks (MOFs) called MIL-53 (Fe) ((Fe (III) (OH) (1,4-BDC)), MILs (Materials Institute Lavoisier)), MIL-100 (Fe) (Fe3O(H2O)2OH(BTC)2), and Fe-BTC (iron-benzenetricarboxylate) with different percentages of TiO2 NPs (0.5, 1, and 2.5% wt.) were synthesized using the solvothermal method and used as photocatalytic materials in the degradation of two dyes (Orange II and Reactive Black 5 (RB5)). The pristine and composite materials were characterized with X-ray diffraction, Raman, UV–Vis and Fourier transform infrared spectroscopy and scanning electron microscopy techniques. The 2.5TiO2/MIL-100 composite material showed the best results for the degradation of both dyes (Reactive Black 5 and Orange II dye, 99% and 99.5% degradation in 105 and 150 min, respectively). The incorporation of TiO2 NPs into MOFs can decrease the recombination of the change carrier in the MOF, increasing the photocatalytic activity of a pristine MOF. Results therefore indicated that the synthesized MOF nanocomposites have good potential for wastewater treatment.

Hybrid Nanoarchitectonics with Cr, Fe-MOF/ Graphene Nanocomposite for Removal of Organic Sulfur Compounds from Diesel Fuel

Metal–organic frameworks (Cr-MOF and Fe-MOF) and their graphene hybride nano-composites were prepared via green solvo-themal method. The prepared samples were characterized by XRD, FTIR spectroscopy, N2 adsorption–desorption isotherm and XPS. The composites were used for the adsorption of thiophenic sulfur compound (thiophene, dibenzothiophene, 4,6-dimethyldibenzothiophene) in a model fuel oil. It was found that, graphene in the MOF composite has positive effect on sulfur removal. The removal efficiency increase from 62% to % 95.6 using Fe-MOF and Fe-MOF/Gr (9:1), respectively. This enhancement effect is attributed to a greater number of coordinatively unsaturated sites (CUS) in the composites. The results indicated that the adsorption reach to 96.6% for DBT adsorption from model diesel oil and 62% for diesel fuel on using Cr-MOF/Gr composite.

Activation of Na2S2O8 by α-Fe2O3/CuS composite oxides for the degradation of Orange II under visible light irradiation

Layered α-Fe2O3/CuS nanoflowers with abundant active sites were synthesized by a hydrothermal method.

Ultrasonic-Assisted Synthesis of Fe-BTC-PEG Metal-Organic Complex: An Effective and Safety Nanocarrier for Anticancer Drug Delivery

The porous metal-organic complexes are emerging as novel carriers for effective and safe delivery of drugs for cancer treatment, minimizing the side effect of drug overuse during cancer treatment. This study fabricated the Fe-BTC-PEG metal-organic complex from Fe ions, trimesic acid, and poly(ethylene glycol) as precursors using an ultrasonic-assisted method. The morphology and crystallinity of the resultant complex were observed by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. FTIR spectroscopy was employed to investigate the functional groups on the surface of the Fe-BTC-PEG complex. The result showed that the prepared Fe-BTC-PEG complex was in particle form with low crystallinity and diameter ranging from 100 to 200 nm. The obtained Fe-BTC-PEG complex exhibited a high loading capacity for the 5-fluorouracil (5-FU) anticancer drug with a maximal capacity of 364 mg/g. The releasing behavior of 5-fluorouracil from the 5-FU-loaded Fe-BTC-PEG complex was studied. Notably, the acute oral toxicity of the Fe-BTC-PEG metal-organic complex was also carried out to evaluate the safety of the material in practical application.

Iron-based metal-organic framework: Synthesis, structure and current technologies for water reclamation with deep insight into framework integrity

Water is a supreme requirement for the existence of life, the contamination from the point and non-point sources are creating a great threat to the water ecosystem. Advance tools and techniques are required to restore the water quality and metal-organic framework (MOFs) with a tunable porous structure, striking physical and chemical properties are an excellent candidate for it. Fe-based MOFs, which developed rapidly in recent years, are foreseen as most promising to overcome the disadvantages of traditional water depolluting practices. Fe-MOFs with low toxicity and preferable stability possess excellent performance potential for almost all water remedying techniques in contrast to other MOF structures, especially visible light photocatalysis, Fenton, and Fenton-like heterogeneous catalysis. Fe-MOFs become essential tool for water treatment due to their high catalytic activity, abundant active site and pollutant-specific adsorption. However, the structural degradation under external chemical, photolytic, mechanical, and thermal stimuli is impeding Fe-MOFs from further improvement in activity and their commercialization. Understanding the shortcomings of structural integrity is crucial for large-scale synthesis and commercial implementation of Fe-MOFs-based water treatment techniques. Herein we summarize the synthesis, structure and recent advancements in water remediation methods using Fe-MOFs in particular more attention is paid for adsorption, heterogeneous catalysis and photocatalysis with clear insight into the mechanisms involved. For ease of analysis, the pollutants have been classified into two major classes; inorganic pollutants and organic pollutants. In this review, we present for the first time a detailed insight into the challenges in employing Fe-MOFs for water remediation due to structural instability.

Synthesis of new Zn-decorated metal-organic frameworks for enhanced removal of carcinogenic textile dye: equilibrium and kinetic modeling studies

This paper describes the synthesis and characterization of Zn²⁺ decorated (adipic and terephthalic acid as linkers) piperazine-based metal-organic framework (P-MOFs) and their extraction behavior toward the Chicago sky blue (CSB) dye. The formation of Zn²⁺-decorated P-MOFs was confirmed by FT-IR spectroscopy, energy-dispersive spectroscopy, X-ray diffraction, BET surface area analysis and TGA. Adsorption behavior of the synthesized P-MOFs was explored through solid-phase adsorption (batch method) prior to UV-Vis spectrophotometric determination. Adsorption parameters, including adsorbent dosage, pH of solution, dye concentration, and time, were optimized. Excellent percentage removal of 94% and 95% for AP-Zn-MOF and TP-Zn-MOF, respectively, was achieved at pH 7.5. Kinetics studies indicated that the synthesized adsorbents AP-Zn-MOF and TP-Zn-MOF followed the pseudo-second-order rate model with R² value 0.9989. The Freundlich isotherm with high R² value as compared to Langmuir isotherm indicated that CSB adsorption for the synthesized MOFs follows multilayer adsorption.

Selective Adsorption of Aqueous Diclofenac Sodium, Naproxen Sodium, and Ibuprofen Using a Stable Fe3O4-FeBTC Metal-Organic Frameworka

The FeBTC metal–organic framework (MOF) incorporated with magnetite is proposed as a novel material to solve water contamination with last generation pollutants. The material was synthesized by in situ solvothermal methods, and Fe₃O₄ nanoparticles were added during FeBTC MOF synthesis and used in drug adsorption. X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and Raman spectroscopy characterized the materials, with N₂-physisorption at 77 K. Pseudo-second-order kinetic and Freundlich models were used to describe the adsorption process. The thermodynamic study revealed that the adsorption of three drugs was a feasible, spontaneous exothermic process. The incorporation of magnetite nanoparticles in the FeBTC increased the adsorption capacity of pristine FeBTC. The Fe₃O₄–FeBTC material showed a maximum adsorption capacity for diclofenac sodium (DCF), then by ibuprofen (IB), and to a lesser extent by naproxen sodium (NS). Additionally, hybridization of the FeBTC with magnetite nanoparticles reinforced the most vulnerable part of the MOF, increasing the stability of its thermal and aqueous media. The electrostatic interaction, H-bonding, and interactions in the open-metal sites played vital roles in the drug adsorption. The sites’ competition in the multicomponent mixture’s adsorption showed selective adsorption (DCF) and (NS). This work shows how superficial modification with a low-surface-area MOF can achieve significant adsorption results in water pollutants.

The enhancement of reactive red 24 adsorption from aqueous solution using agricultural waste-derived biochar modified with ZnO nanoparticles

In this study, two types of agricultural wastes, sugarcane bagasse (SB) and cassava root husks (CRHs), were used to fabricate biochars. The pristine biochars derived from SB and CRHs (SBB and CRHB, respectively) were modified using ZnO nanoparticles to generate modified biochars (SBB-ZnO and CRHB-ZnO, respectively) for the removal of Reactive Red 24 (RR24) from stimulated wastewater. Batch experiments were performed to evaluate the effects of ZnO nanoparticles' loading ratio, solution pH, contact time, and initial RR24 concentration on the RR24 adsorption capacity of biochars. The RR24 adsorption isotherm and kinetic data on SBB, SBB-ZnO3, CRHB, and CRHB-ZnO3 were analyzed. Results indicate that SB- and CRH-derived biochars with a ZnO nanoparticle loading ratio of 3 wt% could generate maximum adsorption capacities of RR24 thanks to the double growth on the BET surface of modified biochars. The RR24 adsorption capacities of CRHB-ZnO3 and SBB-ZnO3 reached 81.04 and 105.24 mg g-1, respectively, which were much higher than those of pristine CRHB and SBB (66.19 and 76.14, respectively) at an initial RR24 concentration of 250 mg L-1, pH 3, and contact time of 60 min. The adsorption of RR24 onto biochars agreed well with the pseudo-first-order model and the Langmuir isotherm. The RR24 adsorption capacity on modified biochars, which were reused after five adsorption-desorption cycles showed no insignificant drop. The main adsorption mechanisms of RR24 onto biochars were controlled by electrostatic interactions between biochars' surface positively charged functional groups with azo dye anions, pore filling, hydrogen bonding formation, and π-π interaction.

Adsorption of Malachite Green and Alizarin Red S Dyes Using Fe-BTC Metal Organic Framework as Adsorbent

Synthetic organic dyes are widely used in various industrial sectors but are also among the most harmful water pollutants. In the last decade, significant efforts have been made to develop improved materials for the removal of dyes from water, in particular, on nanostructured adsorbent materials. Metal organic frameworks (MOFs) are an attractive class of hybrid nanostructured materials with an extremely wide range of applications including adsorption. In the present work, an iron-based Fe-BTC MOF, prepared according to a rapid, aqueous-based procedure, was used as an adsorbent for the removal of alizarin red S (ARS) and malachite green (MG) dyes from water. The synthesized material was characterized in detail, while the adsorption of the dyes was monitored by UV-Vis spectroscopy. An optimal adsorption pH of 4, likely due to the establishment of favorable interactions between dyes and Fe-BTC, was found. At this pH and at a temperature of 298 K, adsorption equilibrium was reached in less than 30 min following a pseudo-second order kinetics, with k″ of 4.29 × 10⁻³ and 3.98 × 10⁻² g∙mg⁻¹ min⁻¹ for ARS and MG, respectively. The adsorption isotherm followed the Langmuir model with maximal adsorption capacities of 80 mg∙g⁻¹ (ARS) and 177 mg∙g⁻¹ (MG), and K_L of 9.30·10³ L∙mg⁻¹ (ARS) and 51.56·10³ L∙mg⁻¹ (MG).

Adsorption of Orange II Onto Zn2Al-Layered Double Hydroxide Prepared From Zinc Ash

The dye industry is one of the largest water consuming industries, and at the same time generates large quantities of wastewaters. The resulting wastewaters require proper treatment before discharge, because the dye contents have a negative effect on the water body and organisms present in it. The most efficient treatment method for water containing dyes is represented by adsorption processes. The challenge with these adsorption processes is to develop new, efficient, viable, and economic adsorbent materials. Therefore, in the present paper, the performance of Zn₂Al-layered double hydroxide, prepared from an industrial waste (zinc ash) as a zinc source, was investigated in the Orange II dye adsorption process. The Zn₂Al-layered double hydroxide prepared from secondary sources presents similar morphological and structural characteristics as those prepared from analytical grade reagents. The influence of initial dye concentration, adsorption time, solid:liquid ratio, pH, and temperature was evaluated in order to confirm the benefit of this waste valorization. A comparison with the reference Zn₂Al-layered double hydroxide prepared from analytical grade reagents was performed and the results show that due to the small presence of impurities, the material prepared from zinc ash shows better adsorption capacities (q_max,exp = 42.5 mg/g at 293 K) than the material prepared from reagents (q_max,exp = 36.9 mg/g at 293 K), justifying the utilization of secondary sources for layered double hydroxides preparation. The proposed treatment process presents advantages from both economic and environmental protection point of view.

A Critical Review on Metal-Organic Frameworks and Their Composites as Advanced Materials for Adsorption and Photocatalytic Degradation of Emerging Organic Pollutants from Wastewater

Water-borne emerging pollutants are among the greatest concern of our modern society. Many of these pollutants are categorized as endocrine disruptors due to their environmental toxicities. They are harmful to humans, aquatic animals, and plants, to the larger extent, destroying the ecosystem. Thus, effective environmental remediations of these pollutants became necessary. Among the various remediation techniques, adsorption and photocatalytic degradation have been single out as the most promising. This review is devoted to the compilations and analysis of the role of metal-organic frameworks (MOFs) and their composites as potential materials for such applications. Emerging organic pollutants, like dyes, herbicides, pesticides, pharmaceutical products, phenols, polycyclic aromatic hydrocarbons, and perfluorinated alkyl substances, have been extensively studied. Important parameters that affect these processes, such as surface area, bandgap, percentage removal, equilibrium time, adsorption capacity, and recyclability, are documented. Finally, we paint the current scenario and challenges that need to be addressed for MOFs and their composites to be exploited for commercial applications.

Elimination of cationic azodye from aqueous media using doped polyaniline (PANI): adsorption optimization and modeling

An adsorbent doped polyaniline (PANI) has been explored for the elimination of a cationic azodye, basic red 46 (BR-46), from textile effluent. Essential factors from batch mode have been studied to investigate their effect on the removal of BR-46. The investigated data have been applied to two prevalent adsorption isothermal models (i.e., Langmuir and Freundlich). In addition to the coefficients of determination, six different statistical error functions have been used to identify the most appropriate model for the existing process. The Langmuir model has been shown to be the best adsorption isotherm with minimum error values and a high coefficient of determination value (R2 > 0.999). The maximum monolayer adsorption capacity observed was 1.83 × 10−4 mol g−1 at 50 °C. Thermodynamic parameters of Gibb’s free energy, enthalpy, and entropy were found to be –30.06 KJ mol−1, 374 J mol−1, and 97.25 J mol−1 K−1, respectively. The positive values of enthalpy and entropy indicate the process to be endothermic. The amount of the dye adsorbed increased from 1.02 to 5.42 × 10−5 g in moving from 30 to 50 °C. The measured energy of activation was 17.467 kJ mol−1. The maximum percent removal of BR-46 from wastewater has been 93% at pH 8.

Nickel-Aluminum Oxide Aerogels: Super-adsorbents for Azo Dyes for Water Remediation

Highly porous nickel-aluminum oxide aerogels were prepared according to a one-pot sol-gel process and dried under supercritical carbon dioxide conditions. Although the surface properties of these materials were very appealing for applications in catalysis, these aerogels were never applied in adsorption. The nickel effect on the structure and surface properties of the aerogels has been investigated via a broad range of structural, textural, and morphology characterization of the aerogels before and after heat treatment. The adsorption capacity of the as-synthesized and calcined aerogels for azo dyes was assessed under various experimental conditions. The presence of nickel in the aerogel boosts tremendously the surface reactivity and improves noticeably the adsorption capacity of the material. The adsorption capacities for the nickel-aluminum oxide aerogel with 40% nickel (q max) are 900 mg g-1 for methyl orange, 1484 mg g-1 for orange II, and 1660 mg g-1 for Congo Red. The adsorption process is exothermic and follows pseudo-second-order kinetics.

Enhanced adsorption of methylene blue from textile wastewater by using natural and artificial zeolite

This study investigated the adsorption of methylene blue with natural and artificial zeolite. The effect of pH, contact time, initial concentration and adsorbent dose on adsorption was also investigated. An artificial dye was prepared. Adsorption removal efficiency was low at pH = 2, 3 and 4 but it was quite high at pH = 7. It was determined that the contact time reaches equilibrium within 60 minutes in the adsorption of methylene blue with natural and artificial zeolite. The initial dyestuff concentration for both adsorbents was 5 mg/L. For the removal of methylene blue, a 0.5 g natural and artificial zeolite dosage was sufficient. In order to express the adsorption of natural and artificial zeolite on methylene blue, Langmuir, Freundlich, Temkin and Dubinin-Radushkevich (D-R) isotherm models were examined. In the isotherm study, both natural and artificial zeolite adapted to the Langmuir isotherm model. Langmuir correlation coefficient was 0.998 for artificial zeolite and 0.993 for natural zeolite. Both adsorbent materials best fit into the pseudo-second kinetic model with similar correlation coefficient values of 0.999.

Adsorption kinetics of methyl orange from water by pH-sensitive poly(2-(dimethylamino)ethyl methacrylate)/nanocrystalline cellulose hydrogels

A series of hydrogel nanocomposites was fabricated by in situ polymerization of 2-(dimethylamino)ethyl methacrylate (DMAEMA) in presence of different amounts of (amine- and alkyl-modified) nanocrystalline cellulose (NCC). Modification and nanocomposites properties were proved by different analysis methods such as Fourier-transform infrared spectroscopy (FT-IR), dynamic light scattering (DLS), and field emission scanning electron microscopy (FE-SEM). The new hydrogel nanocomposites were applied for removing methyl orange (MO) used as anionic dye and presented in process water at different pH values. The effects of the fabrication process such as modification and content of NCC, contact time, and pH value on swelling ratio (SR), and equilibrium adsorption kinetics were studied. Results showed that the swelling ratio of PDMAEMA-based nanocomposites varied with the different types of nanoparticles showing the significant effect of the modification process. The MO adsorption into the hydrogel nanocomposites was affected by intermolecular and electrostatic interactions between functional groups of hydrogel and dye. The adsorption capacity decreased at high pH value, and it was significantly affected type of nanoparticles introduced into the hydrogel network. The addition of unmodified NCC did not affect adsorption kinetics significantly. Finally, adsorption kinetics was investigated by pseudo-first-order, pseudo-second-order and intraparticle diffusion models where pseudo-first-order model showed the best correlation with experimental results.

Surface Modification of Bentonite with Polymer Brushes and Its Application as an Efficient Adsorbent for the Removal of Hazardous Dye Orange I

Poly(2-(dimethylamino)ethyl methacrylate)-grafted bentonite, marked as Bent-PDMAEMA, was designed and prepared by a surface-initiated atom transfer radical polymerization method for the first time in this study. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermal gravimetric analysis (TGA) were applied to characterize the structure of Bent-PDMAEMA, which resulted in the successful synthesis of Bent-PDMAEMA. As a cationic adsorbent, the designed Bent-PDMAEMA was used to remove dye Orange I from wastewater. The adsorption property of Bent-PDMAEMA for Orange I dye was investigated under different experimental conditions, such as solution pH, initial dye concentration, contact time and temperature. Under the optimum conditions, the adsorption amount of Bent-PDMAEMA for Orange I dye could reach 700 mg·g-1, indicating the potential application of Bent-PDMAEMA for anionic dyes in the treatment of wastewater. Moreover, the experimental data fitted well with the Langmuir model. The adsorption process obeyed pseudo-second-order kinetic process mechanism.

Carbonized Lanthanum-Based Metal-Organic Framework with Parallel Arranged Channels for Azo-Dye Adsorption

In this contribution, the synthesis of the metal−organic framework (MOF) based on lanthanum that exhibits trigonal prism shape is presented. The length of a single side of this structure ranges from 2 to 10 μm. The carbonized lanthanum-based organic framework (CMOF–La) maintained the original shape. However, the lanthanum oxide was reshaped in the form of rods during the carbonization. It resulted in the creation of parallel arranged channels. The unique structure of the carbonized structure motivated us to reveal its adsorption performance. Therefore, the adsorption kinetics of acid red 18 onto a carbonized metal−organic framework were conducted. Various physicochemical parameters such as initial dye concentration and pH of dye solution were investigated in an adsorption process. The adsorption was found to decrease with an increase in initial dye concentration. In addition, the increase in adsorption capacity was noticed when the solution was changed to basic. Optimal conditions were obtained at a low pH. Kinetic adsorption data were analyzed using the pseudo-first-order kinetic model, the pseudo-second-order kinetic model and the intraparticle diffusion model. The adsorption kinetics were well fitted using a pseudo-second-order kinetic model. It was found that the adsorption of anionic dye onto CMOF–La occurs by hydrophobic interactions between carbonized metal-organic framework and acid red 18.

Leveraging Cu/CuFe2O4-Catalyzed Biomass-Derived Furfural Hydrodeoxygenation: A Nanoscale Metal-Organic-Framework Template Is the Prime Key

Enormous efforts have been initiated in the production of biobased fuels and value-added chemicals via biorefinery owing to the scarcity of fossil resources and huge environmental synchronization. Herein, non-noble metal-based metal/mixed metal oxide supported on carbon employing a metal-organic framework as a sacrificial template is demonstrated for the first time in the selective hydrodeoxygenation (HDO) of biomass-derived furfural (FFR) to 2-methyl furan (MF). The aforementioned catalyst (referred to as Cu/CuFe₂O₄@C-A) exhibited extraordinary catalytic proficiency (100% selectivity toward MF) compared with the conventional Cu/CuFe₂O₄@C-B catalyst which was prepared by the wet impregnation method. High-resolution transmission electron microscopy and synchrotron X-ray diffraction studies evidenced the existence of both metal (Cu) and mixed metal oxide (CuFe₂O₄) phases, in which the metal could help in hydrogenation to alcohol and metal oxide could assist in the hydroxyl group removal step during HDO reaction. The stabilization of encapsulated metal/metal oxide nanoparticles in the carbon matrix, modulation of the electronic structure, and regulation of geometric effects in the Cu/CuFe₂O₄@C-A are thought to play an important role in its excellent catalytic performance, confirmed by X-ray photoelectron spectroscopy and X-ray absorption spectroscopy investigations. Furthermore, the structure and activity interconnection was confirmed by in situ attenuated total reflection-IR studies, which manifested the strong interfacial interaction between FFR and the Cu/CuFe₂O₄@C-A catalyst. This finding was further supported by NH₃ temperature-programmed desorption analysis, which suggested that the presence of more Lewis/weak acidic sites in this catalyst was beneficial for the hydrogenolysis step in HDO reaction. Additionally, H₂ temperature-programmed reduction studies revealed that the adsorption of H₂ was stronger on the Cu/CuFe₂O₄@C-A than that over the conventional Cu/CuFe₂O₄@C-B catalyst; thus, the former catalyst promoted activation of H₂. A detailed kinetic analysis which demonstrated the lower activation energy barrier along with dual active sites attributed for the activation of the two separate reactions in the HDO process on the Cu/CuFe₂O₄@C-A catalyst. This work has great implication in developing a highly stable catalyst for the selective upgradation of biomass without deactivation of metal sites in extended catalytic cycles and opens the door of opportunity for developing a sustainably viable catalyst in biomass refinery industries.

Porous composite architecture bestows Fe-based glassy alloy with high and ultra-durable degradation activity in decomposing azo dye

Since the treatment of wastewater containing azo dye presents problems worldwide, it is important to seek effective materials and technology for the purification of wastewater containing azo dye. Fe-based metallic glasses have been identified as promising materials for the decomposition of dyeing wastewater due to their high chemical activity resulting from their amorphous structure. It is imperative to further improve their degradation performance, and especially their durability, for potential application in wastewater purification. Here, composite structures constructed of porous Ni and amorphous Fe₇₈Si₉B₁₃ powder with markedly enhanced degradation performance in Orange II solution were obtained by utilizing a magnet. Due to the favorable effects of structural electrocatalysis and high dispersity of the distinctive porous architecture in addition to its self-cleaning properties, the solid-liquid interface exhibited strong, continuous electrical and mass transport, and a compelling improvement in degradation performance was achieved. Based on degradation tests and spectrum analysis, the kinetic rate was improved over 11-fold. Moreover, ultra-high durability over 100 cycles was revealed in cycling tests. The results indicate that wastewater degradation performance can be greatly enhanced by properly combining Fe-based metallic glasses with porous material.

A hierarchical LDH/MOF nanocomposite: single, simultaneous and consecutive adsorption of a reactive dye and Cr(vi)

The design and development of an environmentally benign porous adsorbent for effective simultaneous adsorption of organic dyes and heavy metals from water are important but remain a big challenge. Herein, we have designed a layered double hydroxide/metal-organic framework-based hierarchical nanocomposite (LDH/MOF HNC) by a facile, room-temperature in situ approach. This paper for the first time reports a hierarchical trimodal micro-meso-macroporous LDH/MOF composite with a high surface area (surface area 1282 m2 g-1 and pore volume 0.93 cm3 g-1), synthesised by uniformly growing MOF nanocrystals on the surface of LDH nanosheet ultrathin films. An attempt is made to quantitatively demonstrate the adsorption data via suitable nonlinear kinetic and isotherm equations for single, simultaneous, and consecutive adsorption of the orange II reactive dye and Cr(vi). Experiments were performed at various values of pH (6.0-11.0), adsorbent dosages (1.0-8.0 mg), adsorbate concentrations (5-500 mg L-1), and temperatures (293-323 K). The Langmuir model revealed a satisfactory fit to the equilibrium data of the LDH/MOF HNC (correlation coefficients R2 > 0.98) with a calculated maximum adsorption capacity of 1173 and 733 mg g-1 for orange II and Cr(vi), respectively, in a simultaneous adsorption system. The results of the study demonstrated that LDH/MOF HNCs could potentially be applied as a promising nanoadsorbent for the simultaneous removal and extraction of toxic dyes and metals from water.

Sequestrating anionic and cationic dyes from wastewater using spray dried biopolymeric magnetic composite: Experimental and theoretical studies

Spray dried cross-linked chitosan/cobalt ferrite composite was synthesized and applied as an adsorbent for the removal of acid orange II and methylene blue. The composite was structurally, thermally, morphologically and magnetically characterized. The result obtained shows that the magnetic composite was in form of microspheres, while cobalt ferrite was encapsulated in the cross-linked chitosan with saturation magnetization of 10.79 emu g^-1. Adsorption studies revealed that acid orange II adsorbed more favorably on the composite than methylene blue. The adsorption process is spontaneous and exothermic. Liu isotherm model was found to be applicable for the adsorption process. Computational studies showed that the formation of hydrogen bond between acid orange II and the magnetic composite (at both acidic and alkaline pH) contributed to its better adsorption than methylene blue. Adsorption capacity of acid orange II at pH 3 and methylene blue at pH 12 are 542 and 173 mg g^-1 respectively at 303 K base on Liu isotherm model.

Use of metal-organic framework to remove chromium (VI) from aqueous solutions

Chromium is one of the heavy metals found in industrial wastewaters, which have highly toxic to human beings and the environment. Exposure with it may cause some hazard diseases including stomach ulcers, liver, vomiting, kidney and nerve tissue damage, cancer in the lungs, and eventually death. The main objective of this study was to evaluate the efficiency of Uio-66 and ZIF-8 in removing chromium from aqueous solutions. For the synthesis of Uio-66 and ZIF-8, hydrothermal and sol-gel methods were used, respectively. The prepared Uio-66 and ZIF-8 were identified by FTIR, XRD, FE-SEM, EDX, and BET. All experiments were done in batch conditions. Uio-66 and ZIF-8 efficiency for chromium adsorption from aqueous solutions were investigated by variables like initial concentration (10-200 mg/l), pH (3 to 11), Uio-66 and ZIF-8 dosage (0.2 to 1 g/l) and contact time (45 min). The FE-SEM image showed that the sizes of Uio-66 crystals were between 140 and 280 nm. The specific surface area and total pore volume of the prepared Uio-66 and ZIF-8 were 800 m2/g, 0.45 m3/g, 1050 m2/g, and 0.57 m3/g, respectively. The results show chromium adsorption has increased in acid conditions. Equilibrium dosage for Uio-66 and ZIF-8 was 0.4 g/l and 0.6 g/l, respectively. Adsorption equilibrium was performed after 60 min and after this time, chromium adsorption did not significantly change. The study results showed that the experimental data obtained fitted with kinetic model pseudo-order- reaction and isotherm model of Langmuir.

A dual metal organic framework based on copper-iron clusters integrated sulphur doped graphene as a porous material for supercapacitor with remarkable performance characteristics

Herein, a novel bimetallic metal organic framework (MOF) using copper and iron as the metal centers with 1,3,5-tricarboxylic acid as a ligand (CuFeBTC) and its composite with sulphur doped graphene (S-GNS) have been investigated for supercapacitive performance. The synthesis of materials has been carried out using a facile wet chemical route. The physicochemical characterization of the materials employing various structural and surface techniques has been performed which confirms the successful formation of nanocomposite. The capacitive behavior of CuFeBTC, S-GNS and CuFeBTC/S-GNS has been systematically examined using 1 M Na₂SO₄ as an electrolyte in a three and two electrode assembly. The electrochemical studies reveal that CuFeBTC/S-GNS electrode demonstrates highest specific capacitance of 1164.3 F g^-1 at 0.5 A g^-1 with suffice rate capability as compared to CuFeBTC and S-GNS electrodes. Moreover, a symmetric supercapacitor is configured using the CuFeBTC/S-GNS nanocomposite electrodes which deliver remarkable energy and power output of 96.57 Wh kg^-1 and 1595.12 W kg^-1 at an operating voltage of 1.8 V. The as-fabricated symmetric supercapacitor displays competent energy storage retention of 50.2 Wh kg^-1 even at current density of 20.0 A g^-1 with high power density 26973.13 W kg^-1. These deliverables epitomize the latest performance record of bimetallic MOFs based supercapacitors, suggesting that CuFeBTC/S-GNS is a promising active material for high performance electrochemical energy storage applications.

An Easy Synthesis for Preparing Bio-Based Hybrid Adsorbent Useful for Fast Adsorption of Polar Pollutants

For the first time, γ-Al₂O₃ and Bio-Based Substances (BBS) hybrids (A-BBS) were prepared through a simple electrostatic interaction occurring between alumina, used as a support, and BBS (Bio-Based Substance from composted biowastes) carrying positive and negative charges, respectively. We evaluated the optimal amount of BBS to be immobilized on the support and the stability of the resulting A-BBS in order to use this novel hybrid material as an adsorbent for the removal of polar pollutants. Characterization was carried out by X-Ray Diffraction (XRD) for evaluating the crystal structure of the support, Fourier transform infrared spectroscopy (FT-IR) to evidence the presence of BBS on the hybrid material, thermogravimetric analysis (TGA) to measure the thermal stability of the hybrid materials and quantify the BBS amount immobilized on the support, N₂ adsorption at 77 K for the evaluation of the surface area and porosity of the systems, Zeta potential measurements to evaluate the effect of BBS immobilization on the surface charge of the particles and choose the substrates possibly interacting with them. Firstly, we tested the adsorption capability of three samples differently coated with BBS toward cationic species considering various adsorbate/adsorbent ratio. Crystal Violet (CV) was chosen as model pollutant to compare the performance of the hybrid materials with those of other materials described in the literature. The adsorption data were modeled by Langmuir and Freundlich adsorption isotherms. Then, we studied the adsorption capability of the developed material towards molecules with different structures; for this purpose, two contaminants of emerging concerns (carbamazepine and atenolol) were tested. The results indicate that A-BBS could be applied in wastewater treatment for the removal of a significant amount of polar species. In addition, a comparison with literature data concerning CV adsorption was carried out in order to evaluate the environmental impact of synthetic routes used to prepare different adsorbents.