Preparation and Characterization of Chitosan/TiO2 Composite Membranes as Adsorbent Materials for Water Purification

Experimental determination of the mechanical and hydrolytic properties of chitosan/rice husk ash composite membranes

Chitosan-based membranes are promising alternatives to synthetic membranes in a number of specialized use cases, including water purification and electrochemical devices. In application, excessive swelling when hydrated can lead to poor mechanical integrity, necessitating modifications to the polymer so as to counter this effect. Embedding inorganic fillers within an organic polymer matrix is one method of combining excellent mechanical stability with good performance. This study investigated the effect of rice husk ash (RHA) on the mechanical and hydrolytic properties of chitosan-based composite membranes. We incorporated varying amounts of RHA into a chitosan solution and prepared thin film membranes via solution casting. We performed structural, chemical, and mechanical characterizations on the ash and membranes, observing 82.84 % water uptake in the 1.5 weight percent (wt%) RHA-doped membrane and 13.93 MPa tensile strength in the 2.0 wt% loaded composite. As the RHA content increased, the swelling ratio of the composites with RHA loadings greater than 1.0 wt% decreased, indicating an enhancement in mechanical strength. The observed results demonstrate that combining improved mechanical strength with increased water absorption and reduced swelling can lead to optimal membrane characteristics.

Sustainable synthesis and environmental application of chitosan-Ocimum basilicum leaves-ZnO composite membrane for permanganate ion removal in wastewater treatment

This study introduces a novel and environmentally friendly method for developing a cross-linked chitosan-Ocimum basilicum leaves-ZnO (ChOBLZnO) composite membrane, specifically designed for the adsorption of permanganate ions (MnO4-) from wastewater. Various characterization techniques, including Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Brunauer-Emmett-Teller (BET) surface area analysis, were employed to confirm the membrane's synthesis quality, structural integrity, and surface properties crucial for adsorption. The BET analysis revealed a surface area of 228.64 m2/g, indicating a highly porous structure. The membrane exhibited a high adsorption capacity of 142.8 mg/g and an outstanding removal efficiency of 98.5%. The adsorption kinetics were best described by the pseudo-second-order model, with a correlation coefficient (R2) of 0.998, while the Freundlich isotherm model provided the most accurate fit for the adsorption behavior, with an R2 of 0.995. Thermodynamic studies indicated that the adsorption process is spontaneous and endothermic, with negative Gibbs free energy and positive enthalpy and entropy values. Reusability tests showed that the ChOBLZnO composite membrane maintained a high removal efficiency across five cycles, with minimal performance loss. These results demonstrate the ChOBLZnO composite membrane's potential as an efficient and sustainable solution for wastewater treatment, offering both high efficiency and durability.

Fabrication and characterization of a chitosan/cyclodextrin/TiO2-NPs composite for preservation of avocados

In this study, a TiO2 material with nanoparticle size of about 10-20 nm, surface area of 109 m2 g-1 was synthesized using the microwave-assisted hydrothermal method. The chitosan/TiO2 film combined with cyclodextrin (chitosan-cyclodextrin/TiO2, CS-CD/TiO2NPs) helps significantly improve the mechanical properties and enhance the antibacterial activity of the polymer film. Furthermore, the content of TiO2 nanoparticles in CS-CD/TiO2NPs also affects the tensile strength, antibacterial activity, ripening rate, ethylene production rate, and water vapor permeability during food preservation of the CS-CD film that has been studied. The CS-CD/TiO2NPs film is effective against Gram-negative bacteria (Escherichia coli) and Gram-positive bacteria (Staphylococcus aereus) reaching over 99.5% after 15 min of contact. The preservation ability of avocados coated with CS-CD/TiO2NPs was evaluated through some physiological parameters of the avocados, such as sensory evaluation, weight loss, and hardness. The results show that the use of CS-CD/TiO2NPs films extends the preservation time of avocados up to 7 days under conditions of 30 °C and 80% relative humidity.

Interactions between prokaryotic polysaccharides and colloidal magnetic nanoparticles for bacteria removal: A strategy for circumventing antibiotic resistance

Highly stable, colloidal iron oxide nanoparticles with an oxyhydroxide-like surface were used as bacteria-capturing nano-baits. Peptidoglycan isolated from Listeria spp was used as bacteria polysaccharide model, and the nanoparticle binding was characterized showing a Langmuir isotherm constant, KL, equal to 50 ± 3 mL mg-1. The chemical affinity was further supported by dynamic light scattering, transmission electron microscopy, and infrared and UV-Vis data, pointing at the occurrence of extended, coordinative multiple point bindings. The interaction with Gram (+) (Listeria spp) and Gram (-) (Aeromonas veronii) bacteria was shown to be effective and devoid of any toxic effect. Moreover, a real sample, containing a population of several oligotrophic bacteria strains, was incubated with 1 g L-1 of nanoparticle suspension, in the absence of agitation, showing a 100 % capture efficiency, according to plate count. A nanoparticle regeneration method was developed, despite the known irreversibility of such bacterial-nanosurface binding, restoring the bacteria capture capability. This nanomaterial represents a competitive option to eliminate microbiological contamination in water as an alternative strategy to antibiotics, aimed at reducing microbial resistance dissemination. Finally, beyond their excellent features in terms of colloidal stability, binding performances, and biocompatibility this nanoparticle synthesis is cost effective, scalable, and environmentally sustainable.

Surface modified of chitosan by TiO2@MWCNT nanohybrid for the efficient removal of organic dyes and antibiotics

Considering the increase in the discharge of industrial effluents containing dyes and antibiotic resistance as a consequence of increasing the prescription and easy distribution of antibiotic drugs at the global level, designing efficient, biodegradable and non-toxic absorbents is necessary to reduce environmental harm effects. Herein, we present a series of novel eco-friendly ternary hybrid nanocomposite hydrogels CS/TiO2@MWCNT (CTM) composed of chitosan (CS), TiO2, and multiwalled carbon nanotube (MWCNT) for removal of methylene blue (MB) and methyl orange (MO) and common antibiotic ciprofloxacin (CIP) in aqueous medium. The combination of MWCNT and TiO2 improves the physicochemical properties of CS hydrogel and increases the adsorption capacity toward pollutants in the presence of different loadings. CTM hydrogel showed a specific surface area of 236.45 m2 g-1 with a pore diameter of 7.89 nm. Adsorption mechanisms were investigated in detail using kinetic, isotherm, and thermodynamic studies of adsorption as well as various spectroscopic techniques. Adsorption of these pollutants by CTM nanocomposite hydrogel occurred using various interactions at different pHs, which showed the obvious dependence of CTM adsorption capacity on pH. Electrostatic attractions, complex formation, π-π stacking and hydrogen bonds played a key role in the adsorption process. The adsorption of MB, MO, and CIP was fitted with the Langmuir isotherm with maximum adsorption capacities of 531.91, 1763.6, and 1510.5 mg g-1, respectively. CTM had a minor decrease in adsorption strength and showed good structural stability even after 8 adsorptions-desorption cycles. The total cost of producing a 1 kg adsorbent was calculated to be $ 450, which helped us determine the economic feasibility of the adsorbent in large-scale applications.

Phyto-fabricated ZnO nanoparticles for anticancer, photo-antimicrobial effect on carbapenem-resistant/sensitive Pseudomonas aeruginosa and removal of tetracycline

Alternanthera sessilis (AS) leaf extract was used to synthesize zinc oxide nanoparticles (ZnO NPs). Bioanalytical characterization techniques such as X-ray diffraction (XRD) and field emission scanning electron microscope (FESEM) confirmed the formation of crystalline ZnO NPs with average sizes of 40 nm. The AS-ZnO NPs antimicrobial activity was analyzed under dark (D) and white light (WL) conditions. The improved antimicrobial activity was observed against Escherichia coli, Staphylococcus aureus and Bacillus subtilis at the minimal inhibitory concentration (MIC) of 125 and 62.5 µg/mL under WL than the D at 125 and 250 µg/mL for E. coli, B. subtilis, and Pseudomonas aeruginosa, respectively. In contrast, the growth of P. aeruginosa and S. aureus was not completely inhibited until 1 mg/mL AS-ZnO NPs under WL and D. Similarly, AS-ZnO NPs displayed a weaker inhibitory effect against carbapenem-sensitive P. aeruginosa (CSPA) and carbapenem-resistant P. aeruginosa (CRPA) strains of PAC023, PAC041 and PAC032, PAC045 under D. Interestingly, the distinct inhibitory effect was recorded against CSPA PAC041 and CRPA PAC032 in which the bacteria growth was inhibited 99.9% at 250, 500 µg/mL under WL. The cytotoxicity results suggested AS-ZnO NPs demonstrated higher toxicity to MCF-7 breast cancer cells than the RAW264.7 macrophage cells. Further, AS-ZnO NPs exhibited higher catalytic potential against tetracycline hydrochloride (TC-H) degradation at 65.6% and 60.8% under WL than the dark at 59.35% and 48.6% within 120 min. Therefore, AS-ZnO NPs can be used to design a photo-improved antimicrobial formulation and environmental catalyst for removing TC-H from wastewater.

Simultaneous removal of ammonium, phosphate, and phenol via self-assembled biochar composites CBCZrOFe3O4 and its utilization as soil acidity amelioration

High concentrations of ammonium, phosphate, and phenol are recognized as water pollutants that contribute to the degradation of soil acidity. In contrast, small quantities of these nutrients are essential for soil nutrient cycling and plant growth. Here, we reported composite materials comprising biochar, chitosan, ZrO, and Fe3O4, which were employed to mitigate ammonium, phosphate, and phenol contamination in water and to lessen soil acidity. Batch adsorption experiments were conducted to assess the efficacy of the adsorbents. Initially, comparative studies on the simultaneous removal of NH4, PO4, and phenol using CB (biochar), CBC (biochar + chitosan), CBCZrO (biochar + chitosan + ZrO), and CBCZrOFe3O4 (biochar + chitosan + ZrO + Fe3O4) were conducted. The results discovered that CBCZrOFe3O4 exhibited the highest removal percentage among the adsorbents (P < 0.05). Adsorption data for CBCZrOFe3O4 were well fitted to the second-order kinetic and Freundlich isotherm models, with maximum adsorption capacities of 112.65 mg/g for NH4, 94.68 mg/g for PO4 and 112.63 mg/g for phenol. Subsequently, the effect of CBCZrOFe3O4-loaded NH4, PO4, and phenol (CBCZrOFe3O4-APP) on soil acidity was studied over a 60-day incubation period. The findings showed no significant changes (P < 0.05) in soil exchangeable acidity, H+, Mg, K, and Na. However, there was a substantial increase in the soil pH, EC, available P, CEC, N-NH4, and N-NO3. A significant reduction was also observed in the available soil exchangeable Al and Fe (P < 0.05). This technique demonstrated multi-functionality in remediating water pollutants and enhancing soil acidity.

Biomimetic ZrO2-modified seaweed residue with excellent fluorine/ bacteria removal and uranium extraction properties for wastewater purification

Exploring and developing promising biomass composite membranes for the water purification and waste resource utilization is of great significance. The modification of biomass has always been a focus of research in its resource utilization. In this study, we successfully prepare a functional composite membrane, activated graphene oxide/seaweed residue-zirconium dioxide (GOSRZ), with fluoride removal, uranium extraction, and antibacterial activity by biomimetic mineralization of zirconium dioxide nanoparticles (ZrO2 NPs) on seaweed residue (SR) grafted with oxidized graphene (GO). The GOSRZ membrane exhibits highly efficient and specific adsorption of fluoride. For the fluoride concentrations in the range of 100-400 mg/L in water, the removal efficiency can reach over 99 %, even in the presence of interfering ions. Satisfactory extraction rates are also achieved for uranium by the GOSRZ membrane. Additionally, the antibacterial performance studies show that this composite membrane efficiently removes Escherichia coli (E. coli) and Methicillin-resistant Staphylococcus aureus (MRSA). The high adsorption of F- and U(VI) to the composite membrane is ascribed to the ionic exchange and coordination interactions, and its antibacterial activity is caused by the destruction of bacterial cell structure. The sustainability of the biomass composite membranes is further evaluated using the Sustainability Footprint method. This study provides a simple preparation method of biomass composite membrane, expands the water purification treatment technology, and offers valuable guidance for the resource utilization of seaweed waste and the removal of pollutants in wastewater.

Chitosan-Based Biomaterial in Wound Healing: A Review

Wound healing is an evolving and intricate technique that is vital to the restoration of tissue integrity and function. Over the past few decades, chitosan a biopolymer derived from chitin, became known as an emerging biomaterial in the field of healing wounds due to its distinctive characteristics including biocompatibility, biodegradability, affinity to biomolecules, and wound-healing activity. This natural polymer exhibits excellent healing capabilities by accelerating the development of new skin cells, reducing inflammation, and preventing infections. Due to its distinct biochemical characteristics and innate antibacterial activity, chitosan has been extensively researched as an antibacterial wound dressing. Chronic wounds, such as diabetic ulcers and liver disease, are a growing medical problem. Chitosan-based biomaterials are a promising solution in the domain of wound care. The article analyzes the depth of chitosan-based biomaterials and their impact on wound healing and also the methods to enhance the advantages of chitosan by incorporating bioactive compounds. This literature review is aimed to improve the understanding and knowledge about biomaterials and their use in wound healing.

Recent advances in cellulose- and alginate-based hydrogels for water and wastewater treatment: A review

From the environmental perspective, it is essential to develop cheap, eco-friendly, and highly efficient materials for water and wastewater treatment. In this regard, hydrogels and hydrogel-based composites have been widely employed to mitigate global water pollution as this methodology is simple and free from harmful by-products. Notably, alginate and cellulose, which are natural carbohydrate polymers, have gained great attention for their availability, price competitiveness, excellent biodegradability, biocompatibility, hydrophilicity, and superior physicochemical performance in water treatment. This review outlined the recent progress in developing and applying alginate- and cellulose-based hydrogels to remove various pollutants such as dyes, heavy metals, oils, pharmaceutical contaminants, and pesticides from wastewater streams. This review also highlighted the effects of various physical or chemical methods, such as crosslinking, grafting, the addition of fillers, nanoparticle incorporation, and polymer blending, on the physiochemical and adsorption properties of hydrogels. In addition, this review covered the alginate- and cellulose-based hydrogels' current limitations such as low mechanical performance and poor stability, while presenting strategies to improve the drawbacks of the hydrogels. Lastly, we discussed the prospects and future directions of alginate- and cellulose-based hydrogels. We hope this review provides valuable insights into the efficient preparations and applications of hydrogels.

Influence of Lavender Essential Oil on the Physical and Antibacterial Properties of Chitosan Sponge for Hemostatic Applications

Uncontrollable bleeding continues to stand as the primary cause of fatalities globally following surgical procedures, traumatic incidents, disasters, and combat scenarios. The swift and efficient management of bleeding through the application of hemostatic agents has the potential to significantly reduce associated mortality rates. One significant drawback of currently available hemostatic products is their susceptibility to bacterial infections at the bleeding site. As this is a prevalent issue that can potentially delay or compromise the healing process, there is an urgent demand for hemostatic agents with antibacterial properties to enhance survival rates. To mitigate the risk of infection at the site of a lesion, we propose an alternative solution in the form of a chitosan-based sponge and antimicrobial agents such as silver nanoparticles (AgNPs) and lavender essential oil (LEO). The aim of this work is to provide a new type of hemostatic sponge with an antibacterial barrier against a wide range of Gram-positive and Gram-negative microorganisms: Staphylococcus epidermidis 2018 and Enterococcus faecalis VRE 2566 (Gram-positive strains) and Klebsiella pneumoniae ATCC 10031 and Escherichia coli ATCC 35218 (Gram-negative strains).

Photocatalytic degradation of four emerging antibiotic contaminants and toxicity assessment in wastewater: A comprehensive study

Excessive usage and unrestricted discharge of antibiotics in the environment lead to their accumulation in the ecosystem due to their highly stable and non-biodegradation nature. Photodegradation of four most consumed antibiotics such as amoxicillin, azithromycin, cefixime, and ciprofloxacin were studied using Cu2O-TiO2 nanotubes. Cytotoxicity evaluation of the native and transformed products was conducted on the RAW 264.7 cell lines. Photocatalyst loading (0.1-2.0 g/L), pH (5, 7 and 9), initial antibiotic load (50-1000 μg/mL) and cuprous oxide percentage (5, 10 and 20) were optimized for efficient photodegradation of antibiotics. Quenching experiments to evaluate the mechanism of photodegradation with hydroxyl and superoxide radicals were found the most reactive species of the selected antibiotics. Complete degradation of selected antibiotics was achieved in 90 min with 1.5 g/L of 10% Cu2O-TiO2 nanotubes with initial antibiotic concentration (100 μg/mL) at neutral pH of water matrix. The photocatalyst showed high chemical stability and reusability up to five consecutive cycles. Zeta potential studies confirms the high stability and activity of 10% C-TAC (Cuprous oxide doped Titanium dioxide nanotubes for Applied Catalysis) in the tested pH conditions. Photoluminescence and Electrochemical Impedance Spectroscopy data speculates that 10% C-TAC photocatalyst have efficient photoexcitation in the visible light for photodegradation of antibiotics samples. Inhibitory concentration (IC50) interpretation from the toxicity analysis of native antibiotics concluded that ciprofloxacin was the most toxic antibiotic among the selected antibiotics. Cytotoxicity percentage of transformed products showed r: -0.985, p: 0.01 (negative correlation) with the degradation percentage revealing the efficient degradation of selected antibiotics with no toxic by-products.

Chitosan-Based Biomaterials for Hemostatic Applications: A Review of Recent Advances

Hemorrhage is a detrimental event present in traumatic injury, surgery, and disorders of bleeding that can become life-threatening if not properly managed. Moreover, uncontrolled bleeding can complicate surgical interventions, altering the outcome of surgical procedures. Therefore, to reduce the risk of complications and decrease the risk of morbidity and mortality associated with hemorrhage, it is necessary to use an effective hemostatic agent that ensures the immediate control of bleeding. In recent years, there have been increasingly rapid advances in developing a novel generation of biomaterials with hemostatic properties. Nowadays, a wide array of topical hemostatic agents is available, including chitosan-based biomaterials that have shown outstanding properties such as antibacterial, antifungal, hemostatic, and analgesic activity in addition to their biocompatibility, biodegradability, and wound-healing effects. This review provides an analysis of chitosan-based hemostatic biomaterials and discusses the progress made in their performance, mechanism of action, efficacy, cost, and safety in recent years.

The Development of Alginate/Ag NPs/Caffeic Acid Composite Membranes as Adsorbents for Water Purification

Since the water pollution problem still affects the environmental system and human health, the need to develop innovative membranes has become imperious. Lately, researchers have focused on developing novel materials to help diminish the contamination problem. The aim of present research was to obtain innovative adsorbent composite membranes based on a biodegradable polymer, alginate, to remove toxic pollutants. Of all pollutants, lead was chosen due to its high toxicity. The composite membranes were successfully obtained through a direct casting method. The silver nanoparticles (Ag NPs) and caffeic acid (CA) from the composite membranes were kept at low concentrations, which proved enough to bestow antimicrobial activity to the alginate membrane. The obtained composite membranes were characterised by Fourier transform infrared spectroscopy and microscopy (FTIR), scanning electron microscopy (SEM), and thermogravimetric analysis (TG-DSC). Swelling behaviour, lead ion (Pb²⁺) removal capacity, regeneration and reusability were also determined. Further, the antimicrobial activity was tested against selected pathogenic strains (S. aureus, E. faecalis sp., P. aeruginosa, E. coli and C. albicans). The presence of Ag NPs and CA improves the antimicrobial activity of the newly developed membranes. Overall, the composite membranes are suitable for complex water treatment (removal of heavy metal ions and antimicrobial treatment).

Pb(II) Uptake from Polluted Irrigation Water Using Anatase TiO2 Nanoadsorbent

The adsorption characteristics of titanium dioxide nanoparticles (nano-TiO₂) for the removal of Pb(II) from irrigation water were investigated in this work. To accomplish this, several adsorption factors, such as contact time and pH, were tested to assess adsorption efficiencies and mechanisms. Before and after the adsorption experiments, commercial nano-TiO₂ was studied using X-ray diffraction (XRD), scanning and transmission electron microscopy (SEM and TEM), energy dispersive spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS). The outcomes showed that anatase nano-TiO₂ was remarkably efficient in cleaning Pb(II) from water, with a removal efficiency of more than 99% after only one hour of contact time at a pH of 6.5. Adsorption isotherms and kinetic adsorption data matched the Langmuir and Sips models quite well, showing that the adsorption process occurred at homogenous sites on the surface of nano-TiO₂ by forming a Pb(II) adsorbate monolayer. The XRD and TEM analysis of nano-TiO₂ following the adsorption procedure revealed a non-affected single phase (anatase) with crystallite sizes of 9.9 nm and particle sizes of 22.46 nm, respectively. According to the XPS data and analyzed adsorption data, Pb ions accumulated on the surface of nano-TiO₂ through a three-step mechanism involving ion exchange and hydrogen bonding mechanisms. Overall, the findings indicate that nano-TiO₂ has the potential to be used as an effective and long-lasting mesoporous adsorbent in the treatment and cleaning of Pb(II) from water bodies.

Role of polymer template in crystal structure and photoactivity of Cu-TiO2 heterojunction nanostructures towards environmental remediation

Exploring porous heterojunction nanomaterials as a photocatalyst for water depollution strategies towards environmental restoration is exceedingly difficult in the perspective of sustainable chemistry. Herein, we first report a porous Cu-TiO₂ (TC40) heterojunction by using microphase separation of a novel penta-block copolymer (PLGA-PEO-PPO-PEO-PLGA) as a template through an evaporation induced self-assembly (EISA) method having nanorod-like particle shape. Furthermore, three types of photocatalysts were made with or without template polymer to clarify the function of that template precursor on the surface and morphology, as well as which variables are the most critical for a photocatalyst. TC40 heterojunction nanomaterial displayed high BET surface area along with lower band gap value viz.2.98 eV compare the other and all of these features make it a robust photocatalyst for wastewater treatment. In order to improve water quality, we have carried out experiments on the photodegradation of methyl Orange (MO), highly toxic pollutants that cause health hazards and bioaccumulate in the environment. Our catalyst, TC40 exhibits the 100% photocatalytic efficiency towards MO dye degradation in 40 and 360 min at a rate constant of 0.104 ± 0.007 min^-1 and 0.440 ± 0.03 h^-1 under UV + Vis and visible light irradiation respectively.

Application of Box-Behnken Design to Optimize Phosphate Adsorption Conditions from Water onto Novel Adsorbent CS-ZL/ZrO/Fe3O4: Characterization, Equilibrium, Isotherm, Kinetic, and Desorption Studies

Phosphate (PO43-) is an essential nutrient in agriculture; however, it is hazardous to the environment if discharged in excess as in wastewater discharge and runoff from agriculture. Moreover, the stability of chitosan under acidic conditions remains a concern. To address these problems, CS-ZL/ZrO/Fe3O4 was synthesized using a crosslinking method as a novel adsorbent for the removal of phosphate (PO43-) from water and to increase the stability of chitosan. The response surface methodology (RSM) with a Box-Behnken design (BBD)-based analysis of variance (ANOVA) was implemented. The ANOVA results clearly showed that the adsorption of PO43- onto CS-ZL/ZrO/Fe3O4 was significant (p ≤ 0.05), with good mechanical stability. pH, dosage, and time were the three most important factors for the removal of PO43-. Freundlich isotherm and pseudo-second-order kinetic models generated the best equivalents for PO43- adsorption. The presence of coexisting ions for PO43- removal was also studied. The results indicated no significant effect on PO43- removal (p ≤ 0.05). After adsorption, PO43- was easily released by 1 M NaOH, reaching 95.77% and exhibiting a good capability over three cycles. Thus, this concept is effective for increasing the stability of chitosan and is an alternative adsorbent for the removal of PO43- from water.

Recent Advances in Carbon Nitride-Based S-scheme Photocatalysts for Solar Energy Conversion

Energy shortages are a major challenge to the sustainable development of human society, and photocatalytic solar energy conversion is a potential way to alleviate energy problems. As a two-dimensional organic polymer semiconductor, carbon nitride is considered to be the most promising photocatalyst due to its stable properties, low cost, and suitable band structure. Unfortunately, pristine carbon nitride has low spectral utilization, easy recombination of electron holes, and insufficient hole oxidation ability. The S-scheme strategy has developed in recent years, providing a new perspective for effectively solving the above problems of carbon nitride. Therefore, this review summarizes the latest progress in enhancing the photocatalytic performance of carbon nitride via the S-scheme strategy, including the design principles, preparation methods, characterization techniques, and photocatalytic mechanisms of the carbon nitride-based S-scheme photocatalyst. In addition, the latest research progress of the S-scheme strategy based on carbon nitride in photocatalytic H₂ evolution and CO₂ reduction is also reviewed. Finally, some concluding remarks and perspectives on the challenges and opportunities for exploring advanced nitride-based S-scheme photocatalysts are presented. This review brings the research of carbon nitride-based S-scheme strategy to the forefront and is expected to guide the development of the next-generation carbon nitride-based S-scheme photocatalysts for efficient energy conversion.

Synergistic Antimicrobial Activity of Magnetite and Vancomycin-Loaded Mesoporous Silica Embedded in Alginate Films

The aim of the present study was to obtain a hydrogel-based film as a carrier for the sustained and controlled release of vancomycin, an antibiotic commonly used in various types of infections. Considering the high-water solubility of vancomycin (>50 mg/mL) and the aqueous medium underlying the exudates, a prolonged release of vancomycin from an MCM-41 carrier was sought. The present work focused on the synthesis of malic acid coated magnetite (Fe3O4/malic) by co-precipitation, synthesis of MCM-41 by a sol-gel method and loading of MCM-41 with vancomycin, and their use in alginate films for wound dressing. The nanoparticles obtained were physically mixed and embedded in the alginate gel. Prior to incorporation, the nanoparticles were characterized by XRD, FT-IR and FT-Raman spectroscopy, TGA-DSC and DLS. The films were prepared by a simple casting method and were further cross-linked and examined for possible heterogeneities by means of FT-IR microscopy and SEM. The degree of swelling and the water vapor transmission rate were determined, considering their potential use as wound dressings. The obtained films show morpho-structural homogeneity, sustained release over 48 h and a strong synergistic enhancement of the antimicrobial activity as a consequence of the hybrid nature of these films. The antimicrobial efficacy was tested against S. aureus, two strains of E. faecalis (including vancomycin-resistant Enterococcus, VRE) and C. albicans. The incorporation of magnetite was also considered as an external triggering component in case the films were used as a magneto-responsive smart dressing to stimulate vancomycin diffusion.

Antimicrobial particles based on Cu2ZnSnS4 monograins

In this research, Cu₂ZnSnS₄ (CZTS) particles were successfully fabricated via the molten salt approach from the copper, zinc and tin sulphides as raw precursors. SEM analysis revealed that CZTS particles are tetragonal-shaped with sharp edges, smooth flat plane morphology, and crystal size varying from 10.8 to 28.7 µm. The phase and crystalline structure of synthesized powders were investigated using XRD analysis, which confirms the presence of a tetragonal crystal structure kesterite phase. The chemical composition of CZTS particles was evaluated by EDX spectroscopy, which identified the nearly stoichiometric composition with an averaged formula of Cu_1.88Zn_1.04SnS_3.97. The TG/DTA-MS and ICP-OES analysis showed the possible decomposition pathways and predicted their degradation rate in aqueous solutions. The CZTS particles possessed highly effective concentration and time-dependent antimicrobial properties against medically relevant bacteria and yeast strains. The CZTS particles (1 g L^-1) exhibited over 95.7 ± 1.9% killing efficiency towards M. luteus. In contrast, higher dosages (3.5 and 5 g L^-1) led to its complete inactivation and reduced the P. aeruginosa cell viability to 43.2 ± 3.2% and 4.1 ± 1.1%, respectively. Moreover, the CZTS particles (0.5 g L^-1) are responsible for causing 54.8 ± 1.8% of C. krusei and 89.7 ± 2.1% of C. parapsilosis yeasts death within the 24 h of exposure, which expanded to almost 100% when yeasts were treated with two times higher CZTS concentration (1.0 g L^-1). The mechanism of action has been proposed and evidenced by monitoring the 2',7'-dichlorofluorescein (DCF) fluorescence, which revealed that the overproduction of reactive oxygen species (ROS) is responsible for microorganism death.

Antibacterial Activity of Solvothermal Obtained ZnO Nanoparticles with Different Morphology and Photocatalytic Activity against a Dye Mixture: Methylene Blue, Rhodamine B and Methyl Orange

In this paper, we report the synthesis of ZnO nanoparticles (NPs) by forced solvolysis of Zn(CH3COO)2·2H2O in alcohols with a different number of –OH groups. We study the influence of alcohol type (n-butanol, ethylene glycol and glycerin) on the size, morphology, and properties of the obtained ZnO NPs. The smallest polyhedral ZnO NPs (<30 nm) were obtained in n-butanol, while in ethylene glycol the NPs measured on average 44 nm and were rounded. Polycrystalline particles of 120 nm were obtained in glycerin only after water refluxing. In addition, here, we report the photocatalytic activity, against a dye mixture, of three model pollutants: methyl orange (MO), methylene blue (MB), and rhodamine B (RhB), a model closer to real situations where water is polluted with many chemicals. All samples exhibited good photocatalytic activity against the dye mixture, with degradation efficiency reaching 99.99%. The sample with smallest nanoparticles maintained a high efficiency >90%, over five catalytic cycles. Antibacterial tests were conducted against Gram-negative strains Salmonella enterica serovar Typhimurium, Pseudomonas aeruginosa, and Escherichia coli, and Gram-positive strains Enterococcus faecalis, Bacillus subtilis, Staphylococcus aureus, and Bacillus cereus. The ZnO samples presented strong inhibition of planktonic growth for all tested strains, indicating that they can be used for antibacterial applications, such as water purification.

Artificial intelligence-based optimization for chitosan nanoparticles biosynthesis, characterization and in‑vitro assessment of its anti-biofilm potentiality

Chitosan nanoparticles (CNPs) are promising biopolymeric nanoparticles with excellent physicochemical, antimicrobial, and biological properties. CNPs have a wide range of applications due to their unique characteristics, including plant growth promotion and protection, drug delivery, antimicrobials, and encapsulation. The current study describes an alternative, biologically-based strategy for CNPs biosynthesis using Olea europaea leaves extract. Face centered central composite design (FCCCD), with 50 experiments was used for optimization of CNPs biosynthesis. The artificial neural network (ANN) was employed for analyzing, validating, and predicting CNPs biosynthesis using Olea europaea leaves extract. Using the desirability function, the optimum conditions for maximum CNPs biosynthesis were determined theoretically and verified experimentally. The highest experimental yield of CNPs (21.15 mg CNPs/mL) was obtained using chitosan solution of 1%, leaves extract solution of 100%, initial pH 4.47, and incubation time of 60 min at 53.83°C. The SEM and TEM images revealed that CNPs had a spherical form and varied in size between 6.91 and 11.14 nm. X-ray diffraction demonstrates the crystalline nature of CNPs. The surface of the CNPs is positively charged, having a Zeta potential of 33.1 mV. FTIR analysis revealed various functional groups including C-H, C-O, CONH2, NH2, C-OH and C-O-C. The thermogravimetric investigation indicated that CNPs are thermally stable. The CNPs were able to suppress biofilm formation by P. aeruginosa, S. aureus and C. albicans at concentrations ranging from 10 to 1500 µg/mL in a dose-dependent manner. Inhibition of biofilm formation was associated with suppression of metabolic activity, protein/exopolysaccharide moieties, and hydrophobicity of biofilm encased cells (r ˃ 0.9, P = 0.00). Due to their small size, in the range of 6.91 to 11.14 nm, CNPs produced using Olea europaea leaves extract are promising for applications in the medical and pharmaceutical industries, in addition to their potential application in controlling multidrug-resistant microorganisms, especially those associated with post COVID-19 pneumonia in immunosuppressed patients.

Synthesis and Characterization of SPIONs Encapsulating Polydopamine Nanoparticles and Their Test for Aqueous Cu2+ Ion Removal

The removal of pollutants, such as heavy metals, aromatic compounds, dyes, pesticides and pharmaceuticals, from water is still an open challenge. Many methods have been developed and exploited for the purification of water from contaminants, including photocatalytic degradation, biological treatment, adsorption and chemical precipitation. Absorption-based techniques are still considered among the most efficient and commonly used approaches thanks to their operational simplicity. In recent years, polydopamine-coated magnetic nanoparticles have emerged for the uptake of heavy metals in water treatment, since they combine specific affinity towards pollutants and magnetic separation capacity. In this context, this work focuses on the synthesis of polydopamine (PDA)-coated Super Paramagnetic Iron Oxide Nanoparticles (PDA@SPIONs) as adsorbents for Cu²⁺ ions, designed to serve as functional nanostructures for the removal of Cu²⁺ from water by applying a magnetic field. The synthetic parameters, including the amount of SPIONs and PDA, were thoroughly investigated to define their effects on the nanostructure features and properties. Subsequently, the ability of the magnetic nanostructures to bind metal ions was assessed on Cu²⁺-containing solutions. A systematic investigation of the prepared functional nanostructures was carried out by means of complementary spectroscopic, morphological and magnetic techniques. Inductively coupled plasma atomic emission spectroscopy (ICP-AES) measurements were performed in order to estimate the Cu²⁺ binding ability. The overall results indicate that these nanostructures hold great promise for future bioremediation applications.

Facile synthesis and characterization of magnesium and manganese mixed oxides for the efficient removal of tartrazine dye from aqueous media

Nanomaterials are the most effective class of substances for use as adsorbents in wastewater treatment. Hence, the current study involves the facile and low-cost synthesis of MgMn₂O₄/Mn₂O₃ and MgMn₂O₄/Mn₂O₃/Mg₆MnO₈ as novel nanostructures from mixed solutions of Mg(ii) and Mn(ii) ions using the Pechini sol-gel method. After that, the remaining powder was calcined at 500, 700, and 900 °C for 3 h; the products were designated as G500, G700, and G900, respectively. The G500 sample consists of MgMn₂O₄ and Mn₂O₃, while the G700 and G900 samples consist of MgMn₂O₄, Mg₆MnO₈, and Mn₂O₃. The synthesized nanostructures were characterized using several tools, such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and N₂ adsorption/desorption analysis. The average crystallite size of the G500, G700, and G900 samples is 210.53, 95.27, and 83.43 nm, respectively. The SEM images showed that the G500 sample consists of square and rectangular bars with an average diameter of 3.18 μm. Also, the G700 and G900 samples consist of hexagonal, polyhedral, and irregular shapes with an average diameter of 1.12 and 0.54 μm, respectively. The synthesized nanostructures were further utilized as adsorbents for the efficient removal of tartrazine dye from aqueous media. The experimental data showed a good fit with the Langmuir isotherm and pseudo-first-order model. The maximum adsorption capacities of the G500, G700, and G900 adsorbents toward tartrazine dye are 328.95, 359.71, and 395.26 mg g^-1, respectively.

Influence of the Alcohols on the ZnO Synthesis and Its Properties: The Photocatalytic and Antimicrobial Activities

Zinc oxide (ZnO) nanomaterials are used in various health-related applications, from antimicrobial textiles to wound dressing composites and from sunscreens to antimicrobial packaging. Purity, surface defects, size, and morphology of the nanoparticles are the main factors that influence the antimicrobial properties. In this study, we are comparing the properties of the ZnO nanoparticles obtained by solvolysis using a series of alcohols: primary from methanol to 1-hexanol, secondary (2-propanol and 2-butanol), and tertiary (tert-butanol). While the synthesis of ZnO nanoparticles is successfully accomplished in all primary alcohols, the use of secondary or tertiary alcohols does not lead to ZnO as final product, underlining the importance of the used solvent. The shape of the obtained nanoparticles depends on the alcohol used, from quasi-spherical to rods, and consequently, different properties are reported, including photocatalytic and antimicrobial activities. In the photocatalytic study, the ZnO obtained in 1-butanol exhibited the best performance against methylene blue (MB) dye solution, attaining a degradation efficiency of 98.24%. The comparative study among a series of usual model dyes revealed that triarylmethane dyes are less susceptible to photo-degradation. The obtained ZnO nanoparticles present a strong antimicrobial activity on a broad range of microorganisms (bacterial and fungal strains), the size and shape being the important factors. This permits further tailoring for use in medical applications.