Flow and Particle Modelling of Dry Powder Inhalers: Methodologies, Recent Development and Emerging Applications

Dry Powder Formulations for Inhalation Require a Smaller Aerodynamic Diameter for Usage at High Altitude

BACKGROUND

High Altitude Pulmonary Edema (HAPE) seriously threatens the health of people at high altitudes. There are drug treatments for HAPE, and dry powder formulations (DPFs) represent a rapid and accessible delivery vehicle for these drugs. However, there are presently no reports on the inhalability of DPFs in low-pressure environments. Given the reduced atmospheric pressure typical at high altitudes, conventional DPFs might not be suitable for inhalation. Therefore, it is necessary to elucidate the deposition behaviors of dry powder in the respiratory tract at low pressure, as well as to improve their pulmonary deposition efficiency via adjustments to their formulation and design.

METHODS

The effect of air pressure, inspiratory velocity, and particle properties (such as size, density, and aerodynamic diameter) on pulmonary deposition of DPFs was calculated by a computational fluid dynamics (CFD)-coupled discrete phase model. DPFs of various aerodynamic diameters were prepared by spray drying, and the inhalability of these DPFs in a low-pressure environment was evaluated in mice. Finally, a mouse model of HAPE was established, and the treatment of HAPE by nifedipine-loaded DPFs with small aerodynamic diameter was validated.

RESULTS

CFD results showed that low pressure decreased the deposition of DPFs in the lungs. At 0.5 standard atmosphere, DPFs with aerodynamic diameter of ∼2.0 μm could not enter the lower respiratory tract; however, a decrease in the physical diameter, density, and, consequently, the aerodynamic diameter of the DPFs was able to enhance pulmonary deposition of these powders. To validate the CFD results, three kinds of dry powder with aerodynamic diameters of 0.66, 0.98, and 2.00 μm were prepared by spray drying. Powders with smaller aerodynamic diameter could be inhaled into the lungs of mice more effectively, and, consequently could ameliorate the progression of HAPE more effectively than conventional powders. These results were consistent with the CFD results.

CONCLUSIONS

Low atmospheric pressure can prevent the pulmonary deposition of DPFs at high altitudes. Compared with conventional DPFs, powders with smaller aerodynamic diameter can be effectively inhaled at these pressures and thus might be more suitable for the treatment the HAPE.

Dry Powder Inhaler with the technical and practical obstacles, and forthcoming platform strategies

A Dry Powder Inhaler (DPI) is a technique as well as a device used to inhale formulation which is in the form of dry powder, and is inhaled through the nose or mouth. It was developed for the purpose of treating conditions like chronic obstructive pulmonary disease (COPD), Asthma, and even cystic fibrosis etc. The aim of the review is to discuss the different methods of preparation of dry powders along with the characterization of DPI. Here we present the outline of different methods like supercritical fluid extraction (SCF), spray drying, and milling. The review focussed on various devices including single and multi-dose devices used in the DPI. It also highlights on recent advances in the DPI including nano particulate system, siRNA-based medication, liposomes, and pro-liposomes based delivery. In COVID-19 silver nanoparticles-based DPIs provide very prominent results in the infected lungs. Moreover, this review states that the AI-based DPI development provides and improvement in the bioavailability and effectiveness of the drug along with the role of artificial neural networks (ANN). The study also showed that nasally administered drugs (nose to brain) can easily cross the blood-brain barrier (BBB) and enter the central nervous system (CNS) through the olfactory and trigeminal pathway which provides effective CNS concentrations at lower dosage. It is suggested that DPIs not only target respiratory complications but also treat CNS complications too. This review provides support and guides the researcher in the recent development and evaluation of DPI.

Numerical Modeling of Particle Dynamics Inside a Dry Powder Inhaler

The development of novel dry powders for dry powder inhalers (DPIs) requires the in vitro assessment of DPI aerodynamic performance. As a potential complementary method, in silico numerical simulations can provide additional information about the mechanisms that guide the particles and their behavior inside DPIs. The aim of this study was to apply computational fluid dynamics (CFDs) coupled with a discrete phase model (DPM) to describe the forces and particle trajectories inside the RS01^® as a model DPI device. The methodology included standard fluid flow equations but also additional equations for the particle sticking mechanism, as well as particle behavior after contacting the DPI wall surface, including the particle detachment process. The results show that the coefficient of restitution between the particle and the impact surface does not have a high impact on the results, meaning that all tested combinations gave similar output efficiencies and particle behaviors. No sliding or rolling mechanisms were observed for the particle detachment process, meaning that simple bouncing off or deposition particle behavior is present inside DPIs. The developed methodology can serve as a basis for the additional understanding of the particles' behavior inside DPIs, which is not possible using only in vitro experiments; this implies the possibility of increasing the efficiency of DPIs.

Recent developments in the computational simulation of dry powder inhalers

This article reviews recent developments in computational modeling of dry powder inhalers (DPIs). DPIs deliver drug formulations (sometimes blended with larger carrier particles) to a patient's lungs via inhalation. Inhaler design is complicated by the need for maximum aerosolization efficiency, which is favored by high levels of turbulence near the mouthpiece, with low extrathoracic depositional loss, which requires low turbulence levels near the mouth-throat region. In this article, we review the physical processes contributing to aerosolization and subsequent dispersion and deposition. We assess the performance characteristics of DPIs using existing simulation techniques and offer a perspective on how such simulations can be improved to capture the physical processes occurring over a wide range of length- and timescales more efficiently.

Focusing on powder processing in dry powder inhalation product development, manufacturing and performance

Dry powder inhalers (DPI) are well established products for the delivery of actives via the pulmonary route. Various DPI products are marketed or developed for the treatment of local lung diseases such as chronic obstructive pulmonary disease (COPD), asthma or cystic fibrosis as well as systemic diseases targeted through inhaled delivery (i.e. Diabetes Mellitus). One of the key prerequisites of DPI formulations is that the aerodynamic size of the drug particles needs to be below 5 µm to enter deeply into the respiratory tract. These inherently cohesive inhalable size particles are either formulated as adhesive mixture with coarse carrier particles like lactose called carrier-based DPI or are formulated as free-flowing carrier-free particles (e.g. soft agglomerates, large hollow particles). In either case, it is common practice that drug and/or excipient particles of DPI formulations are obtained by processing API and API/excipients. The DPI manufacturing process heavily involves several particle and powder technologies such as micronization of the API, dry blending, powder filling and other particle engineering processes such as spray drying, crystallization etc. In this context, it is essential to thoroughly understand the impact of powder/particle properties and processing on the quality and performance of the DPI formulations. This will enable prediction of the processability of the DPI formulations and controlling the manufacturing process so that meticulously designed formulations are able to be finally developed as the finished DPI dosage form. This article is intended to provide a concise account of various aspects of DPI powder processing, including the process understanding and material properties that are important to achieve the desired DPI product quality. Various endeavors of model informed formulation/process design and development for DPI powder and PAT enabled process monitoring and control are also discussed.

Combining experimental and computational techniques to understand and improve dry powder inhalers

INTRODUCTION

: Dry Powder Inhalers (DPIs) continue to be developed to deliver an expanding range of drugs to treat an ever-increasing range of medical conditions; with each drug and device combination needing a specifically designed inhaler. Fast regulatory approval is essential to be first to market, ensuring commercial profitability.

AREAS COVERED

: In vitro deposition, particle image velocimetry, and computational modelling using the physiological geometry and representative anatomy can be combined to give complementary information to determine the suitability of a proposed inhaler design and to optimise its formulation performance. In combination they allow the entire range of questions to be addressed cost-effectively and rapidly.

EXPERT OPINION

: Experimental techniques and computational methods are improving rapidly, but each needs a skilled user to maximize results obtained from these techniques. Multidisciplinary teams are therefore key to making optimal use of these methods and such qualified teams can provide enormous benefits to pharmaceutical companies to improve device efficacy and thus time to market. There is already a move to integrate the benefits of Industry 4.0 into inhaler design and usage, a trend that will accelerate.

Effects of dose loading conditions and device geometry on the transport and aerosolization in dry powder inhalers: A simulation study

The transport and aerosolization of particles are studied in several different dry powder inhaler geometries via Computational Fluid Dynamics-Discrete Element Method (CFD-DEM) simulations. These simulations combine Large Eddy Simulation of gas with Discrete Element Model simulation of all the carrier particles and a representative subset of the active pharmaceutical ingredient (API) particles. The purpose of the study is to probe the dominant mechanism leading to the release of the API particles and to demonstrate the value of the CFD-DEM simulations where one tracks the motion of all the carrier and API particles. Simulations are performed at different inhalation rates and initial dose loading conditions for the screen-haler geometry, a simple cylindrical tube inhaler, and five different geometry modifications that took the form of bumpy walls and baffles. These geometry modifications alter the residence time of the powder sample in the inhaler, pressure drop across the inhaler, the severity of gas-carrier interactions, and the number of collisions experienced by the carrier particles, all of which are quantified. The quality of aerosolization is found to correlate with the average air-carrier slip velocity, while collisions played only a secondary role. Some geometry modifications improved aerosolization quality with very little increase in the pressure drop across the device.

Carrier particle emission and dispersion in transient CFD-DEM simulations of a capsule-based DPI

The dispersion of carrier-based formulations in capsule-based dry powder inhalers depends on several factors, including the patient's inhalation profile and the motion of capsule within the device. In the present study, coupled computational fluid dynamics and discrete element method simulations of a polydisperse cohesive lactose carrier in an Aerolizer® inhaler were conducted at a constant flow rate of 100 L/min and considering an inhalation profile of asthmatic children between 5 and 17 years approximated from literature data. In relevant high-speed photography experiments, it was observed that the powder was distributed to both capsule ends before being ejected from the capsule. Several methods of ensuring similar behavior in the simulations were presented. Both the constant flow rate simulation and the profile simulations showed a high powder retention in the capsule (7.37-19.00%). Although the inhaler retention was negligible in the constant flow rate simulation due to consistently high air velocities in the device, it reached values of around 7% in most of the profile simulations. In all simulations, some of the carrier powder was ejected from the capsule as particle clusters. These clusters were larger in the profile simulation than in the constant flow rate simulation. Of the powder discharged from the capsule, a high percentage was bound in clusters in the profile simulation in the beginning and at the end of the inhalation profile while no more than 10% of the powder ejected from the capsule in the 100 L/min constant flow rate simulation were in clusters at any time. The powder emission from the capsule was studied, indicating a strong dependency of the powder mass flow from the capsule on the angular capsule position. When the capsule holes face the inhaler's air inlets, the air flow into the capsule restricts the powder discharge. The presented results provide a detailed view of some aspects of the powder flow and dispersion of a cohesive carrier in a capsule-based inhaler device. Furthermore, the importance of considering inhalation profiles in addition to conventional constant flow rate simulations was confirmed.

Comparative Assessment of In Vitro and In Silico Methods for Aerodynamic Characterization of Powders for Inhalation

In vitro assessment of dry powders for inhalation (DPIs) aerodynamic performance is an inevitable test in DPI development. However, contemporary trends in drug development also implicate the use of in silico methods, e.g., computational fluid dynamics (CFD) coupled with discrete phase modeling (DPM). The aim of this study was to compare the designed CFD-DPM outcomes with the results of three in vitro methods for aerodynamic assessment of solid lipid microparticle DPIs. The model was able to simulate particle-to-wall sticking and estimate fractions of particles that stick or bounce off the inhaler's wall; however, we observed notable differences between the in silico and in vitro results. The predicted emitted fractions (EFs) were comparable to the in vitro determined EFs, whereas the predicted fine particle fractions (FPFs) were generally lower than the corresponding in vitro values. In addition, CFD-DPM predicted higher mass median aerodynamic diameter (MMAD) in comparison to the in vitro values. The outcomes of different in vitro methods also diverged, implying that these methods are not interchangeable. Overall, our results support the utility of CFD-DPM in the DPI development, but highlight the need for additional improvements in these models to capture all the key processes influencing aerodynamic performance of specific DPIs.