A Review on Properties and Application of Bio-Based Poly(Butylene Succinate)

Enzymatic Degradation Behavior of Self-Degradable Lipase-Embedded Aliphatic and Aromatic Polyesters and Their Blends

Over the past decade, the preparation of novel materials by enzyme-embedding into biopolyesters has been proposed as a straightforward method to produce self-degrading polymers. This paper reports the preparation and enzymatic degradation of extruded self-degradable films of three different biopolyesters: poly(lactic acid) (PLA), poly(butylene adipate-co-terephthalate) (PBAT), and poly(butylene succinate) (PBS), as well as three binary/ternary blends. Candida antarctica lipase B (CalB) has been employed for the enzyme-embedding procedure, and to the best of our knowledge, the use of this approach in biopolyester blends has not been reported before. The three homopolymers exhibited differentiated degradation and suggested a preferential attack of CalB on PBS films over PBAT and PLA. Moreover, the self-degradable films obtained from the blends showed slow degradation, probably due to the higher content in PLA and PBAT. These observations pave the way for exploring enzymes capable of degrading all blend components or an enzymatic mixture for blend degradation.

Poly(butylene oxalate-co-terephthalate): A PBAT-like but rapid hydrolytic degradation plastic

Concerns over worldwide plastic pollution have led to the development of biodegradable polyester materials with excellent physical and chemical properties through the copolymerization of poly(butylene oxalate) (PBOx). As a result, poly(butylene oxalate-co-terephthalate)s (PBOTs) with varying compositions, were prepared by incorporating aromatic units. Studies have indicated that PBOT-47 (with a 47% molar terephthalate), exhibits exceptional mechanical properties. With an elongation at break of 1160% and a tensile strength that remains above 30 MPa, similar to or even better than those of the commercial biodegradable plastic poly(butylene adipate-co-terephthalate) PBAT-47 (47% molar terephthalate). Moreover, the permeability coefficients of PBAT-47 for H2O, CO2 and O2 were 5.8, 50.6 and 5.6 times higher than that of PBOT-47, revealing the superior barrier properties of PBOT. Through experimental research and theoretical simulation, the mechanism of the copolymer hydrolysis was elucidated. The readily hydrolytic nature of the oxalate unit endows it with the capacity for rapid degradation, possessing the potential to be a short-term degradable material with physical properties similar to PBAT.

Recent advancements in bio-based dielectric and piezoelectric polymers and their biomedical applications

The advent of polymer-based dielectrics marked a significant breakthrough in dielectric materials. However, despite their many advantages, they pose serious environmental threats. Therefore, in recent years, there has been growing interest in bio-based polymers as a sustainable alternative to traditional petroleum-based polymers. Their renewable nature and reduced environmental impact can fulfil the rising demand for eco-friendly substitutes. Beyond their ecological benefits, bio-based polymers also possess distinctive electrical properties that make them extremely attractive in a variety of applications. Considering these, herein, we present recent advancements in bio-based dielectric polymers and nanocomposites. First, the fundamental concepts of dielectric and polymer-based dielectric materials are covered. Then, we will delve into the discussion of recent advancements in the dielectric properties and thermal stability of bio-based polymers, including polylactic acid, polyhydroxyalkanoates, polybutylene succinate, starch, cellulose, chitosan, chitins, and alginates, and their nanocomposites. Other novel bio-based dielectric polymers and their distinct dielectric characteristics have also been pointed out. In an additional section, the piezoelectric properties of these polymers and their recent biomedical applications have been highlighted and discussed thoroughly. In conclusion, this paper thoroughly discusses the recent advances in bio-based dielectric polymers and their potential to revolutionize the biomedical industry while cultivating a more sustainable and greener future.

Mechanical and Physical Changes in Bio-Polybutylene-Succinate Induced by UVC Ray Photodegradation

Bio-polybutylene succinate (PBS) is a biodegradable polymer obtained from renewable feedstock having physical-mechanical properties like traditional low-density polyethylene (LDPE). PBS is employed by many manufacturing sectors, from biomedical to agri-food and cosmetics. Although some studies have already evaluated the resistance of PBS to photodegradation caused by natural outdoor solar exposure (UVA-UVB), a systematic study on the resistance to degradation caused by exposure to UVC rays, which is the subject of this study, has not yet been carried out. PBS was exposed to UVC either neat or filled with 2% carbon black (CB). Mechanical and physical characterization (tensile, hardness, calorimetry, contact angle, morphology, and surface roughness analyses) indicates that the bulk and surface properties of the polymer matrix changes after exposure to UVC radiations, due to a severe degradation. However, the presence of carbon black compensates for the degradation phenomenon. Because UVC rays are used for the sterilization process, necessary in applications such as biomedical, cosmetic, pharmaceutical, food, and other products, a comparison of the protocol used in this paper with the literature's data has been reported and discussed.

Macroalgae Bioplastics: A Sustainable Shift to Mitigate the Ecological Impact of Petroleum-Based Plastics

The surge in global utilization of petroleum-based plastics, which notably heightened during the COVID-19 pandemic, has substantially increased its harm to ecosystems. Considering the escalating environmental impact, a pivotal shift towards bioplastics usage is imperative. Exploring and implementing bioplastics as a viable alternative could mitigate the ecological burden posed by traditional plastics. Macroalgae is a potential feedstock for the production of bioplastics due to its abundance, fast growth, and high cellulose and sugar content. Researchers have recently explored various methods for extracting and converting macroalgae into bioplastic. Some of the key challenges in the production of macroalgae bioplastics are the high costs of large-scale production and the need to optimize the extraction and conversion processes to obtain high-quality bioplastics. However, the potential benefits of using macroalgae for bioplastic production include reducing plastic waste and greenhouse gas emissions, using healthier materials in various life practices, and developing a promising area for future research and development. Also, bioplastic provides job opportunities in free enterprise and contributes to various applications such as packaging, medical devices, electronics, textiles, and cosmetics. The presented review aims to discuss the problem of petroleum-based plastic, bioplastic extraction from macroalgae, bioplastic properties, biodegradability, its various applications, and its production challenges.

Recyclable and (Bio)degradable Polyesters in a Circular Plastics Economy

Polyesters carrying polar main-chain ester linkages exhibit distinct material properties for diverse applications and thus play an important role in today's plastics economy. It is anticipated that they will play an even greater role in tomorrow's circular plastics economy that focuses on sustainability, thanks to the abundant availability of their biosourced building blocks and the presence of the main-chain ester bonds that can be chemically or biologically cleaved on demand by multiple methods and thus bring about more desired end-of-life plastic waste management options. Because of this potential and promise, there have been intense research activities directed at addressing recycling, upcycling or biodegradation of existing legacy polyesters, designing their biorenewable alternatives, and redesigning future polyesters with intrinsic chemical recyclability and tailored performance that can rival today's commodity plastics that are either petroleum based and/or hard to recycle. This review captures these exciting recent developments and outlines future challenges and opportunities. Case studies on the legacy polyesters, poly(lactic acid), poly(3-hydroxyalkanoate)s, poly(ethylene terephthalate), poly(butylene succinate), and poly(butylene-adipate terephthalate), are presented, and emerging chemically recyclable polyesters are comprehensively reviewed.

Recent advances in microbial and enzymatic engineering for the biodegradation of micro- and nanoplastics

This review examines the escalating issue of plastic pollution, specifically highlighting the detrimental effects on the environment and human health caused by microplastics and nanoplastics. The extensive use of synthetic polymers such as polyethylene (PE), polyethylene terephthalate (PET), and polystyrene (PS) has raised significant environmental concerns because of their long-lasting and non-degradable characteristics. This review delves into the role of enzymatic and microbial strategies in breaking down these polymers, showcasing recent advancements in the field. The intricacies of enzymatic degradation are thoroughly examined, including the effectiveness of enzymes such as PETase and MHETase, as well as the contribution of microbial pathways in breaking down resilient polymers into more benign substances. The paper also discusses the impact of chemical composition on plastic degradation kinetics and emphasizes the need for an approach to managing the environmental impact of synthetic polymers. The review highlights the significance of comprehending the physical characteristics and long-term impacts of micro- and nanoplastics in different ecosystems. Furthermore, it points out the environmental and health consequences of these contaminants, such as their ability to cause cancer and interfere with the endocrine system. The paper emphasizes the need for advanced analytical methods and effective strategies for enzymatic degradation, as well as continued research and development in this area. This review highlights the crucial role of enzymatic and microbial strategies in addressing plastic pollution and proposes methods to create effective and environmentally friendly solutions.

Reproducible Polybutylene Succinate (PBS)-Degrading Artificial Consortia by Introducing the Least Type of PBS-Degrading Strains

Polybutylene succinate (PBS) stands out as a promising biodegradable polymer, drawing attention for its potential as an eco-friendly alternative to traditional plastics due to its biodegradability and reduced environmental impact. In this study, we aimed to enhance PBS degradation by examining artificial consortia composed of bacterial strains. Specifically, Terribacillus sp. JY49, Bacillus sp. JY35, and Bacillus sp. NR4 were assessed for their capabilities and synergistic effects in PBS degradation. When only two types of strains, Bacillus sp. JY35 and Bacillus sp. NR4, were co-cultured as a consortium, a notable increase in degradation activity toward PBS was observed compared to their activities alone. The consortium of Bacillus sp. JY35 and Bacillus sp. NR4 demonstrated a remarkable degradation yield of 76.5% in PBS after 10 days. The degradation of PBS by the consortium was validated and our findings underscore the potential for enhancing PBS degradation and the possibility of fast degradation by forming artificial consortia, leveraging the synergy between strains with limited PBS degradation activity. Furthermore, this study demonstrated that utilizing only two types of strains in the consortium facilitates easy control and provides reproducible results. This approach mitigates the risk of losing activity and reproducibility issues often associated with natural consortia.

Bacteria for Bioplastics: Progress, Applications, and Challenges

Bioplastics are one of the answers that can point society toward a sustainable future. Under this premise, the synthesis of polymers with competitive properties using low-cost starting materials is a highly desired factor in the industry. Also, tackling environmental issues such as nonbiodegradable waste generation, high carbon footprint, and consumption of nonrenewable resources are some of the current concerns worldwide. The scientific community has been placing efforts into the biosynthesis of polymers using bacteria and other microbes. These microorganisms can be convenient reactors to consume food and agricultural wastes and convert them into biopolymers with inherently attractive properties such as biodegradability, biocompatibility, and appreciable mechanical and chemical properties. Such biopolymers can be applied to several fields such as packing, cosmetics, pharmaceutical, medical, biomedical, and agricultural. Thus, intending to elucidate the science of microbes to produce polymers, this review starts with a brief introduction to bioplastics by describing their importance and the methods for their production. The second section dives into the importance of bacteria regarding the biochemical routes for the synthesis of polymers along with their advantages and disadvantages. The third section covers some of the main parameters that influence biopolymers' production. Some of the main applications of biopolymers along with a comparison between the polymers obtained from microorganisms and the petrochemical-based ones are presented. Finally, some discussion about the future aspects and main challenges in this field is provided to elucidate the main issues that should be tackled for the wide application of microorganisms for the preparation of bioplastics.

Ductile Copolyesters Prepared Using Succinic Acid, 1,4-Butanediol, and Bis(2-hydroxyethyl) Terephthalate with Minimizing Generation of Tetrahydrofuran

Poly(1,4-butylene succinate) (PBS) is a promising sustainable and biodegradable synthetic polyester. In this study, we synthesized PBS-based copolyesters by incorporating 5-20 mol% of -O2CC6H4CO2- and -OCH2CH2O- units through the polycondensation of succinic acid (SA) with 1,4-butanediol (BD) and bis(2-hydroxyethyl) terephthalate (BHET). Two different catalysts, H3PO4 and the conventional catalyst (nBuO)4Ti, were used comparatively in the synthesis process. The copolyesters produced using the former were treated with M(2-ethylhexanoate)2 (M = Mg, Zn, Mn) to connect the chains through ionic interactions between M2+ ions and either -CH2OP(O)(OH)O- or (-CH2O)2P(O)O- groups. By incorporating BHET units (i.e., -O2CC6H4CO2- and -OCH2CH2O-), the resulting copolyesters exhibited improved ductile properties with enhanced elongation at break, albeit with reduced tensile strength. The copolyesters prepared with H3PO4/M(2-ethylhexanoate)2 displayed a less random distribution of -O2CC6H4CO2- and -OCH2CH2O- units, leading to a faster crystallization rate, higher Tm value, and higher yield strength compared to those prepared with (nBuO)4Ti using the same amount of BHET. Furthermore, they displayed substantial shear-thinning behavior in their rheological properties due to the presence of long-chain branches of (-CH2O)3P=O units. Unfortunately, the copolyesters prepared with H3PO4/M(2-ethylhexanoate)2, and hence containing M2+, -CH2OP(O)(OH)O-, (-CH2O)2P(O)O- groups, did not exhibit enhanced biodegradability under ambient soil conditions.

Bio-based epoxidized soybean oil branched cardanol ethers as compatibilizers of polybutylene succinate (PBS)/polyglycolic acid (PGA) blends

Blending poly(butylene succinate) (PBS) with another biodegradable polymer, polyglycolic acid (PGA), has been demonstrated to improve the barrier performance of PBS. However, blending these two polymers poses a challenge because of their incompatibility and large difference of their melting temperatures. In this study, we synthesized epoxidized soybean oil branched cardanol ether (ESOn-ECD), a bio-based and environmentally friendly compatibilizer, and used it to enhance the compatibility of PBS/PGA blends. It was demonstrated that the terminal carboxyl/hydroxyl groups of PBS and PGA can react with ESOn-ECD in situ, leading to branching and chain extension of PBS and PGA. The addition of ESO3-ECD to the blend considerably diminished the dispersed phase of PGA. Specifically, in comparison to the PBS/PGA blend without a compatibilizer, the diameter of the PGA phase decreased from 2.04 μm to 0.45 μm after the addition of 0.7 phr of ESO3-ECD, and the boundary between the two phases became difficult to distinguish. Additionally, the mechanical properties of the blends were improved after addition of ESO3-ECD. This research expands the potential applications of these materials and promotes the use of bio-based components in blend formulations.

Biodegradable nanofibrillated microcellular PBS/PLA foams for selective oil absorption

To address the challenges posed by spilled oil and oily wastewater, the development of clean oil-adsorption materials is crucial. However, traditional oil-adsorption materials suffer from the issue of secondary pollution. Herein, fully biodegradable nanofibrillated poly(butylene succinate)/poly(lactic acid) (PBS/PLA) foams with outstanding selective oil-adsorption performance were successfully fabricated via an eco-friendly supercritical CO2 foaming technology. The PBS/PLA composites, featuring nanofibrils with a diameter of approximately 100 nm, were prepared through a hot-stretching method subsequent to extrusion. Substantial improvements were observed in the crystallization rate and rheological properties of the fibrillated PBS/PLA composites. Furthermore, PLA nanofibrils enhanced foamability of the composite, achieving an impressive expansion ratio of up to 38.0, resulting in an outstanding oil-absorption performance (19.2-50.4 g/g) of the F-1 %-95 foam. Additionally, 20 adsorption-desorption cycles illustrated the prepared F-1 %-95 foam displayed recyclable oil-absorption characteristics. This work provides an eco-friendly strategy for preparing fully biodegradable foams intended for application as oil-adsorption materials.

Activities of cellulose acetate and microcrystalline cellulose on the thermal and morphomechanical performances of a biobased hybrid composite made polybutylene succinate

Microcrystalline cellulose (MCC-30 wt%) was extruded with a blend of polybutylene succinate (PBS) and cellulose acetate (CADS=2.5-20 wt%) to produce two grades of binary (PBS/CA, PBS/MCC) and ternary (PBS/CA/MCC) specimens by injection into a mold previously thermostated at 22 °C and 78 °C. The structure-property relationships of neat PBS (n-PBS) and PBS-based blends were investigated by Fourier transform infrared (FTIR) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, scanning electron microscopy (SEM), rheology, differential scanning calorimetry (DSC), thermogravimetry, and mechanical (tensile, bending) tests. FTIR/DRIFT outcomes revealed physical interactions between the ingredients through hydrogen bonds. Rheology and SEM evidenced the presence of entanglements and micro-voids absent in n-PBS. Non-isothermal DSC showed that 22 °C-molded formulations displayed crystalline degrees higher than 78 °C-specimens, except for PBS/MCC. DSC-isothermal analysis showed a hindrance effect of CA on PBS/CA crystallinity and a nucleating impact of MCC on PBS/MCC. Tensile and bending moduli increased for both material grades while the elongation at break decreased. Entanglements and micro-voids had detrimental effects on stress levels because the maximum tensile strength decreased when each or both biofillers were added to PBS. These structural configurations were beneficial for bending strengths since all blends' stiffness relatively increased regardless of material grade.

Green Solvent-Based Antifouling Polymer Brushes Demonstrate Excellent Hemocompatibility

Medical devices are crucial for patient care, yet even the best biomaterials lead to infections and unwanted activation of blood coagulation, potentially being life-threatening. While hydrophilic polymer brushes are the best coatings to mitigate these issues, their reliance on fossil raw materials underscores the urgency of bio-based alternatives. In this work, we introduce polymer brushes of a green solvent-based monomer, prohibiting protein adsorption, bacterial colonization, and blood clot formation at the same level as fossil-based polymer brushes. The polymer brushes are composed of N,N-dimethyl lactamide acrylate (DMLA), can be polymerized in a controlled manner, and show strong hydrophilicity as determined by thermodynamic analysis of the surface tension components. The contact of various challenging protein solutions results in repellency on the poly(DMLA) brushes. Furthermore, the poly(DMLA) brushes completely prevent the adhesion and colonization of Escherichia coli. Remarkably, upon blood contact, the poly(DMLA) brushes successfully prevent the formation of a fibrin network and leukocyte adhesion on the surface. While showcasing excellent antifouling properties similar to those of N-hydroxypropyl methacrylamide (HPMA) polymer brushes as one of the best antifouling coatings, the absence of hydroxyl groups prevents activation of the complement system in blood. We envision the polymer brushes to contribute to the future of hemocompatible coatings.

Synthesis and Properties of Polybutylene (Succinate)-b-poly(dimethylsiloxane) with Unprecedented Combined Performance and Functions

The excellent combined properties of poly(butylene succinate) (PBS) make it a promising biodegradable plastic. However, the lack of functionality and low impact strength limit its application. Poly(dimethylsiloxane) (PDMS) was introduced to prepare new high-performance and functional poly(butylene succinate)-b-poly(dimethylsiloxane) (PBS-b-PDMS) in this work. The resulting PBS-b-PDMS was found to possess high molecular weight, narrow molecular weight distribution, and excellent combined performance. PBS-b-PDMS had good thermal properties. The decomposition temperature of 5% weight loss (T5%) increased from 324 to 344 °C, and the temperatures at the maximum weight loss rate (Tmax) values increased from 385.1 to 396.7 °C. The impact strength increased significantly from 7.8 kJ/m2 of PBS to 53.9 kJ/m2 of PBS-b-PDMS. As the PDMS block endows copolymers with low surface energy and good liquid resistance, PBS-b-PDMS has excellent antismudge, self-cleaning, and solvent resistance. Finally, to minimize the surface energy, PDMS blocks preferentially enrich the surface, which imparts the polymers with self-cleaning properties.

Biodegradable Poly(butylene succinate) Laminate with Nanocellulose Interphase Layer for High-Barrier Packaging Film Application

In response to rising concerns over the environmental and human health ramifications of polymers derived from petroleum, particularly in the food packaging industry, research has pivoted towards more sustainable materials. Poly(butylene succinate) (PBS), selected as the polymer matrix, stands out as one of the most promising bio-based and biodegradable polymers suitable for film blowing and lamination. A layered spray-coating technique was employed to apply 1, 5, 10, and 20 layers of nanofibrillated cellulose (NFC) between blown PBS films, creating a three-layer laminate structure. NFC sourced from minimally processed hemp stalk waste highlights the potential for minimizing environmental impact. The water vapor transmission rate (WVTR) of these films, a critical parameter for food packaging, was assessed in a controlled environment at 38 °C and 90% relative humidity over a period of two months. The integration of a single NFC layer, constituting 0.35% of the composite's weight, was observed to significantly reduce the WVTR by up to 5.5-fold. It was noted that higher NFC layer counts above 10 reduced the adhesion within the laminate layers. Morphological assessments showed that the number of structural defects increased with a higher count of NFC layers. As the count of NFC layers increased, the optical transparency of the laminates dropped from approximately 65% to 25% in the visible light spectrum. Notably, by weight percent, NFC proved to be an effective barrier even without chemical modification. The developed laminates stand out as a viable, green option for food packaging, offering a sustainable and renewable solution.

Butyl succinate-mediated control of Bacillus velezensis ce 100 for apple anthracnose caused by Colletotrichum gloeosporioides

AIMS

Microbial biocontrol agents have become an effective option to mitigate the harmfulness of chemical pesticides in recent years. This study demonstrates the control efficacy of Bacillus velezensis CE 100 on the anthracnose causal agent, Colletotrichum gloeosporioides.

METHODS AND RESULTS

In vitro antifungal assays revealed that the culture filtrate and volatile organic compounds of B. velezensis CE 100 strongly restricted the mycelial development of C. gloeosporioides. Moreover, a bioactive compound, butyl succinate, was isolated from the n-butanol crude extract of B. velezensis CE 100 (bce), and identified by liquid chromatography-electrospray ionization hybrid ion-trap and time-of-flight mass spectrometry (LC-ESI-QTOF-MS) and one-dimensional (1D) and two-dimensional (2D) nuclear magnetic resonance (NMR). Treatment with purified butyl succinate at a concentration of 300 μg mL-1 strongly controlled conidial germination of C. gloeosporioides with an inhibition rate of 98.66%, whereas butyl succinate at a concentration of 400 μg mL-1 showed weak antifungal action on the mycelial growth of C. gloeosporioides with an inhibition rate of 31.25%. Scanning electron microscopy revealed that the morphologies of butyl succinate-treated hyphae and conidia of C. gloeosporioides were severely deformed with shriveled and wrinkled surfaces. Furthermore, butyl succinate was able to control carbendazim-resistant C. gloeosporioides, demonstrating that it could be a promising agent for the suppression of other carbendazim-resistant fungal pathogens. An in vivo biocontrol assay demonstrated that the strain ce 100 broth culture and butyl succinate showed higher control efficacy on apple anthracnose than bce.

CONCLUSIONS

Our findings provide insight into the antifungal potential of B. velezensis  ce 100 and its butyl succinate for efficient control of phytopathogenic fungi, such as C. gloeosporiodes, in plant disease protection. This is the first study to demonstrate the antifungal potential of bacteria-derived butyl succinate for control of C. gloeosporioides.

Achieving High-Performance Green Composites from Pineapple Leaf Fiber-Poly(butylene succinate) through Both Fiber Alignment and Matrix Orientation across the Thickness

This research aims to develop high-performance and low-carbon composites using biobased poly(butylene succinate) (PBS) reinforced with well-aligned pineapple leaf fibers (PALF). PBS/PALF composites containing 10 and 20% PALF by weight (wt %) were prepared using a two-roll mill. During the mixing process, the molten material was slightly stretched to align the fibers in the machine direction, forming a uniaxial prepreg. The prepreg was subsequently stacked and compressed into composite sheets at compression temperatures of 120 and 140 °C. Differential scanning calorimetry, X-ray diffraction, and crystalline morphology analysis revealed the presence of matrix orientation in the prepreg, which was preserved in sheets compressed at 120 °C but not at 140 °C. The composites prepared at 120 °C exhibited significantly higher flexural strength and modulus compared to those prepared at 140 °C, attributed to the combined effect of matrix and PALF orientation. Additionally, the composites displayed an increase in heat distortion temperature, with a maximum of 10 °C higher than the matrix melting temperature (∼113 °C) for the composite with 20 wt % PALF. These findings indicate the potential for increased utilization of this low-carbon green composite.

Plastics today: Key challenges and EU strategies towards carbon neutrality: A review

Never as today the need for collaborative interactions between industry, the scientific community, NGOs, policy makers and citizens has become crucial for the development of shared political choices and protection of the environment, for the safeguard of future generations. The complex socio-economic and environmental interconnections that underlie the EU strategy of the last years, within the framework of the Agenda 2030 and the green deal, often create perplexity and confusion that make difficult to outline the definition of a common path to achieve carbon neutrality and "net zero emissions" by 2050. Scope of this work is to give a general overview of EU policies, directives, regulations, and laws concerning polymers and plastic manufacturing, aiming to reduce plastic pollution, allowing for a better understanding of the implications that environmental concern and protection may generate from a social-economical point of view.

Comparative Study of Flax and Pineapple Leaf Fiber Reinforced Poly(butylene succinate): Effect of Fiber Content on Mechanical Properties

In this study, we compare the reinforcing efficiency of pineapple leaf fiber (PALF) and cultivated flax fiber in unidirectional poly(butylene succinate) composites. Flax, known for robust mechanical properties, is contrasted with PALF, a less studied but potentially sustainable alternative. Short fibers (6 mm) were incorporated at 10 and 20% wt. levels. After two-roll mill mixing, uniaxially aligned prepreg sheets were compression molded into composites. At 10 wt.%, PALF and flax exhibited virtually the same stress-strain curve. Interestingly, PALF excelled at 20 wt.%, defying its inherently lower tensile properties compared to flax. PALF/PBS reached 70.7 MPa flexural strength, 2.0 GPa flexural modulus, and 107.3 °C heat distortion temperature. Comparable values for flax/PBS were 57.8 MPa, 1.7 GPa, and 103.7 °C. X-ray pole figures indicated similar matrix orientations in both composites. An analysis of extracted fibers revealed differences in breakage behavior. This study highlights the potential of PALF as a sustainable reinforcement option. Encouraging the use of PALF in high-performance bio-composites aligns with environmental goals.

Effect of Incorporation of Graphene Nanoplatelets on Physicochemical, Thermal, Rheological, and Mechanical Properties of Biobased and Biodegradable Blends

This work aimed to study the effect of the incorporation of graphene nanoplatelets (GRA 0.5% and 1% (w/w)) on the matrices of biobased polymers composed of starch-based materials (B20) and poly(butylene succinate) (PBS) using pine rosin (RES) as a compatibilizer. Three formulations were produced (B20/RES/PBS, B20/RES/PBS/GRA0.5%, and B20/RES/PBS/GRA1%), and their mechanical properties (tensile, flexural, hardness, and impact), rheological behavior, thermal properties (thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC)), chemical analysis (Fourier transform infrared-attenuated total reflectance (FTIR-ATR) spectroscopy), and contact angle were evaluated. Hardness (Shore D), tensile, and flexural moduli increased, whereas elongation at break and toughness decreased as GRA content increased. FTIR studies strongly supported the existence of interactions between polymeric matrices and the large surface area of GRA. The viscosity flow curves were well fitted to the Cross-Williams-Landel-Ferry (Cross-WLF) model, and the three formulations exhibited non-Newtonian (shear-thinning) behavior. The analysis of water contact angles indicated that the formulation surfaces have hydrophilic behavior. All the samples are thermally stable, and the results of this study can be used to optimize the application of biobased graphene-based composites for applications in injection molding industries.

A Review of Biodegradable Plastics: Chemistry, Applications, Properties, and Future Research Needs

Environmental concerns over waste plastics' effect on the environment are leading to the creation of biodegradable plastics. Biodegradable plastics may serve as a promising approach to manage the issue of environmental accumulation of plastic waste in the ocean and soil. Biodegradable plastics are the type of polymers that can be degraded by microorganisms into small molecules (e.g., H2O, CO2, and CH4). However, there are misconceptions surrounding biodegradable plastics. For example, the term "biodegradable" on product labeling can be misconstrued by the public to imply that the product will degrade under any environmental conditions. Such misleading information leads to consumer encouragement of excessive consumption of certain goods and increased littering of products labeled as "biodegradable". This review not only provides a comprehensive overview of the state-of-the-art biodegradable plastics but also clarifies the definitions and various terms associated with biodegradable plastics, including oxo-degradable plastics, enzyme-mediated plastics, and biodegradation agents. Analytical techniques and standard test methods to evaluate the biodegradability of polymeric materials in alignment with international standards are summarized. The review summarizes the properties and industrial applications of previously developed biodegradable plastics and then discusses how biomass-derived monomers can create new types of biodegradable polymers by utilizing their unique chemical properties from oxygen-containing functional groups. The terminology and methodologies covered in the paper provide a perspective on directions for the design of new biodegradable polymers that possess not only advanced performance for practical applications but also environmental benefits.

Recyclable and Degradable Ionic-Substituted Long-Chain Polyesters

Ionic groups can endow apolar polymers like polyethylene with desirable traits like adhesion with polar compounds. While ethylene copolymers provide a wide range of tunability via the carboxylate content and neutralization with different cations, they lack degradability or suitability for chemical recycling due to their all-carbon backbones. Here, we report ion-containing long-chain polyesters with low amounts of ionic groups (Mn = 50-60 kg/mol, <0.5 mol % of ionic monomers) which can be synthesized from plant oils and exhibit HDPE-like character in their structural and mechanical properties. In the sulfonic acid as well as neutralized sulfonate-containing polyesters, the nature of the cation counterions (Mg2+, Ca2+, and Zn2+) significantly impacts the mechanical properties and melt rheology. Acid-containing polyesters exhibit a relatively high capability to absorb water and are susceptible to abiotic degradation. Enhanced surface wettability is reflected by facilitation of printing on films of these polymers. Depolymerization by methanolysis to afford the neat long-chain monomers demonstrates the suitability for chemical recycling. The surface properties of the neutralized sulfonate-containing polyesters are enhanced, showing a higher adsorption capability. Our findings allow for tuning the properties of recyclable polyethylene-like polymers and widen the scope of these promising materials.

The Effect of Biochar Addition on Thermal Stability and Decomposition Mechanism of Poly(butylene succinate) Bionanocomposites

In the present study, poly(butylene succinate) (PBSu) and its bionanocomposites containing 1, 2.5, and 5 wt.% biochar (MSP700) were prepared via in situ melt polycondensation in order to investigate the thermal stability and decomposition mechanism of the materials. X-ray photoelectron spectroscopy (XPS) measurements were carried out to analyze the surface area of a biochar sample and PBSu/biochar nanocomposites. From XPS, it was found that only physical interactions were taking place between PBSu matrix and biochar nanoadditive. Thermal stability, decomposition kinetics, and the decomposition mechanism of the pristine PBSu and PBSu/biochar nanocomposites were thoroughly studied by thermogravimetric analysis (TGA) and pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS). TGA thermograms depicted that all materials had high thermal stability, since their decomposition started at around 300 °C. However, results indicated a slight reduction in the thermal stability of the PBSu biochar nanocomposites because of the potential catalytic impact of biochar. Py-GC/MS analysis was employed to examine, in more detail, the thermal degradation mechanism of PBSu nanocomposites filled with biochar. From the decomposition products identified by Py-GC/MS after pyrolysis at 450 °C, it was found that the decomposition pathway of the PBSu/biochar nanocomposites took place mainly via β-hydrogen bond scission, which is similar to that which took place for neat PBSu. However, at higher biochar content (5 wt.%), some localized differences in the intensity of the peaks of some specific thermal degradation products could be recognized, indicating that α-hydrogen bond scission was also taking place. A study of the thermal stability and decomposition pathway of PBSu/biochar bionanocomposites is crucial to examine if the new materials fulfill the requirements for further investigation for mulch films in agriculture or in electronics as possible applications.

Influence of Coffee Variety and Processing on the Properties of Parchments as Functional Bioadditives for Biobased Poly(butylene succinate) Composites

Fermented polymers like biobased poly(butylene succinate) (BioPBS) have become more relevant as technical substitutes for ductile petrochemical-based polymers but require biogenic functional additives to deaccelerate undesired thermo-oxidative degradation and keep a fully biobased character. In this paper, the influence of coffee parchment (PMT) from two different varieties and processings on the thermo-oxidative stabilization and mechanical properties of poly(butylene succinate) composites up to 20 wt.-% PMT were investigated. Micronized with a TurboRotor mill, both PMT powders differ in particle size and shape, moisture ab- and adsorption behavior and antioxidative properties. It could be shown that pulped-natural PMT consists partially of coffee cherry residues, which leads to a higher total polyphenol content and water activity. The homogeneous PMT from fully washed processing has a higher thermal degradation resistance but consists of fibers with larger diameters. Compounded with the BioPBS and subsequent injection molded, the fully washed PMT leads to higher stiffness and equal tensile strength but lower toughness compared to the pulped-natural PMT, especially at lower deformation speed. Surprisingly, the fully washed PMT showed a higher stability against thermo-oxidative decomposition despite the lower values in the total phenol content and antioxidative activity. The required antioxidative stabilizers might be extracted at higher temperatures from the PMT fibers, making it a suitable biogenic stabilizer for extrusion processes.

Pilot-Scale Melt Electrospinning of Polybutylene Succinate Fiber Mats for a Biobased and Biodegradable Face Mask

The COVID-19 pandemic led to a huge demand for disposable facemasks. Billions were manufactured from nonbiodegradable petroleum-derived polymers, and many were discarded in the environment where they contributed to plastic pollution. There is an urgent need for biobased and biodegradable facemasks to avoid environmental harm during future disease outbreaks. Melt electrospinning is a promising alternative technique for the manufacturing of filter layers using sub-microfibers prepared from biobased raw materials such as polybutylene succinate (PBS). However, it is not yet possible to produce sub-micrometer PBS fibers or uniform nonwoven-like samples at the pilot scale, which hinders their investigation as filter layers. Further optimization of pilot-scale PBS melt electrospinning is therefore required. Here, we tested the effect of different parameters such as electric field strength, nozzle-to-collector distance and throughput on the final fiber diameter and sample uniformity during PBS melt electrospinning on a pilot-scale device. We also studied the effect of a climate chamber and an additional infrared heater on the solidification of PBS fibers and their final diameter and uniformity. In addition, a post-processing step, including a hot air stream of 90 °C for 30 s has been studied and successfully lead to a nonwoven-like structure including filaments that weld together without changing their structure. The finest fibers (1.7 µm in diameter) were produced at an applied electric field strength of -40 kV, a nozzle-to-collector distance of 5.5 cm, and a spin pump speed of 2 rpm. Three uniform nonwoven-like samples were tested as filter layers in a medical face mask by measuring their ability to prevent the transfer of bacteria, but the pore size was too large for effective retention. Our results provide insight into the process parameters influencing the suitability of melt-electrospun nonwoven-like samples as biobased and biodegradable filter materials and offer guidance for further process optimization.

Development and Characterization of Thermoformed Bilayer Trays of Paper and Renewable Succinic Acid Derived Biopolyester Blends and Their Application to Preserve Fresh Pasta

The present study reports on the development by thermoforming of highly sustainable trays based on a bilayer structure composed of paper substrate and a film made of a blend of partially bio-based poly(butylene succinate) (PBS) and poly(butylene succinate-co-adipate) (PBSA). The incorporation of the renewable succinic acid derived biopolyester blend film slightly improved the thermal resistance and tensile strength of paper, whereas its flexural ductility and puncture resistance were notably enhanced. Furthermore, in terms of barrier properties, the incorporation of this biopolymer blend film reduced the water and aroma vapor permeances of paper by two orders of magnitude, while it endowed the paper structure with intermediate oxygen barrier properties. The resultant thermoformed bilayer trays were, thereafter, originally applied to preserve non-thermally treated Italian artisanal fresh pasta, "fusilli calabresi" type, which was stored under refrigeration conditions for 3 weeks. Shelf-life evaluation showed that the application of the PBS-PBSA film on the paper substrate delayed color changes and mold growth for 1 week, as well as reduced drying of fresh pasta, resulting in acceptable physicochemical quality parameters within 9 days of storage. Lastly, overall migration studies performed with two food simulants demonstrated that the newly developed paper/PBS-PBSA trays are safe since these successfully comply with current legislation on plastic materials and articles intended to come into contact with food.

Additive Manufacturing of Biodegradable Hemp-Reinforced Polybutylene Succinate (PBS) and Its Mechanical Characterization

The additive manufacturing of natural fibre-reinforced polymers is a pivotal method in developing sustainable engineering solutions. Using the fused filament fabrication method, the current study investigates the additive manufacturing of hemp-reinforced polybutylene succinate (PBS) alongside its mechanical characterization. Two types of hemp reinforcement are considered: short fibres (max. length smaller than 2 mm) and long fibres (max. length smaller than 10 mm), which are compared against non-reinforced (pure) PBS. A detailed analysis is performed regarding the determination of suitable 3D printing parameters (overlap, temperature, nozzle diameter). In a comprehensive experimental study, additionally to general analyses regarding the influence of hemp reinforcement on the mechanical behaviour, the effect of printing parameters is determined and discussed. Introducing an overlap in the additive manufacturing of the specimens results in improved mechanical performance. The study highlights that the Young's modulus of PBS can be improved by 63% by introducing hemp fibres in conjunction with overlap. In contrast, hemp fibre reinforcement reduces the tensile strength of PBS, while this effect is less pronounced considering overlap in the additive manufacturing process.

Coir fiber as thermal insulator and its performance as reinforcing material in biocomposite production

Coir is a lignocellulosic natural fiber derived from the coconut's husk, an abundantly found fruit or nut worldwide. This fiber has some unique characteristics, such as its resistance to seawater, microbial attack, high impact, etc. But its low thermal conductivity or high thermal insulating property makes it suitable for being used as insulators in civil engineering sites. On the other hand, the sustainability of a material depends heavily on its environmental impact of the material. For making sustainable materials like biocomposite, there are no options other than using polymers derived from natural renewable sources. Polylactic acid(PLA) is an example of those types of material. And these materials are often being reinforced by fibers like coir for various reasons including improving mechanical properties, reducing the cost of the material, and improving the material's sustainability. Many coir-reinforced sustainable biopolymer composites have already been produced in many pieces of research, which will be discussed in this paper, along with the chemical and physical structure of coir fiber. In addition, this paper will try to focus on the insulating properties of coir and coir-reinforced composites while will also compare some properties of the composites with some commonly used materials based on different parameters to show the suitability of using the coir fiber in heat-insulating applications and to produce sustainable biocomposite materials.

Mechanical, chemical, and bio-recycling of biodegradable plastics: A review

The extensive use of petroleum-based non-biodegradable plastics for various applications has led to global concerns regarding the severe environmental issues associated with them. However, biodegradable plastics are emerging as green alternatives to petroleum-based non-biodegradable plastics. Biodegradable plastics, which include bio-based and petroleum-based biodegradable polymers, exhibit advantageous properties such as renewability, biocompatibility, and non-toxicity. Furthermore, certain biodegradable plastics are compatible with existing recycling streams intended for conventional plastics and are biodegradable in controlled and/or predicted environments. Recycling biodegradable plastics before their end-of-life (EOL) degradation further enhances their sustainability and reduces their carbon footprint. Since the production of biodegradable plastic is increasing and these materials will coexist with conventional plastics for many years to come, it is essential to identify the optimal recycling options for each of the most prevalent biodegradable plastics. The substitution of virgin biodegradable plastics by their recyclates leads to higher savings in the primary energy demand and reduces global warming impact. This review covers the current state of the mechanical, chemical, and bio-recycling of post-industrial and post-consumer waste of biodegradable plastics and their related composites. The effects of recycling on the chemical structure and thermomechanical properties of biodegradable plastics are also reported. Additionally, the improvement of biodegradable plastics by blending them with other polymers and nanoparticles is comprehensively discussed. Finally, the status of bioplastic usage, life cycle assessment, EOL management, bioplastic market, and the challenges associated with the recyclability of biodegradable plastics are addressed. This review gives comprehensive insights into the recycling processes that may be employed for the recycling of biodegradable plastics.

Seawater Biodegradable Poly(butylene succinate-co-adipate)-Wheat Bran Biocomposites

The present work focused on the development and characterization of biocomposites based on a fully bio-based polyester, poly(butylene succinate-co-butylene adipate) (PBSA), and wheat bran derived by flour milling. PBSA-bran composites containing 5, 10, 15, and 20 wt.% of wheat bran were produced via melt extrusion and processed by injection molding. Their thermal, rheological, morphological, and tensile properties were investigated. In addition, a biodegradation test in a natural marine environment was conducted on composite dog-bones to assess the capacity of the used filler to increase the PBSA biodegradation rate. The composites maintained similar melt processability and mechanical properties to virgin PBSA with up to 15 wt.% bran content. This result was also supported by morphological investigation, which showed good filler dispersion within the polymer matrix at low-mid bran content, whereas poor polymer-filler dispersion occurred at higher concentrations. Furthermore, the biodegradation tests showed bran's capacity to improve the PBSA biodegradation rate, probably due to the hygroscopic bran swelling, which induced the fragmentation of the dog-bone with a consequent increase in the polymeric matrix-seawater interfacial area, accelerating the degradation mechanisms. These results encourage the use of wheat bran, an abundant and low-cost agri-food by-product, as a filler in PBSA-based composites to develop products with good processability, mechanical properties, and controlled biodegradability in marine environments.

Anaerobic Biodegradability of Commercial Bioplastic Products: Systematic Bibliographic Analysis and Critical Assessment of the Latest Advances

Bioplastics have entered everyday life as a potential sustainable substitute for commodity plastics. However, still further progress should be made to clarify their degradation behavior under controlled and uncontrolled conditions. The wide array of biopolymers and commercial blends available make predicting the biodegradation degree and kinetics quite a complex issue that requires specific knowledge of the multiple factors affecting the degradation process. This paper summarizes the main scientific literature on anaerobic digestion of biodegradable plastics through a general bibliographic analysis and a more detailed discussion of specific results from relevant experimental studies. The critical analysis of literature data initially included 275 scientific references, which were then screened for duplication/pertinence/relevance. The screened references were analyzed to derive some general features of the research profile, trends, and evolution in the field of anaerobic biodegradation of bioplastics. The second stage of the analysis involved extracting detailed results about bioplastic degradability under anaerobic conditions by screening analytical and performance data on biodegradation performance for different types of bioplastic products and different anaerobic biodegradation conditions, with a particular emphasis on the most recent data. A critical overview of existing biopolymers is presented, along with their properties and degradation mechanisms and the operating parameters influencing/enhancing the degradation process under anaerobic conditions.

Polymers without Petrochemicals: Sustainable Routes to Conventional Monomers

Access to a wide range of plastic materials has been rationalized by the increased demand from growing populations and the development of high-throughput production systems. Plastic materials at low costs with reliable properties have been utilized in many everyday products. Multibillion-dollar companies are established around these plastic materials, and each polymer takes years to optimize, secure intellectual property, comply with the regulatory bodies such as the Registration, Evaluation, Authorisation and Restriction of Chemicals and the Environmental Protection Agency and develop consumer confidence. Therefore, developing a fully sustainable new plastic material with even a slightly different chemical structure is a costly and long process. Hence, the production of the common plastic materials with exactly the same chemical structures that does not require any new registration processes better reflects the reality of how to address the critical future of sustainable plastics. In this review, we have highlighted the very recent examples on the synthesis of common monomers using chemicals from sustainable feedstocks that can be used as a like-for-like substitute to prepare conventional petrochemical-free thermoplastics.

Investigation on the Photodegradation Stability of Acrylic Acid-Grafted Poly(butylene carbonate-co-terephthalate)/Organically Modified Layered Zinc Phenylphosphonate Composites

The application efficiency of biodegradable polymers used in a natural environment requires improved resistance to ultraviolet (UV) photodegradation. In this report, 1,6-hexanediamine modified layered zinc phenylphosphonate (m-PPZn), utilized as a UV protection additive for acrylic acid-grafted poly(butylene carbonate-co-terephthalate) (g-PBCT), was successfully fabricated and compared to the solution mixing process. Experimental data of both wide-angle X-ray diffraction and transmission electron microscopy reveal that the g-PBCT polymer matrix was intercalated into the interlayer spacing of m-PPZn, which was approximately delaminated in the composite materials. The evolution of photodegradation behavior for g-PBCT/m-PPZn composites was identified using Fourier transform infrared spectroscopy and gel permeation chromatography after being artificially irradiated by a light source. The change of carboxyl group produced via photodegradation was used to show the enhanced UV protection ability of m-PPZn in the composite materials. All results indicate that the carbonyl index of the g-PBCT/m-PPZn composite materials after photodegradation for 4 weeks was extensively lower than that of the pure g-PBCT polymer matrix. These findings were also supported by the decrease in the molecular weight of g-PBCT after photodegradation for 4 weeks, from 20.76% to 8.21%, with the loading of 5 wt% m-PPZn content. Both observations were probably owing to the better UV reflection ability of m-PPZn. This investigation shows, through typical methodology, a significant advantage of fabricating the photodegradation stabilizer to enhance the UV photodegradation behavior of the biodegradable polymer using an m-PPZn compared to other UV stabilizer particles or additives.

Preparation and Characterization of New Bioplastics Based on Polybutylene Succinate (PBS)

Sea and environmental pollution due to microplastics are global problems that in recent years have attracted particular interest in the scientific community. The increase in the world population and the consequent consumerism of non-reusable materials are amplifying these problems. In this manuscript, we present novel bioplastics, which are completely biodegradable, for their potential use in food packaging, to replace fossil-fuel-derived plastic films and slow food degradation due to oxidative processes or microbial contamination. In this study, thin films based on polybutylene succinate (PBS) were prepared to reduce pollution, and different percentages by weight (1, 2 and 3 wt%) of extra virgin olive oil (EVO) and coconut oil (CO) were included to improve the chemico-physical properties of the polymer and possibly improve the functionality of the films in terms of prolonged food preservation. Attenuated total reflectance Fourier transform infrared (ATR/FTIR) spectroscopy was used to evaluate the interactions between the polymer and the oil. Furthermore, the mechanical properties and thermal behavior of the films were evaluated as a function of the oil content. A scanning electron microscopy (SEM) micrograph showed the surface morphology and the thickness of the materials. Finally, apple and kiwi were selected for a food-contact test, and the wrapped sliced fruit was monitored and evaluated for 12 days to macroscopically evaluate the oxidative process and/or eventually occurring contamination. The films were shown to reduce the browning of sliced fruit due to oxidation, and no molds were evidenced up to 10/12 days of observation with the addition of PBS, with 3 wt% of EVO achieving the best outcomes.

Synthesis and Study of Fully Biodegradable Composites Based on Poly(butylene succinate) and Biochar

Biodegradable polymers offer a promising alternative to the global plastic problems and especially in the last decade, to the microplastics problems. For the first time, samples of poly(butylene succinate) (PBSu) biocomposites containing 1, 2.5, and 5 wt% biochar (BC) were prepared by in situ polymerization via the two-stage melt polycondensation procedure. BC was used as a filler for the PBSu to improve its mechanical properties, thermal transitions, and biodegradability. The structure of the synthesized polymers was examined by ¹H and ¹³C nuclear magnetic resonance (NMR) and X-Ray diffraction (XRD) along with an estimation of the molecular weights, while differential scanning calorimetry (DSC) and light flash analysis (LFA) were also employed to record the thermal transitions and evaluate the thermal conductivity, respectively. It was found that the amount of BC does not affect the molecular weight of PBSu biocomposites. The fine dispersion of BC, as well as the increase in BC content in the polymeric matrix, significantly improves the tensile and impact strengths. The DSC analysis results showed that BC facilitates the crystallization of PBSu biocomposites. Due to the latter, a mild and systematic increase in thermal diffusivity and conductivity was recorded indicating that BC is a conductive material. The molecular mobility of PBSu, local and segmental, does not change significantly in the biocomposites, whereas the BC seems to cause an increase in the overall dielectric permittivity. Finally, it was found that the enzymatic hydrolysis degradation rate of biocomposites increased with the increasing BC content.

Wool Keratin Nanofibers for Bioinspired and Sustainable Use in Biomedical Field

Keratin is a biocompatible and biodegradable protein as the main component of wool and animal hair fibers. Keratin-based materials support fibroblasts and osteoblasts growth. Keratin has been extracted by sulphitolysis, a green method (no harmful chemicals) with a yield of 38-45%. Keratin has been processed into nanofibers from its solutions by electrospinning. Electrospinning is a versatile and easy-to-use technique to generate nanofibers. It is an eco-friendly and economical method for the production of randomly and uniaxially oriented polymeric nanofibers. Thanks to their high specific surface area, nanofibers have great potential in the biomedical field. Keratin nanofibers have received significant attention in biomedical applications, such as tissue engineering and cell growth scaffolds, for their biocompatibility and bio-functionality. Accordingly, we propose an extensive overview of recent studies focused on the optimization of keratinbased nanofibers, emphasizing their peculiar functions for cell interactions and the role of additive phases in blends or composite systems to particularize them as a function of specific applications (i.e., antibacterial).

Polyesters Incorporating Gallic Acid as Oxygen Scavenger in Biodegradable Packaging

Biodegradable polyesters polybutylene succinate (PBS) and polybutylene adipate-co-terephthalate (PBAT) were blended with gallic acid (GA) via cast extrusion to produce oxygen scavenging polymers. The effects of polyesters and GA contents (5 to 15%) on polymer/package properties were investigated. Increasing GA formed non-homogeneous microstructures and surface roughness due to immiscibility. GA had favorable interaction with PBAT than PBS, giving more homogeneous microstructures, reduced mechanical relaxation temperature, and modified X-ray diffraction and crystalline morphology of PBAT polymers. Non-homogenous dispersion of GA reduced mechanical properties and increased water vapor and oxygen permeability by two and seven folds, respectively. Increasing amounts of GA and higher humidity enhanced oxygen absorption capacity, which also depended on the dispersion characteristics of GA in the matrices. PBAT gave higher oxygen absorption than PBS due to better dispersion and higher reactive surface area. GA blended with PBAT and PBS increased oxygen scavenging activity as sustainable active food packaging using functional biodegradable polymers.

Development of Blends to Improve Flexibility of Biodegradable Polymers

In this study, binary blends of biodegradable polymers were prepared to improve the ductile properties of those that have a more rigid and/or brittle behaviour. Specifically, PLA, PHA and TPS were blended with different amounts of PBS with the objective of reducing the stiffness and brittleness of the three polymers. The compatibility of the blends and their resulting mechanical properties were studied. The flexibility of the blends increased with the addition of PBS; however, a limited compatibility was achieved, leading to a low impact resistance improvement. For this reason, other blend options with an EVA-based material were studied, increasing the impact resistance and flexibility of the PLA material in this case.

Polymers Use as Mulch Films in Agriculture-A Review of History, Problems and Current Trends

The application of mulch films for preserving soil moisture and preventing weed growth has been a part of agricultural practice for decades. Different materials have been used as mulch films, but polyethylene plastic has been considered most effective due to its excellent mechanical strength, low cost and ability to act as a barrier for sunlight and water. However, its use carries a risk of plastic pollution and health hazards, hence new laws have been passed to replace it completely with other materials over the next few years. Research to find out about new biodegradable polymers for this purpose has gained impetus in the past few years, driven by regulations and the United Nations Organization's Sustainable Development Goals. The primary requisite for these polymers is biodegradability under natural climatic conditions without the production of any toxic residual compounds. Therefore, biodegradable polymers developed from fossil fuels, microorganisms, animals and plants are viable options for using as mulching material. However, the solution is not as simple since each polymer has different mechanical properties and a compromise has to be made in terms of strength, cost and biodegradability of the polymer for its use as mulch film. This review discusses the history of mulching materials, the gradual evolution in the choice of materials, the process of biodegradation of mulch films, the regulations passed regarding material to be used, types of polymers that can be explored as potential mulch films and the future prospects in the area.

Synthesis of Biodegradable Polyester-Polyether with Enhanced Hydrophilicity, Thermal Stability, Toughness, and Degradation Rate

Novel poly(butylene succinate-butylene furandicarboxylate/polyethylene glycol succinate) (PBSF-PEG) was synthesized using two-step transesterification and polycondensation in the melt. There are characterized by intrinsic viscosity, GPC, ¹H NMR, DSC, TGA, tensile, water absorption tests, and water degradation at different pH. GPC analysis showed that PBSF-PEG had high molecular weight with average molecular weight (M_w) up to 13.68 × 10⁴ g/mol. Tensile tests showed that these polymers possessed good mechanical properties with a tensile strength as high as 30 MPa and elongation at break reaching 1500%. It should be noted that the increase of PEG units improved the toughness of the polyester material. In addition, the introduction of PEG promoted the water degradation properties of PBSF, and the copolymer showed a significantly faster water degradation rate when the PEG unit content was 20%. This suggests that the amount of PEG introduced could be applied to regulate the water degradation rate of the copolymers. Hence, these new polymers have great potential for application as environmentally friendly and sustainable plastic packaging materials.

Polybutylene Succinate Processing and Evaluation as a Micro Fibrous Graft for Tissue Engineering Applications

A microfibrous tubular scaffold has been designed and fabricated by electrospinning using poly (1,4-butylene succinate) as biocompatible and biodegradable material. The scaffold morphology was optimized as a small diameter and micro-porous conduit, able to foster cell integration, adhesion, and growth while avoiding cell infiltration through the graft's wall. Scaffold morphology and mechanical properties were explored and compared to those of native conduits. Scaffolds were then seeded with adult normal human dermal fibroblasts to evaluate cytocompatibility in vitro. Haemolytic effect was evaluated upon incubation with diluted whole blood. The scaffold showed no delamination, and mechanical properties were in the physiological range for tubular conduits: elastic modulus (17.5 ± 1.6 MPa), ultimate tensile stress (3.95 ± 0.17 MPa), strain to failure (57 ± 4.5%) and suture retention force (2.65 ± 0.32 N). The shown degradation profile allows the graft to provide initial mechanical support and functionality while being colonized and then replaced by the host cells. This combination of features might represent a step toward future research on PBS as a biomaterial to produce scaffolds that provide structure and function over time and support host cell remodelling.

Acceleration of Polybutylene Succinate Biodegradation by Terribacillus sp. JY49 Isolated from a Marine Environment

Polybutylene succinate (PBS) is a bioplastic substitute for synthetic plastics that are made from petroleum-based products such as polyethylene and polypropylene. However, the biodegradation rate of PBS is still low and similar to that of polylactic acid (PLA). Moreover, our knowledge about degrader species is limited to a few fungi and mixed consortia. Here, to identify a bacterial degrader to accelerate PBS degradation, we screened and isolated Terribacillus sp. JY49, which showed significant degradability. In order to optimize solid and liquid culture conditions, the effect of factors such as temperature, additional carbon sources, and salt concentrations on degradation was confirmed. We observed a degradation yield of 22.3% after 7 days when adding 1% of glucose. Additionally, NaCl was added to liquid media, and degradation yield was decreased but PBS films were broken into pieces. Comparing the degree of PBS degradation during 10 days, the degradation yield was 31.4% after 10 days at 30 °C. Alteration of physical properties of films was analyzed by using scanning electron microscopy (SEM), gel permeation chromatography (GPC), and Fourier transform infrared (FT-IR). In addition, Terribacillus sp. JY49 showed clear zones on poly(butylene adipate-co-terephthalate) (PBAT), polycaprolactone (PCL), and copolymers such as P(3HB-co-3HV) and P(3HV-co-4HB), exhibiting a broad spectrum of degradation activities on bioplastics. However, there was no significant difference in absorbance when esterase activity was examined for different types of bioplastics. Overall, Terribacillus sp. JY49 is a potential bacterial strain that can degrade PBS and other bioplastics, and this is the first report of Terribacillus sp. as a bioplastic degrader.