Insights in the Application of Stoichiometric and Non-Stoichiometric Titanium Oxides for the Design of Sensors for the Determination of Gases and VOCs (TiO2-x and TinO2n-1 vs. TiO2)

The O-Defective g-ZnO Sensor for VOC Gases: The Adsorption-Desorption, Electronic, and Sensitivity Properties

Adsorption-desorption performance, electronic properties, and sensitivity of O-defective g-ZnO (ODZO) gas sensors for volatile organic compounds (VOCs) are calculated using density functional theory and nonequilibrium Green's formalism. The VOCs are CH2O, CH4, C2H4O, CH4O, and C2H6. The intrinsic g-ZnO (IZO) and ODZO exhibit strong adsorption capabilities for C2H4O and CH4O. The IZO (0.118 e) and ODZO (0.059 e), which act as electron donors, exhibit the highest charge transfer to CH2O, indicating a strong interaction. The VOCs adsorption on the IZO and ODZO systems maintain nonmagnetic semiconductor characteristics. Additionally, the introduction of an O-defect causes the adsorption energy and charge transfer amount of ODZO to show an overall decrease, indicating better desorption ability. Notably, the sensitivity results show that the ODZO gas sensors exhibit high sensitivity to CH2O (39.3%), C2H4O (29.0%), and CH4O (19.6%) at a voltage of 2.6 V, consistent with the adsorption-desorption performance and electronic properties.

A double defects-dominated flexible TiO2 matrix for in-situ SERS sensing of antibiotic residues in aquatic ecosystem (fish & fishpond water) and their on-site degradation in flowing water

High-performance flexible semiconductor material can be used as an excellent multifunctional matrix for in-situ ultrasensitive surface-enhanced Raman scattering (SERS) detection and synchronous photocatalytic degradation of antibiotic residues in aquatic ecosystem. Here, a calcium-doped TiO2 flexible matrix with double defects (surface oxygen vacancy defect and Ti3+ energy level defect) was developed by its "in-situ one-step" hydrothermal synthesis on cotton fabric for the above purposes. Due to the joint contribution of double defects, a multi-channel charge transfer mode and a high-efficiency carrier separation are achieved, which endows flexible cotton fabric/Ca-doped TiO2 (Cot/Ca-TiO2) substrate with the greatly boosted SERS effect for in-situ detection of antibiotic residues on fish body surface and in fishpond water by a simple wiping or dipping sampling method, even for simultaneous identification of multi-component residues. The detection limits of three antibiotic residues (enrofloxacin, ciprofloxacin and enoxacin) are as low as 10-9 M, which are far lower than the EU standard. More meaningfully, the flexible Cot/Ca-TiO2 can be used as a multifunctional filter-membrane type photocatalyst for efficient on-site degradation of antibiotic residues in flowing fishpond water by a multi-grade photocatalysis means. Moreover, the flexible matrix exhibits good recyclability in both actual detection and photocatalysis.

Flexible Antibacterial Respiratory Monitoring Sensor Based on Controllable Au-Modified Surface of Highly {001} Preferred Anatase Titanium Dioxide Thin Film

Respiratory signals are critical clinical diagnostic criteria for respiratory diseases and health conditions, and respiratory sensors play a crucial role in achieving the desired respiratory monitoring effect. High sensitivity to a single factor can improve the reliability of respiratory monitoring, and maintaining the hygiene of the sensors is also important for daily health monitoring. Herein, we propose a flexible Au-modified anatase titanium dioxide resistive respiratory sensor, which can be mechanically compliantly attached to curved surfaces for respiratory monitoring in different modalities (i.e., respiratory intensity, frequency, and rate). The uniform and preferentially oriented anatase titanium dioxide films gained by the polymer-assisted deposition technique can be fabricated on flexible substrates through a liquid-assisted transferring process. The Au modification can enhance surface plasmon resonance to facilitate the photocatalytic activity of titanium dioxide, and the optimized distribution of Au on the surface of titanium dioxide film made the sensor have an excellent antibacterial effect. The uniquely designed encapsulation can effectively control the contact between the surface of titanium dioxide films and electrodes, allowing the flexible sensor to exhibit fast response time (0.71 s) and recovery time (1.06 s) to respiratory as well as insensitivity or low sensitivity to other factors (i.e., gas composition, humidity, temperature, stress, and strain). This work provided an effective strategy for flexible wearable respiratory sensors and has great potential in daily respiratory monitoring for health management and pandemic control.

MXene-Based Chemo-Sensors and Other Sensing Devices

MXenes have received worldwide attention across various scientific and technological fields since the first report of the synthesis of Ti3C2 nanostructures in 2011. The unique characteristics of MXenes, such as superior mechanical strength and flexibility, liquid-phase processability, tunable surface functionality, high electrical conductivity, and the ability to customize their properties, have led to the widespread development and exploration of their applications in energy storage, electronics, biomedicine, catalysis, and environmental technologies. The significant growth in publications related to MXenes over the past decade highlights the extensive research interest in this material. One area that has a great potential for improvement through the integration of MXenes is sensor design. Strain sensors, temperature sensors, pressure sensors, biosensors (both optical and electrochemical), gas sensors, and environmental pollution sensors targeted at volatile organic compounds (VOCs) could all gain numerous improvements from the inclusion of MXenes. This report delves into the current research landscape, exploring the advancements in MXene-based chemo-sensor technologies and examining potential future applications across diverse sensor types.

Fabrication and characterization of electrically conducting electrochemically synthesized polypyrrole-based enzymatic biofuel cell anode with biocompatible redox mediator vitamin K3

Enzymatic biofuel cells (EBFCs) hold tremendous potential to power biomedical devices, biosensors, and bioelectronics. Unlike conventional toxic batteries, these electrochemical devices are biocompatible, harnessing energy from physiological fluids and producing usable electrical energy. But the commercialization of EBFCs is limited by the low operational stability, limited power output and poor electron transport efficiency of the enzymatic electrodes. In this study, a novel bioanode exhibiting a high electron transfer ability and long-term stability was fabricated. For the preparation of the anode, surfactant-assisted polypyrrole (PPy) was electrochemically co-deposited on a platinum wire with the simultaneous entrapment of vitamin K3 (VK3) and GOx (glucose oxidase) in the PPy matrix. Herein, conducting PPy acts as an electron transfer enhancer and provides appropriate electrical communication between the active site of the enzyme glucose oxidase (GOx) and the electrode surface. Biocompatible redox mediator vitamin K3 was employed as an electron transfer mediator to shuttle electrons between the oxidized fuel glucose and surface of the electrode in the electrochemical cell. The electrical conductivity of PPy was measured using the four-probe technique of conductivity measurement of semiconductors. The morphological characterization of as-synthesized anode (PPy/CTAB/VK3/GOx) was performed by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical characterization was studied by cyclic voltammetry (CV), linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS) techniques. It was observed that the room-temperature conductivity of PPy lies in the semiconducting range and it also shows good stability on exposure to laboratory air, making it a promising material to provide electrical contact. The study developed a bioanode producing a modest current density of 6.35 mA cm-2 in 20 mM glucose solution. The stability, current output and ease of manufacturing process of the electrode make it particularly suitable for employment in biofuel cell applications.

Nanostructure-Based Solution Sensor Fabricated with p-CuOx/n-TiO2 Nanojunctions To Identify Species and Concentrations of Alcohol Molecules

Chemiresistive sensors fabricated based on metal-oxide-semiconductors, the most widely used high-sensitivity sensor materials, are required for detecting target solutions and gases and identifying them with a high degree of accuracy. In this study, we used p-n nanojunctions and nanowire shapes for identifying alcohol solutions. The solution sensors fabricated based on CuOx nanowires with p-CuOx/n-TiO2 nanojunctions detected ethanol, ethylene glycol, and diethylene glycol solutions via DC voltage and electrochemical impedance measurements. The p-n nanojunctions affected the sensors' sensitivity in the diethylene glycol solution, and the nanowire surface areas affected the relaxation time in ethanol and ethylene glycol solutions. To identify alcohol solutions, principal component analysis was performed based on the relationship between the sensor information, such as the presence of p-n nanojunctions and nanowire surface areas, and the sensing performance. This analysis identified alcohol molecular species and predicted alcohol-solution concentrations in the 0.1-20 vol % range with a high degree of accuracy. The concept of using sensors with different surface conditions with respect to p-n nanojunctions and nanowire surface areas offers designs for metal-oxide-semiconductor sensors to identify various molecules in solution.

A Review: Synthesis and Applications of Titanium Sub-Oxides

Magnéli phase titanium oxides, also called titanium sub-oxides (TinO2n-1, 4 < n < 9), are a series of electrically conducting ceramic materials. The synthesis and applications of these materials have recently attracted tremendous attention because of their applications in a number of existing and emerging areas. Titanium sub-oxides are generally synthesized through the reduction of titanium dioxide using hydrogen, carbon, metals or metal hydrides as reduction agents. More recently, the synthesis of nanostructured titanium sub-oxides has been making progress through optimizing thermal reduction processes or using new titanium-containing precursors. Titanium sub-oxides have attractive properties such as electrical conductivity, corrosion resistance and optical properties. Titanium sub-oxides have played important roles in a number of areas such as conducting materials, fuel cells and organic degradation. Titanium sub-oxides also show promising applications in batteries, solar energy, coatings and electronic and optoelectronic devices. Titanium sub-oxides are expected to become more important materials in the future. In this review, the recent progress in the synthesis methods and applications of titanium sub-oxides in the existing and emerging areas are reviewed.

Polyvinylpyrrolidone/TiO2 composites' preparation via sol-gel procedure furthered with non-enzymatic glucose sensing and antibacterial effectiveness

An amperometric non-enzymatic glucose sensing based on polyvinylpyrrolidone and titanium dioxide nanocomposites (PVP-TiO2 NCs) fabricated over stainless-steel (SS) electrode was experimented. The electrode was fabricated of PVP-TiO2 NCs onto SS surface through drop casting coating. The NCs and the electrode were analyzed using Fourier transform infrared (FTIR) and UV-visible (UV-Vis) spectroscopy, X-ray diffraction spectra (XRD), X-ray photoelectron spectra (XPS), particle analyzer, scanning electron microscopy (SEM), EDS and transmission electron microscopy (TEM) and Brunauer-Emmett-Teller (BET) analysis for surface. For electrochemical investigation, cyclic voltammetry, electrochemical impedance spectra, including Nyquist plots and Bode plots, and chronoamperometry were adopted. PVP-TiO2/SS-modified electrode manifested high sensitivity of 360.13 µA/mM.cm2, lower detection limit of 756.8 µM and 0 to 13 mM linear range with regression coefficient of R2 = 0.992. The electrode exhibited high stability with good anti-interference tendency against fructose, uric acid, ascorbic acid and sucrose. The modified electrode also performed well in real sample glucose detection. Further, PVP-TiO2 NCs performed appreciably toward antibacterial studies against some Gram-positive and Gram-negative deleterious bacteria, Escherichia coli, Klebsiella pneumoniae, Staphylococcus aureus, Shigella flexneri microbes.

Recent Advancements in TiO2 Nanostructures: Sustainable Synthesis and Gas Sensing

The search for sustainable technology-driven advancements in material synthesis is a new norm, which ensures a low impact on the environment, production cost, and workers' health. In this context, non-toxic, non-hazardous, and low-cost materials and their synthesis methods are integrated to compete with existing physical and chemical methods. From this perspective, titanium oxide (TiO₂) is one of the fascinating materials because of its non-toxicity, biocompatibility, and potential of growing by sustainable methods. Accordingly, TiO₂ is extensively used in gas-sensing devices. Yet, many TiO₂ nanostructures are still synthesized with a lack of mindfulness of environmental impact and sustainable methods, which results in a serious burden on practical commercialization. This review provides a general outline of the advantages and disadvantages of conventional and sustainable methods of TiO₂ preparation. Additionally, a detailed discussion on sustainable growth methods for green synthesis is included. Furthermore, gas-sensing applications and approaches to improve the key functionality of sensors, including response time, recovery time, repeatability, and stability, are discussed in detail in the latter parts of the review. At the end, a concluding discussion is included to provide guidelines for the selection of sustainable synthesis methods and techniques to improve the gas-sensing properties of TiO₂.

MRC-5 Human Lung Fibroblasts Alleviate the Genotoxic Effect of Fe-N Co-Doped Titanium Dioxide Nanoparticles through an OGG1/2-Dependent Reparatory Mechanism

The current study was focused on the potential of pure P25 TiO2 nanoparticles (NPs) and Fe(1%)-N co-doped P25 TiO2 NPs to induce cyto- and genotoxic effects in MRC-5 human pulmonary fibroblasts. The oxidative lesions of P25 NPs were reflected in the amount of 8-hydroxydeoxyguanosine accumulated in DNA and the lysosomal damage produced, but iron-doping partially suppressed these effects. However, neither P25 nor Fe(1%)-N co-doped P25 NPs had such a serious effect of inducing DNA fragmentation or activating apoptosis signaling. Moreover, oxo-guanine glycosylase 1/2, a key enzyme of the base excision repair mechanism, was overexpressed in response to the oxidative DNA deterioration induced by P25 and P25-Fe(1%)-N NPs.

Room-temperature ammonia gas sensing via Au nanoparticle-decorated TiO2 nanosheets

A high-performance gas sensor operating at room temperature is always favourable since it simplifies the device fabrication and lowers the operating power by eliminating a heater. Herein, we fabricated the ammonia (NH₃) gas sensor by using Au nanoparticle-decorated TiO₂ nanosheets, which were synthesized via two distinct processes: (1) preparation of monolayer TiO₂ nanosheets through flux growth and a subsequent chemical exfoliation and (2) decoration of Au nanoparticles on the TiO₂ nanosheets via hydrothermal method. Based on the morphological, compositional, crystallographic, and surface characteristics of this low-dimensional nano-heterostructured material, its temperature- and concentration-dependent NH₃ gas-sensing properties were investigated. A high response of ~ 2.8 was obtained at room temperature under 20 ppm NH₃ gas concentration by decorating Au nanoparticles onto the surface of TiO₂ nanosheets, which generated oxygen defects and induced spillover effect as well.

Electrochemical Immunosensor for the Determination of Antibodies against Prostate-Specific Antigen Based on ZnO Nanostructures

In this study, ZnO nanostructures with different types of morphologies and particle sizes were evaluated and applied for the development of an immunosensor. The first material was composed of spherical, polydisperse nanostructures with a particle size in the range of 10–160 nm. The second was made up of more compact rod-like spherical nanostructures with the diameter of these rods in the range of 50–400 nm, and approximately 98% of the particles were in the range of 20–70 nm. The last sample of ZnO was made up of rod-shaped particles with a diameter of 10–80 nm. These ZnO nanostructures were mixed with Nafion solution and drop-casted onto screen-printed carbon electrodes (SPCE), followed by a further immobilization of the prostate-specific antigen (PSA). The affinity interaction of PSA with monoclonal antibodies against PSA (anti-PSA) was evaluated using the differential pulse voltammetry technique. The limit of detection and limit of quantification of anti-PSA were determined as 1.35 nM and 4.08 nM for compact rod-shaped spherical ZnO nanostructures, and 2.36 nM and 7.15 nM for rod-shaped ZnO nanostructures, respectively.

Molecularly imprinted polymers for the recognition of biomarkers of certain neurodegenerative diseases

The appearance of the biomarkers in body fluids like blood, urine, saliva, tears, etc. can be used for the identification of many diseases. This article aimed to summarize the studies about electrochemical biosensors with molecularly imprinted polymers as sensitive and selective layers on the electrode to detect protein-based biomarkers of such neurodegenerative diseases as Alzheimer's disease, Parkinson's disease, and stress. The main attention in this article is focused on the detection methods of amyloid-β oligomers and p-Tau which are representative biomarkers for Alzheimer's disease, α-synuclein as the biomarker of Parkinson's disease, and α-amylase and lysozyme as the biomarkers of stress using molecular imprinting technology. The research methods, the application of different electrodes, the influence of the polymers, and the established detection limits are reviewed and compared.

A review on identification, quantification, and transformation of active species in SCR by EPR spectroscopy

Electron paramagnetic resonance (EPR) is the only technique that provides direct detection of free radicals and samples that contain unpaired electrons. Thus, EPR had an important potential application in the field of selective catalytic reduction of nitrogen oxide (SCR). For the first time, this work reviewed recent developments of EPR in charactering SCR. First, qualitative analysis focused on recognizing Cu, Fe, V, Ti, Mn, and free-radical (oxygen vacancy and superoxide radical) species. Second, quantification of the active species was obtained by a double-integral and calibration method. Third, the active species evolved because of different thermal treatments and redox-thermal processes under reductants (NH₃ and NO). The coordination information of the active species in catalysts and their effects on SCR performances were concluded from mechanism viewpoints. Finally, potential perspectives were put forward for EPR developments in characterizing the SCR processes in the future. After all, EPR characterization will help to have a deep understanding of structure-activity relationship in one catalyst.

Green production of titanium dioxide nanometric particles through electrolytic anodic dissolution of titanium metal

Nanometric titanium derivatives such as hydroxide and dioxide compounds have a great attention because they are significant industrial material of commercial importance and applications in photocatalyst, semiconductors, and wastewater treatment. The present investigation gives the results of anodic dissolution preparation of titanium hydroxide nanometric particles followed by calcination for complete conversion to nanometric titanium dioxide product. The optimum conditions for the anodic dissolution of titanium metal were pH 4, C.D. 65 mA/cm², 25 °C, 150 rpm, electrode gap distance 3 cm, and NaCl 3 g/l for electrolysis time 240 min and thermally calcinated at 600 °C for 240 min., to reach complete conversion to anatase titanium dioxide nanopowder of main particles size of 77 nm with major percentage of 70%. Chemical and physical characterizations were carried out for evaluation of the obtained products including transmission electron microscope, EDX, XRD, and the scanning advanced electronic diffraction pattern. Preliminary economic indicators were calculated to show that the capital cost of the plant is $1.613 million, with annual operating cost of $0.915 million which means the required investment is $2.528 million. The operating cost for the production of nanometric anatase TiO₂ is $30.5/kg with depreciation excluding the land price.

Atom-to-Device Simulation of MoO3/Si Heterojunction Solar Cell

Metal oxides are commonly used in optoelectronic devices due to their transparency and excellent electrical conductivity. Based on its physical properties, each metal oxide serves as the foundation for a unique device. In this study, we opt to determine and assess the physical properties of MoO₃ metal oxide. Accordingly, the optical and electronic parameters of MoO₃ are evaluated using DFT (Density Functional Theory), and PBE and HSE06 functionals were mainly used in the calculation. It was found that the band structure of MoO₃ calculated using PBE and HSE06 exhibited indirect semiconductor properties with the same line quality. Its band gap was 3.027 eV in HSE06 and 2.12 eV in PBE. Electrons and holes had effective masses and mobilities of 0.06673, -0.10084, 3811.11 cm²V^-1s^-1 and 1630.39 cm²V^-1s^-1, respectively. In addition, the simulation determined the dependence of the real and imaginary components of the complex refractive index and permittivity of MoO₃ on the wavelength of light, and a value of 58 corresponds to the relative permittivity. MoO₃ has a refractive index of between 1.5 and 3 in the visible spectrum, which can therefore be used as an anti-reflection layer for solar cells made from silicon. In addition, based on the semiconducting properties of MoO₃, it was estimated that it could serve as an emitter layer for a solar cell containing silicon. In this work, we calculated the photoelectric parameters of the MoO3/Si heterojunction solar cell using Sentaurus TCAD (Technology Computing Aided Design). According to the obtained results, the efficiency of the MoO₃/Si solar cell with a MoO₃ layer thickness of 100 nm and a Si layer thickness of 9 nm is 8.8%, which is 1.24% greater than the efficiency of a homojunction silicon-based solar cell of the same size. The greatest short-circuit current for a MoO₃/Si heterojunction solar cell was observed at a MoO₃ layer thickness of 60 nm, which was determined by studying the dependency of the heterojunction short-circuit current on the thickness of the MoO₃ layer.

Magnéli phase titanium sub-oxides synthesis, fabrication and its application for environmental remediation: Current status and prospect

Sub-stoichiometric titanium oxide, also called titanium suboxides (TSO), had been a focus of research for many decades with a chemical composition of Ti_nO_2n-1 (n ≥ 1). It has a unique oxygen-deficient crystal structure which provides it an outstanding electrical conductivity and high corrosion resistance similar to ceramic materials. High electrical conductivity and ability to sustain in adverse media make these phases a point of attention for researchers in energy storage and environmental remediation applications. The Magnéli phase-based reactive electroconductive membranes (REM) and electrodes have demonstrated the electrochemical oxidation of pollutants in the water in flow-through and flow by configuration. Additionally, it has also shown its potential for visible light photochemical degradation as well. This review attempts to summarize state of the art in various Magnéli phases materials synthesis routes and their electrochemical and photochemical ability for environmental application. The manuscript introduces the Magnéli phase, its crystal structure, and catalytic properties, followed by the recent development in synthesis methods from diverse titanium sources, notably TiO₂ through thermal reduction. The various fabrication methods for Magnéli phase-base REMs and electrodes have also been summarized. Furthermore, the article discussed the environmental remediations via electrochemical and photochemical advanced oxidation processes. Additionally, the hybrid technology with REMs and electrodes is used to counter membrane biofouling and develop electrochemical sensing devices for the pollutants. The Magnéli phase materials have a bright future for both electrochemical and photochemical advanced oxidation of emerging contaminants in water and wastewater treatment.

Conducting Polymers for the Design of Tactile Sensors

This paper provides an overview of the application of conducting polymers (CPs) used in the design of tactile sensors. While conducting polymers can be used as a base in a variety of forms, such as films, particles, matrices, and fillers, the CPs generally remain the same. This paper, first, discusses the chemical and physical properties of conducting polymers. Next, it discusses how these polymers might be involved in the conversion of mechanical effects (such as pressure, force, tension, mass, displacement, deformation, torque, crack, creep, and others) into a change in electrical resistance through a charge transfer mechanism for tactile sensing. Polypyrrole, polyaniline, poly(3,4-ethylenedioxythiophene), polydimethylsiloxane, and polyacetylene, as well as application examples of conducting polymers in tactile sensors, are overviewed. Attention is paid to the additives used in tactile sensor development, together with conducting polymers. There is a long list of additives and composites, used for different purposes, namely: cotton, polyurethane, PDMS, fabric, Ecoflex, Velostat, MXenes, and different forms of carbon such as graphene, MWCNT, etc. Some design aspects of the tactile sensor are highlighted. The charge transfer and operation principles of tactile sensors are discussed. Finally, some methods which have been applied for the design of sensors based on conductive polymers, are reviewed and discussed.

Development of molecularly imprinted polymer based phase boundaries for sensors design (review)

Achievements in polymer chemistry enables to design artificial phase boundaries modified by imprints of selected molecules and some larger structures. These structures seem very useful for the design of new materials suitable for affinity chromatography and sensors. In this review, we are overviewing the synthesis of molecularly imprinted polymers (MIPs) and the applicability of these MIPs in the design of affinity sensors. Such MIP-based layers or particles can be used as analyte-recognizing parts for sensors and in some cases they can replace very expensive compounds (e.g.: antibodies, receptors etc.), which are recognizing analyte. Many different polymers can be used for the formation of MIPs, but conducing polymers shows the most attractive capabilities for molecular-imprinting by various chemical compounds. Therefore, the application of conducting polymers (e.g.: polypyrrole, polyaniline, polythiophene, poly(3,4-ethylenedioxythiophene), and ortho-phenylenediamine) seems very promising. Polypyrrole is one of the most suitable for the development of MIP-based structures with molecular imprints by analytes of various molecular weights. Overoxiation of polypyrrole enables to increase the selectivity of polypyrrole-based MIPs. Methods used for the synthesis of conducting polymer based MIPs are overviewed. Some methods, which are applied for the transduction of analytical signal, are discussed, and challenges and new trends in MIP-technology are foreseen.

Advances and emerging challenges in MXenes and their nanocomposites for biosensing applications

Two-dimensional materials have unique properties and their better functionality has created new paradigms in the field of sensing. Over the past decade, a new family of 2D materials known as MXenes has emerged as a promising material for numerous applications, including biosensing. Their metallic conductivity, rich surface chemistry, hydrophilicity, good biocompatibility, and high anchoring capacity for biomaterials make them an attractive candidate to detect a variety of analytes. Despite such notable properties, there are certain limitations associated with them. This review aims to present a detailed survey of MXene's synthesis; in particular, their superiority in the field of biosensing as compared to other 2D materials is addressed. Their low oxidative stability is still an open challenge, and recent investigations on MXene's oxidation are summarized. The hexagonal stacking network of MXenes acts as a distinctive matrix to load nanoparticles, and the embedded nanoparticles can bind an excess number of biomolecules (e.g., antibodies) thereby improving biosensor performance. We will also discuss the synthesis and corresponding performance of MXenes nanocomposites with noble metal nanoparticles and magnetic nanoparticles. Furthermore, Nb and Ti2C-based MXenes, and Ti3C2-MXene sandwich immunoassays are also reviewed in view of their importance. Different aspects and challenges associated with MXenes (from their synthesis to final applications) and the future perspectives described give new directions to fabricate novel biosensors.

Assessment of TiO2 Nanoparticle Impact on Surface Morphology of Chinese Hamster Ovary Cells

The process of nanoparticles entering the cells of living organisms is an important step in understanding the influence of nanoparticles on biological processes. The interaction of nanoparticles with the cell membrane is the first step in the penetration of nanoparticles into cells; however, the penetration mechanism is not yet fully understood. This work reported the study of the interaction between TiO₂ nanoparticles (TiO₂-NPs) and Chinese hamster ovary (CHO) cells using an in vitro model. The characterization of crystalline phases of TiO₂ NPs was evaluated by transmission electron microscopy (TEM), X-ray diffraction (XRD) spectrum, and atomic force microscopy (AFM). Interaction of these TiO₂ nanoparticles (TiO₂- NPs) with the CHO cell membrane was investigated using atomic force microscopy (AFM) and Raman spectroscopy. The XRD analysis result showed that the structure of the TiO₂ particles was in the rutile phase with a crystallite size of 60 nm, while the AFM result showed that the particle size distribution had two peaks with 12.1 nm and 60.5 nm. The TEM analysis confirmed the rutile phase of TiO₂ powder. Our study showed that exposure of CHO cells to TiO₂-NPs caused morphological changes in the cell membranes and influenced the viability of cells. The TiO₂-NPs impacted the cell membrane surface; images obtained by AFM revealed an ‘ultra structure‘ with increased roughness and pits on the surface of the membrane. The depth of the pits varied in the range of 40–80 nm. The maximal depth of the pits after the treatment with TiO₂-NPs was 100% higher than the control values. It is assumed that these pits were caveolae participating in the endocytosis of TiO₂-NPs. The research results suggest that the higher maximal depth of the pits after the exposure of TiO₂-NPs was determined by the interaction of these TiO₂-NPs with the cell’s plasma membrane. Moreover, some of pits may have been due to plasma membrane damage (hole) caused by the interaction of TiO₂-NPs with membrane constituents. The analysis of AFM images demonstrated that the membrane roughness was increased with exposure time of the cells to TiO₂-NPs dose. The average roughness after the treatment for 60 min with TiO₂-NPs increased from 40 nm to 78 nm. The investigation of the membrane by Raman spectroscopy enabled us to conclude that TiO₂-NPs interacted with cell proteins, modified their conformation, and potentially influenced the structural damage of the plasma membrane.

Biosensors Based on Bio-Functionalized Semiconducting Metal Oxides

Immobilization of biomaterials is a very important task in the development of biofuel cells and biosensors. Some semiconducting metal-oxide-based supporting materials can be used in these bioelectronics-based devices. In this article, we are reviewing some functionalization methods that are applied for the immobilization of biomaterials. The most significant attention is paid to the immobilization of biomolecules on the surface of semiconducting metal oxides. The improvement of biomaterials immobilization on metal oxides and analytical performance of biosensors by coatings based on conducting polymers, self-assembled monolayers and lipid membranes is discussed.

Gas Sensors Based on Titanium Oxides (Review)

Nanostructured titanium compounds have recently been applied in the design of gas sensors. Among titanium compounds, titanium oxides (TiO2) are the most frequently used in gas sensing devices. Therefore, in this review, we are paying significant attention to the variety of allotropic modifications of titanium oxides, which include anatase, rutile, brukite. Very recently, the applicability of non-stoichiometric titanium oxide (TiO2−x)-based layers for the design of gas sensors was demonstrated. For this reason, in this review, we are addressing some research related to the formation of non-stoichiometric titanium oxide (TiO2−x) and Magnéli phase (TinO2n−1)-based layers suitable for sensor design. The most promising titanium compounds and hetero- and nano-structures based on these compounds are discussed. It is also outlined that during the past decade, many new strategies for the synthesis of TiO2 and conducting polymer-based composite materials were developed, which have found some specific application areas. Therefore, in this review, we are highlighting how specific formation methods, which can be used for the formation of TiO2 and conducting polymer composites, can be applied to tune composite characteristics that are leading towards advanced applications in these specific technological fields. The possibility to tune the sensitivity and selectivity of titanium compound-based sensing layers is addressed. In this review, some other recent reviews related to the development of sensors based on titanium oxides are overviewed. Some designs of titanium-based nanomaterials used for the development of sensors are outlined.

Tunable TiO2-BN-Pd nanofibers by combining electrospinning and atomic layer deposition to enhance photodegradation of acetaminophen

The demand for fresh and clean water sources is increasing globally, and there is a need to develop novel routes to eliminate micropollutants and other harmful species from water. Photocatalysis is a promising alternative green technology that has shown great performance in the degradation of persistent pollutants. Titanium dioxide is the most used catalyst owing to its attractive physico-chemical properties, but this semiconductor presents limitations in the photocatalysis process due to the high band gap and the fast recombination of the photogenerated carriers. Herein, a novel photocatalyst has been developed, based on titanium dioxide nanofibers (TiO2 NFs) synthesized by electrospinning. The TiO2 NFs were coated by atomic layer deposition (ALD) to grow boron nitride (BN) and palladium (Pd) on their surface. The UV-Vis spectroscopy measurements confirmed the increase of the band gap and the extension of the spectral response to the visible range. The obtained TiO2/BN/Pd nanofibers were then tested for photocatalysis, and showed a drastic increase of acetaminophen (ACT) degradation (>90%), compared to only 20% degradation obtained with pure TiO2 after 4 h of visible light irradiation. The high photocatalytic activity was attributed to the good dispersion of Pd NPs on TiO2-BN nanofibers, leading to a higher transfer of photoexcited hole carriers and a decrease of photogenerated electron-charge recombination. To confirm its reusability, recycling tests on the hybrid photocatalyst TiO2/BN/Pd have been performed, showing a good stability over 5 cycles under UV and visible light. In addition, toxicity tests as well as quenching tests were carried out to check the toxicity of the byproducts formed and to determine active species responsible for the degradation. The results presented in this work demonstrate the potential of TiO2/BN/Pd nanomaterials, and open new prospects for the preparation of tunable photocatalysts.

Electrochemically Deposited Molecularly Imprinted Polymer-Based Sensors

This review is dedicated to the development of molecularly imprinted polymers (MIPs) and the application of MIPs in sensor design. MIP-based biological recognition parts can replace receptors or antibodies, which are rather expensive. Conducting polymers show unique properties that are applicable in sensor design. Therefore, MIP-based conducting polymers, including polypyrrole, polythiophene, poly(3,4-ethylenedioxythiophene), polyaniline and ortho-phenylenediamine are frequently applied in sensor design. Some other materials that can be molecularly imprinted are also overviewed in this review. Among many imprintable materials conducting polymer, polypyrrole is one of the most suitable for molecular imprinting of various targets ranging from small organics up to rather large proteins. Some attention in this review is dedicated to overview methods applied to design MIP-based sensing structures. Some attention is dedicated to the physicochemical methods applied for the transduction of analytical signals. Expected new trends and horizons in the application of MIP-based structures are also discussed.

Capacitive and Conductometric Type Dual-Mode Relative Humidity Sensor Based on 5,10,15,20-tetra Phenyl Porphyrinato Nickel (II) (TPPNi)

(1) Background: A quest for a highly sensitive and reliable humidity monitoring system for a diverse variety of applications is quite vital. Specifically, the ever-increasing demand of humidity sensors in applications ranging from agriculture to healthcare equipment (to cater the current demand of COVID-19 ventilation systems), calls for a selection of suitable humidity sensing material. (2) Methods: In the present study, the TPPNi macromolecule has been synthesized by using a microwave-assisted synthesis process. The layer structure of the fabricated humidity sensor (Al/TPPNi/Al) consists of pair of planar 120 nm thin aluminum (Al) electrodes (deposited by thermal evaporation) and ~160 nm facile spin-coated solution-processable organic TPPNi as an active layer between the ~40 µm electrode gap. (3) Results: Electrical properties (capacitance and impedance) of sensors were found to be substantially sensitive not only on relative humidity but also on the frequency of the input bias signal. The proposed sensor exhibits multimode (capacitive and conductometric) operation with significantly higher sensitivity ~146.17 pF/%RH at 500 Hz and 48.23 kΩ/%RH at 1 kHz. (4) Conclusions: The developed Al/TPPNi/Al surface type humidity sensor’s much-improved detecting properties along with reasonable dynamic range and response time suggest that it could be effective for continuous humidity monitoring in multi environmental applications.

Effect of temperature and humidity on the sensing performance of TiO2nanowire-based ethanol vapor sensors

In this paper, we study the influence of two key factors, temperature, and humidity, on gas sensors based on titanium dioxide nanowires synthesized at 4 different temperatures and with different morphology. The samples' structure are investigated using SEM, XRD and FTIR analysis. The effects of humidity and temperature are studied by measuring the resistance and gas response when exposed to ethanol. At room temperature, we observed a 15% sensitivity response to 100 ppm of ethanol vapor and by increasing the operating temperature up to 180 °C, the response is enhanced by two orders of magnitude. The best operating temperature for the highest gas response is found to be around 180 °C. Also, it was observed that every nanowire morphology has its own optimum operating temperature. The resistance of sensors is increased at higher Relative Humidity (RH). Besides, the response to ethanol vapor experiences a gradual increase when the RH rises from 10% to 60%. On the other hand, from 60% to 90% RH the gas response decreases gradually due to different mechanisms of interaction of the TiO₂with H₂O and ethanol molecules.

Molecular Imprinting Technology for Determination of Uric Acid

The review focuses on the overview of electrochemical sensors based on molecularly imprinted polymers (MIPs) for the determination of uric acid. The importance of robust and precise determination of uric acid is highlighted, a short description of the principles of molecular imprinting technology is presented, and advantages over the others affinity-based analytical methods are discussed. The review is mainly concerned with the electro-analytical methods like cyclic voltammetry, electrochemical impedance spectroscopy, amperometry, etc. Moreover, there are some scattered notes to the other electrochemistry-related analytical methods, which are capable of providing additional information and to solve some challenges that are not achievable using standard electrochemical methods. The significance of these overviewed methods is highlighted. The overview of the research that is employing MIPs imprinted with uric acid is mainly targeted to address these topics: (i) type of polymers, which are used to design uric acid imprint structures; (ii) types of working electrodes and/or other parts of signal transducing systems applied for the registration of analytical signal; (iii) the description of the uric acid extraction procedures applied for the design of final MIP-structure; (iv) advantages and disadvantages of electrochemical methods and other signal transducing methods used for the registration of the analytical signal; (vi) overview of types of interfering molecules, which were analyzed to evaluate the selectivity; (vi) comparison of analytical characteristics such as linear range, limits of detection and quantification, reusability, reproducibility, repeatability, and stability. Some insights in future development of uric acid sensors are discussed in this review.

Extraction–Pyrolytic Method for TiO2 Polymorphs Production

The unique properties and numerous applications of nanocrystalline titanium dioxide (TiO2) are stimulating research on improving the existing and developing new titanium dioxide synthesis methods. In this work, we demonstrate for the first time the possibilities of the extraction–pyrolytic method (EPM) for the production of nanocrystalline TiO2 powders. A titanium-containing precursor (extract) was prepared by liquid–liquid extraction using valeric acid C4H9COOH without diluent as an extractant. Simultaneous thermogravimetric analysis and differential scanning calorimetry (TGA–DSC), as well as the Fourier-transform infrared (FTIR) spectroscopy were used to determine the temperature conditions to fabricate TiO2 powders free of organic impurities. The produced materials were also characterized by X-ray diffraction (XRD) analysis and transmission electron microscopy (TEM). The results showed the possibility of the fabrication of storage-stable liquid titanium (IV)-containing precursor, which provided nanocrystalline TiO2 powders. It was established that the EPM permits the production of both monophase (anatase polymorph or rutile polymorph) and biphase (mixed anatase–rutile polymorphs), impurity-free nanocrystalline TiO2 powders. For comparison, TiO2 powders were also produced by the precipitation method. The results presented in this study could serve as a solid basis for further developing the EPM for the cheap and simple production of nanocrystalline TiO2-based materials in the form of doped nanocrystalline powders, thin films, and composite materials.

Advances in Molecularly Imprinted Polymers Based Affinity Sensors (Review)

Recent challenges in biomedical diagnostics show that the development of rapid affinity sensors is very important issue. Therefore, in this review we are aiming to outline the most important directions of affinity sensors where polymer-based semiconducting materials are applied. Progress in formation and development of such materials is overviewed and discussed. Some applicability aspects of conducting polymers in the design of affinity sensors are presented. The main attention is focused on bioanalytical application of conducting polymers such as polypyrrole, polyaniline, polythiophene and poly(3,4-ethylenedioxythiophene) ortho-phenylenediamine. In addition, some other polymers and inorganic materials that are suitable for molecular imprinting technology are also overviewed. Polymerization techniques, which are the most suitable for the development of composite structures suitable for affinity sensors are presented. Analytical signal transduction methods applied in affinity sensors based on polymer-based semiconducting materials are discussed. In this review the most attention is focused on the development and application of molecularly imprinted polymer-based structures, which can replace antibodies, receptors, and many others expensive affinity reagents. The applicability of electrochromic polymers in affinity sensor design is envisaged. Sufficient biocompatibility of some conducting polymers enables to apply them as "stealth coatings" in the future implantable affinity-sensors. Some new perspectives and trends in analytical application of polymer-based semiconducting materials are highlighted.

Review of Functional Treatments for Modified Wood

Wood modification is now widely recognized as offering enhanced properties of wood and overcoming issues such as dimensional instability and biodegradability which affect natural wood. Typical wood modification systems use chemical modification, impregnation modification or thermal modification, and these vary in the properties achieved. As control and understanding of the wood modification systems has progressed, further opportunities have arisen to add extra functionalities to the modified wood. These include UV stabilisation, fire retardancy, or enhanced suitability for paints and coatings. Thus, wood may become a multi-functional material through a series of modifications, treatments or reactions, to create a high-performance material with previously impossible properties. In this paper we review systems that combine the well-established wood modification procedures with secondary techniques or modifications to deliver emerging technologies with multi-functionality. The new applications targeted using this additional functionality are diverse and range from increased electrical conductivity, creation of sensors or responsive materials, improvement of wellbeing in the built environment, and enhanced fire and flame protection. We identified two parallel and connected themes: (1) the functionalisation of modified timber and (2) the modification of timber to provide (multi)-functionality. A wide range of nanotechnology concepts have been harnessed by this new generation of wood modifications and wood treatments. As this field is rapidly expanding, we also include within the review trends from current research in order to gauge the state of the art, and likely direction of travel of the industry.

Charge Transfer and Biocompatibility Aspects in Conducting Polymer-Based Enzymatic Biosensors and Biofuel Cells

Charge transfer (CT) is a very important issue in the design of biosensors and biofuel cells. Some nanomaterials can be applied to facilitate the CT in these bioelectronics-based devices. In this review, we overview some CT mechanisms and/or pathways that are the most frequently established between redox enzymes and electrodes. Facilitation of indirect CT by the application of some nanomaterials is frequently applied in electrochemical enzymatic biosensors and biofuel cells. More sophisticated and still rather rarely observed is direct charge transfer (DCT), which is often addressed as direct electron transfer (DET), therefore, DCT/DET is also targeted and discussed in this review. The application of conducting polymers (CPs) for the immobilization of enzymes and facilitation of charge transfer during the design of biosensors and biofuel cells are overviewed. Significant attention is paid to various ways of synthesis and application of conducting polymers such as polyaniline, polypyrrole, polythiophene poly(3,4-ethylenedioxythiophene). Some DCT/DET mechanisms in CP-based sensors and biosensors are discussed, taking into account that not only charge transfer via electrons, but also charge transfer via holes can play a crucial role in the design of bioelectronics-based devices. Biocompatibility aspects of CPs, which provides important advantages essential for implantable bioelectronics, are discussed.

Ultraviolet Light Treatment of Titanium Enhances Attachment, Adhesion, and Retention of Human Oral Epithelial Cells via Decarbonization

Early establishment of soft-tissue adhesion and seal at the transmucosal and transcutaneous surface of implants is crucial to prevent infection and ensure the long-term stability and function of implants. Herein, we tested the hypothesis that treatment of titanium with ultraviolet (UV) light would enhance its interaction with epithelial cells. X-ray spectroscopy showed that UV treatment significantly reduced the atomic percentage of surface carbon on titanium from 46.1% to 28.6%. Peak fitting analysis revealed that, among the known adventitious carbon contaminants, C-C and C=O groups were significantly reduced after UV treatment, while other groups were increased or unchanged in percentage. UV-treated titanium attracted higher numbers of human epithelial cells than untreated titanium and allowed more rapid cell spread. Hemi-desmosome-related molecules, integrin β4 and laminin-5, were upregulated at the gene and protein levels in the cells on UV-treated surfaces. The result of the detachment test revealed twice as many cells remaining adherent on UV-treated than untreated titanium. The enhanced cellular affinity of UV-treated titanium was equivalent to laminin-5 coating of titanium. These data indicated that UV treatment of titanium enhanced the attachment, adhesion, and retention of human epithelial cells associated with disproportional removal of adventitious carbon contamination, providing a new strategy to improve soft-tissue integration with implant devices.

Conducting Polymers in the Design of Biosensors and Biofuel Cells

Fast and sensitive determination of biologically active compounds is very important in biomedical diagnostics, the food and beverage industry, and environmental analysis. In this review, the most promising directions in analytical application of conducting polymers (CPs) are outlined. Up to now polyaniline, polypyrrole, polythiophene, and poly(3,4-ethylenedioxythiophene) are the most frequently used CPs in the design of sensors and biosensors; therefore, in this review, main attention is paid to these conducting polymers. The most popular polymerization methods applied for the formation of conducting polymer layers are discussed. The applicability of polypyrrole-based functional layers in the design of electrochemical biosensors and biofuel cells is highlighted. Some signal transduction mechanisms in CP-based sensors and biosensors are discussed. Biocompatibility-related aspects of some conducting polymers are overviewed and some insights into the application of CP-based coatings for the design of implantable sensors and biofuel cells are addressed. New trends and perspectives in the development of sensors based on CPs and their composites with other materials are discussed.