A comprehensive review of techniques for biofunctionalization of titanium

Characterization of aTiO2 surfaces functionalized with CAP-p15 peptide

Functionalization of Titanium implants using adequate organic molecules is a proposed method to accelerate the osteointegration process, which relates to topographical, chemical, mechanical, and physical features. This study aimed to assess the potential of a peptide derived from cementum attachment protein (CAP-p15) adsorbed onto aTiO2 surfaces to promote the deposition of calcium phosphate (CaP) minerals and its impact on the adhesion and viability of human periodontal ligament cells (hPDLCs). aTiO2 surfaces were synthesized by magnetron sputtering technique. The CAP-p15 peptide was physically attached to aTiO2 surfaces and characterized by atomic force microscopy, fluorescence microscopy, and water contact angle measurement. We performed in vitro calcium phosphate nucleation assays using an artificial saliva solution (pH 7.4) to simulate the oral environment. morphological and chemical characterization of the deposits were evaluated by scanning electronic microscopy (SEM) and spectroscopy molecular techniques (Raman Spectroscopy, ATR-FTIR). The aTiO2 surfaces biofunctionalized with CAP-p15 were also analyzed for hPDLCs attachment, proliferation, and in vitro scratch-healing assay. The results let us see that the homogeneous amorphous titanium oxide coating was 70 nanometers thick. The CAP-p15 (1 μg/mL) displayed the ability to adsorb onto the aTiO2 surface, increasing the roughness and maintaining the hydrophilicity of the aTiO2 surfaces. The physical adsorption of CAP-p15 onto the aTiO2 surfaces promoted the precipitation of a uniform layer of crystals with a flake-like morphology and a Ca/P ratio of 1.79. According to spectroscopy molecular analysis, these crystalline deposits correspond to carbonated hydroxyapatite. Regarding cell behavior, the biofunctionalized aTiO2 surfaces improved the adhesion of hPDLCs after 24 h of cell culture, achieving 3.4-fold when compared to pristine surfaces. Moreover, there was an increase in cell proliferation and cell migration processes. Physical adsorption of CAP-p15 onto aTiO2 surfaces enhanced the formation of carbonate hydroxyapatite crystals and promoted the proliferation and migration of human periodontal ligament-derived cells in in vitro studies. This experimental model using the novel bioactive peptide CAP-p15 could be used as an alternative to increasing the osseointegration process of implants.

Designing a highly near infrared-reflective black nanoparticles for autonomous driving based on the refractive index and principle

HYPOTHESIS

The development of highly NIR reflective black single-shell hollow nanoparticles (BSS-HNPs) can overcome the Light Detection and Ranging (LiDAR) sensor limitations of dark-tone materials. The crystalline phase of TiO2 and the refractive index can be controlled by calcination temperature. The formation of hollow structure and the refractive index is expected to simultaneously increase the light reflection and LiDAR detectability.

EXPERIMENTS

The BSS-HNPs are synthesized using the sol-gel method, calcination, NaBH4 reduction, and etching to form a hollow structure with true blackness. The computational bandgap calculation is conducted to determine the bandgap energy (Eg) of the white and black TiO2 with different crystalline structures. The blackness of the as-synthesized materials is determined by the Commission on Illumination (CIE) L*a*b* color system.

FINDINGS

The hydrophilic nature of BSS-HNPs enables the formulation of hydrophilic paints, allowing the mono-layer coating. With the synergistic effects of hollow structure and the refractive index, BSS-HNPs manifested superb NIR reflectance at LiDAR detection wavelengths. The high detectability, blackness, and hollow structure of BSS-HNPs can expand the variety of LiDAR-detectable dark-tone materials.

Strontium-loaded 3D intramedullary nail titanium implant for critical-sized femoral defect in rabbits

The treatment of critical-sized bone defects has long been a major problem for surgeons. In this study, an intramedullary nail shaped three-dimensional (3D)-printed porous titanium implant that is capable of releasing strontium ions was developed through a simple and cost-effective surface modification technique. The feasibility of this implant as a stand-alone solution was evaluated using a rabbit's segmental diaphyseal as a defect model. The strontium-loaded implant exhibited a favorable environment for cell adhesion, and mechanical properties that were commensurate with those of a rabbit's cortical bone. Radiographic, biomechanical, and histological analyses revealed a significantly higher amount of bone ingrowth and superior bone-bonding strength in the strontium-loaded implant when compared to an untreated porous titanium implant. Furthermore, one-year histological observations revealed that the strontium-loaded implant preserved the native-like diaphyseal bone structure without failure. These findings suggest that strontium-releasing 3D-printed titanium implants have the clinical potential to induce the early and efficient repair of critical-sized, load-bearing bone defects.

Surface modification of titanium implants with Mg-containing coatings to promote osseointegration

Titanium (Ti) and Ti alloys are commonly used in dental implants, which have good biocompatibility, mechanical strength, processability, and corrosion resistance. However, the surface inertia of Ti implants leads to delayed integration of Ti and new bone, as well as problems such as aseptic loosening and inadequate osseointegration. Magnesium (Mg) ions can promote bone regeneration, and many studies have used Mg-containing materials to modify the Ti implant surface. This systematic review summarizes the methods, effects, and clinical applications of surface modification of Ti implants with Mg-containing coatings. Database collection was completed on Janury 1, 2023, and a total of 29 relevant studies were ultimately included. Mg can be compounded with different materials and coated to the surface of Ti implants using different methods. In vitro and in vivo experiments have shown that Mg-containing coatings promote cell adhesion and osteogenic differentiation. On the one hand, the surface roughness of implants increases with the addition of Mg-containing coatings, which is thought to have an impact on the osseointegration of the implant. On the other hand, Mg ions promote cell attachment through binding interactions between the integrin family and FAK-related signaling pathways. And Mg ions could induce osseointegration by activating PI3K, Notch, ERK/c-Fos, BMP-4-related signaling pathways and TRPM7 protein channels. Overall, Mg-based coatings show great potential for the surface modification of Ti implants to promote osseointegration. STATEMENT OF SIGNIFICANCE: The inertia surface of titanium (Ti) implants leads to delayed osseointegration. Magnesium (Mg) ions, known for promoting bone regeneration, have been extensively studied to modify the surface of Ti implants. However, no consensus has been reached on the appropriate processing methods, surface roughness and effective concentration of Mg-containing coatings for osseointegration. This systematic review focus on the surface modification of Ti implants with Mg-containing compounds, highlighting the effects of Mg-containing coatings on the surface properties of Ti implants and its associated mechanisms. Besides, we also provide an outlook on future directions to promote the clinical application of Mg-modified implants.

Advanced surface engineering of titanium materials for biomedical applications: From static modification to dynamic responsive regulation

Titanium (Ti) and its alloys have been widely used as orthopedic implants, because of their favorable mechanical properties, corrosion resistance and biocompatibility. Despite their significant success in various clinical applications, the probability of failure, degradation and revision is undesirably high, especially for the patients with low bone density, insufficient quantity of bone or osteoporosis, which renders the studies on surface modification of Ti still active to further improve clinical results. It is discerned that surface physicochemical properties directly influence and even control the dynamic interaction that subsequently determines the success or rejection of orthopedic implants. Therefore, it is crucial to endow bulk materials with specific surface properties of high bioactivity that can be performed by surface modification to realize the osseointegration. This article first reviews surface characteristics of Ti materials and various conventional surface modification techniques involving mechanical, physical and chemical treatments based on the formation mechanism of the modified coatings. Such conventional methods are able to improve bioactivity of Ti implants, but the surfaces with static state cannot respond to the dynamic biological cascades from the living cells and tissues. Hence, beyond traditional static design, dynamic responsive avenues are then emerging. The dynamic stimuli sources for surface functionalization can originate from environmental triggers or physiological triggers. In short, this review surveys recent developments in the surface engineering of Ti materials, with a specific emphasis on advances in static to dynamic functionality, which provides perspectives for improving bioactivity and biocompatibility of Ti implants.

Streamlining the synthesis of amides using Nickel-based nanocatalysts

The synthesis of amides is a key technology for the preparation of fine and bulk chemicals in industry, as well as the manufacture of a plethora of daily life products. Furthermore, it constitutes a central bond-forming methodology for organic synthesis and provides the basis for the preparation of numerous biomolecules. Here, we present a robust methodology for amide synthesis compared to traditional amidation reactions: the reductive amidation of esters with nitro compounds under additives-free conditions. In the presence of a specific heterogeneous nickel-based catalyst a wide range of amides bearing different functional groups can be selectively prepared in a more step-economy way compared to previous syntheses. The potential value of this protocol is highlighted by the synthesis of drugs, as well as late-stage modifications of bioactive compounds. Based on control experiments, material characterizations, and DFT computations, we suggest metallic nickel and low-valent Ti-species to be crucial factors that makes this direct amide synthesis possible.

Nanoscale Morphologies on the Surface of 3D-Printed Titanium Implants for Improved Osseointegration: A Systematic Review of the Literature

Three-dimensional (3D) printing is serving as the most promising approach to fabricate personalized titanium (Ti) implants for the precise treatment of complex bone defects. However, the bio-inert nature of Ti material limits its capability for rapid osseointegration and thus influences the implant lifetime in vivo. Despite the macroscale porosity for promoting osseointegration, 3D-printed Ti implant surface morphologies at the nanoscale have gained considerable attention for their potential to improve specific outcomes. To evaluate the influence of nanoscale surface morphologies on osseointegration outcomes of 3D-printed Ti implants and discuss the available strategies, we systematically searched evidence according to the PRISMA on PubMed, Embase, Web of Science, and Cochrane (until June 2022). The inclusion criteria were in vivo (animal) studies reporting the osseointegration outcomes of nanoscale morphologies on the surface of 3D-printed Ti implants. The risk of bias (RoB) was assessed using the Systematic Review Centre for Laboratory Animal Experimentation (SYRCLE's) tool. The quality of the studies was evaluated using the Animal Research: Reporting of In Vivo Experiments (ARRIVE) guidelines. (PROSPERO: CRD42022334222). Out of 119 retrieved articles, 9 studies met the inclusion criteria. The evidence suggests that irregular nano-texture, nanodots and nanotubes with a diameter of 40-105nm on the surface of porous/solid 3D-printed Ti implants result in better osseointegration and vertical bone ingrowth compared to the untreated/polished ones by significantly promoting cell adhesion, matrix mineralization, and osteogenic differentiation through increasing integrin expression. The RoB was low in 41.1% of items, unclear in 53.3%, and high in 5.6%. The quality of the studies achieved a mean score of 17.67. Our study demonstrates that nanostructures with specific controlled properties on the surface of 3D-printed Ti implants improve their osseointegration. However, given the small number of studies, the variability in experimental designs, and lack of reporting across studies, the results should be interpreted with caution.

Producing Metal Powder from Machining Chips Using Ball Milling Process: A Review

In the pursuit of achieving zero emissions, exploring the concept of recycling metal waste from industries and workshops (i.e., waste-free) is essential. This is because metal recycling not only helps conserve natural resources but also requires less energy as compared to the production of new products from virgin raw materials. The use of metal scrap in rapid tooling (RT) for injection molding is an interesting and viable approach. Recycling methods enable the recovery of valuable metal powders from various sources, such as electronic, industrial, and automobile scrap. Mechanical alloying is a potential opportunity for sustainable powder production as it has the capability to convert various starting materials with different initial sizes into powder particles through the ball milling process. Nevertheless, parameter factors, such as the type of ball milling, ball-to-powder ratio (BPR), rotation speed, grinding period, size and shape of the milling media, and process control agent (PCA), can influence the quality and characteristics of the metal powders produced. Despite potential drawbacks and environmental impacts, this process can still be a valuable method for recycling metals into powders. Further research is required to optimize the process. Furthermore, ball milling has been widely used in various industries, including recycling and metal mold production, to improve product properties in an environmentally friendly way. This review found that ball milling is the best tool for reducing the particle size of recycled metal chips and creating new metal powders to enhance mechanical properties and novelty for mold additive manufacturing (MAM) applications. Therefore, it is necessary to conduct further research on various parameters associated with ball milling to optimize the process of converting recycled copper chips into powder. This research will assist in attaining the highest level of efficiency and effectiveness in particle size reduction and powder quality. Lastly, this review also presents potential avenues for future research by exploring the application of RT in the ball milling technique.

Heat Accumulation-Induced Surface Structures at High Degrees of Laser Pulse Overlap on Ti6Al4V Surfaces by Femtosecond Laser Texturing

In this work, femtosecond laser pulses at high repetition rates were used to fabricate unique microstructures on the surface of Ti6Al4V. We investigated the influence of pulse overlap and laser repetition rates on structure formation. Laser texturing with a high degree of overlap resulted in melting of the material, leading to the formation of specific microstructures that can be used as cavities for drug delivery. The reason for melt formation is attributed to local heat accumulation at high repetition rates. Such structures can be fabricated on materials with low thermal conductivity, which prevent heat dissipation into the bulk of the material. The heat accumulation effect has also been demonstrated on steel, which also has low thermal conductivity.

Molten salt synthesis of CrMnFeNi alloy nanopowder passivated by TiOx–ZrOy shell used as a superior catalyst support in liquid-phase hydrogenation†

A molten salt method was used to prepare CrMnFeNi alloy nanopowder passivated by TiO_x–ZrO_y surface shell with a high specific surface area (23 m² g⁻¹) from the oxide precursors. Analyses by scanning electron microscopy/transmission electron microscopy with energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy revealed the formation of an alloyed Cr–Mn–Fe–Ni-rich core surrounded by an oxide surface shell with a Ti/Zr-rich composition, confirming the formation of TiO_x–ZrO_y/CrMnFeNi nanopowder. It was speculated that the CrMnFeNi alloy nanoparticles were preferentially formed from the constituent metals by a faster reduction of any oxides of Cr, Mn, Fe, and Ni and a subsequent alloying with Ti and Zr could hardly occur due to the high thermodynamic stability of CrMnFeNi alloy. A Ni-loaded TiO_x–ZrO_y/CrMnFeNi catalyst exhibited superior catalytic performance to common Ni-loaded TiO₂ and ZrO₂ in the liquid-phase hydrogenation of p-nitrophenol at room temperature. The enhancement could have originated from an excellent electrical property of CrMnFeNi alloy, promoting the formation of active metallic nickel on the surface during the reaction. Leaching amounts of the constituent elements of Ti–Zr–Cr–Mn–Fe–Ni and loaded Ni was very little in the reaction solution after the reaction; the results confirmed that the prepared CrMnFeNi alloy nanopowder was very stable due to the protection of the Ti/Zr-rich oxide shell. Thus, the potential application of the alloyed powder used as catalyst support was demonstrated.

The enhancement of liquid-phase hydrogenation by NaBH₄ over Ni-loaded CrMnFeNi alloy nanoparticles passivated by TiO_x–ZrO_y.

Osseointegration Properties of Titanium Implants Treated by Nonthermal Atmospheric-Pressure Nitrogen Plasma

Pure titanium is used in dental implants owing to its excellent biocompatibility and physical properties. However, the aging of the material during storage is detrimental to the long-term stability of the implant after implantation. Therefore, in this study, we attempted to improve the surface properties and circumvent the negative effects of material aging on titanium implants by using a portable handheld nonthermal plasma device capable of piezoelectric direct discharge to treat pure titanium discs with nitrogen gas. We evaluated the osteogenic properties of the treated samples by surface morphology and elemental analyses, as well as in vitro and in vivo experiments. The results showed that nonthermal atmospheric-pressure nitrogen plasma can improve the hydrophilicity of pure titanium without damaging its surface morphology while introducing nitrogen-containing functional groups, thereby promoting cell attachment, proliferation, and osseointegration to some extent. Therefore, nitrogen plasma treatment may be a promising method for the rapid surface treatment of titanium implants.

High Performance of Titanium Dioxide Reinforced Acrylonitrile Butadiene Rubber Composites

Recently, dielectric elastomer actuators (DEA) have emerged as one of the most promising materials for use in soft robots. However, DEA needs a high operating voltage and high mechanical properties. By increasing the dielectric constant of elastomeric materials, it is possible to decrease the operating voltage required. Thus, elastomeric composites with a high dielectric constant and strong mechanical properties are of interest. The aim of this research was to investigate the effect of titanium dioxide (TiO₂) content ranging from 0 to 110 phr on the cure characteristics, and physical, dielectric, dynamic mechanical, and morphological properties of acrylonitrile butadiene rubber (NBR) composites. The addition of TiO₂ reduced the scorch time (t_s1) as well as the optimum cure time (t_c90) but increased the cure rate index (CRI), minimum torque (M_L), maximum torque (M_H), and delta torque (M_H - M_L). The optimal TiO₂ content for maximum tensile strength and elongation at break was 90 phr. Tensile strength and elongation at break were increased by 144.8% and 40.1%, respectively, over pure NBR. A significant mechanical property improvement was observed for TiO₂-filled composites due to the good dispersion of TiO₂ in the NBR matrix, which was confirmed by scanning electron microscopy (SEM). Moreover, incorporating TiO₂ filler gave a higher storage modulus, a shift in glass transition temperature (T_g) to a higher temperature, and reduced damping in dynamic mechanical thermal analysis (DMTA). The addition of TiO₂ to NBR rubber increased the dielectric constant of the resultant composites in the tested frequency range from 10² to 10⁵ Hz. As a result, TiO₂-filled NBR composite has a high potential for dielectric elastomer actuator applications.

An update of interbody cages for spine fusion surgeries: from shape design to materials

INTRODUCTION

Discectomy and interbody fusion are widely used in the treatment of intervertebral disc-related diseases. Among them, the interbody cage plays a significant role. However, the complications related to the interbody cage, such as nonunion or pseudoarthrosis, subsidence, loosening, and prolapse of the cage, cannot be ignored. By changing the design and material of the interbody fusion cage, a better fusion effect can be obtained, the incidence of appeal complications can be reduced, and the quality of life of patients after interbody fusion can be improved.

AREAS COVERED

This study reviewed the research progress of cage design and material and discussed the methods of cage design and material to promote intervertebral fusion.

EXPERT OPINION

Current treatment of cervical and lumbar degenerative disease requires interbody fusion to maintain decompression and to promote fusion and reduce the incidence of fusion failure through improvements in implant material, design, internal structure, and function. However, interbody fusion is not an optimal solution for treating vertebral instability.Abbreviations: ACDF, Anterior cervical discectomy and fusion; ALIF, anterior lumbar interbody fusion; Axi-aLIF, axial lumbar interbody fusion; BAK fusion cage, Bagby and Kuslich fusion cage; CADR, cervical artificial disc replacement; DBM, decalcified bone matrix; HA, hydroxyapatite; LLIF/XLIF, lateral or extreme lateral interbody fusion; MIS-TLIF, minimally invasive transforaminal lumbar interbody fusion; OLIF/ATP, oblique lumbar interbody fusion/anterior to psoas; PEEK, Poly-ether-ether-ketone; PLIF, posterior lumbar interbody fusion; ROI-C, Zero-profile Anchored Spacer; ROM, range of motion; SLM, selective melting forming; TLIF, transforaminal lumbar interbody fusion or.

Molten Salt Synthesis of Intermetallic Compound TiNi Nanopowder Passivated by TiOx Shell Prepared from NiTiO3 for Catalytic Hydrogenation

Titanium-nickel alloy is an attractive material due to its unique properties of shape memory effect, superior elasticity, and biocompatibility. Generally, Ti-Ni alloy powders are prepared from pure elemental powders of Ti and Ni as starting materials, but it is an energy-intensive process to obtain pure titanium. In this study, intermetallic compound TiNi powder passivated by TiO_x shell was prepared by directly reducing a commercial NiTiO₃ using CaH₂ reducing agent in a molten LiCl at 650 °C. Analyses by X-ray diffraction, scanning electron microscopy/transmission electron microscopy with energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy revealed that the powder had a core-shell structure, with the core of TiNi and the shell of TiO_x-rich composition with scarce metallic Ni nicely catalyzing hydrogenation reactions with good recyclability and stability.

Device Processing Challenges for Miniaturized Sensing Systems Targeting Biological Fluids

This article presents a review of device processing technologies used in the fabrication of biomedical systems, and highlights the requirements of advanced manufacturing technology. We focus on biomedical systems that perform diagnostics of fluidic specimens, with analytes that are in the liquid phase. In the introduction, we define biomedical systems as well as their versatile applications and the essential current trends. The paper gives an overview of the most important biomolecules that typically must be detected or analyzed in several applications. The paper is structured as follows. First, the conventional architecture and construction of a biosensing system is introduced. We provide an overview of the most common biosensing methods that are currently used for the detection of biomolecules and its analysis. We present an overview of reported biochips, and explain the technology of biofunctionalization and detection principles, including their corresponding advantages and disadvantages. Next, we introduce microfluidics as a method for delivery of the specimen to the biochip sensing area. A special focus lies on material requirements and on manufacturing technology for fabricating microfluidic systems, both for niche and mass-scale production segments. We formulate requirements and constraints for integrating the biochips and microfluidic systems. The possible impacts of the conventional microassembly techniques and processing methods on the entire biomedical system and its specific parts are also described. On that basis, we explain the need for alternative microassembly technologies to enable the integration of biochips and microfluidic systems into fully functional systems.

Diagnostic tests for titanium hypersensitivity in implant dentistry: a systematic review of the literature

PURPOSE

There are rising concerns about titanium hypersensitivity reaction regarding dental endosseous implants. This review aims to summarize and compare the validity and reliability of the available dermatological and laboratory diagnostic tests regarding titanium hypersensitivity. The following PICO design was used: In Patients with titanium dental implants (P) does epicutaneous testing (ECT) (I), compared to lymphocyte transformation test (LTT) or Memory Lymphocyte Immunostimulation Assay (MELISA) (C) detect hypersensitivity reactions (O)? A literature search was performed including all studies dealing with this topic. Studies regarding orthopedic implants were excluded.

METHODS

Three databases (MEDLINE PubMed, Cochrane Library, SciELO) were screened for suitable studies and an additional manual search was also performed. Literature regarding hypersensitivity reactions in orthopedic implants, hypersensitivity reactions regarding implants not related to dental or maxillofacial surgery, animal studies and in vitro studies were excluded. A quality assessment of all selected full-text articles was performed. Randomized, controlled trials were evaluated with the Cochrane Risk of Bias Tool I. Cohort studies were assessed according to the New Castle-Ottawa Scale and case series according to Moga et al. (Development of a quality appraisal tool for case series studies using a modified Delphi technique. 2012).

RESULTS

10 studies were included in the quantitative synthesis and available for the endpoint diagnostics of intolerance reactions to titanium dental implants: 2 clinical studies, 7 cohort studies and 1 case series. The potential for bias (internal validity) for these studies was overall rated as high.

CONCLUSIONS

The study of the available literature regarding ECT and MELISA or LTT in patients with suspected titanium hypersensitivity showed inconsistent results in terms of reliability and validity and thus, those tests should be regarded cautiously. There is strong evidence that titanium hypersensitivity in dental implants is associated with innate immunity: unspecific pro-inflammatory responses due to particle induced hyperreactivity of macrophages or toxicological responses especially towards nanoparticles rather than activation of the adaptive immune system. Therefore, tests detecting allergies do not seem expedient and inflammatory clinical signs should be regarded as leading parameters.

Titanium Dental Implants: An Overview of Applied Nanobiotechnology to Improve Biocompatibility and Prevent Infections

This review addresses the different aspects of the use of titanium and its alloys in the production of dental implants, the most common causes of implant failures and the development of improved surfaces capable of stimulating osseointegration and guaranteeing the long-term success of dental implants. Titanium is the main material for the development of dental implants; despite this, different surface modifications are studied aiming to improve the osseointegration process. Nanoscale modifications and the bioactivation of surfaces with biological molecules can promote faster healing when compared to smooth surfaces. Recent studies have also pointed out that gradual changes in the implant, based on the microenvironment of insertion, are factors that may improve the integration of the implant with soft and bone tissues, preventing infections and osseointegration failures. In this context, the understanding that nanobiotechnological surface modifications in titanium dental implants improve the osseointegration process arouses interest in the development of new strategies, which is a highly relevant factor in the production of improved dental materials.

Revisiting the hydroxylation phenomenon of SiO2: a study through "hard-hard" and "soft-soft" interactions

Surface hydroxylation has been extensively studied over the years for a variety of applications, and studies involving hydroxylation of different silica surfaces are still carried out due to the interesting properties obtained from those modified surfaces. Although a number of theoretical studies have been employed to evaluate details on the hydroxylation phenomenon on silica (SiO₂) surfaces, most of these studies are based on computationally expensive models commonly based on extended systems. In order to circumvent such an aspect, here we present a low-cost theoretical study on the SiO₂ hydroxylation process aiming to evaluate aspects associated with water-SiO₂ interaction. Details about local reactivity, chemical softness, and electrostatic potential were evaluated for SiO₂ model substrates in the framework of the density functional theory (DFT) using a molecular approach. The obtained results from this new and promising approach were validated and complemented by fully atomistic reactive molecular dynamics (FARMD) simulations. Furthermore, the implemented approach proves to be a powerful tool that is not restricted to the study of hydroxylation, opening a promising route for low computational cost to analyze passivation and anchoring processes on a variety of oxide surfaces.

Study of Electrochemical and Biological Characteristics of As-Cast Ti-Nb-Zr-Ta System Based on Its Microstructure

The quaternary Ti-Nb-Zr-Ta (TNZT) alloy was successfully cast-fabricated with the objective to be used in the medical field. Samples’ microstructure was compared to CP-Ti and Ti-6Al-4V (control samples) and related to corrosion, ion release and biological properties. As-cast TNZT was formed with large β grain sizes (285 µm) compared to the ultrafine α grain sizes of CP-Ti (11 µm) and the α + β ultrafine grain sizes of 1.45 µm and 0.74 µm. Hardness and flexural elastic moduli (94 HV and 43 GPa) came close to the biological structures, such as dentin and enamel values. The ion release mechanism of as-cast TNZT was significantly lesser than CP-Ti and Ti-6Al-4V, which can be related to the difference in samples’ grain sizes and chemical compositions. However, the corrosion rate was higher than for the control samples; this way offers corrosion properties inferior with respect to the properties obtained in the reference materials. Biological assays demonstrated that the two-cell (hDPSCs and MG-63) lineage studied presented good adhesion and capability to differentiate in bone cells on the as-cast TNZT surface, and no cytotoxicity effects were found. Details and reasons based on samples’ microstructure are discussed.

Implant-bone-interface: Reviewing the impact of titanium surface modifications on osteogenic processes in vitro and in vivo

Titanium is commonly and successfully used in dental and orthopedic implants. However, patients still have to face the risk of implant failure due to various reasons, such as implant loosening or infection. The risk of implant loosening can be countered by optimizing the osteointegration capacity of implant materials. Implant surface modifications for structuring, roughening and biological activation in favor for osteogenic differentiation have been vastly studied. A key factor for a successful stable long-term integration is the initial cellular response to the implant material. Hence, cell-material interactions, which are dependent on the surface parameters, need to be considered in the implant design. Therefore, this review starts with an introduction to the basics of cell-material interactions as well as common surface modification techniques. Afterwards, recent research on the impact of osteogenic processes in vitro and vivo provoked by various surface modifications is reviewed and discussed, in order to give an update on currently applied and developing implant modification techniques for enhancing osteointegration.

Bioactive Coatings on Titanium: A Review on Hydroxylation, Self-Assembled Monolayers (SAMs) and Surface Modification Strategies

Titanium (Ti) and its alloys have been demonstrated over the last decades to play an important role as inert materials in the field of orthopedic and dental implants. Nevertheless, with the widespread use of Ti, implant-associated rejection issues have arisen. To overcome these problems, antibacterial properties, fast and adequate osseointegration and long-term stability are essential features. Indeed, surface modification is currently presented as a versatile strategy for developing Ti coatings with all these challenging requirements and achieve a successful performance of the implant. Numerous approaches have been investigated to obtain stable and well-organized Ti coatings that promote the tailoring of surface chemical functionalization regardless of the geometry and shape of the implant. However, among all the approaches available in the literature to functionalize the Ti surface, a promising strategy is the combination of surface pre-activation treatments typically followed by the development of intermediate anchoring layers (self-assembled monolayers, SAMs) that serve as the supporting linkage of a final active layer. Therefore, this paper aims to review the latest approaches in the biomedical area to obtain bioactive coatings onto Ti surfaces with a special focus on (i) the most employed methods for Ti surface hydroxylation, (ii) SAMs-mediated active coatings development, and (iii) the latest advances in active agent immobilization and polymeric coatings for controlled release on Ti surfaces.

Mussel-Inspired Carboxymethyl Chitosan Hydrogel Coating of Titanium Alloy with Antibacterial and Bioactive Properties

Infection-related titanium implant failure rates remain exceedingly high in the clinic. Functional surface coating represents a very promising strategy to improve the antibacterial and bioactive properties of titanium alloy implants. Here, we describe a novel bioactive surface coating that consists of a mussel-inspired carboxymethyl chitosan hydrogel loaded with silver nanoparticles (AgNPs) to enhance the bioactive properties of the titanium alloy. The preparation of hydrogel is based on gallic acid grafted carboxymethyl chitosan (CMCS-GA) catalyzed by DMTMM (4-(4,6-dimethoxy-1,3,5-triazin-2-yl)-4-methylmorpholinium chloride). To build a firm bonding between the hydrogel and titanium alloy plate, a polydopamine layer was introduced onto the surface of the titanium alloy. With HRP/H₂O₂ catalysis, CMCS-GA can simply form a firm gel layer on the titanium alloy plate through the catechol groups. The surface properties of titanium alloy were characterized by scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and water contact angle. Silver nanoparticles were loaded into the gel layer by in situ reduction to enhance the antibacterial properties. In vitro antibacterial and cell viability experiments showed that the AgNPs-loaded Ti-gel possesses excellent antibacterial properties and did not affect the proliferation of rabbit mesenchymal stem cells (MSCs).

Chemical route to prepare nickel supported on intermetallic Ti6Si7Ni16 nanoparticles catalyzing CO methanation

In this study, ternary intermetallic nickel silicide, Ti₆Si₇Ni₁₆, nanoparticles with a high surface area of 37.5 m² g^-1 were chemically prepared from SiO₂-impregnated oxide precursors, which were reduced at as low as 600 °C by a CaH₂ reducing agent in molten LiCl, resulting in the formation of single-phase Ti₆Si₇Ni₁₆ with a nanosized morphology. The intermetallic Ti₆Si₇Ni₁₆ phase in the nanoparticles was stabilized in air by surface passive oxide layers of TiO_x-SiO_y, which facilitated the handling of the nanoparticles. Considering our previous successful work of preparing single-phase LaNi₂Si₂ (39.3 m² g^-1) and YNi₂Si₂ (27.0 m² g^-1) nanoparticles in a similar manner, the proposed chemical method showed to be a versatile approach in preparing ternary silicide nanoparticles. In this study, we applied the obtained Ti₆Si₇Ni₁₆ nanoparticles as catalyst supports in CO methanation. The supported nickel catalyst showed an activation energy of 56 kJ mol^-1, which is half as low as that of common TiO₂-supported nickel catalysts. Also, Ni/Ti₆Si₇Ni₁₆ provided the lower activation energy more than any previous Ni-based catalyst. Since the measured work function of Ti₆Si₇Ni₁₆ (4.5 eV) was lower than that of nickel (5.15 eV), it was suggested that the Ti₆Si₇Ni₁₆ support can accelerate the rate-determining step of C-O bond dissociation in CO methanation due to its good electron donation capacity.

In Vitro Corrosion of SiC-Coated Anodized Ti Nano-Tubular Surfaces

Peri-implantitis leads to implant failure and decreases long-term survival and success rates of implant-supported prostheses. The pathogenesis of this disease is complex but implant corrosion is believed to be one of the many factors which contributes to progression of this disease. A nanostructured titanium dioxide layer was introduced using anodization to improve the functionality of dental implants. In the present study, we evaluated the corrosion performance of silicon carbide (SiC) on anodized titanium dioxide nanotubes (ATO) using plasma-enhanced chemical vapor deposition (PECVD). This was investigated through a potentiodynamic polarization test and bacterial incubation for 30 days. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to analyze surface morphologies of non-coated and SiC-coated nanotubes. Energy dispersive X-ray (EDX) was used to analyze the surface composition. In conclusion, SiC-coated ATO exhibited improved corrosion resistance and holds promise as an implant coating material.

Research to Clinics: Clinical Translation Considerations for Anodized Nano-Engineered Titanium Implants

Titania nanotubes (TNTs) fabricated on titanium orthopedic and dental implants have shown significant potential in "proof of concept" in vitro, ex vivo, and short-term in vivo studies. However, most studies do not focus on a clear direction for future research towards clinical translation, and there exists a knowledge gap in identifying key research challenges that must be addressed to progress to the clinical setting. This review focuses on such challenges with respect to anodized titanium implants modified with TNTs, including optimized fabrication on clinically utilized microrough surfaces, clinically relevant bioactivity assessments, and controlled/tailored local release of therapeutics. Further, long-term in vivo investigations in compromised animal models under loading conditions are needed. We also discuss and detail challenges and progress related to the mechanical stability of TNT-based implants, corrosion resistance/electrochemical stability, optimized cleaning/sterilization, packaging/aging, and nanotoxicity concerns. This extensive, clinical translation focused review of TNTs modified Ti implants aims to foster improved understanding of key research gaps and advances, informing future research in this domain.

Osteoblastic response to biomaterials surfaces: Extracellular matrix proteomic analysis

The cellular response to surfaces is mediated, among other factors, by the extracellular matrix (ECM). However, little is known about the ECM proteome during mineralization. Our objective was to compare the ECM composition formed by osteoblast on different materials surfaces with proteomic analysis. Three types of biomaterial surfaces (pure titanium, anodized titanium, and zirconia) were used. Osteoblasts (MC3T3 linage) cells were cultivated on the biomaterials for 7, 14, and 21 days with the osteogenic medium. For the proteomic analysis, the specimens were washed, decellularized, and the ECM was collected. The majority of the typical ECM proteins, out of a total of 24 proteins identified, was expressed and regulated equally on the three biomaterials tested. Alpha-1,4 glucan phosphorylase was found to be down-regulated on zirconia on the seventh day, while at the same time, glycogen phosphorylase brain form was up-regulated on anodized titanium, both when compared with pure titanium (ratio: 1.06 and 0.97, respectively). And after 14 days of culture, glycogen phosphorylase brain form was downregulated on zirconia when compared with pure titanium (ratio: 0.90), suggesting the influence of material surface roughness and chemical composition on energy metabolism. Proteins related to bone development like Transforming growth factor beta-3 and Fibroblast growth factor 8 were found exclusively on pure titanium on the 21st day. Altogether, our results show a possible influence of material surfaces on the composition of ECM.

Cu-Co Co-Doped Microporous Coating on Titanium with Osteogenic and Antibacterial Properties

Titanium (Ti) and its alloys are widely used in bone surgery by virtue of their excellent mechanical properties and good biocompatibility; however, complications such as loosening and sinking have been reported post-implantation. Herein we deposited a copper-cobalt (Cu-Co) co-doped titanium dioxide (TUO) coating on the surface of Ti implants by microarc oxidation. The osteogenic and antimicrobial properties of the coating were evaluated by in vitro experiments, and we also assessed β-catenin expression levels on different sample surfaces. Our results revealed that the coating promoted the adhesion, proliferation, and differentiation of MG63 osteoblasts, and TUO coating promoted β-catenin expression; moreover, the proliferation of Staphylococcus aureus was inhibited. To summarize, we report that Cu-Co co-doping can enhance the osteogenic and antibacterial activities of orthopedic Ti implants, leading to potentially improved clinical performance.

Ag- and Sr-enriched nanofibrous titanium phosphate phases as potential antimicrobial cement and coating for a biomedical alloy

Biomaterials and their surfaces regulate the biological response and ultimately the quality of healing at a possible site of implantation. The physical, chemical and topographical properties of implants' surfaces play a decisive role in the biological integration process for their immediate loading and long-term success. Since at this level of biological interaction nano-dimensionality is basically entailed, bio-functional nanostructured composites either as filling/cement or coating to metallic implants are required. This study shows the possibility of synthesizing two phases of nanostructured titanium phosphate (π and ρ polymorphs) and enriching them with silver nanoparticles and strontium. More importantly, Ag-Sr-enriched nanostructured π‑titanium phosphate is induced to grow on a commercially available titanium alloy (Ti-6Al-4V), widely used in orthopedic and dental implants, under highly controlled conditions. Structural and microscopic studies, using XRD, HRTEM and SEM altogether confirm the resultant phases and their enrichment with strontium and silver nanoparticles with an average particle size around 6 nm. Using confocal laser scanning microscopy, the surface roughness was measured and is found to lay at the interface between the nanosized and microsized topologies. Ion release assessments showed that the presence of strontium controlled the release rate of silver ions and this could be beneficial in terms of decreasing the accompanied cytotoxicity that is usually encountered at high concentrations of silver release. Antimicrobial and cell proliferation assays have proved that enriching titanium phosphate with strontium and silver nanoparticles has improved their antimicrobial properties, while the cytotoxicity could be controlled.

Porous intermetallic Ni2XAl (X = Ti or Zr) nanoparticles prepared from oxide precursors

Porous intermetallic Ni₂XAl (X = Ti or Zr) nanoparticles with small crystallite sizes (24-34 nm) and high Brunauer-Emmett-Teller (BET) surface areas (10-71 m² g^-1) were prepared from oxide precursors by a chemical route. CaH₂ acted as a template to form the porous morphologies and assisted the reduction.

γ-ray induced formation of oxygen vacancies and Ti3+ defects in anatase TiO2 for efficient photocatalytic organic pollutant degradation

Oxygen vacancies and Ti³⁺ defects in anatase TiO₂ have attracted great attention to address the insufficient optical absorption and photoinduced charge-carrier separation in photocatalysis. In this study, we demonstrate a superficial and innovative approach for synthesizing anatase TiO₂ nanoparticles with abundant oxygen vacancies via γ-ray irradiation reduction at room temperature. X-ray photoelectron spectroscopy (XPS) and electron paramagnetic resonance (EPR) confirm that oxygen vacancies and Ti³⁺ defects can be quantitatively and extensively obtained by merely regulating the irradiation dosage. Photoelectrochemical measurements suggest that oxygen vacancies and Ti³⁺ defects promoted the separation of electron-hole pairs and then enhanced the photocatalytic degradation performance for organic pollutant. In comparison with TiO₂ (no irradiation), the sample (49.5 kGy irradiation) exhibited a 20.0-fold enhancement in visible-light decomposition of phenol. In addition, the results of scavenge experiments and mechanism analysis revealed that O₂^- are the dominant active species. The excited electrons generated at the conduction band and oxygen vacancy level of TiO_2-x-49.5 conspicuously contributes to generate much more ·O₂^- species. This novel study shows at room temperature, the γ-ray approach of irradiation leads to faster formation and quantification of oxygen vacancies in the semiconductor materials.

Green Synthesized Palladium Coated Titanium Nanotube Arrays for Simultaneous Azo-Dye Degradation and Hydrogen Production

In this study, electrodes of titanium dioxide nanotube arrays (TNAs) were successfully synthesized by applying the anodic oxidation etching method, as well as the use of green synthetic technology to add reducing agents of tea or coffee to reduce metal palladium from palladium chloride. Synthesis of palladium modified TNAs (Pd/TNAs) was conducted by the microwave hydrothermal method after the metal palladium was reduced. In order to identify the surface structure, light absorption and elemental composition, TNAs and Pd/TNAs were characterized by X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). Furthermore, to test the photocurrent density, electron resistance, and hydroxyl radicals by I-t plot, electrochemistry impedance spectroscopy (EIS), and electron paramagnetic resonance (EPR) were investigated. The photocurrent (4.0 mA/cm2) of Pd/TNAs-C (using coffee as the reducing agent) at +1.0 V (vs. Ag/AgCl) was higher than that of the pure TNAs (1.5 mA/cm2), illustrating that Pd/TNAs-C can effectively separate photogenerated electrons and holes. Pd/TNAs is a favorable material as a photoanode for the photoelectrochemical (PEC) removal of organic pollutants in wastewater.

A Comprehensive Review on the Corrosion Pathways of Titanium Dental Implants and Their Biological Adverse Effects

The main aim of this work was to perform a comprehensive review of findings reported by previous studies on the corrosion of titanium dental implants and consequent clinical detrimental effects to the patients. Most studies were performed by in vitro electrochemical tests and complemented with microscopic techniques to evaluate the corrosion behavior of the protective passive oxide film layer, namely TiO2. Results revealed that bacterial accumulation, dietary, inflammation, infection, and therapeutic solutions decrease the pH of the oral environment leading to the corrosion of titanium. Some therapeutic products used as mouthwash negatively affect the corrosion behavior of the titanium oxide film and promote changes on the implant surface. In addition, toothpaste and bleaching agents, can amplify the chemical reactivity of titanium since fluor ions interacting with the titanium oxide film. Furthermore, the number of in vivo studies is limited although corrosion signs have been found in retrieved implants. Histological evaluation revealed titanium macro- and micro-scale particles on the peri-implant tissues. As a consequence, progressive damage of the dental implants and the evolution of inflammatory reactions depend on the size, chemical composition, and concentration of submicron- and nanoparticles in the surrounding tissues and internalized by the cells. In fact, the damage of the implant surfaces results in the loss of material that compromises the implant surfaces, implant-abutment connections, and the interaction with soft tissues. The corrosion can be an initial trigger point for the development of biological or mechanical failures in dental implants.

Demonstration of a SiC Protective Coating for Titanium Implants

To mitigate the corrosion of titanium implants and improve implant longevity, we investigated the capability to coat titanium implants with SiC and determined if the coating could remain intact after simulated implant placement. Titanium disks and titanium implants were coated with SiC using plasma-enhanced chemical vapor deposition (PECVD) and were examined for interface quality, chemical composition, and coating robustness. SiC-coated titanium implants were torqued into a Poly(methyl methacrylate) (PMMA) block to simulate clinical implant placement followed by energy dispersive spectroscopy to determine if the coating remained intact. After torquing, the atomic concentration of the detectable elements (silicon, carbon, oxygen, titanium, and aluminum) remained relatively unchanged, with the variation staying within the detection limits of the Energy Dispersive Spectroscopy (EDS) tool. In conclusion, plasma-enhanced chemical vapor deposited SiC was shown to conformably coat titanium implant surfaces and remain intact after torquing the coated implants into a material with a similar hardness to human bone mass.

Enhanced Osseointegration and Bio-Decontamination of Nanostructured Titanium Based on Non-Thermal Atmospheric Pressure Plasma

Alkali-treated titanate layer with nanonetwork structures (TNS) is a promising surface for improving osseointegration capacity in implants. Nevertheless, there is a risk of device failure as a result of insufficient resistance to biofilm contamination. This study tested whether treatment using a handheld non-thermal plasma device could efficiently eliminate biofilm contamination without destroying the surface nanostructure while re-establishing a surface that promoted new bone generation. TNS specimens were treated by a piezoelectric direct discharge (PDD) plasma generator. The effect of decontamination was performed utilizing Staphylococcus aureus. The evaluation of initial cell attachment with adhesion images, alkaline phosphatase activity, extracellular matrix mineralization, and expression of genes related to osteogenesis was performed using rat bone marrow mesenchymal stem cells, and the bone response were evaluated in vivo using a rat femur model. Nanotopography and surface roughness did not significantly differ before and after plasma treatments. Cell and bone formation activity were improved by TNS plasma treatment. Furthermore, plasma treatment effectively eliminated biofilm contamination from the surface. These results suggested that this plasma treatment may be a promising approach for the treatment of nanomaterials immediately before implantation and a therapeutic strategy for peri-implantitis.

Synthesis of Chitosan Beads Incorporating Graphene Oxide/Titanium Dioxide Nanoparticles for In Vivo Studies

Scaffold development for cell regeneration has increased in recent years due to the high demand for more efficient and biocompatible materials. Nanomaterials have become a critical alternative for mechanical, thermal, and antimicrobial property reinforcement in several biopolymers. In this work, four different chitosan (CS) bead formulations crosslinked with glutaraldehyde (GLA), including titanium dioxide nanoparticles (TiO₂), and graphene oxide (GO) nanosheets, were prepared with potential biomedical applications in mind. The characterization of by FTIR spectroscopy, X-ray photoelectron spectroscopy (XRD), thermogravimetric analysis (TGA), energy-dispersive spectroscopy (EDS) and scanning electron microscopy (SEM), demonstrated an efficient preparation of nanocomposites, with nanoparticles well-dispersed in the polymer matrix. In vivo, subdermal implantation of the beads in Wistar rat′s tissue for 90 days showed a proper and complete healing process without any allergenic response to any of the formulations. Masson′s trichrome staining of the histological implanted tissues demonstrated the presence of a group of macrophage/histiocyte compatible cells, which indicates a high degree of biocompatibility of the beads. The materials were very stable under body conditions as the morphometry studies showed, but with low resorption percentages. These high stability beads could be used as biocompatible, resistant materials for long-term applications. The results presented in this study show the enormous potential of these chitosan nanocomposites in cell regeneration and biomedical applications.

A novel BSA immobilizing manner on modified titanium surface ameliorates osteoblast performance

Surface modification of medical and dental devices, to improve their biocorrosion resistance and biocompatibility, can be achieved with the multidisciplinary field of biomaterials. Nanostructured titanium dioxide (TiO₂) has been employed as surface modifier of titanium-based biomaterials because it can prevent the failure of the devices due to wear mechanisms. Moreover, this oxide surface is mostly terminated by hydroxyl groups (-OH) that can be directly functionalized with biomolecules to improve the biocompatibility of these devices. We explored the influence of 3-aminopropyltrimethoxysilane (APTMS) molecules as spacers in bovine serum albumin (BSA) protein immobilization on the physically hydroxylated surfaces of rutile phase TiO₂ films grown by reactive Radio Frequency (RF) magnetron sputtering. X-ray Photoelectron Spectroscopy (XPS) was used to examine the adsorption of BSA and APTMS on the hydroxylated surface of TiO₂ thin films. For biological tests, BSA was directly immobilized on the film surface and on the APTMS monolayer. Biological analysis found better osteoblast performance considering gene markers related to cell adhesion after interacting directly with the surface modified by the immobilization of BSA, especially on the surface where this protein was immobilized by APTMS. Additionally, we addressed the relevance of this biointerfaces on extracellular matrix remodeling by zymography analysis. Altogether, our data provides new insights about the cellular and molecular mechanisms covering the improved osteoblastic response of the proposed surface modification.

Low-Temperature Growing Anatase TiO2/SnO2 Multi-dimensional Heterojunctions at MXene Conductive Network for High-Efficient Perovskite Solar Cells

A multi-dimensional conductive heterojunction structure, composited by TiO2, SnO2, and Ti3C2TX MXene, is facilely designed and applied as electron transport layer in efficient and stable planar perovskite solar cells. Based on an oxygen vacancy scramble effect, the zero-dimensional anatase TiO2 quantum dots, surrounding on two-dimensional conductive Ti3C2TX sheets, are in situ rooted on three-dimensional SnO2 nanoparticles, constructing nanoscale TiO2/SnO2 heterojunctions. The fabrication is implemented in a controlled low-temperature anneal method in air and then in N2 atmospheres. With the optimal MXene content, the optical property, the crystallinity of perovskite layer, and internal interfaces are all facilitated, contributing more amount of carrier with effective and rapid transferring in device. The champion power conversion efficiency of resultant perovskite solar cells achieves 19.14%, yet that of counterpart is just 16.83%. In addition, it can also maintain almost 85% of its initial performance for more than 45 days in 30-40% humidity air; comparatively, the counterpart declines to just below 75% of its initial performance.

Roles of TiO2 in the highly robust Au nanoparticles-TiO2 modified polyaniline electrode towards non-enzymatic sensing of glucose

Along with the rise of diabetes mellitus issue, glucose sensor has become an imperative tool for healthcare. Studies have been widely conducted on electrode materials for glucose sensors; metal nanoparticles and/or oxide particles in its nano-size are reported to exhibit remarkable electrocatalytic activities in the non-enzymatic glucose sensors. However, the decoration processes of metal nanoparticles or nano-sized oxides are known to be tedious and time-consuming. In addition, the processes usually result in great amount of waste solution emission. In this study, therefore, an Au nanoparticles (NPs)-TiO₂ modified polyaniline (PANI) composite is practiced towards the applications of non-enzymatic glucose sensors, by using a facile and time-saving thermal reduction and by electrodeposition techniques with low waste solution emission. Au NPs, which is modified with TiO₂ nanoparticles in its optimized amount, performs the highest electrocatalytic activity to the oxidation of glucose in alkaline solution. The stability of Au NPs-TiO₂/PANI is superior to those of most reported results over 70 days. The sensitivity and detection limit are 379.8 μA mM^-1 cm^-2 and 0.15 μM, respectively. High selectivity of Au NPs-TiO₂/PANI is also confirmed by the interference test. Spill-over effect of OH^- between Au NPs and TiO₂, which is the main reason for the improved catalytic activity, is described in this study.

A titanium dioxide/nitrogen-doped graphene quantum dot nanocomposite to mitigate cytotoxicity: synthesis, characterisation, and cell viability evaluation

Titanium dioxide nanoparticles (TiO₂ NPs) have attracted tremendous interest owing to their unique physicochemical properties. However, the cytotoxic effect of TiO₂ NPs remains an obstacle for their wide-scale applications, particularly in drug delivery systems and cancer therapies. In this study, the more biocompatible nitrogen-doped graphene quantum dots (N-GQDs) were successfully incorporated onto the surface of the TiO₂ NPs resulting in a N-GQDs/TiO₂ nanocomposites (NCs). The effects of the nanocomposite on the viability of the breast cancer cell line (MDA-MB-231) was evaluated. The N-GQDs and N-GQDs/TiO₂ NCs were synthesised using a one- and two-pot hydrothermal method, respectively while the TiO₂ NPs were fabricated using microwave-assisted synthesis in the aqueous phase. The synthesised compounds were characterised using Fourier transform infrared (FTIR) spectroscopy, high-resolution transmission electron microscopy (HRTEM), field emission scanning electron microscopy (FESEM) and UV-visible spectrophotometry. The cell viability of the MDA-MB-231 cell line was determined using a CellTiter 96® AQueous One Solution Cell Proliferation (MTS) assay. The obtained results indicated that a monodispersed solution of N-GQDs with particle size 4.40 ± 1.5 nm emitted intense blue luminescence in aqueous media. The HRTEM images clearly showed that the TiO₂ particles (11.46 ± 2.8 nm) are square shaped. Meanwhile, TiO₂ particles were located on the 2D graphene nanosheet surface in N-GQDs/TiO₂ NCs (9.16 ± 2.4 nm). N-GQDs and N-GQDs/TiO₂ NCs were not toxic to the breast cancer cells at 0.1 mg mL⁻¹ and below. At higher concentrations (0.5 and 1 mg mL⁻¹), the nanocomposite was significantly less cytotoxic compared to the pristine TiO₂. In conclusion, this nanocomposite with reduced cytotoxicity warrants further exploration as a new TiO₂-based nanomaterial for biomedical applications, especially as an anti-cancer strategy.

Cytotoxicity mitigation using titanium dioxide/nitrogen-doped graphene quantum dot nanocomposites.

Chemical and Biological Roles of Zinc in a Porous Titanium Dioxide Layer Formed by Micro-Arc Oxidation

This study investigated the time transient effect of zinc (Zn) in the porous titanium dioxide formed by micro-arc oxidation (MAO) treatment routinely performed for Zn-containing electrolytes. The aim of our analysis was to understand the changes in both the chemical and biological properties of Zn in physiological saline. The morphology of the Zn-incorporated MAO surface did not change, and a small amount of Zn ions were released at early stages of incubation in saline. We observed a decrease in Zn concentration in the oxide layer because its release and chemical state (Zn2+ compound to ZnO) changed over time during incubation in saline. In addition, the antibacterial property of the Zn-incorporated MAO surface developed at late periods after the incubation process over a course of 28 days. Furthermore, osteogenic cells were able to proliferate and were calcified on the specimens with Zn. The changes related to Zn in saline had non-toxic effects on the osteogenic cells. In conclusion, the time transient effect of Zn in a porous titanium dioxide layer was beneficial to realize dual functions, namely the antibacterial property and osteogenic cell compatibility. Our study suggests the importance of the chemical state changes of Zn to control its chemical and biological properties.

Nano-Scale Surface Modifications to Advance Current Treatment Options for Cervical Degenerative Disc Disease (CDDD)

Degenerative Disc Disease (DDD) causes a nagging to severe back pain as well as numbing sensation to the extremities leading to loss of overall patients' height and weakness to leg muscles. Degenerative disc disease is often observed in aging patients as well as patients who have suffered from a back injury. Cervical Degenerative Disc Disease (CDDD) is a progressive condition that leads to the degeneration of the intervertebral discs supporting the cervical vertebral column. Anterior Cervical Interbody Fusion (ACIF) has been the longstanding treatment option for severe degenerative disc disease; however, ACIF presents various novel complications, necessitating numerous comparative device studies to reduce the negative effects of spinal fusion. Cervical disc arthroplasty, the recent focus of clinical attention, was one of the alternatives studied to mitigate the complications associated with vertebral fusion but presents its own disadvantages. These complications prompted further investigation and modifications that can be introduced into these devices. We will be discussing the nano-scale interactions between the implant and extracellular matrix play a crucial role in device integration and efficacy, providing an additional approach towards a device's overall success.

Nano-scale modification of titanium implant surfaces to enhance osseointegration

The main aim of this review study was to report the state of art on the nano-scale technological advancements of titanium implant surfaces to enhance the osseointegration process. Several methods of surface modification are chronologically described bridging ordinary methods (e.g. grit blasting and etching) and advanced physicochemical approaches such as 3D-laser texturing and biomimetic modification. Functionalization procedures by using proteins, peptides, and bioactive ceramics have provided an enhancement in wettability and bioactivity of implant surfaces. Furthermore, recent findings have revealed a combined beneficial effect of micro- and nano-scale modification and biomimetic functionalization of titanium surfaces. However, some technological developments of implant surfaces are not commercially available yet due to costs and a lack of clinical validation for such recent surfaces. Further in vitro and in vivo studies are required to endorse the use of enhanced biomimetic implant surfaces. STATEMENT OF SIGNIFICANCE: Grit-blasting followed by acid-etching is currently used for titanium implant modifications, although recent technological biomimetic physicochemical methods have revealed enhanced osteoconductive and anti-microbial outcomes. An improvement in wettability and bioactivity of titanium implant surfaces has been accomplished by combining micro and nano-scale modification and functionalization with protein, peptides, and bioactive compounds. Such morphological and chemical modification of the titanium surfaces induce the migration and differentiation of osteogenic cells followed by an enhancement of the mineral matrix formation that accelerate the osseointegration process. Additionally, the incorporation of bioactive molecules into the nanostructured surfaces is a promising strategy to avoid early and late implant failures induced by the biofilm accumulation.

Evaluation of floor-wise pollution status and deposition behavior of potentially toxic elements and nanoparticles in air conditioner dust during urbanistic development

The study was undertaken to investigate deposition behaviors of various size-segregated particles and indoor air quality using dust accumulated on the air conditioner filter acting as a sink for PTEs and nanoparticles that can pose a significant health risk. However, the particulate matter size and chemical composition in AC dust and its relationship with PTEs remains uncertain. Current study aims to investigate the PTEs and nanoparticles composition of AC dust using different analytical approaches including ICP-MS, XRD, XPS, SEM/TEM along with EDS and Laser Diffraction particle size analyzer. The mean concentration of PTEs like Al, As, Cd, Cu, Li, Pb, Sb, Se, Sn, Ti, V and Zn exceeded the corresponding background value. Pb, As, Sn, Sb, Cd were categorizing under geo-accumulation index class IV. Most of the particles were found to be > 100 μm and it decreased significantly with increase in floor altitude. A significantly negative correlation was found between particles size and PTEs concentration showing a significant increase in PTEs content with decrease in particles size. The XPS results showed dominant peaks for TiO₂, Ti-O-N, As₂O₃, Fe⁺³, Fe⁺², Al-OH and Al₂0₃. Additionally, As, Pb, Si and Fe were dominant metallic nanoparticles identified using SEM/TEM along with EDS.

Mesoporous hollow black TiO2 with controlled lattice disorder degrees for highly efficient visible-light-driven photocatalysis

Black TiO₂ has received tremendous attention because of its lattice disorder-induced reduction in the TiO₂ bandgap, which yields excellent light absorption and photocatalytic ability. In this report, a highly efficient visible-light-driven black TiO₂ photocatalyst was synthesized with a mesoporous hollow shell structure. It provided a higher specific surface area, more reaction sites and enhanced visible light absorption capability, which significantly promoted the photocatalytic reaction. Subsequently, the mesoporous hollow black TiO₂ with different lattice disorder-engineering degrees were designed. The structure disorder in the black TiO₂ obviously increased with reduction temperature, leading to improved visible light absorption. However, their visible-light-driven photocatalytic efficiency increased first and then decreased. The highest value can be observed for the sample reduced at 350 °C, which was 2-, 1.4- and 5-fold that of the samples reduced at 320 °C, 380 °C and 400 °C, respectively. This contradiction can be ascribed to the varied functions of the surface defects with different concentrations in the black TiO₂ during the catalytic process. In particular, the defects at low concentrations boost photocatalysis but reverse photocatalysis at high concentrations when they act as charge recombination centers. This study provides significant insight for the fabrication of high-efficiency visible-light-driven catalytic black TiO₂ and the understanding of its catalysis mechanism.

Our work provides significant insights into the design of hollow black TiO₂ spheres and the mechanism accounting for their high-efficient visible-light-driven catalysis.

A TiO2/C catalyst having biomimetic channels and extremely low Pt loading for formaldehyde oxidation

This study presents a TiO₂/C hybrid material with biomimetic channels fabricated using a wood template. Repeated impregnations of pretreated wood chips in a Ti precursor were conducted, followed by calcination at 400–600 °C for 4 hours under a nitrogen atmosphere. The generated TiO₂ nanocrystals were homogenously distributed inside a porous carbon framework. With an extremely low Pt catalyst loading (0.04–0.1 wt%), the obtained porous catalyst could effectively oxidize formaldehyde to CO₂ and H₂O even under room temperature (conv. ∼100%). Wood acted as both a structural template and reduction agent for Pt catalyst generation in sintering. Therefore, no post H₂ reduction treatment for catalyst activation was required. The hierarchal channel structures, including 2–10 nm mesopores and 20 μm diameter channels, could be controlled by calcination temperature and atmosphere, which was confirmed by SEM and BET characterizations. Based on the abundant availability of wood templates and reduced cost for low Pt loading, this preparation method shows great potential for large-scale applications.

This study presents a TiO₂/C hybrid material with biomimetic channels fabricated using a wood template.