Thermal Soil Radon Mitigation

In this work, consideration is given to the possibility for thermal soil radon mitigation. It is known that the diffusion coefficients of radon through minerals and rocks are characterized by Arrhenius linear plots and then increasing as the temperature increases. For the case of rocks, for example, it was observed that a mild heating, less than 100 °C, translates into a radon release, which can be enhanced by 100–1000 times than the normal release at standard temperature and pressure. Therefore, it is reasonable to think that if soil is deliberately heated and then creating a thermal gradient, it could be possible to pump radon from soil because the radon atoms will escape preferentially from cold regions (low diffusion coefficient) toward hot regions (high diffusion coefficients) where a radon sink is located. Utilizing a simplified two-group thermal one-dimensional model, an expression was derived, which allows a first assessment on this possible mitigation technique.

A First Assessment of an Aerodynamic Barrier Layer for Filtering Airborne Hygroscopic Particles

In this work, consideration is given to an aerodynamic concept to boost the filtration in face masks of airborne hygroscopic particles such as those caused by an infected person when coughs or sneezes. Nowadays, increasing the filtration efficiency of face masks implies either increasing the number of crisscrossing fiber layers or decreasing the equivalent hydraulic diameter of the pore, however, both measures are in clear detriment of its breathability. Here, a novel strategy is proposed in which the filtration of an airborne particle is boosted by increasing its diameter. We called properly this concept as the aerodynamic barrier layer. In this concept, a traditional crisscrossing fiber layer is replaced by a parallel rearranged of the fibers in the direction of the flow. This rearrangement will promote central lift forces which will push the particles toward the center of the channel where after clustering they will coalesce resulting in a bigger particle that can be now easily captured by a conventional fiber crisscrossing layer. Utilizing a simplified geometrical model, an expression for the required length of the aerodynamic barrier layer was derived. It is shown that an aerodynamic barrier layer with a length of only a few millimeters can aerodynamically focus water droplets around 1 μm-diameter and the penetration of airborne particles can be reduced up to 55%.

The mechanical effect of moisturization on airborne COVID-19 transmission and its potential use as control technique

Mounting evidence from scientific community seems to suggest that COVID-19 virus can potentially spread by airborne transmission. As a result, methods and techniques for preventing environmental contagious, such as ventilation or air filtration have been proposed. Here, it is investigated the effect of moisturization on airborne COVID-19 transmission from a mechanical point of view in which comparatively large water droplets promote the growth -by collision and coalescence, of suspended airborne COVID-19 and then accelerating its gravitational settling. Utilizing a classical raindrop collisional model from cloud science and the available experimental data an expression for the removal time of suspended airborne COVID-19 as function of the relative humidity was derived. The mechanical model is in good agreement with the recent reported experimental research in which high temperature and high relative humidity reduce COVID-19 contagious and then is a point in favor of the mechanic model of the effect of moisture in the COVID-19 airborne transmission. The results encourage further research on the deliberate moisturization of room air (by using ceiling mounted humidifiers) as a potential technique for control of airborne COVID-19 transmission.

Are Runners More Prone to Become Infected with COVID-19? An Approach from the Raindrop Collisional Model

It is known that COVID-19 spread mainly from person-to-person through respiratory droplets produced when an infected person coughs or sneezes, and as a result certain ideas about contagious of COVID-19 have been spread. One of them is the widespread belief that close runners, owing to the stronger exhalation, can be more prone to be infected with COVID-19 because the collision with the suspended respiratory droplets should the runner in front be infected. However, because of the low Stokes number this idea cannot be generalized without carefully thought and in fact can be put into question. Utilizing the raindrop collisional model and with the help of computational fluid dynamics (CFD), it is shown that the probability of collision with respiratory droplets is not always increasing with the approaching velocity of the runner but rather there is a maximum velocity threshold at which the efficiency of collision drops.

The behavior of radiogenic particles at solidification fronts

The thermal behavior of insoluble radiogenic particles at the solid-liquid interface of an advancing solidification front and its significance with regard to environmental impact are discussed. It is shown that, unlike classical particles, where the most probable behavior is engulfing by the solidification front, radiogenic particles are more likely to be rejected by the solidification front. Utilizing a simplified physical model, an adaptation of classical theoretical models is performed, where it is shown that, unlike classical particles, for radiogenic particles the mechanism is thermally driven. An analytical expression for the critical velocity of the solidification front for engulfing/rejection to occur is derived. The study could be potentially important to several fields, e.g. in engineering applications where technological processes for the physical removal of radionuclide particles dispersed throughout another substance by inducing solidification could be envisaged, in planetary science where the occurrence of radiogenic concentration could result in the possibility of the eruption of primordial comet/planetoids, or, if specific conditions are suitable, particle ejection may result in an increase in concentration as the front moves, which can translate into the formation of hot spots.

Development of a mechanism and an accurate and simple mathematical model for the description of drug release: Application to a relevant example of acetazolamide-controlled release from a bio-inspired elastin-based hydrogel

Transversality between mathematical modeling, pharmacology, and materials science is essential in order to achieve controlled-release systems with advanced properties. In this regard, the area of biomaterials provides a platform for the development of depots that are able to achieve controlled release of a drug, whereas pharmacology strives to find new therapeutic molecules and mathematical models have a connecting function, providing a rational understanding by modeling the parameters that influence the release observed. Herein we present a mechanism which, based on reasonable assumptions, explains the experimental data obtained very well. In addition, we have developed a simple and accurate “lumped” kinetics model to correctly fit the experimentally observed drug-release behavior. This lumped model allows us to have simple analytic solutions for the mass and rate of drug release as a function of time without limitations of time or mass of drug released, which represents an important step-forward in the area of in vitro drug delivery when compared to the current state of the art in mathematical modeling. As an example, we applied the mechanism and model to the release data for acetazolamide from a recombinant polymer. Both materials were selected because of a need to develop a suitable ophthalmic formulation for the treatment of glaucoma. The in vitro release model proposed herein provides a valuable predictive tool for ensuring product performance and batch-to-batch reproducibility, thus paving the way for the development of further pharmaceutical devices.

Efficient cell and cell-sheet harvesting based on smart surfaces coated with a multifunctional and self-organizing elastin-like recombinamer

A wide range of smart surfaces with novel properties relevant for biomedical applications have been developed recently. Herein we focus on thermoresponsive surfaces that switch between cell-adherent and nonadherent states and their applications for cell harvesting. These smart surfaces are obtained by covalently coupling a tailored elastin-like recombinamer onto glass surfaces by means of the well-known and widely applied Click Chemistry methodology. The resulting recombinamer-functionalized surfaces have been characterized by means of water contact angle measurements, XPS and TOF-SIMS. A cell-based analysis of these surfaces with human fibroblasts showed a high degree of adhesion to the surface in its adherent state (37 °C), thus, promoting cell viability and proliferation. A temperature decrease triggers reorganization of the recombinamer, thus, markedly increasing the number of nonadherent domains and masking the adherent ones. This process allows a specific and efficient temporal control of cell adhesion and cell detachment. After determination of the properties required for a suitable cell-harvesting system, optimization of the process allows single cells or cell sheets from at least two types of cells (HFF-1 and ADSCs) to be rapidly harvested.

Layer-by-layer assembly of chitosan and recombinant biopolymers into biomimetic coatings with multiple stimuli-responsive properties

In this work, biomimetic smart thin coatings using chitosan and a recombinant elastin-like recombinamer (ELR) containing the cell attachment sequence arginine-glycine-(aspartic acid) (RGD) are fabricated through a layer-by-layer approach. The synthetic polymer is characterized for its molecular mass and composition using mass spectroscopy and peptide sequencing. The adsorption of each polymeric layer is followed in situ at room temperature and pH 5.5 using a quartz-crystal microbalance with dissipation monitoring, showing that both polymers can be successfully combined to conceive nanostructured, multilayered coatings. The smart properties of the coatings are tested for their wettability by contact angle (CA) measurements as a function of external stimuli, namely temperature, pH, and ionic strength. Wettability transitions are observed from a moderate hydrophobic surface (CAs approximately from 62° to 71°) to an extremely wettable one (CA considered as 0°) as the temperature, pH, and ionic strength are raised above 50 °C, 11, and 1.25 M, respectively. Atomic force microscopy is performed at pH 7.4 and pH 11 to assess the coating topography. In the latter, the results reveal the formation of large and compact structures upon the aggregation of ELRs at the surface, which increase water affinity. Cell adhesion tests are conducted using a SaOs-2 cell line. Enhanced cell adhesion is observed in the coatings, as compared to a coating with a chitosan-ending film and a scrambled arginine-(aspartic acid)-glycine (RDG) biopolymer. The results suggest that such films could be used in the future as smart biomimetic coatings of biomaterials for different biomedical applications, including those in tissue engineering or in controlled delivery systems.

Effect of continued exposition to ethanol on activity of the ammonium and fructose transport systems in Saccharomyces cerevisiae var. ellipsoideus

Ethanol and cycloheximide inhibited the function of the ammonium transport system in growing cultures of Saccharomyces cerevisiae var. ellipsoideus measured as methylamine uptake. The effect was reversible with ethanol and irreversible with the antibiotic. The kinetic data are consistent with a reduction of the number of active carrier molecules located in the plasma membrane. In contrast, neither ethanol nor cycloheximide affected the specific rate of fructose uptake.

Nanobiotechnological approach to engineered biomaterial design: the example of elastin-like polymers

Today, the development of advanced biomaterials is still lacking an appropriate tailored engineering approach. Most of the biomaterials currently used have their origin in materials developed for other technological applications. This lack of adequate biomaterial design is probably due to the peculiar environment where those materials must operate. On the one hand, this environment is dominated by the immune rejection system. On the other hand, the functionality of natural biomolecules is based on complex topological physical-chemical function distributions at the nanometer level. This review presents arguments concerning the role of biotechnology and nanotechnology in the future development of new advanced biomaterials and the potential of these biomaterials as a way to achieve highly biofunctional and truly biocompatible biomaterials for hot areas, such as regenerative medicine and controlled release. Recombinant protein-polymers will be presented as an example of candidates for this new paradigm in biomaterial design and production.

Non-toxic type 2 ribosome-inactivating proteins (RIPs) from Sambucus: occurrence, cellular and molecular activities and potential uses

Ribosome-inactivating proteins (RIPs) are a family of enzymes that trigger the catalytic inactivation of ribosomes. The most known member of the family is the highly poisonous two-chain ricin isolated from Ricinus communis L. Sambucus species contain a number of two-chain RIPs structurally and enzymatically related to ricin which have the noteworthy feature that, having an enzymatic activity on ribosomes, leading to the inhibition of protein synthesis, higher than ricin, they are lacking of the tremendous unspecific toxicity of ricin. Therefore, they have been called non-toxic type 2 RIPs. The most representative and studied members are nigrin b present in the bark of the common (black) elder Sambucus nigra L. and ebulin 1 present in the leaves of the dwarf elder Sambucus ebulus L. The molecular basis for the low unspecific activities of nigrin b and ebulin 1 as compared with ricin seems to be related with single changes of amino acids in the high affinity sugar binding sites of the B chains. These changes determine the intracellular traffic of these proteins and thus the cellular toxicity. Conjugation ofnigrin b or ebulin 1 to either transferrin or monoclonal antibodies provided highly active conjugates targeting cancer. Thus these non-toxic type 2 RIPs are promising tools for cancer therapy.

A single-chain antibody fragment is functionally expressed in the cytoplasm of both Escherichia coli and transgenic plants

Despite the well-known crucial role of intradomain disulfide bridges for immunoglobulin folding and stability, the single-chain variable fragment of the anti-viral antibody F8 is functionally expressed when targeted to the reducing environment of the plant cytoplasm. We show here that this antibody fragment is also functionally expressed in the cytoplasm of Escherichia coli. A gel shift assay revealed that the single-chain variable fragment (scFv) accumulating in the plant and bacterial cytoplasm bears free sulfhydryl groups. Guanidinium chloride denaturation/renaturation studies indicated that refolding occurs even in a reducing environment, producing a functional molecule with the same spectral properties of the native scFv(F8). Taken together, these results suggest that folding and functionality of this antibody fragment are not prevented in a reducing environment. This antibody fragment could therefore represent a suitable framework for engineering recombinant antibodies to be targeted to the cytoplasm.

Functional expression in bacteria and plants of an scFv antibody fragment against tospoviruses

BACKGROUND

Recombinant antibodies expressed in plants ('plantibodies'), directed against crucial antigens and addressed to the right cell compartment, may be able to protect against viral diseases. Moreover, antibody fragments produced in bacteria or plants may provide low cost reagents for immunodiagnosis.

OBJECTIVES

In an attempt to develop genetic immunisation against tomato spotted wilt tospovirus (TSWV), we engineered an scFv fragment starting from a monoclonal antibody (mAb) able to recognise an epitope of the glycoprotein G1 conserved among a large number of tospoviruses. After establishing functional expression in bacteria, we aimed to drive expression of this molecule in the secretory pathway of plants.

STUDY DESIGN

An antibody phage display expression system was used to isolate the correct VH and VL binding regions from the hybridoma secreting the original mAb. To assess functional expression in plant, we first used an epichromosomal expression vector derived from potato virus X (PVX). In this vector the scFv gene was cloned to produce a cytosolic or a secretory protein. For secretion, the signal sequence derived from the polygalacturonase-inhibiting protein (PGIP) of Phaseolus vulgaris was used. Subsequently, the gene encoding the secretory scFv, was used to transform Nicotiana benthamiana plants.

RESULTS

High expression levels of fully active molecule were obtained in Escherichia coli. The engineered molecule retained the binding specificity and dissociation rate constant (k(off)) of the cognate monoclonal antibody. Both PVX-infected and transformed plants expressed fully functional scFv molecules in the secretory pathway.

CONCLUSION

This engineered scFv may be valuable for inexpensive diagnosis, for studying the role of the glycoproteins in virus transmission and, possibly, for a 'plantibody'-mediated resistance to tospoviruses.

A new procedure for the preparation of highly active melonin from the dry seeds of Cucumis melo L

Melon (Cucumis melo L.) dry seeds contain melonin, a protein that strongly inhibits ribosomes from different prokaryotic and eukaryotic sources including those from melon. The protein was purified by a new method to yield highly active and stable protein preparations that involves chromatography through S-Sepharose Fast Flow, CM-Sepharose, Superdex 75 and Mono-S. Melonin shows important functional properties: 1) its inhibitory effects on translation were irreversible; 2) it is a single unglycosylated polypeptide chain with an apparent M(r) of 22000; 3) it degrades RNA in a dose-dependent way without affecting DNA. In the light of present results melonin can be considered as a new plant RNase of unusual properties.

Cusativin, a new cytidine-specific ribonuclease accumulated in seeds of Cucumis sativus L

Dry seeds of Cucumis sativus L. were found to contain a heat-sensitive endoribonuclease of a novel type which we have named cusativin. It was purified to apparent electrophoretic homogeneity by chromatography through S-Sepharose Fast Flow, Sephadex G-75, CM-Sepharose, Superdex 75-FPLC (fast protein liquid chromatography) and Mono S-FPLC. It is a single unglycosylated polypeptide chain with an apparent molecular mass (M(r)) of 22900. Polyclonal anti-cusativin antibodies raised in rabbits only reacted with melonin, the translation inhibitor from Cucumis melo L. Functional, Western blot and enzyme-linked immunosorbent assay (ELISA) analyses indicated that cusativin is present in the coat and cotyledons of dry seeds, but not in embryonic axes. Cusativin is accumulated in maturing seeds. By contrast, after seed germination there is degradation of the cusativin present in cotyledons but not that present in the seed coat. The preference of cusativin for polynucleotide cleavage was poly(C) >> poly(A) acids, poly(U) and poly(G) being unaffected by cusativin. Under the denaturing conditions used for RNA sequencing, cusativin acted only on poly(C). Cusativin proved to be useful for RNA sequencing, in particular, complementing the data obtained with RNase CL3. Cusativin represents a new class of plant RNase and, as far as we are aware, is the first plant enzyme that shows cleavage specificity for cytidine under the denaturing conditions of RNA sequencing.

Isolation and characterization of two new N-glycosidase type-1 ribosome-inactivating proteins, unrelated in amino-acid sequence, from Petrocoptis species

Two new N-glycosidase type-1 ribosome-inactivating proteins (RIPs), denoted petroglaucin 1 and petrograndin, respectively, were isolated from the plants Petrocoptis glaucifolia (Lag.) Boiss sp. viscosa (Rothm.) Lainz and Petrocoptis grandiflora Rothm. These new RIPs do not share H2N-terminal amino-acid sequence homology with petroglaucin (now denoted as petroglaucin 2), the only other type-1 RIP to be isolated from P. glaucifolia (Arias et al. (1992) Planta 186, 532-540). Petroglaucin 1 shares amino-acid sequence homology with RIPs from Cucurbitaceae while petroglaucin 2 and petrograndin do so with saporins and dianthin 30 (Caryophyllaceae). The new RIPs strongly inhibited protein synthesis at subnanomolar concentrations in rabbit reticulocyte lysates and other eukaryotic cell-free systems, but they were inactive on bacterial ribosomes.

Distribution and properties of major ribosome-inactivating proteins (28 S rRNA N-glycosidases) of the plant Saponaria officinalis L. (Caryophyllaceae)

We have studied the distribution of the protein synthesis inhibitory activity in the tissues of Saponaria officinalis L. (Caryophyllaceae). Seven major saporins, ribosome-inactivating proteins, were purified to apparent homogeneity from leaves, roots and seeds using a new procedure of RIPs isolation including ion-exchange and hydrophobic chromatography. They all catalysed the depurination of rat liver ribosomes, which generate the Endo's diagnostic rRNA fragment upon treatment with acid aniline, thus indicating that A4324 from the 28S rRNA has been released (Endo et al. (1987) J. Biol. Chem. 262, 5908-5912). The molecular mass of saporins by SDS-PAGE ranged between 30.2 and 31.6 kDa and by gel-filtration between 27.5 and 30.1 kDa. Amino acid composition and amino-terminal amino acid sequence indicate that all saporins may be considered isoforms. Only two saporins present in roots were glycosylated (SO-R1 and SO-R3). All saporins are very active on cell-free translation systems derived from rabbit reticulocyte lysates, rat liver, Triticum aestivum L., Cucumis sativus L. and Vicia sativa L. However, they are poor inhibitors of an Escherichia coli translation system. They inhibit protein synthesis in HeLa, BeWo and NB 100 cells, HeLa cells being the most resistant. The enzymatic activity of at least one saporin isoform was dependent on magnesium concentration in the standard rat liver cell-free system.

Effects of ribosome-inactivating proteins on Escherichia coli and Agrobacterium tumefaciens translation systems

The effects of 30 type 1 and of 2 (ricin and volkensin) type 2 ribosome-inactivating proteins (RIPs) on Escherichia coli and Agrobacterium tumefaciens cell-free translation systems were compared with the effects on a rabbit reticulocyte translation system. The depurinating activity of RIPs on E. coli ribosomes was also evaluated. Only six type 1 RIPs inhibited endogenous mRNA-directed translational activity of E. coli lysates, with submicromolar 50% inhibitory concentrations. Four RIPs had similar activities on poly(U)-directed phenylalanine polymerization by E. coli ribosomes, and three RIPs inhibited poly(U)-directed polyphenylalanine synthesis by A. tumefaciens ribosomes, with submicromolar 50% inhibitory concentrations.

Isolation and partial characterization of nigrin b, a non-toxic novel type 2 ribosome-inactivating protein from the bark of Sambucus nigra L

The bark of Sambucus nigra L. contains a non-toxic novel type 2 ribosome-inactivating protein that we named nigrin b. In vitro, nigrin b strongly inhibited mammalian protein synthesis but did not affect plant nor bacterial protein synthesis. The protein (M(r) 58,000) contains two subunits, A (M(r) 26,000) and B (M(r) 32,000); linked by disulphide bridge(s). Nigrin b was found to be an rRNA N-glycosidase of the rRNA of intact mammalian ribosomes and shares a very good N-terminal amino-acid sequence homology with the anti-HIV-1 proteins TAP 29 and trichosanthin.

Ebulin 1, a nontoxic novel type 2 ribosome-inactivating protein from Sambucus ebulus L. leaves

A novel type 2 ribosome-inactivating protein (RIP) that we named ebulin 1 has been isolated from leaves of Sambucus ebulus L. (Caprifoliaceae). In vitro ebulin 1 strongly inhibited protein synthesis by rabbit reticulocyte lysates, rat brain, and rat liver cell-free systems but did not affect in vitro plant nor bacterial protein synthesis. Ebulin 1 is composed of two subunits, a catalytic A subunit (M(r) 26,000) and a D-galactose-binding lectin B subunit (M(r) 30,000). Amino-terminal amino acid sequence homology revealed the novelty that the ebulin 1 A-chain shares a high degree of homology not with the A-chain of other type 2 RIPs but rather with the Cucurbitaceae type 1 RIP briodin S and the anti-human immunodeficiency virus type I proteins trichosanthin and TAP 29. Upon treatment with acid aniline the rRNA from ebulin 1-treated rabbit reticulocyte ribosomes released the RNA fragment which is diagnostic of RIP catalytic action. Ebulin 1 was nontoxic to mice up to 2 mg/kg of body weight and did not inhibit protein synthesis in cultured NHC human epithelial cells which are highly sensitive to ricin.

Molecular mechanism of inhibition of mammalian protein synthesis by some four-chain agglutinins. Proposal of an extended classification of plant ribosome-inactivating proteins (rRNA N-glycosidases)

The four chain agglutinins from Abrus precatorius, Viscum album and Ricinus communis promote depurination of the 28 S rRNA from rabbit reticulocyte ribosomes characteristic of the common ribosome-inactivating proteins (RIPs). These agglutinins inhibited mammalian protein synthesis at nanomolar concentrations but they do not affect plant protein synthesis under the same conditions. Therefore, they should also be considered as true RIPs but of a new class, the four-chain RIPs. An extended classification of RIPs is presented based on the former one from Stirpe et al. [Bio/technology 10 (1992) 405-412].

A Cucumis sativus cell-free translation system: preparation, optimization and sensitivity to some antibiotics and ribosome inactivating proteins

A cell-free translation system was prepared from 3- to 5-day-old embryonic axes of gherkin (Cucumis sativus L.). The system was optimized for Mg²⁺ , K⁺ , NH⁺₄ , high speed supernatants, tRNA mixture from wheat germ, time and temperature. The system translates efficiently both endogenous mRNA (using a 30000 g supernatant) and polyuridylic acid (using either a 30000 g supernatant or a 100000 g supernatant supplemented with purified ribosomes). Translation by gherkin ribosomes was inhibited by several well-known eukaryotic inhibitors, antibiotics and ribosome-inactivating proteins. A translational inhibitory activity found in Cucumis sativus L. dry seeds acted on polypeptide synthesis carried out by cell-free systems from several mammals and plants, including gherkin embryonic axes. Our results indicate that the inhibitor is located in the seed bark and cotyledons, and is either blocked or absent in the embryonic axes, thus allowing the isolation of active gherkin ribosomes. The presence of the putative inhibitor appeared to be unevenly distributed in developing plants.

Molecular action of the type 1 ribosome-inactivating protein saporin 5 on Vicia sativa ribosomes

The type 1 ribosome-inactivating protein (RIP) saporin 5 isolated from seeds of Saponaria officinalis L. strongly inhibited translation carried out by Vicia sativa L. purified ribosomes. The toxin multidepurinated V. sativa rRNA, which upon treatment with acid aniline releases several RNA fragments including an RNA fragment of approximately 370 nucleotides the 5'-end sequence of which was 5'-GAGGAACG-3'.

Messenger-dependent action of the pokeweed antiviral protein and fusidic acid on in vitro Vicia sativa L. translation

Plant ribosome sensitivity to either pokeweed antiviral protein (PAP) or fusidic acid has been investigated using a highly coupled translation system obtained from Vicia sativa L., a plant that lacks ribosome-inactivating protein activity. Protein synthesis directed by endogenous messengers was more sensitive to PAP than synthesis of polyphenylalanine directed by polyuridylic acid. Conversely, the effects of fusidic acid were the highest in polyphenylalanine synthesis. Additionally, the concentration of magnesium ions during translation also played a determinant role in the extent of inhibition by both PAP and fusidic acid. The effects seem to be exerted on the interaction of the translational elongation factor 2 with the ribosome.

Isolation and partial characterization of a new ribosome-inactivating protein from Petrocoptis glaucifolia (Lag.) Boiss

Petrocoptis glaucifolia, a paleoendemic member of the Caryophyllaceae from the North of Spain, was found to contain at least five proteins that inhibit protein synthesis in a rabbit reticulocyte lysate. One of them, for which the name petroglaucin is proposed, was purified to apparent electrophoretic homogeneity by chromatography through S-Sepharose Fast Flow, Sephadex G-75 and CM-Sepharose Fast Flow. The apparent Mr of the preparation was 27500. This protein does not contain appreciable glycan chains and displays 45.8% of NH2-terminal amino-acid sequence homology with some ribosome-inactivating proteins from Saponaria officinalis, another member of the Caryophyllaceae. Petroglaucin shows the following functional properties: (i) it strongly inhibits the rabbit-reticulocyte-lysate system and Vicia sativa cell-free extracts, both coded by endogenous messengers, and also inhibits poly(U)-directed polyphenylalanine synthesis by Vicia sativa cell-free extracts and purified rat-liver ribosomes; (ii) it shows much less inhibitory capacity in wheat-germ, Cucumis sativus and rat-liver cell-free systems coded by endogenous messengers; (iii) the inhibitory effects on purified rat-liver ribosomes were irreversible; (vi) it promotes the release of adenine from purified rat-liver ribosomes. The total activity of this translational inhibitor has been found to increase up to 11-fold during its purification, indicating that some regulatory factor that normally blocks the translational inhibitory activity of the ribosome-inactivating protein in crude extracts of the plant is removed during purification.

Changes in sensitivity of in vitro rat brain protein synthesis to the acute action of ethanol and isopropanol as a consequence of the long-term ingestion of isopropanol

Long-term treatment of rats with isopropanol in the drinking water results in a change or process of adaptation occurring in in vitro brain protein synthesis which increases the resistance of the ribosomal machinery to the acute effect of either ethanol or isopropanol. Such an increase was observed both in the system coded by endogenous messenger and in the system coded by polyuridylic acid. In both translation systems, the adaptation seems to affect the ribosomal step of polypeptide chain elongation. The increase in resistance to the alkanols apparently did not affect the inhibitory action of puromycin, fusidic acid and cycloheximide on the ribosome.

Effect of L-azetidine 2-carboxilic acid on the activity of the general amino-acid permease from Saccharomyces cerevisiae var. ellipsoideus

Addition of the L-proline analogue L-azetidine 2-carboxylic acid to growing cultures of Saccharomyces cerevisiae var. ellipsoideus promoted fast deactivation of the general aminoacid permease, measured as L-valine uptake, without an immediate decrease in the growth rate. Cells preincubated with the analogue for 3 h were unable to restore either growth ability or general aminoacid permease activity in analogue-free medium. Eadie-Hofstee plots of L-valine uptake in the presence of the analogue are consistent with a strong reduction in the number of active molecules of the general amino-acid permease located in the plasma membrane. Inhibitory effects on protein synthesis were seen after preincubations of the yeast with the analogue for 3 h although a 30 min preincubation had no effect.