Successful implementation of safe practice for adult intravenous push medication in a tertiary care hospital: determination of stability of four intravenous antibiotics in syringes

In 2017, a severe shortage of infusion bags resulted in a paradigm change in medication administration practice from intermittent infusion to intravenous push. The Institute for Safe Medication Practices proposed safe practice guidelines for adult intravenous push medications. A different study showed that ready-to-administer medication prepared in the sterile area of a pharmacy reduces the risk of harm, nurses' time for medication administration and the cost of medications. Based on the recommendation of the Institute for Safe Medication Practices, we decided to conduct a pilot study on the implementation of sterile compounding and administration of intravenous push medication in adult patients admitted to the hospital. In the study, the stability of five intravenous push antibiotic syringes was also determined in the syringes.

Integrity performance assessment of a closed system transfer device syringe adaptor lock as a terminal closure for Luer-Lock syringes

OBJECTIVES

To investigate the container closure integrity of a closed system transfer device syringe adaptor lock in combination with disposable Luer-Lock syringes as the terminal closure device. The UK National Health Service (NHS) Pharmaceutical Quality Assurance Committee (PQAC) requires syringe integrity data for final storage devices of aseptic products such as chemotherapy drugs when prepared in advance and stored before use, as is standard practice for dose banded drugs. The assessment comprised both physical and microbial integrity testing of the combination closed system/Luer-Lock syringe containers at syringe sizes of 1 mL, 20 mL, and 50 mL.

METHODS

Integrity testing was performed as described in the NHS Pharmaceutical Quality Assurance Committee yellow cover document, second edition 2013 'Protocols for the Integrity Testing of Syringes', with Chemfort (Simplivia, IL) syringe adaptor lock (SAL) devices as replacement for sterile blind hubs. Microbiological integrity was assessed according to method 1 part 1.4 using Brevundimonas diminuta at 32°C for up to 14 days of contact time. Two positive control devices per syringe size were tested using a blind hub cap as closure which was loosened before the test. Physical integrity was assessed using method 3 of the yellow cover document which is a dye intrusion method. Dye intrusion was assessed both visually and using a validated ultraviolet-visible spectrophotometer method. For each size/batch of test articles a positive control device (n=1) was assessed using a wire wrapped around the syringe plunger tip deliberately compromising integrity. Negative controls for each size (n=1) consisted of devices not immersed in methylene blue dye.

RESULTS

Chemfort syringe adaptor lock/Luer-Lock syringe combinations were shown to be: (1) free of microbiological contamination after 14 days of contact time (n=60); and (2) free of dye intrusion at all syringe sizes tested (n=61 in total). The data demonstrate 100% closure integrity of the final container system when the Chemfort syringe adaptor lock replaces the syringe hub as the terminal closure device. All positive control devices demonstrated system suitability as container integrity was compromised in all positive control tests. All negative controls were negative for microbial and dye intrusion.

CONCLUSIONS

Syringe adaptor lock components complied with the NHS Pharmaceutical Quality Assurance Committee yellow cover document syringe integrity requirements when used as the terminal closure of Luer-Lock disposable syringes from 1 mL up to 50 mL. Therefore, syringe adaptor lock (Chemfort) can be used as the terminal closure system for pre-filled syringes of chemotherapeutic drug products prepared in advance in UK NHS pharmacy technical services.

Holistic Extractables and Leachables Program: Evaluations of Prefilled Syringe Systems for Biotechnology Products

Prefilled syringes (PFS) are a container and delivery device of choice for storing and administering therapeutic protein products to patients. Addressing concerns and regulatory expectations related to the risk to biologic drug product quality and patient safety from PFS requires implementation of an extractable and leachable program based on understanding of materials, risk assessment, review of existing literature, and testing supported by a sound scientific foundation. Extractables and leachables data generated as part of a thorough and holistic program are presented for five PFS systems, including glass and plastic syringes filled with 12 biologic drug products encompassing the implementation of traditional and single-use biotechnology manufacturing processes. The comprehensive extractables and leachables data presented demonstrate and substantiate a holistic extractable and leachable program designed to ensure product quality and patient safety.

Prefilled Cyclic Olefin Sterilized Syringes of Norepinephrine Injection Solution Do Not Need to Be Stabilized by Antioxidants

Norepinephrine is a potent α-sympathomimetic drug which plays an important role in the acute treatment of hypotension and shock. Commercially available norepinephrine solutions contain sodium metabisulfite (Na2S2O5) as an antioxidant. However, prefilled cyclic olefin polymer syringes are not compatible with sodium metabisulfite. The aim of this study was to develop a new formulation of 0.1-mg/mL norepinephrine solution without sodium metabisulfite which is chemically stable and sterile and can be stored in prefilled polymer syringes. Formulation studies were performed with 0.1-mg/mL norepinephrine solution with 0, 0.05, or 0.1% ascorbic acid added as antioxidant. The syringes were filled under nitrogen gassing, stored at 20 ± 5°C, and protected from daylight. Based on the formulation test results, the final formulation was defined and stability testing at 20 ± 5°C was performed measuring norepinephrine concentration, pH, clarity, color of the solution, subvisible particles, and sterility at time intervals up to 12 months. The norepinephrine concentrations at t = 22 weeks were 100.4%, 95.4%, and 92.2% for the formulations with no ascorbic acid and with 0.05% and 0.10% ascorbic acid, respectively. Three batches for the stability study were produced containing norepinephrine, sodium edetate, sodium chloride, and water for injections filled under nitrogen gassing and stored at 20 ± 5°C. Norepinephrine concentrations were respectively 98.8%, 98.6%, and 99.3% for batches 1, 2, and 3 at t = 12 months. It can be concluded that norepinephrine (0.1 mg/mL) solution without metabisulfite is stable for at least 12 months at room temperature when protected from daylight.

Quantification of Silicone Oil and Its Degradation Products in Aqueous Pharmaceutical Formulations by 1H-NMR Spectroscopy

During the past years, there has been an increasing focus on the presence of silicone oil as a contaminant in pharmaceutical formulations kept in prefilled syringes (PFSs). As the PFSs are coated on the inner wall with silicone oil (polydimethylsiloxane), there is a potential risk that the oil can migrate from the inner surface of the primary packing material into the aqueous solution. Several studies have demonstrated that presence of silicone oil as droplets in a high-concentrated protein formulation can cause protein aggregation. Hence, because the use of silicone-coated primary packing material for protein formulations are increasing, the call for an easy and quantitative method for determination of silicone oil and its degradation products in pharmaceutical formulations is therefore needed. Several analytical techniques have in the past been developed with the aim of detecting the presence of silicone oil and degradation products hereof. Most of these methods require hydrolyzation, derivatization, and extraction steps followed by, for example, gas chromatography-mass spectrometry analysis. Applying these methods can cause a loss in detection or an overestimation of the hydrolytic degradation products of silicone oil, that is, trimethylsilanol and dimethylsilanediol. The 2 silanols are highly hydrophilic and prefers the aqueous environment. Analysis of an aqueous formulation obtained from a PFS by ¹H-NMR spectroscopy provides data about the content and levels of silicone oil and the 2 silanols even in levels below 10 ppm. The ¹H-NMR method offers an easy and direct, quantitative measurement of samples intended for clinical use and samples kept at elevated temperature for a prolonged time (i.e., stability studies). The result of the study presented here showed dimethylsilanediol to be the main silicone compound present in the aqueous formulation when kept in baked-on PFSs. The degradation product dimethylsilanediol, in full accordance with expected hydrolytic degradation of silicone oil, increased during storage and with elevated temperature. In addition, the method can be applied to aqueous samples where polydimethylsiloxane has been added as, for example, the major constituent of antifoam.

Nonlinear Flow Sensor Calibration with an Accurate Syringe

Flow sensors are required for monitoring patients on mechanical ventilation and in respiratory research. Proper calibration is important for ensuring accuracy and can be done with a precision syringe. This procedure, however, becomes complex for nonlinear flow sensors, which are commonly used. The objective of the present work was to develop an algorithm to allow the calibration of nonlinear flow sensors using an accurate syringe. We first noticed that a power law equation could properly fit the pressure-flow relationship of nonlinear flow sensors. We then developed a software code to estimate the parameters for this equation using a 3 L syringe (calibration syringe). Finally, we tested the performance of a calibrated flow sensor using a different 3 L syringe (testing syringe) and a commercially available spirometer. After calibration, the sensor had a bias ranging from −1.7% to 3.0% and precision from 0.012 L to 0.039 L for volumes measured with the 3 L testing syringe. Calibrated sensor performance was at least as good as the commercial sensor. This calibration procedure can be done at the bedside for both clinical and research purposes, therefore improving the accuracy of nonlinear flow sensors.

Sterile Basics of Compounding: Relationship Between Syringe Size and Dosing Accuracy

The purpose of this study was to investigate the accuracy and reproducibility of a 2-mL volume injection using a 3-mL and 10-mL syringe with pharmacy student compounders. An exercise was designed to assess each student's accuracy in compounding a sterile preparation with the correct 4-mg strength using a 3-mL and 10-mL syringe. The average ondansetron dose when compounded with the 3-mL syringe was 4.03 mg (standard deviation ± 0.45 mg), which was not statistically significantly different than the intended 4-mg desired dose (P=0.497). The average ondansetron dose when compounded with the 10-mL syringe was 4.18 mg (standard deviation + 0.68 mg), which was statistically significantly different than the intended 4-mg desired dose (P=0.002). Additionally, there also was a statistically significant difference in the average ondansetron dose compounded using a 3-mL syringe (4.03 mg) and a 10-mL syringe (4.18 mg) (P=0.027). The accuracy and reproducibility of the 2-mL desired dose volume decreased as the compounding syringe size increased from 3 mL to 10 mL.

A Comparison of Protein Stability in Prefillable Syringes Made of Glass and Plastic

The development of protein therapeutics requires stabilization of these labile molecules during shipment and storage. Biologics, particularly monoclonal antibodies, are frequently packaged at high concentration in prefillable syringes traditionally made of glass. However, some biologics are unstable in glass due to sensitivity to silicone oil, tungsten, glue, or metal ions. Syringes made from the plastic cyclic olefin polymer, Daikyo Crystal Zenith® (CZ), with a Flurotec-laminated piston, have none of these issues. This study compared the stability of several proteins including biotherapeutics when stored up to 14 months at 5 °C and 25 °C in prefillable siliconized syringes made of glass or silicone oil-free CZ syringes, and when subjected to mild agitation by end-over-end rotation at room temperature. At each time point, proteins were analyzed by several techniques including turbidity, size exclusion high-performance liquid chromatography, reversed phase high-performance liquid chromatography, ion-exchange chromatography, electrophoresis, and light scattering to monitor changes in aggregation and degradation. The results show that proteins have comparable stability when stored in glass syringes or in syringes made of CZ sterilized by E-beam or autoclave. In addition, proteins stressed by agitation were generally more stable and aggregated less in syringes made of CZ than in ones made of glass.LAY ABSTRACT: Biotherapeutic protein drugs such as monoclonal antibodies are frequently packaged at high concentration in prefillable syringes, which allows the drug to be directly administered by the patient or caregiver. Protein drugs, or biologics, can be unstable, and may aggregate, particularly when shaken. These aggregates can be immunogenic, stimulating the body's immune system to produce antibodies that can reduce the drug's efficacy. Although prefillable syringes are traditionally made of glass, some biologics are unstable in glass syringes due to the presence of substances used in their manufacture, including silicone oil, which is necessary for lubricity. Syringes made from the plastic cyclic olefin polymer, Daikyo Crystal Zenith® (CZ), have none of these issues. This study compared the stability of several biotherapeutic proteins when stored up to 14 months at 5 °C and 25 °C in prefillable siliconized syringes made of glass or silicone oil-free CZ syringes, and when mildly agitated at room temperature. Proteins were analyzed by several techniques to detect changes in aggregation and degradation. The results show that biotherapeutic proteins have similar stability whether stored in syringes made of glass or CZ. In addition, proteins subjected to agitation were generally more stable and aggregated less in CZ syringes than in glass syringes.

InfuShield: a shielded enclosure for administering therapeutic radioisotope treatments using standard syringe pumps

The administration of radionuclide therapies presents significant radiation protection challenges. The aim of this work was to develop a delivery system for intravenous radioisotope therapies to substantially moderate radiation exposures to staff and operators. A novel device (InfuShield) was designed and tested before being used clinically. The device consists of a shielded enclosure which contains the therapeutic activity and, through the hydraulic action of back-to-back syringes, allows the activity to be administered using a syringe pump external to the enclosure. This enables full access to the pump controls while simultaneously reducing dose to the operator. The system is suitable for use with all commercially available syringe pumps and does not require specific consumables, maximising both the flexibility and economy of the system. Dose rate measurements showed that at key stages in an I mIBG treatment procedure, InfuShield can reduce dose to operators by several orders of magnitude. Tests using typical syringes and infusion speeds show no significant alteration in administered flow rates (maximum of 1.2%). The InfuShield system provides a simple, safe and low cost method of radioisotope administration.

The use of metal or plastic needles in continuous subcutaneous infusion in a hospice setting

Objectives. Battery-driven portable syringe drivers are a convenient method for administering many drugs by continuous subcutaneous infusion (CSCI) to patients who cannot swallow medications. At the St. Clare Hospice, nurses usually use plastic needles to minimize needlestick injury but sometimes have patients transferred to metal needles. This study retrospectively examines this practice and its effectiveness.

Methods. The duration of audit was four months. During this period, there were 40 patients (23 women, 17 men), who required their medications delivered by CSCI. A total number of 74 sites were used. Metal or plastic needle CSCIs connected with one-hour release Graseby ® Syringe Drivers were used. The syringes were set to deliver 2 mm/hour. The maximum volume syringe used was 50 ml. The data were collected retrospectively.

Analysis and results. Sixteen patients (21.6 percent) developed minor complications (13 plastic, three metal). Among them, 16 showed inflammation. Two patients (3.5 percent) showed slight bleeding. Only one patient (1.7 percent) showed local infection (metal). In 14 patients (18.9 percent), the needle was reinserted due to various reasons, including needles pulled out by patients or needles falling out due to unknown reasons. There were no needlestick injuries reported, and the staff members reported that all problems encountered were easy to identify and resolve.

Conclusion. Plastic needle CSCI prevents needlestick injury and gives minimum distress to the patients. More research is needed to determine the local side effects of drugs used and the strategies to resolve these problems.

Characterization of Protein Aggregating Tungstates: Electrospray Mass Spectrometry Analysis of Extracts from Prefilled Syringes and from Tungsten Pins Used in the Manufacture of Syringes

Glass prefilled syringes are increasingly becoming a container of choice for storing and administering therapeutic protein products to patients. Tungsten leaching from a PFS is known to induce protein particle formation, and the source was traced to the tungsten pins used in the manufacturing process of the syringe barrels. Study of the tungstates present in extracts from both tungsten pins used in the syringe manufacturing process and from single syringes from various suppliers was undertaken. Electrospray mass spectrometry was chosen as a technique with the sensitivity to characterize tungstates at levels (∼1 ppm of elemental tungsten) observed in single syringes. Extraction solvents were chosen to simulate the range (pH 4.0-7.0) typically used for therapeutic protein formulation. A commercial product formulation buffer was also used as an extraction solution to characterize tungstate species used for tungsten spiking studies of protein. All pin and syringe extracts from various manufacturers were similar in regards to containing stable Na/K containing lacunary polytungstate ([W11O39](7-)) species, which were the main species present in syringe extracts and are different than the metatungstate ([W12O39](6-)) species identified in commercially available sodium polytungstate and as the main species in pin extracts. These stable Na/K containing polytungstates species present in pin and syringe extracts are likely formed during the glass manufacturing process at >400 °C and may have the capability to subsequently form larger polytungstate complexes.

LAY ABSTRACT

Glass prefilled syringes are a type of container used for storing and administering biotechnology medicines to patients. The manufacturing process for the syringes may lead to very low levels of the metal tungsten being present in the syringes, and thus in the medicine stored in the syringes. The presence of tungsten in certain biotechnology medicines has been shown to cause changes to the medicine. Understanding something that can cause a medicine to change is an important part of producing safe and effective medicines for patients. The study described in this article sought to increase understanding by characterizing the form of tungsten observed in syringes from a number of vendors. Study of the tungsten present in syringes from four vendors indicates the same form of tungsten is observed regardless of the vendor. The study also found that the form of tungsten differed from that expected.

Non-destructive vacuum decay method for pre-filled syringe closure integrity testing compared with dye ingress testing and high-voltage leak detection

In reaction to the limitations of the traditional sterility test methods, in 2008, the U.S. Food and Drug Administration issued the guidance "Container and Closure System Integrity Testing in Lieu of Sterility Testing as a Component of the Stability Protocol for Sterile Products" encouraging sterile drug manufacturers to use properly validated physical methods, apart from conventional microbial challenge testing, to confirm container closure integrity as part of the stability protocol. The case study presented in this article investigated the capability of four container closure integrity testing methods to detect simulated defects of different sizes and types on glass syringes, prefilled both with drug product intended for parenteral administration and sterile water. The drug product was a flu vaccine (Agrippal, Novartis Vaccines, Siena, Italy). Vacuum decay, pharmacopoeial dye ingress test, Novartis specific dye ingress test, and high-voltage leak detection were, in succession, the methods involved in the comparative studies. The case study execution was preceded by the preparation of two independent sets of reference prefilled syringes, classified, respectively, as examples of conforming to closure integrity requirements (negative controls) and as defective (positive controls). Positive controls were, in turn, split in six groups, three of with holes laser-drilled through the prefilled syringe glass barrel, while the other three with capillary tubes embedded in the prefilled syringe plunger. These reference populations were then investigated by means of validated equipment used for container closure integrity testing of prefilled syringe commercial production; data were collected and analyzed to determine the detection rate and the percentage of false results. Results showed that the vacuum decay method had the highest performance in terms of detection sensitivity and also ensured the best reliability and repeatability of measurements. An innovative technical solution, preventing possible prefilled syringe plunger movement during container closure integrity testing execution, is presented as well.

LAY ABSTRACT

The growing need to meet sterile drug products' regulatory, quality, and safety expectations has progressively driven new developments and improvements both in container closure integrity testing methods and in the respective equipment, over the last years. Indeed, container closure integrity testing establishes the container closure system capability to provide required protection to the drug product and to demonstrate maintenance of product sterility over its shelf life. This article describes the development of four container closure integrity testing approaches for the evaluation of glass prefilled syringe closure integrity, including two destructive (pharmacopoeial and Novartis specific dye ingress test) and two non-destructive (vacuum decay and high-voltage leak detection) methods. The important finding from the validation of comparative studies was that the vacuum decay method resulted in the most effective, reliable and repeatable detection of defective samples, whether the defect was exposed to sterile water, to drug product, or to air. Complete sets of known defects were created for this purpose (5 μm, 10 μm, 20 μm certified leakages by laser drilled holes and capillary tubes). All investigations and studies were conducted at Bonfiglioli Engineering S.r.l. (Vigarano Pieve, Ferrara, Italy) and at Novartis Vaccines (Sovicille, Siena, Italy).

Internalized stigma and sterile syringe use among people who inject drugs in New York City, 2010-2012

BACKGROUND

Little is known on the effect of stigma on the health and behavior of people who inject drugs (PWID). PWID may internalize these negative attitudes and experiences and stigmatize themselves (internalized stigma). With previous research suggesting a harmful effect of internalized stigma on health behaviors, we aimed to determine socio-demographic characteristics and injection risk behaviors associated with internalized PWID-related stigma in New York City (NYC).

METHODS

Three NYC pharmacies assisted in recruiting PWID. Pharmacy-recruited PWID syringe customers received training in recruiting up to three of their peers. Participants completed a survey on injection behaviors and PWID-related stigma. Among HIV-negative PWID (n=132), multiple linear regression with GEE (to account for peer network clustering) was used to examine associations with internalized PWID-related stigma.

RESULTS

Latinos were more likely to have higher internalized stigma, as were those with lower educational attainment. Those with higher internalized stigma were more likely to not use a syringe exchange program (SEP) recently, although no association was found with the recent use of pharmacies for syringes. Lastly, higher internalized stigma was related to less than 100% use of pharmacies or SEPs for syringe needs.

CONCLUSIONS

These data suggest that PWID with higher internalized stigma are less likely to consistently use sterile syringe sources in urban settings with multiple sterile syringe access points. These results support the need for individual- and structural-level interventions that address PWID-related stigma. Future research is needed to examine why PWID with higher internalized stigma have less consistent use of public syringe access venues.

[Patient safety can be ensured in clinical microsystems]

Patients, health-care professionals and the public expect safe health care. The system, however, is not safe and patients are being harmed. Workplace and organizational conditions and human factors contribute to these harms and a system approach is needed to avoid them. In clinical microsystems (CMS), the frontline units of health care, staff and patients can make care safer by learning about their system, its processes, members and purposes. Approaches from patient safety should be integrated in the daily work of every member of the CMS to reduce risk, implement safe practices and learn from errors. We summarize methods for use in CMS and offer ideas for fostering a proactive culture of patient safety.

Changing practice for safe insulin administration

Insulin is a life-saving medication but, if wrongly administered, it can cause death or severe harm. Errors in insulin administration are common, including the inappropriate use of intravenous syringes. We surveyed all clinical areas in our trust to identify types of syringes and needles available and how these were stored and distinguished from IV syringes. Based on these results, we developed recommendations to promote safety and good practice and are standardising insulin syringes throughout the trust.

Administration of substances to laboratory animals: equipment considerations, vehicle selection, and solute preparation

Administration of substances to laboratory animals requires careful consideration and planning to optimize delivery of the agent to the animal while minimizing potential adverse experiences from the procedure. The equipment selected to deliver substances to animals depends on the length of the study and the nature of the material being administered. This selection provides a significant opportunity for refining animal treatment. Similarly, when substances are administered as solutions or suspensions, attention should be given to selection of vehicles and methods used for preparing the solutions and suspensions. The research team, veterinarian, technical personnel, and IACUC members should be aware of reasons underlying selection of equipment for substance delivery and should consider carefully how substances will be prepared and stored prior to administration to animals. Failure to consider these factors during experimental planning may result in unintentional adverse effects on experimental animals and confounded results.

Compatibility testing of two types of pen needles with a range of injection pens for diabetes medication

Compatibility of two types of needles with a variety of durable and prefilled injection pens for diabetes medication was tested by attaching the needles according to ISO 11608-2 and verifying penetration into the cartridge using air shots and two-dimensional X-rays. NovoFine* and NovoFine Autocover† attached correctly to 20 and 19 out of 21 pen types, respectively. Neither needle type attached to Diapen 3.1/3.2, while NovoFine Autocover attached to most, but not all of OptiSet pens.

Ongoing use of conventional devices and safety device activation rates in hospitals in Ontario, Canada

This study assessed voluntary compliance with the use of sharp safety devices in lieu of conventional ones and the activation status of these safety devices: VanishPoint syringes, Terumo Surshield butterflies, and Insyte Autoguard IV catheters. Sharps disposal containers from various wards in three private, not-for profit, university-affiliated Ontario hospitals were audited during 9 days in August 2007. In the 149 audited sharps containers, 55% of all syringes found were conventional compared with 45% that were safety syringes. In the three hospitals, the percentages of conventional (non-safety) vs. safety syringes found in used sharps containers were as follows, respectively: (i) 72% conventional and 28% safety, (ii) 55% conventional and 45% safety, and (iii) 65% conventional and 35% safety. In addition, it was found that 77% of 2131 Terumo butterflies, 97% of 1117 Insyte Autoguard IV catheters, and 87% of 4897 VanishPoint syringes in the containers had been activated. This study, carried out approximately 1 year before it was legally required to use safety instead of sharp conventional devices, found that most devices in use were conventional ones. It was also found that only the activation rate for the safety IV device was acceptable.

Intrathecal catheter-syringe adaptor for short-term intrathecal analgesia with an externalized pump: a case report

BACKGROUND

In most patients, cancer pain is effectively treated with conservative medical management consisting of oral and/or transdermal analgesics. Cancer patients tend to fail conservative medical management near the end of their life expectancy, thus requiring alternative routes of analgesia such as intravenous, epidural, or intrathecal. The intrathecal route provides the most effective analgesia due to the close proximity of the opioid receptors in the spinal cord. Though there are many techniques that exist for intrathecal drug delivery, complications can limit effectiveness such as infection, bleeding, cerebrospinal fluid (CSF) leaks, post-dural puncture headaches (PDPH), pump and/or catheter malfunctions, or limitations of technical expertise. Therefore, an important goal in palliative cancer pain therapy is to use equipment that is going to have the fewest number of complications and will be the most familiar to the health care providers. We describe the combination of the Medtronic Indura 1P catheter, which has the least catheter-related complications and can be used with any external drug infusion pump. These are regular infusion pumps that the health care workers are familiar with so they can provide excellent and efficient service to the patient.

METHODS

In an operating room, the intrathecal catheter was placed using sterile technique under fluoroscopic guidance. The epidural space was identified with loss of resistance technique. Then the introducer needle (supplied in the Indura 1P catheter kit) was advanced until free-flowing CSF was obtained. The spinal catheter was advanced into the intrathecal space through the introducer needle to lumbar 2-3 level. The catheter was tunneled subcutaneously 10 cm lateral to the catheter exit site. A syringe filling device was inserted into the catheter opening and was secured with silk suture. A luer lock syringe was attached to the syringe filling device and CSF was aspirated. The syringe filling device was capped and later attached to an external drug infusion pump.

RESULTS

We report the successful use of the Medtronic Indura 1P, one piece intrathecal catheter, connected to the external drug pump for a 3 week period in a patient with metastatic cervical cancer for palliative pain control.

LIMITATIONS

Case report only.

CONCLUSION

This technique is simple to perform by pain specialists. The catheter modification allows the use of the Medtronic intrathecal catheter with standard external drug infusion pumps. This facilitates the patient's care in the hospice setting.

Analysis of biopharmaceutical market-appropriate plastic syringe barrel for extractables

A study was designed to evaluate a new syringe system developed specifically for sensitive pharmaceutical and biopharmaceutical drug products. An in-depth review of the extractables portion of this program is presented and includes data generated by liquid chromatography-mass spectroscopy, gas chromatography-mass spectroscopy, ion chromatography, and inductively coupled plasma of the Crystal Zenith barrel before and after sterilization. One leachable was identified after e-beam irradiation processing. This leachable, identified as an organic acid species, was then evaluated from a safety assessment viewpoint. The details of this program and associated results are explained in this report.

Reuse prevention syringes for reconstitution of lyophilized vaccines: Operational study and UNICEF plans for expanding introduction

Since the 1990s, the United Nation's Children's Fund has encouraged injection safety for immunizations through bundling vaccines with appropriate amounts of supporting equipment and by supplying autodisable (AD) syringes for injections. However, poor vaccine reconstitution practices continue to be reported worldwide. By 2009, UNICEF will begin to phase out the distribution of standard disposable syringes for vaccine reconstitution and replace them with reuse prevention (RUP) syringes, with a full transition expected by the end of 2010. A field evaluation in Indonesia was conducted to identify introduction requirements, issues with healthcare worker training and acceptance, and RUP syringe performance and safety. Managers and health workers felt that RUP syringes improved injection safety and fit easily into country logistical systems. Healthcare workers felt they were intuitive to use, but recommended special training. The integration of RUP reconstitution syringes by UNICEF could increase injection safety by preventing the reuse of syringes and reducing vaccine contamination.

Particulate and microbial contamination in in-use admixed intravenous infusions

We compared particulate and microbial contamination in residual solutions of peripheral intravenous admixtures after the termination of drip infusion between intravenous fluids admixed with glass ampoule drugs and those admixed with pre-filled syringe drugs. The mean number of particles>or=1.3 microm in diameter per 1 ml of residual solution was 758.4 for fluids (n=60) admixed with potassium chloride in a glass ampoule (20 ml volume), 158.6 for fluids (n=63) admixed with potassium chloride in a pre-filled syringe (20 ml volume), 736.5 for fluids (n=66) admixed with sodium chloride in a glass ampoule (20 ml volume), 179.2 for fluids (n=15) admixed with sodium chloride in a pre-filled syringe (20 ml volume), 1884.5 in fluids (n=30) admixed with dobutamine hydrochloride in 3 glass ampoules (5 ml volume), and 178.9 (n=10) in diluted dobutamine hydrochloride in pre-filled syringes (50 ml volume: For these samples alone, particulate and microbial contamination were evaluated in sealed products.) Thus, for potassium chloride or sodium chloride for injection, the number of particles>or=1.3 microm in diameter in the residual intravenous solution was significantly higher for fluids admixed with glass ampoule drugs than for those admixed with pre-filled syringe drugs (p<0.0001). For dobutamine hydrochloride for injection, the number of particles>or=1.3 microm in diameter in the residual intravenous solution was estimated to be higher for fluids admixed with its glass ampoule drug than for those admixed with its pre-filled syringe drug. Observation of the residual solutions of fluids admixed with potassium chloride, sodium chloride, or dobutamine hydrochloride in glass ampoules using an electron microscope with an X-ray analyzer showed glass fragments in each residual solution. Therefore, for the prevention of glass particle contamination in peripheral intravenous admixtures, the use of pre-filled syringe drugs may a useful method. No microbial contamination was observed in any of the residual solutions of 5 types of admixture.

Changes in injecting practices associated with the use of a medically supervised safer injection facility

Injection drug users (IDUs) are vulnerable to serious health complications resulting from unsafe injection practices. We examined whether the use of a supervised safer injection facility (SIF) promoted change in injecting practices among a representative sample of 760 IDUs who use a SIF in Vancouver, Canada. Consistent SIF use was compared with inconsistent use on a number of self-reported changes in injecting practice variables. More consistent SIF use is associated with positive changes in injecting practices, including less reuse of syringes, use of sterile water, swabbing injection sites, cooking/filtering drugs, less rushed injections, safe syringe disposal and less public injecting.

A pilot study to measure the compressive and tensile forces required to use retractable intramuscular safety syringes

BACKGROUND

A pilot study was conducted at the Tampa Veterans Administration Patient Safety Center. The objective was to determine the forces required to operate retractable safety syringes to evaluate potential adverse occupational health and patient safety issues.

METHODS

Four brands (100 each) of retractable syringes were tested, using a digital force gauge, in air and in a simulated patient material (SPM). Compressive and tensile forces were measured while activating the retraction mechanism and withdrawing saline into the syringe barrel, respectively.

RESULTS

The mean compressive force was greater in SPM than in air in all 4 devices. There was a statistically significant compressive force difference between activation in air and SPM in devices 1 and 2 (P </= .05). The tensile forces for all devices were lower than the compressive forces. Analysis of variance was used to compare the groups, and the results showed that the means were significantly different (P < .001).

CONCLUSION

This pilot study has implications for device selection, training for users, design issues for manufacturers, and patient safety, as well as potential for future needlestick and ergonomic injuries. We recommend replication of this study with a computer-controlled force testing apparatus, and by testing multiple needle and syringe sizes.

Efficient measurement of endogenous neurotransmitters in small localized regions of central nervous systems in vitro with HPLC

High performance liquid chromatography (HPLC) is widely used to determine neurotransmitter concentrations in the central nervous system (CNS). Finding the optimal methods to sample from CNS tissue poses a challenge for neuroscientists. Here, we describe a method that allows assay of neurotransmitters (or other chemicals) in small regions (down to 180mum in diameter) in in vitro preparations concurrently with electrophysiological recordings. The efficiency for measuring small amounts of chemicals is enhanced by a sample collecting pipette with filter paper at the tip that makes close contact with the target region in CNS tissue. With a wire plunger in the calibrated pipette controlled by a microsyringe pump, there is virtually no dead volume. Samples in a volume of 10muL (taken, e.g., at 2muL/min over 5min) can be injected into a HPLC machine with microbore columns. We demonstrate the effectiveness of this method by measuring acetylcholine (ACh) in the ventral horn and its surrounding areas of the spinal cord in en bloc brainstem-spinal cord preparations. In control conditions, endogenous ACh levels in these regions were detectable. Application of neostigmine (an inhibitor of acetylcholinesterases (AChEs)) increased ACh concentrations, and at the same time, induced tonic/seizure-like activity in efferent motor output recorded from cervical ventral nerve roots. Higher ACh concentrations in the ventral horn were differentiated from nearby regions: the lateral and midline aspects of the ventral spinal cord. In addition, ACh in the preBötzinger Complex (preBötC) and the hypoglossal nucleus in medullary slice preparations can also be measured. Our results indicate that the method proposed in this study can be used to measure neurotransmitters in small and localized CNS regions. Correlation between changes in neurotransmitters in target regions and the neuronal activities can be revealed in vitro. Our data also suggest that there is endogenous ACh release in spinal ventral motor columns at fourth cervical (C4) level that regulates the respiratory-related motor activity.

Multiperson Use of Syringes Among Injection Drug Users in a Needle Exchange Program

Syringe-sharing behaviors among injection drug users (IDUs) are typically based on self-reports and subject to socially desirable responding. We used 3 short tandem repeat (STR) genetic biomarkers to detect sharing in 2,512 syringes exchanged by 315 IDUs in the Baltimore needle exchange program (NEP; 738 person-visits). Demographic characteristics as well as direct and indirect needle-sharing behaviors corresponding to the closest AIDS Link to Intravenous Experience (ALIVE) study visits were examined for association with multiperson use (MPU) of syringes. Overall, 56% of the syringes exchanged at the Baltimore NEP had evidence of MPU. Less MPU of syringes (48% vs. 71%; P < 0.0001) was seen with more rapid syringe turnaround (<3 days). IDUs always exchanging their own syringes ("primary" syringes) were less likely to return syringes with evidence of MPU (52%) than those who exchanged syringes for others ("secondary" syringes; 64%; P = 0.0001) and those exchanging primary and secondary syringes (58%; P = 0.004). In a multivariate analysis restricted to primary exchangers, MPU of syringes was associated with sharing cotton (adjusted odds ratio [AOR] = 2.06, 95% confidence interval [CI]: 1.30 to 3.28), lending syringes (AOR = 1.70, 95% CI: 1.24 to 2.34), and injecting less than daily (AOR = 0.64, 95% CI: 0.43 to 0.95). These findings support additional public health interventions such as expanded syringe access to prevent HIV and other blood-borne infections. Testing of STRs represents a promising approach to examining and accessing complex behavioral data, including syringe sharing.

Dual-Syringe Reactive Electrospinning of Cross-Linked Hyaluronic Acid Hydrogel Nanofibers for Tissue Engineering Applications

A facile fabrication of a cross-linked hyaluronic acid (HA) hydrogel nanofibers by a reactive electrospinning method is described. A thiolated HA derivative, 3,3'-dithiobis(propanoic dihydrazide)-modified HA (HA-DTPH), and poly(ethylene glycol) diacrylate (PEGDA) are selected as the cross-linking system. The cross-linking reaction occurs simultaneously during the electrospinning process using a dual-syringe mixing technique. Poly(ethylene oxide) (PEO) is added into the spinning solution as a viscosity modifier to facilitate the fiber formation and is selectively removed with water after the electrospinning process. The nanofibrous structure of the electrospun HA scaffold is well preserved after hydration with an average fiber diameter of 110 nm. A cell morphology study on fibronectin (FN)-adsorbed HA nanofibrous scaffolds shows that the NIH 3T3 fibroblasts migrate into the scaffold through the nanofibrous network, and demonstrate an elaborate three-dimensional dendritic morphology within the scaffold, which reflects the dimensions of the electrospun HA nanofibers. These results suggest the application of electrospun HA nanofibrous scaffolds as a potential material for wound healing and tissue regeneration. [image: see text] Laser scanning confocal microscopy demonstrates that the NIH3T3 fibroblast develops an extended 3D dendritic morphology within the fibronectin-adsorbed electrospun HA nanofibrous scaffold.

Accidental needle sticks, the Occupational Safety and Health Administration, and the fallacy of public policy

BACKGROUND

Current Occupational Safety and Health Administration (OSHA) guidelines mandate the use of safety needles when allergy injections are given. Safety needles for intradermal testing remain optional. Whether safety needles reduce the number of accidental needle sticks (ANSs) in the outpatient setting has yet to be proven.

OBJECTIVE

To determine the rate of ANSs with new (safety) needles vs old needles used in allergy immunotherapy and intradermal testing.

METHODS

Allergy practices from 22 states were surveyed by e-mail.

RESULTS

Seventy practices (28%) responded to the survey. Twice as many ANSs occurred in practices giving immunotherapy when using new needles vs old needles (P < .01). The rate of ANSs was roughly the same for intradermal testing with new needles vs old needles.

CONCLUSIONS

These findings further question whether OSHA's guidelines for safety needle use in outpatient practice need revision and if allergy practices might be excluded from the requirement to use safety needles.

Use of a large bore syringe creates significantly fewer high intensity transient signals (HITS) into a cardiopulmonary bypass system than a small bore syringe

INTRODUCTION

High intensity transient signals (HITS) have been reported to occur following perfusionist intervention during cardiac surgery. This study investigates the relationship of the syringe bore, injection rate, and HITS created.

METHODS

Syringes (10 mL) with a male luer-lock connection (Large Bore) and Abboject 'jet syringes' with a 20 GA needle and male luer-lock connector (Small Bore) were filled with 10 mL of 0.9 N saline. A perfusionist was randomly assigned a set of four similar syringes followed by the other syringe bore. Each of the four syringes was injected into an in vitro saline-primed cardiopulmonary bypass (CPB) system over 5, 10, 15, or 20 sec. Sixteen randomizations of small and large bore syringes were completed at the four injection times (128 injections). HITS in the CPB arterial line were detected with transcranial Doppler (TCD) probes, were recorded for the 2 min following the injection, and were counted independently off-line by two reviewers.

RESULTS

The use of a large bore syringe compared to a small bore syringe created significantly fewer HITS (29 +/- 6 versus 145 +/- 17 [mean +/- SEM], p<0.001) introduced into the CPB arterial line. Injection over a longer time produced significantly fewer HITS than shorter injection times (p<0.001).

CONCLUSION

Significantly fewer HITS are introduced into the CPB system by using standard syringes and slower injection time.

[New generation of disposable syringes]

The goal of this work was to consider the problem of disposable syringe supply to treatment-and-prophylaxis institutions (first of all, primary medical care institutions). It is emphasized that the construction of disposable syringes should make it impossible to use them a second time. The historical background of the problem is considered. Construction of disposable syringes of new generation is described, and the problems of their manufacture are discussed.

Safer injections following a new national medicine policy in the public sector, Burkina Faso 1995-2000

Background

The common failure of health systems to ensure adequate and sufficient supplies of injection devices may have a negative impact on injection safety. We conducted an assessment in April 2001 to determine to which extent an increase in safe injection practices between 1995 and 2000 was related to the increased access to injection devices because of a new essential medicine policy in Burkina Faso.

Methods

We reviewed outcomes of the new medicine policy implemented in1995. In April 2001, a retrospective programme review assessed the situation between 1995 and 2000. We visited 52 health care facilities where injections had been observed during a 2000 injection safety assessment and their adjacent operational public pharmaceutical depots. Data collection included structured observations of available injection devices and an estimation of the proportion of prescriptions including at least one injection. We interviewed wholesaler managers at national and regional levels on supply of injection devices to public health facilities.

Results

Fifty of 52 (96%) health care facilities were equipped with a pharmaceutical depot selling syringes and needles, 37 (74%) of which had been established between 1995 and 2000. Of 50 pharmaceutical depots, 96% had single-use 5 ml syringes available. At all facilities, patients were buying syringes and needles out of the depot for their injections prescribed at the dispensary. While injection devices were available in greater quantities, the proportion of prescriptions including at least one injection remained stable between 1995 (26.5 %) and 2000 (23.8 %).

Conclusion

The implementation of pharmaceutical depots next to public health care facilities increased geographical access to essential medicines and basic supplies, among which syringes and needles, contributing substantially to safer injection practices in the absence of increased use of therapeutic injections.

Injection risk behaviors among clients of syringe exchange programs with different syringe dispensation policies

While there have been numerous papers published in the medical, social, and epidemiologic literature about the effectiveness of syringe exchange programs (SEPs), few papers identify operational characteristics of the SEPs they study or assess which of those characteristics are associated with optimal HIV risk reduction among clients. The objective of this study was to examine whether different syringe dispensation policies were associated with client-level injection-related HIV risk. Injection drug users (IDUs) were recruited at 23 SEPs in California in 2001 (n = 531). SEPs were classified by their executive directors as to whether they provided a strict one-for-one syringe exchange, gave a few extra syringes above the one-for-one exchange, or distributed the amount of syringes based upon need as opposed to how many syringes were turned in by the clients. Injection-related risk was compared by SEP program type. In multivariate logistic regression analysis, clients of distribution-based programs had lower odds of reusing syringes (adjusted odds ratio = 0.43; 95% CI = 0.27, 0.71) when adjusting for confounding variables. There were no statistical differences with regards to distributive or receptive syringe sharing by dispensation policy. It is concluded that SEPs that base syringe dispensation policy upon need may facilitate reductions in reuse of syringes.

AAV2-mediated gene delivery to monkey putamen: evaluation of an infusion device and delivery parameters

In this study, a modified infusion procedure and a novel infusion device designed for use in humans (Clinical Device B) were evaluated for delivery of recombinant adeno-associated virus (AAV2) to brain. The device is composed of 1.2 m of fused silica inserted through a 24.6-cm surgical steel cannula designed to fit a standard Leksell clinical stereotaxic frame and micro-infusion syringe pump. AAV2 encoding the human aromatic l-amino acid decarboxylase gene (AAV-hAADC-2) was infused into the putamen of 4 normal rhesus monkeys as a supportive study for a clinical trial in Parkinson's disease (PD) patients. Two infusion protocols were tested: a ramped procedure (slow stepwise increases in rate from 0.2 muL/min to 1 muL/min), thought to be essential for convection-enhanced delivery (CED), and a non-ramped infusion at a constant rate of 1 muL/min. The primary endpoints were safety evaluation of the infusion procedures and assessment of transgene expression at 5.5 weeks post-infusion. Clinical observations after vector infusions revealed no behavioral abnormalities during the study period. No differences in gross pathology with either the ramped or non-ramped infusion procedure were observed. Histopathology of the putamen was comparable with both procedures, and revealed only minimal localized inflammatory tissue reaction along the needle track in response to cannula placement and vector infusion. AADC immunohistochemistry demonstrated that vector was distributed throughout the putamen, with no significant difference in volume of immunostaining with either infusion procedure. Serum antibody levels against AAV2 vector exhibited a minor increase after infusion. These results validate the clinical utility of this new infusion device and non-ramped infusion conditions for intraputamenal gene therapy, and have the potential to impact a number of human diseases in which delivery of therapeutics to brain is indicated.

A novel method for subarachnoid drug delivery in the medullary region of rats

This study describes a novel method for direct subarachnoid drug delivery to the medullary dorsal horn region of rats, without introducing a catheter. The reliability of the method was demonstrated by a pharmacological validation; that is, morphine administration to the medullary region blocked the nociceptive response to formalin injected in the temporomandibular joint (TMJ) region, an effect that was prevented by co-administration of naloxone. The method proposed offers many advantages over the existing methods for medullary drug delivery with catheter implantation. It is easy to be employed, it does not induce any sign of motor impairment, and it does not require the neck surgery performed to implant a catheter in the medullary dorsal horn region. Therefore, it is a useful method for subarachnoid drug delivery in behavioral trigeminal pain studies, particularly when nociceptive behavioral measures that require normal neck muscle activity to occur, such as head withdraw or head flinch, are evaluated.

Adequacy of the epinephrine autoinjector needle length in delivering epinephrine to the intramuscular tissues

BACKGROUND

Epinephrine injected by an autoinjector in the anterolateral aspect of the thigh is the standard of care in the emergency self-treatment of anaphylaxis. In the United States, the autoinjector EpiPen is widely used for the self-treatment of anaphylaxis.

OBJECTIVE

To investigate whether EpiPen autoinjector, with a needle length of 1.43 cm, is sufficient for intramuscular delivery of epinephrine in men and women.

METHODS

The distance from skin to muscle in the anterolateral aspect of the thigh was measured in 50 men and 50 women who had undergone computed tomography of the thighs for other medical reasons. For each individual, body mass index (BMI; a measure of weight in kilograms divided by the square of height in meters) was also calculated, and the individuals were classified as underweight (BMI, < 18.5), normal (BMI, 18.5-24.9), overweight (BMI, 25.0-29.9), and obese (BMI, > or = 30.0) using standard definition.

RESULTS

In the study participants the mean +/- SD distance from skin to muscle was 0.66 +/- 0.47 cm for men and 1.48 +/- 0.72 cm for women (P < .001). One man (obese at a BMI of 42.2) and 21 women (11 obese with a mean BMI of 35.2, 6 overweight with a mean BMI of 30.1, and 4 normal with a mean BMI of 24.5) had a greater distance from skin to muscle than the EpiPen needle length of 1.43 cm.

CONCLUSION

The distance from skin to muscle for the anterolateral aspect of the thigh is higher in women compared with men. This difference suggests that EpiPen may not deliver epinephrine to the intramuscular tissue in many women.