Improved L-Asparaginase Properties and Reusability by Immobilization onto Functionalized Carbon Xerogels

Enzyme immobilization can offer a range of significant advantages, including reusability, and increased selectivity, stability, and activity. In this work, a central composite design (CCD) of experiments and response surface methodology (RSM) were used to study, for the first time, the L-asparaginase (ASNase) immobilization onto functionalized carbon xerogels (CXs). The best results were achieved using CXs obtained by hydrothermal oxidation with nitric acid and subsequent heat treatment in a nitrogen flow at 600 °C (CX-OX-600). Under the optimal conditions (81 min of contact time, pH 6.2 and 0.36 g/L of ASNase), an immobilization yield (IY) of 100 % and relative recovered activity (RRA) of 103 % were achieved. The kinetic parameters obtained also indicate a 1.25-fold increase in the affinity of ASNase towards the substrate after immobilization. Moreover, the immobilized enzyme retained 97 % of its initial activity after 6 consecutive reaction cycles. All these outcomes confirm the promising properties of functionalized CXs as support for ASNase, bringing new insights into the development of an efficient and stable immobilization platform for use in the pharmaceutical industry, food industry, and biosensors.

Engineering g-C3N4 with CuAl-layered double hydroxide in 2D/2D heterostructures for visible-light water splitting

CuAl layered double hydroxide (LDH) and polymeric carbon nitride (g-C3N4, GCNN) were assembled to construct a set of novel 2D/2D CuAl-LDH/GCNN heterostructures. These materials were tested towards H2 and O2 generation from water splitting using visible-light irradiation. Compared to pristine materials, the heterostructures displayed strongly enhanced visible-light H2 evolution, dependent on the LDH content, which acts as a cocatalyst, replacing the benchmark Pt. The optimal LDH loading was achieved for 0.2CuAl-LDH/GCNN that exhibited an increased number of active sites and showed a trade-off between charge separation efficiency and light shading, resulting in a 32-fold increase in the amount of evolved H2 compared with GCNN. In addition, the 0.2CuAl-LDH/GCNN heterostructure generated 1.5 times more O2 than GCNN. The higher photocatalytic performance was due to efficient charge carriers' separation at the heterojunction interface via an S-scheme (corroborated by work function, steady-state and time-resolved photoluminescence studies), enhanced utilisation of longer-wavelength photons (>460 nm) and higher surface area available for the catalytic reactions.

Novel photoelectrochemical 3D-system for water disinfection by deposition of modified carbon nitride on vitreous carbon foam

Graphitic carbon nitride (GCN) is an optical semiconductor with excellent photoactivity under visible light irradiation. It has been widely applied for organic micropollutant removal from contaminated water, and less investigated for microorganisms' inactivation. The photocatalytic degradation mechanism using GCN is attributed to a series of reactions with reactive oxygen species and photogenerated holes that can be boosted by modifying its physical-chemical structure. This work reports a successful improvement of the overall photocatalytic and electrocatalytic activities of the pristine material by thermal and chemical modification by a copolymerisation synthesis method. The copolymerisation of dicyandiamide as a precursor with barbituric acid strongly reduced photoluminescence due to the enhanced charge separation thus improving the catalyst efficiency under visible light irradiation. The material with 1.6 wt% of barbituric acid showed the best photocatalytic performance and electrochemical properties. This photocatalyst was selected for immobilisation on a conductive carbon foam, which promotes a higher electrochemical active surface area and enhanced mass transfer. This three-dimensional metal-free electrode was employed for the photoelectrochemical inactivation of two different microorganisms, Escherichia coli, and Enterococcus faecalis, obtaining removals below the detection limit after 30 min in simulated faecal-contaminated waters. This photoelectrochemical reactor was also applied to treat polluted river and urban waste waters, and the faecal contamination indicators were vastly reduced to values below the detection limit in 60 min in both cases, showing the wide applicability of this innovative photoelectrode for different types of polluted aqueous matrices.

Photocatalytic Hydrogen Production using Porous 3D Graphene-Based Aerogels Supporting Pt/TiO2 Nanoparticles

Composites involving reduced graphene oxide (rGO) aerogels supporting Pt/TiO2 nanoparticles were fabricated using a one-pot supercritical CO2 gelling and drying method, followed by mild reduction under a N2 atmosphere. Electron microscopy images and N2 adsorption/desorption isotherms indicate the formation of 3D monolithic aerogels with a meso/macroporous morphology. A comprehensive evaluation of the synthesized photocatalyst was carried out with a focus on the target application: the photocatalytic production of H2 from methanol in aqueous media. The reaction conditions (water/methanol ratio, catalyst concentration), together with the aerogel composition (Pt/TiO2/rGO ratio) and architecture (size of the aerogel pieces), were the factors that varied in optimizing the process. These experimental parameters influenced the diffusion of the reactants/products inside the aerogel, the permeability of the porous structure, and the light-harvesting properties, all determined in this study towards maximizing H2 production. Using methanol as the sacrificial agent, the measured H2 production rate for the optimized system (18,800 µmolH2h-1gNPs-1) was remarkably higher than the values found in the literature for similar Pt/TiO2/rGO catalysts and reaction media (2000-10,000 µmolH2h-1gNPs-1).

Recent Developments and Challenges in the Application of Fungal Laccase for the Biodegradation of Textile Dye Pollutants

Abstract:

According to the European Environment Agency, the textile industry is responsible for 20% of global water pollution due to dyeing and finishing products, thus facing severe environmental challenges. It is essential to design more biocompatible and sustainable treatment processes capable of removing dyes from industrial wastewater to fight this environmental hazard. Chemical industries must change traditional chemical-based concepts to more environmentally friendly and greener processes to remove pollutants, including dyes. Enzymatic bioremediation is a smart tool and a promising alternative for environmental pollutant degradation. The use of enzymes in dye decolourization makes the process a green and clean alternative to conventional chemical treatments. Moreover, enzyme-mediated biocatalysis decreases the formation of toxic by-products compared to chemical reactions. The most used enzyme for the decolourization of dyes is laccase. Laccase is a multicopper oxidase found in diverse organisms such as fungi. It promotes the oxidation of phenolic compounds and has a wide range of substrate specificity, making it a promising enzyme for removing different dyes used by the textile industry, including recalcitrant aromatic dyes. The present article gives a comprehensive revision of textile dye decolourization, its types, recent developments in laccase-mediated dye bioremediation technologies, the mechanism of biocatalysis, and their limitations and challenges. Emphasis on the chemical pathways of laccase reaction mechanisms for dye bioremediation processes is also provided. In addition, a brief overview of textile industries and the respective traditional treatment processes for textile wastewater is also presented.

Immobilization and Characterization of L-Asparaginase over Carbon Xerogels

L-asparaginase (ASNase) is an aminohydrolase currently used in the pharmaceutical and food industries. Enzyme immobilization is an exciting option for both applications, allowing for a more straightforward recovery and increased stability. High surface area and customizable porosity make carbon xerogels (CXs) promising materials for ASNase immobilization. This work describes the influence of contact time, pH, and ASNase concentration on the immobilization yield (IY) and relative recovered activity (RRA) using the Central Composite Design methodology. The most promising results were obtained using CX with an average pore size of 4 nm (CX-4), reaching IY and RRA of 100%. At the optimal conditions (contact time 49 min, pH 6.73, and [ASNase] 0.26 mg·mL⁻¹), the ASNase-CXs biocomposite was characterized and evaluated in terms of kinetic properties and operational, thermal, and pH stabilities. The immobilized ASNase onto CX-4 retained 71% of its original activity after six continuous reaction cycles, showed good thermal stability at 37 °C (RRA of 91% after 90 min), and was able to adapt to both acidic and alkaline environments. Finally, the results indicated a 3.9-fold increase in the immobilized ASNase affinity for the substrate, confirming the potential of CXs as a support for ASNase and as a cost-effective tool for subsequent use in the therapeutic and food sectors.

Impact of atomic layer deposited TiO2 on the photocatalytic efficiency of TiO2/w-VA-CNT nanocomposite materials

Titanium oxide (TiO₂) has been widely investigated as a photocatalytic material, and the fact that its performance depends on its crystalline structure motivates further research on the relationship between preparation methods and material properties. In this work, TiO₂ thin films were grown on non-functionalized wave-like patterned vertically aligned carbon nanotubes (w-VA-CNTs) via the atomic layer deposition (ALD) technique. Grazing incidence X-ray diffraction (GIXRD) analysis revealed that the structure of the TiO₂/VA-CNT nanocomposites varied from amorphous to a crystalline phase with increasing deposition temperature, suggesting a “critical deposition temperature” for the anatase crystalline phase formation. On the other hand, scanning transmission electron microscopy (STEM) studies revealed that the non-functionalized carbon nanotubes were conformally and homogeneously coated with TiO₂, forming a nanocomposite while preserving the morphology of the nanotubes. X-ray photoelectron spectroscopy (XPS) provided information about the surface chemistry and stoichiometry of TiO₂. The photodegradation experiments under ultraviolet (UV) light on a model pollutant (Rhodamine B, RhB) revealed that the nanocomposite comprised of anatase crystalline TiO₂ grown at 200 °C (11.2 nm thickness) presented the highest degradation efficiency viz 55% with an illumination time of 240 min. Furthermore, its recyclability was also demonstrated for multiple cycles, showing good recovery and potential for practical applications.

Amorphous or anatase crystalline TiO₂/VA-CNT nanocomposites were grown controlling the synthesis temperature. Photocatalytic degradation of RhB of 55% was achieved after 240 min. The immobilized material remains active after 4 cycles of use.

Superior operational stability of immobilized L-asparaginase over surface-modified carbon nanotubes

L-asparaginase (ASNase, EC 3.5.1.1) is an enzyme that catalyzes the L-asparagine hydrolysis into L-aspartic acid and ammonia, being mainly applied in pharmaceutical and food industries. However, some disadvantages are associated with its free form, such as the ASNase short half-life, which may be overcome by enzyme immobilization. In this work, the immobilization of ASNase by adsorption over pristine and modified multi-walled carbon nanotubes (MWCNTs) was investigated, the latter corresponding to functionalized MWCNTs through a hydrothermal oxidation treatment. Different operating conditions, including pH, contact time and ASNase/MWCNT mass ratio, as well as the operational stability of the immobilized ASNase, were evaluated. For comparison purposes, data regarding the ASNase immobilization with pristine MWCNT was detailed. The characterization of the ASNase-MWCNT bioconjugate was addressed using different techniques, namely Transmission Electron Microscopy (TEM), Thermogravimetric Analysis (TGA) and Raman spectroscopy. Functionalized MWCNTs showed promising results, with an immobilization yield and a relative recovered activity of commercial ASNase above 95% under the optimized adsorption conditions (pH 8, 60 min of contact and 1.5 × 10-3 g mL-1 of ASNase). The ASNase-MWCNT bioconjugate also showed improved enzyme operational stability (6 consecutive reaction cycles without activity loss), paving the way for its use in industrial processes.

Light-driven oxygen evolution from water oxidation with immobilised TiO2 engineered for high performance

Calcination treatments in the range of 500–900 °C of TiO₂ synthesised by the sol–gel resulted in materials with variable physicochemical (i.e., optical, specific surface area, crystallite size and crystalline phase) and morphological properties. The photocatalytic performance of the prepared materials was evaluated in the oxygen evolution reaction (OER) following UV-LED irradiation of aqueous solutions containing iron ions as sacrificial electron acceptors. The highest activity for water oxidation was obtained with the photocatalyst thermally treated at 700 °C (TiO₂-700). Photocatalysts with larger anatase to rutile ratio of the crystalline phases and higher surface density of oxygen vacancies (defects) displayed the best performance in OER. The oxygen defects at the photocatalyst surface have proven to be responsible for the enhanced photoactivity, acting as important active adsorption sites for water oxidation. Seeking technological application, water oxidation was accomplished by immobilising the photocatalyst with the highest OER rate measured under the established batch conditions (TiO₂-700). Experiments operating under continuous mode revealed a remarkable efficiency for oxygen production, exceeding 12% of the apparent quantum efficiency (AQE) at 384 nm (UV-LED system) compared to the batch operation mode.

Degradation of diclofenac in water under LED irradiation using combined g-C3N4/NH2-MIL-125 photocatalysts

This study reports the photocatalytic degradation of diclofenac by hybrid materials prepared by combination of graphitic carbon nitride (g-C₃N₄) and titanium-metal organic framework (NH₂-MIL-125), in different mass proportions (MOF:C₃N₄ of 25:75, 50:50 and 75:25). The hybrid materials were fully characterized, and their properties compared to those of the individual components, whose presence was confirmed by XRD. The porous structure was the result of the highly microporous character of the MOF and the non-porous one of g-C₃N₄. The band gap values were very close to that of MOF component. Photoluminescence measurements suggested an increase on the recombination rate associated to the presence of g-C₃N₄. Photodegradation tests of diclofenac (10 mg·L^-1) were performed under UV LED irradiation at 384 nm. The hybrid materials showed higher photocatalytic activity than the individual components, suggesting the occurrence of some synergistic effect. The photocatalyst with a MOF:g-C₃N₄ ratio of 50:50 yielded the highest conversion rate, allowing complete disappearance of diclofenac in 2 h. Experiments with scavengers showed that superoxide radicals and holes played a major role in the photocatalytic process photodegradation, being that of hydroxyl radicals less significant. From the identification of by-products species, a degradation pathway was proposed for the degradation of diclofenac under the experimental operating conditions.

Advances on Graphyne-Family Members for Superior Photocatalytic Behavior

Graphyne (GY) and graphdiyne (GDY) have been employed in photocatalysis since 2012, presenting intriguing electronic and optical properties, such as high electron mobility and intrinsic bandgap due to their high π-conjugated structures. Authors are reporting the enhanced photocatalytic efficiency of these carbon allotropes when combined with different metal oxides or other carbon materials. However, the synthesis of graphyne-family members (GFMs) is still very recent, and not much is known about the true potential of these photocatalytic materials. In this review article, the implications of different synthesis routes on the structural features and photocatalytic properties of these materials are elucidated. The application of GFMs in the nicotinamide adenine dinucleotide (NADH) regeneration, hydrogen and oxygen evolution, and carbon dioxide reduction is discussed, as well as in the degradation of pollutants and bacteria inactivation in water and wastewater treatment.

Graphitic carbon nitride photocatalysis: the hydroperoxyl radical role revealed by kinetic modelling

The behaviour of graphitic carbon nitride photocatalysis for phenol removal and H2O2 evolution was fully analysed by kinetic modelling, rediscovering the contribution of oxygen, reactive oxygen species, photogenerated holes and intermediate products.

Rhodium single-atom catalysts with enhanced electrocatalytic hydrogen evolution performance

Rhodium (Rh) single-atom catalysts supported on activated carbon (Rh₁/AC) are prepared via a “top-down” chemical reaction-induced dispersion process and show outstanding electrocatalytic performance for the hydrogen evolution reaction.

Recent Strategies and Applications for l-Asparaginase Confinement

l-asparaginase (ASNase, EC 3.5.1.1) is an aminohydrolase enzyme with important uses in the therapeutic/pharmaceutical and food industries. Its main applications are as an anticancer drug, mostly for acute lymphoblastic leukaemia (ALL) treatment, and in acrylamide reduction when starch-rich foods are cooked at temperatures above 100 °C. Its use as a biosensor for asparagine in both industries has also been reported. However, there are certain challenges associated with ASNase applications. Depending on the ASNase source, the major challenges of its pharmaceutical application are the hypersensitivity reactions that it causes in ALL patients and its short half-life and fast plasma clearance in the blood system by native proteases. In addition, ASNase is generally unstable and it is a thermolabile enzyme, which also hinders its application in the food sector. These drawbacks have been overcome by the ASNase confinement in different (nano)materials through distinct techniques, such as physical adsorption, covalent attachment and entrapment. Overall, this review describes the most recent strategies reported for ASNase confinement in numerous (nano)materials, highlighting its improved properties, especially specificity, half-life enhancement and thermal and operational stability improvement, allowing its reuse, increased proteolysis resistance and immunogenicity elimination. The most recent applications of confined ASNase in nanomaterials are reviewed for the first time, simultaneously providing prospects in the described fields of application.

Adsorption of Sudan-IV contained in oily wastewater on lipophilic activated carbons: kinetic and isotherm modelling

Up to nine kinetic and fourteen isotherm adsorption models are employed to model the adsorption of Sudan IV, a lipophilic model pollutant present in a biphasic mixture of cyclohexane-water system to simulate oily wastewater. Six different modified activated carbons were used as adsorbents. The highest amount adsorbed of Sudan IV was found in the material prepared by successive treatments of the parent commercial activated carbon Norit ROX 0.8 with nitric acid and urea, followed by thermal treatment at 800 °C under continuous flow of nitrogen. Kinetic and isotherm adsorption models can be employed to simulate the process, since the effect of the presence of water in the adsorption of Sudan IV from the cyclohexane phase was found to be negligible, owing to the high lipophilic character of both adsorbent and adsorbate. All kinetic and isotherm coefficients, coupling with statistical parameters (r², adjusted r² and sum of squared errors), are determined by non-linear regression fitting and compared to literature data. The model of Avrami is found to be the most appropriate model to represent the adsorption of the pollutant in any of the six modified carbons tested, the highest value of the kinetic constant being 0.055 min^-1. The isotherm adsorption is well-modelled by using the general isotherm equation of Tóth and the multilayer Jovanović expression for the adsorption of Sudan-IV on that material, resulting in a high monolayer uptake capacity (q_m = 193.6 mg g^-1).

Degradation of methylparaben by sonocatalysis using a Co-Fe magnetic carbon xerogel

The degradation of methylparaben (MP) through 20 kHz ultrasound coupled with a bimetallic Co-Fe carbon xerogel (CX/CoFe) was investigated in this work. Experiments were performed at actual power densities of 25 and 52 W/L, catalyst loadings of 12.5 and 25 mg/L, MP concentrations between 1 and 4.2 mg/L and initial pH values between 3 and 10 in ultrapure water (UPW). Matrix effects were studied in bottled water (BW) and secondary treated wastewater (WW), as well as in UPW spiked with bicarbonate, chloride or humic acid. The pseudo-first order kinetics of MP degradation increase with power and catalyst loading and decrease with MP concentration and matrix complexity; moreover, the reaction is also favored at near-neutral conditions and in the presence of dissolved oxygen. The contribution of the catalyst is synergistic to the sonochemical degradation of MP and the extent of synergy is quantified to be >45%. This effect was ascribed to the ability of CX/CoFe to catalyze the dissociation of hydrogen peroxide, formed through water sonolysis, to hydroxyl radicals. Experiments in UPW spiked with an excess of tert-butanol (radical scavenger), sodium dodecyl sulfate or sodium acetate (surfactants) led to substantially decreased rates (i.e. by about 8 times), thus implying that the liquid bulk and the gas-liquid interface are major reaction sites. The stability of CX/CoFe was shown by performing reusability cycles employing magnetic separation of the catalyst after the treatment stage. It was found that the CX/CoFe catalyst can be reused in up to four successive cycles without noteworthy variation of the overall performance of the sonocatalytic process.

Aqueous solution photocatalytic synthesis of p-anisaldehyde by using graphite-like carbon nitride photocatalysts obtained via the hard-templating route

Graphite-like carbon nitride (GCN)-based materials were developed via the hard-templating route, using dicyandiamide as the GCN precursor and silica templates. That resulted in urchin-like GCN (GCN-UL), 3D ordered macroporous GCN (GCN-OM) and mesoporous GCN (GCN-MP). The introduction of silica templates during GCN synthesis produced physical defects on its surface, as confirmed by SEM analysis, increasing their specific surface area. A high amount of nitrogen vacancies is present in modified catalysts (revealed by XPS measurements), which can be related to an increase in the reactive sites available to catalyse redox reactions. The textural and morphological modifications induced in GCN an enhanced light absorption capacity and reduced electron/hole recombination rate, contributing to its improved photocatalytic performance. In the photocatalytic conversion of p-anisyl alcohol to p-anisaldehyde in deoxygenated aqueous solutions under UV-LED irradiation, the GCN-UL was the best photocatalyst reaching 60% yield at 64% conversion for p-anisaldehyde production after 240 min of reaction. Under oxygenated conditions (air), the process efficiency was increased to 79% yield at 92% conversion only after 90 min reaction. The GCN-based photocatalyst kept its performance when using visible-LED radiation under air atmosphere. Trapping of photogenerated holes and radicals by selective scavengers showed that under deoxygenated conditions, holes played the primary role in the p-anisaldehyde synthesis. Under oxygenated conditions, the process is governed by the effect of reactive oxygen species, namely superoxide radicals, with a significant contribution from holes.

Efficient removal of parabens from real water matrices by a metal-free carbon nitride photocatalyst

Metal-free graphite-like carbon nitride (GCN-500) was obtained by thermal post-treatment of bulk polymeric carbon nitride at 500 °C. The catalyst was thoroughly characterized by morphological, optical and textural analysis techniques. The efficiency of GCN-500 was evaluated under visible (λ_exc = 417 nm) LED excitation for the photocatalytic degradation of methyl-, ethyl- and propyl-paraben in different water matrices either isolated or in a mixture of the three compounds. The GCN-500 proved to be more efficient than the benchmark TiO₂ P25, with complete conversion of the individual parabens within 20 min of irradiation, contrasting with 120 min needed for total degradation using TiO₂. Experiments in the presence of selected scavengers confirmed the high importance of superoxide radicals in the photocatalytic oxidation of parabens using GCN-500. The effect of the nature of the aqueous matrix in the kinetics of the photocatalytic process was assessed using ultrapure, tap and river waters spiked with a mixture of the three parabens. Although still very efficient, the complexity of the real water samples turned the degradation process slower due to the presence of other components such as ions and dissolved organic matter. GCN-500 proved to be stable in a continuous-flow system using GCN-500 coated glass rings (GCN-500-GR) to remove MP, EP and PP from real water matrices.

Hummers' and Brodie's graphene oxides as photocatalysts for phenol degradation

Undoped metal-free graphene oxide (GO) materials prepared by either a modified Hummers' (GO-H) or a Brodie's (GO-B) method were tested as photocatalysts in aqueous solution for the oxidative conversion of phenol. In the dark, the adsorptive capacity of GO-B towards phenol (~35%) was higher than that of GO-H (~15%). Upon near-UV/Vis irradiation, GO-H was able to remove 21% of phenol after 180 min, mostly through adsorption. On the other hand, by using less energetic visible irradiation, GO-B removed as much as 95% in just 90 min. By thorough characterization of the prepared materials (SEM, HRTEM, TGA, TPD, Raman, XRD, XPS and photoluminescence) the observed performances could be explained in terms of their different surface chemistries. The GO-B presents the lower concentration of oxygen functional groups (in particular carbonyl groups as revealed by XPS) and it has a considerably higher photocatalytic activity compared to GO-H. Photoluminescence (PL) of liquid dispersions and XRD analysis of powders showed lower PL intensity and smaller interlayer distance for GO-B relative to GO-H, respectively: this suggests lower electron-hole recombination and enhanced electron transfer in GO-B, in support of its boosted photocatalytic activity. Reusability tests showed no efficiency loss after a second usage cycle and over three runs under visible irradiation, which was in line with the similarity of the XPS spectra of the fresh and used GO-B materials. Moreover, scavenging studies revealed that holes and hydroxyl radicals were the main reactive species in play during the photocatalytic process. The obtained results, establish for the first time, that GO prepared by Brodie's method is an active and stable undoped metal-free photocatalyst for phenol degradation in aqueous solutions, opening new paths for the application of more sustainable and metal-free materials for water treatment solutions.

Treatment of biodigested coffee processing wastewater using Fenton's oxidation and coagulation/flocculation

Biodigested coffee processing wastewater (CPW) presents a high organic load and does not meet the limits imposed by legislation (namely in Brazil) for discharge into water bodies. Anaerobic digestion generally cannot provide a satisfactory organic matter reduction in CPW as a significant fraction of recalcitrant compounds still persists in the treated effluent. So, this study aims to find alternative ways to remove refractory organic compounds from this wastewater in order to improve the biodegradability and reduce the toxicity, which will allow its recirculation back into the anaerobic digester. Three treatment approaches (Fenton's oxidation - Approach 1, Coagulation/flocculation (C/F) - Approach 2, and the combination of C/F with Fenton's process - Approach 3) were selected to be applied to the biodigested CPW in order to achieve that objective. The application of the Fenton process under the optimal operating conditions (initial pH = 5.0; T = 55 °C, [Fe³⁺] = 1.8 g L^-1 and [H₂O₂] = 9.0 g L^-1) increased the biodegradability (the BOD₅:COD ratio raised from 0.34 ± 0.02 in biodigested CPW to 0.44 ± 0.01 after treatment) and eliminated the toxicity (0.0% of Vibrio fischeri inhibition) along with moderate removals of organic matter (51.3%, 55.7% and 39.7% for total organic carbon - TOC, chemical oxygen demand - COD and biochemical oxygen demand - BOD₅, respectively). The implementation of a coagulation/flocculation process upstream from Fenton's oxidation, under the best operating conditions (pH 10-11 and [Fe³⁺] = 250 mg L^-1), also allowed to slightly increase the biodegradability (from 0.34 to 0.47) and reduce the toxicity, whereas providing a higher removal of organic matter (TOC = 76.2%, COD = 76.5 and BOD₅ = 66.3% for both processes together). Approach 1 and Approach 3 showed to be the best ones, implying similar operating costs (∼74 R$ m^-3/∼17 € m^-3) and constitute an attractive option for managing biodigested CPW.

Development and characterization of a novel l-asparaginase/MWCNT nanobioconjugate

The enzyme l-asparaginase (ASNase) presents effective antineoplastic properties used for acute lymphoblastic leukemia treatment besides their potential use in the food sector to decrease the acrylamide formation. Considering their applications, the improvement of this enzyme's properties by efficient immobilization techniques is in high demand. Carbon nanotubes are promising enzyme immobilization supports, since these materials have increased surface area and effective capacity for enzyme loading. Accordingly, in this study, multi-walled carbon nanotubes (MWCNTs) were explored as novel supports for ASNase immobilization by a simple adsorption method. The effect of pH and contact time of immobilization, as well as the ASNase to nanoparticles mass ratio, were optimized according to the enzyme immobilization yield and relative recovered activity. The enzyme–MWCNTs bioconjugation was confirmed by thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), Raman and transmission electron microscopy (TEM) studies. MWCNTs have a high ASNase loading capacity, with a maximum immobilization yield of 90%. The adsorbed ASNase retains 90% of the initial enzyme activity at the optimized conditions (pH 8.0, 60 min, and 1.5 × 10⁻³ g mL⁻¹ of ASNase). According to these results, ASNase immobilized onto MWCNTs can find improved applications in several areas, namely biosensors, medicine and food industry.

l-Asparaginase immobilization by adsorption over MWCNTs for potential application in pharmaceutical and food industries.

Catalytic and Photocatalytic Nitrate Reduction Over Pd-Cu Loaded Over Hybrid Materials of Multi-Walled Carbon Nanotubes and TiO2

TiO2 and carbon nanotube-TiO2 hybrid materials synthesized by sol-gel and loaded with 1%Pd-1%Cu (%wt.) were tested in the catalytic and photocatalytic reduction of nitrate in water in the presence of CO2 (buffer) and H2 (reducing agent). Characterization of the catalysts was performed by UV-Vis and fluorescence spectroscopy, X-ray diffraction, temperature programed reduction, N2 adsorption, and electron microscopy. The presence of light produced a positive effect in the kinetics of nitrate removal. Higher selectivity toward nitrogen formation was observed under dark condition, while the photo-activated reactions showed higher selectivity for the production of ammonium. The hybrid catalyst containing 20 %wt. of carbon nanotubes shows the best compromise between activity and selectivity. A mechanism for the photocatalytic abatement of nitrate in water in the presence of the hybrid materials was proposed, based in the action of carbon nanotubes as light harvesters, dispersing media for TiO2 particles and as charge carrier facilitators.

Degradation of propyl paraben by activated persulfate using iron-containing magnetic carbon xerogels: investigation of water matrix and process synergy effects

An advanced oxidation process comprising an iron-containing magnetic carbon xerogel (CX/Fe) and persulfate was tested for the degradation of propyl paraben (PP), a contaminant of emerging concern, in various water matrices. Moreover, the effect of 20 kHz ultrasound or light irradiation on process performance was evaluated. The pseudo-first order degradation rate of PP was found to increase with increasing SPS concentration (25-500 mg/L) and decreasing PP concentration (1690-420 μg/L) and solution pH (9-3). Furthermore, the effect of water matrix on kinetics was detrimental depending on the complexity (i.e., wastewater, river water, bottled water) and the concentration of matrix constituents (i.e., humic acid, chloride, bicarbonate). The simultaneous use of CX/Fe and ultrasound as persulfate activators resulted in a synergistic effect, with the level of synergy (between 35 and 50%) depending on the water matrix. Conversely, coupling CX/Fe with simulated solar or UVA irradiation resulted in a cumulative effect in experiments performed in ultrapure water.

TiO2-based (Fe3O4, SiO2, reduced graphene oxide) magnetically recoverable photocatalysts for imazalil degradation in a synthetic wastewater

Magnetite (Fe₃O₄), a core-shell material (SiO₂@Fe₃O₄), and reduced graphene oxide-Fe₃O₄ (referred as rGO-MN) were used as supports of a specific highly active TiO₂ photocatalyst. Thermal treatments at 200 or 450 °C, different atmospheres (air or N₂), and TiO₂:support weight ratios (1.0, 1.5, or 2.0) were investigated. X-ray diffractograms revealed that magnetite is not oxidized to hematite when the core-shell SiO₂@Fe₃O₄ material-or a N₂ atmosphere (instead of air) in the thermal treatment-was employed to prepare the TiO₂-based catalysts (the magnetic properties being preserved). The materials treated with N₂ were first tested for degradation of imazalil (a well-known fungicide) in deionized water. The best compromise between the photocatalytic activity, magnetic separation, and Fe leached (1.61 mg L^-1, i.e., below the threshold for water reuse in irrigation) was found for the magnetic catalyst prepared with SiO₂@Fe₃O₄, an intermediate TiO₂:support ratio (1.5), and treated at 200 °C under N₂ atmosphere (i.e., SiO₂@Fe₃O₄-EST-1.5-200-N₂). This material was then tested for the treatment of imazalil in a synthetic wastewater, SW (with a chemical composition simulating an effluent resulting from fruit postharvest activity). This SW has a pH of 4.2 and the experiments were carried out at this natural pH₀ and at neutral conditions (keeping pH at 7 along the reaction). The magnetic catalyst was more active than bare TiO₂ for the treatment of imazalil in SW at natural pH. Since Fe leaching was observed (3.53 mg L^-1), added H₂O₂ enhanced both imazalil degradation and mineralization. Conveniently, these catalysts can be readily recovered by using a conventional magnetic field, as demonstrated over three consecutive recycling runs. Graphical abstract % Imazalil conversion using different magnetic catalysts and comparison with bare TiO₂.

β-Cyclodextrin as a Precursor to Holey C-Doped g-C3 N4 Nanosheets for Photocatalytic Hydrogen Generation

A green, template-free and easy-to-implement strategy was developed to access holey g-C₃ N₄ (GCN) nanosheets doped with carbon. The protocol involves heating dicyandiamide with β-cyclodextrin (βCD) prior to polymerization. The local symmetry of the GCN skeleton is broken, yielding CxGCN (x corresponds to the initial amount of βCD used) with pores and a distorted structure. The electronic, emission, optical and textural properties of the best-performing material, C2GCN, were significantly modified as compared to bulk GCN. The spectroscopic and luminescent features of C2GCN show the characteristic π-π* electronic transition of GCN, accompanied by much stronger n-π* electronic transitions owing to the porous and distorted network. These new electronic transitions, along with the presence of additional carbon synergistically contributed to enhanced visible light absorption and restrained recombination of electron-hole pairs. Steady-state and time-resolved photoluminescence showed an effective quench of the fluorescence emission, accompanied by a decrease of fluorescence lifetime of C2GCN (2.20 ns) in comparison with GCN (5.85 ns), owing to the delocalization of electron and holes to new recombination centers. The photocatalytic activity of C2GCN was attributed to efficient charge carrier separation and improved visible-light absorbing ability. As result, C2GCN exhibited ∼5 times higher photocatalytic H₂ generation under visible light than bulk GCN.

Solar treatment (H2O2, TiO2-P25 and GO-TiO2 photocatalysis, photo-Fenton) of organic micropollutants, human pathogen indicators, antibiotic resistant bacteria and related genes in urban wastewater

Solar-driven advanced oxidation processes were studied in a pilot-scale photoreactor, as tertiary treatments of effluents from an urban wastewater treatment plant. Solar-H₂O₂, heterogeneous photocatalysis (with and/or without the addition of H₂O₂ and employing three different photocatalysts) and the photo-Fenton process were investigated. Chemical (sulfamethoxazole, carbamazepine, and diclofenac) and biological contaminants (faecal contamination indicators, their antibiotic resistant counterparts, 16S rRNA and antibiotic resistance genes), as well as the whole bacterial community, were characterized. Heterogeneous photocatalysis using TiO₂-P25 and assisted with H₂O₂ (P25/H₂O₂) was the most efficient process on the degradation of the chemical organic micropollutants, attaining levels below the limits of quantification in less than 4 h of treatment (corresponding to Q_UV < 40 kJ L^-1). This performance was followed by the same process without H₂O₂, using TiO₂-P25 or a composite material based on graphene oxide and TiO₂. Regarding the biological indicators, total faecal coliforms and enterococci and their antibiotic resistant (tetracycline and ciprofloxacin) counterparts were reduced to values close, or beneath, the detection limit (1 CFU 100 mL^-1) for all treatments employing H₂O₂, even upon storage of the treated wastewater for 3-days. Moreover, P25/H₂O₂ and solar-H₂O₂ were the most efficient processes in the reduction of the abundance (gene copy number per volume of wastewater) of the analysed genes. However, this reduction was transient for 16S rRNA, intI1 and sul1 genes, since after 3-days storage of the treated wastewater their abundance increased to values close to pre-treatment levels. Similar behaviour was observed for the genes qnrS (using TiO₂-P25), bla_CTX-M and bla_TEM (using TiO₂-P25 and TiO₂-P25/H₂O₂). Interestingly, higher proportions of sequence reads affiliated to the phylum Proteobacteria (Beta- and Gammaproteobacteria) were found after 3-days storage of treated wastewater than before its treatment. Members of the genera Pseudomonas, Rheinheimera and Methylotenera were among those with overgrowth.

Activation of sodium persulfate by magnetic carbon xerogels (CX/CoFe) for the oxidation of bisphenol A: Process variables effects, matrix effects and reaction pathways

An advanced oxidation process comprising sodium persulfate (SPS) and a novel magnetic carbon xerogel was tested for the degradation of bisphenol A (BPA), a model endocrine-disrupting compound. The catalyst, consisting of interconnected carbon microspheres with embedded iron and cobalt microparticles, was capable of activating persulfate to form sulfate and hydroxyl radicals at ambient conditions. The pseudo-first order degradation rate of BPA in ultrapure water (UPW) was found to increase with (i) increasing catalyst (25-75 mg/L) and SPS (31-250 mg/L) concentrations, (ii) decreasing BPA concentration (285-14,200 μg/L), and (iii) changing pH from alkaline to acidic values (9-3). Besides UPW, tests were conducted in drinking water, treated wastewater, groundwater and surface water; interestingly, the rate in UPW was always lower than in any other matrix containing several organic and inorganic constituents. The effect of natural organic matter (in the form of humic acids) and alcohols was detrimental to BPA degradation owing to the scavenging of radicals. Conversely, chlorides at concentrations greater than 50 mg/L had a positive effect due to the formation and subsequent participation of chlorine-containing radicals. Liquid chromatography time-of-flight mass spectrometry was employed to identify major transformation by-products (TBPs) of BPA degradation in the absence and presence of chlorides; in the latter case, several chlorinated TBPs were detected confirming the role of Cl-related radicals. Based on TBPs, main reaction pathways are proposed.

Photocatalytic ozonation of aniline with TiO2-carbon composite materials

The photocatalytic ozonation of aniline (ANL) aqueous solutions was carried out in the presence of neat titanium dioxide (TiO₂), multi-walled carbon nanotubes (MWCNT) and a composite of TiO₂ and MWCNT. Independent tests for catalytic ozonation and photocatalysis were also carried out in order to explore the potential occurrence of a synergetic effect. Photocatalytic and catalytic ozonation carried out with an ozone dose of 50 g m^-3 converted ANL in 15 min. Photocatalysis using P25, commercial TiO₂, and an 80:20 (w/w) composite of P25 and MWCNT also led to total ANL conversion, but at longer reaction times. Removal of TOC was higher than 70% for all photocatalytic ozonation systems at 1 h of reaction. With the exception of neat MWCNT, photocatalytic ozonation in the presence of the selected samples led to nearly complete mineralization after 3 h of reaction. Photocatalytic ozonation completely removed oxalic acid (OXA) formed during ANL degradation. The concentration of oxamic acid (OMA, other ANL degradation by-product more refractory than OXA) generally increased with time, and in the photocatalytic ozonation with P25 based materials its concentration decreased earlier. The presence of nitrates and ammonium was confirmed during ANL degradation by all tested treatments, with the exception of the cation in TiO₂ catalysed reactions.

Bacteria and fungi inactivation by photocatalysis under UVA irradiation: liquid and gas phase

In the last decade, environmental risks associated with wastewater treatment plants (WWTPs) have become a concern in the scientific community due to the absence of specific legislation governing the occupational exposure limits (OEL) for microorganisms present in indoor air. Thus, it is necessary to develop techniques to effectively inactivate microorganisms present in the air of WWTPs facilities. In the present work, ultraviolet light A radiation was used as inactivation tool. The microbial population was not visibly reduced in the bioaerosol by ultraviolet light A (UVA) photolysis. The UVA photocatalytic process for the inactivation of microorganisms (bacteria and fungi, ATCC strains and isolates from indoor air samples of a WWTP) using titanium dioxide (TiO₂ P25) and zinc oxide (ZnO) was tested in both liquid-phase and airborne conditions. In the slurry conditions at liquid phase, P25 showed a better performance in inactivation. For this reason, gas-phase assays were performed in a tubular photoreactor packed with cellulose acetate monolithic structures coated with P25. The survival rate of microorganisms under study decreased with the catalyst load and the UVA exposure time. Inactivation of fungi was slower than resistant bacteria, followed by Gram-positive bacteria and Gram-negative bacteria. Graphical abstract Inactivation of fungi and bacteria in gas phase by photocatalitic process performed in a tubular photoreactor packed with cellulose acetate monolith structures coated with TiO₂.

Photocatalytic ozonation of urban wastewater and surface water using immobilized TiO2 with LEDs: Micropollutants, antibiotic resistance genes and estrogenic activity

Photocatalytic ozonation was employed for the first time in continuous mode with TiO2-coated glass Raschig rings and light emitting diodes (LEDs) to treat urban wastewater as well as surface water collected from the supply area of a drinking water treatment plant (DWTP). Different levels of contamination and types of contaminants were considered in this work, including chemical priority substances (PSs) and contaminants of emerging concern (CECs), as well as potential human opportunistic antibiotic resistant bacteria and their genes (ARB&ARG). Photocatalytic ozonation was more effective than single ozonation (or even than TiO2 catalytic ozonation) in the degradation of typical reaction by-products (such as oxalic acid), and more effective than photocatalysis to remove the parent micropollutants determined in urban wastewater. In fact, only fluoxetine, clarithromycin, erythromycin and 17-alpha-ethinylestradiol (EE2) were detected after photocatalytic ozonation, by using solid-phase extraction (SPE) pre-concentration and LC-MS/MS analysis. In surface water, this treatment allowed the removal of all determined micropollutants to levels below the limit of detection (0.01-0.20 ng L(-1)). The efficiency of this process was then assessed based on the capacity to remove different groups of cultivable microorganisms and housekeeping (16S rRNA) and antibiotic resistance or related genes (intI1, blaTEM, qnrS, sul1). Photocatalytic ozonation was observed to efficiently remove microorganisms and ARGs. Although after storage total heterotrophic and ARB (to ciprofloxacin, gentamicin, meropenem), fungi, and the genes 16S rRNA and intI1, increased to values close to the pre-treatment levels, the ARGs (blaTEM, qnrS and sul1) were reduced to levels below/close to the quantification limit even after 3-days storage of treated surface water or wastewater. Yeast estrogen screen (YES), thiazolyl blue tetrazolium reduction (MTT) and lactate dehydrogenase (LDH) assays were also performed before and after photocatalytic ozonation to evaluate the potential estrogenic activity, the cellular metabolic activity and the cell viability. Compounds with estrogenic effects and significant differences concerning cell viability were not observed in any case. A slight cytotoxicity was only detected for Caco-2 and hCMEC/D3 cell lines after treatment of the urban wastewater, but not for L929 fibroblasts.

Fast mineralization and detoxification of amoxicillin and diclofenac by photocatalytic ozonation and application to an urban wastewater

The degradation of two organic pollutants (amoxicillin and diclofenac) in 0.1 mM aqueous solutions was studied by using advanced oxidation processes, namely ozonation, photolysis, photolytic ozonation, photocatalysis and photocatalytic ozonation. Diclofenac was degraded quickly under direct photolysis by artificial light (medium-pressure vapor arc, λ(exc) > 300 nm), while amoxicillin remained very stable. In the presence of ozone, regardless of the type of process, complete degradation of both organic pollutants was observed in less than 20 min. Photolysis or ozonation on their own led to modest values of total organic carbon (TOC) removal (<6% or 41%, respectively in 180 min), while for photocatalysis (no ozone present) a significant fraction of nonoxidizable compounds remained in the treated water (∼15% after 180 min). In the case of photolytic ozonation, the kinetics of TOC removal was slow. In contrast, a relatively fast and complete mineralization of amoxicillin and diclofenac (30 and 120 min, respectively) was achieved when applying the photocatalytic ozonation process. The absence of toxicity of the treated waters was confirmed by growth inhibition assays using two different microorganisms, Escherichia coli and Staphylococcus aureus. Photocatalytic ozonation was also applied to an urban wastewater spiked with both amoxicillin and diclofenac. The parent pollutants were easily oxidized, but the TOC removal was only as much as 68%, mainly due to the persistent presence of oxamic acid in the treated sample. The same treatment allowed the effective degradation of a wide group of micropollutants (pesticides, pharmaceuticals, hormones and an industrial compound) detected in non-spiked urban wastewater.

Graphene oxide based ultrafiltration membranes for photocatalytic degradation of organic pollutants in salty water

Flat sheet ultrafiltration (UF) membranes with photocatalytic properties were prepared with lab-made TiO2 and graphene oxide-TiO2 (GOT), and also with a reference TiO2 photocatalyst from Evonik (P25). These membranes were tested in continuous operation mode for the degradation and mineralization of a pharmaceutical compound, diphenhydramine (DP), and an organic dye, methyl orange (MO), under both near-UV/Vis and visible light irradiation. The effect of NaCl was investigated considering simulated brackish water (NaCl 0.5 g L(-1)) and simulated seawater (NaCl 35 g L(-1)). The results indicated that the membranes prepared with the GOT composite (M-GOT) exhibited the highest photocatalytic activity, outperforming those prepared with bare TiO2 (M-TiO2) and P25 (M-P25), both inactive under visible light illumination. The best performance of M-GOT may be due to the lower band-gap energy (2.9 eV) of GOT. In general, the permeate flux was also higher for M-GOT probably due to a combined effect of its highest photocatalytic activity, highest hydrophilicity (contact angles of 11°, 17° and 18° for M-GOT, M-TiO2 and M-P25, respectively) and higher porosity (71%). The presence of NaCl had a detrimental effect on the efficiency of the membranes, since chloride anions can act as hole and hydroxyl radical scavengers, but it did not affect the catalytic stability of these membranes. A hierarchically ordered membrane was also prepared by intercalating a freestanding GO membrane in the structure of the M-GOT membrane (M-GO/GOT). The results showed considerably higher pollutant removal in darkness and good photocatalytic activity under near-UV/Vis and visible light irradiation in continuous mode experiments.

Laccase immobilization over multi-walled carbon nanotubes: Kinetic, thermodynamic and stability studies

The biocatalytic performance of immobilized enzyme systems depends mostly on the intrinsic properties of both biomolecule and support, immobilization technique and immobilization conditions. Multi-walled carbon nanotubes (MWCNTs) possess unique features for enzyme immobilization by adsorption. Enhanced catalytic activity and stability can be achieved by optimization of the immobilization conditions and by investigating the effect of operational parameters. Laccase was immobilized over MWCNTs by adsorption. The hybrid material was characterized by Fourier transformed infrared (FTIR) spectroscopy, scanning and transmission electron microscopy (SEM and TEM, respectively). The effect of different operational conditions (contact time, enzyme concentration and pH) on laccase immobilization was investigated. Optimized conditions were used for thermal stability, kinetic, and storage and operational stability studies. The optimal immobilization conditions for a laccase concentration of 3.75μL/mL were a pH of 9.0 and a contact time of 30min (522 Ulac/gcarrier). A decrease in the thermal stability of laccase was observed after immobilization. Changes in ΔS and ΔH of deactivation were found for the immobilized enzyme. The Michaelis-Menten kinetic constant was higher for laccase/MWCNT system than for free laccase. Immobilized laccase maintained (or even increased) its catalytic performance up to nine cycles of utilization and revealed long-term storage stability.