Stable isotope labeling for detection of ozonation byproducts in effluent organic matter with FT-ICR-MS

Despite effluent organic matter (EfOM) being a major consumer of ozone during wastewater treatment, little is known about ozonation byproducts (OBPs) produced from EfOM. To unambiguously identify OBPs, heavy ozone was used to ozonate EfOM, resulting in ¹⁸O labeled and unlabeled OBPs. Labeled OBPs mostly represent a single ¹⁸O transfer and were classified as either direct or indirect OBPs based on the ¹⁸O/¹⁶O intensity ratios of the isotopologues. Of the 929 labeled OBPs, 84 were unequivocally classified as direct OBPs. The remainder suggest a major contribution by indirect, hydroxyl radical induced formation of OBPs in EfOM. Overall, labelled OBPs possess a low degree of unsaturation and contributed most to OBP peak intensity - marking them as potential end products. A few direct and indirect OBPs with high peak intensity containing ¹⁸O and heteroatoms (N, S) were fragmented with CID FT-ICR-MS/MS and screened for indicative neutral losses carrying heavy oxygen. The neutral loss screening was used to detect the ¹⁸O location on the OBP and indicate the original functional group in EfOM based on known reaction mechanisms. We identified sulfoxide and sulfonic acid functional groups in selected OBPs - implying the presence of reduced sulfur in EfOM molecules - while no evidence for nitrogen containing functional groups reacting with ozone was found.

Degradation of dibutyl phthalate by ozonation in the ultrasonic cavitation-rotational flow interaction coupled-field: performance and mechanism

Dibutyl phthalate (DBP) is present in hydraulic fracturing flowback and produced water. Degradation of DBP in aqueous by means of ozonation in ultrasonic cavitation-rotational flow interaction coupled-field (UC-RF coupled-field) was studied. The effect of ozone dosage, ozone intake flow, operating temperature, initial pH, DBP initial concentration, liquid flow rate, and ultrasonic power on the DBP removal was investigated. Results indicated that the DBP degradation rate was strongly influenced by the liquid flow rate and the ultrasonic power over the range investigated. HCO₃^- and Cl^- revealed an inhibitory effect on the DBP removal. SO₄^2- seemed to have no effect on DBP removal. The ozone utilization efficiencies in the UC-RF coupled-field were 2.77 and 1.13 times higher than those in the conventional microporous aeration (CMA) and rotating-flow microbubble aeration (RFMA), respectively. The DBP degradation rate was diminished in the presence of tert-butyl alcohol. Cavitation bubbles are considered as innumerable microreactors. Degradation of DBP by direct ozonation, hydroxyl radical (·OH) oxidation, high pressure, and high-temperature pyrolysis was demonstrated. Finally, a possible degradation pathway of DBP is obtained on the basis of the main reaction intermediates.

Insight into advanced oxidation processes for the degradation of fluoroquinolone antibiotics: Removal, mechanism, and influencing factors

The enrichment and transport of antibiotics in the environments pose many potential hazards to aquatic animals and humans, which has become one of the public health challenges worldwide. As a widely used class of antibiotics, fluoroquinolones (FQs) generally accumulated in the environments as traditional sewage treatment plants cannot completely remove them. Advanced oxidation processes (AOPs) have been shown to be a promising method for the abatement of antibiotic contamination. In this review, influencing factors and relevant mechanisms of FQs removal by various AOPs were summarized. Compared with other AOPs, photocatalytic ozone may be considered as a cost-effective method for degrading FQs. Finally, the benefits and application restrictions of AOPs were discussed, along with proposed research directions to provide new insights into the control of FQs pollutant via AOPs in practical applications.

Pilot-scale advanced treatment of actual high-salt textile wastewater by a UV/O3 pressurization process: Evaluation of removal kinetics and reverse osmosis desalination process

Advanced oxidation processes (AOPs) such as ozonation and Fenton processes are widely used in the treatment of high-salt wastewater. The UV/O₃ pressurization process was designed and applied at the pilot-scale for treatment of actual high-salt textile wastewater. The UV/O₃ pressurization process achieved the highest decolorization (85 %) and chemical oxygen demand (COD_Cr, 43.2 %) removal efficiency at an O₃ dosage of 200 g·t^-1 and a pressure of 0.2 MPa. Compared to ordinary ozonation, the UV/O₃ pressurization process improved the solubility and gas-liquid mass transfer efficiency of O₃ in wastewater and generated a large number of O₃ microbubbles. Hydroxyl radical (·OH), superoxide radicals (O₂·^-) and single oxygen (¹O₂) all played a significant role on the removal of pollutants in wastewater during the UV/O₃ pressurization process. The reverse osmosis (RO) process was used to evaluate the effect of UV/O₃ pressurization and Fenton pre-oxidation processes on the desalination process as the last process in treating high-salt organic wastewater. The pre-oxidation processes improved the initial RO water flux. Compared with the Fenton process, the UV/O₃ pressurization process had less membrane fouling (thin fouling layer vs thick fouling layer), and final water flux (59.4 LMH) was higher than that of Fenton process (34.9 LHM). The total dissolved solids (TDS), Cl^- and SO₄^2- of the effluent from UV/O₃ pressurization process (37.2, 7.6 and 3.0 mg·L^-1) were better than that of Fenton process (65.7, 13.9 and 7.1 mg·L^-1). Therefore, the UV/O₃ pressurization process without secondary pollution is more suitable for the advanced treatment of high-salt organic wastewater than the Fenton process.

Design, calibration, and testing of a mobile sensor system for air pollution and built environment data collection: The urban scanner platform

This paper describes a mobile air pollution sampling system, the Urban Scanner, which aims at gathering dense spatiotemporal air quality data to support urban air quality and exposure science. Urban Scanner comprises custom vehicle-mounted sensors for air pollution, meteorology, and built environment data collection (low-cost sensors, wind anemometer, 360 deg camera, LIDAR, GPS) as well as a server to store, process, and map all gathered geo-referenced sensory information. Two levels of sensor calibration were implemented, both in a chamber and in the field, against reference instrumentation. Chamber tests and a set of mathematical tools were developed to correct for sensor noise (wavelet denoising), misalignment (linear and nonlinear), and hysteresis removal. Models based on chamber testing were further refined based on field co-location. While field co-location captures natural changes in air pollution and meteorology, chamber tests allow for simulating fast transitions in these variables, like the transitions experienced by a mobile sensor in an urban environment. The best suite of models achieved an R² higher than 0.9 between sensor output and reference station observations and an RMSE of 2.88 ppb for nitrogen dioxide and 4.03 ppb for ozone. A mobile sampling campaign was conducted in the city of Toronto, Canada, to further test Urban Scanner. We observe that the platform adequately captures spatial and temporal variability in urban air pollution, leading to the development of land-use regression models with high explanatory power.

Impacts of meteorological factors and ozone variation on crop yields in China concerning carbon neutrality objectives in 2060

Carbon neutrality objectives affect meteorology and ozone (O₃) concentration in China, both of which would influence crop yields, thus food security. However, the joint impact of these two factors on crop yields in China is not clear. In this study, we investigated future trends in China's maize, rice, soybean, and wheat yields under a carbon-neutral scenario considering both regional emission reduction and global climate change in 2060. By combining a process-based crop model (Agricultural Production Systems sIMulator, APSIM) with O₃ exposure equations, the impacts of regional emission reduction and global climate change were studied. The results suggest that regional emission reduction dominated the increase in yield by reducing the O₃ concentration, whereas global climate change led to yield loss mainly through meteorological factors. The national yield decreases for the four crops ranged from 1.0% to 38.0% owing to meteorological factors, while O₃ reduction resulted in additional yield increases ranging from 2.8% to 7.0%. The combined effect of carbon neutrality, which included both meteorological factors and O₃ concentration, resulted in changes to the yields of maize, rice, soybean, and wheat of +4.3%, -7.3%, -24.0%, and -31.7%, respectively. It seems that crop production loss caused by meteorological factors in 2060 would be mitigated by the O₃ reduction. Given the advantages of declining O₃ concentration, regional emission reduction would likely benefit crop growth. However, global climate change may offset the benefits and threaten food production in China. Therefore, more strict emission reduction policies and global climate change mitigation actions are necessary to ensure food security in China.

Improving the ozone-activated peroxymonosulfate process for removal of trace organic contaminants in real waters through implementation of an optimized sequential ozone dosing strategy

The ozone-activated peroxymonosulfate process (O₃/PMS) has received increasing attention for the removal of trace organic contaminants (e.g. pesticides and pharmaceuticals) from water bodies. However, the ozone dosing strategy has not yet been properly investigated, especially in real water matrices. Typically, one-step dosing is applied in literature. Nevertheless, optimal dosing is an important step for improving the process. This study investigates the effect of sequential ozone dosing on the PMS activation, atrazine (ATZ) removal, residual ozone concentration and radical exposure, and compares the results to those of a one-step ozone dosing approach. Experiments were performed in three water matrices with a different (in)organic content, i.e. secondary effluent, surface water and groundwater. In all matrices, the highest PMS activation was reached when applying three sequential ozone doses (3 × 5 mg O₃/L). This resulted in a 3 times higher ATZ removal efficiency (up to 46 %) in secondary effluent compared to that obtained with a one-step ozone dosing (15 mg O₃/L). In surface water and groundwater, similar ATZ removal (>90 %) was observed among the different ozone dosing strategies. However, the sulfate radical (SO₄^●-) exposure increased after each ozone addition. After three ozone additions of 5 mg/L, SO₄^●- contributed for 9 %, 26 % and 54 % to ATZ removal in respectively secondary effluent, surface water and groundwater. This high SO₄^●- contribution compared to ^●OH contribution is an advantage as the selectivity of SO₄^●- gives rise to less radical scavenging by bulk organic matter and thus increases the (cost-)effectiveness of the O₃/PMS process.

Characteristics, secondary transformation and odor activity evaluation of VOCs emitted from municipal solid waste incineration power plant

Volatile organic compounds (VOCs) emitted from municipal solid waste incineration power plant (MSWIPP) plays a significant role in the formation of O₃ and PM_2.5 and odor pollution. Field test was performed on four MSWIPPs in an area of the North China Plain. Nonmethane hydrocarbons (NMHCs) and 102 VOCs were identified and quantified. Ozone formation potential (OFP), secondary organic aerosol formation potential (SOAFP), and odor activity of the detected VOCs were evaluated. Results showed that the average concentration of NMHCs and VOCs were 1648.6 ± 1290.4 μg/m³ and 635.3 ± 588.8 μg/m³, respectively. Aromatics (62.1%), O-VOCs (16.0%), and halo hydrocarbons (10.0%) were the main VOCs groups in the MSWIPP exhaust gas. VOCs emission factor of MSWIPP was 2.43 × 10³ ± 2.27 × 10³ ng/g-waste. The OFP and SOAFP of MSWIPP were 960.18 ± 2158.17 μg/m³ and 1.57 ± 3.38 μg/m³, respectively. Acrolein as the dominant VOC species was the major odor contributor with a percentage of odor contribution of 65.9%. Benzene and 1,2,4-trimethylbenzene as the dominant VOC species were the main contributors of O₃ formation potentials, in which 1,2,4-trimethylbenzene was also the main contributors of SOA formation potential.

Spectroscopy of Laser-Induced Dielectric Breakdown Plasma in Mixtures of Air with Inert Gases Ar, He, Kr, and Xe

The generation of ozone and nitrogen oxides by laser-induced dielectric breakdown (LIDB) in mixtures of air with noble gases Ar, He, Kr, and Xe is investigated using OES and IR spectroscopy, mass spectrometry, and absorption spectrophotometry. It is shown that the formation of NO and NO₂ noticeably depends on the type of inert gas; the more complex electronic configuration and the lower ionization potential of the inert gas led to increased production of NO and NO₂. The formation of ozone occurs mainly due to the photolytic reaction outside the gas discharge zone. Equilibrium thermodynamic analysis showed that the formation of NO in mixtures of air with inert gases does not depend on the choice of an inert gas, while the equilibrium concentration of the NO+ ion decreases with increasing complexity of the electronic configuration of an inert gas.

Application of partial ozonation on tank truck cleaning concentrate and the influence on biodegradability and ecotoxicity: a pilot-scale study

This study investigates the pilot-scale ozone treatment of reverse osmosis concentrate (ROC), originating from variable tank truck cleaning wastewater. The influence of ozonation on short- and long-term biodegradation potential was examined through respirometry and Zahn-Wellens, respectively. Ecotoxicity was also examined for several concentrate batches and ozonation steps. Chemical oxidation through ozone had a beneficial effect on chemical oxygen demand removal, with a removal efficiency up to 56%. Formation of short-term biochemical oxygen demand (BOD_st) was induced for several, but not all batches, showing the potential of subsequent biological treatment of ozonated ROC. An increase in the inherent biodegradability through Zahn-Wellens was observed for all tested samples after ozonation, rising to a maximum of 68% after 3 hours of ozonation, highlighting the importance of sludge adaptation. Ecotoxicity, tested with Artemia franciscana and the saltwater algae P. tricornutum, showed initial decreases in algae inhibition after short ozonation periods. An increase in algae inhibition was, however, seen after prolonged ozonation for all tested ROC samples, pointing to the formation of ecotoxic by-products. Artemia showed no significant toxicity effects. When applying biological treatment through Zahn-Wellens, a decrease in ecotoxicity was observed for several samples, likely through biological oxidation of the produced degradation products.

A new hybrid models based on the neural network and discrete wavelet transform to identify the CHIMERE model limitation

A greater understanding of ozone damage to the environment and health led to an increased demand for accurate predictions. This study provides two new accurate hybrid models of ozone prediction. The first one (CHIMERE-NARX) is based on a NARX model as a post-processing of the CHIMERE model. In the second (CHIMERE-NARX-DWT), a discrete wavelet transform (DWT) has been added. Our models were built and validated using ozone measurements from the Mediouna station in Casablanca, Morocco, from February 1^st to March 27^th, 2021. The results highlighted the CHIMERE model limitations, such as wind speed overestimation and insufficient emission data. The first hybrid successfully increased the correlation coefficient from 88 to 93% and reduced RMSE from 23.99 μg/m³ to -3.54 μg/m³, overcoming CHIMERE limitations to some extent, especially during nighttime. A second hybrid addressed the first hybrid limitation, such as using ozone as a single input. This hybrid successfully balanced the weight of NARX at night against the day, increasing the correlation coefficient to 98% and decreasing RMSE to -0.02 μg/m³. This study presents a new generation of post-processing based on deterministic model processes, with the possibility of training them with minimum input data, which can be applied to other models using various pollutants.

Analysis of the evolution of ultra-filtered water quality in a drinking water distribution system by particle size distribution: Influence of pre-ozonation

An experimental drinking water distribution system (DWDS) was used to evaluate the evolution of particle size distribution (PSD) and basic quality parameters of ultrafiltered water with or without pre-ozonation. An ultrafiltration (UF) module was set up, associated with a pre-ozonation system (3.7 g O₃ /m³ ). The permeate was circulated in the DWDS (300 m; 0.9 m/s) with 0.4 mg/L of chlorine, and the analysis of the PSD was performed using a β-variable mathematical model. A better control of membrane fouling was obtained with pre-ozonation, and PSD was necessary to observe water quality differences between permeates and in the DWDS. A decrease in particle concentration of 1.8 logarithms was obtained with the application of UF membranes, while a decrease of only 1.2 logarithms was obtained with pre-ozonation. The system without pre-ozonation showed a higher efficiency at removing smaller particles (around 2 μm), with the absence of particles larger than 23 μm during both stages. The PSD revealed a worsening of water quality in the DWDS with an increase of particles smaller than 5 μm during the application of UF membranes, while with pre-ozonation, all particle sizes analyzed increased their concentration. PRACTITIONER POINTS: Pre-ozonation led to a better control of membrane fouling, but a worsening of permeate quality according to particle size distribution. Pre-ozonation does not improve the turbidity, dissolved organic carbon or UV254 removal capacity of ultrafiltration during drinking water treatment. Particles size distribution reveals the deterioration of water quality in a drinking water distribution system better than turbidity or DOC. Ozone prior to ultrafiltration membranes led to a worsening of permeate quality, more significant in the drinking water distribution system.

Efficiency and mechanism of ozonated microbubbles for enhancing the removal of algae and algae-derived organic matter

The effective control of eutrophication caused by algae blooms is still the focus of global attention. The traditional dissolved air floatation process for algae removal has a low adhesion efficiency between bubbles and algal cells and a low removal efficiency of organic pollutants. Aiming to address these defects, this study set up an ozone microbubble-enhanced air flotation experiment to explore the removal trends of algal cells and algal organic matter (AOM) pollution. In contrast to traditional air flotation, this approach targets the removal of various forms of AOM after algal cell damage. The highest removal rates of algal cells, extracellular microcystin (Mc), intracellular Mc-lr and total Mc-lr were 96.6%, 60.1%, 95.2% and 93.7%, respectively. Compared with the traditional process, the absorption rate and utilization rate of ozone were increased by 41.9% and 46.2%, respectively. The removal effect of AOM was also greatly improved, and ozone microbubbles enhanced the removal of aromatic protein-like substances and high-molecular-weight fulvic acid, humic acid and humic substances. The advantageous synergistic effect of ozone and microbubbles on algae removal was analyzed by exploring the enhanced air flotation removal mechanism of ozone microbubbles' enhanced air floatation removal. Good vacuole adhesion and strong oxidation caused by ozone microbubbles jointly guaranteed a good removal rate of AOM. The enhanced air flotation process with ozone microbubbles has high feasibility and a good effect, can effectively remove algal cells and algal pollutants, and has great potential in algal removal and control of water eutrophication.

Tracking long-term population exposure risks to PM2.5 and ozone in urban agglomerations of China 2015-2021

China has experienced severe air pollution in the past decade, especially PM2.5 and emerging ozone pollution recently. In this study, we comprehensively analyzed long-term population exposure risks to PM2.5 and ozone in urban agglomerations of China during 2015-2021 regarding two-stage clean-air actions based on the Ministry of Ecology and the Environment (MEE) air monitoring network. Overall, the ratio of the population living in the regions exceeding the Chinese National Ambient Air Quality Standard (35 μg/m3) decreases by 29.9 % for PM2.5 from 2015 to 2021, driven by high proportions in the Middle Plain (MP, 42.3 %) and Lan-Xi (35.0 %) regions. However, this ratio almost remains unchanged for ozone and even increases by 1.5 % in the MP region. As expected, the improved air quality leads to 234.7 × 103 avoided premature mortality (ΔMort), mainly ascribed to the reduction in PM2.5 concentration. COVID-19 pandemic may influence the annual variation of PM2.5-related ΔMort as it affects the shape of the population exposure curve to become much steeper. Although all eleven urban agglomerations share stroke (43.6 %) and ischaemic heart disease (IHD, 30.1 %) as the two largest contributors to total ΔMort, cause-specific ΔMort is highly regional heterogeneous, in which ozone-related ΔMort is significantly higher (21 %) in the Tibet region than other urban agglomeration. Despite ozone-related ΔMort being one order of magnitude lower than PM2.5-related ΔMort from 2015 to 2021, ozone-related ΔMort is predicted to increase in major urban agglomerations initially along with a continuous decline for PM2.5-related ΔMort from 2020 to 2060, highlighting the importance of ozone control. Coordinated controls of PM2.5 and O3 are warranted for reducing health burdens in China during achieving carbon neutrality.

Historical trend of ozone-depleting substances and hydrofluorocarbon concentrations during 2004-2020 derived from satellite observations and estimates for global emissions

Global concentrations (or mole fractions) and emissions of ozone-depleting substances (ODSs) and their hydrofluorocarbon (HFCs) substitutes that are controlled by the Montreal Protocol and its Amendments and adjustments (MP) are of great interest to both the scientific community and public. Previous studies on global concentrations and emissions have mostly relied on ground-based observations. Here, we assess the global concentrations and emissions of eight MP controlled substances and methyl chloride from ACE-FTS (Atmospheric Chemistry Experiment high-resolution infrared Fourier transform spectrometer) satellite observations: CFC-11 (CFCl₃), CFC-12 (CF₂Cl₂), CCl₄, HCFC-22 (CHClF₂), HCFC-141b (C₂H₃Cl₂F), HCFC-142b (C₂H₃ClF₂), HFC-23 (CHF₃), HFC-134a (C₂H₂F₄), and CH₃Cl. Results show that the ACE-FTS satellite observations can be used to derive the concentrations and emissions of these ODSs, HFCs, and CH₃Cl, as they are consistent with those derived from the ground-based observations. Our findings imply that the changes in the concentrations and emissions of the ODSs and HFCs closely match the regulatory status of the MP, and satellite observations can be used to monitor the past and future progress of the MP.

Atmospheric chemistry of nitrous acid and its effects on hydroxyl radical and ozone at the urban area of Beijing in early spring 2021

The atmospheric chemistry of nitrous acid (HONO) has received extensive attention because of its significant contribution to hydroxyl (OH) radicals. Heterogeneous reaction of NO₂ is an important HONO source, and its reaction mechanism is affected by many factors, such as concentration of gaseous NO₂, surface adsorbed water, relative humidity and temperature. Although laboratory studies have confirmed the effect of temperature on heterogeneous reaction of NO₂, there are few field observations reporting about it. We have conducted a field observation in the early spring 2021 when the temperature ranges widely (-0.1-24.7 °C). Concentrations of HONO and related pollutants at the urban area of Beijing are obtained. The hourly averaged HONO concentration reaches 4.87 ppb with a mean value of 1.48 ± 1.09 ppb. Combined with box model and RACM2 mechanism, we found an optimal temperature (∼10 °C) existing for heterogeneous reaction of NO₂ during this measurement. When considering the promotion effect of optimal temperature, the contribution of heterogeneous reaction of NO₂ to HONO can increase by 10%. This result will provide essential information for developing an accurate model of HONO chemistry in the atmosphere especially for certain periods or regions with temperature changing largely. Moreover, heterogeneous reaction of NO₂ is the vital source of HONO, contributing 63-76% to simulated HONO during this measurement. Note that HONO photolysis is the most important formation pathway of OH radicals, and ambient HONO concentration is the obbligato constraint for evaluating atmospheric oxidation by model simulations.

Relation of pandemics with solar cycles through ozone, cloud seeds, and vitamin D

The global records of infectious diseases, including Western and Eastern documents from 1825 to 2020, during which sunspot observations are considered reliable, show that 27 of the 34 pandemic outbreaks were coincident with sunspot number maxima or minima. There is evidence that the intensity of galactic cosmic rays is anti-correlated with solar activity and that cloud seed formation is accelerated by galactic cosmic rays. There are a substantial number of research papers showing the relationship between COVID-19 and vitamin D deficiency. The data analysis of ozone thickness measured based on NASA satellite observations revealed that ozone thickness has 11-year and 28-month cycles. Because the 11-year cycles of ozone thickness and cloud seed attenuation are anti-correlated, when either one becomes extremely thick, such as at the maximum or minimum point of solar activity, UV radiation is over-attenuated, and human vitamin D deficiency is globally increased. This finding explains the coincidence of pandemic outbreaks with the extrema of the sunspot numbers. Vitamin D supplementation can be an effective countermeasure against the spread of infectious diseases, which is a paramount importance to global society. Future pandemic forecasting should include the 11-year and 28-month cycles of UV radiation. This founding completes the relationship between solar activity and human health through the earth's environment.

A pilot lab trial for enhanced oxidative transformation of procymidone fungicide and its aniline metabolite using heterogeneous MnO2 catalysts

In this study, the feasibility of two heterogeneous catalysis (non-Fenton heterogeneous catalysis and catalytic ozonation) was evaluated for the oxidative transformation of the fungicide procymidone and its major metabolite (3,5-dichloroaniline; 3,5-DCA) under a pilot lab experiment. Among the studied treatments, only H₂O₂ or O₃ significantly oxidized procymidone and 3,5-DCA. However, heterogeneous catalysis used with various types of MnO₂ catalysts was found to be an effective rapid strategy for transformation of procymidone and its aniline metabolite. Among the studied catalysts, δ-MnO₂ performed well in the enhanced oxidative transformation of procymidone and 3,5-DCA in MnO₂-mediator system assay. The optimal reaction parameters, such as reaction pH, and initial catalyst concentration were comparatively evaluated. However, heterogeneous catalysis and catalytic ozonation were revealed as the rapid strategy for oxidative transformation of investigated procymidone and 3,5-DCA as compared to single oxidation by peroxide/ozone. Finally, as a novel insight of this investigation, a postulated reaction mechanism underlying the accelerated transformation of aniline metabolites via heterogeneous catalysis was explored. The findings of this study will open new avenues for evaluating heterogeneous catalysis during oxidative transformation of non-phenolic pollutants in both lab trial and field applications. This study can be expanded for use in actual field settings, using environmental samples from contaminated areas exposed to non-phenolic pesticides and their metabolites.

Analysis of VOC emissions and O3 control strategies in the Fenhe Plain cities, China

Long-term continuous hourly measurements of ambient volatile organic compounds (VOCs) are scarce at the regional scale. In this study, a one-year hourly measurement campaign of VOCs was performed in Lvliang, Linfen, and Yuncheng in the heavily polluted Fenhe Plain region in China. The VOC average (±standard deviation, std) concentrations in Lvliang, Linfen, and Yuncheng were 44.4 ± 24.9, 45.7 ± 24.9, and 37.5 ± 25.0 ppbv, respectively. Compared to published data from the past two decades in China, the observed VOCs were at high concentration levels. VOCs in the Fenhe Plain cities were significantly impacted by industrial sources according to calculated emission ratios but were less affected by liquefied petroleum gas and natural gas (LPG/NG) and traffic emissions than those in megacities abroad. The emission inventories and observation data were combined for verification and identification of the key VOC species and sources controlling ozone (O₃). Industrial emissions were the largest source of VOCs, accounting for 65%-79% of the total VOC emissions, while the coking industry accounted for 45.2%-66.0%. The emission inventories significantly underestimated oxygenated VOC (OVOC) emissions through the verification of VOC emission ratios. O₃ control scenarios were analyzed by changing VOC/NO_X reduction ratios through a photochemical box model. O₃ control strategies were formulated considering local pollution control plans, emission inventories, and O₃ formation regimes. The O₃ reduction of reactivity-control measures was comparable with emission-control measures, ranging from 16% to 41%, which was contrary to the general perception that ozone formation potential (OFP)-based measures were more efficient for O₃ reduction. Sources with high VOC emissions are accompanied by high OFP on the Fenhe Plain, indicating that the control of high-emission sources can effectively mitigate O₃ pollution on this region.

Improvement of coal gasification reverse osmosis concentrate treatment by Cu-Co-Mn/AC catalytic ozonation

Approximately 20% of concentrate will be produced from coal gasification wastewater after reverse osmosis treatment. The organic matter contained in the concentrate affects its evaporation crystallisation; therefore, the refractory organics must be removed. In this study, Cu-Co-Mn/AC catalytic ozonation was used to treat reverse osmosis concentrate (ROC). With the addition of the Cu-Co-Mn/AC catalyst, the production of ·OH increased by 82 μmol/L, thereby enhancing the ozonation performance. The pH, ozone dosage, and catalyst dosage all affected the catalytic ozonation performance. By constructing a response surface model, it was found that the catalyst dosage had the most significant effect on the catalytic ozonation performance. The predicted optimal reaction conditions were pH = 9.02, ozone dosage = 1.08 g/L, and catalyst dosage = 1.33 g/L, under which the chemical oxygen demand (COD) removal reached a maximum of 81.49%.

Formaldehyde Decomposition from -20 °C to Room Temperature on a Mn-Mullite YMn2O5 Catalyst

Large ambient temperature changes (-20->25 °C) bring great challenges to the purification of the indoor pollutant formaldehyde. Within such a large ambient temperature range, we herein report a manganese-based strategy, that is, a mullite catalyst (YMn₂O₅) + ozone, to efficiently remove the formaldehyde pollution. At -20 °C, the formaldehyde removal efficiency reaches 62% under the condition of 60,000 mL g_cat^-1 h^-1. As the reaction temperature is increased to -5 °C, formaldehyde and ozone are completely converted into CO₂, H₂O, and O₂, respectively. Such a remarkable performance was ascribed to the highly reactive oxygen species generated by ozone on the YMn₂O₅ surface based on the low temperature-programed desorption measurements. The in situ infrared spectra showed the intermediate product carboxyl group (-COOH) to be the key species. Based on the superior performance, we built a consumable-free air purifier equipped with mullite-coated ceramics. In the simulated indoor condition (25 °C and 30% relative humidity), the equipment can effectively decompose formaldehyde (150 m³ h^-1) without producing secondary pollutants, rivaling a commercial removal efficiency. This work provides an air purification route based on the mullite catalyst + ozone to remove formaldehyde in an ambient temperature range (-20->25 °C).

Manipulating Selectivity of Hydroxyl Radical Generation by Single-Atom Catalysts in Catalytic Ozonation: Surface or Solution

Hydroxyl radical-dominated oxidation in catalytic ozonation is, in particular, important in water treatment scenarios for removing organic contaminants, but the mechanism about ozone-based radical oxidation processes is still unclear. Here, we prepared a series of transitional metal (Co, Mn, Ni) single-atom catalysts (SACs) anchored on graphitic carbon nitride to accelerate ozone decomposition and produce highly reactive ·OH for oxidative destruction of a water pollutant, oxalic acid (OA). We experimentally observed that, depending on the metal type, OA oxidation occurred dominantly either in the bulk phase, which was the case for the Mn catalyst, or via a combination of the bulk phase and surface reaction, which was the case for the Co catalyst. We further performed density functional theory simulations and in situ X-ray absorption spectroscopy to propose that the ozone activation pathway differs depending on the oxygen binding energy of metal, primarily due to differential adsorption of O₃ onto metal sites and differential coordination configuration of a key intermediate species, *OO, which is collectively responsible for the observed differences in oxidation mechanisms and kinetics.

Integrated strategies for robust growth of Chlorella vulgaris on undiluted dairy farm liquid digestate and pollutant removal

Undiluted dairy farm liquid digestate contains high levels of organic matters, chromaticity and total ammonia nitrogen (TAN), resulting in inhibition to microalgal growth. In this study, a novel cascade pretreatment with ozonation and ammonia stripping (O + S) was employed to remove these inhibitors, and was compared with single pretreatment approach. The optimum parameters for ozonation and ammonia stripping were obtained and the mechanisms of inhibition elimination were investigated. The results show that ozonation contributed to the degradation of non-fluorescent chromophoric organics through the direct molecular ozone attack, which mitigated the inhibition of chromaticity to microalgae, while ammonia stripping relieved the inhibition of high TAN to microalgae. After cascade pretreatment, TAN, total nitrogen (TN), COD and chromaticity were reduced by 80.2 %, 75.4 %, 20.6 % and 75.8 % respectively. When C. vulgaris was cultured on different pretreated digestate, it was found that cascade pretreatment was beneficial for retaining high PSII activity and synergistically improved microalgal growth. The highest biomass increment and productivity achieved 5.40 g L^-1 and 900 mg L^-1 d^-1 respectively in the integration system of cascade pretreatment with microalgae cultivation (O + S + M). After O + S + M treatment, the removal efficiencies of TAN, TN, COD and total phosphorus (TP) were 100 %, 92.8 %, 46.7 % and 99.6 %, respectively. This work provided a promising strategy (O + S + M) for sustainable liquid digestate treatment, along with nutrient recovery and value-added biomass production.

Partitioning of reactive oxygen species from indoor surfaces to indoor aerosols

Reactive oxygen species (ROS) are among the species thought to be responsible for the adverse health effects of particulate matter (PM) inhalation. Field studies suggest that indoor sources of ROS contribute to measured ROS on PM in indoor air. We hypothesize that ozone reacts on indoor surfaces to form semi-volatile ROS, in particular organic peroxides (OPX), which partition to airborne particles. To test this hypothesis, we modeled ozone-induced formation of OPX, its decay and its partitioning to PM in a residential building and compared the results to field measurements. Simulations indicate that, while ROS of outdoor origin is the primary contributor to indoor ROS (in PM), a substantial fraction of ROS present in indoor PM is from ozone-surface chemistry. At an air change rate equal to 1/h, and an outdoor ozone mixing ratio of 35 ppb, 25% of the ROS concentration in air is due to indoor formation and partitioning of OPX to PM. For the same conditions, but with a modest indoor source of PM (1.5 mg h^-1), 44% of indoor ROS on PM is of indoor origin. An indoor source of ozone, such as an electrostatic air cleaner, also increases OPX present in indoor PM. The results of the simulations support the hypothesis that ozone-induced formation of OPX on indoor surfaces, and subsequent partitioning to aerosols, is sufficient to explain field observations. Therefore, indoor sourced ROS could contribute meaningfully to total inhaled PM-ROS.

Suppression of the phenolic SOA formation in the presence of electrolytic inorganic seed

Phenolic compounds are largely attributed to wildfire gases and rapidly react with atmospheric oxidants to form persistent phenoxy free radicals, which influence atmospheric chemistry and secondary organic aerosol (SOA) formation. In this study, phenol or o-cresol was photochemically oxidized under various conditions (NO_x levels, humidity, and seed conditions) in an outdoor photochemical reactor. Unexpectedly, SOA growth of both phenols was suppressed in the presence of salted aqueous aerosol compared to non-seed SOA. This discovery is different from the typical SOA formation of aromatic or biogenic hydrocarbons, which show noticeably higher SOA yields via organic aqueous reactions. Phenol, o-cresol, and their phenolic products (e.g., catechols) are absorbed in aqueous aerosol and form phenoxy radicals via heterogeneous reactions under sunlight. The resulting phenoxy radicals are redistributed between the gas and particle phases. Gaseous phenoxy radicals quickly react with ozone to form phenyl peroxide radicals and regenerated through a NO_x cycle to retard phenol oxidation and SOA formation. The explicit oxidation mechanisms of phenol or o-cresol in the absence of aqueous phase were derived including the Master Chemical Mechanism (MCM v3.3.1) and the path for peroxy radical adducts originating from the addition of an OH radical to phenols to form low volatility products (e.g., multi-hydroxy aromatics). The resulting gas mechanisms of phenol or o-cresol were, then, applied to the Unified Partitioning Aerosol Phase Reaction (UNIPAR) model to predict SOA formation via multiphase partitioning of organics and aerosol-phase oligomerization. The model well simulated chamber-generated phenolic SOA in absence of wet-inorganic seed, but significantly overestimated SOA mass in presence of wet seed. This study suggests that heterogeneous chemistry to form phenoxy radicals needs to be included to improve SOA prediction from phenols. The suppression of atmospheric oxidation due to phenoxy radicals in wet inorganic aerosol can explain the low SOA formation during wildfire episodes.

Photocatalytic Oxidation of Carbon Monoxide Using Synergy of Redox-Separated Photocatalyst and Ozone

Separating the redox centers of photocatalysts is the most promising strategy to enhance photocatalytic oxidation efficiency. Herein, I investigate a site-selective loading of Pt on facet-engineered TiO₂ to achieve carbon monoxide (CO) oxidation at room temperature. Spatially loaded Pt on {101} facets of TiO₂ attracts photoinduced electrons efficiently. Thereby, oxygen dissociation is facilitated on the Pt surface, which is confirmed by enhanced oxidation of CO by 2.4 times compared to the benchmark of Pt/TiO₂. The remaining holes on TiO₂ can be utilized for the oxidation of various gaseous pollutants. Specifically, gaseous ozone, which is present in indoor and ambient air, is converted to a hydroxyl radical by reacting with the hole; thus, the poisoned Pt surface is continuously cleaned during the CO oxidation, as confirmed by in situ diffuse reflectance infrared transform spectroscopy. While randomly loaded Pt can act as recombination center, reducing photocatalytic activity, redox-separated photocatalyst enhances charge separation, boosting CO oxidation and catalyst regeneration via simultaneous ozone decomposition.

Treatment of micropollutants in wastewater: Balancing effectiveness, costs and implications

In this contribution, we analyse scenarios of advanced wastewater treatment for the removal of micropollutants. By this we refer to current mainstream, broad spectrum processes including ozonation and sorption onto activated carbon. We argue that advanced treatment requires properly implemented tertiary (nutrient removal) treatment in order to be effective. We review the critical aspects of the main advanced treatment options, their advantages and disadvantages. We propose a quantification of the costs of implementing advanced treatment, as well as upgrading plants from secondary to tertiary treatment when needed, and we illustrate what drives the costs of advanced treatment for a set of standard configurations. We propose a cost function to represent the total costs (investment, operation and maintenance) of advanced treatment. We quantify the implications of advanced treatment in terms of greenhouse gas emissions. Based on the indicators of total toxic discharge, toxicity at the discharge points and toxicity across the stream network discussed in Pistocchi et al. (2022), we compare costs and effectiveness of different scenarios of advanced treatment. In principle the total toxic load and toxicity at the points of discharge could be reduced by about 75 % if advanced treatment processes were implemented virtually at all wastewater treatment plants, but this would entail costs of about 4 billion euro/year for the European Union as a whole. We consider a "compromise" scenario where advanced treatment is required at plants of 100 thousand population equivalents (PE) or larger, or at plants between 10 and 100 thousand PE if the dilution ratio at the discharge point is 10 or less. Under this scenario, the length of the stream network exposed to high toxicity would not increase significantly compared to the previous scenario, and the other indicators would not deteriorate significantly, while the costs would remain at about 1.5 billion Euro/year. Arguably, costs could be further reduced, without a worsening of water quality, if we replace a local risk assessment to generic criteria of plant capacity and dilution in order to determine if a WWTP requires advanced treatment.

Study on the spatiotemporal dynamic of ground-level ozone concentrations on multiple scales across China during the blue sky protection campaign

Surface ozone (O₃), one of the harmful air pollutants, generated significantly negative effects on human health and plants. Existing O₃ datasets with coarse spatiotemporal resolution and limited coverage, and the uncertainties of O₃ influential factors seriously restrain related epidemiology and air pollution studies. To tackle above issues, we proposed a novel scheme to estimate daily O₃ concentrations on a fine grid scale (1 km × 1 km) from 2018 to 2020 across China based on machine learning methods using hourly observed ground-level pollutant concentrations data, meteorological data, satellite data, and auxiliary data including digital elevation model (DEM), land use data (LUD), normalized difference vegetation index (NDVI), population (POP), and nighttime light images (NTL), and to identify the difference of influential factors of O₃ on diverse urbanization and topography conditions. Some findings were achieved. The correlation coefficients (R²) between O₃ concentrations and surface net solar radiation (SNSR), boundary layer height (BLH), 2 m temperature (T2M), 10 m v-component (MVW), and NDVI were 0.80, 0.40, 0.35, 0.30, and 0.20, respectively. The random forest (RF) demonstrated the highest validation R² (0.86) and lowest validation RMSE (13.74 μg/m³) in estimating O₃ concentrations, followed by support vector machine (SVM) (R² = 0.75, RMSE = 18.39 μg/m³), backpropagation neural network (BP) (R² = 0.74, RMSE = 19.26 μg/m³), and multiple linear regression (MLR) (R² = 0.52, RMSE = 25.99 μg/m³). Our China High-Resolution O₃ Dataset (CHROD) exhibited an acceptable accuracy at different spatial-temporal scales. Additionally, O₃ concentrations showed decreasing trend and represented obviously spatiotemporal heterogeneity across China from 2018 to 2020. Overall, O₃ was mainly affected by human activities in higher urbanization regions, while O₃ was mainly controlled by meteorological factors, vegetation coverage, and elevation in lower urbanization regions. The scheme of this study is useful and valuable in understanding the mechanism of O₃ formation and improving the quality of the O₃ dataset.

Fifty-year change in air pollution in Kaohsiung, Taiwan

The change in air quality in cities can be the product of regulation and emissions. Regulations require enforcement of emission reduction, but it is often shifting economic and societal structures that influence pollutant emissions. This study examines the long-term record of air pollutants in Kaohsiung, where post-war industrialisation increased pollution substantially, although improvements are observed in recent decades as the city moved to a more mixed economy. The study tracks both gases and particles across a period of significant change in pollution sources in the city. Concentrations of SO₂ and aerosol SO₄^2- were especially high ~1970, but these gradually declined, although SO₄^2- to a lesser extent than its precursor, SO₂. While twenty-first century emissions of SO₂ and NO_x have declined, this has been less so for NH₃, because it arises from predominantly agricultural sources. The atmosphere in Kaohsiung continues to have high concentrations of O₃, and these have risen in the city, likely a product of less titration by NO. The changes have meant that ozone has become an increasing threat to health and agriculture. Despite a potential for producing (NH₄)₂SO₄ and NH₄NO₃ aerosols, a product of a relatively constant supply of NH₃, visibility has improved in recent years. Emissions of SO₂ and NO_x should continue to be reduced, as these strongly affect the amount of fine secondary aerosol. However, the key problem may be ozone, which is difficult to control as it requires careful consideration of the balance of NO_x and hydrocarbons so important to its production.

Recent advances in sterilization and disinfection technology: A review

Sterilization and disinfection of pollutants and microorganisms have been extensively studied in order to address the problem of environmental contamination, which is a crucial issue for public health and economics. Various form of hazardous materials/pollutants including microorganisms and harmful gases are released into the environment that enter into the human body either through inhalation, adsorption or ingestion. The human death rate rises due to various respiratory ailments, strokes, lung cancer, and heart disorders related with these pollutants. Hence, it is essential to control the environmental pollution by applying economical and effective sterilization and disinfections techniques to save life. In general, numerous forms of traditional physical and chemical sterilization and disinfection treatments, such as dry and moist heat, radiation, filtration, ethylene oxide, ozone, hydrogen peroxide, etc. are known along with advanced techniques. In this review we summarized both advanced and conventional techniques of sterilization and disinfection along with their uses and mode of action. This review gives the knowledge about the advantages, disadvantages of both the methods comparatively. Despite, the effective solution given by the advanced sterilization and disinfection technology, joint technologies of sterilization and disinfection has proven to be more effective innovation to protect the indoor and outdoor environments.

Ni-based catalysts used in heterogeneous catalytic ozonation for organic pollutant degradation: a minireview

Among various advanced oxidation processes for wastewater treatment, heterogeneous catalytic ozonation (HCO) has a growing interest in pollutant degradation, e.g., pesticides, pharmaceuticals, cresols, detergents, polymers, dyes, and others. Direct oxidation with ozone can occur by this route or indirectly, generating reactive oxygen species through the catalytic activation of the ozone molecule. Then, many catalytic materials were evaluated, such as unsupported and supported oxides, activated carbon, nanocarbons, carbon nitride, and mesoporous materials. This review focuses on the properties and performance of Ni-based catalysts (NiO, supported NiO, Ni ferrites, and M-Ni bimetallic), emphasizing the reaction mechanisms and the importance of the reactive oxygen species in removing toxic organic compounds.

Can aged microplastics be transport vectors for organic micropollutants? - Sorption and phytotoxicity tests

Microplastics have been investigated over the last decade as potential transport vectors for other pollutants. However, the specific role of plastic aging, in which plastics change their characteristics over time when exposed to environmental agents, has been overlooked. Therefore, sorption experiments were herein conducted using virgin and aged (by ozone treatment or rooftop weathering) microplastic particles of LDPE - low-density polyethylene, PET - poly(ethylene terephthalate), or uPVC - unplasticized poly(vinyl chloride). The organic micropollutants (OMPs) selected as sorbates comprise a diversified group of priority substances and contaminants of emerging concern, including pharmaceutical substances (florfenicol, trimethoprim, diclofenac, tramadol, citalopram, venlafaxine) and pesticides (alachlor, clofibric acid, diuron, pentachlorophenol), analyzed at trace concentrations (each ≤100 μg L^-1). Sorption kinetics and equilibrium isotherms were obtained, as well as the confirmation that the aging degree of microplastics plays a major role in their sorption capacities. The results show an increased sorption of several OMPs on aged microplastics when compared to pristine samples, i.e. the sorption capacity increasing from one or two sorbed substances (maximum 3 μg g^-1 per sorbate) up to nine after aging (maximum 10 μg g^-1 per sorbate). The extent of sorption depends on the OMP, polymer and the effectiveness of the aging treatment. The modifications (e.g. in the chemical structure) between virgin and aged microplastics were linked to the increased sorption capacity of certain OMPs, allowing to better understand the different affinities observed. Additionally, phytotoxicity tests were performed to evaluate the mobility of the OMPs sorbed on the microplastics and the potential effects (on germination and early growth) of the combo on two species of plants (Lepidium sativum and Sinapis alba). These tests suggest low or no phytotoxicity effect under the conditions tested but indicate a need for further research on the behavior of microplastics on soil-plant systems.

Application of poly aluminum chloride and alum as catalyst in catalytic ozonation process after coagulation for the treatment of textile wastewater

Textile wastewater is ranked highly contaminated among all industrial waste. During textile processing, the consumption of dyes and complex chemicals at various stages makes textile industrial wastewater highly challenging. Therefore, conventional processes based on single-unit treatment may not be sufficient to comply with the environmental quality discharge standards and more stringent guidelines for zero discharge of hazardous chemicals (ZDHC). In this study, a novel approach was followed by recycling Poly aluminum chloride (PACl) and Alum as a catalyst for the first time in the catalytic ozonation treatment process leading to a nascent method after using them as a coagulant in Coagulation/Flocculation. In the current investigation, six different combinations were studied to remove turbidity, TSS, COD, BOD₅, color, and biodegradability (BOD₅/COD ratios) of wastewater. Moreover, Central Composite Design was implied using RSM in Minitab software. During the combination of treatment processes, it was found that the pre-coagulation/flocculation with coagulant PACl followed by post-catalytic ozonation with recycled PACl, a more effective treatment than others. The optimum R.E of turbidity, TSS, COD, and color were 84%, 86%, 89%, and 98%, respectively. Moreover, a decrease in toxicity and increase in biodegradability (BOD₅/COD ratio from 0.29 to 0.54) was observed as well. The electrical energy demand and operational costs of treatment processes were estimated and compared with other treatment processes.

Modeling carbonate/bicarbonate and nitrate disturbance during secondary effluent disinfection by UV/H2O2 and UV/ozone

The disinfection of effluents has been considered the main step to inactivate pathogenic organisms to prevent the spread of waterborne diseases. The variation in the matrix composition can lead to the use of inadequate oxidant dose and disturb a correct treatment. The objective of this study was to develop a simple and practical mathematical model to simulate the disturbance of inorganic anions (CO₃^2-/HCO₃^- and NO₃^-) during secondary effluent disinfection by UV/H₂O₂ and UV/O₃. The pathogenic agents chosen for this study were total coliforms and E. coli. To build the mathematical model, a modification of the Chick model (referred to as 'Modified Chick Model') was proposed by employing a weighted average in the calculation of the kinetic constant. Both treatments were affected by the presence of the anions. However, with the highest NO₃^- concentration, less inhibition of disinfection was observed in the UV/H₂O₂. The use of the arithmetic means to calculate the value of k, as indicated by the Chick model, demonstrates a lesser precision in the prediction of the microorganisms' concentrations. On the other hand, using the Modified Chick Model, a better prediction of the inactivation of the microorganisms was obtained, which can be confirmed by the validation performed.

Physical activity attenuated the association of ambient ozone with type 2 diabetes mellitus and fasting blood glucose among rural Chinese population

The association of ozone with type 2 diabetes mellitus (T2DM) is uncertain. Moreover, the moderating effect of physical activity on this association is largely unknown. This study aims to evaluate the independent and combined effects of ozone and physical activity on T2DM and fasting blood glucose (FBG) in a Chinese rural adult population. A total of 39,192 participants were enrolled in the Henan Rural Cohort Study. Individual ozone exposure was assessed by using a satellite-based random forest model. The logistic regression and generalized linear models were used to evaluate the associations of ozone and physical activity with T2DM and FBG, respectively. Interaction plots were used to visualize the interaction effects of ozone and physical activity on T2DM or FBG. An interquartile range (IQR) increase in ozone exposure concentration was related to a 53.3% (odds ratio (OR),1.533; 95% confidence interval (CI), 1.426, 1.648) increase in odds of T2DM and a 0.292 mmol/L (95%CI, 0.263, 0.321) higher FBG level, respectively. The effects of ozone on T2DM and FBG generally decreased as physical activity levels increased. Negative additive interactions between ozone and physical activity on T2DM risk were observed (relative excess risk due to interaction (RERI), -0.261; 95%CI, -0.473, -0.048; attributable proportion due to interaction (AP), -0.203; 95%CI, -0.380, -0.027; synergy index (S), 0.520; 95%CI, 0.299, 0.904). The larger effects of ozone were observed among elderly and men on T2DM and FBG than young and women. Long-term exposure to ozone was associated with higher odds of T2DM and higher FBG levels, and these associations might be attenuated by increasing physical activity levels. In addition, there was a negative additive interaction (antagonistic effect) between ozone exposure and physical activity level on T2DM risk, suggesting that physical activity might be an effective method to reduce the burden of T2DM attributed to ozone exposure. Trail registration: The Henan Rural Cohort Study has been registered at Chinese Clinical Trial Register (registration number: ChiCTR-OOC-15006699). Date of registration: 06 July 2015, http://www.chictr.org.cn/showproj.aspx?proj=11375.

Tracking short-term health impacts attributed to ambient PM2.5 and ozone pollution in Chinese cities: an assessment integrates daily population

Joint and synergistic control of PM_2.5 and ozone pollution is an urgent need in China and a global-widely concerned issue. Health impact assessment could provide a comprehensive perspective for PM_2.5-ozone coordinated control strategies. For a detailed understanding of the seasonality and regionality of the health impacts attributed to PM_2.5 and ozone in China, this study extended the classic health impact function by daily population and assessed the short-term (daily) health impacts in 335 Chinese cities in 2021. Population migration indexes from Baidu were introduced to estimate the cities' daily population. Using this method, we quantitatively investigated the influence of population on short-term health impact assessment and identified which was significant in the Pearl River Delta (PRD) region and other populous cities. Although the annual sums of PM_2.5- and ozone-related daily health impacts were close for all Chinese cities, the PM_2.5-related health impact was equivalent to 333.96% and 32.07% of that ozone-related, during the cold and warm periods. The correlation and local spatial association analysis found significant city-specific and city-cluster associations of daily health impacts during the warm period and in Beijing-Tianjin-Hebei and surrounding regions (BTHS) and the Yangtze River Delta (YRD). Policymakers could promote period- and pollutant-targeted control actions for the major city groups, especially the BTHS, YRD, and PRD. Our methods and findings investigated the various influences of the population on short-term health impact assessment and proposed the PM_2.5-ozone collaborative control idea for key regions and city groups.

Optimization for minimizing the cost of ozonation of highly concentrated textile dyeing wastewater in a bubble column reactor

Ozonation is one of the advanced oxidation methods that provide effective decolorization and detoxification of the dyeing wastewater without causing any sludge formation. Despite being a good alternative to biodegradation, ozonation suffers from a high operating cost. This study conducted the ozonation process at high initial dye concentrations and optimized the process parameters (such as initial ozone concentration, initial dye concentration, and pH) to minimize the operating cost in terms of the overall power consumption of the process. The ozonation of Reactive Blue dye was performed in a bubble column reactor at various process conditions. A central composite design (CCD)-based response surface method (RSM) statistical tool was used to optimize the process. An empirical correlation for the specific power consumption (defined as electricity consumed per unit mass of dye removed from a unit volume of dyeing wastewater) was developed and verified. It was found that the specific power consumption during ozonation can be lowered significantly (by ~25-30%) if the dyeing water was treated at high initial dye concentrations.

Simulation on oily contamination removal by ozone using molecular dynamics

Ozone (O₃) is characteristic of high oxidative activity. It displays a high potential value in sterilization and decontamination. Although O₃ has been widely investigated for its efficiency and environmentally friendly effectiveness, the fundamental issue regarding the complicated microscopic interaction mechanism between O₃ and contaminant molecules remains largely unaddressed. We addressed this knowledge gap through molecular dynamics (MD) simulation at the molecular scale. Results indicated that five representative hydrocarbon molecules (n-hexadecane, phytane, terpane, naphthalin and acenaphthylene) on a rough silica (SiO₂) surface were almost removed after about 300 ps simulation. And the aromatic molecules were easier to be removed than aliphatic ones. The hydroxyl oxidation reaction was demonstrated as a predominant mechanism. As the large dose of O₃ was supplied by atmospheric air dielectric barrier discharge (DBD) plasma, this work provided an important theoretical reference for better using plasma technology for oily contaminant removal.

Insights into the microbial degradation and resistance mechanisms of glyphosate

Glyphosate, as one of the broad-spectrum herbicides for controlling annual and perennial weeds, is widely distributed in various environments and seriously threatens the safety of human beings and ecology. Glyphosate is currently degraded by abiotic and biotic methods, such as adsorption, photolysis, ozone oxidation, and microbial degradation. Of these, microbial degradation has become the most promising method to treat glyphosate because of its high efficiency and environmental protection. Microorganisms are capable of using glyphosate as a phosphorus, nitrogen, or carbon source and subsequently degrade glyphosate into harmless products by cleaving C-N and C-P bonds, in which enzymes and functional genes related to glyphosate degradation play an indispensable role. There have been many studies on the abiotic and biotic treatment technologies, microbial degradation pathways and intermediate products of glyphosate, but the related enzymes and functional genes involved in the glyphosate degradation pathways have not been further discussed. There is little information on the resistance mechanisms of bacteria and fungi to glyphosate, and previous investigations of resistance mechanisms have mainly focused on how bacteria resist glyphosate damage. Therefore, this review explores the microorganisms, enzymes and functional genes related to the microbial degradation of glyphosate and discusses the pathways of microbial degradation and the resistance mechanisms of microorganisms to glyphosate. This review is expected to provide reference for the application and improvement of the microbial degradation of glyphosate in microbial remediation.

Different degradation mechanisms of low-concentration ozone for MIL-100(Fe) and MIL-100(Mn) over wide humidity fluctuation

The synergistic control of ozone and fine particulate matter is a research hotspot in the current environmental fields. Among the ozone removal, wide humidity fluctuation and low concentration dynamic adsorption are two thorny problems. In this work, MIL-100(Fe) and MIL-100(Mn), synthesized by hydrothermal and solvothermal methods respectively, were selected to investigate the degradation of flowing ozone pollutants. The samples showed different ozone degradation mechanisms, namely photocatalytic degradation and normal temperature degradation. Notably, MIL-100(Fe) exhibited more outstanding photocatalytic activity than MIL-100(Mn), while the normal temperature catalytic efficiency of MIL-100(Mn) was much superior to MIL-100(Fe). For different humidity conditions, MIL-100(Fe) has the optimal photocatalytic performance at 10% humidity, which is 38%, while MIL-100(Mn) has basically no change in normal temperature catalytic degradation efficiency at different humidity levels of 10-90%. Furthermore, the degradation mechanism was proposed by in-situ DRIFTS and ESR, which was significantly correlated with oxygen vacancy and photogenerated electron efficiency. By the aid of Temperature Programmed Desorption (TPD), a large quantity of Lewis acid sites was detected in MIL-100(Mn), which was the critical factor that the selected materials could maintain excellent normal temperature degradation performance under high humidity. This work will expand the practical application of ozone removal and improve the degradation efficiency.

Techniques for remediation of pharmaceutical pollutants using metal organic framework - Review on toxicology, applications, and mechanism

Treatment of recalcitrant and xenobiotic pharmaceutical compounds in polluted waters have gained significant attention of the environmental scientists. Antibiotics are diffused into the environment widely owing to their high usages, very particularly in the last two years due to over consumption during covid 19 pandemic worldwide. Quinolones are very effective antibiotics, but do not get completely metabolized due to which they pose severe health hazards if discharged without proper treatment. The commonly reported treatment methods for quinolones are adsorption and advanced oxidation methods. In both the treatment methods, metal organic frameworks (MOF) have been proved to be promising materials used as stand-alone or combined technique. Many composite MOF materials synthesized from renewable, natural, and harmless materials by eco-friendly techniques have been reported to be effective in the treatment of quinolones. In the present article, special focus is given on the abatement of norfloxacin and ofloxacin contaminated wastewater using MOFs by adsorption, oxidation/ozonation, photocatalytic degradation, electro-fenton methods, etc. However, integration of adsorption with any advanced oxidation methods was found to be best remediation technique. Of various MOFs reported by several researchers, the MIL-101(Cr)-SO₃H composite was able to give 99% removal of norfloxacin by adsorption. The MIL - 88A(Fe) composite and Fe LDH carbon felt cathode were reported to yield 100% degradation of ofloxacin by photo-Fenton and electro-fenton methods respectively. The synthesis methods and mechanism of action of MOFs towards the treatment of norfloxacin and ofloxacin as reported by several investigation reports are also presented.

A comprehensive review on green perspectives of electrocoagulation integrated with advanced processes for effective pollutants removal from water environment

The rapidly expanding global energy demand is forcing a release of regulated pollutants into water that is threatening human health. Among various wastewater remediating processes, electrocoagulation (EC) has scored a monumental success over conventional processes because it combines coagulation, sedimentation, floatation and electrochemical oxidation processes that can effectively decimate numerous stubborn pollutants. The EC processes have gained some attention through various academic and industrial publications, however critical evaluation of EC processes, choices of EC processes for various pollutants, process parameters, mechanisms, commercial EC technologies and performance enhancement via other degradation processes (DPs) integration have not been comprehensively covered to date. Therefore, the major objective of this paper is to provide a comprehensive review of 20 years of literature covering EC fundamentals, key process factors for a reactor design, process implementation, current challenges and performance enhancement by coupling EC with pivotal pollutant DPs including, electro/photo-Fenton (E/P-F), photocatalysis, sono-chemical treatment, ozonation, indirect electrochemical/advanced oxidation (AO), and biosorption that have substantially reduced metals, pathogens, toxic compound BOD, COD, colors in wastewater. The results suggest that the optimum treatment time, current density, pulse frequency, shaking speed and spaced electrode improve the pollutants removal efficiency. An elegant process design can prevent electrode passivation which is a critical limitation of EC technology. EC coupling (up or downstream) with other DPs has resulted in the removal of organic pollutants and heavy metals with a 20% improved efficiency by EC-EF, removal of 85.5% suspended solid, 76.2% turbidity, 88.9% BOD, 79.7% COD and 93% color by EC-electroflotation, 100% decolorization by EC-electrochemical-AO, reduction of 78% COD, 81% BOD, 97% color by EC-ozonation and removal of 94% ammonia, 94% BOD, 95% turbidity, >98% phosphorus by aerated EC and peroxicoagulation. The major wastewater purification achievements, future potential and challenges are described to model the future EC integrated systems.

Ozone disinfection efficiency against airborne microorganisms in hospital environment: a case study

Even though ozone has shown its potential for air disinfection in hospital environment, its more frequent use has earned attention only with the COVID-19 pandemic due to its proven antimicrobial effect and low cost of production. The aim of this study was to determine its antimicrobial efficiency against the most common bacterial species in a real-life setting, that is, in the air of one postoperative room of the General Hospital Dr Ivo Pedišić (Sisak, Croatia). Air was sampled for aiborne bacteria before and after treatment with the ozone concentration of 15.71 mg/m3 for one hour. The most dominant Gram-positive bacteria of the genera Micrococcus, Staphylococcus, and Bacillus were reduced by 33 %, 58 %, and 61 %, respectively. The genus Micrococcus proved to be the most resistant. Considering our findings, we recommend longer air treatment with higher ozone concentrations in combination with mechanical cleaning and frequent ventilation.

Recent advances in biopolymer-based advanced oxidation processes for dye removal applications: A review

Over the past few years, synthetic dye-contaminated wastewater has attracted considerable global attention due to the low biodegradability and the ability of organic dyes to persist and remain toxic, causing numerous health and environmental concerns. As a result of the recalcitrant nature of those complex organic dyes, the remediation of wastewater using conventional wastewater treatment techniques is becoming increasingly challenging. In recent years, advanced oxidation processes (AOPs) have emerged as a potential alternative to treat organic dyestuffs discharged from industries. The most widely employed AOPs include photocatalysis, ozonation, Fenton oxidation, electrochemical oxidation, catalytic heterogeneous oxidation, and ultrasound irradiation. These processes involve the generation of highly reactive radicals to oxidize organic dyes into innocuous minerals. However, many conventional AOPs suffer from several setbacks, including the high cost, high consumption of reagents and substrates, self-agglomeration of catalysts, limited reusability, and the requirement of light, ultrasound, or electricity. Therefore, there has been significant interest in improving the performance of conventional AOPs using biopolymers and heterogeneous catalysts such as metal oxide nanoparticles (MONPs). Biopolymers have been widely considered in developing green, sustainable, eco-friendly, and low-cost AOP-based dye removal technologies. They inherit intriguing properties like biodegradability, renewability, nontoxicity, relative abundance, and sorption. In addition, the immobilization of catalysts on biopolymer supports has been proven to possess excellent catalytic activity and turnover numbers. The current review provides comprehensive coverage of different AOPs and how efficiently biopolymers, including cellulose, chitin, chitosan, alginate, gelatin, guar gum, keratin, silk fibroin, zein, albumin, lignin, and starch, have been integrated with heterogeneous AOPs in dye removal applications. This review also discusses the general degradation mechanisms of AOPs, applications of biopolymers in AOPs and the roles of biopolymers in AOPs-based dye removal processes. Furthermore, key challenges and future perspectives of biopolymer-based AOPs have also been highlighted.

Challenges and opportunities in the application of bioinspired engineered nanomaterials for the recovery of metal ions from mining industry wastewater

Heavy-metal-bearing wastewater is among the most formidable challenges the mining industry currently faces in maintaining its social license to operate. Amongst the technologies available for metal ion adsorption, bioinspired engineering nanomaterials have emerged as one which exhibits great promise. However, current processes used for the preparation of adsorbents (including nanoscale activated carbon and biochar) represent a source of adverse impacts on the environment. In contrast, the application of biogenic-nanoparticles, i.e., those derived from processes catalysed by microbiota, has received significant attention in the last few years. Coupled with this, the use of naturally occurring reagents is of major importance for the sustainability of this emerging industry. This paper analyses the life cycle assessment (LCA) of the synthesis of adsorbents derived from agricultural wastes. Moreover, rather than simply recovering the ecotoxic metals from wastewater, the potential to valorise dissolved metals into high-value metallic nanoparticle products is discussed. LCA analysis revealed that the adsorbent had some adverse impact on the environment. The agricultural wastes contributed 27.86% to global warming, 54.64% to ozone formation, 33.06% to fine particles, and 98.24% to marine eutrophication. Mining wastewater is an important, and largely currently unexploited, source of metal value. However, the often-low concentration of such metals dictates that their conversion into high-value products (such as engineered nanoparticles) is an important new research frontier. Within this the use of biosynthesis methods has emerged as having great potential due to a range of beneficial attributes, including low cost, high efficacy and/or environmental compatibility.

Characteristics of atmospheric black carbon and other aerosol particles over the Arctic Ocean in early autumn 2016: Influence from biomass burning as assessed with observed microphysical properties and model simulations

We conducted ship-based measurements of marine aerosol particles (number concentration, size distribution, black carbon (BC), autofluorescence property, and PM_2.5 composition) and trace gases (ozone (O₃) and carbon monoxide (CO)) during a cruise of the R/V Mirai (23 August to 4 October 2016) over the Arctic Ocean, Northwest Pacific Ocean, and Bering Sea. Over the Arctic Ocean at latitudes >70°N, the averaged BC mass concentration was 0.7 ± 1.8 ng/m³, confirming the validity of our previously-reported observations (~1 ng/m³) over the same region during September 2014 and September 2015. The observed levels over the Arctic Ocean need to be used as a benchmark when testing the atmospheric transport models over the ocean, while they are substantially lower than those reported at Barrow (Utqiaġvik), a nearby ground-based station. We identified events with elevated BC mass concentrations and CO mixing ratios over the Arctic Ocean and Bering Sea as influenced by biomass burnings, with evidences from elevated levoglucosan levels, mixing states of BC particles, and particle size distributions. With WRF-Chem model simulations, we confirmed Siberian Forest fire plumes traveled over thousands of kilometers and produced substantially high BC and CO levels over the Bering Sea. The ΔBC/ΔCO ratios during these periods were estimated as ~1 ng/m³/ppbv, which are lower than those values reported, indicating that the results might have been affected by the wet removal process during transportation and/or by emission in smoldering conditions.

Using non-parametric Bayes shrinkage to assess relationships between multiple environmental and social stressors and neonatal size and body composition in the Healthy Start cohort

BACKGROUND

Both environmental and social factors have been linked to birth weight and adiposity at birth, but few studies consider the effects of exposure mixtures. Our objective was to identify which components of a mixture of neighborhood-level environmental and social exposures were driving associations with birth weight and adiposity at birth in the Healthy Start cohort.

METHODS

Exposures were assessed at the census tract level and included air pollution, built environment characteristics, and socioeconomic status. Prenatal exposures were assigned based on address at enrollment. Birth weight was measured at delivery and adiposity was measured using air displacement plethysmography within three days. We used non-parametric Bayes shrinkage (NPB) to identify exposures that were associated with our outcomes of interest. NPB models were compared to single-predictor linear regression. We also included generalized additive models (GAM) to assess nonlinear relationships. All regression models were adjusted for individual-level covariates, including maternal age, pre-pregnancy BMI, and smoking.

RESULTS

Results from NPB models showed most exposures were negatively associated with birth weight, though credible intervals were wide and generally contained zero. However, the NPB model identified an interaction between ozone and temperature on birth weight, and the GAM suggested potential non-linear relationships. For associations between ozone or temperature with birth weight, we observed effect modification by maternal race/ethnicity, where effects were stronger for mothers who identified as a race or ethnicity other than non-Hispanic White. No associations with adiposity at birth were observed.

CONCLUSIONS

NPB identified prenatal exposures to ozone and temperature as predictors of birth weight, and mothers who identify as a race or ethnicity other than non-Hispanic White might be disproportionately impacted. However, NPB models may have limited applicability when non-linear effects are present. Future work should consider a two-stage approach where NPB is used to reduce dimensionality and alternative approaches examine non-linear effects.

Characterization of Various Titanium-Dioxide-Based Catalysts Regarding Photocatalytic Mineralization of Carbamazepine also Combined with Ozonation

Titanium-dioxide-based semiconductors proved to be appropriate for photocatalytic application to efficiently degrade emerging organic pollutants such as various herbicides, pesticides, and pharmaceuticals in waters of environmental importance. The characterization of various TiO2 catalysts, both bare and modified (Ag- and/or N-doped), by mechanochemical treatment was carried out in this work, regarding their structure, morphology, and photocatalytic activity. For the latter investigations, carbamazepine, an antidepressant, proved to be applicable and versatile. The photocatalytic behavior of the catalysts was studied under both UV and visible light. Besides the decomposition efficiency, monitoring the intermediates provided information on the degradation mechanisms. Mechanochemical treatment significantly increased the particle size (from 30 nm to 10 μm), causing a considerable (0.14 eV) decrease in the band gap. Depending on the irradiation wavelength and the catalyst, the activity orders differed, indicating that, in the mineralization processes of carbamazepine, the importance of the different oxidizing radicals considerably deviated, e.g., Ag-TiO2 < DP25-TiO2 < ground-DP25-TiO2 < N-TiO2 ≈ N-Ag-TiO2 for O2•− and N-TiO2 ≈ Ag-TiO2 < N-Ag-TiO2 < ground-DP25-TiO2 ≈ DP25-TiO2 for HO• generation under UV irradiation. Toxicity studies have shown that the resulting intermediates are more toxic than the starting drug molecule, so full mineralization is required. This could be realized by a synergistic combination of heterogeneous photocatalysis and ozonation.

Ultrasonic Auxiliary Ozone Oxidation-Extraction Desulfurization: A Highly Efficient and Stable Process for Ultra-Deep Desulfurization

For ultra-deep desulfurization of diesel fuel, this study applied the ultrasound-assisted catalytic ozonation process to the dibenzothiophene (DBT) removal process with four Keggin-type heteropolyacids (HPA) as catalysts and acetonitrile as extractant. Through experimental evaluations, H₃PMo₁₂O₄₀ was found to be the most effective catalyst for the oxidative removal of DBT. Under favorable operating conditions with a temperature of 0 °C, H₃PMo₁₂O₄₀ dosage of 2.5 wt.% of n-octane, and ultrasonic irradiation, DBT can be effectively removed from simulated diesel. Moreover, the reused catalyst exhibited good catalytic activity in recovery experiments. This desulfurization process has high potential for ultra-deep desulfurization of diesel.

Semicontinuous and batch ozonation combined with peroxymonosulfate for inactivation of microalgae in ballast water

The Ballast Water Management Convention (BWMC) establishes limits regarding the permissible number of viable organisms in discharged ballast water. Ozone as a ballast water treatment is interesting because it can be generated in-situ and has strong oxidant power. Additionally, some oxidants can be formed in reaction with seawater, especially brominated compounds, that assist in inactivating microorganisms. The objective of this study is to assess the efficacy of semicontinuous and batch ozonation as well as their combination with peroxymonosulfate salt (PMS) as methods to be used to ensure compliance with regulation D2 of the BWMC using Tetraselmis suecica as a standard microorganism. Growth modeling method was employed to determine the inactivation achieved by the treatments. The results show that ozone is an effective treatment for accomplishing the D2 of the BWMC. Batch ozonation is more efficient than semicontinuous ozonation probably because of the brominated compounds formed during the ozone saturation of the water. The oxidants that are developed during the ozonation of seawater prolong the residual effect of the treatment throughout the days of storage with practically no presence of them in the ballast tanks at 72 h. The addition of the PMS increases the inactivation in the semicontinuous ozonation, but a threshold concentration of ozone is needed to observe the synergistic effect of both oxidants. No increase is associated with the combination of O₃ and PMS in the case of batch ozonation.