Novel 1-butyl-3-methylimidazolium bromide impregnated chitosan hydrogel beads nanostructure as an efficient nanobio-adsorbent for cationic dye removal: Kinetic study

Crosslinked chitosan-benzil/microalgae/kronos (titanium dioxide) biocomposite for the removal of brilliant green dye: Response surface methodology optimisation and mechanism

In this study, the adsorptive performance of the hydrothermally crosslinked Chitosan- Benzil/Microalgae/Kronos (TiO2) (Cs/Bz2-Ma-KT) biocomposite was evaluated towards removal of brilliant green (BG) a toxic cationic dye. Box-Behnken-Design from Response Surface Methodology (BBD-RSM) was employed for the design of the experiments, statistical analysis of the variables affecting the adsorption process, and finally for the optimisation of the adsorption parameters. The results revealed that the pH of the adsorption environment has the highest impact on the removal of BG dye due to the electrostatic repulsion and attraction occurring in pH values lower and higher than pHpzc of the adsorbent, respectively. The synthesised Cs/Bz2-Ma-KT exhibited a specific surface area of 1.32 (m2/g) with a pore diameter of 34.42 (nm; pore volume = 0.11 cm3/g) and was categorised as a mesoporous material. The adsorption equilibrium studies revealed that the adsorption of BG dye by Cs/Bz2-Ma-KT happens in a monolayer fashion (best compatibility with the Langmuir isotherm model; R2 = 0.93), while the adsorption process mainly occurs through chemisorption (better compatibility with the PPSO kinetic model). Furthermore, the maximum monolayer adsorption capacity of Cs/Bz2-Ma-KT was found to be 289.2 mg/g, exhibiting a great potential to be employed for the removal of BG dye from effluents. Moreover, the thermodynamic parameters revealed the spontaneity and feasibility of the adsorption process due to the negative values of ΔG, whereas the positive ΔH value signified the endothermic nature of the adsorption process.

Efficient dye removal and antibacterial activity of imidazole-crosslinked chitosan hydrogel for wastewater treatment

In this study, an imidazole cross-linked chitosan hydrogel (I/CS-4) was synthesized through the Debus-Radziszewski reaction, resulting in a multifunctional adsorbent with both dye adsorption and antimicrobial capabilities. I/CS-4 effectively removed orange G (OG) and metanil yellow (MY) dyes under various environmental conditions, including pH, initial concentration, temperature, and contact time. The hydrogel demonstrated high stability and efficiency over a broad pH range (2-10), attributed to its abundant amino and imidazole groups, which facilitate electrostatic, hydrogen bonding, and π-π stacking interactions. The maximum adsorption capacities for OG and MY were 565.00 mg/g and 490.20 mg/g, respectively, following the Langmuir isotherm and pseudo-second-order kinetic models. Additionally, I/CS-4 showed excellent recyclability, maintaining over 80 % removal efficiency after five cycles. It also exhibited potent antibacterial activity against E. coli and S. aureus while being biocompatible. These results highlight I/CS-4's potential as an effective material for treating dye-containing wastewater, combining efficient contaminant removal with microbial inhibition.

Synthesis of honeycomb-like citric acid-crosslinked chitosan hydrogel beads (cCHBs): Insight into structural characteristics of Cu(II)-loaded cCHBs (cCHBs-Cu(II))

To date, it has been regarded as one of the most challenging issues to construct novel adsorbents possessing excellent adsorption performance toward heavy metals including copper ions (Cu(II)). Especially, it is controversy about the structural characteristics of chitosan-based adsorbents adsorbed with Cu(II) ions, which could function as new adsorbents. In this study, we adopt a freeze-drying process to synthesize honeycomb-like chitosan hydrogel beads crosslinked with citric acid (cCHBs), further characterize the microstructures of cCHBs and eventually reveal the thermodynamics equations for the removal of target Cu(II). The results show that (1) the tricarboxylic groups within citric acid could prompt to construct long-range ordered channels of cCHBs under a freeze-drying process; (2) the maximum adsorption capacity of cCHBs for Cu(II) was 195.3 mg g-1 calculated by a Langmuir model; (3) the adsorption process of Cu(II) onto cCHBs was a spontaneous, endothermic, and entropy-increasing process. Moreover, the structural characteristics for honeycomb-like cCHBs adsorbed with Cu(II) (cCHBs-Cu(II)) as new adsorbents have been revealed with the adsorption of phosphate anions, which were further simulated with density functional theory (DFT). Accordingly, the superior adsorption performance of cCHBs and cCHBs-Cu(II) sheds light on a significant candidate for selective separation of a series of oxyanions.

Adsorption Characteristics of Organic Pollutants on Montmorillonites Modified by Quaternary Ammonium Surfactants with Organic Counterions

Na-montmorillonite (Na-Mt) modified by quaternary ammonium surfactants containing different organic counterions [OMt-QAS·Y-, Y = CH3CO3 -, CH3 (CH2)3COO-, CH3CH(OH)COO-, and HCOO-] was prepared for enhancing the adsorption capacity of 2, 4-dichlorophenol/cibacron brilliant yellow 3G-P. Compared with Na-Mt, whose adsorption efficiency for 2,4-dichlorophenol/cibacron brilliant yellow 3G-P was only 58/1.85 mg/g, the adsorption efficiency of OMt-QAS·Y- was greatly improved, with OMt-QAS·CH3CO3 - having the highest adsorption capacity of 152.85/116.17 mg/g. The kinetic and isotherm studies indicate that all adsorption processes fit well to the pseudo-second-order model and Freundlich model, respectively. The hydrophobicity of counterions and their affinity with the aliphatic chains had an effect on the interlayer spacing and point of zero charge of OMt-QAS·Y-, which in turn affected their adsorption properties.

Core-shell gelatin-chitosan nanoparticles with lysozyme responsiveness formed via pH-drive and transglutaminase cross-linking

Lysozyme-responsive nanoparticles were fabricated using a hydrophilic protein (gelatin type A) as the core and a hydrophobic polysaccharide (chitosan) as the shell. In this study, curcumin was used as a model molecule for encapsulation and promoted the aggregation of gelatin nanoparticles. Transglutaminase catalyzed both intra-molecular cross-linking within gelatin and inter-molecular cross-linking between gelatin and chitosan. The formation mechanism of gelatin nanoparticles was investigated by molecular docking simulations, circular dichroism spectroscopy, UV-vis spectroscopy, turbidity analysis, and dynamic light scattering. Results indicated that pH-driven processes can induce molecular conformational changes of gelatin. However, these alone are insufficient to induce nanoparticle formation. Hydrogen bonding, Pi-alkyl interactions, Pi-Pi interactions, and van der Waals forces between gelatin and curcumin are crucial for the core formation. The coating mechanism of chitosan involved covalent bonds catalyzed by transglutaminase and electrostatic interactions, verified by dynamic light scattering and Fourier transform infrared spectroscopy. Physicochemical properties characterization revealed that the core-shell nanoparticles exhibited a maximum encapsulation efficiency of 97.2 ± 0.3 % and an average particle size of 120 ± 21 nm. The core-shell nanoparticles exhibited high thermal and pH stability, with curcumin retention rates exceeding 80 % under acidic, neutral, and weakly alkaline conditions, and detained thermal degradation up to 90 °C. Additionally, lysozyme responsiveness was evaluated by controlled curcumin release with varying lysozyme concentrations, through which enzymatic hydrolysis of chitosan by lysozyme triggered an increased release rate. In summary, core-shell nanoparticles synthesized from gelatin and chitosan may be effective target delivery systems for curcumin.

Use of polysulfone capsules impregnated with phosphonium-based ionic liquid for removal of black reactive dye

In this study, polysulfone capsules impregnated with the ionic liquid tetradecyltrihexylphosphonium decanoate (IC) were synthesized and applied to remove the reactive dye black (RB) an aqueous solution. The impregnated capsules were characterized by scanning electron microscopy (SEM), surface analysis by Brunauer-Emmett-Teller (BET), Fourier transform infrared spectroscopy (FT-IR), and thermogravimetric analysis (TGA). Some adsorption parameters were investigated, such as the effect of adsorbent dosage (0.01-1.5 g/30 mL), pH (2-12), and temperature (293-323 K). At pH 8, the dye was completely removed and the process was characterized as exothermic. The kinetic model that best represented the adsorption of RB was the pseudo-first-order. The analysis of the variation of the dye concentration (150-1000 mg L-1) was performed and the Langmuir, Freundlich, and Redlich-Peterson models were presented in their nonlinear form. The maximum adsorption capacity identified by the Langmuir model was q max of 276.94 mg g-1, and the capsules could be reused for up to 4 cycles, showing removal percentages above 50% and cumulative loading of 520.8 mg g-1. In addition, a fixed bed column adsorption study was carried out. These results indicate that the proposed material has a high adsorptive capacity and has potential for application in the treatment of industrial textile effluents containing reactive dyes. In addition to considerably reducing the toxic effects of the dye on Lactuca sativa, when compared with pure IL.

Magnetic iron oxides nanocomposites: synthetic techniques and environmental applications for wastewater treatment

Nanomaterials are an emerging class of compounds with potential to advance technology for wastewater treatment. There are many toxic substances in industrial wastewater that are dangerous to the aquatic ecosystem and public health. These pollutants require the development of novel techniques to remove them from the environment. Iron oxide nanoparticles are being studied and develop as new technology to address the problem of environmental pollution due to their unique properties and effectiveness against different kind of pollutants. A variety of modified iron oxide nanoparticles have been developed through extensive research that mitigates the shortcomings of aggregation or oxidation and enhances their efficiency as novel remediator against environmental pollutants. In this review, we present synthetic approaches used for the preparation of iron oxide nanoparticles and their corresponding nanocomposites, along with the processes in which the materials are used as adsorbent/photocatalysts for environmental remediation. Applications explored includes adsorption of dyes, photocatalytic degradation of dyes, and adsorption of heavy metal ions. The use of iron oxides nanocomposite in real wastewater samples and recyclability of adsorbents and photocatalysts were also explored.

Design and evaluation of fluorescent chitosan-starch hydrogel for drug delivery and sensing applications

Composite bio-based hydrogels have been obtaining a significant attention in recent years as one of the most promising drug delivery systems. In the present study, the preparation of composite chitosan-starch hydrogel using maleic acid as a cross-linker was optimized with the help of response surface methodology. The synthesized hydrogel was fluorescent owing to clustering of large number of functional groups. Different analytical techniques, including XRD, FTIR, SEM, XPS, fluorescence and BET were utilized to characterize the prepared hydrogel. XRD analysis confirmed the formation of non-crystalline hydrogel with random arrangement of macromolecular chains. The composite hydrogel exhibited good swelling percentage with pH sensitivity, hemocompatibility and degradability. BET analysis confirmed that the variation in concentration of crosslinker significantly influences the pore volume of the hydrogel. The synthesized composite chitosan-starch hydrogel was utilized as a prospective candidate for controlling drug release. Cefixime as a model drug was loaded onto the synthesized hydrogel utilizing the swelling diffusion method. SEM micrographs showed uniform distribution of drug molecules in the drug loaded hydrogel. In vitro drug release experiments indicated the swelling dependent drug release behaviour of chitosan-starch hydrogel with higher drug release at pH 7.4 (93.08 %) compared to pH 1.2 (67.85 %). The composite chitosan-starch hydrogel was able to prolong and control the drug release up to 12 h. The drug release from the hydrogel followed Korsmeyer-Peppas and Makoid-Banakar model with Fickian diffusion mechanism. Further, the composite hydrogel displayed excitation dependent fluorescence emission with most intense blue emission band at 425 nm with an excitation wavelength of 350 nm. The inclusion of cefixime drug in the hydrogel matrix significantly reduced the fluorescence intensity; the decrease was linearly correlated to the concentration of the drug. Moreover, the fluorescence emission the chitosan-starch hydrogel was found to be dependent upon pH. The synthesized hydrogel is expected to be a potential candidate for controlled drug release as well as for fluorescent sensing applications.

Progress in the Sustainable Development of Biobased (Nano)materials for Application in Water Treatment Technologies

Water pollution remains a widespread problem, affecting the health and wellbeing of people around the globe. While current advancements in wastewater treatment and desalination show promise, there are still challenges that need to be overcome to make these technologies commercially viable. Nanotechnology plays a pivotal role in water purification and desalination processes today. However, the release of nanoparticles (NPs) into the environment without proper safeguards can lead to both physical and chemical toxicity. Moreover, many methods of NP synthesis are expensive and not environmentally sustainable. The utilization of biomass as a source for the production of NPs has the potential to mitigate issues pertaining to cost, sustainability, and pollution. The utilization of biobased nanomaterials (bio-NMs) sourced from biomass has garnered attention in the field of water purification due to their cost-effectiveness, biocompatibility, and biodegradability. Several research studies have been conducted to efficiently produce NPs (both inorganic and organic) from biomass for applications in wastewater treatment. Biosynthesized materials such as zinc oxide NPs, phytogenic magnetic NPs, biopolymer-coated metal NPs, cellulose nanocrystals, and silver NPs, among others, have demonstrated efficacy in enhancing the process of water purification. The utilization of environmentally friendly NPs presents a viable option for enhancing the efficiency and sustainability of water pollution eradication. The present review delves into the topic of biomass, its origins, and the methods by which it can be transformed into NPs utilizing an environmentally sustainable approach. The present study will examine the utilization of greener NPs in contemporary wastewater and desalination technologies.

Bacterial cellulose microfilament biochar-architectured chitosan/polyethyleneimine beads for enhanced tetracycline and metronidazole adsorption

This study investigates the potential applications of incorporating 2D bacterial cellulose microfibers (BCM) biochar into chitosan/polyethyleneimine beads as a semi-natural sorbent for the efficient removal of tetracycline (TET) and metronidazole (MET) antibiotics. Batch adsorption experiments and characterization techniques evaluate removal performance and synthesized adsorbent properties. The adsorbent eliminated 99.13 % and 90 % of TET and MET at a 10 mg.L-1 concentration with optimal pH values of 8 and 6, respectively, for 90 min. Under optimum conditions and a 400 mg.L-1 concentration, MET and TET have possessed the maximum adsorption capacities of 691.325 and 960.778 mg.g-1, respectively. According to the isothermal analysis, the adsorption of TET fundamentally follows the Temkin (R2 = 0.997), Redlich-Peterson (R2 = 0.996), and Langmuir (R2 = 0.996) models. In contrast, the MET adsorption can be described by the Langmuir (R2 = 0.997), and Toth (R2 = 0.991) models. The pseudo-second-order (R2 = 0.998, 0.992) and Avrami (R2 = 0.999, 0.999) kinetic models were well-fitted with the kinetic results for MET and TET respectively. Diffusion models recommend that pore, liquid-film, and intraparticle diffusion govern the rate of the adsorption process. The developed semi-natural sorbent demonstrated exceptional adsorption capacity over eleven cycles due to its porous bead structure, making it a potential candidate for wastewater remediation.

Poly (ionic liquid) cross-linked hydrogel encapsulated with AuPt nanozymes for the smartphone-based colorimetric detection of zearalenone

A poly (ionic liquid) enhanced poly(acrylamide-acrylic acid) (PIL-PAM/AA) hydrogel-based colorimetric sensor was designed to detect zearalenone (ZEN). Different AuxPty nanoparticles were synthesized via the on-pot method. Through the kinetic analysis and the theoretical calculation, Au0.4Pt0.6 possessed the relatively low energy barriers to adsorb and decompose H2O2 so that it exhibited relatively better catalytic activity (Km = 2.02 × 10-3, Vmax = 6.14 × 10-7). AuPt nanoparticles were encapsulated into PIL-PAM/AA hydrogel via the interaction between aptamer and cDNA. In the presence of ZEN, the embedded AuPt nanoparticles were released to complete the catalytic reaction. Coupled with the smartphone application, the established method provided the linear range of 1-250 ng mL-1, with a detection limit of 0.6979 ng mL-1 for ZEN. Meanwhile, it also possessed excellent selectivity and good anti-interference performance. In wheat and corn samples, spiked recoveries were ranging from 75% to 113.30%.

One-step hydrothermal synthesis of CeVO4/bentonite nanocomposite as a dual-functional photocatalytic adsorbent for the removal of methylene blue from aqueous solutions

Cerium vanadate/modified bentonite (CeVO4/mbt) nanocomposite with different composition percentages was synthesized through a simple one-step hydrothermal method at 180 ℃, and then its photocatalytic activity was evaluated by decolorizing methylene blue (MB) in an aqueous solution under light exposure. In order to increase the surface area as an important parameter in photocatalytic processes, bentonite was modified by ball mill method. The structural and optical properties of the synthesized composites were determined by XRD, FT-IR, DRS, FESEM, EDS, and BET measurements. XRD and EDS results confirmed the successful synthesis of pure CeVO4. FESEM images and EDS mapping showed a proper distribution of rice-like CeVO4 nanoparticles on bentonite. The removal efficiency of MB with only 0.1 g of CeVO4/mbt nanocomposite in 15 min was about 99%, which is significant compared to neat bentonite and pure CeVO4 with efficiency of 30% and 57%. The mentioned nanocomposite followed the first-order kinetics, had a reaction rate constant equal to 0.1483 min-1, and showed acceptable stability in five consecutive cycles.

Adsorptive removal of heavy metals from aqueous solutions: Progress of adsorbents development and their effectiveness

Increased levels of heavy metals (HMs) in aquatic environments poses serious health and ecological concerns. Hence, several approaches have been proposed to eliminate/reduce the levels of HMs before the discharge/reuse of HMs-contaminated waters. Adsorption is one of the most attractive processes for water decontamination; however, the efficiency of this process greatly depends on the choice of adsorbent. Therefore, the key aim of this article is to review the progress in the development and application of different classes of conventional and emerging adsorbents for the abatement of HMs from contaminated waters. Adsorbents that are based on activated carbon, natural materials, microbial, clay minerals, layered double hydroxides (LDHs), nano-zerovalent iron (nZVI), graphene, carbon nanotubes (CNTs), metal organic frameworks (MOFs), and zeolitic imidazolate frameworks (ZIFs) are critically reviewed, with more emphasis on the last four adsorbents and their nanocomposites since they have the potential to significantly boost the HMs removal efficiency from contaminated waters. Furthermore, the optimal process conditions to achieve efficient performance are discussed. Additionally, adsorption isotherm, kinetics, thermodynamics, mechanisms, and effects of varying adsorption process parameters have been introduced. Moreover, heavy metal removal driven by other processes such as oxidation, reduction, and precipitation that might concurrently occur in parallel with adsorption have been reviewed. The application of adsorption for the treatment of real wastewater has been also reviewed. Finally, challenges, limitations and potential areas for improvements in the adsorptive removal of HMs from contaminated waters are identified and discussed. Thus, this article serves as a comprehensive reference for the recent developments in the field of adsorptive removal of heavy metals from wastewater. The proposed future research work at the end of this review could help in addressing some of the key limitations facing this technology, and create a platform for boosting the efficiency of the adsorptive removal of heavy metals.

Polyethylene glycol crosslinked modified chitosan/halloysite nanotube composite aerogel microspheres for efficient adsorption of melanoidin

Melanoidins are widely present in molasses wastewater and are dark-colored macromolecules that are hazardous to the environment. Currently, adsorption methods can effectively remove melanoidins from wastewater. However, existing adsorbents have shown unsatisfactory removal efficiency for melanoidins, making practical application challenging. Polyethylene glycol crosslinked modified chitosan/halloysite nanotube composite aerogel microspheres (PCAM@HNTs) were developed as a highly efficient adsorbent for melanoidins. The removal rate of PCAM@HNTs for melanoidins was 98.53 % at adsorbent dosage 0.4 mg/mL, pH 7, temperature 303 K and 450 mg/L initial melanoidins concentration, and the corresponding equilibrium adsorption capacity was 1108.49 mg/g. The analysis results indicate that the adsorption of melanoidins by PCAM@HNTs is a spontaneous and endothermic process. It fits well with pseudo-second-order kinetic models and the Freundlich isotherm equation. The adsorption of PCAM@HNT on melanoidins is primarily attributed to electrostatic and hydrogen bonding interactions. Furthermore, PCAM@HNTs exhibit excellent biocompatibility and are nonhazardous. Therefore, PCAM@HNTs proved to be an ideal adsorbent for the decolorization of molasses wastewater.

Enhanced dye sequestration with natural polysaccharides-based hydrogels: A review

Due to the expansion of industrial activities, the concentration of dyes in water has been increasing. The dire need to remove these pollutants from water has been heavily discussed. This study focuses on the reproducible and sustainable solution for wastewater treatment and dye annihilation challenges. Adsorption has been rated the most practical way of the several decolorization procedures due to its minimal initial investment, convenient utility, and high-performance caliber. Hydrogels, which are three-dimensional polymer networks, are notable because of their potential to regenerate, biodegrade, absorb bulky amounts of water, respond to stimuli, and have unique morphologies. Natural polysaccharide hydrogels are chosen over synthetic ones because they are robust, bioresorbable, non-toxic, and cheaply accessible. This study has covered six biopolymers, including chitosan, cellulose, pectin, sodium alginate, guar gum, and starch, consisting of their chemical architecture, origins, characteristics, and uses. The next part describes these polysaccharide-based hydrogels, including their manufacturing techniques, chemical alterations, and adsorption effectiveness. It is deeply evaluated how size and shape affect the adsorption rate, which has not been addressed in any prior research. To assist the readers in identifying areas for further research in this subject, limitations of these hydrogels and future views are provided in the conclusion.

Benzopyrene elimination from the environment using graphitic carbon nitride-SnS nanocomposites

Benzopyrene (BaP) stands as a potent polycyclic aromatic hydrocarbon (PAH) molecule, boasting five fused aromatic rings, making its way into the human food chain through soil contamination. The persistent environmental presence of PAHs in soil, attributed to industrial exposure, is primarily due to their low molecular weight and hydrophobic nature. To preemptively address the entry of BaP into the food chain, the application of nanocomposites was identified as an effective remediation strategy. Post-synthesis, comprehensive characterization tests employing techniques such as UV-DRS, XRD, SEM-EDX, FTIR, and DLS unveiled the distinctive features of the g-C3N4-SnS nanocomposites. These nanocomposites exhibited spherical shapes embedded on layers of nanosheets, boasting particle diameters measuring 88.9 nm. Subsequent tests were conducted to assess the efficacy of eliminating benzopyrene from a combination of PAH molecules and g-C3N4-SnS nanocomposites. Varied parameters, including PAH concentration, adsorbent dosage, and suspension pH, were systematically explored. The optimized conditions for the efficient removal of BaP utilizing the g-C3N4-SnS nanocomposite involved 2 μg/mL of benzopyrene, 10 μg/mL of the nanocomposite, and a pH of 5, considering UV light as the irradiation source. The investigation into the mechanism governing BaP elimination closely aligned with batch adsorption results involved a thorough exploration of adsorption kinetics and isotherms. Photocatalytic degradation of benzopyrene was achieved, reaching a maximum of 86 % in 4 h and 36 % in 2 h, with g-C3N4-SnS nanocomposite acting as the catalyst. Further validation through HPLC data confirmed the successful removal of BaP from the soil matrix.

High adsorptive performance of chitosan-microalgae-carbon-doped TiO2 (kronos)/ salicylaldehyde for brilliant green dye adsorption: Optimization and mechanistic approach

A composite of chitosan biopolymer with microalgae and commercial carbon-doped titanium dioxide (kronos) was modified by grafting an aromatic aldehyde (salicylaldehyde) in a hydrothermal process for the removal of brilliant green (BG) dye. The resulting Schiff's base Chitosan-Microalgae-TiO2 kronos/Salicylaldehyde (CsMaTk/S) material was characterised using various analytical methods (conclusive of physical properties using BET surface analysis method, elemental analysis, FTIR, SEM-EDX, XRD, XPS and point of zero charge). Box Behnken Design was utilised for the optimisation of the three input variables, i.e., adsorbent dose, pH of the media and contact time. The optimum conditions appointed by the optimisation process were further affirmed by the desirability test and employed in the equilibrium studies in batch mode and the results exhibited a better fit towards the pseudo-second-order kinetic model as well as Freundlich and Langmuir isotherm models, with a maximum adsorption capacity of 957.0 mg/g. Furthermore, the reusability study displayed the adsorptive performance of CsMaTk/S remains effective throughout five adsorption cycles. The possible interactions between the dye molecules and the surface of the adsorbent were derived based on the analyses performed and the electrostatic attractions, H-bonding, Yoshida-H bonding, π-π and n-π interactions are concluded to be the responsible forces in this adsorption process.

Rapid and convenient synthesis of "green" ammonium-modified chitosan composite sponge with the existence of ascorbic acid for highly efficient removal of Congo red (CR)

In this study, a new green composite sponge made of chitosan and modified with ammonium ascorbate (ACS-CIT) was synthesized in just 10 min. Compared with CS-CIT (sponge prepared from acetic acid), ACS-CIT exhibits significantly enhanced adsorption performance for CR, with the saturated adsorption capacities increased from 353.667 to 1261.639 mg·g-1. The adsorption mechanism can be summarized as the generation of more hydrogen bonds, electrostatic attraction, and intra particle diffusion, revealing the addition of ascorbic acid introduced more hydroxyl groups, thereby enhancing the hydrogen bonding force, and the ammonium modification of chitosan improved the electrostatic attraction of the material, resulting in a significant increase in its adsorption capacity. Additionally, the prepared ACS-CIT showed excellent CR removal performance even in the presence of multiple interfering factors coexisting in the simulated wastewater, and the adsorption capacity remained stable after at least five cycles. Furthermore, the maximum bed capacity of ACS-CIT for CR is 1152.829 mg·g-1 under the given conditions of a flow rate of 1 mL·min-1, inlet concentration of 150 mg·L-1, a bed height of 1 cm respectively, and the breakthrough curve followed the Thomas model. The results indicated the eco-friendly and recyclable ACS-CIT is a promising adsorbent for CR dye removal in water.

Anti-proliferative, Morphological and Molecular Docking Studies of New Thiophene Derivatives and their Strategy in Ionic Liquids Immobilized Reactions

BACKGROUND

A number of research were conducted on the pyran and thiophene derivatives, which were attributed to have a wide range of biological activities, including anti-plasmodial, as well as acting as caspase, hepatitis C and cancer inhibitors.

OBJECTIVE

The multicomponent reactions of the 5-acetyl-2-amino-4-(phenylamino)-thiophene-3-carbonitrile produced biologically active target molecules like pyran and their fused derivatives. Comparison between regular catalytic multi-component reactions and solvent-free ionic liquids immobilized multicomponent was studied.

METHODS

The multicomponent reactions in this work were carried out not only under the reflux conditions using triethylamine as a catalyst but also in solvent-free ionic liquids immobilized magnetic nanoparticles (MNPs) catalysts.

RESULTS

Through this work, thirty-one new compounds were synthesized and characterized and were evaluated toward the six cancer cell lines, namely A549, HT-29, MKN-45, U87MG, and SMMC-7721 and H460. The most active compounds were further screened toward seventeen cancer cell lines classified according to the disease. In addition, the effect of compound 11e on the A549 cell line was selected to make further morphological changes in the cell line. The Molecular docking studies of 11e and 11f were carried and promising results were obtained.

CONCLUSION

The synthesis of heterocyclic compounds derived from thiophene derivatives has been receiving significant attention. After a detailed optimizing study, it has been found that the solvent-free ionic liquids immobilized multi-component syntheses afforded a high yield of compounds, opening a greener procedure for this synthetically relevant transformation. Many of the synthesized compounds can be considered anticancer agents, enhancing further studies.

Synthesis of salicylaldehyde tailored PAMAM dendrimers/chitosan for adsorption of aqueous Hg(II): Performance and mechanism

Water pollution caused by Hg(II) exerts hazardous effect to environmental safety and human health. Herein, a family of salicylaldehyde tailored poly(amidoamine) (PAMAM) dendrimers/chitosan composites (G0-S/CTS, G1-S/CTS, and G2-S/CTS) were prepared and used for the removal of Hg(II) from water solution. The adsorption performance of the as-prepared composites for Hg(II) was thoroughly demonstrated by determining various influencing factors. G0-S/CTS, G1-S/CTS and G2-S/CTS exhibited competitive adsorption capacity and good adsorption selective property for Hg(II). The maximum adsorption capacity of G0-S/CTS, G1-S/CTS and G2-S/CTS for Hg(II) were 1.86, 2.18 and 4.47 mmol‧g-1, respectively. The adsorption for Hg(II) could be enhanced by raising initial Hg(II) concentration and temperature. The adsorption process was dominated by film diffusion processes with monolayer adsorption behavior. The functional groups of NH2, CONH, CN, OH, CO and CN were mainly responsible for the adsorption of Hg(II). G0-S/CTS, G1-S/CTS and G2-S/CTS displayed good regeneration property and the regenerate rate maintained 95.00 % after five adsorption-desorption cycles. The as-prepared adsorbents could be potentially used for the efficient removal of Hg(II) from aqueous solution.

Biogenic preparation of copper oxide nanoparticles using table olive: Catalytic reduction, cytotoxicity, and burn wound healing activities

Green strategy for the preparation of copper oxide nanoparticles (CuO NPs) using table olive has been researched in the present work. Some characterization assays viz., transmission electron microscopy (TEM), X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) was used for evaluation of the crystal structure, size and morphology of the manufactured NPs. As a catalyst, the prepared material demonstrated remarkable catalytic capability (>99% in 4 min) for the reduction of rhodamine B using sodium borohydride. In addition, the treated cells with the CuO NPs were examined by regarding the cytotoxicity properties on normal (HUVEC) cell line. The results showed that the prepared CuO NPs did not have any cytotoxicity effects on HUVEC (up to 500 μg/mL). Furthermore, in vivo experiments on burn wounds in rats show that the synthesized CuO NPs ointment significantly diminished (p ≤ 0.01) the wound area. On the other hand, the wound contracture factor was increased in comparison with the control groups. Collectively, the CuO NPs prepared by biological method have potential applications in organic pollutants reduction and wound care applications. In this viewpoint, CuO NPs may be considered as an effective for treatment of different wounds including burn wounds or injuries from surgeries such as plastic surgery.

Hybrid chitosan/molecularly imprinted polymer hydrogel beads doped with iron for selective ibuprofen adsorption

Pharmaceutical pollutants are a group of emerging contaminants frequently found in water streams. In this study, the composite chitosan beads with incorporated molecularly imprinted polymers (monoliths or microparticles) and iron(III) hydroxide were fabricated to remove ibuprofen from aqueous solutions. The adsorptive properties were investigated in different conditions to evaluate the influence of solution pH, adsorbent dose, ibuprofen initial concentration, adsorption time, and temperature. The highest adsorption capacity (79.41 mg g-1), about twice as large as that for the chitosan beads without polymers (39.42 mg g-1), was obtained for the ones containing monoliths imprinted with ibuprofen. The theoretical maximum adsorption capacity of 103.93 mg g-1 was obtained based on the experiments in optimal pH 5. The adsorption of ibuprofen on the hybrid hydrogel beads followed the Freundlich isotherm and pseudo-second-order kinetic models. The process was found as endothermic and thermodynamically spontaneous. The adsorbent with a molecularly imprinted polymer retained its selectivity in the presence of other molecules. The imprinted cavities, chitosan functional groups, and iron hydroxide were presumably responsible for interactions with ibuprofen molecules. Additionally, the effectiveness of the adsorbent did not change significantly in real water samples and remained at a satisfactory level for up to four desorption-adsorption cycles.

A three-dimensional composite film-modified electrode based on polyoxometalates and ionic liquid-decorated carbon nanotubes for the determination of L-tyrosine in food

A stable and innovative composite film-modified electrode based on Dawson polyoxometalates H8P2Mo16V2O62 (P2Mo16V2) and ionic liquid (BMIMBr)-decorated carbon nanotubes, annotated as PEI/(P2Mo16V2/BMIMBr-CNTs)8, has been constructed by using the layer-by-layer self-assembly (LBL) method for the determination of L-tyrosine. The combination of three active components not only offers higher conductivity to facilitate rapid electron transfer, but also avoids the accumulation of P2Mo16V2 to expand the contact area and increase the reactive active sites. The modified electrode exhibits outstanding sensing performance for determination of Tyr with wide linear determination range of 5.8×10-7 M ~ 1.2×10-4 M, low determination limit of 1.7×10-7M (S/N=3), high selectivity for common interferences, and excellent stability at the potential of +0.78 V (vs. Ag/AgCl (3 M KCl)). The relative standard deviation (RSD) of 4.3% for five groups of parallel experiments shows the satisfactory repeatability of PEI/(P2Mo16V2/BMIMBr-CNTs)8. In addition, for determination of Tyr, the PEI/(P2Mo16V2/BMIMBr-CNTs)8 shows good recoveries of 98.8-99.8% in meat floss, which can be feasible in practical application.

Polymeric hydrogels-based materials for wastewater treatment

Low-cost and reliable wastewater treatment is a relevant issue worldwide to reduce the concentration of environmental pollutants. Industrial effluents containing dyes, heavy metals, and other inorganic and organic compounds can pollute water resources; therefore, novel technologies are required to mitigate and control their release into the environment. Adsorption is one of the simplest methods for treating contaminated water in which a wide spectrum of adsorbents can be used to remove emerging compounds. Hydrogels are interesting materials with high adsorption capacities that can be synthesized via green routes. These adsorbents are promising for large-scale industrial wastewater treatment applications; however, gaps still exist in achieving sustainable commercial implementation. This review focuses on the discussion and analysis of preparation, characterization, and adsorption properties of hydrogels for water purification. The advantages of these polymeric materials for water treatment were analyzed, including their performance in the removal of different organic and inorganic contaminants. Recent advances in the functionalization of hydrogels and the synthesis of novel composites have also been described. The adsorption capacities of hydrogel-based adsorbents are higher than 500 mg/g for different organic and inorganic pollutants, and can reach values of up to >2000 mg/g for organic compounds, significantly outperforming other materials reported for water cleaning. The main interactions involved in the adsorption of water pollutants using hydrogel-based adsorbents were described and explained to allow the interpretation of their removal mechanisms. The current challenges in the implementation of hydrogels for water purification in real-life operations are also highlighted. This review provides an updated picture of hydrogels as interesting materials to address water depollution worldwide.

Adsorption of chloroquine, propranolol, and metformin in aqueous solutions using magnetic graphene oxide nanocomposite

The work proposes the application of a nanocomposite formed by graphene oxide and magnetite to remove chloroquine, propranolol, and metformin from water. Tests related to adsorption kinetics, equilibrium isotherms and adsorbent reuse were studied, and optimization parameters related to the initial pH of the solution and the adsorbent dosage were defined. For all pharmaceuticals, adsorption tests indicated that removal efficiency was independent of initial pH at adsorbent dosages of 0.4 g L-1 for chloroquine, 1.2 g L-1 for propranolol, and 1.6 g L-1 for metformin. Adsorption equilibrium was reached within the first few minutes, and the pseudo-second-order model represented the experimental data well. While the equilibrium data fit the Sips isotherm model at 298 K, the predicted maximum adsorption capacities for chloroquine, propranolol, and metformin were 44.01, 16.82, and 12.23 mg g-1, respectively. The magnetic nanocomposite can be reused for three consecutive cycles of adsorption-desorption for all pharmaceuticals, being a promising alternative for the removal of different classes of pharmaceuticals in water.

Modeling of adsorptive removal of azithromycin from aquatic media by CoFe2O4/NiO anchored microalgae-derived nitrogen-doped porous activated carbon adsorbent and colorimetric quantifying of azithromycin in pharmaceutical products

Herein, it was aimed to optimize the removal process of Azithromycin (Azi) from the aquatic environment via CoFe2O4/NiO nanoparticles anchored onto the microalgae-derived nitrogen-doped porous activated carbon (N-PAC), besides developing a colorimetric method for the swift monitoring of Azi in pharmaceutical products. In this study, the Spirulina platensis (Sp) was used as a biomass resource for fabricating CoFe2O4/NiO@N-PAC adsorbent. The pores of N-PAC mainly entail mesoporous structures with a mean pore diameter of 21.546 nm and total cavity volume (Vtotal) of 0.033578 cm3. g-1. The adsorption studies offered that 98.5% of Azi in aqueous media could remove by CoFe2O4/NiO@N-PAC. For the cyclic stability analysis, the adsorbent was separated magnetically and assessed at the end of five adsorption-desorption cycles with a negligible decrease in adsorption. The kinetic modeling revealed that the adsorption of Azi onto the CoFe2O4/NiO@N-PAC was well-fitted to the second-order reaction kinetics, and the highest adsorption capacity was found as 2000 mg. g-1 at 25 °C based on the Langmuir adsorption isotherm model at 0.8 g. L-1 adsorbent concentration. The Freundlich isotherm model had the best agreement with the experimental data. Thermodynamic modeling indicated the spontaneous and exothermic nature of the adsorption process. Moreover, the effects of pH, temperature, and operating time were also optimized in the colorimetric Azi detection. The blue ion-pair complexes between Azi and Coomassie Brilliant Blue G-250 (CBBG-250) reagent followed Beer's law at wavelengths of 640 nm in the concentration range of 1.0 μM to 1.0 mM with a 0.94 μM limit of detection (LOD). In addition, the selectivity of Azi determination was verified in presence of various species. Furthermore, the applicability of CBBG-250 dye for quantifying Azi was evaluated in Azi capsules as real samples, which revealed the acceptable recovery percentage (98.72-101.27%). This work paves the way for engineering advanced nanomaterials for the removal and monitoring of Azi and assures the sustainability of environmental protection and public health.

Insights into Recent Advances of Biomaterials Based on Microbial Biomass and Natural Polymers for Sustainable Removal of Pharmaceuticals Residues

Pharmaceuticals are acknowledged as emerging contaminants in water resources. The concentration of pharmaceutical compounds in the environment has increased due to the rapid development of the pharmaceutical industry, the increasing use of human and veterinary drugs, and the ineffectiveness of conventional technologies to remove pharmaceutical compounds from water. The application of biomaterials derived from renewable resources in emerging pollutant removal techniques constitutes a new research direction in the field. In this context, the article reviews the literature on pharmaceutical removal from water sources using microbial biomass and natural polymers in biosorption or biodegradation processes. Microorganisms, in their active or inactive form, natural polymers and biocomposites based on inorganic materials, as well as microbial biomass immobilized or encapsulated in polymer matrix, were analyzed in this work. The review examines the benefits, limitations, and drawbacks of employing these biomaterials, as well as the prospects for future research and industrial implementation. From these points of view, current trends in the field are clearly reviewed. Finally, this study demonstrated how biocomposites made of natural polymers and microbial biomass suggest a viable adsorbent biomaterial for reducing environmental pollution that is also efficient, inexpensive, and sustainable.

Insight into the adsorptive removal of ibuprofen using porous carbonaceous materials: A review

Over the last decade, the removal of pharmaceuticals from aquatic bodies has garnered substantial attention from the scientific community. Ibuprofen (IBP), a non-steroidal anti-inflammatory drug, is released into the environment in pharmaceutical waste as well as medical, hospital, and household effluents. Adsorption technology is a highly efficient approach to reduce the IBP in the aquatic environment, particularly at low IBP concentrations. Due to the exceptional surface properties of carbonaceous materials, they are considered ideal adsorbents for the IBP removal of, with high binding capacity. Given the importance of the topic, the adsorptive removal of IBP from effluent using various carbonaceous adsorbents, including activated carbon, biochar, graphene-based materials, and carbon nanostructures, has been compiled and critically reviewed. Furthermore, the adsorption behavior, binding mechanisms, the most effective parameters, thermodynamics, and regeneration methods as well as the cost analysis were comprehensively reviewed for modified and unmodified carbonaceous adsorbents. The compiled studies on the IBP adsorption shows that the IBP uptake of some carbon-based adsorbents is significantly than that of commercial activated carbons. In the future, much attention is needed for practical utilization and upscaling of the research findings to aid the management and sustainability of water resource.

Developing nano-micro size chitosan beads using imidazolium-based ionic liquid: A perspective

The aggressive search for unique materials in recent years has put forward chitosan and modified-chitosan as materials with unique structural and morphological characteristics for various important applications. Just as imidazolium-based ionic liquids are the commonly applied ionic liquids (ILs) type for chitosan modifications for various applications, their further modifications into beads for enhancing their properties is now gaining most attention. However, most of the currently prepared imidazolium ILs modified-chitosan beads are not in nano size due to preparation difficulties. In response to this and referencing the research works in the literature, the possible breakthrough directions including synthesis routes, and physical and mechanical transformation processes are proposed. These procedures are expected to provide certain theoretical and empirical basis, as well as technical guide for developing nano-micro size chitosan beads using imidazolium based ILs.

Preparation and Characterization of di- and Tricarboxylic Acids-Modified Arabinogalactan Plasticized Composite Films

To ensure the high quality of water, it is necessary to remove toxic pollutants. At present, purification of water is implemented using various sorbents. The efficient sorption materials are modified polysaccharides. In this study, we report on a new environmentally friendly method for modifying larch hemicellulose-arabinogalactan (AG)-with polybasic carboxylic acids (citric, succinic, oxalic, and adipic) to obtain composite materials. The synthesized AG derivatives have been explored by a complex of physicochemical methods, including gel permeation chromatography (GPC), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffractometry (XRD), scanning electron microscopy (SEM), and sorption capacity investigations. It is shown that the heat treatment results in the formation of additional inter- and intramolecular bonds between carboxylic acids and polysaccharide molecules. The formation of ester bonds has been confirmed by the appearance of absorption bands in the IR spectra in the range of 1750-1690 cm^-1. It has been found, using the TGA study, that the most thermally stable (up to 190 °C) sample is arabinogalactan oxalate obtained under heat treatment. The SEM study of the synthesized AG films has shown that the modified samples have the homogeneous film surface ensured by cross-linking. It has been established, when studying the sorption properties of the AG derivatives, that AG succinate (82.52%) obtained by lyophilization has the highest sorption capacity, due to the developed mesoporous surface, which, in turn, makes the synthesized films promising eco-friendly materials for use as drug carriers, sorbents, and water treatment agents.

The MIL100(Fe)/BaTi0.85Zr0.15O3 nanocomposite with the photocatalytic capability for study of tetracycline photodegradation kinetics

The visible light-active nanocomposite with the photocatalytic capability was facile one-pot solvothermal method successfully synthesized. X-ray diffraction (XRD), Thermogravimetry and Derivative Thermogravimetry (TG-DTG), Scanning Electron Microscopy with Energy Dispersive X-ray Analysis (SEM-EDX), Diffuse Reflectance Spectroscopy (UV-Vis DRS), and Fourier Transform Infra-Red (FT-IR) analysis were employed to characterize the synthetized BaTi_0.85Zr_0.15O3, MIL-100(Fe), and the MIL-100(Fe)/BaTi_0.85Zr_0.15O₃ samples. As a result of the Scherrer equations, the size of grains for MIL-100(Fe), BaTi_0.85Zr_0.15O₃, and MIL-100(Fe)/BaTi_0.85Zr_0.15O₃ was estimated to be 40.81, 12.00, and 22.70 nm, respectively. MIL-100(Fe), BaTi_0.85Zr_0.15O₃, and MIL-100(Fe)/BaTi_0.85Zr_0.15O₃ samples showed bandgap values of 1.77, 3.02, and 2.56 determined from their absorption edge wavelengths. In the photodegraded solutions, chemical oxygen demand (COD) data and tetracycline (TC) absorbencies were used to obtain the rate constants of 0.032 min^-1 and 0.030 min^-1, respectively. This corresponds to t_1/2-values of 27.7 min and 21.7 min, respectively, for the degradation and mineralization of TC molecules during photodegradation process.

A Z-scheme CdS/Ag3PO4 catalyst: Characterization, experimental design and mechanism consideration for methylene blue

Due to the explosive use of Azo dyes in various industries such as textiles, discharging these industrial effluents into the environment critically polluted water supplies. Accordingly, constructing/developing novel binary catalysts to diminish the pollution extent of such effluents before discharging into environment is an excellent issue in environmental chemistry. Here, a binary CdS/ Ag₃PO₄ was constructed, and its boosted photocatalytic activity was proven against methylene blue (MB), as a model dye pollutant. The Wurtzite CdS and Ag₃PO₄ cubic crystal nanoparticles were synthesized and coupled mechanically. The binary sample's lowest photoluminescence (PL) results confirm a higher e/h separation. DRS results confirmed a decreased energy gap for the coupled system. The semiconductors' VB and CV potentials were calculated and used for constructing of Z-scheme mechanism. The photocatalytic activity was followed via an experimental design approach. The model F-value of 89.75 > F_0.05,14,13 = 2.42 and LOF F-value of 6.57 < F_{0.05,10, 3} = 8.79 reveal that the model well processed data. The optimal run conditions were CMB: 5 ppm, Catalyst dose: 1 g/L, pH: 3.25, and irradiation time: 139 min, at which 85% of MB molecules were degraded. Based on the trend of ascorbic acid > isopropanol > formic acid ≈ nitrate obtained for the scavengers' importance in decreasing the photocatalyst activity, superoxide radicals had the highest effect in MB degradation and then ^•OH. The results showed the direct Z-scheme has the main effect on MB degradation by the binary sample.

The effect of Fe-Zn mole ratio (2:1) bimetallic nanoparticles supported by hydroxyethyl cellulose/graphene oxide for high-efficiency removal of doxycycline

In this research, Hydroxyethyl cellulose - graphene oxide HEC-GO and HEC-GO/Fe-Zn mole ratio (2:1) nanocomposite as adsorbents were fabricated by crosslinking ethylene glycol dimethacrylate (EGDMA) to study the thermodynamic, kinetic and isotherm of doxycycline antibiotic adsorption. The morphology and structure of the adsorbents were analyzed by Fourier transform infrared spectroscopy (FT-IR), Field Emission Scanning Electron Microscopy with Energy Dispersive X-Ray Spectroscopy (FE-SEM- EDX), and Transmission electron microscopy (TEM). The adsorption behavior of doxycycline (DOX) was studied with different parameters including doxycycline concentration, pH, the dose of adsorbent (HEC-GO and HEC-GO/Fe-Zn, mole ratio (2:1)), contact time, and temperature. The optimal conditions for the removal of DOX are pH = 3.0, contact time 100 min, and 20 min for HEC-GO and HEC-GO/Fe-Zn mole ratio (2:1). The removal percentage for HEC-GO and HEC-GO/Fe-Zn mole ratio (2:1) was 97% and 95.5%, respectively. Equilibrium adsorption isotherms such as the Langmuir, Freundlich, and Temkin models were analyzed according to the experimental data. Also, four adsorption kinetics were investigated for removing DOX. The Langmuir isotherm and pseudo-second-order kinetic models provided the best fit for experimental data for HEC-GO and HEC-GO/Fe-Zn mole ratio (2:1). Thermodynamic data showed that negative values of Gibbs free energy (ΔG°) and the negative value of enthalpy (ΔH°) of the adsorption process for adsorbents. It means that DOX removal was a spontaneous and exothermic reaction.

Kinetics, isotherms, and mechanism of removing cationic and anionic dyes from aqueous solutions using chitosan/magnetite/silver nanoparticles

Modified magnetite chitosan with silver nanoparticles was synthesized and tested for removing cationic and anionic dyes in aqueous solutions. Initial dye concentration, pH, and contact time were examined. Results showed that pH (4.0) was optimal for removing anionic dyes (methyl orange) and pH 8.0 for removing cationic dyes (methylene blue). According to these results, zeta potentials were found to be 8.43 and - 39.17 mV at pH 4.0 and 8.0, respectively. So, it is attracted to positively charged cationic dyes in an alkaline medium and negatively charged anionic dyes in an acidic medium because of their opposite charges. Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS), thermal gravimetric analysis (TGA), and zeta potential measurements were used to characterize the synthesized nanosorbents. A pseudo-second-order kinetic model is fitted with the Langmuir adsorption model, with an adsorption capacity of 417 and 476 mg/g for methyl orange and methylene blue, respectively. For both dyes, modified magnetite chitosan with silver nanoparticles showed high regeneration capability and recovery for up to four cycles without adsorption efficiency loss. Furthermore, modified magnetite chitosan with silver nanoparticles, as prepared in the present study, was demonstrated to be an effective adsorbent for organic pollutants in wastewater.

A novel hydrogel beads based copper-doped Cerastoderma edule shells@Alginate biocomposite for highly fungicide sorption from aqueous medium

The engineering of a novel biocomposite based on Cerastoderma edule shells doped with copper and alginate (Ce-Cu@Alg) forming hydrogel beads was used for batch and dynamic adsorption thiabendazole (TBZ) pesticide from water. The prepared biosorbent was analyzed by various characterization techniques such as scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), Brunauer-Emmett-Teller analysis (BET), and energy dispersive spectroscopy (EDS), thermogravimetric and differential analysis (TGA-DTA). The results of the TBZ batch biosorption by Ce-Cu@Alg composite showed that the Langmuir model was the most adequate to describe the adsorption process, with a maximum adsorption capacity value of 21.98 mg/g. Moreover, the adsorption kinetics were adjusted by the pseudo-second-order model. The optimal conditions determined by the RSM approach coupled with the CCD design were 100 ppm of initial TBZ concentration, a Ce-Cu@Alg beads dose of 6 g/L and a contact time of 180 min for maximum removal of 83.42%. On the other hand, the TBZ sorption on a fixed bed of Ce-Cu@Alg beads was effective at high column height, low effluent flow and low solution concentration. The Thomas model was best fitted to the kinetic data. This study shows the possibility of using this new hybrid biocomposite in the industrial sector to treat large effluent volumes.

Continuous removal of pharmaceutical drug chloroquine and Safranin-O dye from water using agar-graphene oxide hydrogel: Selective adsorption in batch and fixed-bed experiments

In this work, Chloroquine diphosphate, and the cationic dye Safranin-O were selectively removed from water using the agar-graphene oxide (A-GO) hydrogel, produced via simple one-step jellification process. The morphology of the A-GO biocomposite was characterized and batch experiments were performed, with adsorption isotherms satisfactorily fitting (R² > 0.98) Sips (Safranin-O) and Freundlich (Chloroquine) isotherms. Driving force models and Fick's diffusion equation were applied to the modeling of kinetic data, and a satisfactory fit was obtained. Selective adsorption carried out in batch indicated that competitive adsorption occurs when both components are mixed in water solution - the adsorptive capacities dropped ∼10 mg g^-1 for each component, remaining 41 mg g^-1 for safranin-O and 31 mg g^-1 for chloroquine. Fixed-bed breakthrough curves obtained in an adsorption column showed adsorption capacities over 63 mg g^-1 and 100 mg g^-1 for chloroquine and safranin-O, respectively, also exhibiting outstanding regenerative potentials. Overall, the biocomposite produced using graphene oxide proved to be a viable and eco-friendly alternative to continuously remove both contaminants from water.

Recent advances in polymer composite, extraction, and their application for wastewater treatment: A review

Wastewater from diverse industrial sectors, agricultural practices and other household activities causes water pollution that result in different environmental issues. The main goals of wastewater treatment are typically to enhance the purity of wastewater and to enable the disposal of domestic and industrial effluents without endangering human health or causing excessive environmental issues. There were several natural and synthetic materials which have been utilized for wastewater treatment, amongst them polymers gain more importance due to their non-toxicity, economic feasibility, abundant availability of sources, renewability, biocompatibility, biodegradability, etc. The organic polymers such as cellulose, chitin, gelatin, alginates, lignin, dextran and other starch derivatives are the most commonly used natural polymers in wastewater treatments. The unique physical and chemical characteristics of the natural polymers make them become an alternative in wastewater treatments such as membrane filtration, adsorption, coagulation, flocculation and ion-exchange process to remove harmful contaminants such as toxic metals, dyes, medicines, pesticides, and so on. The review article discusses natural polymers and related uses in wastewater treatment. This review mainly focused on the wastewater treatment using natural polymers and the techniques involved for their extraction from natural sources. The recent trends in polymer extraction from the natural sources and the scope for the future research of natural polymers in various sectors are also discussed in detail.

Recent advancements in engineered biopolymeric-nanohybrids: A greener approach for adsorptive-remediation of noxious metals from aqueous matrices

Industrial wastewater is causing serious health problems due to presence of large concentrations of toxic metals. Removal of these metals is still a big challenge using pristine natural biopolymers due to their low surface area, water solubility, and poor recovery. Developing biopolymeric composites with other materials has attained attention because they possess a high surface area and structural porosity, high reactivity, and less water solubility. In simple words, biopolymeric nanohybrids have great adsorption capacity for heavy metals. Biopolymeric materials are abundant, low cost, biodegradable, and possess different functional moieties (carboxyl, amine, hydroxyl, and carbonyl) which play a vital role to adsorb metal ions through various inter-linkages (i.e., electrostatic, hydrogen bonding, ion exchange, chelation, etc.). Biopolymeric nanohybrids have been proven a potent tool in environmental remediation such as the abatement of heavy metal ions from polluted water. Herein, we have reported the adsorption potential of various biopolymers (cellulose, chitosan, pectin, gelatin, and silk proteins) for the removal of heavy metals. This review discusses the suitability of biopolymeric nanohybrids as an adsorbent for heavy metals, their synthesis, modification, adsorption potential, and adsorption mechanism along with best fitted thermodynamic and kinetic models. The influence of pH, contact time, and adsorbent dose on adsorption potential has also been discussed in detail. Lastly, the challenges, research gaps and recommendations have been presented. This review concludes that biopolymers in combination with other materials such as metal-based nanoparticles, clay, and carbon-based materials are excellent materials to remove metallic ions from wastewater. Significant adsorption of heavy metals was obtained at a moderate pH (5-6). Contact time and adsorbent dose also affect the adsorption of heavy metals in certain ways. The Pseudo-first order model fits the data for the initial period of the first step of the reaction. Kinetic studies of different adsorption processes of various biopolymeric nanohybrids described that for majority of bionanohybrids, Pseudo-second order fitted the experimental data very well. Functionalized biopolymeric nanohybrids being biodegradable, environment friendly, cost-effective materials have great potential to adsorb heavy metal ions. These may be the future materials for environmental remediation.

Innovative adsorbents based on bentonite mining waste for removal of cationic dyes from wastewater

Waste rock from bentonite mining (WRBM) was evaluated as potential adsorbents for removing crystal violet (CV) and methylene blue (MB) cationic dyes from contaminated water. The waste samples (AM01, AM02, and AM03) were collected from different locations of the bentonite mine and characterized through X-ray diffraction, X-ray fluorescence, Fourier-transform infrared spectroscopy, N₂ adsorption/desorption, and cation exchange capacity. The adsorption efficiency of CV and MB dyes was investigated through the effect of initial concentration, contact time, pH, the dosage of adsorbent, and temperature. Sample AM02 showed the largest surface area (69.13 m²/g) and the best adsorptive performance for both dyes, with removal more significant than 90%. The adsorption of CV and MB in the waste followed the Langmuir isothermal model. Samples AM01 and AM02 followed the pseudo-second-order (PSO) kinetic model, while AM03 better fitted the Elovich kinetic model. The enthalpy (ΔH), entropy (ΔS), and Gibbs energy (ΔG) were evaluated as adsorption parameters. The process of adsorption of CV and MB dyes in the waste was predominantly endothermic and occurred spontaneously. WRBM samples proved to be a promising candidate for removing cationic dyes present in water.

A censorious review on the role of natural lignocellulosic fiber waste as a low-cost adsorbent for removal of diverse textile industrial pollutants

BACKGROUND

Textile industries produce fabricated colored products using toxic dyes and other harsh chemicals. It is the responsibility of the textile industries to treat and eliminate these hazardous pollutants. However, due to the growing population demand, the treatment of these hazardous effluents is ineffective and imposes the treatment cost over the end users. The release of partially treated effluents in the environment may cause a severe threat to the ecology and its biota. The critical objective is to treat textile effluents efficiently using agricultural natural fiber waste. Generation of agricultural lignocellulosic fibrous waste increases every year due to growing population demand. Its use in the modern world is limited due to synthetic products. An alternative has enumerated to avoid wastage of fibrous resources and its clean disposal.

OBJECTIVE

The main objective of this review paper discussed the feasibility of lignocellulosic fibers and other lignocellulosic materials as natural low-cost adsorbent.

METHODS

The literature study was performed using Web of Science and Scopus indexed journals. The main factors considered to increase the adsorption ability, including the types of lignocellulosic surface modification techniques were searched with utmost importance for quality results. Intending to summarize the literature survey and provide persuasive content, systematic review process was considered for this novel article.

RESULTS

Out of 230 valuable publications, 159 published articles were considered for the present study until March 2022. The articles surplus with factors affecting adsorption (pH, adsorption dosage, surface area, temperature, initial concentration, contact time, physical and chemical properties of pollutants) and surface modification techniques (physical, chemical, and biological) were considered for this manuscript.

CONCLUSION

Overall, the physical and chemical modification methods are widely used instead of biological methods due to various factors as discussed briefly. Furthermore, the finding of this article supports the fact that the fibrous by-product resources are wasted in various occasions due to the modern lifestyle. Even though there is evidential possibility to implement the low-cost adsorbents, the industries limit their application prospects due to existing technology and financial compromises.

Fabrication of different adsorbents based on zirconium oxide, graphene oxide, and dextrin for removal of green malachite dye from aqueous solutions

In this study, graphene oxide and amine graphene were studied by binding to dextrin and zirconium oxide nanoparticles as adsorbent nanocomposites to the removal of dye. Identification and characterization of the synthesized materials were examined using FTIR, XRD, SEM, and BET analyses. Adsorption tests between adsorbents and green malachite (MG) dye solution for the synthesized nanocomposites were performed by considering parameters such as contact time, solution pH, and adsorbent dosage. The data indicated that dye removal increased with increasing the amount of adsorbent dosage. Increased dye removal by increasing the adsorbent dosage can be attributed to the increase of availability of the number of active sites. The active adsorption sites are saturated during the adsorption process, by the molecules of the adsorbate and filled over time. The results showed that the synthesized bio-composite had malachite green removal ability from aqueous media.

Separation of organic contaminant (dye) using the modified porous metal-organic framework (MIL)

Herein, the porous metal-organic framework (MIL-88B: Materials Institute Lavoisier) was synthesized and identified by FT-IR (Fourier transform infrared), SEM (Scanning Electron Microscopy), EDS (Energy Dispersive X-Ray Spectroscopy), and XRD (X-ray powder diffraction) analyses. Then MIL-88B was modified using 3-aminopropyl trimethoxy silane and presented as NH₂-MIL-88B. The synthesized materials were used to separate direct red dye 23 (DR23) as an organic contaminant from water. The effect of various important factors such as the amount of adsorbent, initial concentration of contaminants, and pH was investigated. The results showed that the modified adsorbent (NH₂-MIL-88B) had a higher adsorption capacity than the row adsorbent (MIL-88B). The amount of dye adsorption is high at lower pH values. The percentage of DR23 dye removal was complete under optimal conditions. Increasing the amount of adsorbent (0.001-0.003 g) and decreasing the pH (2.1-8.1) increases the percentage of dye removal and increasing the concentration of contaminant (50-125 mg/L) reduces the dye removal in the process. Isotherm data showed that the adsorption process followed the Langmuir model. Also, pseudo-first-order, pseudo-second-order, and intraparticle diffusion kinetic models were used to investigate the adsorption kinetics. Dye adsorption followed pseudo-second-order kinetics with correlation coefficient (0.99 <). The results showed that the modified adsorbent could be used as a suitable adsorbent with a high adsorption capacity for dye removal from water.

Engineering microbes for enhancing the degradation of environmental pollutants: A detailed review on synthetic biology

Anthropogenic activities resulted in the deposition of huge quantities of contaminants such as heavy metals, dyes, hydrocarbons, etc into an ecosystem. The serious ill effects caused by these pollutants to all living organisms forced in advancement of technology for degrading or removing these pollutants. This degrading activity is mostly depending on microorganisms owing to their ability to survive in harsh adverse conditions. Though native strains possess the capability to degrade these pollutants the development of genetic engineering and molecular biology resulted in engineering approaches that enhanced the efficiency of microbes in degrading pollutants at faster rate. Many bioinformatics tools have been developed for altering/modifying genetic content in microbes to increase their degrading potency. This review provides a detailed note on engineered microbes - their significant importance in degrading environmental contaminants and the approaches utilized for modifying microbes. The genes responsible for degrading the pollutants have been identified and modified fir increasing the potential for quick degradation. The methods for increasing the tolerance in engineered microbes have also been discussed. Thus engineered microbes prove to be effective alternate compared to native strains for degrading pollutants.

Silica-coated modified magnetic nanoparticles (Fe3O4@SiO2@(BuSO3H)3) as an efficient adsorbent for Pd2+ removal

It is crucial to fabricate cost-effective and efficient strategies for monitoring and eliminating hazardous metals in the water supplies. Among the many techniques, adsorption is one of the most powerful and facile ways for eliminating pollutants from effluents. It is also crucial to engineering high-performance low-cost adsorbents. In this regard, herein, Fe3O4@SiO2@(BuSO3H)3 as a modified core-shell magnetic silica nanoparticle embodies good selectivity to extract toxic metal ions from aquatic media. The present work investigated the removal performance of the magnetic adsorbent towards Pd2+ cation amongst the other heavy metal ions including Co2+, Pb2+, Hg2+, Cd2+, Cu2+, Zn2+ in aqueous solution. The flame atomic absorption spectrometry (FAAS) was utilized to assess the removal efficiency of the adsorbent. Several experimental parameters including elution condition, initial Pd(II) concentration, adsorbent dosage, initial pH of the solution, and contact time were explored to achieve the optimal conditions. The data of adsorption were very well with the Langmuir isotherm model, according to the adsorption isotherm mechanism experiments. In conclusion, this study lays the way for the development of novel magnetic adsorbents with high removal efficiencies for the removal of toxic metal ions from aqueous environment.

Polyol-assisted hydrothermal synthesis of Mn-doped α - Fe2O3(MFO) nanostructures: Spin disorder-induced magnetism and photocatalytic properties

Hierarchical nanostructures play an important role in environmental clean-up and sustainability applications. The magnetic and photocatalytic characteristics of flower-like Mn-doped α-Fe₂O₃ nanostructures were prepared by using a polyol-assisted hydrothermal method. Crystallite sizes are in the range of 35-42 nm, and the existence of 3D hierarchical nanostructures was observed in FESEM pictures. The optical band gap energy varies between 2.08 and 2.16 eV, while XPS examination exposes the ions' charge states and validates Mn³⁺ inclusion in the Fe³⁺ lattice. At room temperature, the addition of Mn to α-Fe₂O₃ results in a spin disorder ferromagnetism and coercivity of about 600 Oe was achieved. Methylene blue (MB) dye solution degraded by 92% when 2.5% Mn doped with α-Fe₂O₃ under visible conditions for 120 min irradiation time.