Single-Junction Organic Photovoltaic Cells with Approaching 18% Efficiency

Impact of length of branched alkyl side chains on thiazolothiazole-based small molecular acceptors in non-fullerene polymer solar cells

It has been reported that the length of branched alkyl side chains on fused-ring electron acceptors confers different impacts on properties versus solubility of BJH blends. However, because this impact on a non-fused acceptor backbone has rarely been studied, we examined the impact of molecular optimization from alkyl chain tuning based on non-fused thiazolothiazole small-molecule acceptors. The length of the side chain on the thiophene bridge was modified from 2-butyloctyl to 2-ethylhexyl, which corresponds to small molecules TTz3(C4C6) and TTz3(C2C4), respectively. Compared with the reported TTz3(C6C8) with long alkyl side chains, TTz3(C4C6) and TTz3(C2C4) exhibited stronger molecular aggregation, higher absorption coefficients, and greater redshifted UV absorption. Unexpectedly, after the alkyl chain was slightly shortened in this type of acceptor system, devices were successfully fabricated, but it was necessary to reduce the blending concentration at low rotation speeds due to the sharp decrease in the solubility of corresponding acceptor materials. Thus, the obtained unfavorable thickness and morphology of the active layer caused a decrease in Jsc and FF. As a consequence, TTz3(C4C6)- and TTz3(C2C4)-based devices showed an unsatisfactory power conversion efficiency of 6.02% and 2.71%, respectively, when donors were paired with the wide bandgap donor J71, which is inferior to that of TTz3(C6C8)-based devices (8.76%). These results indicate that it is challenging to determine the limit of the adjustable range of side chains to modify non-fused thiazolothiazole small-molecule acceptors for high-performance non-fullerene solar cells.

The Influence of Donor/Acceptor Interfaces on Organic Solar Cells Efficiency and Stability Revealed through Theoretical Calculations and Morphology Characterizations

End-groups halogenation strategies, generally refers to fluorination and chlorination, have been confirmed as simple and efficient methods to regulate the photoelectric performance of non-fullerene acceptors (NFAs), but a controversy over which one is better has existed for a long time. Here, two novel NFAs, C9N3-4F and C9N3-4Cl, featured with different end-groups were successfully synthesized and blended with two renowned donors, D18 and PM6, featured with different electron-withdrawing units. Detailed theoretical calculations and morphology characterizations of the interface structures indicate NFAs based on different end-groups possess different binding energy and miscibility with donors, which shows an obvious influence on phase-separation morphology, charge transport behavior and device performance. After verified by other three pairs of reported NFAs, a universal conclusion obtained as the devices based on D18 with fluorination-end-groups-based NFAs and PM6 with chlorination-end-groups-based NFAs generally show excellent efficiencies, high fill factors and stability. Finally, the devices based on D18: C9N3-4F and PM6: C9N3-4Cl yield outstanding efficiency of 18.53 % and 18.00 %, respectively. Suitably selecting donor and regulating donor/acceptor interface can accurately present the photoelectric conversion ability of a novel NFAs, which points out the way for further molecular design and selection for high-performance and stable organic solar cells.

Molecular Design for Vertical Phase Distribution Modulation in High-Performance Organic Solar Cells

Component distribution within the photoactive layer dictates the morphology and electronic structure and substantially influences the performance of organic solar cells (OSCs). In this study, a molecular design strategy is introduced to manipulate component and energetics distribution by adjusting side-chain polarity. Two non-fullerene acceptors (NFAs), ITIC-16F and ITIC-E, are synthesized by introducing different polar functional substituents onto the side chains of ITIC. The alterations result in different distribution tendencies in the bulk heterojunction film: ITIC-16F with intensified hydrophobicity aligns predominantly with the top surface, while ITIC-E with strong hydrophilicity gravitates toward the bottom. This divergence directly impacts the vertical distribution of the excitation energy levels, thereby influencing the excitation kinetics over extended time periods and larger spatial ranges including enhanced diffusion-mediated exciton dissociation and stimulated charge carrier transport. Benefitting from the favorable energy distribution, the device incorporating ITIC-E into the PBQx-TF:eC9-2Cl blend showcases an impressive power conversion efficiency of 19.4%. This work highlights side-chain polarity manipulation as a promising strategy for designing efficient NFA molecules and underscores the pivotal role of spatial energetics distribution in OSC performance.

Rational molecular and device design enables organic solar cells approaching 20% efficiency

For organic solar cells to be competitive, the light-absorbing molecules should simultaneously satisfy multiple key requirements, including weak-absorption charge transfer state, high dielectric constant, suitable surface energy, proper crystallinity, etc. However, the systematic design rule in molecules to achieve the abovementioned goals is rarely studied. In this work, guided by theoretical calculation, we present a rational design of non-fullerene acceptor o-BTP-eC9, with distinct photoelectric properties compared to benchmark BTP-eC9. o-BTP-eC9 based device has uplifted charge transfer state, therefore significantly reducing the energy loss by 41 meV and showing excellent power conversion efficiency of 18.7%. Moreover, the new guest acceptor o-BTP-eC9 has excellent miscibility, crystallinity, and energy level compatibility with BTP-eC9, which enables an efficiency of 19.9% (19.5% certified) in PM6:BTP-C9:o-BTP-eC9 based ternary system with enhanced operational stability.

Iodinated Electron Acceptor with Significantly Extended Exciton Diffusion Length for Efficient Organic Photovoltaic Cells

Iodination has unlocked new potentials in organic photovoltaics (OPVs). A newly designed and synthesized iodinated non-fullerene acceptor, BO-4I, showcases exceptional excitation delocalization property with the exciton diffusion length increased to 80 nm. The enhanced electron delocalization property is attributed to the larger atomic radius and electron orbit of the iodine atom, which facilitates the formation of intra-moiety excitations in the acceptor phase. This effectively circumvents the charge transfer state-related recombination mechanisms, leading to a substantial reduction in non-radiative energy loss (ΔEnr ). As a result, OPV cell based on PBDB-TF : BO-4I achieves an impressive efficiency of 18.9 % with a notable ΔEnr of 0.189 eV, markedly surpassing their fluorinated counterparts. This contribution highlights the pivotal role of iodination in reducing energy loss, thereby affirming its potential as a key strategy in the development of advanced next-generation OPV cells.

Chemically Engineered Titanium Oxide Interconnecting Layer for Multijunction Polymer Solar Cells

We report chemically tunable n-type titanium oxides using ethanolamine as a nitrogen dopant source. As the amount of ethanolamine added to the titanium oxide precursor during synthesis increases, the Fermi level of the resulting titanium oxides (ethanolamine-incorporated titanium oxides) significantly changes from -4.9 eV to -4.3 eV, and their free charge carrier densities are enhanced by two orders of magnitudes, reaching up to 5 × 1018 cm-3. Unexpectedly, a basic ethanolamine reinforces not only the n-type properties of titanium oxides, but also their basicity, which facilitates acid-base ionic junctions in contact with acidic materials. The enhanced charge carrier density and basicity of the chemically tuned titanium oxides enable multi-junction solar cells to have interconnecting junctions consisting of basic n-type titanium oxides and acidic p-type PEDOT:PSS to gain high open-circuit voltages of 1.44 V and 2.25 V from tandem and triple architectures, respectively.

An Ortho-Bisalkyloxylated Benzene-Based Fully Non-fused Electron Acceptor for Efficient Organic Photovoltaic Cells

To develop the low-cost nonfullerene acceptors (NFAs), two fully non-fused NFAs (TBT-2 and TBT-6) with ortho-bis((2-ethylhexyl)oxy)benzene unit and different side chains onto thiophene-bridges are synthesized through highly efficient synthetic procedures. Both acceptors show good planarity, low optical gaps (≈1.51 eV), and deep highest occupied molecular orbital levels (≤-5.77 eV). More importantly, the single-crystal structure of TBT-2 shows compact molecular arrangement due to the existence of intramolecular interactions between adjacent aromatic units and strong π-π stacking between intermolecular terminal groups. When the two acceptors are fabricated organic photovoltaic (OPV) cells by combining with a wide optical gap polymer donor, the TBT-6 with strong crystallization forms large domain sizes in bulk heterojunction (BHJ) blend. As a result, the TBT-6-based OPV cell shows a low power conversion efficiency (PCE) of 9.53%. In contrast, the TBT-2 with proper crystallization facilitates morphological optimization in the BHJ blend. Consequently, the TBT-2-based OPV cell gives an outstanding PCE of 13.25%, which is one of the best values among OPV cells with similar optical gaps. Overall, this work provides a practical molecular design strategy for developing high-performance and low-cost electron acceptors.

High-Efficiency Binary and Ternary Organic Solar Cells Based on Novel Nonfused-Ring Electron Acceptors

In this study, three nonfused-ring electron acceptors (2TT, 2TT-C6-F, and 2TT-C11-F) with the same steric hindrance groups (2,4,6-tripropylbenzene) are designed and synthesized and the impact of electron-withdrawing and lateral alkyl side chains on the performance of binary and ternary organic solar cells (OSCs) is explored. For the binary OSCs, 2TT-C11-F with IC-2F terminal groups and lateral undecyl side chains display a red shifted absorption spectrum and suitable energy levels, and the corresponding blend film exhibits appropriate phase separation and crystallinity. Thus, binary OSCs based on 2TT-C11-F achieve an impressive power conversion efficiency of 13.03%, much higher than the efficiencies of those based on 2TT (9.68%) and 2TT-C6-F (12.11%). In the ternary OSCs, 2TT with CC terminal groups and lateral hexyl side chains exhibit complementary absorption and cascade energy levels with a host binary system (D18:BTP-eC9-4F). Hence, the ternary OSCs based on 2TT achieve a remarkable efficiency of 19.39%, ranking among the highest reported values. The research yields comprehensive 2TT-series nonfused-ring electron acceptors, demonstrating their great potential for the fabrication of high-performance binary and ternary OSCs.

Organic Photovoltaic Stability: Understanding the Role of Engineering Exciton and Charge Carrier Dynamics from Recent Progress

Benefiting from the synergistic development of material design, device engineering, and the mechanistic understanding of device physics, the certified power conversion efficiencies (PCEs) of single-junction non-fullerene organic solar cells (OSCs) have already reached a very high value of exceeding 19%. However, in addition to PCEs, the poor stability is now a challenging obstacle for commercial applications of organic photovoltaics (OPVs). Herein, recent progress made in exploring operational mechanisms, anomalous photoelectric behaviors, and improving long-term stability in non-fullerene OSCs are highlighted from a novel and previously largely undiscussed perspective of engineering exciton and charge carrier pathways. Considering the intrinsic connection among multiple temporal-scale photocarrier dynamics, multi-length scale morphologies, and photovoltaic performance in OPVs, this review delineates and establishes a comprehensive and in-depth property-function relationship for evaluating the actual device stability. Moreover, this review has also provided some valuable photophysical insights into employing the advanced characterization techniques such as transient absorption spectroscopy and time-resolved fluorescence imagings. Finally, some of the remaining major challenges related to this topic are proposed toward the further advances of enhancing long-term operational stability in non-fullerene OSCs.

Selectively Modulating Componential Morphologies of Bulk Heterojunction Organic Solar Cells

Achieving precise control over the nanoscale morphology of bulk heterojunction films presents a significant challenge for the conventional post-treatments employed in organic solar cells (OSCs). In this study, a near-infrared photon-assisted annealing (NPA) strategy is developed for fabricating high-performance OSCs under mild processing conditions. It is revealed a top NIR light illumination, together with the bottom heating, enables the selective tuning of the molecular arrangement and assembly of narrow bandgap acceptors in polymer networks to achieve optimal morphologies, as well as the acceptor-rich top surface of active layers. The derived OSCs exhibit a remarkable power conversion efficiency (PCE) of 19.25%, representing one of the highest PCEs for the reported binary OSCs so far. Moreover, via the NPA strategy, it has succeeded in accessing top-illuminated flexible OSCs using thermolabile polyethylene terephthalate from mineral water bottles, displaying excellent mechanical stabilities. Overall, this work will hold the potential to develop organic solar cells under mild processing with various substrates.

Polymer-Entangled Spontaneous Pseudo-Planar Heterojunction for Constructing Efficient Flexible Organic Solar Cells

Flexible organic solar cells (FOSCs) have attracted considerable attention from researchers as promising portable power sources for wearable electronic devices. However, insufficient power conversion efficiency (PCE), intrinsic stretchability, and mechanical stability of FOSCs remain severe obstacles to their application. Herein, an entangled strategy is proposed for the synergistic optimization of PCE and mechanical properties of FOSCs through green sequential printing combined with polymer-induced spontaneous gradient heterojunction phase separation morphology. Impressively, the toughened-pseudo-planar heterojunction (Toughened-PPHJ) film exhibits excellent tensile properties with a crack onset strain (COS) of 11.0%, twice that of the reference bulk heterojunction (BHJ) film (5.5%), which is among the highest values reported for the state-of-the-art polymer/small molecule-based systems. Finite element simulation of stress distribution during film bending confirms that Toughened-PPHJ film can release residual stress well. Therefore, this optimal device shows a high PCE (18.16%) with enhanced (short-circuit current density) JSC and suppressed energy loss, which is a significant improvement over the conventional BHJ device (16.99%). Finally, the 1 cm2 flexible Toughened-PPHJ device retains more than 92% of its initial PCE (13.3%) after 1000 bending cycles. This work provides a feasible guiding idea for future flexible portable power supplies.

Unraveling the Structure-Property-Performance Relationships of Fused-Ring Nonfullerene Acceptors: Toward a C-Shaped ortho-Benzodipyrrole-Based Acceptor for Highly Efficient Organic Photovoltaics

The high-performance Y6-based nonfullerene acceptors (NFAs) feature a C-shaped A-DA'D-A-type molecular architecture with a central electron-deficient thiadiazole (Tz) A' unit. In this work, we designed and synthesized a new A-D-A-type NFA, termed CB16, having a C-shaped ortho-benzodipyrrole-based skeleton of Y6 but with the Tz unit eliminated. When processed with nonhalogenated xylene without using any additives, the binary PM6:CB16 devices display a remarkable power conversion efficiency (PCE) of 18.32% with a high open-circuit voltage (Voc) of 0.92 V, surpassing the performance of the corresponding Y6-based devices. In contrast, similarly synthesized SB16, featuring an S-shaped para-benzodipyrrole-based skeleton, yields a low PCE of 0.15% due to the strong side-chain aggregation of SB16. The C-shaped A-DNBND-A skeleton in CB16 and the Y6-series NFAs constitutes the essential structural foundation for achieving exceptional device performance. The central Tz moiety or other A' units can be employed to finely adjust intermolecular interactions. The single-crystal X-ray structure reveals that ortho-benzodipyrrole-embedded A-DNBND-A plays an important role in the formation of a 3D elliptical network packing for efficient charge transport. Solution structures of the PM6:NFAs detected by small- and wide-angle X-ray scattering (SWAXS) indicate that removing the Tz unit in the C-shaped skeleton could reduce the self-packing of CB16, thereby enhancing the complexing and networking with PM6 in the spin-coating solution and the subsequent device film. Elucidating the structure-property-performance relationships of A-DA'D-A-type NFAs in this work paves the way for the future development of structurally simplified A-D-A-type NFAs.

Hot-Casting Strategy Empowers High-Boiling Solvent-Processed Organic Solar Cells with Over 18.5% Efficiency

Most top-rank organic solar cells (OSCs) are manufactured by the halogenated solvent chloroform, which possesses a narrow processing window due to its low-boiling point. Herein, based on two high-boiling solvents, halogenated solvent chlorobenzene (CB) and non-halogenated green solvent ortho-xylene (OX), preparing active layers with the hot solution is put forward to enhance the performance of the OSCs. In situ test and morphological characterization clarify that the hot-casting strategy assists in the fast and synchronous molecular assembly of both donor and acceptor in the active layer, contributing to preferable donor/acceptor ratio, vertical phase separation, and molecular stacking, which is beneficial to charge generation and extraction. Based on the PM6:BO-4Cl, the hot-casting OSCs with a wide processing window achieve efficiencies of 18.03% in CB and 18.12% in OX, which are much higher than the devices processed with room temperature solution. Moreover, the hot-casting devices with PM6:BTP-eC9 deliver a remarkable fill factor of 80.31% and efficiency of 18.52% in OX, representing the record value among binary devices with green solvent. This work demonstrates a facile strategy to manipulate the molecular distribution and arrangement for boosting the efficiency of OSCs with high-boiling solvents.

Stereoisomeric Non-Fullerene Acceptors-Based Organic Solar Cells

Chiral alkyl chains are ubiquitously observed in organic semiconductor materials and can regulate solution processability and active layer morphology, but the effect of stereoisomers on photovoltaic performance has rarely been investigated. For the racemic Y-type acceptors widely used in organic solar cells, it remains unknown if the individual chiral molecules separate into the conglomerate phase or if racemic phase prevails. Here, the photovoltaic performance of enantiomerically pure Y6 derivatives, (S,S)/(R,R)-BTP-4F, and their chiral mixtures are compared. It is found that (S,S) and (R,R)-BTP-4F molecule in the racemic mixtures tends to interact with its enantiomer. The racemic mixtures enable efficient light harvesting, fast hole transfer, and long polaron lifetime, which is conducive to charge generation and suppresses the recombination losses. Moreover, abundant charge diffusion pathways provided by the racemate contribute to efficient charge transport. As a result, the racemate system maximizes the power output and minimizes losses, leading to a higher efficiency of 18.16% and a reduced energy loss of 0.549 eV, as compared to the enantiomerically pure molecules. This study demonstrates that the chirality of non-fullerene acceptors should receive more attention and be designed rationally to enhance the efficiency of organic solar cells.

Halogenated Nonfused Ring Electron Acceptor for Organic Solar Cells with a Record Efficiency of over 17

Three nonfused ring electron acceptors (NFREAs), namely, 3TT-C2-F, 3TT-C2-Cl, and 3TT-C2, are purposefully designed and synthesized with the concept of halogenation. The incorporation of F or/and Cl atoms into the molecular structure (3TT-C2-F and 3TT-C2-Cl) enhances the π-π stacking, improves electron mobility, and regulates the nanofiber morphology of blend films, thus facilitating the exciton dissociation and charge transport. In particular, blend films based on D18:3TT-C2-F demonstrate a high charge mobility, an extended exciton diffusion distance, and a well-formed nanofiber network. These factors contribute to devices with a remarkable power conversion efficiency of 17.19%, surpassing that of 3TT-C2-Cl (16.17%) and 3TT-C2 (15.42%). To the best of knowledge, this represents the highest efficiency achieved in NFREA-based devices up to now. These results highlight the potential of halogenation in NFREAs as a promising approach to enhance the performance of organic solar cells.

Highly Efficient and Stable ITO-Free Organic Solar Cells Based on Squaraine N-Doped Quaternary Bulk Heterojunction

Simultaneously achieving high efficiency and robust device stability remains a significant challenge for organic solar cells (OSCs). Solving this challenge is highly dependent on the film morphology of the bulk heterojunction (BHJ) photoactive blends; however, there is a lack of rational control strategy. Herein, it is shown that the molecular crystallinity and nanomorphology of nonfullerene-based BHJ can be effectively controlled by a squaraine-based doping strategy, leading to an increase in device efficiency from 17.26% to 18.5% when doping 2 wt% squaraine into the PBDB-TF:BTP-eC9:PC71 BM ternary BHJ. The efficiency is further improved to 19.11% (certified 19.06%) using an indium-tin-oxide-free column-patterned microcavity (CPM) architecture. Combined with interfacial modification, CPM quaternary OSC excitingly shows an extrapolated lifetime of ≈23 years based on accelerated aging test, with the mechanism behind enhanced stability well studied. Furthermore, a flexible OSC module with a high and stable efficiency of 15.2% and an overall area of 5 cm2 is successfully fabricated, exhibiting a high average output power for wearable electronics. This work demonstrates that OSCs with new design of BHJ and device architecture are highly promising to be practical relevance with excellent performance and stability.

A-D-A Type Nonfullerene Acceptors Synthesized by Core Segmentation and Isomerization for Realizing Organic Solar Cells with Low Nonradiative Energy Loss

Reducing non-radiative recombination energy loss (ΔEnonrad ) in organic solar cells (OSCs) has been considered an effective method to improve device efficiency. In this study, the backbone of PTBTT-4F/4Cl is divided into D1-D2-D3 segments and reconstructed. The isomerized TPBTT-4F/4Cl obtains stronger intramolecular charge transfer (ICT), thus leading to elevated highest occupied molecular orbital (HOMO) energy level and reduced bandgap (Eg ). According to ELoss  = Eg- qVOC , the reduced Eg and enhanced open circuit voltage (VOC ) result in lower ELoss , indicating that ELoss has been effectively suppressed in the TPBTT-4F/4Cl based devices. Furthermore, compared to PTBTT derivatives, the isomeric TPBTT derivatives exhibit more planar molecular structure and closer intermolecular stacking, thus affording higher crystallinity of the neat films. Therefore, the reduced energy disorder and corresponding lower Urbach energy (Eu ) of the TPBTT-4F/4Cl blend films lead to low ELoss and high charge-carrier mobility of the devices. As a result, benefitting from synergetic control of molecular stacking and energetic offsets, a maximum power conversion efficiency (PCE) of 15.72% is realized from TPBTT-4F based devices, along with a reduced ΔEnonrad of 0.276 eV. This work demonstrates a rational method of suppressing VOC loss and improving the device performance through molecular design engineering by core segmentation and isomerization.

Coplanar Conformational Structure of π-Conjugated Polymers for Optoelectronic Applications

Hierarchical structure of conjugated polymers is critical to dominating their optoelectronic properties and applications. Compared to nonplanar conformational segments, coplanar conformational segments of conjugated polymers (CPs) demonstrate favorable properties for applications as a semiconductor. Herein, recent developments in the coplanar conformational structure of CPs for optoelectronic devices are summarized. First, this review comprehensively summarizes the unique properties of planar conformational structures. Second, the characteristics of the coplanar conformation in terms of optoelectrical properties and other polymer physics characteristics are emphasized. Five primary characterization methods for investigating the complanate backbone structures are illustrated, providing a systematical toolbox for studying this specific conformation. Third, internal and external conditions for inducing the coplanar conformational structure are presented, offering guidelines for designing this conformation. Fourth, the optoelectronic applications of this segment, such as light-emitting diodes, solar cells, and field-effect transistors, are briefly summarized. Finally, a conclusion and outlook for the coplanar conformational segment regarding molecular design and applications are provided.

Impact of the unrelaxed vibrational modes on hot-electron transfer

The ultrafast photoinduced electron or exciton transfer was investigated theoretically. The charge separation on the ultrafast time scale results in the unrelaxed vibrational modes that appear in the initial terms of the generalized master equations. Here, the impact of these initial terms on the electron transfer directionality in the open system was evaluated. Moreover, the role of unrelaxed vibrational modes in electron-hole separation was also examined. It was shown that the unrelaxed vibrational modes significantly increase the efficiency of electron-hole separation. This could play a crucial role in the remarkable efficiency of charge separation in biological systems.

Macrocyclic Encapsulation in a Non-fused Tetrathiophene Acceptor for Efficient Organic Solar Cells with High Short-Circuit Current Density

Non-fullerene acceptors have shown great promise for organic solar cells (OSCs). However, challenges in achieving high efficiency molecular system with conformational unicity and effective molecular stacking remain. In this study, we present a new design of non-fused tetrathiophene acceptor R4T-1 via employing the encapsulation of tetrathiophene with macrocyclic ring. The single crystal structure analysis reveals that cyclic alkyl side chains can perfectly encapsulate the central part of molecule and generate a conformational stable and planar molecular backbone. Whereas, the control 4T-5 without the encapsulation restriction displays cis- and twisted conformation. As a result, R4T-1 based OSCs achieved an outstanding power conversion efficiency (PCE) exceeding 15.10 % with a high short-circuit current density (Jsc ) of 25.48 mA/cm2 , which is significantly improved by ≈30 % in relative to that of the control. Our findings demonstrate that the macrocyclic encapsulation strategy could assist fully non-fused electron acceptors (FNEAs) to achieve a high photovoltaic performance and pave a new way for FNEAs design.

Phenoxy Group-Containing Asymmetric Non-Fullerene Acceptors Achieved Higher VOC over 1.0 V through Alkoxy Side-Chain Engineering for Organic Solar Cells

Alkoxy side chain engineering on the β-position of the thienothiophene units of Y6 derivatives plays a vital role in improving photovoltaic performances with simultaneously increasing open-circuit voltage (Voc) and fill factor (FF). In this work, we prepared a series of asymmetric non-fullerene acceptors (NFAs) by introducing alkoxy side chains and phenoxy groups on the state-of-the-art Y6-derivative BTP-BO-4F. For the comparison, 2O-BO-4F with a symmetric alkoxy side chain on the outer thiophene units and BTP-PBO-4F with an asymmetric N-attached phenoxy alkyl chain on the pyrrole ring are synthesized from BTP-BO-4F. Thereafter, we construct four asymmetric NFAs by introducing different lengths of linear/branched alkoxy chains on the β-position of the thienothiophene units of BTP-PBO-4F. The resulting NFAs, named L10-PBO, L12-PBO, B12-PBO, and B16-PBO (L = linear and B = branched alkoxy side chains), are collectively called OR-PBO-series. Unexpectedly, all OR-PBO NFAs exhibit strong edge-on molecular packing and weaker π-π interactions in the film state, which diminish the charge transfer in organic solar cell (OSC) devices. As a consequence, the optimal devices of OR-PBO-based binary blends show poor photovoltaic performances [power conversion efficiency (PCE) = 6.52-9.62%] in comparison with 2O-BO-4F (PCE = 12.42%) and BTP-PBO-4F (PCE = 15.30%) reference blends. Nevertheless, the OR-PBO-based binary devices show a higher Voc and smaller Vloss. Especially, B12-PBO- and B16-PBO-based devices achieve Voc over 1.00 V, which is the highest value of Y-series OSC devices to the best of our knowledge. Therefore, by utilizing higher Voc of OR-PBO binary blends, B12-PBO and B16-PBO are incorporated into the PM6:BTP-PBO-4F-based binary blend and fabricated ternary devices. As a result, the PM6:BTP-PBO-4F:B12-PBO ternary device delivers the best PCE of 15.60% with an increasing Voc and FF concurrently.

An efficient end-capped engineering of pyrrole-based acceptor molecules for high-performance organic solar cells

CONTEXT

Various innovative molecules have been designed and explored for use in organic photovoltaics. In this study, we devised novel molecules (KZ1-KZ7) specifically for organic solar cells (OSCs). The newly formulated acceptor compounds possess a lower bandgap (Eg = 1.85-2.02), along with bathochromic shift (λmax = 713-788 nm) compared to the reference (Eg = 2.04 eV and λmax = 774 nm). Moreover, the FMO results identified the distinct charge transfer from HOMO to LUMO, which was strongly corroborated by the TDM maps. Similarly, the new designed molecules show less excitation energy (Ex = 1.31-1.54(gas)) than reference (Ex = 1.72). Likewise, all designed molecules (KZ1-KZ7) have demonstrated an analogous open circuit voltage (Voc) with the donor polymer PTB7-Th. All seven designed molecules (KZ1-KZ7) exhibited more fill factor ranging from 97.08 to 97.29 than reference 95.25 and PCE of between 8 and 20% at short circuit current densities of 9, 12, and 15 mA cm-2. Overall, the findings support that designed molecules can be potential molecules for future practical applications.

METHODS

Geometric calculations were conducted with Gaussian 09W software, and the findings were visualized using Gauss View software. DFT and TD-DFT were employed to evaluate various parameters for R and designed molecules (KZ1-KZ7). Firstly, four functionals including B3LYP, CAM-B3LYP, MPW1PW91, and ωB97XD with 6-31G(d,p) DFT level were applied to R to decide the best level for results. After appropriate analysis, the MPW1PW91/6-31G(d,p) was selected for further examination by comparing the experimental and DFT-based absorption graphs of R. External and internal reorganization energy are the two main factors contributing to reorganization energy. External energy refers to changes in external environment, while internal energy deals with information related to internal geometrical symmetry or the internal environment. The effect of outside factors or external reorganizational energy is omitted because it creates too little change.

19.32% Efficiency Polymer Solar Cells Enabled by Fine-Tuning Stacking Modes of Y-Type Molecule Acceptors: Synergistic Bromine and Fluorine Substitution of the End Groups

The success of Y6-type nonfullerene small molecule acceptors (NF-SMAs) in polymer solar cells (PSCs) can be attributed to their unique honeycomb stacking style, which leads to favorable thin-film morphologies. The intermolecular interactions related to the crystallization tendency of these NF-SMAs is closely governed by their electron accepting end groups. For example, the high performance Y6 derivative L8-BO (BTP-4F) presents three types of stacking modes in contrast to two stacking modes of Y6. Hence, it is ultimately interesting to obtain more insight on the packing properties and the preferences influenced by chemical modifications such as end group engineering. This work designs and synthesizes asymmetric and symmetric L8-BO derivatives with brominated end groups and explores the stacking preferences in various modes. The asymmetric BTP-3FBr displays an optimized crystallization tendency and thin film morphology, leading to a decent power conversion efficiency (PCE) of 18.34% in binary devices and a top PCE of 19.32% in ternary devices containing 15 wt% IDIC as the second acceptor.

Low-Cost Fully Non-fused Ring Acceptor Enables Efficient Organic Photovoltaic Modules for Multi-Scene Applications

Organic photovoltaic (OPV) cells, with highly tunable light-response ranges, offer significant potential for use in driving low-power consumption off-grid electronics in multi-scenarios. However, development of photoactive layer materials that can meet simultaneously the requirements of diverse irradiation conditions is a still challenging task. Herein, a low-cost fully non-fused acceptor (denoted as GS60) featuring well-matched absorption spectra with solar, scattered light and artificial light radiation was designed and synthesized. Systematic characterizations revealed that GS60 possessed outstanding photoelectron properties and ideal morphology, which resulted in reduced voltage loss and suppressed charge recombination. By blending with a non-fused ring polymer PTVT-T, the as-obtained GS60 based OPV cells achieved a good power conversion efficiency (PCE) of 14.1 %, a high value for the cells based on non-fused ring bulk heterojunction. Besides, manufactured large-area OPV modules based on PTVT-T:GS60 yielded PCEs of 11.2 %, 11.8 %, 12.1 %, 23.1 %, and 20.3 % under irradiation of AM 1.5G, natural light of cloudy weather, natural light in shadow, laser and indoor, respectively. The PTVT-T:GS60 devices exhibited considerable potential in terms of improving photostability and reducing material cost. Overall, this work provides novel insight into the molecular design of low-cost non-fused ring acceptors, and extended potential of medium band gap acceptors based OPV cells used in various application scenarios.

High-Pressure Fabrication of Binary Organic Solar Cells with High Molecular Weight D18 Yields Record 19.65 % Efficiency

In this work, inspired by the principles of a pressure cooker, we utilized a high-pressure method to address the processing challenges associated with high molecular weight polymers. Through this approach, we successfully dissolved high molecular weight D18 in chloroform at 100 °C within a pressure-tight vial. The increased steam pressure raised the boiling point and dissolving capacity of chloroform, enabling the creation of a hybrid film with superior properties, including more ordered molecular arrangement, increased crystallinity, extended exciton diffusion length, and improved phase morphology. Organic solar cells (OSCs) based on D18 : L8-BO prepared using this high-pressure method achieved an outstanding power conversion efficiency of 19.65 %, setting a new record for binary devices to date. Furthermore, this high-pressure method was successfully applied to fabricate OSCs based on other common systems, leading to significant enhancements in device performance. In summary, this research introduces a universal method for processing high molecular weight D18 materials, ultimately resulting in the highest performance reported for binary organic solar cells.

Constructing High-Performance Ternary Device Using Analogous Polymer Donors

Both ternary copolymerization and ternary blending are effective methods to fine-tune polymer structure and manipulate thin-film morphology to improve device performance. In this work, three D-A-A-A (D: donor, A: acceptor) terpolymer donors (FY1, FY2, and FY3) are synthesized by introducing BDD (1,3-bis(2-ethylhexyl)-5,7-di(thiophen-2-yl)benzo[1,2-c:4,5-c']dithiophene-4,8-dione) units into the D-A alternating copolymer PM6 backbone. Owing to the promoted conjugated planarity and excellent absorption of BDD, the obtained terpolymers display an extended absorption range and enhanced π-π stacking orientation, which is a promising third component in ternary device. As a result, the optimal FY1:PM6:BTP-eC9-based ternary device afforded an impressive power conversion efficiency (PCE) as high as 18.52%, owing to the efficient charge transport, negligible energy loss, and suitable domain size. The result provides an efficient method to obtain high-performance polymer solar cells by using analogous polymer donors in ternary device.

Solution-Processed Semiconductor Materials as Cathode Interlayers for Organic Solar Cells

Cathode interlayers (CILs) play a crucial role in improving the photovoltaic efficiency and stability of OSCs. CILs generally consists of two kinds of materials, interfacial dipole-based CILs and SPS-based CILs. With good charge transporting ability, excellent compatibility with large-area processing methods, and highly tunable optoelectronic properties, the SPS-based CILs exhibit remarkable superiorities to their interfacial dipole-based counterparts in practical use, making them promising candidate in developing efficient CILs for OSCs. This mini-review highlights the great potential of SPS-based CILs in OSC applications and elucidates the working mechanism and material design strategy of SPS materials. Afterward, the SPS-based CIL materials are summarized and discussed in four sections, including organic small molecules, conjugated polymers, nonconjugated polymers, and TMOs. The structure-property-performance relationship of SPS-based CIL materials is revealed, which may provide readers new insight into the molecular design of SPS-based CILs. The mechanisms to endow SPS-based CILs with thickness insensitivity, resistance to environmental erosion, and photo-electric conversion ability are also elucidated. Finally, after a brief summary, the remaining issues and the prospects of SPS-based CILs are suggested.

The central core size effect in quinoxaline-based non-fullerene acceptors for high VOC organic solar cells

For organic solar cells (OSCs), obtaining a high open circuit voltage (VOC) is often accompanied by the sacrifice of the circuit current density (JSC) and filling factor (FF), and it is difficult to strike a balance between VOC and JSC × FF. The trade-off of these parameters is often the critical factor limiting the improvement of the power conversion efficiency (PCE). Extended backbone conjugation and side chain engineering of non-fullerene acceptors (NFAs) are effective strategies to optimize the performance of OSCs. Herein, based on the quinoxaline central core and branched alkyl chains at the β position of the thiophene unit, we designed and synthesized three NFAs with different sized cores. Interestingly, Qx-BO-3 with a smaller central core showed better planarity and more appropriate crystallinity. As a result, PM6:Qx-BO-3-based devices obtained more suitable phase separation, more efficient exciton dissociation, and charge transport properties. Therefore, the OSCs based on PM6:Qx-BO-3 yielded an outstanding PCE of 17.03%, significantly higher than the devices based on PM6:Qx-BO-1 (10.57%) and PM6:Qx-BO-2 (11.34%) although the latter two devices have lower VOC losses. These results indicated that fine-tuning the central core size can effectively optimize the molecular geometry of NFAs and the film morphology of OSCs. This work provides an effective method for designing high-performance NFA-OSCs with high VOCs.

Reducing Depletion Region Width at Electrode Interface via a Hole-transport Layer for Over 18% Efficiency in Organic Solar Cells

The large depletion region width at the electrode interface may cause serious energy loss in charge collection of organic solar cells (OSCs), depressing the open-circuit voltage and power conversion efficiency (PCE). Herein, a pH neutral solution-processed conjugated polyelectrolyte PIDT-F:IMC as hole transport layer (HTL) to reduce the depletion region width in efficient OSCs is developed. By utilizing "mutual doping" strategy, the doping density of PIDT-F:IMC is increased by more than two orders of magnitude, which significantly reduces the depletion region width at the anode interface from 55 to 7.4 nm, playing an effective role in decreasing the energy loss in hole collection. It is also revealed that the optimal thickness of HTL should be consistent with the depletion region width for achieving the minimum energy loss. The OSC modified by PIDT-F:IMC shows a high PCE of 18.2%, along with an amazing fill factor of 0.79. Moreover, a PCE of 16.5% is achieved in the 1 cm2 OSC by using a blade-coated PIDT-F:IMC HTL, indicating the good compatibility of PIDT-F:IMC with large-area processing technology. The PIDT-F:IMC-modified OCS exhibits a lifetime of 400 h under operational conditions, which is ten times longer than that of the PEDOT:PSS device.

Simulation Design of Novel Non-Fluorine Polymers as Electron Transport Layer for Lead-Free Perovskite Solar Cells

Significant progress has been made in the advancement of perovskite solar cells, but their commercialization remains hindered by their lead-based toxicity. Many non-toxic perovskite-based solar cells have demonstrated potential, such as Cs2AgBi0.75Sb0.25Br6, but their power conversion efficiency is inadequate. To address this issue, some researchers are focusing on emerging acceptor-donor-acceptor'-donor-acceptor (A-DA'D-A)-type non-fullerene acceptors (NFAs) for Cs2AgBi0.75Sb0.25Br6 to find effective electron transport layers for high-performance photovoltaic responses with low voltage drops. In this comparative study, four novel A-DA'D-A-type NFAs, BT-LIC, BT-BIC, BT-L4F, and BT-BO-L4F, were used as electron transport layers (ETLs) for the proposed devices, FTO/PEDOT:PSS/Cs2AgBi0.75Sb0.25Br6/ETL/Au. Comprehensive simulations were conducted to optimize the devices. The simulations showed that all optimized devices exhibit photovoltaic responses, with the BT-BIC device having the highest power conversion efficiency (13.2%) and the BT-LIC device having the lowest (6.8%). The BT-BIC as an ETL provides fewer interfacial traps and better band alignment, enabling greater open-circuit voltage for efficient photovoltaic responses.

A pyridine-capped quaterthiophene as an alternative to PEDOT:PSS, processable from organic solvents and without acidity, for more stable electronic devices

Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is a material that has become ubiquitous in the field of organic electronics. It is most commonly used as a hole transport layer (HTL) in optoelectronic devices and can be purchased commercially in various formulations with different properties. Whilst it is a most convenient material to work with, there are stability issues associated with PEDOT:PSS that are detrimental to device stability and these are due to the acidic nature of the PSS component. In this paper, we present a molecular, non-acidic alternative to PEDOT:PSS. The parent structure is composed of a quater(3,4-ethylenedioxythiophene) unit capped either side of the short chain with two pyridine units. This compound, termed (BEDOTPy)2, can be prepared chemically and electrochemically to give doped materials with a choice of counteranions. Further functionalisation via quaternisation at the nitrogen atoms allows for modification of solubility and film-forming properties. The conductivity of the doped samples can reach up to 3.75 S cm-1. The materials are non-acidic and are therefore attractive alternatives to PEDOT:PSS for device applications. We demonstrate an OLED device using the compound (BEDOTPy-EtOH-I)2PF6 as an HTL, and compare the device performance to one made with PEDOT:PSS. Due to the non-acidic nature of the molecular material, the corresponding OLED device does not show a drop in luminance over time, whereas a loss of performance is observed for the device containing PEDOT:PSS over a short period. These results are presented to introduce the parent compound (BEDOTPy)2 as an attractive alternative to PEDOT:PSS, which can be easily modified chemically to provide a plethora of potential compounds with tunable properties.

Improving the Performance of Layer-by-Layer Organic Solar Cells by n-Doping of the Acceptor Layer

Molecular dopants can effectively improve the performance of organic solar cells (OSCs). Here, PM6/BTP-eC9-4Cl-based OSCs are fabricated by a layer-by-layer (LbL) deposition method, and the electron acceptor BTP-eC9-4Cl layer is properly doped by n-type dopant benzyl viologen (BV) or [4-(1,3-dimethyl-2,3-dihydro-1H-benzoimidazol-2-yl)phenyl]dimethyl-amine (N-DMBI-H). The power conversion efficiency (PCE) of OSCs increases from 16.80 to 17.61 or 17.84% when the acceptor layer is doped by BV (0.01 wt %) or N-DMBI-H (0.01 wt %), respectively. At the optimal doping concentration, the device exhibits more balanced charge transport, fewer bimolecular recombinations, faster charge separation and transfer, and better stability. This doping strategy has good universality; when the acceptor layer L8-BO of LbL OSCs is doped by 0.01 wt % BV or 0.01 wt % N-DMBI-H, the PCE increases from 17.49 to 18.35 or 18.25%, respectively. All in all, our studies have demonstrated that the doping strategy is effective in enhancing the performance of OSCs.

A polymer library enables the rapid identification of a highly scalable and efficient donor material for organic solar cells

The dramatic improvement of the PCE (power conversion efficiency) of organic photovoltaic devices in the past few years has been driven by the development of new polymer donor materials and non-fullerene acceptors (NFAs). In the design of such materials synthetic scalability is often not considered, and hence complicated synthetic protocols are typical for high-performing materials. Here we report an approach to readily introduce a variety of solubilizing groups into a benzo[c][1,2,5]thiadiazole acceptor comonomer. This allowed for the ready preparation of a library of eleven donor polymers of varying side chains and comonomers, which facilitated a rapid screening of properties and photovoltaic device performance. Donor FO6-T emerged as the optimal material, exhibiting good solubility in chlorinated and non-chlorinated solvents and achieving 15.4% PCE with L8BO as the acceptor (15.2% with Y6) and good device stability. FO6-T was readily prepared on the gram scale, and synthetic complexity (SC) analysis highlighted FO6-T as an attractive donor polymer for potential large scale applications.

Eliminating the Imbalanced Mobility Bottlenecks via Reshaping Internal Potential Distribution in Organic Photovoltaics

The imbalanced carrier mobility remains a bottleneck for performance breakthrough in even those organic solar cells (OSCs) with recorded power conversion efficiencies (PCEs). Herein, a counter electrode doping strategy is proposed to reshape the internal potential distribution, which targets to extract the low mobility carriers at far end. Device simulations reveal that the key of this strategy is to partially dope the active layer with a certain depth, therefore it strengthens the electric field for low mobility carriers near counter electrode region while avoids zeroing the electric field near collection electrode region. Taking advantage of these, PCE enhancements are obtained from 15.4% to 16.2% and from 16.9% to 18.0%, respectively, via cathode p-doping and anode n-doping. Extending its application from opaque to semitransparent devices, the PCE of dilute cell rises from 10.5% to 12.1%, with a high light utilization efficiency (LUE) of 3.5%. The findings provide practical solutions to the core device physical problem in OSCs.

Ternary Organic Solar Cells with Power Conversion Efficiency Approaching 15% by Fine-Selecting the Third Component

Nonfullerene acceptors with mediate bandgap play a crucial role in ternary devices as the third component, further boosting the performance of organic solar cells (OSCs). Herein, three F-series acceptors (F-H, F-Cl, and F-2Cl) with mediate bandgap are selected and introduced into the PM6:BDT-Br binary system as third component to find the detailed influence of end groups with chlorine (Cl) atom substitution on the performance of ternary organic solar cells. Due to the increased substitution of Cl atoms on the end groups, F-Cl and F-2Cl as guest acceptors reveal a superior ability to regulate the morphology of blend films, contributing to the ordered packing properties and high crystallinity. As a result, F-Cl and F-2Cl based ternary OSCs achieve significantly improved PCEs of 13.89% and 14.67%, respectively, compared with the binary devices (12.70%). On the contrary, F-H without Cl atom displays a poor compatibility with the host system, resulting in an inferior ternary device with a low PCE of 10.79%. This work indicates that F-series acceptors with mediate bandgap are a promising class of third component for high-performance ternary OSCs. And introducing more Cl atoms substitution on the end groups, especially F-2Cl, will own a broad applicability for other binary devices.

Benzotriazole-Based 3D Four-Arm Small Molecules Enable 19.1 % Efficiency for PM6 : Y6-Based Ternary Organic Solar Cells

A third component featuring a planar backbone structure similar to the binary host molecule has been the preferred ingredient for improving the photovoltaic performance of ternary organic solar cells (OSCs). In this work, we explored a new avenue that introduces 3D-structured molecules as guest acceptors. Spirobifluorene (SF) is chosen as the core to combine with three different terminal-modified (rhodanine, thiazolidinedione, and dicyano-substituted rhodanine) benzotriazole (BTA) units, affording three four-arm molecules, SF-BTA1, SF-BTA2, and SF-BTA3, respectively. After adding these three materials to the classical system PM6 : Y6, the resulting ternary devices obtained ultra-high power-conversion efficiencies (PCEs) of 19.1 %, 18.7 %, and 18.8 %, respectively, compared with the binary OSCs (PCE=17.4 %). SF-BTA1-3 can work as energy donors to increase charge generation via energy transfer. In addition, the charge transfer between PM6 and SF-BTA1-3 also acts to enhance charge generation. Introducing SF-BTA1-3 could form acceptor alloys to modify the molecular energy level and inhibit the self-aggregation of Y6, thereby reducing energy loss and balancing charge transport. Our success in 3D multi-arm materials as the third component shows good universality and brings a new perspective. The further functional development of multi-arm materials could make OSCs more stable and efficient.

Terminally Chlorinated and Thiophene-linked Acceptor-Donor-Acceptor Structured 3D Acceptors with Versatile Processability for High-efficiency Organic Solar Cells

To exploit the potential of our newly developed three-dimensional (3D) dimerized acceptors, a series of chlorinated 3D acceptors (namely CH8-3/4/5) were reported by precisely tuning the position of chlorine (Cl) atom. The introduction of Cl atom in central unit affects the molecular conformation. Whereas, by replacing fluorinated terminal groups (CH8-3) with chlorinated terminal groups (CH8-4 and CH8-5), the red-shift absorption and enhanced crystallization are achieved. Benefiting from these, all devices received promising power conversion efficiencies (PCEs) over 16 % as well as decent thermal/photo-stabilities. Among them, PM6:CH8-4 based device yielded a best PCE of 17.58 %. Besides, the 3D merits with multi alkyl chains enable their versatile processability during the device preparation. Impressive PCEs of 17.27 % and 16.23 % could be achieved for non-halogen solvent processable devices prepared in glovebox and ambient, respectively. 2.88 cm2 modules also obtained PCEs over 13 % via spin-coating and blade-coating methods, respectively. These results are among the best performance of dimerized acceptors. The decent performance of CH8-4 on small-area devices, modules and non-halogen solvent-processed devices highlights the versatile processing capability of our 3D acceptors, as well as their potential applications in the future.

Unidirectional Sidechain Engineering to Construct Dual-Asymmetric Acceptors for 19.23 % Efficiency Organic Solar Cells with Low Energy Loss and Efficient Charge Transfer

Achieving both high open-circuit voltage (Voc ) and short-circuit current density (Jsc ) to boost power-conversion efficiency (PCE) is a major challenge for organic solar cells (OSCs), wherein high energy loss (Eloss ) and inefficient charge transfer usually take place. Here, three new Y-series acceptors of mono-asymmetric asy-YC11 and dual-asymmetric bi-asy-YC9 and bi-asy-YC12 are developed. They share the same asymmetric D1 AD2 (D1 =thieno[3,2-b]thiophene and D2 =selenopheno[3,2-b]thiophene) fused-core but have different unidirectional sidechain on D1 side, allowing fine-tuned molecular properties, such as intermolecular interaction, packing pattern, and crystallinity. Among the binary blends, the PM6 : bi-asy-YC12 one has better morphology with appropriate phase separation and higher order packing than the PM6 : asy-YC9 and PM6 : bi-asy-YC11 ones. Therefore, the PM6 : bi-asy-YC12-based OSCs offer a higher PCE of 17.16 % with both high Voc and Jsc , due to the reduced Eloss and efficient charge transfer properties. Inspired by the high Voc and strong NIR-absorption, bi-asy-YC12 is introduced into efficient binary PM6 : L8-BO to construct ternary OSCs. Thanks to the broadened absorption, optimized morphology, and furtherly minimized Eloss , the PM6 : L8-BO : bi-asy-YC12-based OSCs achieve a champion PCE of 19.23 %, which is one of the highest efficiencies among these annealing-free devices. Our developed unidirectional sidechain engineering for constructing bi-asymmetric Y-series acceptors provides an approach to boost PCE of OSCs.

Robust and Sustainable Indium Anode Leading to Efficient and Stable Organic Solar Cells

The fast degradation of the charge-extraction interface at indium tin oxide (ITO) poses a significant obstacle to achieving long-term stability for organic solar cells (OSCs). Herein, a sustainable approach for recycling non-sustainable indium to construct efficient and stable OSCs and scale-up modules is developed. It is revealed that the recovered indium chloride (InCl3 ) from indium oxide waste can be applied as an effective hole-selective interfacial layer for the ITO electrode (noted as InCl3 -ITO anode) through simple aqueous fabrication, facilitating not only energy level alignment to photoactive blends but also mitigating parasitic absorption and charge recombination losses of the corresponding OSCs. As a result, OSCs and modules consisting of InCl3 -ITO anodes achieve remarkable power conversion efficiencies (PCEs) of 18.92% and 15.20% (active area of 18.73 cm2 ), respectively. More importantly, the InCl3 -ITO anode can significantly extend the thermal stability of derived OSCs, with an extrapolated T80 lifetime of ≈10 000 h.

Impact of Electrostatic Interaction on Non-radiative Recombination Energy Losses in Organic Solar Cells Based on Asymmetric Acceptors

Reducing non-radiative recombination energy loss (ΔE3 ) is one key to boosting the efficiency of organic solar cells. Although the recent studies have indicated that the Y-series asymmetric acceptors-based devices featured relatively low ΔE3 , the understanding of the energy loss mechanism derived from molecular structure change is still lagging behind. Herein, two asymmetric acceptors named BTP-Cl and BTP-2Cl with different terminals were synthesized to make a clear comparative study with the symmetric acceptor BTP-0Cl. Our results suggest that asymmetric acceptors exhibit a larger difference of electrostatic potential (ESP) in terminals and semi-molecular dipole moment, which contributes to form a stronger π-π interaction. Besides, the experimental and theoretical studies reveal that a lower ESP-induced intermolecular interaction can reduce the distribution of PM6 near the interface to enhance the built-in potential and decrease the charge transfer state ratio for asymmetric acceptors. Therefore, the devices achieve a higher exciton dissociation efficiency and lower ΔE3 . This work establishes a structure-performance relationship and provides a new perspective to understand the state-of-the-art asymmetric acceptors.

Non-orthogonal Configuration Interaction Study on the Effect of Thermal Distortions on the Singlet Fission Process in Photoexcited Pure and B,N-Doped Pentacene Crystals

The present computational work analyzes singlet fission (SF) as a pathway for multiplication of photogenerated excitons in crystalline polyacenes. Our study explores the well-known crystalline pentacene (C22H14) and the prospective and potentially interesting doped B,N-pentacene (BC20NH14). At the molecular level, the singlet fission process involves a pair of neighboring molecules and is based on the coupling between an excited singlet state (S1S0) and two singlet-coupled triplets (1T1T1), which, typically, is influenced by an intermolecular charge transfer state. Taking data from periodic density functional theory and ab initio wave function calculations, we applied the non-orthogonal configuration interaction method to determine electronic coupling parameters. The comparison of the results for both equilibrium structures reveal smaller SF coupling for pentacene than for B,N-pentacene by a factor of ∼5. Introduction of the dynamic behavior to the crystals (vibrations, thermal motion) provides a more realistic picture of the effect of the disorder at the molecular level on the SF efficiency. The coupling values associated to out-of-equilibrium structures show that most of the S1S0/1T1T1 couplings remain virtually constant or slightly increase for pentacene when molecular disorder is introduced. Homologous calculations on B,N-pentacene show a generalized decrease in the coupling values, notably if large phonon displacements are considered. A few of the structures analyzed feature much larger SF coupling if some distortion results in (nearly) degenerate charge transfer and excited singlet and triplet states. For these particular situations, an acceleration of the SF process could occur although in competition with electron-hole separation as an alternative pathway.

Asymmetric Non-Fullerene Acceptor Derivatives Incorporated Ternary Organic Solar Cells

Incorporating ITIC derivatives as guest acceptors into binary host systems is an effective strategy for constructing high-performance ternary organic solar cells (TOSCs). In this work, we introduced A-D-A type ITIC derivatives PTBTT-4F (asymmetric) and PTBTP-4F (symmetric) into the PM6:BTP-BO-4F (Y6-BO) binary blend and investigated the impacts of two guest acceptors on the performance of TOSCs. Differentiated device performance was observed, although PTBTT-4F and PTBTP-4F presented similar chemical structures and comparable absorptions. The PTBTT-4F ternary devices exhibited an improved power conversion efficiency (PCE) of 17.67% with increased open circuit (VOC) and current density (JSC), whereas the PTBTP-4F-based ternary devices yielded a relatively lower PCE of 16.34%. PTBTT-4F showed much better compatibility with the host acceptor BTP-BO-4F, so that they formed a well-mixed alloy phase state; more precise phase separation and increased crystallinity were thus induced in the ternary blends, leading to reduced molecular recombination and improved charge mobilities, which contributed to improved fill factors of the ternary devices. In addition, the optimized PTBTT-4F devices exhibited good performance tolerance of the photoactive layer thickness, as they even delivered a PCE of 15.25% when the active layer was as thick as up to ∼300 nm.

Conformational Locking Control of 2D Outer Side Chains via Fluorine Atom Positioning for Improving the Thermal Stability of Organic Solar Cells

Alongside high power conversion efficiencies (PCEs), device stability, especially thermal issues, is another key factor for the successful commercialization of nonfullerene acceptor (NFA)-based organic solar cells (OSCs). Considering the significant effects of the side-chain engineering of NFAs on molecular packing and/or locking strongly associated with the thermal stability of OSCs, herein, we present two new isomeric NFAs with 4-fluoro- and 2-fluoro-substituted hexylphenyl two-dimensional (2D) outer side chains (4FY and 2FY, respectively). In contrast with the 2FY having a horizontal stretching conformation, 4FY exhibits a diagonal stretching conformation of the 2D outer side chains and a higher dipole moment, resulting in a huge difference in their crystalline/aggregation characteristics, i.e., 4FY possesses a higher crystallinity with a denser molecular packing than the 2FY neat film, as evidenced by thermal and morphological characterizations. Encouragingly, relative to the one based on 2FY, the OSC based on 4FY delivers a PCE as high as 16.4%, together with excellent thermal stability (88.4% PCE retention under 85 °C for 360 h), which is attributed to a more optimal and robust blend morphology induced by its better compatibility into the used donor component and stronger crystallinity. This work demonstrates that in addition to the improved photovoltaic property, the appropriate F-positioning on the 2D outer side chains can play a key role in controlling their conformations, which can promote the increase of the thermal stability of OSCs.

Extending Se substitution to the limit: from 5S to 5Se in high-efficiency non-fullerene acceptors

Based on the newly synthesized seleno[3,2-b]selenophene unit, two near-infrared non-fullerene acceptors (NFAs) of 4Se and 5Se are constructed by replacing four or all sulfurs with selenium in high-efficiency Y-series NFAs. Consequently, binary devices based on 4Se and 5Se afford PCEs of 15.17% and 15.23%, respectively, with a photoelectric response approaching 1000 nm. More excitingly, the energy loss of the 5Se-based device was as low as 0.477 eV along with almost the smallest non-radiative loss of ∼0.15 eV thus far.

Suppressing electron-phonon coupling in organic photovoltaics for high-efficiency power conversion

The nonradiative energy loss (∆Enr) is a critical factor to limit the efficiency of organic solar cells. Generally, strong electron-phonon coupling induced by molecular motion generates fast nonradiative decay and causes high ∆Enr. How to restrict molecular motion and achieve a low ∆Enr is a sticking point. Herein, the free volume ratio (FVR) is proposed as an indicator to evaluate molecular motion, providing new molecular design rationale to suppress nonradiative decay. Theoretical and experimental results indicate proper proliferation of alkyl side-chain can decrease FVR and restrict molecular motion, leading to reduced electron-phonon coupling while maintaining ideal nanomorphology. The reduced FVR and favorable morphology are simultaneously obtained in AQx-6 with pinpoint alkyl chain proliferation, achieving a high PCE of 18.6% with optimized VOC, JSC and FF. Our study discovered aggregation-state regulation is of great importance to the reduction of electron-phonon coupling, which paves the way to high-efficiency OSCs.

Manipulating the Alkyl Chains of Naphthodithiophene Imide-Based Polymers to Concurrently Boost the Efficiency and Stability of Organic Solar Cells

Morphology instability holds the major responsibility for efficiency degradation of organic solar cells (OSCs). However, how to develop polymer donors simultaneously with high efficiency and excellent morphology stability remains challenging. Herein, we reported naphtho[2,1-b:3,4-b']dithiophene-5,6-imide (NDTI)-based new polymers PNDT1 and PNDT2. The alkyl chain engineering leads to high crystallinity, high hole mobility (>10-3 cm2 V-1 S-1), and nanofibrous film morphology, which enable PNDT2 to exhibit an efficiency of 18.13% and a remarkable FF value of 0.80. Moreover, the NDTIs have short π-π stacking and abundant short interactions, and their polymers exhibit superior morphological stability. Therefore, the PNDT2-based OSCs exhibit much better device stability than that of PNDT1, PAB-α, and benchmark polymers PM6 and D18. This work suggests the great importance of the large conjugated backbone of the monomer and alkyl chain engineering to develop high-performance and morphology-stable polymers for OSCs.

p-Type Conjugated Polymers Containing Electron-Deficient Pentacyclic Azepinedione

Bisthienoazepinedione (BTA) has been reported for constructing high-performing p-type conjugated polymers in organic electronics, but the ring extended version of BTA is not well explored. In this work, we report a new synthesis of a key building block to the ring expanded electron-deficient pentacyclic azepinedione (BTTA). Three copolymers of BTAA with benzodithiophene substituted by different side chains are prepared. These polymers exhibit similar energy levels and optical absorption in solution and solid state, while significant differences are revealed in their film morphologies and behavior in transistor and photovoltaic devices. The best-performing polymers in transistor devices contained alkylthienyl side chains on the BDT unit (pBDT-BTTA-2 and pBDT-BTTA-3) and demonstrated maximum saturation hole mobilities of 0.027 and 0.017 cm2 V-1 s-1. Blends of these polymers with PC71BM exhibited a best photovoltaic efficiency of 6.78% for pBDT-BTTA-3-based devices. Changing to a low band gap non-fullerene acceptor (BTP-eC9) resulted in improved efficiency of up to 13.5%. Our results are among the best device performances for BTA and BTTA-based p-type polymers and highlight the versatile applications of this electron-deficient BTTA unit.

A rare case of brominated small molecule acceptors for high-efficiency organic solar cells

Given that bromine possesses similar properties but extra merits of easily synthesizing and polarizing comparing to homomorphic fluorine and chlorine, it is quite surprising very rare high-performance brominated small molecule acceptors have been reported. This may be caused by undesirable film morphologies stemming from relatively larger steric hindrance and excessive crystallinity of bromides. To maximize the advantages of bromides while circumventing weaknesses, three acceptors (CH20, CH21 and CH22) are constructed with stepwise brominating on central units rather than conventional end groups, thus enhancing intermolecular packing, crystallinity and dielectric constant of them without damaging the favorable intermolecular packing through end groups. Consequently, PM6:CH22-based binary organic solar cells render the highest efficiency of 19.06% for brominated acceptors, more excitingly, a record-breaking efficiency of 15.70% when further thickening active layers to ~500 nm. By exhibiting such a rare high-performance brominated acceptor, our work highlights the great potential for achieving record-breaking organic solar cells through delicately brominating.

Alkyl side chain engineering enables high performance as-cast organic solar cells of over 17% efficiency

Achieving high-performance as-cast OSCs is crucial for industrialization in the future, owing to the advantages of better stability, environmental-friendly, and decreasing production cost. In this regard, we synthesized an A-DA'D-A type acceptor, Y6-eC6-BO, by shortening the straight alkyl side-chains on the thiophene position from C11 to C6 as well as lengthening the branched alkyl side-chains on the pyrrole position of Y6 to achieve a stronger crystallization and better miscibility than Y6. As a result, the corresponding chloroform-processed as-cast PM6: Y6-eC6-BO OSC showed a high PCE of 17.33%, which was one of the highest efficiencies of as-cast OSCs. And the as-cast PM6:Y6-eC6-BO OSCs processed from o-xylene displayed a PCE of 16.38%, as far as we know, this is among the highest efficiencies of non-halogenated-solvent processed as-cast OSCs. These results demonstrated tailoring the alkyl side-chain of NFAs is a feasible and simple approach to achieve high performance as-cast OSCs and provides guideline in molecular design in the future.

Dimerized Small-Molecular Acceptor Enables the Organic Bulk-Heterojunction Layer with High Thermal Stability

Incorporation of a non-fullerene acceptor (NFA) into an organic bulk-heterojunction currently has realized the extendable spectral response and high photocurrent generation in organic photodiodes. However, to allow these organic materials to be industrially commercialized, the thermal stability which enables the materials to survive under the process integration and operation needs to be considered. Generally, NFA small molecules showed high crystallinity, which aggregated through heating and led to the poor thermal stability. To tackle the thermal stability issue of highly efficient NFAs, two IDIC-based NFA dimers─IDIC-T Dimer and IDIC-TT Dimer─were designed, synthesized, and characterized; the thermal stability of the BHJ layer incorporating these dimer molecules was evaluated and compared with that of the BHJ layer using the monomer, IDIC-4Cl, as acceptors. Eventually, a power conversion efficiency of 9.44% was achieved for organic photovoltaic devices based on the NFA dimer. The dimers also showed remarkable thermal stability than the IDIC-4Cl monomer, which provided a promising direction for the polymer/small-molecule system in organic photodiodes for industrial practicability.