Overview of capillary electrophoresis and capillary electrochromatography

Aptamer-based enantioselective competitive binding assay for the trace enantiomer detection

The development of highly enantioselective assays and sensors has received much attention for the determination of enantiomeric impurities at a low level. For chiral compounds, the efficient monitoring of the in selection procedure has allowed the isolation of nucleic acid aptamers which are able to strongly discriminate the target enantiomers. In this paper, we demonstrated for the first time that an aptamer can be successfully used to design a highly enantioselective tool for the trace enantiomer detection. The aptamer-based stereoselective assay was developed using an affinity capillary electrophoresis-based competitive, homogeneous format and an on-capillary mixing approach. Detection of as low as 0.01% of the minor enantiomer in a nonracemic mixture can be achieved, in a short analysis time (<5 min).

Analysis of nitrosamines by capillary electrospray-high-field asymmetric waveform ion mobility spectrometry-MS with programmed compensation voltage

Emerging disinfection by-products (DBPs) in drinking water are an important public health concern. Certain DBPs, such as nitrosamines, are probable carcinogens, and exposure to halogenated DBPs may lead to birth defects. It is difficult to obtain complete separation of nitrosamines by chromatographic techniques. Thus we explored high-field asymmetric waveform ion mobility spectrometry (FAIMS) as an alternative separation technique for the characterization of individual DBPs in a complex matrix. We first used ESI-FAIMS-MS to separate four nitrosamines: N-nitrosodi-n-butylamine (NDBA), N-nitrosodi-n-propylamine (NDPA), N-nitrosopiperidine (NPip), and N-nitrosodiethylamine (NDEA) in the compensation voltage (CV) spectra. The optimal CVs with a fixed dispersion voltage of -4000 V were found to be -1.2 V (NDBA), 2.7 V (NDPA), 7.5 V (NPip) and 10.1 V (NDEA). In addition, FAIMS-MS effectively reduced the chemical noise and dramatically improved the LODs by as much as tenfold compared to the conventional ESI-MS technique. To further improve sensitivity, an on-line CE system was used in combination with FAIMS-MS to take advantage of the higher ionization efficiency. The calibration curves for the four nitrosamines were linear over a range of 5 ng/mL to 1000 ng/mL with an r(2 )value of 0.9929 to 0.9992. To increase sample throughput, a multiple-injection strategy was developed, in which the CV values were preprogrammed so that the FAIMS device allowed different nitrosamines to pass through at selected time windows. The potential application of the proposed method was demonstrated for the analysis of drinking water samples spiked with nitrosamines.

Method of determination of nitrosamines in sausages by CO2 supercritical fluid extraction (SFE) and micellar electrokinetic chromatography (MEKC)

In this paper, the use of supercritical fluid extraction (SFE) and micellar electrokinetic capillary chromatography (MEKC) is proposed for the complete analysis of volatile nitrosamines in sausages. The extraction fluid used was CO2 and variables such as density, temperature of thimbles, extraction time, modifier, fluid flow, and kind of traps were investigated. Several experiments were carried out to obtain the most favorable conditions for analysis of volatile nitrosamines in sausages. The recoveries ranged from 21 to 82% for the five nitrosamines studied. The optimal condition of extraction was 0.2 g of sample fortified with 10 mg/kg, using dynamic extraction during 20 min and with adsorbent Florisil in the trap. The solvent selected for the elution of the analytes was methanol.

Preparation of fritless capillary using avidin immobilized magnetic particles for electrochromatographic chiral separation

In capillary electrochromatography (CEC), magnetic particles (MPs) were packed in a fused silica capillary by using the magnetic field to be retained without frits. For a chiral CEC separation, avidin was immobilized onto the surface of the MPs (AVI-MPs) as a stationary phase by using the physical adsorption technique. The injected AVI-MPs into the capillary were stably captured with the magnet (surface magnetic flux density, 250 mT) under the separation voltage of 10 kV (190 V/cm). By employing the fritless AVI-MPs packed capillary, the chiral separation of ketoprofen was successfully attained with the packing length of only 5 cm. Effects of the modification condition of avidin, pH of background solution, and the packing length on the enantioseparation were also investigated. Under the optimal condition, furthermore, the repeatability for the retention time of ketoprofen was better than 1.5% in the relative standard deviation and the capillary-to-capillary reproducibility was also acceptable in the prepared fritless capillaries.

Enhanced separation of purine and pyrimidine bases using carboxylic multiwalled carbon nanotubes as additive in capillary zone electrophoresis

This paper describes the enhanced separation of adenine (A), hypoxanthine (HX), 8-azaadenine (8-AA), thymine (T), cytosine (C), uracil (U) and guanine (G) by CZE dispersing carboxylic multiwalled carbon nanotubes (c-MWNTs) into the running buffer. The effect of important factors such as c-MWNT nanoparticle concentration, the acidity and concentration of running buffer, and separation voltage were investigated to acquire the optimum conditions. The seven purine and pyrimidine bases could be well separated within 16 min in a 35 cm effective length fused-silica capillary at a separation voltage of +8.0 kV in a 23 mM tetraborate buffer (pH 9.2) containing 8.0 x 10(-5) g/mL c-MWNTs. Under the optimal conditions, the linear ranges were of 2-250 microg/mL for A (R2 = 0.995), 3-200 microg/mL for U (R2 = 0.990) and G (R2 = 0.992), 3-250 microg/mL for T (R2 = 0.998), 2-200 microg/mL for C (R2 = 0.985) and 4-200 microg/mL for HX (R2 = 0.988) and 8-AA (R2 = 0.990). The detection limits were 0.9 microg/mL for A (S/N = 3), 2.4 microg/mL for U, 2.0 microg/mL for T, 1.5 microg/mL for C, 2.5 microg/mL for G and 3.0 microg/mL for HX and 8-AA. The proposed method was successfully applied for determining five purine and pyrimidine bases in yeast RNA.

Comparison of a non-aqueous capillary electrophoresis method with high performance liquid chromatography for the determination of herbicides and metabolites in water samples

A method of capillary electrophoresis (CE) for the determination of triazine herbicides and some of their main metabolites in water samples has been developed. The proposed CE method includes an off-line solid-phase extraction (SPE) procedure with LiChrolut EN sorbent coupled to a non-aqueous capillary electrophoresis (NACE) separation with UV detection. The target compounds were the chloro-s-triazines simazine, atrazine, propazine; the methyltio-s-triazines ametryn and prometryn and three main derivatives from the atrazine degradation products; namely, deethylatrazine, deethylhydroxyatrazine and deisopropylhydroxyatrazine. The analytical characteristics of the CE method are reported. The repeatability of the method was studied considering the different steps of the method separately in order to determine the contributions of each step to the total variability of the method. The NACE-UV results are compared with those obtained with a high performance liquid chromatography with UV detection (HPLC-UV) method. The same off-line SPE procedure was applied to both techniques. The results obtained show that both methods afford the same results in the analysis of surface and drinking water samples, with a level of significance regarding the F- and t-tests greater than 0.05 in all the cases. The detection limits in surface water samples were in the 0.04-0.32 microg l(-1) and 0.11-1.2 microg l(-1) ranges for the NACE-UV and HPLC-UV methods, respectively. The recoveries (spiked/found) were significantly 100% in all cases.

Enhancement of electroosmotic flow using zwitterionic additives

Zwitterionic additives provide a means of altering the EOF without increasing conductivity. The magnitude of the EOF in a bare silica capillary increased by as much as 69% upon addition of 500 mM of zwitterion to the running buffer. The EOF enhancement increases linearly with the zwitterion concentration. With zwitterionic additives of the form +NH3-(CH2)n-COO-, the magnitude of the EOF increase is directly related to the number of methylene groups, (n), which ranges from n = 1 to 7. The endgroups on the zwitterions also affect the EOF enhancement. The effect of Z1-methyl (+N(CH3)3CH2CH2CH2SO3-) on EOF was not a function of either the buffer cation or pH. The EOF enhancement is a function of the dielectric increment of the additive and the nature of the amine functionality.

Determination of paeonol and paeoniflorin in Chinese medicine Cortex Moutan and 'Shuangdan' granule by micellar electrokinetic capillary chromatography

An easy, simple and rapid micellar electrokinetic capillary chromatography (MEKC) method was developed for the separation of two active components paeonol (PN) and paeoniflorin (PF) within 7 min. Capillary electrophoresis (CE) was performed using a 50.0 cm (42.0 cm to the detector window) x 75 microm i.d. fused-silica capillary. The optimal running buffer containing 10mM borate and 25 mM SDS at pH 9.54 was employed. The applied voltage 15 kV and the temperature 25 degrees C was used in CE separation. The linearities between peak areas and the concentrations of the analytes were investigated, and they exhibited excellent linear behavior over the investigated concentration ranges (R(2): 0.9945 for PN and 0.9992 for PF). The method was successfully applied to the determination of these two components contained in Cortex Moutan and 'Shuangdan' granule. The average recoveries ranged between 97.6 and 105.3% for PN and 95.3 and 106.1% for PF, respectively.

Analysis of nucleic acid constituents by on-line capillary electrophoresis-mass spectrometry

This review is focused on the capillary electrophoresis-mass spectrometric (CE-MS) analysis of nucleic acid constituents in the broadest sense, going from nucleotides and adducted nucleotides over nucleoside analogues to oligonucleotides. These nucleic acid constituents play an important role in a variety of biochemical processes. Hence, their isolation, identification, and quantification will undoubtedly help reveal the process of life and disease mechanisms, such as carcinogenesis, and can also be useful for antitumor and antiviral drug research to provide valuable information about mechanism of action, pharmacokinetics, pharmacodynamics, toxicity, therapeutic drug level monitoring, and quality control related to this substance class. Fundamental investigations into their structure, the search for modifications, the occurrence and biochemical impact of structural variation amongst others, are therefore of great value. In view of the related bioanalytical procedures, the coupling of CE to MS has emerged as a powerful tool for the analysis of the complex mixtures of nucleic acid constituents: CE confers rapid analysis and efficient resolution, while MS provides high selectivity and sensitivity with structural characterization of minute amounts of compound. After an introduction about the biochemical and analytical perspectives on the nucleic acid constituents, the different modes of CE used in this field of research as well as the relevant CE-MS interfaces and the difficulties associated with quantitative CE-MS are briefly discussed. A large section is finally devoted to field-oriented applications.

Fast analysis of pravastatin in production media

High throughput methods (high performance liquid chromatography and capillary electrophoresis) were developed to determine pravastatin in production media. The analyses were performed on particle column, monolithic column and silica capillary filled with borate buffer pH 9.3 containing 20 mM SDS. All three methods successfully separate pravastatin from interfering compounds (matrix, mevastatin and 6-epi pravastatin) and runtimes are shorter than 1 min. Solvent consumptions for methods using small particle column, monolith column and MECK were 132, 510 and 1.5 mL h(-1). The most sensitive was the method using particle column (LOD was about 10(-5) mg mL(-1)), followed by the system using monolith column (LOD was 2 x 10(-4) mg mL(-1)) and the MECK method (LOD was about 0.02 mg mL(-1)).

Determination of levoglucosan from smoke samples using microchip capillary electrophoresis with pulsed amperometric detection

Separation and detection of native anhydrous carbohydrates derived from the combustion of biomass using an electrophoretic microchip with pulsed amperometric detection (PAD) is described. Levoglucosan represents the largest single component of the water extractable organics in smoke particles and can be used to trace forest fires or discriminate urban air pollution sources. Detection of levoglucosan and other sugar anhydrides in both source and ambient aerosol samples is typically performed by gas chromatographic (GC) separation with mass spectrometric (MS) detection. This method is cost, time, and labor intensive, typically involving a multistep solvent extraction, chemical derivatization, and finally analysis by GC/MS. However, it provides a rich wealth of chemical information as the result of the combination of a separation method and MS and exhibits good sensitivity. In contrast, microchip capillary electrophoresis offers the possibility of performing simpler, less expensive, and faster analysis. In addition, integrated devices can be fabricated and incorporated with an aerosol collection system to perform semicontinuous, onsite analysis. In the present report, the effect of the separation potential, buffer pH and composition, injection time, and pulsed amperometric detection parameters were studied in an effort to optimize both the separation and detection of anhydrous sugars. Using the optimized conditions, the analysis can be performed in less than a minute, with detection limits ranging from 22 fmol (16.7 microM) for levoglucosan to 336 fmol (258.7 microM) for galactosan. To demonstrate the capabilities of the device, a comparison was made between GC/MS and microchip electrophoresis using an aerosol source sample generated in a wood-burning chamber. A second example utilizing an ambient aerosol sample illustrates a matrix interference necessitating additional method development for application to samples not dominated by wood smoke.

Allelopathic potential and systematic evaluation of organic extracts from Canavalia ensiformis leaves (Jack beans)

This article describes the assessment of possible allelopathic potential of organic extracts obtained from leaves of Canavalia ensiformis under laboratory conditions. Furthermore, a systematic evaluation of these extracts was carried out using specific protocols developed in capillary electrophoresis (CE) to determine some groups of secondary metabolites. After the identification and quantification of compounds, the effects of compounds on germination of some common weeds was investigated, which are becoming a real problem in pastures in the state of Pará, Brazil.

Mass spectrometric methods for the determination of flavonoids in biological samples

There is an ever-increasing interest in the biological effects of the bioflavonoids, members of the large group of plant polyphenols. Because of the aromatic character of these compounds, they have been analyzed by several chromatographic methods. In the case of high-performance liquid chromatography, they are readily detected by their ultraviolet absorbance or electrochemical properties. More evidence that the bioflavonoids undergo extensive metabolism during uptake from the gut and distribution around the body and in specific tissues is accumulating. In addition, free radical products at sites of inflammatory processes react with bioflavonoids and their metabolites, generating important new compounds of as yet unknown properties. For these reasons, careful examination of the chemical nature of bioflavonoids and their products in biological systems is absolutely required. Combination of mass spectrometry with the various chromatographic methods has proved to be highly successful in this regard. This review of the literature on the bioflavonoids is focused on the methods that are currently available for their qualitative and quantitative analysis by mass spectrometry and covers the period 2001-2003. Emphasis is placed on the description and value of existing methods, followed by an examination of emerging technologies.

Polymerised bicontinuous microemulsions as stationary phases for capillary electrochromatography

Monolithic columns for capillary electrochromatography (CEC) were prepared by in situ polymerisation of bicontinuous microemulsions containing butyl methacrylate. The resulting monoliths were found to be permeable to mobile phase flow and their behaviour as CEC stationary phases was investigated. It was found that the monoliths were able to separate a simple test mixture of phthalates, but that efficiencies were low. However, several advantages of the monoliths compared to conventional ODS packed columns were found: preparation time is short, many columns can be prepared from the same batch of microemulsion and column conditioning is much faster. The columns show promise as stationary phases for CEC, but more development is required to improve efficiencies.

A prototype microfluidic platform for miniaturization and automation of serial dilution and dose-response assays

A novel microfluidic device was designed and developed to miniaturize, multiplex, and automate serial dilution and three-reagent dose-response assays using submicroliter quantities of reagents. This prototype microfluidic device can be used to measure enzyme kinetics and to test a chemical lead's response to a target by fluorescent readout using common plate readers and detection systems. The prototype microfluidic system yielded serial dilution and dose-response assay data comparable to results obtained from manual titrations and reagent additions performed using a microwell plate. Enzyme kinetics were highly reproducible using these devices, although Michaelis-Menten kinetics results differed from those obtained in the microwell plate. In all cases reported here, assays performed on the microfluidic format required lower volumes of reagents compared with the microwell plate. In addition to savings in reagent consumption, the microfluidic devices and bench-top instruments offer additional advantages over conventional solutions, including a small footprint and compatibility with commercially available fluorescence detectors. Future directions for the prototype technology are discussed.

Effects of peak anomalies with the hydrophilic or hydrophobic properties of reservoirs during serial injection on a capillary electrophoresis microchip

Several anomalies, e.g., in peak shape, migration time, and baseline drift, all due to pressure-driven backflow, were previously reported to occur during serial injection on capillary electrophoresis (CE) chips. Since these anomalies were worse for polydimethylsiloxane (PDMS) microchips than for glass microchips, reproducible data on PDMS microchips were difficult to obtain. In this paper, we found that these problems were affected by the hydrophilic or hydrophobic properties of the reservoirs on the microchip and demonstrated that these anomalies were reduced by converting the hydrophobic properties of the reservoirs on the PDMS microchip into hydrophilic ones. Thus, compared with hydrophobic reservoirs, hydrophilic reservoirs were suitable for the formation of a stable plug. Several chip designs were suggested to reduce these pressure-driven backflows.

Separation of purine and pyrimidine bases by capillary electrophoresis using β-cyclodextrin as an additive

Capillary electrophoresis was applied to separate purine and pyrimidine bases in the basis of their partial ionization in the alkaline buffer. The effects of buffer pH, buffer and beta-cylclodextrin concentration were systematically investigated using a commercial capillary electrophoresis instrument with UV detector at 254nm. We found that the resolutions of bases (especially for adenine and thymine) were significantly improved in the presence of beta-cylclodextrin. The satisfactory separation of five bases such as cytosine, thymine, adenine, guanine and uracil were achieved by capillary electrophoresis using beta-cylclodextrin as an additive. Under the optimal conditions, the linear range was from 2 to 200microg/ml for bases (R= 0,991-0,9977 ) and the detection limits were from 0.8 to 1.8microg/ml (S/N = 2). The detection limit of 0.05microg/ml ( S/N=2 ) for uracil was obtained by stacking injection mode. The assay was used to determine the deamination of cytosine to uracil by heating in the presence of sodium hydroxide. Our primarily results show that capillary electrophoresis is a very useful tool for determination of purine and pyrimidine bases and study on nucleic acids.

Development and validation of a high-resolution capillary electrophoresis method for multi-analysis of ragaglitazar and arginine in Active Pharmaceutical Ingredients and low-dose tablets

A selective, sensitive and robust capillary electrophoresis (CE) method has been developed and validated for multi analysis of ragaglitazar (also known as NNC 61-0029 or DRF 2725) and its counter ion arginine in Active Pharmaceutical Ingredients (API) and low-dose tablets (0.5, 1.0 and 2.0 mg). The method covers a total number of 12 analyses for the API and tablets: assay and identification of ragaglitazar and arginine, chiral purity of ragaglitazar and purity of ragaglitazar. After a simple extraction of samples with acetonitrile and 0.01 M sodium hydroxide (10:90), separation was performed using a combination of two cyclodextrins; sulfobutylether-beta-cyclodextrin (SB-beta-CD) and dimethyl-beta-cyclodextrin (DM-beta-CD) in the electrolyte. The method showed good specificity and could separate and detect ragaglitazar, the distomer (the (+)-enantiomer) and arginine. The LOQ was found to be 0.10%, corresponding to 0.2 ng (0.5 microg/ml) for ragaglitazar and the distomer. Linearity was observed to be from 0.5 to 15 microg/ml (range 0.2-60 ng) and 400-600 microg/ml (range 1603-2404 ng) for ragaglitazar and 166-250 microg/ml (range 668-1000 ng) for arginine. The accuracy (as percent recovery) for ragaglitazar was found to be 101-106% (at 400-600 microg/ml), 101-125% (at 0.5-15 microg/ml) and for arginine 97-101% (at 166-250 microg/ml). The repeatability for the detection of peaks as R.S.D. was found to be as follows, ragaglitazar: 0.05%, distomer: 1.01%, largest single impurity: 5.84%, total impurities: 0.90% and arginine: 2.00%. The intermediate precision for the detection of peaks as R.S.D. was found to be as follows, ragaglitazar: 0.63%, distomer: 1.98%, largest single impurity: 5.22%, total impurities: 13.17% and arginine: 3.50.

Comparative study for separation of aquatic humic substances by capillary zone electrophoresis using uncoated, polymer coated and gel-filled capillaries

Several comparative capillary zone electrophoresis (CZE) experiments were carried out by means of uncoated, polyvinyl alcohol (PVA) and polyacrylamide (PAA) coated silica open tubular capillaries and gel-filled capillaries (linear non-cross-linked polyacrylamide, PAGE, by a pre-coated PAA capillary) using different kinds of background electrolytes (BGEs) and organic modifiers for characterization of aquatic dissolved humic matter (DHM). Organic compounds, such as acetic acid, acetate buffer, methanol, ethylene glycol, acetonitrile, dimethylsulphoxide, 5 M urea and sodium dodecyl sulphate (SDS) were tested as sample modifiers to improve the separative power. The fractionation mode by a PVA coated open tubular capillary using 40 mM phosphate buffer at pH 6.8 and 5 M urea-water as the sample modifier turned out to be fairly practical as well as its PAA homologue. Linear non-cross-linked PAGE with 10% gel concentration and 5 M urea-water as the sample modifier using 40 mM phosphate buffer at pH 6.8 produced the most reliable results as to the adaptation of physical gels, especially if the interactions of humic solutes with the gel matrix are not critical. The addition of SDS in the linear PAGE gel increased the interaction of humic solutes with the gel matrix but also improved the separative power and strengthened the chaotropic effect of the urea modifier.

Caracterização de ácidos húmicos de diferentes origens por eletroforese capilar de zona

O objetivo deste trabalho foi caracterizar ácidos húmicos (HA) de diferentes origens por eletroforese capilar de zona (CZE) e avaliar a influência da concentração do tampão borato nesta caracterização. Os resultados mostraram que HA de diferentes origens podem ser rapidamente caracterizados por CZE. Por esta técnica, a caracterização de HA é devido a diferenças na razão carga/tamanho e das propriedades dos componentes individuais, conseqüência de suas diferentes origens.

Development of a Sheathless Interface between Reversed-Phase Capillary HPLC and ICPMS via a Microflow Total Consumption Nebulizer for Selenopeptide Mapping

A sheathless interface based on a total consumption micronebulizer operating at flow rates in the range 0.5-7.5 microL min(-1) was developed between capillary HPLC and ICPMS. It allowed the efficient nebulization and transport into the plasma of mobile phases containing up to 100% organic solvent without either cooling the spray chamber or oxygen addition. The coupled system was applied to selenopeptide mapping in a protein fraction isolated from a selenized yeast extract. The detection limits were 150 (80Se) and 200 fg (82Se) for a quadrupole instrument with and without a collision cell, respectively, which is a factor 100-150 less than that reported elsewhere for HPLC-ICPMS. The minimal peak broadening ( approximately 5 s at the half-height) allowed baseline resolution of a mixture containing more than 30 selenopeptides, many of which could not be separated using the conventional HPLC-ICPMS coupling.

Optimization of a capillary electrophoretic method to detect and quantify the Gly-Pro dipeptide in complex matrices from long term cultured prolidase deficiency fibroblasts

A capillary electrophoresis (CE) method has been developed and optimized for the detection of Gly-Pro dipeptide in complex biological samples: medium, cell layer and matrix obtained from long term cultured human fibroblasts of control and prolidase deficiency patients. The influence of different detergents in the sample preparation and electrophoretic conditions were investigated. The method was validated for cellular extracts with respect to limits of detection and quantitation, precision, linearity, accuracy and robustness. The optimized method was applied to real samples and revealed a significant increase of intracellular Gly-Pro dipeptide in prolidase deficiency fibroblasts with respect to the control.

Capillary electrophoresis and its application in the clinical laboratory

Over the past 10 years, capillary electrophoresis (CE) is an analytical tool that has shown great promise in replacing many conventional clinical laboratory methods, especially electrophoresis and high performance liquid chromatography (HPLC). The main attraction of CE was that it was fast, used small amounts of sample and reagents, and was extremely versatile, being able to separate large and small analytes, both neutral and charged. Because of this versatility, numerous methods for clinically relevant analytes have been developed. However, with the exception of the molecular diagnostic and forensic laboratories CE has not had a major impact. A possible reason is that CE is still perceived as requiring above-average technical expertise, precluding its use in a laboratory workforce that is less technically adept. With the introduction of multicapillary instruments that are more automated, less technique-dependent, in addition to the availability of commercial and cost effective test kit methods, CE may yet be accepted as a instrument routinely used in the clinical laboratories. Thus, this review will focus on the areas where CE shows the most potential to have the greatest impact on the clinical laboratory. These include analysis of proteins found in serum, urine, CSF and body fluids, immunosubstraction electrophoresis, hemoglobin variants, lipoproteins, carbohydrate-deficient transferrin (CDT), forensic and therapeutic drug screening, and molecular diagnostics.

Determination of nitrosamines in preserved sausages by solid-phase extraction-micellar electrokinetic chromatography

A new methodology for extraction, pre-concentration and analysis of nitrosamines in meat derived products was developed. The samples (canned sausages) were distilled in vacuum steam and the nitrosamines were pre-concentrated by solid-phase extraction with active carbon. Then, micellar electrokinetic chromatography was used for the separation and determination of the different nitrosamines contained in a real sample and gas chromatography with mass spectrometry detection was used as the confirmation technique. The method allowed the determination of nitrosamine compounds at trace levels with relative standard deviation ranging from 4.0 to 22%.

Recent progress in derivatization methods for LC and CE analysis

The derivatization procedure with a suitable fluorescence or chemiluminescence reagent is performed for the purpose of increasing the detection sensitivity and selectivity, in high-performance liquid chromatography (HPLC) and/or capillary electrophoresis (CE). In this article, recent derivatization methods and their applications to biosamples are described. In HPLC, femto mol order of mass detection limits are obtained by derivatization. Regarding the fluorescence reagents, the use of water-soluble reagents has been effective to avoid an undesired adsorption in the process of determination of peptides. In CE, the advantages of having extremely low mass detection limits (ranging from atto to yocto mol level) and requiring only a very short analysis time (less than a few minutes) are made possible by using laser-induced fluorescence or near infra-red detections.

Peak compression effects in capillary electrochromatography of basic drug substances using a strong cation-exchanger

Peak compression effects in capillary electrochromatography of basic drug substances using a strong cation-exchanger have been studied. Extremely narrow peaks with apparent efficiencies of several million plates per meter could be obtained when the composition of the sample zone differed from that of the mobile phase. The increased efficiencies were predominately observed when the analyte had an elution time similar to that of the electroosmotic flow marker. Peak compression was found to be reproducible and could be obtained for all investigated basic drug substances by altering the composition of the mobile phase in such a way that the analyte co-eluted with the sample zone. An explanation of the observed phenomena is proposed. A sample zone differing in composition from the mobile phase will disturb the equilibrium between the stationary and mobile phase. The elution rate of an analyte will consequently be different when residing inside the sample zone. If the analyte migrates through the sample zone at a higher speed than the rest of the mobile phase and is strongly retained after passing through a boundary in the sample zone, a continuous stacking can be obtained trapping the analyte as a very narrow band.

Review of the methods used in the determination of phytoestrogens

Interest in analytical methods for plant estrogens (phytoestrogens) has risen sharply in the past 10 years. In this review, we examine the existing analytical methods based on separations by gas-liquid chromatography, high-performance liquid chromatography and capillary electrophoresis in addition to methods of detection by ultraviolet absorption, fluorescence, electrochemical oxidation/reduction and mass spectrometry. These methods are compared with other methods of phytoestrogen analysis utilizing immunoassay approaches. The advantages and disadvantages of each of these methods are highlighted and potential areas for further development identified.

Ability of porous graphitic carbon to support electroosmotic flow in capillary electrochromatography

The existence of a cathodic EOF (electroosmotic flow) in the case of a porous graphitic carbon (PGC) partially packed column has been demonstrated. Then, the ability of PGC to afford electroosmosis has been brought to the fore with a fully PGC packed column. Experimental data have shown that PGC particles are negatively charged and their electrophoretic mobility has been evaluated. In order to investigate the conditions of existence of EOF different mobile phases have been tested. An EOF occurs when the conductivity of the PGC packed column is larger than the conductivity of an empty fused-silica capillary operating in the same conditions i.e. when the PGC participates in the electric conduction. Since the local electric fields in the two segments of the column are different, an evaluation of the electroosmotic mobility is not possible and the effect of the operational parameters such as the composition of the mobile phase (acetonitrile ratio and total ionic strength) has been studied in term of electroosmotic velocity V(eo).

Perspectives on analyses of nucleic acid constituents: the basis of genomics

The recent mapping of the human genome was a tremendous achievement made possible to a large degree by the development of analytical methods for sequencing purine and pyrimidine bases in nucleic acids. In the last 3 decades, the number of analyses of nucleic acids and their constituents by HPLC and capillary electrophoresis (CE) has exploded. These techniques have been used not only for genomics, but also for the determination of free nucleotides, nucleosides and their bases in body fluids and tissues. Although a large number of HPLC and CE papers have been published on nucleic acid constituent applications, relatively little has been written on the mechanisms of the separations. However, to optimize analytical conditions knowledgeably and rapidly, it is important to know why and how these separations occur and the factors that affect them. The HPLC methods for the analysis of nucleic acid constituents and the information available on some of the mechanisms of separation of nucleotides, nucleosides and their bases, as well as the analysis of these compounds by CE and the factors that affect these separations are discussed.

Methods for biocatalyst screening

Biocatalysts are now widely accepted as useful alternative tools to classic organic synthetic techniques for the regio- and enantioselective synthesis under mild reaction conditions in many fields of chemistry. The development of techniques for the rational or evolutionary design of novel or modified enzymes has increased the need for fast and reliable methods for the identification of the most powerful catalysts. We present a short overview on screening techniques in this area. Beside classical methods such as spectrophotometry and fluorimetry, a number of new approaches like methods based on the measurement of pH changes or IR-thermography have been recently developed. Additionally the use of electrospray and matrix-assisted laser desorption/ionization mass spectrometry has gained increasing influence in this field of biotechnology.

Immunoaffinity screening with capillary electrochromatography

Highly efficient capillary electrochromatographic separations of cardiac glycosides and other steroids are presented. Employing butyl-derivatized silica particles as stationary phase resulted in a nearly three times faster electroosmotic flow (EOF) compared to capillary electrochromatography (CEC) with octadecyl silica particles. On-column focusing with a preconcentration factor of 180 was performed and separation efficiencies of up to 240,000 plates per meter were obtained. Using label-free standard UV absorbance, detection limits of 10-80 nM were reached for all steroids tested. For screening of cardiac glycosides, e.g., digoxin and digitoxin in mixtures of steroids, CEC was combined with immunoaffinity extraction using immobilized polyclonal anti-digoxigenin antibodies and F(ab) fragments. Simply adding small amounts of antibody carrying particles to the samples and comparing chromatograms before and after antibody addition allowed screening for high affinity antigens in mixtures with moderate numbers of compounds. Under conditions of competing antigens, affinity fingerprints of immobilized anti-digoxigenin and anti-digitoxin antibodies were obtained, reflecting the cross-reactivity of eleven steroids. The method provides high selectivity due to the combination of bioaffinity interaction with highly efficient CEC separation and UV detection at several wavelengths in parallel. This selectivity was exploited for the detection of four cardiac glycosides in submicromolar concentrations in an untreated urine sample.

Novel approach for fritless capillary electrochromatography

At present, the main limitation for the further adoption of capillary electrochromatography (CEC) in the (routine) laboratory is caused by the lack of reproducible and stable columns. The main source of column instability is concentrated in the frits needed to retain the packed bed inside the CEC capillary. The sintering process used to prepare the frits can be rather problematic and irreproducible, particularly for small stationary phase particles and wide column diameters. Since the (surface) composition of the frits is different from the bulk stationary phase packing, different electroosmotic flow (EOF) velocities are generated. This effect is assumed to be primarily responsible for rapid column destruction. In this contribution, a novel approach for the preparation of fritless CEC capillaries is presented and evaluated. Using 5 microm Hypersil ODS particles, separation efficiencies in the range of 130,000-200,000 plates/m were obtained. In a 100 microm inner diameter packed column, electrical currents up to 50 microA could be tolerated without negative effects such as bubble formation. The prepared CEC columns were found to be stable and could easily be operated continuously for several days without column damage. An additional advantage of the proposed tapering approach is that application of pressure on the in- and outlet vial during separation was not required to prevent bubble formation.