Heavy metal pollution in the aquatic environment: efficient and low-cost removal approaches to eliminate their toxicity: a review

Equilibrium, Kinetic, and Diffusion Mechanism of lead(II) and cadmium(II) Adsorption onto Commercial Activated Carbons

The adsorption of Pb(II) and Cd(II) on three commercial microporous activated carbons was analysed. Adsorption kinetics and statistics were investigated, and the results were described with different models. The highest values of the correlation coefficient R2 were obtained for the pseudo-second-order kinetics model for all ions tested and all sorbents used. The adsorption process was found to be determined by both diffusion in the liquid layer and intraparticle diffusion. The adsorption equilibrium is very well described by Langmuir, Temkin, Thoth or Jovanovic isotherm models. Based on the values of n from the Freundlich isotherm and KL from the Langmuir isotherm, the adsorption of cadmium and lead ions was found to be favourable. The highest monolayer capacities were obtained during the adsorption of lead ions (162.19 mg/g) and for cadmium (126.34 mg/g) for activated carbon WG-12. This carbon is characterised by the highest amount of acid functional groups and the largest specific surface area. The adsorption efficiency of the tested ions from natural water is lower than that from a model solution made from deionised water. The lowest efficiencies are obtained when the process occurs from highly mineralised water.

Enhancing copper and lead adsorption in water by in-situ generation of calcium carbonate on alginate/chitosan biocomposite surfaces

Chitosan (CS) and sodium alginate (SA)-based biocomposites (CSA) were prepared with the in-situ generation of Calcium Carbonate (CSAX_Ca) through a simple, straightforward, economical, and eco-friendly procedure. Different drying conditions (X) were tested to achieve suitable structural and surface characteristics to enhance adsorption capacity: freeze-dried (L), vacuum-dried with methanol (M), and freeze-dried + vacuum-dried with methanol (LM). Temperature and adsorbent dosage effects on the adsorption capacity of Cu2+ or Pb2+ were examined. Results showed that the higher-yielding biocomposite (CSALM_Ca) exhibited rapid adsorption and good diffusion properties, achieving removal above 90 % within contaminant initial concentration ranges of 10-100 mg/L. At 35 °C, a pseudo-second-order kinetic and the Langmuir model effectively described kinetics and isotherms, revealing maximum adsorption (qe, max) of 429 mgCu2+/L and 1742 mgPb2+/g. Characterization through FTIR, XRD, and SEM of the as-prepared adsorbents confirmed the presence of CaCO3 in vaterite and calcite forms and the influence of drying conditions on the material morphology. Post-adsorption material characterization, in combination with adsorption findings, revealed chemisorption processes involving Ca2+ ion exchange for Cu2+ or Pb2+, resulting in surface-insoluble compounds. The best-performing material showed that after three reuse cycles, the removal of Cu2+ and Pb2+ decreased to 75 % and 62 %, respectively.

Advancements in application of modified biochar as a green and low-cost adsorbent for wastewater remediation from organic dyes

Synthetic organic dyes, which are resistant to biodegradation, pose a notable health risk, potentially leading to cancer and respiratory infections. Researchers have addressed this concern by exploring physicochemical methods to remove organic dyes from wastewater. A particularly promising solution involves modified biochar adsorbents, which demonstrate high efficiency in organic dye removal. Biochar, a charcoal-like material derived from biomass pyrolysis, offers advantages such as low cost, eco-friendliness, high efficiency and reusability. Beyond its role in sustainable soil remediation, biochar proves effective in removing organic dyes from wastewater after undergoing physical or chemical modification. Acid-base activation or metal-heteroatom impregnation enhances biochar's adsorption capacity. This comprehensive review examines the attributes of biochar, common methods for production and modification, and the impacts of raw materials, pyrolysis temperature, heating rate and residence time. It further elucidates the biochar adsorption mechanism in the removal of organic dyes, assessing factors influencing efficiency, including biochar feedstock, solution pH, adsorption temperature, particle size, initial dye concentration, biochar dosage and reaction time. It explores challenges, opportunities, reusability and regeneration methods of biochar in treating organic dye wastewater. It also discusses recent advances in organic dye removal using adsorption-based biochar. The review ultimately advocates for enhancing biochar's adsorption performance through post-modification.

Carbon Dots Modified Multi Dopants Nitrogen and Boron for an Early Detection of Lead in the Environment

The remarkable optical properties and strong biocompatibility of carbon dots make them highly promising for applications in biochemical sensing and environmental testing. These carbon dots possess a surface that is easily modifiable. In this study, carbon dots have been successfully synthesized and modified by the addition of N and B dopants using the microwave method, along with the functionalization of their surface functional groups with bovine serum albumin (BSA). The maximum fluorescence intensity of N, B-CDs is observed at 462 nm when excited at a wavelength of 352 nm. N, B-CDs have a spherical size with a diameter ranging from 2 to 6 nm, confirmed by UV-Vis absorption spectra and the presence of functional groups in the FT-IR absorption patterns. BSA-functionalized N, B-CDs as the fluorescent probe demonstrate great potential as a sensor for Pb(II) ions in water, with a very low detection limit of 1.05 µg/L. This research could contribute to the development of fluorescence nanosensors.

Assessing the Health Risk and Trophic Transfer of Lead and Cadmium in Dairy Farming Systems in the Mantaro Catchment, Central Andes of Peru

This study investigated lead (Pb) and cadmium (Cd) transfer in three dairy farming areas in the Mantaro river headwaters in the central Peruvian Andes and at varying distances from the mining complex at La Oroya. At each of these sites, the transfer of trace metals from the soil to raw milk was estimated, and a hazard assessment for lead and cadmium was carried out in scenarios of minimum, average, and maximum milk consumption in a Peruvian population aged 2-85. Pb and Cd were quantified by flame atomic absorption spectrometry. Significantly, the concentrations of lead and cadmium were found to exceed the maximum limits recommended by the World Health Organization, with a positive geospatial trend correlated with the distance from mining activity. Both Pb and Cd were found to be transferred through the soil-pasture-milk pathway, with the primary source of Cd being phosphate-based fertilizers used in pasture improvement. Pb was found to be the most significant contributor to the Hazard Index (HI) with those under 19 years of age and over 60 recording an HI of >1, with infants being the most vulnerable group due to their greater milk consumption in relation to their body weight. A marginal increase in contamination was observed in the dry season, indicating the need for studies to be expanded over several annual cycles.

Oxidative stress, inflammation, and steatosis elucidate the complex dynamics of HgCl2 induced liver damage in Channa punctata

Water bodies are highly pollution-prone areas in which mercury (Hg) is considered as a major menace to aquatic organisms. However, the information about the toxicity of mercuric chloride (HgCl2) in a vital organ such as the liver of fish is still inadequate. This study aimed to assess the impact of mercuric chloride (HgCl2) exposure on the liver of Channa punctata fish over 15, 30, and 45 days, at two different concentrations (0.039 mg/L and 0.078 mg/L). Mercury is known to be a significant threat to aquatic life, and yet, information regarding its effects on fish liver remains limited. The results of this study demonstrate that exposure to HgCl2 significantly increases oxidative stress markers, such as lipid peroxidation (LPO) and protein carbonyls (PC), as well as the levels of serum glutamic-oxaloacetic transaminase (SGOT) and serum glutamic pyruvic transaminase (SGPT) in the fish. Additionally, the transcriptional and protein analysis of specific genes and molecules associated with necroptosis and inflammation, such as ABCG2, TNF α, Caspase 3, RIPK 3, IL-1β, Caspase-1, IL-18, and RIPK1, confirm the occurrence of necroptosis and inflammation in the liver. Histopathological and ultrastructural examinations of the liver tissue further reveal a significant presence of liver steatosis. Interestingly, the upregulation of PPARα suggests that the fish's body is actively responding to counteract the effects of liver steatosis. This study provides a comprehensive analysis of oxidative stress, biochemical changes, gene expression, protein profiles, and histological findings in the liver tissue of fish exposed to mercury pollution in freshwater environments.

Electrochemical Detection of Cd2+, Pb2+, Cu2+ and Hg2+ with Sensors Based on Carbonaceous Nanomaterials and Fe3O4 Nanoparticles

Two electrochemical sensors were developed in this study, with their preparations using two nanomaterials with remarkable properties, namely, carbon nanofibers (CNF) modified with Fe3O4 nanoparticles and multilayer carbon nanotubes (MWCNT) modified with Fe3O4 nanoparticles. The modified screen-printed electrodes (SPE) were thus named SPE/Fe3O4-CNF and SPE/Fe3O4-MWCNT and were used for the simultaneous detection of heavy metals (Cd2+, Pb2+, Cu2+ and Hg2+). The sensors have been spectrometrically and electrochemically characterized. The limits of detection of the SPE/Fe3O4-CNF sensor were 0.0615 μM, 0.0154 μM, 0.0320 μM and 0.0148 μM for Cd2+, Pb2+, Cu2+ and Hg2+, respectively, and 0.2719 μM, 0.3187 μM, 1.0436 μM and 0.9076 μM in the case of the SPE/ Fe3O4-MWCNT sensor (following optimization of the working parameters). Due to the modifying material, the results showed superior performance for the SPE/Fe3O4-CNF sensor, with extended linearity ranges and detection limits in the nanomolar range, compared to those of the SPE/Fe3O4-MWCNT sensor. For the quantification of heavy metal ions Cd2+, Pb2+, Cu2+ and Hg2+ with the SPE/Fe3O4-CNF sensor from real samples, the standard addition method was used because the values obtained for the recovery tests were good. The analysis of surface water samples from the Danube River has shown that the obtained values are significantly lower than the maximum limits allowed according to the quality standards specified by the United States Environmental Protection Agency (USEPA) and those of the World Health Organization (WHO). This research provides a complementary method based on electrochemical sensors for in situ monitoring of surface water quality, representing a useful tool in environmental studies.

Exploring the adoption of water quality trading as an alternative stormwater regulatory compliance strategy for land development projects: A case study for Roanoke, Virginia

Urban stormwater runoff is a significant source of nutrient pollution that is very costly to treat. Water quality trading (WQT) is a market-based strategy that can be used to lower the costs associated with meeting stormwater quality regulations. While many WQT programs have experienced low participation, Virginia's program has seen high participation due to the inclusion of land developers and other regulated stormwater dischargers. However, the extent to which WQT is used as a compliance option by regulated stormwater dischargers is not well understood, particularly when compared with the adoption of traditional compliance options. To address this knowledge gap, we collated a novel dataset comprising site characteristics and stormwater compliance methods for all development projects in the City of Roanoke, Virginia from December 2015 to March 2022. We analyzed this dataset to characterize the adoption of nutrient offset credits and other compliance methods being used, including best management practices (BMPs) and improved land covers associated with reduced nutrient export. Results show that credits are the preferred compliance option in Roanoke and were used as the only treatment compliance method for 59% of projects with treatment requirements. Projects using credits corresponded with a lower median disturbed area (1.36 acres) and lower median nutrient load reduction requirement (0.69 pounds of total phosphorus per year) compared with other compliance methods. Furthermore, we found that 58% of the projects that used credits achieved stormwater quantity compliance using methods other than implementing stormwater control devices. By mapping buyers and sellers of credits, we found that all credit sellers are downstream of the development projects. We discuss how this downstream trading could be a cause for concern, as part of a larger discussion of the advantages of tracking stormwater compliance methods, drawing on Roanoke as a case study.

Exploring the fluorescence properties of tellurium-containing molecules and their advanced applications

This review article explores the fascinating realm of fluorescence using organochalcogen molecules, with a particular emphasis on tellurium (Te). The discussion encompasses the underlying mechanisms, structural motifs influencing fluorescence, and the applications of these intriguing phenomena. This review not only elucidates the current state of knowledge but also identifies avenues for future research, thereby serving as a valuable resource for researchers and enthusiasts in the field of fluorescence chemistry with a focus on Te-based molecules. By highlighting challenges and prospects, this review sparks a conversation on the transformative potential of Te-containing compounds across different fields, ranging from environmental solutions to healthcare and materials science applications. This review aims to provide a comprehensive understanding of the distinct fluorescence behaviors exhibited by Te-containing compounds, contributing valuable insights to the evolving landscape of chalcogen-based fluorescence research.

Potential application of 2D nano-layered MXene in analysing and remediating endocrine disruptor compounds and heavy metals in water

With the advancement of technologies and growth of the economy, it is inevitable that more complex processes are deployed, producing more heterogeneous wastewater that comes from biomedical, biochemical and various biotechnological industries. While the conventional way of wastewater treatment could effectively reduce the chemical oxygen demand, pH and turbidity of wastewater, trace pollutants, specifically the endocrine disruptor compounds (EDCs) that exist in µg L-1 or ng L-1 have further hardened the detection and removal of these biochemical pollutants. Even in small amounts, EDC could interfere human's hormone, causing severe implications on human body. Hence, this review elucidates the recent insights regarding the effectiveness of an advanced 2D material based on titanium carbide (Ti3C2Tx), also known as MXene, in detecting and removing EDCs. MXene's highly tunable feature also allows its surface chemistry to be adjusted by adding chemicals with different functional groups to adsorb different kinds of EDCs for biochemical pollution mitigation. At the same time, the incorporation of MXene into sample matrices also further eases the analysis of trace pollutants down to ng L-1 levels, thereby making way for a more cleaner and comprehensive wastewater treatment. In that sense, this review also highlights the progress in synthesizing MXene from the conventional method to the more modern approaches, together with their respective key parameters. To further understand and attest to the efficacy of MXene, the limitations and current gaps of this potential agent are also accentuated, targeting to seek resolutions for a more sustainable application.

An overview of the ameliorative efficacy of Catharanthus roseus extract against Cd2+ toxicity: implications for human health and remediation strategies

Rapid industrialization has led to an increase in cadmium pollution, a dangerously toxic heavy metal. Cadmium (Cd) is released into the environment through industrial processes and can contaminate air, water, and soil. This pollution poses a significant risk to human health and has become a pressing concern in many industrialized areas. Due to its extended half-life, it leads to a range of health problems, including hepato-nephritic toxicity, brain damage, and degenerative bone disorders. Intoxication alters various intracellular parameters, leading to inflammation, tissue injury, and oxidative stress within cells, which disrupts normal cellular functions and can eventually result in cell death. It has also been linked to the development of bone diseases such as osteoporosis. These adverse effects highlight the urgent need to address cadmium pollution and find effective solutions to mitigate its impact on human health. This article highlights the Cd-induced risks and the role of Catharanthus roseus (C. roseus) extract as a source of alternative medicine in alleviating the symptoms. Numerous herbal remedies often contain certain bioactive substances, such as polyphenols and alkaloids, which have the power to mitigate these adverse effects by acting as antioxidants and lowering oxidative cell damage. Research conducted in the field of alternative medicine has revealed its enormous potential to meet demands that may be effectively used in safeguarding humans and their environment. The point of this review is to investigate whether C. roseus extract, known for its bioactive substances, is being investigated for its potential to mitigate the harmful effects of cadmium on health. Further investigation is needed to fully understand its effectiveness. Moreover, it is important to explore the potential environmental benefits of using C. roseus extract to reduce the negative effects of Cd. This review conducted in the field of alternative medicine has revealed its enormous potential to meet demands that could have significant implications for both human health and environmental sustainability.

Synthesis of functionalized mesoporous silica nanoparticles for colorimetric and fluorescence sensing of selective metal (Fe3+) ions in aqueous solution

The fabrication of red fluorescent hybrid mesoporous silica-based nanosensor materials has promised the bioimaging and selective detection of toxic pollutants in aqueous solutions. In this study, we present a hybrid mesoporous silica nanosensor in which the propidium iodide (PI) was used to conveniently integrate into the mesopore walls using bis(trimethoxysilylpropyl silane) precursors. Various characterization techniques including X-ray diffraction (XRD), Fourier-transform infrared (FTIR), N2 adsorption-desorption, zeta potential, particle size analysis, thermogravimetric, and UV-visible analysis were used to analyze the prepared materials. The prepared PI integrated mesoporous silica nanoparticles (PI-MSNs) selective metal ion sensing capabilities were tested with a variety of heavy metal ions (100 mM), including Ni2+, Cd2+, Co2+, Zn2+, Cr3+, Cu2+, Al3+, Mg2+, Hg2+ and Fe3+ ions. Among the investigated metal ions, the prepared PI-MSNs demonstrated selective monitoring of Fe3+ ions with a significant visible colorimetric pink color change into orange and quenching of pink fluorescence in an aqueous suspension. The selective sensing behavior of PI-MSNs might be due to the interaction of Fe3+ ions with the integrated PI functional fluorophore present in the mesopore walls. Therefore, we emphasize that the prepared PI-MSNs could be efficient for selective monitoring of Fe3+ ions in an aqueous solution and in the biological cellular microenvironment.

Optimization of fenugreek seed mucilage extraction for the synthesis of a novel bio-nano composite for efficient removal of cadmium ions from aqueous environments

This research investigates the application of an innovative bio-nanocomposite, Fenugreek seed mucilage/silicon carbide (FSM/SiC), as an exceptionally effective adsorbent for eliminating cadmium ions from aqueous solutions. Optimization of fenugreek mucilage extraction involved ultrasonic methods, establishing ideal conditions with a solid-to-solvent ratio of 1:55, 50 °C temperature, 37 kHz frequency, 100 % power, and 30 min processing time. Comprehensive characterization through FTIR spectroscopy, XRD, imaging, DLS, and SEM confirmed the preservation of crucial adsorption-related characteristics. Enhanced adsorption efficiency was achieved by systematically adjusting pH, temperature, adsorbent concentration, pollutant concentration, and contact time, identifying optimal conditions at pH 6, 0.03 g adsorbent dosage, 35 min contact time, and 30 mg/L initial cadmium concentration at 30 °C. Adsorption kinetics followed a pseudo-second-order model, while the Langmuir isotherm fit suggested monolayered adsorption. Thermodynamic analysis indicated exothermic and spontaneous Cd2+ ion adsorption onto FSM/SiC. Remarkably, FSM/SiC demonstrated exceptional regeneration potential, positioning it as a promising solution for water decontamination and environmental remediation. This research showcases FSM/SiC's potential with a maximum adsorption capacity of 41.6 mg/g for cadmium ions, highlighting its significance in addressing cadmium contamination.

Fine-tuning bromide AIE probes for Hg2+ detection in mitochondria with wash-free staining

Mercury ions (Hg2+) primarily target mitochondria in the cells. Therefore, the development of novel probes that specifically target mitochondria in the presence of Hg2+ is of immense importance. Most previously reported probes that utilize the softness of S, Te, O, and/or N atoms for Hg2+ binding often face problems such as fluorescence quenching and off-target signals. In this study, bromide-hydrocarbon pyridinium salts were designed to target the mitochondria and chelate Hg2+ via Hg-Br coordination bonds. As a prototype, four aggregation-induced emission (AIE) fluorogens, namely TPP-Br, TPP-Cl, R1, and R2, with a similar D-π-A structure but slight differences in their halogen substituents, were designed. Among them, only TPP-Br achieved the highly selective and sensitive detection of Hg2+ by triggering its AIE properties, resulting in remarkable emission enhancement (80-fold), colorimetry, and the Tyndall effect. TPP-Br exhibited high selectivity and sensitivity to Hg2+ with a detection limit of 0.35 μM, rapid response time (<10 s), and large Stokes shift of 185 nm. Their interaction modes were studied using a combination of 1H nuclear magnetic resonance spectroscopy, scanning electron microscopy, fluorescent lifetime decay, and theoretical calculations. TPP-Br exhibited a low emission background in cells, whereas in the presence of Hg2+, mitochondria were lit up with wash-free staining. This study provides a powerful tool for accurately diagnosing mercury poisoning-related diseases in mitochondria.

The competitive and selective adsorption of heavy metals by struvite in the Pb(II)-Cd(II)-Zn(II) composite system and its environmental significance

The prevalence of struvite and other phosphate minerals in eutrophic environments has a significant effect on the transport and transformation of environmental heavy metals, but their competitive immobilization characteristics and mechanisms for heavy metals remain unclear. Three different sources of struvite (BS, CSHS, and CSS) were obtained respectively by biosynthesis and chemical synthesis with or without humic acid to investigate their competitive immobilization characteristics and mechanism of heavy metals in the Pb(II)-Cd(II)-Zn(II) composite system. The results showed that the immobilization of heavy metals by struvite is physico-chemical adsorption and the affinity (in descending order) is Pb(II) >> Cd(II)/Zn(II). Cd(II) promotes the immobilization of Pb(II)/Zn(II) by BS. The order of the selective strength by struvite for Pb(II) is BS >> CSS ≈ CSHS. The study indicates that the difference between struvite holding heavy metal ions is related to the material composition and heavy metal types, and BS shows best selective immobilization for Pb(II) in the Pb(II)-Cd(II)-Zn(II) composite system. This study provides a theoretical basis for understanding the environmental geochemical role and eco-environmental effects of struvite.

Impaired intestinal immunity and microbial diversity in common carp exposed to cadmium

Waterborne cadmium (Cd) accumulates in the fish intestine and causes irreversible toxicity by disrupting intestinal immunity and microbial diversity. To explore the toxicity of environmentally available high Cd concentration on intestinal immunity and microbial diversity of fish, we selected the widely used bioindicator model species, Common carp (Cyprinus carpio). Literature review and Cd pollution data supported sequential doses of 0.2, 0.4, 0.8, 1.6, 3.2, and 6.4 mg/L Cd for 30 days. Based on intestinal tissue Cd accumulation, previous studies, and environmentally available Cd data, 0.4 and 1.6 mg/L Cd were selected for further studies. Intestinal Cd bioaccumulation increased significantly to ~100 times in fish exposed to 1.6 mg/L Cd. We observed villous atrophy, increased goblet cells with mucus production, muscularis erosion, and thickened lamina propria due to intense inflammatory cell infiltration in the intestine at this Cd concentration. Cd-induced immunosuppression occurred with increased lysozyme, alkaline phosphate (AKP), and acid phosphate (ACP). High levels of catalase (CAT), total antioxidant capacity (T-AOC), malondialdehyde (MDA), and hydrogen peroxide (H2O2) suggested induced oxidative stress and poor metabolism by α-amylase and lipase suppression for Cd toxicity. Proteobacteria (41.2 %), Firmicutes (21.8 %), and Bacteroidetes (17.5 %) were the dominant bacterial phyla in the common carp intestine. Additionally, potential pathogenic Cyanobacteria increased in Cd-treated fish. The decrease of beneficiary bacteria like Aeromonas, and Cetobacterium indicated Cd toxicity. Overall, these findings indicate harmful consequences of high Cd concentration in the intestinal homeostasis and health status of fish.

Screening and signifying the uranium remediation level of Alternanthera philoxeroides and Eichhornia crassipes from aquatic medium

Uranium is causing a hazardous impact on the human population throughout the globe. Different methods of remediation have been documented but the approach of phytoremediation has been praised throughout the globe. The bioaccumulation of uranium especially as a hyper-accumulator, has been documented in limited plant species. Therefore the current studies were conducted to elaborate on the overall U accumulation, biochemical and photochemical reactions in Alternanthera philoxeroides and Eichhornia crassipes to different concentrations of Uranium. The results showed that the accumulation of U in A.philoxeroides is higher; followed by E.crassipes; with maximum amounts of roots accumulation. Overall A.philoxeroides and E.crassipes accumulate as much as 948.88 mg/kg and 801.87 mg/kg on a dry weight basis. The biochemical results showed that Superoxide dismutase (SOD) decreased in the leaves and stem of A.philoxeroides; whereas an increase has been seen in E.crassipes in response to all treatments. peroxidase (POD) and Catalase (CAT) showed irregular response to all treatments; where the main increase was observed at T3 (120 μmol/L) and 72 h up to 138 μ/g-FW (POD) and 178 μ/g-FW (CAT) in A.philoxeroides and 1870 μ/g-FW (POD) and 73 μ/g-FW (CAT) in E.crassipes, respectively. The correlation coefficient between the fluorescence ratio Fv/Fm and the concentrations of U-treatment was significantly negative. It is concluded from the results that Uranium halted the biochemical and photochemical reaction but the plants resisted its impact while accumulating a good amount of uranium which is a good prospect for future interventions for the in-situ remediation of uranium-affected sites.

Exploring the potential reuse of phosphogypsum: A waste or a resource?

Phosphogypsum (PG), the main industrial by-product of phosphate fertilizer industry, primarily consists of calcium sulfate dihydrate. However, it contains various impurities with variable quantities depending on the origin of the phosphate rock. These impurities can restrict the reuse of phosphogypsum as a secondary primary resource. Consequently, large quantities of produced PG are stored in surface stockpiles that occupy extensive land areas and may pose a significant risk of ecological contamination to the surroundings. Researchers have shown growing interest in addressing the worldwide accumulation of this waste material. To gain a comprehensive understanding of the environmental impact of phosphogypsum, it is crucial to explore its properties (e.g., chemistry, mineralogy, radioactivity), and how it interacts with the surrounding environment, enabling well-informed decisions decision regarding its management and its valorization. In this review, we will i) explore the chemical, radiological and mineralogical characteristics of PG; ii) discuss the environmental concerns related to land discharge and sea disposal; and iii) examine the latest advancements in various valorization techniques developed including agriculture, REE extraction, environmental application, chemical and thermal transformation, and also construction sector. Outlining their limitations and challenges restrict in the global variability of phosphogypsum (PG), technical and economic limitations, and the potential for secondary pollution in select valorization approaches. This requires a thorough assessment and comparison with conventional disposal alternatives.

Toxic, genotoxic, mutagenic, and bioaccumulative effects of metal mixture from settleable particulate matter on American bullfrog tadpoles (Lithobates catesbeianus)

Amphibians are more susceptible to environmental stressors than other vertebrates due to their semipermeable skin and physiological adaptations to living in very specific microhabitats. Therefore, the aim of the present study was to investigate the effects of a metal mixture from settleable particulate matter (SePM) released from metallurgical industries on Lithobates catesbeianus tadpoles. Endpoints analyzed included metal bioconcentration, morphological (biometrical indices), hematological parameters (hemoglobin and blood cell count), and erythrocyte DNA damage (genotoxicity and mutagenicity). American bullfrog tadpoles (Gosner's stage 25) were kept under control condition (no contaminant addition) or exposed to a sub-lethal and environmentally relevant concentration (1 g.L-1) of SePM for 96 h. Tadpoles exposed to SePM exhibited elevated whole blood levels of Fe56, AL, Sn, Pb, Zn, Cr, Cu, Ti, Rb, V, Ce, La, Ag, As. SePM-exposed tadpoles showed a significant decrease in condition factor (12%) and increases in hepatosomatic index (25%), hemoglobin concentration (17%), and total leukocytes (82%), thrombocytes (90%), and monocytes (78%) abundance. In addition, exposed tadpoles showed higher MN and ENAs (340 and 140%, respectively) frequencies, and erythrocyte DNA damage with approximately 1.2- to 1.8-fold increases in comet parameters. Taken together, these results suggest that the multimetal mixture found in SePM is potentially genotoxic and mutagenic to L. catesbeianus tadpoles, induces stress associated with hematological changes, and negatively affects growth. Although such contamination occurs at sublethal levels, regulatory standards are needed to control the emission of SePM and protect amphibian populations.

Functional Ag-EDTA-modified MnO2 nanocoral reef for rapid removal of hazardous copper from wastewater

A novel MnO2@EDTA-Ag nanocoral reef was constructed via a simplified redox reaction followed by EDTA and Ag nanoparticles impregnation to capture hazardous copper (II) from wastewater. A comprehensive characterization of the synthesized materials was conducted. The morphology of MnO2@EDTA-Ag in the form of a nanocoral reef was constructed of two-dimensional nanoplatelets and nanorod-like nanostructures. The optimal adsorption conditions proposed by the Plackett-Burman design (PBD) that would provide a removal % of 99.95 were pH 5.5, a contact time of 32.0 min, a Cu(II) concentration of 11.2 mg L-1, an adsorbent dose of 0.05 g, and a temperature of 40.3 °C. The loading of Ag nanoparticles onto MnO2@EDTA improved the adsorption capability of MnO2@EDTA-Ag. Additionally, the recyclability of MnO2@EDTA-Ag nanocoral reef was maintained at 80% after three adsorption-desorption cycles, and there was no significant change in the XRD analysis before and after the recycling process, implying its stability. It was found that nanocoral reef-assisted EDTA formed a chelation/complexation reaction between COO- groups and C-N bonds of EDTA with Cu(II) ions. In addition, X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) analysis proved the synergistic effect of the electrostatic interaction and chelation/complexation was responsible for the removal mechanism of Cu(II). Also, the results demonstrated no significant variation in MnO2@EDTA-Ag removal efficiency for all the tested real water samples, revealing its efficacy in wastewater treatment. Therefore, the current study suggests that MnO2@EDTA-Ag has substantial potential to be used as a feasible adsorbent for probable hazardous metals remediation.

Unlocking sustainable solutions: controlled Cu2+ dosing enables efficient recovery and reuse of high-purity copper pyrophosphate from electroplating wastewater

The electroplating process of copper pyrophosphate (Cu2P2O7) results in the production of a large volume of wastewater that contains a high concentration of copper (Cu). Currently, conventional lime precipitation creates a substantial amount of secondary pollution, which adds extra economic and environmental burdens. In this study, we suggest a straightforward method for on-site recovery of Cu from Cu2P2O7 electroplating wastewater. By optimizing various parameters, characterizing the resulting product, assessing its electroplating capabilities, and analyzing the speciation during the reaction, we comprehensively investigated the feasibility and mechanism of this technique. The results demonstrated that, under the optimal conditions (Cu/P molar ratio of 0.96, pH of 5.0, and a reaction time of 5.0 min), the concentration of residual Cu remained stable between 22.2 and 27.7 mg/L, even when the initial Cu concentrations varied. The addition of Cu triggered a series of hydrolysis and ionization reactions, primarily leading to the formation of Cu2P2O7·3H2O. The harvested Cu2P2O7·3H2O proved to be suitable for practical electroplating applications, exhibiting comparable performance to commercially available Cu2P2O7·3H2O. This demonstrates the feasibility of recovering high-purity Cu2P2O7·3H2O from copper electroplating wastewater, offering a promising approach for on-site copper reuse and concurrently reducing the demand for natural copper resources. Furthermore, this approach significantly reduces the generation of solid waste, aligning with the principles of sustainable development.

Compositional transformation of Ni2+ and Fe0 during the removal of Ni2+ by nanoscale zero-valent iron and the implications to groundwater remediation

The use of nanoscale zero-valent iron (nZVI) to remove heavy metal ions like Ni2+ from groundwater has been extensively studied; however, the compositional transformation of the Ni2+ and Fe0 during the removal is not clearly comprehensible. This study provides an insight into the componential, structural, and morphological transformations of Ni2+ and Fe0 at a solid-liquid interface using various characterization devices. The underlying mechanism of transformation was investigated along with the toxicity/impact of the transformed products on the groundwater ecosystem. The results indicated that Fe0 is transformed into lath-like lepidocrocite (γ-FeOOH), twin-crystal goethite (α-FeOOH), and spherical magnetite (Fe3O4), while Ni2+ is converted into Fe0.7Ni0.3 alloy and Fe-Ni composite (trevorite - NiFe2O4) with a fold-fan morphology. The Fe0 transformation mechanism includes the redox of Fe0 with Ni2+, H2O, and dissolved oxygen, the combination of Fe2+ and OH- produced by Fe0 corrosion to amorphous ferrihydrite, and the further mineralogical transformation to Fe oxides with the aid of Fe2+ adsorbed on ferrihydrite. The conversion of Ni2+ is accomplished by reduction by Fe0 and surface coordination with Fe oxides. Compared with Ni2+ and Fe0, the toxicity and bioavailability of the transformed products are significantly reduced, hence conducive to the application of zero-valent iron technology in groundwater remediation.

Metallic trace element contamination of the giant clam Tridacna maxima in French Polynesia

This study is a first assessment of Metallic Trace Elements (MTE) contamination of four lagoons in French Polynesia, chosen because their main anthropic uses are potential sources of MTE (military, agriculture, maritime). We used the giant clam Tridacna maxima as a biointegrator of fifteen MTE to assess the environmental footprint of human activities. The study of organotropism showed that not only the kidney but also the gonad and digestive system (GDS) are accumulator organs of interest for ETM biomonitoring. This result confirms that heterotrophic feeding is the pathway of ETM accumulation. Here, T. maxima appeared to be a super-accumulator of Ni (2700 ppm.dw), but also revealed at Tubuai (As, Fe, Mn) and Arutua (Cd, Zn) the environmental footprint of agricultural and maritime activities. The concentration of Cd recorded in Arutua (5 ppm.dw) both in KID and GDS, also underline the need for better control of effluents resulting from human activities.

Heavy Metal Pollution in the Environment and Its Impact on Health: Exploring Green Technology for Remediation

Along with expanding urbanization and industrialization, environmental pollution which negatively affects the surroundings, has been rising quickly. As a result, induces heavy metal contamination which poses a serious threat to living organisms of aquatic and soil ecosystems. Therefore, they are a need to ameliorate the effects cost by cost pollution on the environment. In this review, we explore methods employed to mitigate the effects caused by heavy metals on the environment. Many techniques employed to manage environmental pollution are tedious and very costly, necessitating the use of alternative management strategies to resolve this challenge. In this concept, bioremediation is viewed as a future technique, due to its environmental friendliness and cost-effective measures aligned with sustainable or climate-smart agriculture to manage contaminants in the environment. The technique involves the use of living entities such as bacteria, fungi, and plants to deteriorate toxic substances from the rhizosphere. Currently, bioremediation is thought to be the most practical, dependable, environmentally benign, and long-lasting solution. Although bioremediation involves different techniques, they are still a need to find the most efficient method for removing toxic substances from the environment. This review focuses on the origins of heavy metal pollution, delves into cost-effective and green technological approaches for eliminating heavy metal pollutants from the environment, and discusses the impact of these pollutants on human health.

Iron-loaded carbon black prepared via chemical vapor deposition as an efficient peroxydisulfate activator for the removal of rhodamine B from water

The excessive use of organic pollutants like organic dyes, which enter the water environment, has led to a significant environmental problem. Finding an efficient method to degrade these pollutants is urgent due to their detrimental effects on aquatic organisms and human health. Carbon-based catalysts are emerging as highly promising and efficient alternatives to metal catalysts in Fenton-like systems. They serve as persulfate activators, effectively eliminating recalcitrant organic pollutants from wastewater. In this study, iron-loaded carbon black (Fe-CB) was synthesized from tire waste using chemical vapor deposition (CVD). Fe-CB exhibited high efficiency as an activator of peroxydisulfate (PDS), facilitating the effective degradation and mineralization of rhodamine B (RhB) in water. A batch experiment and series characterization were conducted to study the morphology, composition, stability, and catalytic activity of Fe-CB in a Fenton-like system. The results showed that, at circumneutral pH, the degradation and mineralization efficiency of 20 mg L-1 RhB reached 92% and 48% respectively within 60 minutes. Fe-CB exhibited excellent reusability and low metal leaching over five cycles while maintaining almost the same efficiency. The degradation kinetics of RhB was found to follow a pseudo-first-order model. Scavenging tests revealed that the dominant role was played by sulfate (SO4-˙) and superoxide (O2-˙) radicals, whereas hydroxyl radicals (OH˙) and singlet oxygen (1O2) played a minor role in the degradation process. This study elucidates the detailed mechanism of PDS activation by Fe-CB, resulting in the generation of reactive oxygen species. It highlights the effectiveness of Fe-CB/PDS in a Fenton-like system for the treatment of water polluted with organic dye contaminants. The research provides valuable insights into the potential application of carbon black derived from tire waste for environmental remediation.