51
|
Fumeaux N, Briand D. Zinc hybrid sintering for printed transient sensors and wireless electronics. NPJ FLEXIBLE ELECTRONICS 2023; 7:14. [PMID: 38665150 PMCID: PMC11041761 DOI: 10.1038/s41528-023-00249-0] [Citation(s) in RCA: 2] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 11/28/2022] [Accepted: 02/28/2023] [Indexed: 04/28/2024]
Abstract
Transient electronics offer a promising solution for reducing electronic waste and for use in implantable bioelectronics, yet their fabrication remains challenging. We report on a scalable method that synergistically combines chemical and photonic mechanisms to sinter printed Zn microparticles. Following reduction of the oxide layer using an acidic solution, zinc particles are agglomerated into a continuous layer using a flash lamp annealing treatment. The resulting sintered Zn patterns exhibit electrical conductivity values as high as 5.62 × 106 S m-1. The electrical conductivity and durability of the printed zinc traces enable the fabrication of biodegradable sensors and LC circuits: temperature, strain, and chipless wireless force sensors, and radio-frequency inductive coils for remote powering. The process allows for reduced photonic energy to be delivered to the substrate and is compatible with temperature-sensitive polymeric and cellulosic substrates, enabling new avenues for the additive manufacturing of biodegradable electronics and transient implants.
Collapse
Affiliation(s)
- N. Fumeaux
- Soft Transducers Laboratory, Ecole Polytechnique Fédérale de Lausanne (EPFL), Rue de la Maladière 71b, CH-2000 Neuchâtel, Switzerland
| | - D. Briand
- Soft Transducers Laboratory, Ecole Polytechnique Fédérale de Lausanne (EPFL), Rue de la Maladière 71b, CH-2000 Neuchâtel, Switzerland
| |
Collapse
|
52
|
Li Q, Bai F, Sun J, Zhou X, Yuan W, Lin J, Zhang KQ, Li G, Liu Z. Bubble-blowing-inspired sub-micron thick freestanding silk films for programmable electronics. NANOSCALE 2023; 15:3796-3804. [PMID: 36648031 DOI: 10.1039/d2nr05490f] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/17/2023]
Abstract
Thin film electronics that are capable of deforming and interfacing with nonplanar surfaces have attracted widespread interest in wearable motion detection or physiological signal recording due to their light weight, low stiffness, and high conformality. However, it is still a challenge to fabricate freestanding thin film substrates or matrices with only sub-micron thickness in a simple way, especially for those materials with metastable conformations, like regenerated silk protein. Herein, we developed a dip-coating method for the fabrication of sub-micron thick freestanding silk films inspired by blowing soap bubbles. Using a closed-loop frame to dip-coat in a concentrated silk fibroin aqueous solution, the substrate-free silk films with a thickness as low as hundreds of nanometres (∼150 nm) can be easily obtained after solvent evaporation. The silk films have extremely smooth surfaces (Rq < 3 nm) and can be tailored with different geometric shapes. The naturally dried silk films possess random coil dominated uncrystallized secondary structures, exhibiting high modulation ability and adaptability, which can be conformally attached on wrinkled skin or wrapped on human hair. Considering the methodological advantages and the unique properties of the obtained sub-micron thick silk films, several thin film based programmable electronics including transient/durable circuits, skin electrodes, transferred skin light-emitting devices and injectable electronics are successfully demonstrated after being deposited with gold or conducting polymer layers. This research provides a new avenue for preparing freestanding thin polymer films, showing great promise for developing thin film electronics in wearable and biomedical applications.
Collapse
Affiliation(s)
- Qingsong Li
- CAS Key Laboratory of Human-Machine Intelligence-Synergy Systems, Shenzhen Institute of Advanced Technology, Chinese Academy of Sciences (CAS), Shenzhen 518055, China.
| | - Fengjiao Bai
- National Engineering Laboratory for Modern Silk, College of Textile and Clothing Engineering, Soochow University, Suzhou 215123, China.
| | - Jing Sun
- CAS Key Laboratory of Human-Machine Intelligence-Synergy Systems, Shenzhen Institute of Advanced Technology, Chinese Academy of Sciences (CAS), Shenzhen 518055, China.
| | - Xiaomeng Zhou
- CAS Key Laboratory of Human-Machine Intelligence-Synergy Systems, Shenzhen Institute of Advanced Technology, Chinese Academy of Sciences (CAS), Shenzhen 518055, China.
| | - Wei Yuan
- Printable Electronics Research Centre, Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, Suzhou, 215123, China
| | - Jin Lin
- CAS Key Laboratory of Human-Machine Intelligence-Synergy Systems, Shenzhen Institute of Advanced Technology, Chinese Academy of Sciences (CAS), Shenzhen 518055, China.
| | - Ke-Qin Zhang
- National Engineering Laboratory for Modern Silk, College of Textile and Clothing Engineering, Soochow University, Suzhou 215123, China.
| | - Guanglin Li
- CAS Key Laboratory of Human-Machine Intelligence-Synergy Systems, Shenzhen Institute of Advanced Technology, Chinese Academy of Sciences (CAS), Shenzhen 518055, China.
| | - Zhiyuan Liu
- CAS Key Laboratory of Human-Machine Intelligence-Synergy Systems, Shenzhen Institute of Advanced Technology, Chinese Academy of Sciences (CAS), Shenzhen 518055, China.
| |
Collapse
|
53
|
Flimelová M, Ryabchikov YV, Behrends J, Bulgakova NM. Environmentally Friendly Improvement of Plasmonic Nanostructure Functionality towards Magnetic Resonance Applications. NANOMATERIALS (BASEL, SWITZERLAND) 2023; 13:764. [PMID: 36839132 PMCID: PMC9965577 DOI: 10.3390/nano13040764] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 01/27/2023] [Revised: 02/10/2023] [Accepted: 02/11/2023] [Indexed: 06/18/2023]
Abstract
Plasmonic nanostructures have attracted a broad research interest due to their application perspectives in various fields such as biosensing, catalysis, photovoltaics, and biomedicine. Their synthesis by pulsed laser ablation in pure water enables eliminating various side effects originating from chemical contamination. Another advantage of pulsed laser ablation in liquids (PLAL) is the possibility to controllably produce plasmonic nanoparticles (NPs) in combination with other plasmonic or magnetic materials, thus enhancing their functionality. However, the PLAL technique is still challenging in respect of merging metallic and semiconductor specific features in nanosized objects that could significantly broaden application areas of plasmonic nanostructures. In this work, we performed synthesis of hybrid AuSi NPs with novel modalities by ultrashort laser ablation of bulk gold in water containing silicon NPs. The Au/Si atomic ratio in the nanohybrids was finely varied from 0.5 to 3.5 when changing the initial Si NPs concentration in water from 70 µg/mL to 10 µg/mL, respectively, without requiring any complex chemical procedures. It has been found that the laser-fluence-insensitive silicon content depends on the mass of nanohybrids. A high concentration of paramagnetic defects (2.2·× 1018 spin/g) in polycrystalline plasmonic NPs has been achieved. Our findings can open further prospects for plasmonic nanostructures as contrast agents in optical and magnetic resonance imaging techniques, biosensing, and cancer theranostics.
Collapse
Affiliation(s)
- Miroslava Flimelová
- HiLASE Centre, Institute of Physics of the Czech Academy of Sciences, Za Radnicí 828, 25241 Dolní Břežany, Czech Republic
| | - Yury V. Ryabchikov
- HiLASE Centre, Institute of Physics of the Czech Academy of Sciences, Za Radnicí 828, 25241 Dolní Břežany, Czech Republic
| | - Jan Behrends
- Berlin Joint EPR Lab., Fachbereich Physik, Freie Universität Berlin, Arnimallee 14, 14195 Berlin, Germany
| | - Nadezhda M. Bulgakova
- HiLASE Centre, Institute of Physics of the Czech Academy of Sciences, Za Radnicí 828, 25241 Dolní Břežany, Czech Republic
| |
Collapse
|
54
|
Song JH, Park J, Kim SH, Kwak J. Vitamin C-Induced Enhanced Performance of PEDOT:PSS Thin Films for Eco-Friendly Transient Thermoelectrics. ACS APPLIED MATERIALS & INTERFACES 2023; 15:2852-2860. [PMID: 36608257 DOI: 10.1021/acsami.2c17263] [Citation(s) in RCA: 2] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/17/2023]
Abstract
Conjugated polymer-based energy-harvesting devices hold distinctive advantages in terms of low toxicity, high flexibility, and capability of large-area integration at low cost for sustainable development. An organic thermoelectric (OTE) device has been considered one of the promising energy-harvesting candidates in recent years because it can efficiently convert low-temperature waste heat into electricity over its inorganic counterparts. However, a cruel irony is that environmentally toxic solvents and acids are utilized for fabrication and performance improvement of the OTE devices, retarding the development and use of genuinely green energy-harvesting. Here, we present eco-friendly, non-toxic strategies for a poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)-based high-performance OTE device by incorporating a nature-abundant material, vitamin C (VC), as an additive. We found that the intrinsic polar nature and reducing ability of VC induce synergy effects of microstructure alignment with PSS removal and dedoping of PEDOT, leading to simultaneous enhancement of the electrical conductivity (>400 S cm-1) and the Seebeck coefficient (>30 μV K-1) and a resultant high thermoelectric power factor of 51.8 μW m-1 K-2. In addition, inspired by the eco-friendly fabrication process, we further demonstrated a transient OTE device, which can be fully degraded with naturally occurring substances, by fabricating it on a bio-based cellulose acetate substrate. We believe that our eco-friendly strategies from fabrication to disposal of the OTE can be applied to the development of high-performance, wearable, and bio-compatible OTE devices with minimal waste and further trigger the research on genuinely green thermal energy harvesting.
Collapse
Affiliation(s)
- Jeong Han Song
- Department of Electrical and Computer Engineering, and Inter-university Semiconductor Research Center, and Soft Foundry Institute, Seoul National University, 1, Gwanak-ro, Gwanak-gu, Seoul 08826, Republic of Korea
| | - Juhyung Park
- Department of Electrical and Computer Engineering, and Inter-university Semiconductor Research Center, and Soft Foundry Institute, Seoul National University, 1, Gwanak-ro, Gwanak-gu, Seoul 08826, Republic of Korea
| | - Sun Hong Kim
- Department of Electrical and Computer Engineering, and Inter-university Semiconductor Research Center, and Soft Foundry Institute, Seoul National University, 1, Gwanak-ro, Gwanak-gu, Seoul 08826, Republic of Korea
| | - Jeonghun Kwak
- Department of Electrical and Computer Engineering, and Inter-university Semiconductor Research Center, and Soft Foundry Institute, Seoul National University, 1, Gwanak-ro, Gwanak-gu, Seoul 08826, Republic of Korea
| |
Collapse
|
55
|
Kim KS, Maeng WY, Kim S, Lee G, Hong M, Kim GB, Kim J, Kim S, Han S, Yoo J, Lee H, Lee K, Koo J. Isotropic conductive paste for bioresorbable electronics. Mater Today Bio 2023; 18:100541. [PMID: 36647537 PMCID: PMC9840151 DOI: 10.1016/j.mtbio.2023.100541] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/06/2022] [Revised: 12/18/2022] [Accepted: 01/02/2023] [Indexed: 01/05/2023] Open
Abstract
Bioresorbable implantable medical devices can be employed in versatile clinical scenarios that burden patients with complications and surgical removal of conventional devices. However, a shortage of suitable electricalinterconnection materials limits the development of bioresorbable electronic systems. Therefore, this study highlights a highly conductive, naturally resorbable paste exhibiting enhanced electrical conductivity and mechanical stability that can solve the existing problems of bioresorbable interconnections. Multifaceted experiments on electrical and physical properties were used to optimize the composition of pastes containing beeswax, submicron tungstenparticles, and glycofurol. These pastes embody isotropic conductive paths for three-dimensional interconnects and function as antennas, sensors, and contact pads for bioresorbable electronic devices. The degradation behavior in aqueous solutions was used to assess its stability and ability to retain electrical conductance (∼7 kS/m) and structural form over the requisite dissolution period. In vitro and in vivo biocompatibility tests clarified the safety of the paste as an implantable material.
Collapse
Affiliation(s)
- Kyung Su Kim
- School of Biomedical Engineering, Korea University, Seoul, 02841, South Korea,Interdisciplinary Program in Precision Public Health, Korea University, Seoul, 02841, South Korea
| | - Woo-Youl Maeng
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL, 60208, USA
| | - Seongchan Kim
- Biomaterials Research Center, Biomedical Research Division, Korea Institute of Science and Technology (KIST), Seoul, 02792, South Korea
| | - Gyubok Lee
- Department of Applied Bioengineering, Graduate School of Convergence Science and Technology, Seoul National University, Seoul, 08826, South Korea
| | - Minki Hong
- School of Biomedical Engineering, Korea University, Seoul, 02841, South Korea,Interdisciplinary Program in Precision Public Health, Korea University, Seoul, 02841, South Korea
| | - Ga-been Kim
- School of Biomedical Engineering, Korea University, Seoul, 02841, South Korea,Biomaterials Research Center, Biomedical Research Division, Korea Institute of Science and Technology (KIST), Seoul, 02792, South Korea
| | - Jaewon Kim
- School of Biomedical Engineering, Korea University, Seoul, 02841, South Korea
| | - Sungeun Kim
- School of Biomedical Engineering, Korea University, Seoul, 02841, South Korea,Interdisciplinary Program in Precision Public Health, Korea University, Seoul, 02841, South Korea
| | - Seunghun Han
- School of Biomedical Engineering, Korea University, Seoul, 02841, South Korea,Interdisciplinary Program in Precision Public Health, Korea University, Seoul, 02841, South Korea
| | - Jaeyoung Yoo
- Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, 34141, South Korea
| | - Hyojin Lee
- Biomaterials Research Center, Biomedical Research Division, Korea Institute of Science and Technology (KIST), Seoul, 02792, South Korea,Division of Bio-Medical Science & Technology, KIST School, Korea University of Science and Technology (UST), Seoul, 02792, South Korea
| | - Kangwon Lee
- Department of Applied Bioengineering, Graduate School of Convergence Science and Technology, Seoul National University, Seoul, 08826, South Korea,Research Institute for Convergence Science, Seoul National University, Seoul, 08826, South Korea
| | - Jahyun Koo
- School of Biomedical Engineering, Korea University, Seoul, 02841, South Korea,Interdisciplinary Program in Precision Public Health, Korea University, Seoul, 02841, South Korea,Corresponding author.. School of Biomedical Engineering, Korea University, Seoul, 02841, South Korea.
| |
Collapse
|
56
|
Feng H, Lou W, He B, Lv S, Su W. Information self-destruction module design based on micro thermoelectric power generation and energetic materials. ISA TRANSACTIONS 2023; 132:573-581. [PMID: 35786517 DOI: 10.1016/j.isatra.2022.06.019] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 02/16/2022] [Revised: 06/15/2022] [Accepted: 06/15/2022] [Indexed: 06/15/2023]
Abstract
Information self-destruction modules (ISDMs) play a vital role in the information security area. In this paper, an ISDM based on the integration of a micro-thermoelectric generation mechanism (M-TEGM) with energetic materials (EMs) is proposed. On the basis of energy conversion relationship, an open-loop electromotive force is induced, and this energy will drive the EMs to release the detonation wave and realize information storage module self-destruction. During the tests, under the temperature difference (100 K), the open-loop electromotive force (3.86 V) is induced by the M-TEGM and can drive the EMs (0.37 mg copper azide) to generate a detonation wave (GPa) in 3.4 μs, which can physically destroy the information storage modules. This ISDM has advantages that include rapid response times, low drive energy compared with traditional information security technology.
Collapse
Affiliation(s)
- Hengzhen Feng
- The school of Mechatronical Engineering, Beijing Institute of Technology, 100081, Beijing, China.
| | - Wenzhong Lou
- The school of Mechatronical Engineering, Beijing Institute of Technology, 100081, Beijing, China.
| | - Bo He
- The school of Mechatronical Engineering, Beijing Institute of Technology, 100081, Beijing, China.
| | - Sining Lv
- The school of Mechatronical Engineering, Beijing Institute of Technology, 100081, Beijing, China.
| | - Wenting Su
- The school of Mechatronical Engineering, Beijing Institute of Technology, 100081, Beijing, China.
| |
Collapse
|
57
|
Biodegradable Polymers in Triboelectric Nanogenerators. Polymers (Basel) 2022; 15:polym15010222. [PMID: 36616571 PMCID: PMC9823430 DOI: 10.3390/polym15010222] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/30/2022] [Revised: 12/23/2022] [Accepted: 12/28/2022] [Indexed: 01/03/2023] Open
Abstract
Triboelectric nanogenerators (TENGs) have attracted much attention because they not only efficiently harvest energy from the surrounding environment and living organisms but also serve as multifunctional sensors toward the detection of various chemical and physical stimuli. In particular, biodegradable TENG (BD-TENG) represents an emerging type of self-powered device that can be degraded, either in physiological environments as an implantable power source without the necessity of second surgery for device retrieval, or in the ambient environment to minimize associated environmental pollution. Such TENGs or TNEG-based self-powered devices can find important applications in many scenarios, such as tissue regeneration, drug release, pacemakers, etc. In this review, the recent progress of TENGs developed on the basis of biodegradable polymers is comprehensively summarized. Material strategies and fabrication schemes of biodegradable and self-powered devices are thoroughly introduced according to the classification of plant-degradable polymer, animal-degradable polymer, and synthetic degradable polymer. Finally, current problems, challenges, and potential opportunities for the future development of BD-TENGs are discussed. We hope this work may provide new insights for modulating the design of BD-TNEGs that can be beneficial for both environmental protection and healthcare.
Collapse
|
58
|
Dulal M, Afroj S, Ahn J, Cho Y, Carr C, Kim ID, Karim N. Toward Sustainable Wearable Electronic Textiles. ACS NANO 2022; 16:19755-19788. [PMID: 36449447 PMCID: PMC9798870 DOI: 10.1021/acsnano.2c07723] [Citation(s) in RCA: 20] [Impact Index Per Article: 10.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/03/2022] [Accepted: 11/10/2022] [Indexed: 06/06/2023]
Abstract
Smart wearable electronic textiles (e-textiles) that can detect and differentiate multiple stimuli, while also collecting and storing the diverse array of data signals using highly innovative, multifunctional, and intelligent garments, are of great value for personalized healthcare applications. However, material performance and sustainability, complicated and difficult e-textile fabrication methods, and their limited end-of-life processability are major challenges to wide adoption of e-textiles. In this review, we explore the potential for sustainable materials, manufacturing techniques, and their end-of-the-life processes for developing eco-friendly e-textiles. In addition, we survey the current state-of-the-art for sustainable fibers and electronic materials (i.e., conductors, semiconductors, and dielectrics) to serve as different components in wearable e-textiles and then provide an overview of environmentally friendly digital manufacturing techniques for such textiles which involve less or no water utilization, combined with a reduction in both material waste and energy consumption. Furthermore, standardized parameters for evaluating the sustainability of e-textiles are established, such as life cycle analysis, biodegradability, and recyclability. Finally, we discuss the current development trends, as well as the future research directions for wearable e-textiles which include an integrated product design approach based on the use of eco-friendly materials, the development of sustainable manufacturing processes, and an effective end-of-the-life strategy to manufacture next generation smart and sustainable wearable e-textiles that can be either recycled to value-added products or decomposed in the landfill without any negative environmental impacts.
Collapse
Affiliation(s)
- Marzia Dulal
- Centre
for Print Research (CFPR), University of
the West of England, Frenchay Campus, BristolBS16 1QY, United
Kingdom
| | - Shaila Afroj
- Centre
for Print Research (CFPR), University of
the West of England, Frenchay Campus, BristolBS16 1QY, United
Kingdom
| | - Jaewan Ahn
- Department
of Materials Science and Engineering, Korea
Advanced Institute of Science and Technology (KAIST), Daejeon34141, Republic of Korea
| | - Yujang Cho
- Department
of Materials Science and Engineering, Korea
Advanced Institute of Science and Technology (KAIST), Daejeon34141, Republic of Korea
| | - Chris Carr
- Clothworkers’
Centre for Textile Materials Innovation for Healthcare, School of
Design, University of Leeds, LeedsLS2 9JT, United Kingdom
| | - Il-Doo Kim
- Department
of Materials Science and Engineering, Korea
Advanced Institute of Science and Technology (KAIST), Daejeon34141, Republic of Korea
| | - Nazmul Karim
- Centre
for Print Research (CFPR), University of
the West of England, Frenchay Campus, BristolBS16 1QY, United
Kingdom
| |
Collapse
|
59
|
Sharfstein ST. Bio-hybrid electronic and photonic devices. Exp Biol Med (Maywood) 2022; 247:2128-2141. [PMID: 36533579 PMCID: PMC9837307 DOI: 10.1177/15353702221144087] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/23/2022] Open
Abstract
Bio-hybrid devices, combining electronic and photonic components with cells, tissues, and organs, hold potential for advancing our understanding of biology, physiology, and pathologies and for treating a wide range of conditions and diseases. In this review, I describe the devices, materials, and technologies that enable bio-hybrid devices and provide examples of their utilization at multiple biological scales ranging from the subcellular to whole organs. Finally, I describe the outcomes of a National Science Foundation (NSF)-funded workshop envisioning potential applications of these technologies to improve health outcomes and quality of life.
Collapse
|
60
|
Suresh Khurd A, Kandasubramanian B. A systematic review of cellulosic material for green electronics devices. CARBOHYDRATE POLYMER TECHNOLOGIES AND APPLICATIONS 2022. [DOI: 10.1016/j.carpta.2022.100234] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/28/2022] Open
|
61
|
Haskew MJ, Nikman S, O'Sullivan CE, Galeb HA, Halcovitch NR, Hardy JG, Murphy ST. Mg/Zn metal‐air primary batteries using silk fibroin‐ionic liquid polymer electrolytes. NANO SELECT 2022. [DOI: 10.1002/nano.202200200] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/17/2022] Open
Affiliation(s)
- Mathew J. Haskew
- School of Engineering Lancaster University Bailrigg Lancaster UK
- Department of Chemistry Lancaster University Faraday Building Bailrigg Lancaster UK
| | - Shahin Nikman
- Department of Chemistry Lancaster University Faraday Building Bailrigg Lancaster UK
| | - Carys E. O'Sullivan
- Department of Chemistry Lancaster University Faraday Building Bailrigg Lancaster UK
| | - Hanaa A. Galeb
- Department of Chemistry Lancaster University Faraday Building Bailrigg Lancaster UK
- Department of Chemistry Science and Arts College, Rabigh Campus King Abdulaziz University Jeddah Saudi Arabia
| | - Nathan R. Halcovitch
- Department of Chemistry Lancaster University Faraday Building Bailrigg Lancaster UK
| | - John G. Hardy
- Department of Chemistry Lancaster University Faraday Building Bailrigg Lancaster UK
- Materials Science Institute Lancaster University Faraday Building, John Creed Avenue Bailrigg Lancaster UK
| | - Samuel T. Murphy
- School of Engineering Lancaster University Bailrigg Lancaster UK
- Materials Science Institute Lancaster University Faraday Building, John Creed Avenue Bailrigg Lancaster UK
| |
Collapse
|
62
|
Lee S, M Silva S, Caballero Aguilar LM, Eom T, Moulton SE, Shim BS. Biodegradable bioelectronics for biomedical applications. J Mater Chem B 2022; 10:8575-8595. [PMID: 36214325 DOI: 10.1039/d2tb01475k] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/14/2022]
Abstract
Biodegradable polymers have been widely used in tissue engineering with the potential to be replaced by regenerative tissue. While conventional bionic interfaces are designed to be implanted in living tissue and organs permanently, biocompatible and biodegradable electronic materials are now progressing a paradigm shift towards transient and regenerative bionic engineering. For example, biodegradable bioelectronics can monitor physiologies in a body, transiently rehabilitate disease symptoms, and seamlessly form regenerative interfaces from synthetic electronic devices to tissues by reducing inflammatory foreign-body responses. Conventional electronic materials have not readily been considered biodegradable. However, several strategies have been adopted for designing electroactive and biodegradable materials systems: (1) conductive materials blended with biodegradable components, (2) molecularly engineered conjugated polymers with biodegradable moieties, (3) naturally derived conjugated biopolymers, and (4) aqueously dissolvable metals with encapsulating layers. In this review, we endeavor to present the technical bridges from electrically active and biodegradable material systems to edible and biodegradable electronics as well as transient bioelectronics with pre-clinical bio-instrumental applications, including biodegradable sensors, neural and tissue engineering, and intelligent drug delivery systems.
Collapse
Affiliation(s)
- Seunghyeon Lee
- Program in Biomedical Science & Engineering, Inha University, 100, Inha-ro, Michuhol-gu, Incheon, Republic of Korea. .,Department of Chemical Engineering, Inha University, 100, Inha-ro, Michuhol-gu, Incheon, Republic of Korea
| | - Saimon M Silva
- ARC Centre of Excellence for Electromaterials Science, School of Science, Computing and Engineering Technologies, Swinburne University of Technology, Melbourne, Victoria 3122, Australia.,Iverson Health Innovation Research Institute, Swinburne University of Technology, Melbourne, Victoria 3122, Australia. .,The Aikenhead Centre for Medical Discovery, St Vincent's Hospital Melbourne, Melbourne, Victoria 3065, Australia
| | - Lilith M Caballero Aguilar
- ARC Centre of Excellence for Electromaterials Science, School of Science, Computing and Engineering Technologies, Swinburne University of Technology, Melbourne, Victoria 3122, Australia.,Iverson Health Innovation Research Institute, Swinburne University of Technology, Melbourne, Victoria 3122, Australia. .,The Aikenhead Centre for Medical Discovery, St Vincent's Hospital Melbourne, Melbourne, Victoria 3065, Australia
| | - Taesik Eom
- Program in Biomedical Science & Engineering, Inha University, 100, Inha-ro, Michuhol-gu, Incheon, Republic of Korea. .,Department of Chemical Engineering, Inha University, 100, Inha-ro, Michuhol-gu, Incheon, Republic of Korea
| | - Simon E Moulton
- ARC Centre of Excellence for Electromaterials Science, School of Science, Computing and Engineering Technologies, Swinburne University of Technology, Melbourne, Victoria 3122, Australia.,Iverson Health Innovation Research Institute, Swinburne University of Technology, Melbourne, Victoria 3122, Australia. .,The Aikenhead Centre for Medical Discovery, St Vincent's Hospital Melbourne, Melbourne, Victoria 3065, Australia
| | - Bong Sup Shim
- Program in Biomedical Science & Engineering, Inha University, 100, Inha-ro, Michuhol-gu, Incheon, Republic of Korea. .,Department of Chemical Engineering, Inha University, 100, Inha-ro, Michuhol-gu, Incheon, Republic of Korea
| |
Collapse
|
63
|
Shin YK, Shin Y, Lee JW, Seo MH. Micro-/Nano-Structured Biodegradable Pressure Sensors for Biomedical Applications. BIOSENSORS 2022; 12:952. [PMID: 36354461 PMCID: PMC9687959 DOI: 10.3390/bios12110952] [Citation(s) in RCA: 4] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 09/23/2022] [Revised: 10/24/2022] [Accepted: 10/27/2022] [Indexed: 06/16/2023]
Abstract
The interest in biodegradable pressure sensors in the biomedical field is growing because of their temporary existence in wearable and implantable applications without any biocompatibility issues. In contrast to the limited sensing performance and biocompatibility of initially developed biodegradable pressure sensors, device performances and functionalities have drastically improved owing to the recent developments in micro-/nano-technologies including device structures and materials. Thus, there is greater possibility of their use in diagnosis and healthcare applications. This review article summarizes the recent advances in micro-/nano-structured biodegradable pressure sensor devices. In particular, we focus on the considerable improvement in performance and functionality at the device-level that has been achieved by adapting the geometrical design parameters in the micro- and nano-meter range. First, the material choices and sensing mechanisms available for fabricating micro-/nano-structured biodegradable pressure sensor devices are discussed. Then, this is followed by a historical development in the biodegradable pressure sensors. In particular, we highlight not only the fabrication methods and performances of the sensor device, but also their biocompatibility. Finally, we intoduce the recent examples of the micro/nano-structured biodegradable pressure sensor for biomedical applications.
Collapse
Affiliation(s)
- Yoo-Kyum Shin
- Department of Information Convergence Engineering, Pusan National University, 49 Busandaehak-ro, Mulgeum-eup, Yangsan-si 50612, Gyeongsangnam-do, Korea
| | - Yujin Shin
- Department of Materials Science and Engineering, Pusan National University, 2 Busandaehak-ro 63beon-gil, Geumjeong-gu, Busan 46241, Korea
| | - Jung Woo Lee
- Department of Materials Science and Engineering, Pusan National University, 2 Busandaehak-ro 63beon-gil, Geumjeong-gu, Busan 46241, Korea
| | - Min-Ho Seo
- Department of Information Convergence Engineering, Pusan National University, 49 Busandaehak-ro, Mulgeum-eup, Yangsan-si 50612, Gyeongsangnam-do, Korea
- School of Biomedical Convergence Engineering, Pusan National University, 49 Busandaehak-ro, Mulgeum-eup, Yangsan-si 50612, Gyeongsangnam-do, Korea
| |
Collapse
|
64
|
High-speed, scanned laser structuring of multi-layered eco/bioresorbable materials for advanced electronic systems. Nat Commun 2022; 13:6518. [PMID: 36316354 PMCID: PMC9622701 DOI: 10.1038/s41467-022-34173-0] [Citation(s) in RCA: 10] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/22/2022] [Accepted: 10/13/2022] [Indexed: 11/06/2022] Open
Abstract
Physically transient forms of electronics enable unique classes of technologies, ranging from biomedical implants that disappear through processes of bioresorption after serving a clinical need to internet-of-things devices that harmlessly dissolve into the environment following a relevant period of use. Here, we develop a sustainable manufacturing pathway, based on ultrafast pulsed laser ablation, that can support high-volume, cost-effective manipulation of a diverse collection of organic and inorganic materials, each designed to degrade by hydrolysis or enzymatic activity, into patterned, multi-layered architectures with high resolution and accurate overlay registration. The technology can operate in patterning, thinning and/or cutting modes with (ultra)thin eco/bioresorbable materials of different types of semiconductors, dielectrics, and conductors on flexible substrates. Component-level demonstrations span passive and active devices, including diodes and field-effect transistors. Patterning these devices into interconnected layouts yields functional systems, as illustrated in examples that range from wireless implants as monitors of neural and cardiac activity, to thermal probes of microvascular flow, and multi-electrode arrays for biopotential sensing. These advances create important processing options for eco/bioresorbable materials and associated electronic systems, with immediate applicability across nearly all types of bioelectronic studies.
Collapse
|
65
|
Sang M, Kim K, Shin J, Yu KJ. Ultra-Thin Flexible Encapsulating Materials for Soft Bio-Integrated Electronics. ADVANCED SCIENCE (WEINHEIM, BADEN-WURTTEMBERG, GERMANY) 2022; 9:e2202980. [PMID: 36031395 PMCID: PMC9596833 DOI: 10.1002/advs.202202980] [Citation(s) in RCA: 16] [Impact Index Per Article: 8.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/22/2022] [Revised: 07/22/2022] [Indexed: 05/11/2023]
Abstract
Recently, bioelectronic devices extensively researched and developed through the convergence of flexible biocompatible materials and electronics design that enables more precise diagnostics and therapeutics in human health care and opens up the potential to expand into various fields, such as clinical medicine and biomedical research. To establish an accurate and stable bidirectional bio-interface, protection against the external environment and high mechanical deformation is essential for wearable bioelectronic devices. In the case of implantable bioelectronics, special encapsulation materials and optimized mechanical designs and configurations that provide electronic stability and functionality are required for accommodating various organ properties, lifespans, and functions in the biofluid environment. Here, this study introduces recent developments of ultra-thin encapsulations with novel materials that can preserve or even improve the electrical performance of wearable and implantable bio-integrated electronics by supporting safety and stability for protection from destruction and contamination as well as optimizing the use of bioelectronic systems in physiological environments. In addition, a summary of the materials, methods, and characteristics of the most widely used encapsulation technologies is introduced, thereby providing a strategic selection of appropriate choices of recently developed flexible bioelectronics.
Collapse
Affiliation(s)
- Mingyu Sang
- School of Electrical and Electronic EngineeringYonsei University50 Yonsei‐ro, SeodaemunguSeoul03722Republic of Korea
| | - Kyubeen Kim
- School of Electrical and Electronic EngineeringYonsei University50 Yonsei‐ro, SeodaemunguSeoul03722Republic of Korea
| | - Jongwoon Shin
- School of Electrical and Electronic EngineeringYonsei University50 Yonsei‐ro, SeodaemunguSeoul03722Republic of Korea
| | - Ki Jun Yu
- School of Electrical and Electronic EngineeringYonsei University50 Yonsei‐ro, SeodaemunguSeoul03722Republic of Korea
- YU‐KIST InstituteYonsei University50 Yonsei‐ro, SeodaemunguSeoul03722Republic of Korea
| |
Collapse
|
66
|
Nan K, Feig VR, Ying B, Howarth JG, Kang Z, Yang Y, Traverso G. Mucosa-interfacing electronics. NATURE REVIEWS. MATERIALS 2022; 7:908-925. [PMID: 36124042 PMCID: PMC9472746 DOI: 10.1038/s41578-022-00477-2] [Citation(s) in RCA: 19] [Impact Index Per Article: 9.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Accepted: 07/28/2022] [Indexed: 06/15/2023]
Abstract
The surface mucosa that lines many of our organs houses myriad biometric signals and, therefore, has great potential as a sensor-tissue interface for high-fidelity and long-term biosensing. However, progress is still nascent for mucosa-interfacing electronics owing to challenges with establishing robust sensor-tissue interfaces; device localization, retention and removal; and power and data transfer. This is in sharp contrast to the rapidly advancing field of skin-interfacing electronics, which are replacing traditional hospital visits with minimally invasive, real-time, continuous and untethered biosensing. This Review aims to bridge the gap between skin-interfacing electronics and mucosa-interfacing electronics systems through a comparison of the properties and functions of the skin and internal mucosal surfaces. The major physiological signals accessible through mucosa-lined organs are surveyed and design considerations for the next generation of mucosa-interfacing electronics are outlined based on state-of-the-art developments in bio-integrated electronics. With this Review, we aim to inspire hardware solutions that can serve as a foundation for developing personalized biosensing from the mucosa, a relatively uncharted field with great scientific and clinical potential.
Collapse
Affiliation(s)
- Kewang Nan
- Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA USA
- Division of Gastroenterology, Hepatology and Endoscopy, Brigham and Women’s Hospital, Harvard Medical School, Boston, MA USA
| | - Vivian R. Feig
- Division of Gastroenterology, Hepatology and Endoscopy, Brigham and Women’s Hospital, Harvard Medical School, Boston, MA USA
- Koch Institute for Integrative Cancer Research, Massachusetts Institute of Technology, Cambridge, MA USA
| | - Binbin Ying
- Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA USA
- Division of Gastroenterology, Hepatology and Endoscopy, Brigham and Women’s Hospital, Harvard Medical School, Boston, MA USA
| | - Julia G. Howarth
- Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA USA
| | - Ziliang Kang
- Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA USA
- Division of Gastroenterology, Hepatology and Endoscopy, Brigham and Women’s Hospital, Harvard Medical School, Boston, MA USA
| | - Yiyuan Yang
- Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA USA
| | - Giovanni Traverso
- Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA USA
- Division of Gastroenterology, Hepatology and Endoscopy, Brigham and Women’s Hospital, Harvard Medical School, Boston, MA USA
| |
Collapse
|
67
|
Lyu H, Li J, Yuan Z, Liu H, Sun Z, Jiang R, Yu X, Hu Y, Pei Y, Ding J, Shen Y, Guo C. Supertough and Highly Stretchable Silk Protein-based Films with Controlled Biodegradability. Acta Biomater 2022; 153:149-158. [PMID: 36100175 DOI: 10.1016/j.actbio.2022.09.010] [Citation(s) in RCA: 4] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/06/2022] [Revised: 09/06/2022] [Accepted: 09/06/2022] [Indexed: 11/01/2022]
Abstract
Naturally derived protein-based biopolymers are considered potential biomaterials in biomedical applications and eco-friendly materials for replacing current petroleum-based polymers due to their good biocompatibility, low environmental impact, and tunable degradability. However, current strategies for fabricating protein-based materials with superior properties and tailored functionality in a scalable manner are still lacking. Here, we demonstrate an aqueous-based scalable approach for fabricating silk protein-based films through controlled molecular self-assembly (CMS) of silk proteins with plasticizers and salt ions. The films fabricated using this method can achieve a toughness of up to 64±5 MJ/m3 with a stretchability of up to 574±31%. We also demonstrate the tunable enzymatic degradability, low in vitro cytotoxicity, and good in vivo biocompatibility of the films. Furthermore, the films can be patterned with predesigned complex structures through laser cutting and functionalized with bioactive components. The functional silk protein-based films show great potential in various applications, including flexible electronics, bioelectronics, tissue engineering, and bioplastic packaging. STATEMENT OF SIGNIFICANCE: Inspired by the naturally optimized multi-scale self-assembly of silk proteins in natural silks, we develop an aqueous-based approach for scalable production of superior protein-based films through controlled molecular self-assembly (CMS) of silk proteins with glycerol and calcium ions. The prepared silk films present outstanding mechanical properties, controlled enzymatic biodegradability, low in vitro cytotoxicity, and good in vivo biocompatibility. Notably, the films fabricated using this method can achieve a high toughness of 64±5 MJ/m3 with a stretchability of 594±31%. The approach introduced in this work provides a facile route toward making silk-based materials with superior properties. It also paves new avenues for developing functional protein-based materials with precisely controlled structures and properties for various applications.
Collapse
Affiliation(s)
- Hao Lyu
- School of Engineering, Westlake University, Hangzhou, Zhejiang, China, 310023
| | - Jinghang Li
- School of Engineering, Westlake University, Hangzhou, Zhejiang, China, 310023
| | - Zhechen Yuan
- School of Medicine, Ningbo University, Ningbo, Zhejiang, China, 315211; Department of Otorhinolaryngology Head and Neck Surgery, Ningbo Medical Center of Lihuili Hospital, The Affiliated Hospital of Ningbo University, Ningbo, Zhejiang, China, 315040
| | - Haoran Liu
- School of Engineering, Westlake University, Hangzhou, Zhejiang, China, 310023
| | - Ziyang Sun
- School of Engineering, Westlake University, Hangzhou, Zhejiang, China, 310023
| | - Rui Jiang
- School of Engineering, Westlake University, Hangzhou, Zhejiang, China, 310023
| | - Xin Yu
- School of Engineering, Westlake University, Hangzhou, Zhejiang, China, 310023
| | - Yi Hu
- School of Medicine, Ningbo University, Ningbo, Zhejiang, China, 315211; Department of Otorhinolaryngology Head and Neck Surgery, Ningbo Medical Center of Lihuili Hospital, The Affiliated Hospital of Ningbo University, Ningbo, Zhejiang, China, 315040
| | - Ying Pei
- School of Materials Science and Engineering, Zhengzhou University, Zhengzhou, Henan, China, 450001
| | - Jie Ding
- Instrumentation and Service Center for Molecular Sciences, Westlake University, Hangzhou, Zhejiang, China, 310024
| | - Yi Shen
- School of Medicine, Ningbo University, Ningbo, Zhejiang, China, 315211; Department of Otorhinolaryngology Head and Neck Surgery, Ningbo Medical Center of Lihuili Hospital, The Affiliated Hospital of Ningbo University, Ningbo, Zhejiang, China, 315040.
| | - Chengchen Guo
- School of Engineering, Westlake University, Hangzhou, Zhejiang, China, 310023.
| |
Collapse
|
68
|
Zhai Z, Du X, Long Y, Zheng H. Biodegradable polymeric materials for flexible and degradable electronics. FRONTIERS IN ELECTRONICS 2022. [DOI: 10.3389/felec.2022.985681] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/13/2022] Open
Abstract
Biodegradable electronics have great potential to reduce the environmental footprint of electronic devices and to avoid secondary removal of implantable health monitors and therapeutic electronics. Benefiting from the intensive innovation on biodegradable nanomaterials, current transient electronics can realize full components’ degradability. However, design of materials with tissue-comparable flexibility, desired dielectric properties, suitable biocompatibility and programmable biodegradability will always be a challenge to explore the subtle trade-offs between these parameters. In this review, we firstly discuss the general chemical structure and degradation behavior of polymeric biodegradable materials that have been widely studied for various applications. Then, specific properties of different degradable polymer materials such as biocompatibility, biodegradability, and flexibility were compared and evaluated for real-life applications. Complex biodegradable electronics and related strategies with enhanced functionality aimed for different components including substrates, insulators, conductors and semiconductors in complex biodegradable electronics are further researched and discussed. Finally, typical applications of biodegradable electronics in sensing, therapeutic drug delivery, energy storage and integrated electronic systems are highlighted. This paper critically reviews the significant progress made in the field and highlights the future prospects.
Collapse
|
69
|
Huang Y, Cui Y, Deng H, Wang J, Hong R, Hu S, Hou H, Dong Y, Wang H, Chen J, Li L, Xie Y, Sun P, Fu X, Yin L, Xiong W, Shi SH, Luo M, Wang S, Li X, Sheng X. Bioresorbable thin-film silicon diodes for the optoelectronic excitation and inhibition of neural activities. Nat Biomed Eng 2022; 7:486-498. [PMID: 36065014 DOI: 10.1038/s41551-022-00931-0] [Citation(s) in RCA: 16] [Impact Index Per Article: 8.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/02/2021] [Accepted: 07/25/2022] [Indexed: 11/09/2022]
Abstract
Neural activities can be modulated by leveraging light-responsive nanomaterials as interfaces for exerting photothermal, photoelectrochemical or photocapacitive effects on neurons or neural tissues. Here we show that bioresorbable thin-film monocrystalline silicon pn diodes can be used to optoelectronically excite or inhibit neural activities by establishing polarity-dependent positive or negative photovoltages at the semiconductor/solution interface. Under laser illumination, the silicon-diode optoelectronic interfaces allowed for the deterministic depolarization or hyperpolarization of cultured neurons as well as the upregulated or downregulated intracellular calcium dynamics. The optoelectronic interfaces can also be mounted on nerve tissue to activate or silence neural activities in peripheral and central nervous tissues, as we show in mice with exposed sciatic nerves and somatosensory cortices. Bioresorbable silicon-based optoelectronic thin films that selectively excite or inhibit neural tissue may find advantageous biomedical applicability.
Collapse
Affiliation(s)
- Yunxiang Huang
- Department of Electronic Engineering, Beijing National Research Center for Information Science and Technology, Institute for Precision Medicine, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China.,School of Materials Science and Engineering, The Key Laboratory of Advanced Materials of Ministry of Education, State Key Laboratory of New Ceramics and Fine Processing, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China.,IDG/McGovern Institute for Brain Research, Tsinghua University, Beijing, China
| | - Yuting Cui
- Chinese Institute for Brain Research, Beijing, China.,National Institute of Biological Sciences, Beijing, China
| | - Hanjie Deng
- CAS Key Laboratory of Brain Connectome and Manipulation, the Brain Cognition and Brain Disease Institute (BCBDI), Shenzhen Institute of Advanced Technology, Shenzhen-Hong Kong Institute of Brain Science-Shenzhen Fundamental Research Institutions, Shenzhen, China
| | - Jingjing Wang
- CAS Key Laboratory of Brain Connectome and Manipulation, the Brain Cognition and Brain Disease Institute (BCBDI), Shenzhen Institute of Advanced Technology, Shenzhen-Hong Kong Institute of Brain Science-Shenzhen Fundamental Research Institutions, Shenzhen, China
| | - Rongqi Hong
- CAS Key Laboratory of Brain Connectome and Manipulation, the Brain Cognition and Brain Disease Institute (BCBDI), Shenzhen Institute of Advanced Technology, Shenzhen-Hong Kong Institute of Brain Science-Shenzhen Fundamental Research Institutions, Shenzhen, China
| | - Shuhan Hu
- IDG/McGovern Institute for Brain Research, Tsinghua University, Beijing, China.,School of Life Sciences, Tsinghua University, Beijing, China
| | - Hanqing Hou
- IDG/McGovern Institute for Brain Research, Tsinghua University, Beijing, China.,School of Life Sciences, Tsinghua University, Beijing, China
| | - Yuanrui Dong
- Beijing Advanced Innovation Center for Intelligent Robots and Systems, Beijing Institute of Technology, Beijing, China
| | - Huachun Wang
- Department of Electronic Engineering, Beijing National Research Center for Information Science and Technology, Institute for Precision Medicine, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China
| | - Junyu Chen
- Department of Electronic Engineering, Beijing National Research Center for Information Science and Technology, Institute for Precision Medicine, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China
| | - Lizhu Li
- Department of Electronic Engineering, Beijing National Research Center for Information Science and Technology, Institute for Precision Medicine, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China
| | - Yang Xie
- Department of Electronic Engineering, Beijing National Research Center for Information Science and Technology, Institute for Precision Medicine, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China
| | - Pengcheng Sun
- School of Materials Science and Engineering, The Key Laboratory of Advanced Materials of Ministry of Education, State Key Laboratory of New Ceramics and Fine Processing, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China
| | - Xin Fu
- School of Materials Science and Engineering, The Key Laboratory of Advanced Materials of Ministry of Education, State Key Laboratory of New Ceramics and Fine Processing, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China
| | - Lan Yin
- School of Materials Science and Engineering, The Key Laboratory of Advanced Materials of Ministry of Education, State Key Laboratory of New Ceramics and Fine Processing, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China
| | - Wei Xiong
- IDG/McGovern Institute for Brain Research, Tsinghua University, Beijing, China.,School of Life Sciences, Tsinghua University, Beijing, China
| | - Song-Hai Shi
- IDG/McGovern Institute for Brain Research, Tsinghua University, Beijing, China.,School of Life Sciences, Tsinghua University, Beijing, China
| | - Minmin Luo
- IDG/McGovern Institute for Brain Research, Tsinghua University, Beijing, China.,Chinese Institute for Brain Research, Beijing, China.,National Institute of Biological Sciences, Beijing, China.,School of Life Sciences, Tsinghua University, Beijing, China
| | - Shirong Wang
- Beijing Advanced Innovation Center for Intelligent Robots and Systems, Beijing Institute of Technology, Beijing, China.
| | - Xiaojian Li
- CAS Key Laboratory of Brain Connectome and Manipulation, the Brain Cognition and Brain Disease Institute (BCBDI), Shenzhen Institute of Advanced Technology, Shenzhen-Hong Kong Institute of Brain Science-Shenzhen Fundamental Research Institutions, Shenzhen, China.
| | - Xing Sheng
- Department of Electronic Engineering, Beijing National Research Center for Information Science and Technology, Institute for Precision Medicine, Center for Flexible Electronics Technology, Tsinghua University, Beijing, China. .,IDG/McGovern Institute for Brain Research, Tsinghua University, Beijing, China.
| |
Collapse
|
70
|
Yoo C, Yoon J, Kaium MG, Osorto B, Han SS, Kim JH, Kim BK, Chung HS, Kim DJ, Jung Y. Large-area vertically aligned 2D MoS 2layers on TEMPO-cellulose nanofibers for biodegradable transient gas sensors. NANOTECHNOLOGY 2022; 33:475502. [PMID: 35944420 DOI: 10.1088/1361-6528/ac8811] [Citation(s) in RCA: 4] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/08/2022] [Accepted: 08/09/2022] [Indexed: 06/15/2023]
Abstract
Crystallographically anisotropic two-dimensional (2D) molybdenum disulfide (MoS2) with vertically aligned (VA) layers is attractive for electrochemical sensing owing to its surface-enriched dangling bonds coupled with extremely large mechanical deformability. In this study, we explored VA-2D MoS2layers integrated on cellulose nanofibers (CNFs) for detecting various volatile organic compound gases. Sensor devices employing VA-2D MoS2/CNFs exhibited excellent sensitivities for the tested gases of ethanol, methanol, ammonia, and acetone; e.g. a high response rate up to 83.39% for 100 ppm ethanol, significantly outperforming previously reported sensors employing horizontally aligned 2D MoS2layers. Furthermore, VA-2D MoS2/CNFs were identified to be completely dissolvable in buffer solutions such as phosphate-buffered saline solution and baking soda buffer solution without releasing toxic chemicals. This unusual combination of high sensitivity and excellent biodegradability inherent to VA-2D MoS2/CNFs offers unprecedented opportunities for exploring mechanically reconfigurable sensor technologies with bio-compatible transient characteristics.
Collapse
Affiliation(s)
- Changhyeon Yoo
- NanoScience Technology Center, University of Central Florida, Orlando, FL 32826, United States of America
| | - Jaesik Yoon
- Materials Research and Education Center, 275 Wilmore Laboratory, Auburn University, Auburn, AL 36849, United States of America
| | - Md Golam Kaium
- NanoScience Technology Center, University of Central Florida, Orlando, FL 32826, United States of America
- Department of Materials Science and Engineering, University of Central Florida, Orlando, FL 32816, United States of America
| | - Brandon Osorto
- NanoScience Technology Center, University of Central Florida, Orlando, FL 32826, United States of America
| | - Sang Sub Han
- NanoScience Technology Center, University of Central Florida, Orlando, FL 32826, United States of America
| | - Jung Han Kim
- Department of Materials Science and Engineering, Dong-A University, Busan 49315, Republic of Korea
| | - Bo Kyoung Kim
- Analytical Research Division, Korea Basic Science Institute, Jeonju 54907, Republic of Korea
| | - Hee-Suk Chung
- Analytical Research Division, Korea Basic Science Institute, Jeonju 54907, Republic of Korea
| | - Dong-Joo Kim
- Materials Research and Education Center, 275 Wilmore Laboratory, Auburn University, Auburn, AL 36849, United States of America
| | - Yeonwoong Jung
- NanoScience Technology Center, University of Central Florida, Orlando, FL 32826, United States of America
- Department of Materials Science and Engineering, University of Central Florida, Orlando, FL 32816, United States of America
- Department of Electrical and Computer Engineering, University of Central Florida, Orlando, FL 32816, United States of America
| |
Collapse
|
71
|
Corsi M, Paghi A, Mariani S, Golinelli G, Debrassi A, Egri G, Leo G, Vandini E, Vilella A, Dähne L, Giuliani D, Barillaro G. Bioresorbable Nanostructured Chemical Sensor for Monitoring of pH Level In Vivo. ADVANCED SCIENCE (WEINHEIM, BADEN-WURTTEMBERG, GERMANY) 2022; 9:e2202062. [PMID: 35618637 PMCID: PMC9353472 DOI: 10.1002/advs.202202062] [Citation(s) in RCA: 13] [Impact Index Per Article: 6.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 04/13/2022] [Indexed: 06/15/2023]
Abstract
Here, the authors report on the manufacturing and in vivo assessment of a bioresorbable nanostructured pH sensor. The sensor consists of a micrometer-thick porous silica membrane conformably coated layer-by-layer with a nanometer-thick multilayer stack of two polyelectrolytes labeled with a pH-insensitive fluorophore. The sensor fluorescence changes linearly with the pH value in the range 4 to 7.5 upon swelling/shrinking of the polymer multilayer and enables performing real-time measurements of the pH level with high stability, reproducibility, and accuracy, over 100 h of continuous operation. In vivo studies carried out implanting the sensor in the subcutis on the back of mice confirm real-time monitoring of the local pH level through skin. Full degradation of the pH sensor occurs in one week from implant in the animal model, and its biocompatibility after 2 months is confirmed by histological and fluorescence analyses. The proposed approach can be extended to the detection of other (bio)markers in vivo by engineering the functionality of one (at least) of the polyelectrolytes with suitable receptors, thus paving the way to implantable bioresorbable chemical sensors.
Collapse
Affiliation(s)
- Martina Corsi
- Dipartimento di Ingegneria dell'InformazioneUniversità di Pisavia G. Caruso 16Pisa56122Italy
| | - Alessandro Paghi
- Dipartimento di Ingegneria dell'InformazioneUniversità di Pisavia G. Caruso 16Pisa56122Italy
| | - Stefano Mariani
- Dipartimento di Ingegneria dell'InformazioneUniversità di Pisavia G. Caruso 16Pisa56122Italy
| | - Giulia Golinelli
- Department of Medical and Surgical Sciences for Children & AdultsUniversity‐Hospital of Modena and Reggio EmiliaVia del Pozzo 71Modena41124Italy
| | - Aline Debrassi
- Surflay Nanotec GmbHMax‐Planck‐Straße 312489BerlinGermany
| | - Gabriella Egri
- Surflay Nanotec GmbHMax‐Planck‐Straße 312489BerlinGermany
| | - Giuseppina Leo
- Department of Biomedical Metabolic and Neural SciencesUniversity of Modena and Reggio Emiliavia G. Campi 287Modena41125Italy
| | - Eleonora Vandini
- Department of Biomedical Metabolic and Neural SciencesUniversity of Modena and Reggio Emiliavia G. Campi 287Modena41125Italy
| | - Antonietta Vilella
- Department of Biomedical Metabolic and Neural SciencesUniversity of Modena and Reggio Emiliavia G. Campi 287Modena41125Italy
| | - Lars Dähne
- Surflay Nanotec GmbHMax‐Planck‐Straße 312489BerlinGermany
| | - Daniela Giuliani
- Department of Biomedical Metabolic and Neural SciencesUniversity of Modena and Reggio Emiliavia G. Campi 287Modena41125Italy
| | - Giuseppe Barillaro
- Dipartimento di Ingegneria dell'InformazioneUniversità di Pisavia G. Caruso 16Pisa56122Italy
| |
Collapse
|
72
|
Sethi SS, Kovac M, Wiesemüller F, Miriyev A, Boutry CM. Biodegradable sensors are ready to transform autonomous ecological monitoring. Nat Ecol Evol 2022; 6:1245-1247. [PMID: 35835828 DOI: 10.1038/s41559-022-01824-w] [Citation(s) in RCA: 7] [Impact Index Per Article: 3.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/09/2022]
Affiliation(s)
- Sarab S Sethi
- Department of Plant Sciences, University of Cambridge, Cambridge, UK. .,Centre for Biodiversity and Environment Research, UCL, London, UK.
| | - Mirko Kovac
- Materials and Technology Center of Robotics, Empa - Swiss Federal Laboratories for Materials Science and Technology, Dübendorf, Switzerland.,Aerial Robotics Laboratory, Imperial College London, London, UK
| | - Fabian Wiesemüller
- Materials and Technology Center of Robotics, Empa - Swiss Federal Laboratories for Materials Science and Technology, Dübendorf, Switzerland.,Aerial Robotics Laboratory, Imperial College London, London, UK
| | - Aslan Miriyev
- Physical AI (PAI) Laboratory, Department of Mechanical Engineering, Ben-Gurion University of the Negev, Be'er Sheva, Israel
| | | |
Collapse
|
73
|
Kwon J, DelRe C, Kang P, Hall A, Arnold D, Jayapurna I, Ma L, Michalek M, Ritchie RO, Xu T. Conductive Ink with Circular Life Cycle for Printed Electronics. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2202177. [PMID: 35580071 DOI: 10.1002/adma.202202177] [Citation(s) in RCA: 10] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 03/08/2022] [Revised: 05/11/2022] [Indexed: 06/15/2023]
Abstract
Electronic waste carries energetic costs and an environmental burden rivaling that of plastic waste due to the rarity and toxicity of the heavy-metal components. Recyclable conductive composites are introduced for printed circuits formulated with polycaprolactone (PCL), conductive fillers, and enzyme/protectant nanoclusters. Circuits can be printed with flexibility (breaking strain ≈80%) and conductivity (≈2.1 × 104 S m-1 ). These composites are degraded at the end of life by immersion in warm water with programmable latency. Approximately 94% of the functional fillers can be recycled and reused with similar device performance. The printed circuits remain functional and degradable after shelf storage for at least 7 months at room temperature and one month of continuous operation under electrical voltage. The present studies provide composite design toward recyclable and easily disposable printed electronics for applications such as wearable electronics, biosensors, and soft robotics.
Collapse
Affiliation(s)
- Junpyo Kwon
- Department of Mechanical Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
- Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, CA, 94720, USA
| | - Christopher DelRe
- Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, CA, 94720, USA
- Department of Materials Science and Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
| | - Philjun Kang
- Department of Chemistry, University of California, Berkeley, Berkeley, CA, 94720, USA
| | - Aaron Hall
- Department of Materials Science and Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
| | - Daniel Arnold
- Department of Chemical Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
| | - Ivan Jayapurna
- Department of Materials Science and Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
| | - Le Ma
- Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, CA, 94720, USA
- Department of Materials Science and Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
| | - Matthew Michalek
- Department of Materials Science and Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
| | - Robert O Ritchie
- Department of Mechanical Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
- Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, CA, 94720, USA
- Department of Materials Science and Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
| | - Ting Xu
- Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, CA, 94720, USA
- Department of Materials Science and Engineering, University of California, Berkeley, Berkeley, CA, 94720, USA
- Department of Chemistry, University of California, Berkeley, Berkeley, CA, 94720, USA
| |
Collapse
|
74
|
Reeder JT, Xie Z, Yang Q, Seo MH, Yan Y, Deng Y, Jinkins KR, Krishnan SR, Liu C, McKay S, Patnaude E, Johnson A, Zhao Z, Kim MJ, Xu Y, Huang I, Avila R, Felicelli C, Ray E, Guo X, Ray WZ, Huang Y, MacEwan MR, Rogers JA. Soft, bioresorbable coolers for reversible conduction block of peripheral nerves. Science 2022; 377:109-115. [PMID: 35771907 DOI: 10.1126/science.abl8532] [Citation(s) in RCA: 46] [Impact Index Per Article: 23.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/19/2022]
Abstract
Implantable devices capable of targeted and reversible blocking of peripheral nerve activity may provide alternatives to opioids for treating pain. Local cooling represents an attractive means for on-demand elimination of pain signals, but traditional technologies are limited by rigid, bulky form factors; imprecise cooling; and requirements for extraction surgeries. Here, we introduce soft, bioresorbable, microfluidic devices that enable delivery of focused, minimally invasive cooling power at arbitrary depths in living tissues with real-time temperature feedback control. Construction with water-soluble, biocompatible materials leads to dissolution and bioresorption as a mechanism to eliminate unnecessary device load and risk to the patient without additional surgeries. Multiweek in vivo trials demonstrate the ability to rapidly and precisely cool peripheral nerves to provide local, on-demand analgesia in rat models for neuropathic pain.
Collapse
Affiliation(s)
- Jonathan T Reeder
- Knight Campus for Accelerating Scientific Impact, University of Oregon, Eugene, OR, USA.,Department of Materials Science and Engineering, Northwestern University, Evanston, IL, USA.,Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL, USA
| | - Zhaoqian Xie
- State Key Laboratory of Structural Analysis for Industrial Equipment, Department of Engineering Mechanics, Dalian University of Technology, Dalian, China.,Ningbo Institute of Dalian University of Technology, Ningbo, China
| | - Quansan Yang
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL, USA.,Department of Mechanical Engineering, Northwestern University, Evanston, IL, USA
| | - Min-Ho Seo
- Department of Materials Science and Engineering, Northwestern University, Evanston, IL, USA.,Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL, USA.,School of Biomedical Convergence Engineering, College of Information and Biomedical Engineering, Pusan National University, Busan, Republic of Korea
| | - Ying Yan
- Department of Neurological Surgery, Washington University School of Medicine, St. Louis, MO, USA
| | - Yujun Deng
- State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, Shanghai, China
| | - Katherine R Jinkins
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL, USA
| | - Siddharth R Krishnan
- Department of Materials Science and Engineering, Northwestern University, Evanston, IL, USA.,Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL, USA
| | - Claire Liu
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL, USA.,Department of Biomedical Engineering, Northwestern University, Evanston, IL, USA
| | - Shannon McKay
- Department of Biomedical Engineering, Northwestern University, Evanston, IL, USA
| | - Emily Patnaude
- Department of Biomedical Engineering, Northwestern University, Evanston, IL, USA
| | - Alexandra Johnson
- Department of Biomedical Engineering, Northwestern University, Evanston, IL, USA
| | - Zichen Zhao
- State Key Laboratory of Structural Analysis for Industrial Equipment, Department of Engineering Mechanics, Dalian University of Technology, Dalian, China.,Ningbo Institute of Dalian University of Technology, Ningbo, China
| | - Moon Joo Kim
- Department of Chemical Engineering, Northwestern University, Evanston, IL, USA
| | - Yameng Xu
- The Institute of Materials Science and Engineering, Washington University, St. Louis, MO, USA
| | - Ivy Huang
- Department of Materials Science and Engineering, Northwestern University, Evanston, IL, USA.,Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL, USA
| | - Raudel Avila
- Department of Mechanical Engineering, Northwestern University, Evanston, IL, USA
| | | | - Emily Ray
- Department of Biomedical Engineering, Washington University, St. Louis, MO, USA
| | - Xu Guo
- State Key Laboratory of Structural Analysis for Industrial Equipment, Department of Engineering Mechanics, Dalian University of Technology, Dalian, China.,Ningbo Institute of Dalian University of Technology, Ningbo, China
| | - Wilson Z Ray
- Department of Neurological Surgery, Washington University School of Medicine, St. Louis, MO, USA.,Department of Biomedical Engineering, Washington University, St. Louis, MO, USA
| | - Yonggang Huang
- Department of Materials Science and Engineering, Northwestern University, Evanston, IL, USA.,Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL, USA.,Department of Mechanical Engineering, Northwestern University, Evanston, IL, USA.,Departments of Civil and Environmental Engineering, Northwestern University, Evanston, IL, USA
| | - Matthew R MacEwan
- Department of Neurological Surgery, Washington University School of Medicine, St. Louis, MO, USA.,Department of Biomedical Engineering, Washington University, St. Louis, MO, USA
| | - John A Rogers
- Department of Materials Science and Engineering, Northwestern University, Evanston, IL, USA.,Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL, USA.,Department of Mechanical Engineering, Northwestern University, Evanston, IL, USA.,Department of Biomedical Engineering, Northwestern University, Evanston, IL, USA.,Department of Chemistry, Northwestern University, Evanston, IL, USA.,Department of Electrical Engineering and Computer Science, Northwestern University, Evanston, IL, USA.,Department of Neurological Surgery, Feinberg School of Medicine, Northwestern University, Evanston, IL, USA
| |
Collapse
|
75
|
Bonné R, Wouters K, Lustermans JJM, Manca JV. Biomaterials and Electroactive Bacteria for Biodegradable Electronics. Front Microbiol 2022; 13:906363. [PMID: 35794922 PMCID: PMC9252516 DOI: 10.3389/fmicb.2022.906363] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/28/2022] [Accepted: 05/20/2022] [Indexed: 11/19/2022] Open
Abstract
The global production of unrecycled electronic waste is extensively growing each year, urging the search for alternatives in biodegradable electronic materials. Electroactive bacteria and their nanowires have emerged as a new route toward electronic biological materials (e-biologics). Recent studies on electron transport in cable bacteria—filamentous, multicellular electroactive bacteria—showed centimeter long electron transport in an organized conductive fiber structure with high conductivities and remarkable intrinsic electrical properties. In this work we give a brief overview of the recent advances in biodegradable electronics with a focus on the use of biomaterials and electroactive bacteria, and with special attention for cable bacteria. We investigate the potential of cable bacteria in this field, as we compare the intrinsic electrical properties of cable bacteria to organic and inorganic electronic materials. Based on their intrinsic electrical properties, we show cable bacteria filaments to have great potential as for instance interconnects and transistor channels in a new generation of bioelectronics. Together with other biomaterials and electroactive bacteria they open electrifying routes toward a new generation of biodegradable electronics.
Collapse
Affiliation(s)
- Robin Bonné
- Center for Electromicrobiology, Department of Biology, Aarhus University, Aarhus, Denmark
- *Correspondence: Robin Bonné,
| | | | - Jamie J. M. Lustermans
- Center for Electromicrobiology, Department of Biology, Aarhus University, Aarhus, Denmark
| | | |
Collapse
|
76
|
Yamada S. A Transient Supercapacitor with a Water-Dissolvable Ionic Gel for Sustainable Electronics. ACS APPLIED MATERIALS & INTERFACES 2022; 14:26595-26603. [PMID: 35653282 DOI: 10.1021/acsami.2c00915] [Citation(s) in RCA: 6] [Impact Index Per Article: 3.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/15/2023]
Abstract
We develop an environmentally benign supercapacitor, which decomposes by contact with water, incorporating an ionic liquid, carbon powder, a cellulose separator, and a molybdenum electrode. The ionic liquid is dispersed into a water-dissolvable polymer, poly(vinyl alcohol), to produce a solid electrolyte, so-called ionic gel. A carbon composite mixed with the ionic liquid maintains a gel form. The ionic gel and the carbon composite enable an all-solid-state supercapacitor, which can be charged at a voltage of 1.5 V. The supercapacitor shows areal and volumetric capacitances of 65 mF/cm2 and 2.2 F/cm3, respectively. A cycle test reveals that capacitance retention and Coulombic efficiency are 77 and 90%, respectively. As for the dissolution test, the ionic gel and carbon composite dissolves in phosphate buffer solution in 18 days, and the Mo electrode is able to fully dissolve in 500-588 days. Potential applications of the environmentally benign supercapacitor include smart agriculture by monitoring of soil and disaster prevention by a wireless sensor network without the need for retrieval of devices after use.
Collapse
Affiliation(s)
- Shunsuke Yamada
- Department of Robotics, Tohoku University, Room 113, Building No. A15, Area A01, 6-6-01 Aoba, Aramakiaza, Aobaku, Sendaishi, Miyagi 980-8579, Japan
| |
Collapse
|
77
|
Gao D, Lv J, Lee PS. Natural Polymer in Soft Electronics: Opportunities, Challenges, and Future Prospects. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2105020. [PMID: 34757632 DOI: 10.1002/adma.202105020] [Citation(s) in RCA: 5] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/30/2021] [Revised: 08/20/2021] [Indexed: 05/21/2023]
Abstract
Pollution caused by nondegradable plastics has been a serious threat to environmental sustainability. Natural polymers, which can degrade in nature, provide opportunities to replace petroleum-based polymers, meanwhile driving technological advances and sustainable practices. In the research field of soft electronics, regenerated natural polymers are promising building blocks for passive dielectric substrates, active dielectric layers, and matrices in soft conductors. Here, the natural-polymer polymorphs and their compatibilization with a variety of inorganic/organic conductors through interfacial bonding/intermixing and surface functionalization for applications in various device modalities are delineated. Challenges that impede the broad utilization of natural polymers in soft electronics, including limited durability, compromises between conductivity and deformability, and limited exploration in controllable degradation, etc. are explicitly inspected, while the potential solutions along with future prospects are also proposed. Finally, integrative considerations on material properties, device functionalities, and environmental impact are addressed to warrant natural polymers as credible alternatives to synthetic ones, and provide viable options for sustainable soft electronics.
Collapse
Affiliation(s)
- Dace Gao
- School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore, 639798, Singapore
| | - Jian Lv
- School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore, 639798, Singapore
| | - Pooi See Lee
- School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore, 639798, Singapore
| |
Collapse
|
78
|
Research on Insurance Method for Energetic Materials on Information Self-Destruction Chips. MICROMACHINES 2022; 13:mi13060875. [PMID: 35744489 PMCID: PMC9227541 DOI: 10.3390/mi13060875] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 04/14/2022] [Revised: 05/22/2022] [Accepted: 05/30/2022] [Indexed: 12/04/2022]
Abstract
Detonation waves released by energetic materials provide an important means of physical self-destruction (Psd) for information storage chips (ISCs) in the information insurance field and offer advantages that include a rapid response and low driving energy. The high electrical sensitivity of energetic materials means that they are easily triggered by leakage currents and electrostatic forces. Therefore, a Psd module based on a graphene-based insurance actuator heterogeneously integrated with energetic materials is proposed. First, the force–balance relation between the electrostatic van der Waals force and the elastic recovery force of the insurance actuator’s graphene electrode is established to realize physical isolation and an electrical interconnection between the energetic materials and the peripheral electrical systems. Second, a numerical analysis of the detonation wave stress of the energetic materials in the air domain is performed, and the copper azide dosage required to achieve reliable ISC Psd is obtained. Third, the insurance actuator is prepared via graphene thin film processing and copper azide is prepared via an in situ reaction. The experimental results show that the energetic materials proposed can release physical isolation within 14 μs and can achieve ISC Psd under the application of a voltage signal (4.4–4.65 V). Copper azide (0.45–0.52 mg) can achieve physical damage over an ISC area (23.37–35.84 mm2) within an assembly gap (0.05–0.25 mm) between copper azide and ISC. The proposed method has high applicability for information insurance.
Collapse
|
79
|
Choi YS, Jeong H, Yin RT, Avila R, Pfenniger A, Yoo J, Lee JY, Tzavelis A, Lee YJ, Chen SW, Knight HS, Kim S, Ahn HY, Wickerson G, Vázquez-Guardado A, Higbee-Dempsey E, Russo BA, Napolitano MA, Holleran TJ, Razzak LA, Miniovich AN, Lee G, Geist B, Kim B, Han S, Brennan JA, Aras K, Kwak SS, Kim J, Waters EA, Yang X, Burrell A, Chun KS, Liu C, Wu C, Rwei AY, Spann AN, Banks A, Johnson D, Zhang ZJ, Haney CR, Jin SH, Sahakian AV, Huang Y, Trachiotis GD, Knight BP, Arora RK, Efimov IR, Rogers JA. A transient, closed-loop network of wireless, body-integrated devices for autonomous electrotherapy. Science 2022; 376:1006-1012. [PMID: 35617386 PMCID: PMC9282941 DOI: 10.1126/science.abm1703] [Citation(s) in RCA: 67] [Impact Index Per Article: 33.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/15/2022]
Abstract
Temporary postoperative cardiac pacing requires devices with percutaneous leads and external wired power and control systems. This hardware introduces risks for infection, limitations on patient mobility, and requirements for surgical extraction procedures. Bioresorbable pacemakers mitigate some of these disadvantages, but they demand pairing with external, wired systems and secondary mechanisms for control. We present a transient closed-loop system that combines a time-synchronized, wireless network of skin-integrated devices with an advanced bioresorbable pacemaker to control cardiac rhythms, track cardiopulmonary status, provide multihaptic feedback, and enable transient operation with minimal patient burden. The result provides a range of autonomous, rate-adaptive cardiac pacing capabilities, as demonstrated in rat, canine, and human heart studies. This work establishes an engineering framework for closed-loop temporary electrotherapy using wirelessly linked, body-integrated bioelectronic devices.
Collapse
Affiliation(s)
- Yeon Sik Choi
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Precision Biology Research Center, Sungkyunkwan University, Suwon, 16419, Republic of Korea
| | - Hyoyoung Jeong
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
| | - Rose T. Yin
- Department of Biomedical Engineering, The George Washington University, Washington, DC 20052, USA
| | - Raudel Avila
- Department of Mechanical Engineering, Northwestern University, Evanston, IL 60208, USA
| | - Anna Pfenniger
- Feinberg School of Medicine, Cardiology, Northwestern University, Chicago, IL 60611, USA
| | - Jaeyoung Yoo
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
| | - Jong Yoon Lee
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Sibel Health, Niles, IL, 60714, USA
| | - Andreas Tzavelis
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Department of Biomedical Engineering, Northwestern University, Evanston, IL 60208, USA
- Medical Scientist Training Program, Feinberg School of Medicine, Northwestern University, Chicago, IL 60611, USA
| | - Young Joong Lee
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
| | - Sheena W. Chen
- Department of General Surgery, The George Washington University, Washington, DC 20052, USA
- Department of Cardiothoracic Surgery, Veteran Affairs Medical Center, Washington, DC 20422, USA
| | - Helen S. Knight
- Department of Biomedical Engineering, The George Washington University, Washington, DC 20052, USA
| | - Seungyeob Kim
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Department of Electronic Engineering, Incheon National University, 119 Academy-ro, Yeonsu-gu, Incheon, 406-772, Republic of Korea
| | - Hak-Young Ahn
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Precision Biology Research Center, Sungkyunkwan University, Suwon, 16419, Republic of Korea
| | - Grace Wickerson
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Department of Materials Science and Engineering, Northwestern University, Evanston, IL 60208, USA
| | - Abraham Vázquez-Guardado
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
| | | | - Bender A. Russo
- Department of Biomedical Engineering, The George Washington University, Washington, DC 20052, USA
| | - Michael A. Napolitano
- Department of General Surgery, The George Washington University, Washington, DC 20052, USA
- Department of Cardiothoracic Surgery, Veteran Affairs Medical Center, Washington, DC 20422, USA
| | - Timothy J. Holleran
- Department of General Surgery, The George Washington University, Washington, DC 20052, USA
- Department of Cardiothoracic Surgery, Veteran Affairs Medical Center, Washington, DC 20422, USA
| | - Leen Abdul Razzak
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Department of Biomedical Engineering, Northwestern University, Evanston, IL 60208, USA
| | - Alana N. Miniovich
- Department of Biomedical Engineering, The George Washington University, Washington, DC 20052, USA
| | - Geumbee Lee
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
| | - Beth Geist
- Feinberg School of Medicine, Cardiology, Northwestern University, Chicago, IL 60611, USA
| | | | - Shuling Han
- Comprehensive Transplant Center, Feinberg School of Medicine, Northwestern University, Chicago, IL 60611, USA
- Department of Surgery, Feinberg School of Medicine, Northwestern University, Chicago, IL 60611, USA
| | - Jaclyn A. Brennan
- Department of Biomedical Engineering, The George Washington University, Washington, DC 20052, USA
| | - Kedar Aras
- Department of Biomedical Engineering, The George Washington University, Washington, DC 20052, USA
| | - Sung Soo Kwak
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Current Address: Center for Bionics of Biomedical Research Institute, Korea Institute of Science and Technology, Seoul 02792, Korea
| | - Joohee Kim
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
| | - Emily Alexandria Waters
- Department of Biomedical Engineering, Northwestern University, Evanston, IL 60208, USA
- Center for Advanced Molecular Imaging, Northwestern University, Evanston, IL 60208, USA
| | - Xiangxing Yang
- Department of Electrical and Computer Engineering, University of Texas at Austin, Austin, Tx, 78712, USA
| | - Amy Burrell
- Feinberg School of Medicine, Cardiology, Northwestern University, Chicago, IL 60611, USA
| | - Keum San Chun
- Department of Electrical and Computer Engineering, University of Texas at Austin, Austin, Tx, 78712, USA
| | - Claire Liu
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Department of Biomedical Engineering, The George Washington University, Washington, DC 20052, USA
| | - Changsheng Wu
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
| | - Alina Y. Rwei
- Department of Chemical Engineering, Delft University of Technology, Van der Maasweg 9, 2629 HZ Delft, The Netherlands
| | - Alisha N. Spann
- Center for Advanced Molecular Imaging, Northwestern University, Evanston, IL 60208, USA
| | - Anthony Banks
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
| | - David Johnson
- Feinberg School of Medicine, Cardiology, Northwestern University, Chicago, IL 60611, USA
| | - Zheng Jenny Zhang
- Comprehensive Transplant Center, Feinberg School of Medicine, Northwestern University, Chicago, IL 60611, USA
- Department of Surgery, Feinberg School of Medicine, Northwestern University, Chicago, IL 60611, USA
| | - Chad R. Haney
- Department of Biomedical Engineering, Northwestern University, Evanston, IL 60208, USA
- Center for Advanced Molecular Imaging, Northwestern University, Evanston, IL 60208, USA
| | - Sung Hun Jin
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Department of Electronic Engineering, Incheon National University, 119 Academy-ro, Yeonsu-gu, Incheon, 406-772, Republic of Korea
| | - Alan Varteres Sahakian
- Department of Biomedical Engineering, Northwestern University, Evanston, IL 60208, USA
- Department of Electrical and Computer Engineering, Northwestern University, Evanston, IL 60208, USA
| | - Yonggang Huang
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Department of Biomedical Engineering, The George Washington University, Washington, DC 20052, USA
- Department of Mechanical Engineering, Northwestern University, Evanston, IL 60208, USA
- Department of Civil and Environmental Engineering, Northwestern University, Evanston, IL 60208, USA
| | - Gregory D. Trachiotis
- Department of Cardiothoracic Surgery, Veteran Affairs Medical Center, Washington, DC 20422, USA
| | - Bradley P. Knight
- Feinberg School of Medicine, Cardiology, Northwestern University, Chicago, IL 60611, USA
| | - Rishi K. Arora
- Feinberg School of Medicine, Cardiology, Northwestern University, Chicago, IL 60611, USA
| | - Igor R. Efimov
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Department of Biomedical Engineering, The George Washington University, Washington, DC 20052, USA
| | - John A. Rogers
- Center for Bio-Integrated Electronics, Northwestern University, Evanston, IL 60208, USA
- Querrey Simpson Institute for Bioelectronics, Northwestern University, Evanston, IL 60208, USA
- Department of Biomedical Engineering, Northwestern University, Evanston, IL 60208, USA
- Department of Mechanical Engineering, Northwestern University, Evanston, IL 60208, USA
- Department of Materials Science and Engineering, Northwestern University, Evanston, IL 60208, USA
- Department of Neurological Surgery, Feinberg School of Medicine, Northwestern University, Chicago, IL 60611, USA
| |
Collapse
|
80
|
Lee GH, Lee YR, Kim H, Kwon DA, Kim H, Yang C, Choi SQ, Park S, Jeong JW, Park S. Rapid meniscus-guided printing of stable semi-solid-state liquid metal microgranular-particle for soft electronics. Nat Commun 2022; 13:2643. [PMID: 35551193 PMCID: PMC9098628 DOI: 10.1038/s41467-022-30427-z] [Citation(s) in RCA: 29] [Impact Index Per Article: 14.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/07/2021] [Accepted: 04/28/2022] [Indexed: 12/14/2022] Open
Abstract
Liquid metal is being regarded as a promising material for soft electronics owing to its distinct combination of high electrical conductivity comparable to that of metals and exceptional deformability derived from its liquid state. However, the applicability of liquid metal is still limited due to the difficulty in simultaneously achieving its mechanical stability and initial conductivity. Furthermore, reliable and rapid patterning of stable liquid metal directly on various soft substrates at high-resolution remains a formidable challenge. In this work, meniscus-guided printing of ink containing polyelectrolyte-attached liquid metal microgranular-particle in an aqueous solvent to generate semi-solid-state liquid metal is presented. Liquid metal microgranular-particle printed in the evaporative regime is mechanically stable, initially conductive, and patternable down to 50 μm on various substrates. Demonstrations of the ultrastretchable (~500% strain) electrical circuit, customized e-skin, and zero-waste ECG sensor validate the simplicity, versatility, and reliability of this manufacturing strategy, enabling broad utility in the development of advanced soft electronics. In this article, meniscus-guided printing of polyelectrolyte-attached liquid metal particles to simultaneously achieve mechanical stability and initial electrical conductivity at high resolution is introduced.
Collapse
Affiliation(s)
- Gun-Hee Lee
- Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea.,School of Electrical Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea
| | - Ye Rim Lee
- Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea
| | - Hanul Kim
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea
| | - Do A Kwon
- Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea
| | - Hyeonji Kim
- Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea
| | - Congqi Yang
- Department of Bio and Brain Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea
| | - Siyoung Q Choi
- Department of Chemical and Biomolecular Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea.,KAIST Institute for the NanoCentury, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, 34141, Republic of Korea
| | - Seongjun Park
- Department of Bio and Brain Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea.,KAIST Institute for Health Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea
| | - Jae-Woong Jeong
- School of Electrical Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea. .,KAIST Institute for Health Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea.
| | - Steve Park
- Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology (KAIST), 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea. .,KAIST Institute for Health Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon, 34141, Republic of Korea.
| |
Collapse
|
81
|
Stretchable, Multi-Layered Stack Antenna for Smart/Wearable Electronic Applications. MATERIALS 2022; 15:ma15093275. [PMID: 35591608 PMCID: PMC9105753 DOI: 10.3390/ma15093275] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 04/06/2022] [Revised: 04/27/2022] [Accepted: 05/02/2022] [Indexed: 12/10/2022]
Abstract
The development of microelectronics has been achieved by improving its performance through miniaturization. This was possible through the development of silicon-based semiconductor process technology, but recently, the demand for wearable or flexible devices has increased. These devices are made using various functional elements based on materials that are difficult to utilize with semiconductor devices that contain existing hard silicon-based materials and are bent or flexibly stretched. In this study, wireless antennas suitable for wearable devices were implemented in a stretchable form. It was possible to stably receive a wireless signal, even with a strain of 20% or more, and power light-emitting diodes (LEDs), microheaters, etc. By devising a multi-layered stack antenna without the existing semiconductor process, it was possible to improve the antenna’s reception performance. It is expected that this can be applied in various ways to smart wireless sensors and wearable biomedical devices using the near-field communication (NFC) of smartphones.
Collapse
|
82
|
Lan L, Ping J, Xiong J, Ying Y. Sustainable Natural Bio-Origin Materials for Future Flexible Devices. ADVANCED SCIENCE (WEINHEIM, BADEN-WURTTEMBERG, GERMANY) 2022; 9:e2200560. [PMID: 35322600 PMCID: PMC9130888 DOI: 10.1002/advs.202200560] [Citation(s) in RCA: 21] [Impact Index Per Article: 10.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/28/2022] [Revised: 02/27/2022] [Indexed: 05/12/2023]
Abstract
Flexible devices serve as important intelligent interfaces in various applications involving health monitoring, biomedical therapies, and human-machine interfacing. To address the concern of electronic waste caused by the increasing usage of electronic devices based on synthetic polymers, bio-origin materials that possess environmental benignity as well as sustainability offer new opportunities for constructing flexible electronic devices with higher safety and environmental adaptivity. Herein, the bio-source and unique molecular structures of various types of natural bio-origin materials are briefly introduced. Their properties and processing technologies are systematically summarized. Then, the recent progress of these materials for constructing emerging intelligent flexible electronic devices including energy harvesters, energy storage devices, and sensors are introduced. Furthermore, the applications of these flexible electronic devices including biomedical implants, artificial e-skin, and environmental monitoring are summarized. Finally, future challenges and prospects for developing high-performance bio-origin material-based flexible devices are discussed. This review aims to provide a comprehensive and systematic summary of the latest advances in the natural bio-origin material-based flexible devices, which is expected to offer inspirations for exploitation of green flexible electronics, bridging the gap in future human-machine-environment interactions.
Collapse
Affiliation(s)
- Lingyi Lan
- Laboratory of Agricultural Information Intelligent SensingSchool of Biosystems Engineering and Food ScienceZhejiang UniversityHangzhouZhejiang310058China
- Key Laboratory of Intelligent Equipment and Robotics for Agriculture of Zhejiang ProvinceHangzhouZhejiang310058China
| | - Jianfeng Ping
- Laboratory of Agricultural Information Intelligent SensingSchool of Biosystems Engineering and Food ScienceZhejiang UniversityHangzhouZhejiang310058China
- Key Laboratory of Intelligent Equipment and Robotics for Agriculture of Zhejiang ProvinceHangzhouZhejiang310058China
| | - Jiaqing Xiong
- Innovation Center for Textile Science and TechnologyDonghua University2999 North Renmin RoadShanghai201620China
| | - Yibin Ying
- Laboratory of Agricultural Information Intelligent SensingSchool of Biosystems Engineering and Food ScienceZhejiang UniversityHangzhouZhejiang310058China
- Key Laboratory of Intelligent Equipment and Robotics for Agriculture of Zhejiang ProvinceHangzhouZhejiang310058China
| |
Collapse
|
83
|
Wei S, Jiang J, Sun L, Li J, Tao TH, Zhou Z. A Hierarchically Encoded Data Storage Device with Controlled Transiency. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2201035. [PMID: 35293037 DOI: 10.1002/adma.202201035] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 01/31/2022] [Revised: 02/28/2022] [Indexed: 06/14/2023]
Abstract
In the era of information explosion, high-security and high-capacity data storage technology attracts more and more attention. Physically transient electronics, a form of electronics that can physically disappear with precisely controlled degradation behaviors, paves the way for secure data storage. Herein, the authors report a silk-based hierarchically encoded data storage device (HEDSD) with controlled transiency. The HEDSD can store electronic, photonic, and optical information simultaneously by synergistically integrating a resistive switching memory (ReRAM), a terahertz metamaterial device, and a diffractive optical element, respectively. These three data storage units have shared materials and structures but diverse encoding mechanisms, which increases the degree of complexity and capacity of stored information. Silk plays an important role as a building material in the HEDSD thanks to its excellent mechanical, optical, and electrical properties and controlled transiency as a naturally extracted protein. By controlling the degradation rate of storage units of the silk-based HEDSD, different degradation modes of the HEDSD, and multilevel information encryption/decryption have been realized. Compared with the conventional memory devices, as-reported silk-based HEDSD can store multilevel complex information and realize multilevel information encryption and decryption, which is highly desirable to fulfill the future demands of secure memory systems and implantable storage devices.
Collapse
Affiliation(s)
- Shuai Wei
- State Key Laboratory of Transducer Technology, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, 200050, China
- School of Graduate Study, University of Chinese Academy of Sciences, Beijing, 100049, China
| | - Jianjuan Jiang
- State Key Laboratory of Transducer Technology, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, 200050, China
| | - Long Sun
- State Key Laboratory of Transducer Technology, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, 200050, China
| | - Jianxing Li
- School of Information and Communications Engineering, Xi'an Jiaotong University, Xi'an, 710049, China
| | - Tiger H Tao
- State Key Laboratory of Transducer Technology, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, 200050, China
- School of Graduate Study, University of Chinese Academy of Sciences, Beijing, 100049, China
- Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing, 100049, China
- 2020 X-Lab, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, 200050, China
- School of Physical Science and Technology, ShanghaiTech University, Shanghai, 200031, China
- Center for Excellence in Brain Science and Intelligence Technology, Chinese Academy of Sciences, Shanghai, 200031, China
| | - Zhitao Zhou
- State Key Laboratory of Transducer Technology, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai, 200050, China
| |
Collapse
|
84
|
Fernandes C, Taurino I. Biodegradable Molybdenum (Mo) and Tungsten (W) Devices: One Step Closer towards Fully-Transient Biomedical Implants. SENSORS 2022; 22:s22083062. [PMID: 35459047 PMCID: PMC9027146 DOI: 10.3390/s22083062] [Citation(s) in RCA: 11] [Impact Index Per Article: 5.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 02/27/2022] [Revised: 04/08/2022] [Accepted: 04/12/2022] [Indexed: 01/03/2023]
Abstract
Close monitoring of vital physiological parameters is often key in following the evolution of certain medical conditions (e.g., diabetes, infections, post-operative status or post-traumatic injury). The allocation of trained medical staff and specialized equipment is, therefore, necessary and often translates into a clinical and economic burden on modern healthcare systems. As a growing field, transient electronics may establish fully bioresorbable medical devices capable of remote real-time monitoring of therapeutically relevant parameters. These devices could alert remote medical personnel in case of any anomaly and fully disintegrate in the body without a trace. Unfortunately, the need for a multitude of biodegradable electronic components (power supplies, wires, circuitry) in addition to the electrochemical biosensing interface has halted the arrival of fully bioresorbable electronically active medical devices. In recent years molybdenum (Mo) and tungsten (W) have drawn increasing attention as promising candidates for the fabrication of both energy-powered active (e.g., transistors and integrated circuits) and passive (e.g., resistors and capacitors) biodegradable electronic components. In this review, we discuss the latest Mo and W-based dissolvable devices for potential biomedical applications and how these soluble metals could pave the way towards next-generation fully transient implantable electronic systems.
Collapse
Affiliation(s)
- Catarina Fernandes
- Micro and Nano-Systems (MNS), Department of Electrical Engineering (Micro- and Nano Systems), Katholieke Universiteit Leuven (KU Leuven), 3000 Leuven, Belgium;
- Correspondence:
| | - Irene Taurino
- Micro and Nano-Systems (MNS), Department of Electrical Engineering (Micro- and Nano Systems), Katholieke Universiteit Leuven (KU Leuven), 3000 Leuven, Belgium;
- Semiconductor Physics, Department of Physics and Astronomy (Semiconductor Physics), Katholieke Universiteit Leuven (KU Leuven), 3000 Leuven, Belgium
| |
Collapse
|
85
|
Park W, Nguyen VP, Jeon Y, Kim B, Li Y, Yi J, Kim H, Leem JW, Kim YL, Kim DR, Paulus YM, Lee CH. Biodegradable silicon nanoneedles for ocular drug delivery. SCIENCE ADVANCES 2022; 8:eabn1772. [PMID: 35353558 PMCID: PMC8967230 DOI: 10.1126/sciadv.abn1772] [Citation(s) in RCA: 28] [Impact Index Per Article: 14.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 11/08/2021] [Accepted: 02/08/2022] [Indexed: 06/14/2023]
Abstract
Ocular drug delivery remains a grand challenge due to the complex structure of the eye. Here, we introduce a unique platform of ocular drug delivery through the integration of silicon nanoneedles with a tear-soluble contact lens. The silicon nanoneedles can penetrate into the cornea in a minimally invasive manner and then undergo gradual degradation over the course of months, enabling painless and long-term sustained delivery of ocular drugs. The tear-soluble contact lens can fit a variety of corneal sizes and then quickly dissolve in tear fluid within a minute, enabling an initial burst release of anti-inflammatory drugs. We demonstrated the utility of this platform in effectively treating a chronic ocular disease, such as corneal neovascularization, in a rabbit model without showing a notable side effect over current standard therapies. This platform could also be useful in treating other chronic ocular diseases.
Collapse
Affiliation(s)
- Woohyun Park
- School of Mechanical Engineering, Purdue University, West Lafayette, IN 47907, USA
| | - Van Phuc Nguyen
- Department of Ophthalmology and Visual Sciences, University of Michigan, Ann Arbor, MI 48105, USA
| | - Yale Jeon
- School of Mechanical Engineering, Hanyang University, Seoul 04763, Republic of Korea
| | - Bongjoong Kim
- Weldon School of Biomedical Engineering, Purdue University, West Lafayette, IN 47907, USA
- Department of Mechanical and System Design Engineering, Hongik University, Seoul 04066, Republic of Korea
| | - Yanxiu Li
- Department of Ophthalmology and Visual Sciences, University of Michigan, Ann Arbor, MI 48105, USA
| | - Jonghun Yi
- School of Mechanical Engineering, Hanyang University, Seoul 04763, Republic of Korea
| | - Hyungjun Kim
- Weldon School of Biomedical Engineering, Purdue University, West Lafayette, IN 47907, USA
- Department of Applied Chemistry, Kumoh National Institute of Technology, Gumi, Gyeongbuk 39177, Republic of Korea
| | - Jung Woo Leem
- Weldon School of Biomedical Engineering, Purdue University, West Lafayette, IN 47907, USA
| | - Young L. Kim
- Weldon School of Biomedical Engineering, Purdue University, West Lafayette, IN 47907, USA
| | - Dong Rip Kim
- School of Mechanical Engineering, Hanyang University, Seoul 04763, Republic of Korea
| | - Yannis M. Paulus
- Department of Ophthalmology and Visual Sciences, University of Michigan, Ann Arbor, MI 48105, USA
- Department of Biomedical Engineering, University of Michigan, Ann Arbor, MI 48105, USA
| | - Chi Hwan Lee
- School of Mechanical Engineering, Purdue University, West Lafayette, IN 47907, USA
- Weldon School of Biomedical Engineering, Purdue University, West Lafayette, IN 47907, USA
- Department of Materials Engineering, Purdue University, West Lafayette, IN 47907, USA
- Birck Nanotechnology Center, Purdue University, West Lafayette, IN 47907, USA
| |
Collapse
|
86
|
Kim H, Kim MJ, Kwon YW, Jeon S, Lee S, Kim C, Choi BT, Shin Y, Hong SW, Shin HK. Benefits of a Skull-Interfaced Flexible and Implantable Multilight Emitting Diode Array for Photobiomodulation in Ischemic Stroke. ADVANCED SCIENCE (WEINHEIM, BADEN-WURTTEMBERG, GERMANY) 2022; 9:e2104629. [PMID: 35076161 PMCID: PMC9008794 DOI: 10.1002/advs.202104629] [Citation(s) in RCA: 10] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/18/2021] [Revised: 01/08/2022] [Indexed: 05/05/2023]
Abstract
Photobiomodulation (PBM) has received attention due to its potential for improving tissue function and enhancing regeneration in stroke. A lightweight, compact, and simple system of miniaturized electronic devices consisting of packaged light-emitting diodes (LEDs) that incorporates a flexible substrate for in vivo brain PBM in a mouse model is developed. Using this device platform, the preventive and therapeutic effects of PBM affixed to the exposed skull of mice in the photothrombosis and middle cerebral artery occlusion stroke model are evaluated. Among the wavelength range of 630, 850, and 940 nm LED array, the PBM with 630-nm LED array is proved to be the most effective for reducing the infarction volume and neurological impairment after ischemic stroke. Moreover, the PBM with 630 nm LED array remarkably improves the capability of spatial learning and memory in the chronic poststroke phase, attenuates AIM2 inflammasome activation and inflammasome-mediated pyroptosis, and modulates microglial polarization in the hippocampus and cortex 7 days following ischemic stroke. Thus, PBM may prevent tissue and functional damage in acute ischemic injury, thereby attenuating the development of cognitive impairment after stroke.
Collapse
Affiliation(s)
- Hyunha Kim
- Department of Korean Medical ScienceGraduate Training Program of Korean Medical Therapeutics for Healthy‐AgingSchool of Korean MedicinePusan National UniversityYangsan50612Republic of Korea
- Department of Pharmacology and NeuroscienceCreighton University School of MedicineOmahaNE68178USA
| | - Min Jae Kim
- Department of Korean Medical ScienceGraduate Training Program of Korean Medical Therapeutics for Healthy‐AgingSchool of Korean MedicinePusan National UniversityYangsan50612Republic of Korea
| | - Young Woo Kwon
- Department of Nano‐Fusion TechnologyCollege of Nanoscience & NanotechnologyPusan National UniversityBusan46241Republic of Korea
| | - Sangheon Jeon
- Department of Congo‐Mechatronics EngineeringDepartment of Optics and Mechatronics EngineeringCollege of Nanoscience & NanotechnologyPusan National UniversityBusan46241Republic of Korea
| | - Seo‐Yeon Lee
- Department of PharmacologyWonkwang University School of MedicineIksan54538Republic of Korea
| | - Chang‐Seok Kim
- Department of Congo‐Mechatronics EngineeringDepartment of Optics and Mechatronics EngineeringCollege of Nanoscience & NanotechnologyPusan National UniversityBusan46241Republic of Korea
| | - Byung Tae Choi
- Department of Korean Medical ScienceGraduate Training Program of Korean Medical Therapeutics for Healthy‐AgingSchool of Korean MedicinePusan National UniversityYangsan50612Republic of Korea
| | - Yong‐Il Shin
- Department of Rehabilitation MedicineSchool of MedicinePusan National UniversityYangsan50612Republic of Korea
| | - Suck Won Hong
- Department of Congo‐Mechatronics EngineeringDepartment of Optics and Mechatronics EngineeringCollege of Nanoscience & NanotechnologyPusan National UniversityBusan46241Republic of Korea
| | - Hwa Kyoung Shin
- Department of Korean Medical ScienceGraduate Training Program of Korean Medical Therapeutics for Healthy‐AgingSchool of Korean MedicinePusan National UniversityYangsan50612Republic of Korea
| |
Collapse
|
87
|
Yang SM, Shim JH, Cho HU, Jang TM, Ko GJ, Shim J, Kim TH, Zhu J, Park S, Kim YS, Joung SY, Choe JC, Shin JW, Lee JH, Kang YM, Cheng H, Jung Y, Lee CH, Jang DP, Hwang SW. Hetero-Integration of Silicon Nanomembranes with 2D Materials for Bioresorbable, Wireless Neurochemical System. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2108203. [PMID: 35073597 DOI: 10.1002/adma.202108203] [Citation(s) in RCA: 23] [Impact Index Per Article: 11.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 10/13/2021] [Revised: 01/14/2022] [Indexed: 06/14/2023]
Abstract
Although neurotransmitters are key substances closely related to evaluating degenerative brain diseases as well as regulating essential functions in the body, many research efforts have not been focused on direct observation of such biochemical messengers, rather on monitoring relatively associated physical, mechanical, and electrophysiological parameters. Here, a bioresorbable silicon-based neurochemical analyzer incorporated with 2D transition metal dichalcogenides is introduced as a completely implantable brain-integrated system that can wirelessly monitor time-dynamic behaviors of dopamine and relevant parameters in a simultaneous mode. An extensive range of examinations of molybdenum/tungsten disulfide (MoS2 /WS2 ) nanosheets and catalytic iron nanoparticles (Fe NPs) highlights the underlying mechanisms of strong chemical and target-specific responses to the neurotransmitters, along with theoretical modeling tools. Systematic characterizations demonstrate reversible, stable, and long-term operational performances of the degradable bioelectronics with excellent sensitivity and selectivity over those of non-dissolvable counterparts. A complete set of in vivo experiments with comparative analysis using carbon-fiber electrodes illustrates the capability for potential use as a clinically accessible tool to associated neurodegenerative diseases.
Collapse
Affiliation(s)
- Seung Min Yang
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Jae Hyung Shim
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Hyun-U Cho
- Department of Biomedical Engineering, Hanyang University, 222, Wangsimni-ro, Seongdong-gu, Seoul, 04763, Republic of Korea
| | - Tae-Min Jang
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Gwan-Jin Ko
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Jeongeun Shim
- Department of Biomedical Engineering, Hanyang University, 222, Wangsimni-ro, Seongdong-gu, Seoul, 04763, Republic of Korea
| | - Tae Hee Kim
- Center for Biomaterials, Biomedical Research Institute, Korea Institute of Science and Technology (KIST), Seoul, 02792, Republic of Korea
| | - Jia Zhu
- Department of Engineering Science and Mechanics, The Pennsylvania State University, University Park, Pennsylvania, 16802, USA
| | - Sangun Park
- Center for Biomaterials, Biomedical Research Institute, Korea Institute of Science and Technology (KIST), Seoul, 02792, Republic of Korea
- Institute of Animal Molecular Biotechnology and Department of Biotechnology, College of Life Sciences and Biotechnology, Korea University, 145, Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Yoon Seok Kim
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Su-Yeon Joung
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Jong Chan Choe
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Jeong-Woong Shin
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Joong Hoon Lee
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
| | - Yu Min Kang
- Department of Biomedical Engineering, Hanyang University, 222, Wangsimni-ro, Seongdong-gu, Seoul, 04763, Republic of Korea
| | - Huanyu Cheng
- Department of Engineering Science and Mechanics, The Pennsylvania State University, University Park, Pennsylvania, 16802, USA
| | - Youngmee Jung
- Center for Biomaterials, Biomedical Research Institute, Korea Institute of Science and Technology (KIST), Seoul, 02792, Republic of Korea
- School of Electrical and Electronic Engineering, Yonsei University, Seoul, 03722, Republic of Korea
- Yonsei-KIST Convergence Research Institute, Yonsei University, Seoul, 03722, Republic of Korea
| | - Chul-Ho Lee
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
- Department of Integrative Energy Engineering, Korea University, Seoul, 02841, Republic of Korea
| | - Dong Pyo Jang
- Department of Biomedical Engineering, Hanyang University, 222, Wangsimni-ro, Seongdong-gu, Seoul, 04763, Republic of Korea
| | - Suk-Won Hwang
- KU-KIST Graduate School of Converging Science and Technology, Korea University, 145 Anam-ro, Seongbuk-gu, Seoul, 02841, Republic of Korea
- Department of Integrative Energy Engineering, Korea University, Seoul, 02841, Republic of Korea
| |
Collapse
|
88
|
Xia F, Xia T, Xiang L, Liu F, Jia W, Liang X, Hu Y. High-Performance Carbon Nanotube-Based Transient Complementary Electronics. ACS APPLIED MATERIALS & INTERFACES 2022; 14:12515-12522. [PMID: 35230800 DOI: 10.1021/acsami.1c23134] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/14/2023]
Abstract
Transient electronics is an emerging class of electronic devices that can physically degrade or disintegrate after a stable period of service, showing a vast prospect in applications of "green" consumer electronics, hardware-secure devices, medical implants, etc. Complementary metal-oxide-semiconductor (CMOS) technology is dominant in integrated circuit design for its advantages of low static power consumption, high noise immunity, and simple design layout, which also work and are highly preferred for transient electronics. However, the performance of complementary transient electronics is severely restricted by the confined selection of transient materials and compatible fabrication strategies. Here, we report the realization of high-performance transient complementary electronics based on carbon nanotube thin films via a reliable electrostatic doping method. Under a low operating voltage of 2 V, on a 1.5 μm-thick water-soluble substrate made of poly(vinyl alcohol), the width-normalized on-state currents of the p-type and n-type transient thin-film transistors (TFTs) reach 4.5 and 4.7 μA/μm, and the width-normalized transconductances reach 2.8 and 3.7 μS/μm, respectively. Meanwhile, these TFTs show small subthreshold swings no more than 108 mV/dec and current on/off ratios above 106 with good uniformity. Transient CMOS inverters, as basic circuit components, are demonstrated with a voltage gain of 24 and a high noise immunity of 67.4%. Finally, both the degradation of the active components and the disintegration of the functional system are continuously monitored with nontraceable remains after 10 and 5 h, respectively.
Collapse
Affiliation(s)
- Fan Xia
- Key Laboratory for the Physics and Chemistry of Nanodevices, Center for Carbon-Based Electronics, and School of Electronics, Peking University, Beijing 100871, China
- Academy for Advanced Interdisciplinary Studies, Peking University, Beijing 100871, China
| | - Tian Xia
- Key Laboratory for the Physics and Chemistry of Nanodevices, Center for Carbon-Based Electronics, and School of Electronics, Peking University, Beijing 100871, China
- Academy for Advanced Interdisciplinary Studies, Peking University, Beijing 100871, China
| | - Li Xiang
- Key Laboratory for the Physics and Chemistry of Nanodevices, Center for Carbon-Based Electronics, and School of Electronics, Peking University, Beijing 100871, China
- College of Materials and Engineering, Hunan University, Changsha 410082, China
| | - Fang Liu
- Key Laboratory for the Physics and Chemistry of Nanodevices, Center for Carbon-Based Electronics, and School of Electronics, Peking University, Beijing 100871, China
| | - Weijie Jia
- Key Laboratory for the Physics and Chemistry of Nanodevices, Center for Carbon-Based Electronics, and School of Electronics, Peking University, Beijing 100871, China
| | - Xuelei Liang
- Key Laboratory for the Physics and Chemistry of Nanodevices, Center for Carbon-Based Electronics, and School of Electronics, Peking University, Beijing 100871, China
| | - Youfan Hu
- Key Laboratory for the Physics and Chemistry of Nanodevices, Center for Carbon-Based Electronics, and School of Electronics, Peking University, Beijing 100871, China
- Academy for Advanced Interdisciplinary Studies, Peking University, Beijing 100871, China
| |
Collapse
|
89
|
Balakrishnan G, Song J, Mou C, Bettinger CJ. Recent Progress in Materials Chemistry to Advance Flexible Bioelectronics in Medicine. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2106787. [PMID: 34751987 PMCID: PMC8917047 DOI: 10.1002/adma.202106787] [Citation(s) in RCA: 24] [Impact Index Per Article: 12.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/27/2021] [Revised: 10/15/2021] [Indexed: 05/09/2023]
Abstract
Designing bioelectronic devices that seamlessly integrate with the human body is a technological pursuit of great importance. Bioelectronic medical devices that reliably and chronically interface with the body can advance neuroscience, health monitoring, diagnostics, and therapeutics. Recent major efforts focus on investigating strategies to fabricate flexible, stretchable, and soft electronic devices, and advances in materials chemistry have emerged as fundamental to the creation of the next generation of bioelectronics. This review summarizes contemporary advances and forthcoming technical challenges related to three principal components of bioelectronic devices: i) substrates and structural materials, ii) barrier and encapsulation materials, and iii) conductive materials. Through notable illustrations from the literature, integration and device fabrication strategies and associated challenges for each material class are highlighted.
Collapse
Affiliation(s)
| | - Jiwoo Song
- Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA, 15213, USA
| | - Chenchen Mou
- Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, PA, 15213, USA
| | | |
Collapse
|
90
|
Choi JH, Choi M, Ho TS, Kim S, Choi S, Choi SH, Byun KM. Biological SERS-active sensor platform based on flexible silk fibroin film and gold nanoislands. OPTICS EXPRESS 2022; 30:7782-7792. [PMID: 35299533 DOI: 10.1364/oe.452665] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 12/29/2021] [Accepted: 02/10/2022] [Indexed: 05/24/2023]
Abstract
In contrast to conventional surface-enhanced Raman scattering (SERS) platforms implemented on non-biological substrates, silk fibroin has the unique advantages of long-term biosafety and controllable biodegradability for in vitro and in vivo biomedical applications, as well as flexibility and process-compatibility. In this study, a silk fibroin film was developed to fabricate a flexible SERS sensor template with nanogap-rich gold nanoislands. The proposed biological SERS platform presents fairly good enhancements in detection performance such as detection limit, sensitivity, and signal-to-noise ratio. In particular, the sensitivity improvement was by more than 10 times compared to that of the counterpart sample, and an excellent spatial reproducibility of 2.8% was achieved. In addition, the near-field calculation results were consistent with the experimental results, and the effect of surface roughness of the silk substrate was investigated in a quantitative way. It is believed that biological SERS-active sensors could provide the potential for highly sensitive, cost-effective, and easily customizable nanophotonic platforms that include new capabilities for future healthcare devices.
Collapse
|
91
|
Chiong JA, Zheng Y, Zhang S, Ma G, Wu Y, Ngaruka G, Lin Y, Gu X, Bao Z. Impact of Molecular Design on Degradation Lifetimes of Degradable Imine-Based Semiconducting Polymers. J Am Chem Soc 2022; 144:3717-3726. [PMID: 35179880 DOI: 10.1021/jacs.1c12845] [Citation(s) in RCA: 7] [Impact Index Per Article: 3.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/29/2022]
Abstract
Transient electronics are a rapidly emerging field due to their potential applications in the environment and human health. Recently, a few studies have incorporated acid-labile imine bonds into polymer semiconductors to impart transience; however, understanding of the structure-degradation property relationships of these polymers is limited. In this study, we systematically design and characterize a series of fully degradable diketopyrrolopyrrole-based polymers with engineered sidechains to investigate the impact of several molecular design parameters on the degradation lifetimes of these polymers. By monitoring degradation kinetics via ultraviolet-visible spectroscopy, we reveal that polymer degradation in solution is aggregation-dependent based on the branching point and Mn, with accelerated degradation rates facilitated by decreasing aggregation. Additionally, increasing the hydrophilicity of the polymers promotes water diffusion and therefore acid hydrolysis of the imine bonds along the polymer backbone. The aggregation properties and degradation lifetimes of these polymers rely heavily on solvent, with polymers in chlorobenzene taking six times as long to degrade as in chloroform. We develop a new method for quantifying the degradation of polymers in the thin film and observe that similar factors and considerations (e.g., interchain order, crystallite size, and hydrophilicity) used for designing high-performance semiconductors impact the degradation of imine-based polymer semiconductors. We found that terpolymerization serves as an attractive approach for achieving degradable semiconductors with both good charge transport and tuned degradation properties. This study provides crucial principles for the molecular design of degradable semiconducting polymers, and we anticipate that these findings will expedite progress toward transient electronics with controlled lifetimes.
Collapse
Affiliation(s)
- Jerika A Chiong
- Department of Chemistry, Stanford University, Stanford, California 94305, United States.,Department of Chemical Engineering, Stanford University, Stanford, California 94305, United States
| | - Yu Zheng
- Department of Chemistry, Stanford University, Stanford, California 94305, United States.,Department of Chemical Engineering, Stanford University, Stanford, California 94305, United States
| | - Song Zhang
- Department of Chemical Engineering, Stanford University, Stanford, California 94305, United States
| | - Guorong Ma
- School of Polymer Science and Engineering, The University of Southern Mississippi, Hattiesburg, Mississippi 39406, United States
| | - Yilei Wu
- Department of Chemical Engineering, Stanford University, Stanford, California 94305, United States
| | - Gradie Ngaruka
- Department of Chemical Engineering, Stanford University, Stanford, California 94305, United States
| | - Yangju Lin
- Department of Chemical Engineering, Stanford University, Stanford, California 94305, United States
| | - Xiaodan Gu
- School of Polymer Science and Engineering, The University of Southern Mississippi, Hattiesburg, Mississippi 39406, United States
| | - Zhenan Bao
- Department of Chemistry, Stanford University, Stanford, California 94305, United States.,Department of Chemical Engineering, Stanford University, Stanford, California 94305, United States
| |
Collapse
|
92
|
Pham PV, Bodepudi SC, Shehzad K, Liu Y, Xu Y, Yu B, Duan X. 2D Heterostructures for Ubiquitous Electronics and Optoelectronics: Principles, Opportunities, and Challenges. Chem Rev 2022; 122:6514-6613. [PMID: 35133801 DOI: 10.1021/acs.chemrev.1c00735] [Citation(s) in RCA: 102] [Impact Index Per Article: 51.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 02/07/2023]
Abstract
A grand family of two-dimensional (2D) materials and their heterostructures have been discovered through the extensive experimental and theoretical efforts of chemists, material scientists, physicists, and technologists. These pioneering works contribute to realizing the fundamental platforms to explore and analyze new physical/chemical properties and technological phenomena at the micro-nano-pico scales. Engineering 2D van der Waals (vdW) materials and their heterostructures via chemical and physical methods with a suitable choice of stacking order, thickness, and interlayer interactions enable exotic carrier dynamics, showing potential in high-frequency electronics, broadband optoelectronics, low-power neuromorphic computing, and ubiquitous electronics. This comprehensive review addresses recent advances in terms of representative 2D materials, the general fabrication methods, and characterization techniques and the vital role of the physical parameters affecting the quality of 2D heterostructures. The main emphasis is on 2D heterostructures and 3D-bulk (3D) hybrid systems exhibiting intrinsic quantum mechanical responses in the optical, valley, and topological states. Finally, we discuss the universality of 2D heterostructures with representative applications and trends for future electronics and optoelectronics (FEO) under the challenges and opportunities from physical, nanotechnological, and material synthesis perspectives.
Collapse
Affiliation(s)
- Phuong V Pham
- School of Micro-Nano Electronics, Hangzhou Global Scientific and Technological Innovation Center (HIC), Zhejiang University, Xiaoshan 311200, China.,State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027, China.,ZJU-UIUC Joint Institute, Zhejiang University, Jiaxing 314400, China
| | - Srikrishna Chanakya Bodepudi
- School of Micro-Nano Electronics, Hangzhou Global Scientific and Technological Innovation Center (HIC), Zhejiang University, Xiaoshan 311200, China.,State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027, China.,ZJU-UIUC Joint Institute, Zhejiang University, Jiaxing 314400, China
| | - Khurram Shehzad
- School of Micro-Nano Electronics, Hangzhou Global Scientific and Technological Innovation Center (HIC), Zhejiang University, Xiaoshan 311200, China.,State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027, China.,ZJU-UIUC Joint Institute, Zhejiang University, Jiaxing 314400, China
| | - Yuan Liu
- School of Physics and Electronics, Hunan University, Hunan 410082, China
| | - Yang Xu
- School of Micro-Nano Electronics, Hangzhou Global Scientific and Technological Innovation Center (HIC), Zhejiang University, Xiaoshan 311200, China.,State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027, China.,ZJU-UIUC Joint Institute, Zhejiang University, Jiaxing 314400, China
| | - Bin Yu
- School of Micro-Nano Electronics, Hangzhou Global Scientific and Technological Innovation Center (HIC), Zhejiang University, Xiaoshan 311200, China.,State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027, China.,ZJU-UIUC Joint Institute, Zhejiang University, Jiaxing 314400, China
| | - Xiangfeng Duan
- Department of Chemistry and Biochemistry, University of California, Los Angeles (UCLA), Los Angeles, California 90095-1569, United States
| |
Collapse
|
93
|
Li WD, Ke K, Jia J, Pu JH, Zhao X, Bao RY, Liu ZY, Bai L, Zhang K, Yang MB, Yang W. Recent Advances in Multiresponsive Flexible Sensors towards E-skin: A Delicate Design for Versatile Sensing. SMALL (WEINHEIM AN DER BERGSTRASSE, GERMANY) 2022; 18:e2103734. [PMID: 34825473 DOI: 10.1002/smll.202103734] [Citation(s) in RCA: 38] [Impact Index Per Article: 19.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 06/26/2021] [Revised: 09/16/2021] [Indexed: 05/07/2023]
Abstract
Multiresponsive flexile sensors with strain, temperature, humidity, and other sensing abilities serving as real electronic skin (e-skin) have manifested great application potential in flexible electronics, artificial intelligence (AI), and Internet of Things (IoT). Although numerous flexible sensors with sole sensing function have already been reported since the concept of e-skin, that mimics the sensing features of human skin, was proposed about a decade ago, the ones with more sensing capacities as new emergences are urgently demanded. However, highly integrated and highly sensitive flexible sensors with multiresponsive functions are becoming a big thrust for the detection of human body motions, physiological signals (e.g., skin temperature, blood pressure, electrocardiograms (ECG), electromyograms (EMG), sweat, etc.) and environmental stimuli (e.g., light, magnetic field, volatile organic compounds (VOCs)), which are vital to real-time and all-round human health monitoring and management. Herein, this review summarizes the design, manufacturing, and application of multiresponsive flexible sensors and presents the future challenges of fabricating these sensors for the next-generation e-skin and wearable electronics.
Collapse
Affiliation(s)
- Wu-Di Li
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Kai Ke
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Jin Jia
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Jun-Hong Pu
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Xing Zhao
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Rui-Ying Bao
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Zheng-Ying Liu
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Lu Bai
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Kai Zhang
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Ming-Bo Yang
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| | - Wei Yang
- College of Polymer Science and Engineering, State Key Laboratory of Polymer Materials Engineering, Sichuan University, Chengdu, Sichuan, 610065, China
| |
Collapse
|
94
|
Pandey S, Mastrangelo C. Towards Transient Electronics through Heat Triggered Shattering of Off-the-Shelf Electronic Chips. MICROMACHINES 2022; 13:mi13020242. [PMID: 35208366 PMCID: PMC8877697 DOI: 10.3390/mi13020242] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 12/31/2021] [Revised: 01/28/2022] [Accepted: 01/28/2022] [Indexed: 12/04/2022]
Abstract
With most of the critical data being stored in silicon (Si) based electronic devices, there is a need to develop such devices with a transient nature. Here, we have focused on developing a programmable and controllable heat triggered shattering transience mechanism for any off-the-shelf (OTS) Si microchip as a means to develop transient electronics which can then be safely and rapidly disabled on trigger when desired. This transience mechanism is based on irreversible and spontaneous propagation of cracks that are patterned on the back of the OTS chip in the form of grooves and then filled with thermally expandable (TE) material. Two types of TE materials were used in this study, commercially available microsphere particles and a developed elastomeric material. These materials expand >100 times their original volume on the application of heat which applies wedging stress of the groove boundaries and induces crack propagation resulting in the complete shattering of the OTS Si chip into tiny silicon pieces. Transience was controlled by temperature and can be triggered at ~160–190 °C. We also demonstrated the programmability of critical parameters such as transience time (0.35–12 s) and transience efficiency (5–60%) without the knowledge of material properties by modeling the swelling behavior using linear viscoelastic models.
Collapse
|
95
|
Degradation Study of Thin-Film Silicon Structures in a Cell Culture Medium. SENSORS 2022; 22:s22030802. [PMID: 35161547 PMCID: PMC8838160 DOI: 10.3390/s22030802] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 12/30/2021] [Revised: 01/18/2022] [Accepted: 01/19/2022] [Indexed: 11/16/2022]
Abstract
Thin-film silicon (Si)-based transient electronics represents an emerging technology that enables spontaneous dissolution, absorption and, finally, physical disappearance in a controlled manner under physiological conditions, and has attracted increasing attention in pertinent clinical applications such as biomedical implants for on-body sensing, disease diagnostics, and therapeutics. The degradation behavior of thin-film Si materials and devices is critically dependent on the device structure as well as the environment. In this work, we experimentally investigated the dissolution of planar Si thin films and micropatterned Si pillar arrays in a cell culture medium, and systematically analyzed the evolution of their topographical, physical, and chemical properties during the hydrolysis. We discovered that the cell culture medium significantly accelerates the degradation process, and Si pillar arrays present more prominent degradation effects by creating rougher surfaces, complicating surface states, and decreasing the electrochemical impedance. Additionally, the dissolution process leads to greatly reduced mechanical strength. Finally, in vitro cell culture studies demonstrate desirable biocompatibility of corroded Si pillars. The results provide a guideline for the use of thin-film Si materials and devices as transient implants in biomedicine.
Collapse
|
96
|
Zhou N, Ma L. Smart bioelectronics and biomedical devices. Biodes Manuf 2022; 5:1-5. [PMID: 35043079 PMCID: PMC8759059 DOI: 10.1007/s42242-021-00179-8] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/17/2021] [Accepted: 11/22/2021] [Indexed: 12/26/2022]
Affiliation(s)
- Nanjia Zhou
- Key Laboratory of 3D Micro/Nano Fabrication and Characterization of Zhejiang Province, School of Engineering, Westlake University, Hangzhou, 310024 China
- Institute of Advanced Technology, Westlake Institute for Advanced Study, Hangzhou, 310024 China
| | - Liang Ma
- State Key Laboratory of Fluid Power and Mechatronic Systems, Zhejiang University, Hangzhou, 310058 China
- School of Mechanical Engineering, Zhejiang University, Hangzhou, 310058 China
| |
Collapse
|
97
|
Lee DM, Rubab N, Hyun I, Kang W, Kim YJ, Kang M, Choi BO, Kim SW. Ultrasound-mediated triboelectric nanogenerator for powering on-demand transient electronics. SCIENCE ADVANCES 2022; 8:eabl8423. [PMID: 34995120 PMCID: PMC8741185 DOI: 10.1126/sciadv.abl8423] [Citation(s) in RCA: 23] [Impact Index Per Article: 11.5] [Reference Citation Analysis] [Abstract] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/06/2023]
Abstract
On-demand transient electronics, technologies referring subsequent material disintegration under well-defined triggering events and programmed time lines, offer exceptional clinical experiences in diagnosis, treatment, and rehabilitation. Despite potential benefits, such as the elimination of surgical device removal and reduction of long-term inimical effects, their use is limited by the nontransient conventional power supplies. Here, we report an ultrasound-mediated transient triboelectric nanogenerator (TENG) where ultrasound determines energy generation and degradation period. Our findings on finite element method simulation show that porous structures of the poly(3-hydroxybutyrate-co-3-hydroxyvalerate) play an essential role in the triggering transient process of our device under high-intensity ultrasound. Besides, the addition of polyethylene glycol improves triboelectric output performance; the voltage output increased by 58.5%, from 2.625 to 4.160 V. We successfully demonstrate the tunable transient performances by ex vivo experiment using a porcine tissue. This study provides insight into practical use of implantable TENGs based on ultrasound-triggered transient material design.
Collapse
Affiliation(s)
- Dong-Min Lee
- School of Advanced Materials Science and Engineering, Sungkyunkwan University (SKKU), Suwon 16419, Republic of Korea
| | - Najaf Rubab
- School of Advanced Institute of Nanotechnology (SAINT), Sungkyunkwan University (SKKU), Suwon 16419, Republic of Korea
| | - Inah Hyun
- School of Advanced Materials Science and Engineering, Sungkyunkwan University (SKKU), Suwon 16419, Republic of Korea
| | - Wooseok Kang
- School of Advanced Materials Science and Engineering, Sungkyunkwan University (SKKU), Suwon 16419, Republic of Korea
| | - Young-Jun Kim
- School of Advanced Materials Science and Engineering, Sungkyunkwan University (SKKU), Suwon 16419, Republic of Korea
| | - Minki Kang
- School of Advanced Materials Science and Engineering, Sungkyunkwan University (SKKU), Suwon 16419, Republic of Korea
| | - Byung Ok Choi
- Department of Neurology, Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul 06351, Republic of Korea
- Stem Cell and Regenerative Medicine Institute, Samsung Medical Center, Seoul 06351, Republic of Korea
- Samsung Advanced Institute for Health Sciences and Technology (SAIHST), Sungkyunkwan University (SKKU), Seoul 06351, Republic of Korea
| | - Sang-Woo Kim
- School of Advanced Materials Science and Engineering, Sungkyunkwan University (SKKU), Suwon 16419, Republic of Korea
- School of Advanced Institute of Nanotechnology (SAINT), Sungkyunkwan University (SKKU), Suwon 16419, Republic of Korea
- Samsung Advanced Institute for Health Sciences and Technology (SAIHST), Sungkyunkwan University (SKKU), Seoul 06351, Republic of Korea
- Corresponding author.
| |
Collapse
|
98
|
Sang M, Kang K, Zhang Y, Zhang H, Kim K, Cho M, Shin J, Hong JH, Kim T, Lee SK, Yeo WH, Lee JW, Lee T, Xu B, Yu KJ. Ultrahigh Sensitive Au-Doped Silicon Nanomembrane Based Wearable Sensor Arrays for Continuous Skin Temperature Monitoring with High Precision. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2105865. [PMID: 34750868 DOI: 10.1002/adma.202105865] [Citation(s) in RCA: 41] [Impact Index Per Article: 20.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/29/2021] [Revised: 10/29/2021] [Indexed: 06/13/2023]
Abstract
Monitoring the body temperature with high accuracy provides a fast, facile, yet powerful route about the human body in a wide range of health information standards. Here, the first ever ultrasensitive and stretchable gold-doped silicon nanomembrane (Au-doped SiNM) epidermal temperature sensor array is introduced. The ultrasensitivity is achieved by shifting freeze-out region to intrinsic region in carrier density and modulation of fermi energy level of p-type SiNM through the development of a novel gold-doping strategy. The Au-doped SiNM is readily transferred onto an ultrathin polymer layer with a well-designed serpentine mesh structure, capable of being utilized as an epidermal temperature sensor array. Measurements in vivo and in vitro show temperature coefficient of resistance as high as -37270.72 ppm °C-1 , 22 times higher than existing metal-based temperature sensors with similar structures, and one of the highest thermal sensitivity among the inorganic material based temperature sensors. Applications in the continuous monitoring of body temperature and respiration rate during exercising are demonstrated with a successful capture of information. This work lays a foundation for monitoring body temperature, potentially useful for precision diagnosis (e.g., continuous monitoring body temperature in coronavirus disease 2019 cases) and management of disease relevance to body temperature in healthcare.
Collapse
Affiliation(s)
- Mingyu Sang
- Functional Bio-integrated Electronics and Energy Management Lab, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
| | - Kyowon Kang
- Functional Bio-integrated Electronics and Energy Management Lab, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
| | - Yue Zhang
- Xu Research Group, Department of Mechanical and Aerospace Engineering, University of Virginia, Charlottesville, VA, 22904, USA
| | - Haozhe Zhang
- Xu Research Group, Department of Mechanical and Aerospace Engineering, University of Virginia, Charlottesville, VA, 22904, USA
| | - Kiho Kim
- Functional Bio-integrated Electronics and Energy Management Lab, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
| | - Myeongki Cho
- Functional Bio-integrated Electronics and Energy Management Lab, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
| | - Jongwoon Shin
- Functional Bio-integrated Electronics and Energy Management Lab, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
| | - Jung-Hoon Hong
- Functional Bio-integrated Electronics and Energy Management Lab, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
| | - Taemin Kim
- Functional Bio-integrated Electronics and Energy Management Lab, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
| | - Shin Kyu Lee
- Functional Oxide Laboratory, Department of Electrical Engineering, Gachon University, 1342 Seongam-daero, Sujeong-gu, Seongnam-si, Gyeonggi-do, 13120, Republic of Korea
| | - Woon-Hong Yeo
- Bio-Interfaced Translational Nanoengineering Group, George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA, 30332, USA
| | - Jung Woo Lee
- Energy Materials for Soft Electronics Laboratory, School of Materials Science and Engineering, Pusan National University, Busan, 46241, Republic of Korea
| | - Taeyoon Lee
- YU-KIST Institute, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
- NanoBio Device Laboratory, School of Electrical and Electronic Engineering, Yonsei University, Seodaemungu, Seoul, 03722, Republic of Korea
| | - Baoxing Xu
- Xu Research Group, Department of Mechanical and Aerospace Engineering, University of Virginia, Charlottesville, VA, 22904, USA
| | - Ki Jun Yu
- Functional Bio-integrated Electronics and Energy Management Lab, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
- YU-KIST Institute, School of Electrical and Electronic Engineering, Yonsei University, 50 Yonsei-ro, Seodaemungu, Seoul, 03722, Republic of Korea
| |
Collapse
|
99
|
Li C, Wu J, Shi H, Xia Z, Sahoo JK, Yeo J, Kaplan DL. Fiber-Based Biopolymer Processing as a Route toward Sustainability. ADVANCED MATERIALS (DEERFIELD BEACH, FLA.) 2022; 34:e2105196. [PMID: 34647374 PMCID: PMC8741650 DOI: 10.1002/adma.202105196] [Citation(s) in RCA: 44] [Impact Index Per Article: 22.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 07/06/2021] [Revised: 09/04/2021] [Indexed: 05/02/2023]
Abstract
Some of the most abundant biomass on earth is sequestered in fibrous biopolymers like cellulose, chitin, and silk. These types of natural materials offer unique and striking mechanical and functional features that have driven strong interest in their utility for a range of applications, while also matching environmental sustainability needs. However, these material systems are challenging to process in cost-competitive ways to compete with synthetic plastics due to the limited options for thermal processing. This results in the dominance of solution-based processing for fibrous biopolymers, which presents challenges for scaling, cost, and consistency in outcomes. However, new opportunities to utilize thermal processing with these types of biopolymers, as well as fibrillation approaches, can drive renewed opportunities to bridge this gap between synthetic plastic processing and fibrous biopolymers, while also holding sustainability goals as critical to long-term successful outcomes.
Collapse
Affiliation(s)
- Chunmei Li
- Department of Biomedical Engineering, Tufts University, Medford, MA 02155, USA
| | - Junqi Wu
- Department of Biomedical Engineering, Tufts University, Medford, MA 02155, USA
| | - Haoyuan Shi
- Sibley School of Mechanical and Aerospace Engineering, Cornell University, Ithaca NY 14853, USA
| | - Zhiyu Xia
- Department of Biomedical Engineering, Tufts University, Medford, MA 02155, USA
| | - Jugal Kishore Sahoo
- Department of Biomedical Engineering, Tufts University, Medford, MA 02155, USA
| | - Jingjie Yeo
- Sibley School of Mechanical and Aerospace Engineering, Cornell University, Ithaca NY 14853, USA
| | - David L. Kaplan
- Department of Biomedical Engineering, Tufts University, Medford, MA 02155, USA
| |
Collapse
|
100
|
Sun YC, Boero G, Brugger J. Stretchable Conductors Fabricated by Stencil Lithography and Centrifugal Force-Assisted Patterning of Liquid Metal. ACS APPLIED ELECTRONIC MATERIALS 2021; 3:5423-5432. [PMID: 34977587 PMCID: PMC8717634 DOI: 10.1021/acsaelm.1c00884] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/20/2021] [Accepted: 11/16/2021] [Indexed: 05/26/2023]
Abstract
Embedding liquid metals (LMs) into an elastomer is emerging as a promising strategy for stretchable conductors. Existing manufacturing techniques are struggling between spatial resolution and process complexity and are limited to chemically resistant substrates. Here, we report on a hybrid process combining stencil lithography and centrifugal force-assisted patterning of liquid metal for the development of LM-based stretchable conductors. The selective wetting behavior of oxide-removed eutectic gallium-indium (EGaIn) on metal patterns defined by stencil lithography enables micrometer scale LM patterns on an elastomeric substrate. Stencil lithography allows for defining metal regions without harsh chemical treatments, making it suitable for a wide range of substrates. Microscale LM patterns are achieved by efficiently removing the excess material by the centrifugal forces experienced from spinning the substrate. The proposed approach allows for the creation of LM patterns with a line width as small as 2 μm on a stretchable poly(dimethylsiloxane) (PDMS) substrate. The electrical measurement results show that the fabricated EGaIn devices can endure 40% mechanical strain over several thousands of cycles. Furthermore, a stencil design using microbridges is proposed to address the mechanical stability issue in stencil lithography. An EGaIn conductor with a serpentine structure and an interdigitated capacitor are fabricated and characterized. The results demonstrate that the patterned serpentine conductors retain their functionality with applied mechanical strain up to 80%. The performance of the interdigitated capacitors upon applied strain is in good agreement with the theoretical estimation. Finally, we demonstrate our approach also on poly(octamethylene maleate (anhydride) citrate) (POMaC) substrates to broaden the use of the proposed method to not only flexible and stretchable but also biodegradable substrates, opening a way for in vivo transient microsystem engineering. The work presented here provides a versatile and reliable approach for manufacturing stretchable conductors.
Collapse
|