Biodegradation of bioplastics in natural environments

Mesocosm trials reveal the potential toxic risk of degrading bioplastics to marine life

If biodegradable plastics tackle the marine plastic pollution problem sufficiently remains questionable. To gain more insight in degradability, performance, and the impact of degradation on the toxicity, commercial bags made from two biodegradable plastics and one conventional plastic (PE) were exposed for 120 days in a mesocosm featuring benthic, pelagic, and littoral habitat simulations. Degradability was assessed as weight loss, and specimens were tested for toxicity using Paracentrotus lividus sea-urchin larvae after different exposure times. Both biodegradable bags showed degradation within 120 days, with the littoral simulation showing the highest and the pelagic simulation the lowest decay. Disregarding habitat, the home-compostable plastic showed higher marine degradation than the industrial-compostable material. The relevant initial toxicity of both biopolymers was lost within 7 days of exposure, pointing towards easily leachable chemical additives as its cause. Interestingly, littoral exposed specimens gained toxicity after 120 days, suggesting UV- induced modifications that increase biopolymer toxicity.

Impact of mechanical and thermo-chemical pretreatments to enhance anaerobic digestion of poly(lactic acid)

To date, the introduction of biodegradable plastics such as PLA in anaerobic digestion systems has been limited by a very low rate of biodegradation. To overcome these limitations, pretreatment technologies can be applied. In this study, the impact of pretreatments (mechanical, thermal, thermo-acid, and thermo-alkaline) was investigated. Mechanical pretreatment of PLA improved its biodegradation rate but did not affect the ultimate methane potential (430-461 NL CH₄ kg^-1 VS). In parallel, thermal and thermo-acid pretreatments exhibited a similar trend for PLA solubilization. Both of these pretreatments only achieved substantial solubilization (>60%) at higher temperatures (120 and 150 °C). At lower temperatures (70 and 90 °C), negligible solubilization (between 1 and 6%) occurred after 48 h. By contrast, coupling of thermal and alkaline pretreatment significantly increased solubilization at the lower temperatures (70 and 90 °C). In terms of biodegradation, thermo-alkaline pretreatment (with 5% w/v Ca(OH)₂) of PLA resulted in a similar methane potential (from 325 to 390 NL CH₄ kg^-1 VS) for 1 h at 150 °C, 6 h at 120 °C, 24 h at 90 °C, and 48 h at 70 °C. Reduction of the Ca(OH)₂ concentration (from 5% to 0.5% w/v) highlighted that a concentration of 2.5% w/v was sufficient to achieve a substantial level of biodegradation. Pretreatment at 70 and 90 °C using 2.5% w/v Ca(OH)₂ for 48 h resulted in biodegradation yields of 73% and 68%, respectively. Finally, a good correlation (R² = 0.90) was found between the PLA solubilization and its biodegradation.

Assessing the anaerobic degradability and the potential recovery of biomethane from different biodegradable bioplastics in a full-scale approach

The aim of the present study was to evaluate the anaerobic degradability and the potential recovery of biomethane from different bioplastics using a full-scale approach. Bioplastics were placed inside a real anaerobic digestion plant working under thermophilic conditions and quantitative and qualitative degradation of bioplastics was evaluated. Laboratory-scale experiments were used to determine the amount of biomethane produced by anaerobic degradation of bioplastics. Polylactic acid-based items may degrade completely using retention times compatible with anaerobic digestion plants contributing positively to biomethane production, i.e., in 90 days 397 ± 8 NL CH₄ kg_{volatile solids}^-1 were produced by polylactic acid-based cutlery. Starch-based shoppers showed a quick degradation of the starch component in the first month of anaerobic digestion, followed by a slow degradation of the polyester component. Anaerobic digestion and/or anaerobic digestion coupled to digestate composting may represent the best strategy to dispose these wastes meeting the principles of Circular Economy.

Transparent, UV-blocking, and high barrier cellulose-based bioplastics with naringin as active food packaging materials

Free-standing, robust, and transparent bioplastics were obtained by blending cellulose and naringin at different proportions. Optical, thermal, mechanical, antioxidant, and antimicrobial properties were systematically investigated. In general, the incorporation of naringin produced important UV blocking and plasticizer effects and good antioxidant and antibacterial properties. Moreover, the barrier properties were characterized by determination of their water and oxygen transmission rates, finding that both parameters decreased by increasing the naringin content and reaching values similar to other petroleum-based plastics and cellulose derivatives used for food packaging applications. Finally, the biodegradability of these films was determined by measurement of the biological oxygen demand (BOD) in seawater, demonstrating an excellent decomposition in such conditions.

Closing the Carbon Loop in the Circular Plastics Economy

Today, plastics are ubiquitous in everyday life, problem solvers of modern technologies, and crucial for sustainable development. Yet the surge in global demand for plastics of the growing world population has triggered a tidal wave of plastic debris in the environment. Moving from a linear to a zero-waste and carbon-neutral circular plastic economy is vital for the future of the planet. Taming the plastic waste flood requires closing the carbon loop through plastic reuse, mechanical and molecular recycling, carbon capture, and use of the greenhouse gas carbon dioxide. In the quest for eco-friendly products, plastics do not need to be reinvented but tuned for reuse and recycling. Their full potential must be exploited regarding energy, resource, and eco efficiency, waste prevention, circular economy, climate change mitigation, and lowering environmental pollution. Biodegradation holds promise for composting and bio-feedstock recovery, but it is neither the Holy Grail of circular plastics economy nor a panacea for plastic littering. As an alternative to mechanical downcycling, molecular recycling enables both closed-loop recovery of virgin plastics and open-loop valorization, producing hydrogen, fuels, refinery feeds, lubricants, chemicals, and carbonaceous materials. Closing the carbon loop does not create a Perpetuum Mobile and requires renewable energy to achieve sustainability. This article is protected by copyright. All rights reserved.

Effect of propiconazole on plastic film microplastic degradation: Focusing on the change in microplastic morphology and heavy metal distribution

With the rapid increase in the use of plastic films, microplastic (MP) pollution in agricultural soils has become a global environmental problem. Propiconazole is widely used in agriculture and horticulture; however, its role in plastic film degradation remains elusive. Butylene adipate-co-terephthalate (PBAT) and polyethylene (PE) films were used to analyze the effects of propiconazole on plastic film and MP degradation. We identified the surface morphologies of PBAT and PE at different propiconazole concentrations and soil pH values, as well as the adsorption and release characteristics of heavy metals during the degradation process via scanning electron microscopy, Fourier transform infrared spectroscopy and inductively coupled plasma mass spectrometry. Propiconazole accelerated the degradation of MPs, adsorption of heavy metals (Ni and Zn), and release of Sn at low concentrations (≤40 mg/kg); however, these effects were evidently absent at a high concentration (120 mg/kg). Furthermore, MPs were more prone to degradation in acidic or alkaline soils than in neutral soil when they coexisted with propiconazole. Hence, we suggest that PBAT and PE plastic films may not be suitable for application in acidic and alkaline soils with propiconazole, because of shorter rupture time and more heavy metal adsorption. PBAT degraded faster, absorbed and released more heavy metals than PE. Under all tested conditions, the heavy metal contents in MPs gradually approached those in soil, which proves that MPs are carriers of heavy metal pollutants. These results may help in assessing the impact of MPs on soil environments and provide a theoretical basis for the standardized propiconazole and plastic film usage.

Recycled (Bio)Plastics and (Bio)Plastic Composites: A Trade Opportunity in a Green Future

Today’s world is at the point where almost everyone realizes the usefulness of going green. Due to so-called global warming, there is an urgent need to find solutions to help the Earth and move towards a green future. Many worldwide events are focusing on the global technologies in plastics, bioplastic production, the recycling industry, and waste management where the goal is to turn plastic waste into a trade opportunity among the industrialists and manufacturers. The present work aims to review the recycling process via analyzing the recycling of thermoplastic, thermoset polymers, biopolymers, and their complex composite systems, such as fiber-reinforced polymers and nanocomposites. Moreover, it will be highlighted how the frame of the waste management, increasing the materials specificity, cleanliness, and a low level of collected material contamination will increase the potential recycling of plastics and bioplastics-based materials. At the same time, to have a real and approachable trade opportunity in recycling, it needs to implement an integrated single market for secondary raw materials.

The role of (bio)degradability on the management of petrochemical and bio-based plastic waste

In order to mitigate the social and ecological impacts of post-consumer plastic made of conventional petrochemical polymers, the market of (bio)degradable plastics have recently become more widespread. Although (bio)degradable plastics could be an environmentally friendly substitute of petrochemical ones, the consequences of their presence in the waste management system and in the environment (if not correctly disposed) are not always positive and plastic pollution is not automatically solved. Consequently, this work aims to review how plastic (bio)degradability affects the municipal solid waste management cycle. To this end, the state-of-the-art of the intrinsic (bio)degradability of conventional and unconventional petrochemical and bio-based polymers has been discussed, focusing on the environment related to the waste management system. Then, the focus was on strategies to improve polymer (bio)degradability: different types of eco-design and pre-treatment approach for plastics has been investigated, differently from other works that focused only on specific topics. The information gathered was used to discuss three typical disposal/treatment routes for plastic waste. Despite many of the proposed materials in eco-design have increased the plastics (bio)degradability and pre-treatments have showed interesting results, these achievements are not always positive in the current MSW management system. The effect on mechanical recycling is negative in several cases but the enhanced (bio)degradability can help the treatment with organic waste. On the other hand, the current waste treatment facility is not capable to manage this waste, leading to the incineration the most promising options. In this way, the consumption of raw materials will persist even by using (bio)degradable plastics, which strength the doubt if the solution of plastic pollution leads really on these materials. The review also highlighted the need for further research on this topic that is currently limited by the still scarce amount of (bio)degradable plastics in input to full-scale waste treatment plants.

Preparation of bioplastic consisting of salmon milt DNA

The microplastic that pollutes the ocean is a serious problem around the world. The bioplastic consisting of biopolymers which is degraded in nature, is one of the strategies to solve this problem. Although the bioplastics consisting of protein, polysaccharide, polylactic acid, etc., have been reported, which consist of DNA, one of the most important materials in the genetic process, have not been reported to the best of our knowledge. In addition, a large amount of DNA-containing materials, such as salmon milts, is discarded as industrial waste around the world. Therefore, we demonstrated the preparation of a bioplastic consisting of salmon milt DNA. The DNA plastic was prepared by the immersion of a DNA pellet in a formaldehyde (HCHO) solution and heating. As a result, the water-stable DNA plastics were obtained at the HCHO concentration of 20% or more. Particularly, the DNA plastic with a 25% HCHO treatment showed water-insoluble, thermally stable, and highly mechanical properties. These are due to the formation of a three-dimensional network via the crosslinking reaction between the DNA chains. In addition, since DNA in plastic possesses the double-stranded structure, these plastics effectively accumulated the DNA intercalator, such as ethidium bromide. Furthermore, the DNA plastics indicated a biodegradable property in a nuclease-containing aqueous solution and the biodegradable stability was able to be controlled by the HCHO concentration. Therefore, salmon milt DNA has shown the potential to be a biodegradable plastic.

Occurrence, impact, toxicity, and degradation methods of microplastics in environment-a review

Microplastic defines as a tiny plastic particle that has a size of less than 5 mm and is ubiquitous in the environment. Due to the tiny size, this microplastic adversely affected the environment, notably aquatic life via ingestion, choking, and entanglement. This microplastic is arduous to degrade as it takes a thousand years due to the properties of plastic itself and consequently remains in nature. In dealing with microplastic issues, this paper reflects the occurrence, impact, toxicity, and degradation methods of microplastics in the environment including physical, chemical, and biological treatments. Here, the physical treatment methods include incineration treatment, ultraviolet (UV), and photocatalytic. The incineration process contributes to environmental pollution due to the release of toxic gases into the atmosphere. In addition, chemical treatments for plastic waste are the degradation process involving chemical additives such as ethylene glycol (EG), nano-magnesium oxide (MgO), diethylene glycol (DEG), and calcium or zinc (Ca/Zn) stearate as a catalyst. These treatments depend on the chemicals that can affect human health and the ecosystem. The biodegradation treatment using bacterial and fungal species can consume the microplastic without disrupting the surrounding environment and biota. It includes recent findings on the biodegradation of microplastic under aerobic and anaerobic conditions. Thus, biodegradation can be considered the best option to degrade microplastic as green and sustainable technology.

A review on the occurrence and influence of biodegradable microplastics in soil ecosystems: Are biodegradable plastics substitute or threat?

Plastic products are widely used around the world, but waste plastic is not reasonably managed and causes serious plastic pollution. Biodegradable plastics (BPs) provide an alternative to conventional plastics, but not all BPs can be completely degraded under natural conditions. Instead, they may break down into microplastics (MPs) faster than conventional plastics, posing an additional threat to soil environment. In this paper, the definition, applications, and degradation behaviors of BPs, including biodegradable microplastics (BMPs), are reviewed, and we comprehensively summarized the eco-toxicological effects of BMPs in soil ecosystems, in terms of physical and chemical properties of soil, soil nutrient cycling, soil bacterial and fungal communities, soil flora and fauna. The compound effects of BMPs and other pollutants were also addressed. The results revealed that BMPs made different or more severely effects compared to conventional MPs. Overall, this review aims to address gaps in knowledge, shed light on the ecological effects of BPs and BMPs in soil. BPs are not a perfect substitute to solve plastic pollution, and further exploration should focus on their generation, environmental behavior, ecological impact and whether BMPs cause more harm than conventional MPs.

Anaerobic digestion and aerobic composting of rigid biopolymers in bio-waste treatment: fate and effects on the final compost

Bioplastics may be collected in the bio-waste treatment, which is often composed of anaerobic digestion and subsequent aerobic composting of the digestates. The aim of this study was to evaluate the degradability of polylactic acid (PLA) and starch-based bioplastics (SBB) spoons under industrial conditions. Biomethane potential (BMP) was measured and biogas production was monitored, while the quality of composts was assessed by phytotoxicity and ecotoxicity tests. The bioplastics disintegration resulted in 65.1 ± 4.6 % for PLA and ≤ 65.0 ± 7.4 % for SBB, not achieving the target set by UNI EN 13,432 standard, and several residues were found in compost. Phytotoxicity tests on seeds reported the lowest Germination Index for PLA elutriate, whereas a potential negative effect of SBB on soil fauna was detected. Further investigation is needed to assess the fate of these ever-growing materials under industrial conditions, and also evaluate the effects of residues in compost.

Production and waste treatment of polyesters: application of bioresources and biotechniques

Chemical resources and techniques have long been used in the history of bulk polyester production and still dominate today's chemical industry. The sustainable development of the polyester industry demands more renewable resources and environmentally benign polyester products. Accordingly, the rapid development of biotechnology has enabled the production of an extensive range of aliphatic and aromatic polyesters from renewable bio-feedstocks. This review addresses the production of representative commercial polyesters (polyhydroxyalkanoates, polylactic acid, poly ε-caprolactone, polybutylene succinate, polyethylene terephthalate, polybutylene terephthalate, polypropylene terephthalate, polyethylene furandicarboxylate, polypropylene furandicarboxylate, and polybutylene furandicarboxylate) or their monomers (lactic acid, succinic acid, 1,4-butanediol, ethylene glycol, terephthalic acid, 1,3-propanediol, and 2,5-furandicarboxylic acid) from renewable bioresources. In addition, this review summarizes advanced biotechniques in the treatment of polyester wastes, representing the near-term trends and future opportunities for waste-to-value recycling and the remediation of polyester wastes under sustainable models. For future prospects, it is essential to further expand: non-food bioresources, optimize bioprocesses and biotechniques in the preparation of bioderived or biodegradable polyesters with promising: material performance, biodegradability, and low production cost.

UV degradation of poly(lactic acid) materials through copolymerisation with a sugar-derived cyclic xanthate

The copolymerisation of L-Lactide with a cyclic xanthate monomer derived from tri-O-acetyl-D-glucal has been used to incorporate thionocarbonate and thioester linkages into a polyester backbone. The poly(lactide-co-xanthate) copolymers show enhanced UV-degradability compared to PLA, with 40% mass loss within 6 hours of UV exposure (365 nm) for only 3% of sulfur-containing linkages.

Rogue one: A plastic story

Plastic comprises of variety of polymers and has many applications, but the waste generated by plastic pose threat to environment and marine life. Plastic can be classified into two types: thermoplastics and thermosetting and are divided into 7 different categories: (Polyethylene Terephthalate [PETE], High-Density Polyethylene [HDPE], Polyvinyl Chloride [PVC], Low-Density Polyethylene [LDPE], Polypropylene [PP], Polystyrene or Styrofoam [PS] & Polycarbonate or ABS [others]). To curb the deleterious effects of plastic waste various methods have been devised and utilized that include chemical, physical and biological treatments. One of the aspects primarily focused by the researchers is the phenomenon of biodegradation and there are many microorganisms (bacteria) that have the ability to carry out this particular process. These bacteria assist biodegradation by production of several enzymes like PETases and MHETases. There are few microorganisms that have been listed which cannot be applied for industrial use due to its low biodegradation capacity. To overcome this problem, PHA is one of the alternatives to replace the synthetic plastic due to its high degrading capacity.

Methodologies to Assess the Biodegradability of Bio-Based Polymers—Current Knowledge and Existing Gaps

Our society lives in a time of transition where traditional petroleum-based polymers/plastics are being replaced by more sustainable alternative materials. To consider these bioproducts as more viable options than the actual ones, it is demanded to ensure that they are fully biodegradable or compostable and that there is no release of hazardous compounds to the environment with their degradation. It is then essential to adapt the legislation to support novel specific guidelines to test the biodegradability of each biopolymer in varied environments, and consequently, establish consistent data to design a coherent labeling system. This review work aims to point out the current standards that can serve as a basis for the characterization of biopolymers’ biodegradation profile in different environments (soil, compost, and aquatic systems) and identify other laboratory methodologies that have been adopted for the same purpose. With the information gathered in this work, it was possible to identify remaining gaps in existing national and international standards to help establish new validation criteria to be introduced in future research and policies related to bioplastics to boost the sustainable progress of this rising industry.

A Comprehensive Review of the Development of Carbohydrate Macromolecules and Copper Oxide Nanocomposite Films in Food Nanopackaging

Background. Food nanopackaging helps maintain food quality against physical, chemical, and storage instability factors. Copper oxide nanoparticles (CuONPs) can improve biopolymers’ mechanical features and barrier properties. This will lead to antimicrobial and antioxidant activities in food packaging to extend the shelf life. Scope and Approach. Edible coatings based on carbohydrate biopolymers have improved the quality of packaging. Several studies have addressed the role of carbohydrate biopolymers and incorporated nanoparticles to enhance food packets’ quality as active nanopackaging. Combined with nanoparticles, these biopolymers create film coatings with an excellent barrier property against transmissions of gases such as O2 and CO2. Key Findings and Conclusions. This review describes the CuO-biopolymer composites, including chitosan, agar, cellulose, carboxymethylcellulose, cellulose nanowhiskers, carrageenan, alginate, starch, and polylactic acid, as food packaging films. Here, we reviewed different fabrication techniques of CuO biocomposites and the impact of CuONPs on the physical, mechanical, barrier, thermal stability, antioxidant, and antimicrobial properties of carbohydrate-based films.

Manufacturing of Biocomposites for Domestic Applications Using Bio-Based Filler Materials

Filler materials are considered added value (volume) to composite materials. The addition of filler materials leads to altering the material characteristics. Nowadays, there has been a notable increase in bio-based materials in polymers and polymer composites. In this regard, agricultural wastes (low-cost renewable substrates) are used as filler content to prepare bioplastic composites, as they are available plenty in quantity and economical in price. Bioplastics composite samples are compounded by adding different amounts of eggshell powder and walnut shell powder in weight proportion to the plasticized PLA. The plasticization is realized with 5 wt.% of Epoxidized Soybean Oil. The prepared bioplastic granules are further processed by injection molding to dog bone-shaped samples subjected to different mechanical, thermal, and optical microscopy tests. Mechanical tests such as Tensile, Charpy Impact, and Flexural tests yielded decreased properties compared to virgin PLA. However, the properties of plasticized PLA–ES composite showed better results than plasticized PLA–WS composite.

Microbial communities on biodegradable plastics under different fertilization practices in farmland soil microcosms

Plastic mulching is a common practice in agricultural systems and is often combined with fertilization. Biodegradable plastics (BPs) are becoming an alternative to non-biodegradable plastics (non-BPs) for soil mulching. However, the effects of fertilization on the microbial communities on BPs remain unclear. Here, we explored the responses of the plastisphere to different fertilization practices in soil-based microcosms containing three BPs: polylactic acid (PLA), poly (butylene succinate) (PBS), and poly (butylene-adipate-co-terephthalate) (PBAT), and one non-BP (low-density polyethylene, LDPE). The 16S and ITS rRNA gene-based Illumina sequencing method were used to identify the bacterial and fungal communities on the plastics and in the soils. Microbial community structure on BPs was significantly different from that in soils and on LDPE. The predicted functional profiles of bacteria on BPs, especially PBAT, were distinct from those in soils. The plastisphere communities on BPs were dominated by microbes adapted to access and utilize carbon sources compared with of the communities on LDPE. Application of manure increased the alpha diversity of bacterial communities on BPs but decreased it on LDPE. The structure of bacterial communities on BPs changed with the application of manure. Our research establishes the baseline dynamics of plastisphere communities on BPs in soils.

A Brief Review of Poly (Butylene Succinate) (PBS) and Its Main Copolymers: Synthesis, Blends, Composites, Biodegradability, and Applications

PBS, an acronym for poly (butylene succinate), is an aliphatic polyester that is attracting increasing attention due to the possibility of bio-based production, as well as its balanced properties, enhanced processability, and excellent biodegradability. This brief review has the aim to provide the status concerning the synthesis, production, thermal, morphological and mechanical properties underlying biodegradation ability, and major applications of PBS and its principal copolymers.

Microplastics change soil properties, heavy metal availability and bacterial community in a Pb-Zn-contaminated soil

Microplastics (MPs) co-occur widely with diverse contaminants in soils. However, few data are available on their impacts on soil chemical and microbial properties of heavy metal-contaminated soils. For the first time, we investigated the changes in chemical and microbial properties of a Pb-Zn-contaminated soil as induced by six different MPs, including polyethylene (PE), polystyrene (PS), polyamide (PA), polylactic acid (PLA), polybutylene succinate (PBS), and polyhydroxybutyrate (PHB), at two doses (0.2% and 2%, w/w). After 120 days of soil incubation, significant changes were observed in soil pH, dissolved organic carbon (DOC), NH₄⁺-N, NO₃^--N, available P, the availability of Zn and Pb, and the activities of soil enzymes. Overall, MPs especially at the dose of 2% decreased the richness and diversity of bacterial communities and altered microbial community composition, causing special enrichments of specific taxa. MPs increased predicted functional genes involved in xenobiotics biodegradation and metabolism. Generally, impacts were dependent on MPs' type and dose. Changes in soil properties and heavy metal availability had significant correlations with bacterial community diversity and composition. Our findings imply that MPs co-occurring with heavy metals may change metal mobility, soil fertility, and microbial diversity and functions, thus causing a potential threat to soil ecosystem multifunctionality.

A Critical Review of the Performance and Soil Biodegradability Profiles of Biobased Natural and Chemically Synthesized Polymers in Industrial Applications

This review explores biobased polymers for industrial applications, their end fate, and most importantly, origin and key aspects enabling soil biodegradation. The physicochemical properties of biobased synthetic and natural polymers and the primary factors governing degradation are explored. Current and future biobased systems and factors allowing for equivalent comparisons of degradation and possible sources for engineering improved biodegradation are reviewed. Factors impacting ultraviolet (UV) stability of biopolymers have been described including methods to enhance photoresistance and impact on biodegradation. It discusses end-fate of biopolymers in soil and impact of residues on soil health. A limited number of studies examine side effects (e.g., microbial toxicity) from soil biodegradation of composites and biopolymers. Currently available standards for biodegradation and composting have been described with limitations and scope for improvements. Finally, design considerations and implications for sustainable polymers used, under consideration, and to be considered within the context of a rational biodegradable strategy are elaborated.

Identification of novel extracellular putative chitinase and hydrolase from Geomyces sp. B10I with the biodegradation activity towards polyesters

Cold-adapted filamentous fungal strain Geomyces sp. B10I has been reported to decompose polyesters such as poly(e-caprolactone) (PCL), poly(butylene succinate) (PBS) and poly(butylene succinate-co-butylene adipate) (PBSA). Here, we identified the enzymes of Geomyces sp. B10I, which appear to be responsible for its biodegradation activity. We compared their amino acid sequences with sequences of well-studied fungal enzymes. Partial purification of an extracellular mixture of the two enzymes, named hydrGB10I and chitGB10I, using ammonium sulfate precipitation and ionic exchange chromatography gave 14.16-fold purity. The amino acid sequence of the proteins obtained from the MALDI-TOF analysis determined the molecular mass of 77.2 kDa and 46.5 kDa, respectively. Conserved domain homology analysis revealed that both proteins belong to the class of hydrolases; hydrGB10I belongs to the glycosyl hydrolase 81 superfamily, while chitGB10I contains the domain of the glycosyl hydrolase 18 superfamily. Phylogenetic analysis suggests a distinct nature of the hydrGB10I and chitGB10I of Geomyces sp. B10I when compared with other fungal polyester-degrading enzymes described to date.

Can anaerobic digestion be a suitable end-of-life scenario for biodegradable plastics? A critical review of the current situation, hurdles, and challenges

Growing concern regarding non-biodegradable plastics and the impact of these materials on the environment has promoted interest in biodegradable plastics. The intensification of separate biowastes collection in most European countries has also contributed to the development of biodegradable plastics, and the subject of their end-of-life is becoming a key issue. To date, there has been relatively little research to evaluate the biodegradability of biodegradable plastics by anaerobic digestion (AD) compared to industrial and home composting. However, anaerobic digestion is a particularly promising strategy for treating biodegradable organic wastes in the context of circular waste management. This critical review aims to provide an in-depth update of anaerobic digestion of biodegradable plastics by providing a summary of the literature regarding process performances, parameters affecting biodegradability, the microorganisms involved, and some of the strategies (e.g., pretreatment, additives, and inoculum acclimation) used to enhance the degradation rate of biodegradable plastics. In addition, a critical section is dedicated to suggestions and recommendations for the development of biodegradable plastics sector and their treatment in anaerobic digestion.

Oil Production by Pyrolysis of Real Plastic Waste

The aim of this paper is for the production of oils processed in refineries to come from the pyrolysis of real waste from the high plastic content rejected by the recycling industry of the Basque Country (Spain). Concretely, the rejected waste streams were collected from (1) a light packaging waste sorting plant, (2) the paper recycling industry, and (3) a waste treatment plant of electrical and electronic equipment (WEEE). The influence of pre-treatments (mechanical separation operations) and temperature on the yield and quality of the liquid fraction were evaluated. In order to study the pre-treatment effect, the samples were pyrolyzed at 460 °C for 1 h. As pre-treatments concentrate on the suitable fraction for pyrolysis and reduce the undesirable materials (metals, PVC, PET, inorganics, cellulosic materials), they improve the yield to liquid products and considerably reduce the halogen content. The sample with the highest polyolefin content achieved the highest liquid yield (70.6 wt.% at 460 °C) and the lowest chlorine content (160 ppm) among the investigated samples and, therefore, was the most suitable liquid to use as refinery feedstock. The effect of temperature on the pyrolysis of this sample was studied in the range of 430–490 °C. As the temperature increased the liquid yield increased and solid yield decreased, indicating that the conversion was maximized. At 490 °C, the pyrolysis oil with the highest calorific value (44.3 MJ kg⁻¹) and paraffinic content (65% area), the lowest chlorine content (128 ppm) and more than 50 wt.% of diesel was obtained.

Novel Polyhydroxybutyrate-Degrading Activity of the Microbulbifer Genus as Confirmed by Microbulbifer sp. SOL03 from the Marine Environment

Ever since bioplastics were globally introduced to a wide range of industries, the disposal of used products made with bioplastics has become an issue inseparable from their application. Unlike petroleum-based plastics, bioplastics can be completely decomposed into water and carbon dioxide by microorganisms in a relatively short time, which is an advantage. However, there is little information on the specific degraders and accelerating factors for biodegradation. To elucidate a new strain for biodegrading poly-3-hydroxybutyrate (PHB), we screened out one PHB-degrading bacterium, Microbulbifer sp. SOL03, which is the first reported strain from the Microbulbifer genus to show PHB degradation activity, although Microbulbifer species are known to be complex carbohydrate degraders found in high-salt environments. In this study, we evaluated its biodegradability using solid- and liquid-based methods in addition to examining the changes in physical properties throughout the biodegradation process. Furthermore, we established the optimal conditions for biodegradation with respect to temperature, salt concentration, and additional carbon and nitrogen sources; accordingly, a temperature of 37°C with the addition of 3% NaCl without additional carbon sources, was determined to be optimal. In summary, we found that Microbulbifer sp. SOL03 showed a PHB degradation yield of almost 97% after 10 days. To the best of our knowledge, this is the first study to investigate the potent bioplastic degradation activity of Microbulbifer sp., and we believe that it can contribute to the development of bioplastics from application to disposal.

Utilization of Polyurethane Foam Dust in Development of Thermal Insulation Composite

The massive production of Polyurethane foam from various products generates an extensive amount of waste, mostly in the form of dust that is emitted while cutting, trimming, or grinding the foam. In this research, the polyurethane dust (PUD) waste is incorporated into unsaturated polyester resin (UPR) to fabricate a heat insulation composite material to be used in construction. Filler percentages ranging from 10% to 50% were used to make the UPR-PUD composite materials. The thermal and mechanical properties of the material were studied in order to evaluate the ability of the composites for this type of application. Thermogravimetric Analysis and Differential Scanning Calorimeter tests were applied to determine the thermal stability of the material. In addition, the microstructure of the prepared composites and the incorporation of PUD filler into the polyester matrix were investigated by Scanning Electron Microscopy, X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR) analysis. The FTIR and XRD analyses suggested that adding PUD improved the curing process of unsaturated polyester and enhanced its crystalline structure. The experimental results showed promising thermal insulation capability, with low thermal conductivity in the range of 0.076 to 0.10 and low water retention. Moreover, the composites exhibited compression strength between 56 and 100 MPa and tensile strength between 10.3 and 28 MPa, much higher than traditional thermal insulators and many building materials.

Sustainability of Synthetic Plastics: Considerations in Materials Life-Cycle Management

The sustainability of current and future plastic materials is a major focus of basic research, industry, government, and society at large. There is a general recognition of the positive impacts of plastics, especially packaging; however, the negative consequences around end-of-life outcomes and overall materials circularity are issues that must be addressed. In this perspective, we highlight some of the challenges associated with the many uses of plastic components and the diversity of materials needed to satisfy consumer demand, with several examples focused on plastics packaging. We also discuss the opportunities provided by conventional and advanced recycling/upgrading routes to petrochemical and bio-based materials and feedstocks, along with overviews of chemistry-related (experimental, computational, data science, and materials traceability) approaches to the valorization of polymers toward a closed-loop environment.

Biodegradable and high-performance multiscale structured nanofiber membrane as mask filter media via poly(lactic acid) electrospinning

The usage of single-use face masks (SFMs) has increased since the outbreak of the coronavirus pandemic. However, non-degradability and mismanagement of SFMs have raised serious environmental concerns. Moreover, both melt-blown and nanofiber-based mask filters inevitably suffer from poor filtration performance, like a continuous decrease in the removal efficiency for particulate matter (PM) and weak breathability. Herein, we report a new method to create biodegradable and reusable fibrous mask filters. The filter consists of a true nanoscale bio-based poly(lactic acid) (PLA) fiber (an average size of 37 ± 4 nm) that is fabricated via electrospinning of an extremely dilute solution. Furthermore, we designed a multiscale structure with integrated features, such as low basis weight (0.91 g m⁻²), small pore size (0.73 μm), and high porosity (91.72%), formed by electrospinning deposition of true nanoscale fibers on large pore of 3D scaffold nanofiber membranes. The resultant mask filter exhibited a high filtration efficiency (PM_0.3–99.996%) and low pressure drop (104 Pa) superior to the commercial N95 filter. Importantly, this filter has a durable filtering efficiency for PM and natural biodegradability based on PLA. Therefore, this study offers an innovative strategy for the preparation of PLA nanofibers and provides a new design for high-performance nanofiber filters.

Natural Fiber-Reinforced Polycaprolactone Green and Hybrid Biocomposites for Various Advanced Applications

Recent developments within the topic of biomaterials has taken hold of researchers due to the mounting concern of current environmental pollution as well as scarcity resources. Amongst all compatible biomaterials, polycaprolactone (PCL) is deemed to be a great potential biomaterial, especially to the tissue engineering sector, due to its advantages, including its biocompatibility and low bioactivity exhibition. The commercialization of PCL is deemed as infant technology despite of all its advantages. This contributed to the disadvantages of PCL, including expensive, toxic, and complex. Therefore, the shift towards the utilization of PCL as an alternative biomaterial in the development of biocomposites has been exponentially increased in recent years. PCL-based biocomposites are unique and versatile technology equipped with several importance features. In addition, the understanding on the properties of PCL and its blend is vital as it is influenced by the application of biocomposites. The superior characteristics of PCL-based green and hybrid biocomposites has expanded their applications, such as in the biomedical field, as well as in tissue engineering and medical implants. Thus, this review is aimed to critically discuss the characteristics of PCL-based biocomposites, which cover each mechanical and thermal properties and their importance towards several applications. The emergence of nanomaterials as reinforcement agent in PCL-based biocomposites was also a tackled issue within this review. On the whole, recent developments of PCL as a potential biomaterial in recent applications is reviewed.

Integrated polylactic acid and biodiesel production from food waste: Process synthesis and economics

In this study, techno-economic analysis of the sustainable production of polylactic acid (PLA) and biodiesel from Food Waste (FW), with a plant capacity of 50 tons/day, was investigated. In addition, FW of four countries (China, India, Brazil, and the USA) with different compositions of water, protein, lipid and carbohydrate were proposed. Each country has different PLA production rates based on carbohydrate and biodiesel production based on fat. In this study, the FW composition of the USA shows better economic feasibility than other countries. The actual minimum selling price is 6.53 (China), 5.35 (India), 4.75 (Brazil), and 4.29 (US) $/kg. The uncertainty of the MSP was analyzed based on various input limits. The sensitivity analysis was conducted based on biodiesel-selling price, PLA-selling price, income tax, and project lifetime on techno-economic analysis parameters, such as ROI, payback period, IRR and NPV were investigated.

Biodegradation of microplastics: Better late than never

Plastics use is growing due to its applications in the economy, human health and aesthetics. The major plastic particles in the form of microplastics (MPs) released into the environment are made up of polyethylene (PE), polypropylene (PP), polyvinylchloride (PVC), and polyethylene terephthalate (PET). Tremendous usage and continuous accumulation of MPs in the environment pose a global threat to ecosystems and human health. The current knowledge of biotechnological, aerobic and aerobic biodegradation approaches emphasizes the microbial culture's potential towards MPs removal. This review selectively provides recent biotechnological advances such as biostimulation, bioaugmentation and enzymatic biodegradation that can be applied for MPs removal by biodegradation and bioaccumulation. This review summarizes the knowledge and the research exploration on the biodegradation of synthetic organic MPs with different biodegradability. However, further research is still needed to understand the underlying mechanism of MPs biodegradation in soil and water systems, leading to the development of an effective method for MPs removal.

A review on marine plastisphere: biodiversity, formation, and role in degradation

The pollution of plastic waste has become an increasingly serious environmental crisis. Recently, plastic has been detected in various kinds of environments, even in human tissues, which is an increasing threat to the ecosystems and humans. In the ocean, the plastic waste is eventually fragmentized into microplastics (MPs) under the disruption of physical and chemical processes. MPs are colonized by microbial communities such as fungi, diatoms, and bacteria, which form biofilms on the surface of the plastic called “plastisphere”. In this review, we summarize the studies related to microorganisms in the plastisphere in recent years and describe the microbial species in the plastisphere, mainly including bacteria, fungi, and autotrophs. Secondly, we explore the interactions between MPs and the plastisphere. The depth of MPs in the ocean and the nutrients in the surrounding seawater can have a great impact on the community structure of microorganisms in the plastisphere. Finally, we discuss the types of MP-degrading bacteria in the ocean, and use the “seed bank” theory to speculate on the potential sources of MP-degrading microorganisms. Challenges and future research prospects are also discussed.

Production and assessment of the biodegradation and ecotoxicity of xylan- and starch-based bioplastics

Developing novel renewable (and preferably biodegradable) materials has become recurrent due to the growing concerns with environmental impacts of high volumes of plastic waste produced from oil-based sources over the past decades. This study aimed at developing bioplastics from a mixture of starch and xylan in variable ratios, and the combined effect of α-cellulose and holocellulose extracted from sugarcane bagasse added to the process. The disintegration of bioplastics was evaluated in both soil and composting. The ecotoxicity analyses with Saccharomyces cerevisiae, Bacillus subtilis and seeds of Cucumis sativus were conducted after disintegration. All formulations based on 5% (w/v) of total polysaccharides were dried at 30 °C and resulted in homogeneous and non-brittle bioplastics. The composting results showed that all bioplastic formulations disintegrated in 3 days, whereas the 25/75% (xylan/starch, w/w) formulation vanished in soil within 13 days. The ecotoxicity data showed no inhibition of microbial growth after biodegradation, yielding 100% of seed germination. Despite the positive influence of the bioplastic degradation on the root and hypocotyl growth, temporary inhibition of C. sativus tissues exposed to soil washing (10 days of disintegration) was observed. The study demonstrated that xylan/starch bioplastics result in non-ecotoxic biodegradable materials.

Strategies and progress in synthetic textile fiber biodegradability

Abstract

The serious issue of textile waste accumulation has raised attention on biodegradability as a possible route to support sustainable consumption of textile fibers. However, synthetic textile fibers that dominate the market, especially poly(ethylene terephthalate) (PET), resist biological degradation, creating environmental and waste management challenges. Because pure natural fibers, like cotton, both perform well for consumer textiles and generally meet certain standardized biodegradability criteria, inspiration from the mechanisms involved in natural biodegradability are leading to new discoveries and developments in biologically accelerated textile waste remediation for both natural and synthetic fibers. The objective of this review is to present a multidisciplinary perspective on the essential bio-chemo-physical requirements for textile materials to undergo biodegradation, taking into consideration the impact of environmental or waste management process conditions on biodegradability outcomes. Strategies and recent progress in enhancing synthetic textile fiber biodegradability are reviewed, with emphasis on performance and biodegradability behavior of poly(lactic acid) (PLA) as an alternative biobased, biodegradable apparel textile fiber, and on biological strategies for addressing PET waste, including industrial enzymatic hydrolysis to generate recyclable monomers. Notably, while pure PET fibers do not biodegrade within the timeline of any standardized conditions, recent developments with process intensification and engineered enzymes show that higher enzymatic recycling efficiency for PET polymer has been achieved compared to cellulosic materials. Furthermore, combined with alternative waste management practices, such as composting, anaerobic digestion and biocatalyzed industrial reprocessing, the development of synthetic/natural fiber blends and other strategies are creating opportunities for new biodegradable and recyclable textile fibers.

Article Highlights

The Use of Mussel Shell as a Bio-Additive for Poly(Lactic Acid) Based Green Composites

Mussel shell is one of the most hazardous aquaculture wastes and its powder was used as an additive for bio-degradable poly (lactic acid) in this current study. Bio-composites were fabricated via conventional melt mixing technique followed by an injection moulding process. The effects of mussel shell powder inclusion on mechanical, melt-flow, water uptake and morphological performance of poly (lactic acid)-based green composites were reported.

New approaches for the characterization of plastic-associated microbial communities and the discovery of plastic-degrading microorganisms and enzymes

Plastics in the environment represent new substrates for microbial colonization, and recent methodological advances allow for in-depth characterization of plastic-associated microbial communities (PAMCs). Over the past several decades, discovery of plastic degrading enzymes (PDEs) and plastic degrading microorganisms (PDMs) has been driven by efforts to understand microbially-mediated plastic degradation in the environment and to discover biocatalysts for plastic processing. In this review, we discuss the evolution of methodology in plastic microbiology and highlight major advancements in the field stemming from computational microbiology. Initial research relied largely on culture-based approaches like clear-zone assays to screen for PDMs and microscopy to characterize PAMCs. New computational tools and sequencing technologies are accelerating discoveries in the field through culture-independent and multi-omic approaches, rapidly generating targets for protein engineering and improving the potential for plastic-waste management.

Artificial Ageing, Chemical Resistance, and Biodegradation of Biocomposites from Poly(Butylene Succinate) and Wheat Bran

The results of comprehensive studies on accelerated (artificial) ageing and biodegradation of polymer biocomposites on PBS matrix filled with raw wheat bran (WB) are presented in this paper. These polymer biocomposites are intended for the manufacture of goods, in particular disposable packaging and disposable utensils, which decompose naturally under the influence of biological agents. The effects of wheat bran content within the range of 10–50 wt.% and extruder screw speed of 50–200 min⁻¹ during the production of biocomposite pellets on the resistance of the products to physical, chemical, and biological factors were evaluated. The research included the determination of the effect of artificial ageing on the changes of structural and thermal properties by infrared spectra (FTIR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TG). They showed structural changes—disruption of chains within the ester bond, which occurred in the composition with 50% bran content as early as after 250 h of accelerated ageing. An increase in the degree of crystallinity with ageing was also found to be as high as 48% in the composition with 10% bran content. The temperature taken at the beginning of weight loss of the compositions studied was also lowered, even by 30 °C at the highest bran content. The changes of mechanical properties of biocomposite samples were also investigated. These include: hardness, surface roughness, transverse shrinkage, weight loss, and optical properties: colour and gloss. The ageing hardness of the biocomposite increased by up to 12%, and the surface roughness (R_a) increased by as much as 2.4 µm at the highest bran content. It was also found that ageing causes significant colour changes of the biocomposition (ΔE = 7.8 already at 10% bran content), and that the ageing-induced weight loss of the biocomposition of 0.31–0.59% is lower than that of the samples produced from PBS alone (1.06%). On the other hand, the transverse shrinkage of moldings as a result of ageing turned out to be relatively small, at 0.05%–0.35%. The chemical resistance of biocomposites to NaOH and HCl as well as absorption of polar and non-polar liquids (oil and water) were also determined. Biodegradation studies were carried out under controlled conditions in compost and weight loss of the tested compositions was determined. The weight of samples made from PBS alone after 70 days of composting decreased only by 4.5%, while the biocomposition with 10% bran content decreased by 15.1%, and with 50% bran, by as much as 68.3%. The measurements carried out showed a significant influence of the content of the applied lignocellulosic fillers (LCF) in the form of raw wheat bran (WB) on the examined properties of the biocompositions and the course of their artificial ageing and biodegradation. Within the range under study, the screw speed of the extruder during the production of biocomposite pellets did not show any significant influence on most of the studied properties of the injection mouldings produced from it.

Isolation of Microbulbifer sp. SOL66 with High Polyhydroxyalkanoate-Degrading Activity from the Marine Environment

Having the advantage of eco-friendly decomposition, bioplastics could be used to replace petroleum-based plastics. In particular, poly(3-hydroxybutyrate) (PHB) is one of the most commercialized bioplastics, however, necessitating the introduction of PHB-degrading bacteria for its effective disposal. In this study, Microbulbifer sp. SOL66 (94.18% 16S rRNA with similarity to Microbulbifer hydrolyticus) demonstrated the highest degradation activity among five newly screened Microbulbifer genus strains. Microbulbifer sp. SOL66 showed a rapid degradation yield, reaching 98% in 4 days, as monitored by laboratory scale, gas chromatography-mass spectrometry, scanning electron microscopy, gel permeation chromatography, and Fourier transform infrared spectroscopy. The PHB film was completely degraded within 7 days at 37 °C in the presence of 3% NaCl. When 1% xylose and 0.4% ammonium sulfate were added, the degradation activity increased by 17% and 24%, respectively. In addition, this strain showed biodegradability on pellets of poly(3-hydroxybutyrate-co-4-hydroxybutyrate), as confirmed by weight loss and physical property changes. We confirmed that Microbulbifer sp. SOL66 has a great ability to degrade PHB, and has rarely been reported to date.

Advances in production of bioplastics by microalgae using food waste hydrolysate and wastewater: A review

Microalgae have emerged as an effective dual strategy for bio-valorisation of food processing wastewater and food waste hydrolysate which favours microalgae cultivation into producing value-added by products mainly lipids, carbohydrates, and proteins to the advantages of bioplastic production. Moreover, various microalgae have successfully removed high amount of organic pollutants from food processing wastewater prior discharging into the environment. Innovation of microalgae cultivating in food processing wastewater greatly reduced the cost of wastewater treatment compared to conventional approach in terms of lower carbon emissions, energy consumption, and chemical usage while producing microalgae biomass which can benefit low-cost fertilizer and bioplastic applications. The study on several microalgae species has all successfully grown on food waste hydrolysates showing high exponential growth rate and biomass production rich in proteins, lipids, carbohydrates, and fatty acids. Multiple techniques have been implemented for the extraction of food wastes to be incorporate into the bioplastic production.