Interface Engineering for Garnet-Based Solid-State Lithium-Metal Batteries: Materials, Structures, and Characterization

Solid Polymer Electrolytes with Sacrificial End Groups for a Wide Oxidative Potential and Stable Interface in Lithium Metal Batteries

Poly(ethylene glycol) (PEG), despite being the most studied polymer electrolyte, suffers from serious drawbacks, which require fundamental studies behind its underperformance in lithium batteries. Here, we report the effect of the terminal group on triarm PEG stars bearing either hydroxyl (TPEG-OH) or carbonate-ketone (TPEG-Carb-ket) terminal groups. The latter is synthesized by a ring-opening reaction triggered by the -OH end group of TPEG-OH and results in a carbonate-ketone functionality. Indeed, the modified chain end is found to act as a sacrificial group by focusing the reactivity of the chain on the terminal group, protecting the rest of the TPEG molecule, which significantly reduces interfacial degradation and achieves a broader electrochemical stability window of up to 4.47 V, high Coulombic efficiency, and capacity retention. It furthermore demonstrates a stable interface with lithium metal after more than 1200 h of stripping and plating. When those electrolytes are investigated in reference cells based on LiFePO4 cathodes and Li anodes, the change in discharge capacity is observed from 118.7 to 113.8 and 108.9 to 5.03 mAh g-1 for TPEG-Carb-ket and TPEG-OH electrolytes, respectively, from the 1st to 100th cycle. The experimental results are further supported by density functional theory calculations and ab initio molecular dynamics simulations.

Synergistically Engineering Grains and Grain Boundaries toward Li Dendrite-Free Li7La3Zr2O12

Cation-doped cubic Li7La3Zr2O12 is regarded as a promising solid electrolyte for safe and energy-dense solid-state lithium batteries. However, it suffers from the formation of Li2CO3 and high electronic conductivity, which give rise to an unconformable Li/Li7La3Zr2O12 interface and lithium dendrites. Herein, composite AlF3-Li6.4La3Zr1.4Ta0.6O12 solid electrolytes were created based on thermal AlF3 decomposition and F/O displacement reactions under a high-temperature sintering process. When the AlF3 is thermally decomposed, it leaves Al2O3/AlF3 meliorating the grain boundaries and F- ions partially displacing O2- ions in the grains. Due to the higher electronegativity of F- in the grains and the grain-boundary modification, these AlF3-Li6.4La3Zr1.4Ta0.6O12 deliver optimized electronic conduction and chemical stability against the formation of Li2CO3. The Li/AlF3-Li6.4La3Zr1.4Ta0.6O12/Li cell exhibits a low interfacial resistance of ∼16 Ω cm2 and an ultrastable long-term cycling behavior for 800 h under a current density of 200 μA/cm2, leading to Li//LiCoO2 solid-state batteries with good rate performance and cycling stability.

In-Situ Construction of Electronically Insulating and Air-Stable Ionic Conductor Layer on Electrolyte Surface and Grain Boundary to Enable High-Performance Garnet-Type Solid-State Batteries

Lithophobic Li2CO3/LiOH contaminants and high-resistance lithium-deficient phases produced from the exposure of garnet electrolyte to air leads to a decrease in electrolyte ion transfer ability. Additionally, garnet electrolyte grain boundaries (GBs) with narrow bandgap and high electron conductivity are potential channels for current leakage, which accelerate Li dendrites generation, ultimately leading to short-circuiting of all-solid-state batteries (ASSBs). Herein, a stably lithiophilic Li2ZO3 is in situ constructed at garnet electrolyte surface and GBs by interfacial modification with ZrO2 and Li2CO3 (Z+C) co-sintering to eliminate the detrimental contaminants and lithium-deficient phases. The Li2ZO3 formed on the modified electrolyte (LLZTO-(Z+C)) surface effectively improves the interfacial compatibility and air stability of the electrolyte. Li2ZO3 formed at GBs broadens the energy bandgaps of LLZTO-(Z+C) and significantly inhibits lithium dendrite generation. More Li+ transport paths found in LLZTO-Z+C by first-principles calculations increase Li+ conductivity from 1.04×10-4 to 7.45×10-4 S cm-1. Eventually, the Li|LLZTO-(Z+C)|Li symmetric cell maintains stable cycling for over 2000 h at 0.8 mA cm-2. The capacity retention of LiFePO4|LLZTO-(Z+C)|Li battery retains 70.5% after 5800 ultralong cycles at 4 C. This work provides a potential solution to simultaneously enhance the air stability and modulate chemical characteristics of the garnet electrolyte surface and GBs for ASSBs.

In Situ Plasma Polymerization of Self-Stabilized Polythiophene Enables Dendrite-Free Lithium Metal Anodes with Ultra-Long Cycle Life

Constructing a flexible and chemically stable multifunctional layer for the lithium (Li) metal anodes is a highly effective approach to improve the uneven deposition of Li+ and suppress the dendrite growth. Herein, an organic protecting layer of polythiophene is in situ polymerized on the Li metal via plasma polymerization. Compared with the chemically polymerized thiophene (C-PTh), the plasma polymerized thiophene layer (P-PTh), with a higher Young's modulus of 8.1 GPa, shows strong structural stability due to the chemical binding of the polythiophene and Li. Moreover, the nucleophilic C─S bond of polythiophene facilitates the decomposition of Li salts in the electrolytes, promoting the formation of LiF-rich solid electrolyte interface (SEI) layers. The synergetic effect of the rigid LiF as well as the flexible PTh-Li can effectively regulate the uniform Li deposition and suppress the growth of Li dendrites during the repeated stripping-plating, enabling the Li anodes with long-cycling lifespan over 8000 h (1 mA cm-2, 1 mAh cm-2) and 2500 h (10 mA cm-2, 10 mAh cm-2). Since the plasma polymerization is facile (5-20 min) and environmentally friendly (solvent-free), this work offers a novel and promising strategy for the construction of the forthcoming generation of high-energy-density batteries.

An Elastomeric Lithium-Conducting Interlayer for High-Performance LATP-Based Lithium Metal Batteries

In response to the critical challenges of interfacial impedance and volumetric changes in Li(1+x)AlxTi(2‑x)(PO4)3 (LATP)-based lithium metal batteries, an elastomeric lithium-conducting interlayer fabricates from fluorinated hydrogenated nitrile butadiene rubber (F-HNBR) matrix is introduced herein. Owing to the vulcanization, vapor-phase fluorination, and plasticization processes, the lithium-conducting interlayer exhibits a high elasticity of 423%, exceptional fatigue resistance (10 000 compression cycles), superior ionic conductivity of 6.3 × 10-4 S cm-1, and favorable lithiophilicity, rendering it an ideal buffer layer. By integrating the F-HNBR interlayer, the LATP-based lithium symmetric cells demonstrate an extended cycle life of up to 1600 h at 0.1 mA cm-2 and can also endure deep charge/discharge cycles (0.5 mAh cm-2) for the same duration. Furthermore, the corresponding lithium metal full cells achieve 500 cycles at 0.5 C with 98.3% capacity retention and enable a high-mass-loading cathode of 11.1 mg cm-2 to operate at room temperature.

Review of the Real-Time Monitoring Technologies for Lithium Dendrites in Lithium-Ion Batteries

Lithium-ion batteries (LIBs) have the advantage of high energy density, which has attracted the wide attention of researchers. Nevertheless, the growth of lithium dendrites on the anode surface causes short life and poor safety, which limits their application. Therefore, it is necessary to deeply understand the growth mechanism of lithium dendrites. Here, the growth mechanism of lithium dendrites is briefly summarized, and the real-time monitoring technologies of lithium dendrite growth in recent years are reviewed. The real-time monitoring technologies summarized here include in situ X-ray, in situ Raman, in situ resonance, in situ microscopy, in situ neutrons, and sensors, and their representative studies are summarized. This paper is expected to provide some guidance for the research of lithium dendrites, so as to promote the development of LIBs.

Regulating Metal Centers of MOF-74 Promotes PEO-Based Electrolytes for All-Solid-State Lithium-Metal Batteries

Poly(ethylene oxide) (PEO)-based electrolytes have been extensively studied for all-solid-state lithium-metal batteries due to their excellent film-forming capabilities and low cost. However, the limited ionic conductivity and poor mechanical strength of the PEO-based electrolytes cannot prevent the growth of undesirable lithium dendrites, leading to the failure of batteries. Metal-organic frameworks (MOFs) are functional materials with a periodic porous structure that can improve the electrochemical performance of PEO-based electrolytes. However, the enhancement effect of MOFs with different metal centers and the interaction mechanism with PEO remain unclear. Herein, MOF-74s with Cu or Ni centers are prepared and used as fillers of PEO-based electrolytes. Adding 15 wt % of Cu-MOF-74 to the PEO-based electrolyte (15%Cu-MOF/P-Li) effectively improves the ionic conductivity, lithium transference number, and mechanical strength of the PEO-based electrolyte simultaneously. Furthermore, the ordered pore channels of Cu-MOF-74 provide uniform Li-ion transport pathways, facilitating homogeneous Li+ deposition. As a result, the lithium symmetric cell with 15%Cu-MOF/P-Li shows stable cycles for 1080 h at 0.1 mA cm-2 and 0.1 mAh cm-2, and the Li | 15% Cu-MOF/P-Li | LFP full cell exhibits a long cycle life up to 200 cycles at 60 °C and 0.5 C, with a capacity retention rate of 89.7%.

Solid Interfaces for the Garnet Electrolytes

Solid-state electrolytes (SSEs) have attracted extensive interests due to the advantages in developing secondary batteries with high energy density and outstanding safety. Possessing high ionic conductivity and the lowest reduction potential among the state-of-the-art SSEs, the garnet type SSE is one of the most promising candidates to achieve high performance solid-state lithium batteries (SSLBs). However, the elastic modulus of the garnet electrolyte leads to deteriorated interfacial contacts, and the increasing in electronic conduction at either anode/garnet interface or grain boundary results in Li dendrite growth. Here, recent developments of the solid interfaces for the garnet electrolytes, including the strategies of Li dendrite suppression and interfacial chemical/electrochemical/mechanical stabilizations are presented. A new viewpoint of the double edges of interfacial lithiophobicity is proposed, and the rational design of the interphases, as well as effective stacking methods of the garnet-based SSLBs are summarized. Moreover, practical roles of the garnet electrolyte in SSLB industry are also discussed. This work delivers insights into the solid interfaces for the garnet electrolytes, which provides not only the promotion of the garnet-based SSLBs, but also a comprehensive understanding of the interfacial stabilization for the whole SSE family.

Excellent Polymerized Ionic-Liquid-Based Gel Polymer Electrolytes Enabled by Molecular Structure Design and Anion-Derived Interfacial Layer

Polymerized ionic liquid (PIL)-based gel polymer electrolytes (GPEs) are well known as highly safe and stable electrolytes but with low ambient ionic conductivity. Herein, we first designed and synthesized an IL monomer with a long and flexible side chain and then mixed it with LiTFSI and MEMPTFSI to construct a PIL-based GPE (denoted as GM-GPE). The special molecular structure of the monomer greatly improves the ionic transport through the PIL chain, and the introduction of MEMPTFSI plasticizer further improves the ionic conductivity, promoting a TFSI--anion-derived SEI formation to suppress Li dendrite growth and forming an electrostatic shielding effect of MEMP+ cations to promote the uniform deposition of Li+. Consequently, the as-prepared GM-GPE exhibits high ambient ionic conductivity (4.3 × 10-4 S cm-1, 30 °C), robust electrochemical stability, excellent thermal stability, nonflammability, and superior ability to inhibit Li dendrite growth. The resultant LiFePO4|GM-GPE|Li cell exhibits a high discharge capacity of 150 mA h g-1 at 0.2 C along with a good cycling stability and rate capability. This work brings about new guidance for the development of high-quality GPEs with high ionic conductivity, high stability, and safety for long cycling and dendrite-free lithium metal batteries.

Recent Progress on the Air-Stable Battery Materials for Solid-State Lithium Metal Batteries

Solid-state lithium metal batteries (SSLMBs) offer numerous advantages in terms of safety and theoretical specific energy density. However, their main components namely lithium metal anode, solid-state electrolyte, and cathode, show chemical instability when exposed to humid air, which results in low capacities and poor cycling stability. Recent studies have shown that bioinspired hydrophobic materials with low specific surface energies can protect battery components from corrosion caused by humid air. Air-stable inorganic materials that densely cover the surface of battery components can also provide protection, which improves the storage stability of the battery components, broadens their processing conditions, and ultimately decreases their processing costs while enhancing their safety. In this review, the mechanism behind the surface structural degradation of battery components and the resulting consequences are discussed. Subsequently, recent strategies are reviewed to address this issue from the perspectives of lithium metal anodes, solid-state electrolytes, and cathodes. Finally, a brief conclusion is provided on the current strategies and fabrication suggestions for future safe air-stable SSLMBs.

Advances in Inorganic Solid-State Electrolyte/Li Interface

The increasing demand for high-energy-density and high-safety energy storage devices has sparked a growing interest in all-solid-state lithium metal batteries (ASSLMBs). A high-quality inorganic solid-state electrolyte (ISE) is a fundamental requirement for ASSLMBs, and an effective ISE/Li interface is a key factor in attaining high-performance ASSLMBs. In this Concept, we initially summarize the challenges encountered by ISE/Li interfaces and delineate four commonly employed strategies for modifying the ISE/Li interface. Then, we explore the merits and drawbacks of coatings utilized as ISE/Li interfacial phases. We also delve into the commonly employed thermal bonding and innovative cold bonding methods utilized for in situ interface preparation. Lastly, we spotlight future directions for enhancing the functionality of ISE/Li interfaces and achieving high-performance ASSLMBs.

Highly Efficient Aligned Ion-Conducting Network and Interface Chemistries for Depolarized All-Solid-State Lithium Metal Batteries

Improving the long-term cycling stability and energy density of all-solid-state lithium (Li)-metal batteries (ASSLMBs) at room temperature is a severe challenge because of the notorious solid-solid interfacial contact loss and sluggish ion transport. Solid electrolytes are generally studied as two-dimensional (2D) structures with planar interfaces, showing limited interfacial contact and further resulting in unstable Li/electrolyte and cathode/electrolyte interfaces. Herein, three-dimensional (3D) architecturally designed composite solid electrolytes are developed with independently controlled structural factors using 3D printing processing and post-curing treatment. Multiple-type electrolyte films with vertical-aligned micro-pillar (p-3DSE) and spiral (s-3DSE) structures are rationally designed and developed, which can be employed for both Li metal anode and cathode in terms of accelerating the Li+ transport within electrodes and reinforcing the interfacial adhesion. The printed p-3DSE delivers robust long-term cycle life of up to 2600 cycles and a high critical current density of 1.92 mA cm-2. The optimized electrolyte structure could lead to ASSLMBs with a superior full-cell areal capacity of 2.75 mAh cm-2 (LFP) and 3.92 mAh cm-2 (NCM811). This unique design provides enhancements for both anode and cathode electrodes, thereby alleviating interfacial degradation induced by dendrite growth and contact loss. The approach in this study opens a new design strategy for advanced composite solid polymer electrolytes in ASSLMBs operating under high rates/capacities and room temperature.

Enhancing Fast-Charge Capabilities in Solid-State Lithium Batteries through the Integration of High Li0.5La0.5TiO3 (LLTO) Content in the Lithium-Metal Anode

Solid-state batteries (SSBs), which have high energy density and are safe, are recognized as an important field of study. However, the poor interfacial contact with high resistance, the dendrite problem, and the volume change of the metallic lithium anode prevent the use of SSBs. Li0.5La0.5TiO3 (LLTO) particles and molten lithium were used to create a high-performance LLTO-Li composite lithium with a sequential ion-conducting phase. With garnet electrolytes, this lithium has better wettability and reduced surface tension. To compensate for the lithium depletion that occurs during stripping, the Li-Ti phase with a high ionic diffusion coefficient that forms in the anode can rapidly transport lithium from the bulk to the solid-state interface, ensuring tight interface contact, preventing the formation of gaps, and homogenizing the current and Li+ flux. The LLTO-Li| LLZTO| LLTO-Li symmetric cell exhibits a good cyclic stability of 1000 h at room temperature, a low interfacial resistance of 22 Ω cm2, and a high critical current density of 1.2 mA cm-2. Furthermore, fully built cells with a LiFePO4 cathode showed outstanding cycling performance, maintaining 95% of their capacity after 900 cycles at 1 C and 92% capacity retention after 100 cycles at 2 C.

Synergized Tricomponent All-Inorganics Solid Electrolyte for Highly Stable Solid-State Li-Ion Batteries

Garnet-type oxide Li6.4 La3 Zr1.4 Ta0.6 O12 (LLZTO) features superior ionic conductivity and good stability toward lithium (Li) metal, but requires high-temperature sintering (≈1200 °C) that induces high fabrication cost, poor mechanical processability, and high interface resistance. Here, a novel high-performance tricomponent composite solid electrolyte (CSE) comprising LLZTO-4LiBH4 /xLi3 BN2 H8 is reported, which is prepared by ball milling the LLZTO-4LiBH4  mixture followed by hand milling with Li3 BN2 H8 . Green pellets fabricated by heating the cold-pressed CSE powders at 120 °C offer ultrafast room-temperature ionic conductivity (≈1.73 × 10-3  S cm-1  at 30 °C) and ultrahigh Li-ion transference number (≈0.9999), which enable the Li|Li symmetrical cells to cycle over 1600 h at 30 °C with only 30 mV of overpotential. Moreover, the Li|CSE|TiS2  full cells deliver 201 mAh g-1  of capacity with long cyclability. These outstanding performances are due to the low open porosity in the electrolyte pellets as well as the high intrinsic ionic conductivity and easy deformability of Li3 BN2 H8 .

Composite electrolytes engineered by anion acceptors for boosted high-voltage solid-state lithium metal batteries

Solid-state batteries (SSBs) are considered as the most promising option to replace commercial lithium-ion batteries due to their ability to address the flammability of liquid organic electrolytes and facilitate the energy density of lithium batteries. Herein, by introducing tris(trimethylsilyl) borate (TMSB) as anion acceptors, we successfully develop the light and thin electrolyte (TMSB-PVDF-HFP-LLZTO-LiTFSI, PLFB) with a wide voltage window to couple the lithium metal anode with the high-voltage cathodes. Consequently, as-prepared PLFB can greatly boost the generation of free Li⁺ and improve the Li⁺ transference numbers (t_Li+=0.92) at room temperature. Moreover, combined with theoretical calculation and experimental results, the changes in the composition and properties of the composite electrolyte membrane with the addition of anionic receptors are systematically studied, which further implies the intrinsic mechanism of the stability difference. In addition, the PLFB-based SSB assembled by LiNi_0.8Co_0.1Mn_0.1O₂ cathode and lithium anode exhibits a high capacity retention of 86% after loop 400 cycles. This investigation on boosted battery performance by immobilized anions not only contributes to the directional construction of dendrite-free and lithium-ion permeable interface, but also brings new opportunities for the screening and design of the next generation of high-energy SSBs.

Phase-Changeable Dynamic Conformal Electrode/electrolyte Interlayer enabling Pressure-Independent Solid-State Lithium Metal Batteries

Lithium-metal-based solid-state batteries (Li-SSBs) are one of the most promising energy storage devices due to their high energy densities. However, under insufficient pressure constraints (<MPa-level), Li-SSBs usually exhibit poor electrochemical performances owing to the continuous interfacial degradation between the solid-state electrolyte (SSE) and electrodes. Herein, a phase-changeable interlayer is developed to construct the self-adhesive and dynamic conformal electrode/SSE contact in Li-SSBs. The strong adhesive and cohesive strengths of the phase-changeable interlayer enable Li-SSBs to resist up to 250 N pulling force (=1.9 MPa), affording Li-SSBs ideal interfacial integrality even without extra stack pressure. Remarkably, this interlayer exhibits a high ionic conductivity of 1.3 × 10^-3 S cm^-1 , attributed to the shortened steric solvation hindrance and optimized Li⁺ coordination structure. Furthermore, the changeable phase property of the interlayer endows Li-SSBs with a healable Li/SSE interface, accommodating the stress-strain evolution of the lithium metal and constructing the dynamic conformal interface. Consequently, the contact impedance of the modified solid symmetric cell exhibits a pressure-independent manner and does not increase over 700 h (0.2 MPa). The LiFePO₄ pouch cell with the phase-changeable interlayer shows 85% capacity retention after 400 cycles at a low pressure of 0.1 MPa.

Engineering Li Metal Anode for Garnet-Based Solid-State Batteries

ConspectusThe past 30 years have witnessed the great achievements of Li-ion batteries (LIBs) based on a graphite anode and liquid organic electrolytes. Yet the limited energy density of a graphite anode and unavoidable safety risks caused by flammable liquid organic electrolytes hinder further developments of LIBs. To reach higher energy density, Li metal anodes (LMAs) with high capacity and low electrode potential are a promising choice. However, LMAs suffer from more serious safety concerns than the graphite anode in liquid LIBs. The dilemma of safety and energy density remains an inevitable obstacle in the way of LIBs.Solid-state batteries (SSBs) offer new opportunities to simultaneously achieve intrinsic safety and high energy density. Among all types of SSBs that are based on oxides, polymers, sulfides, or halides, garnet-type SSBs seem to be one of the most attractive choices due to garnet's merits in high ionic conductivities (10^-4-10^-3 S/cm at room temperature), wide electrochemical windows (0-6 V), and intrinsically high safety. However, garnet-type SSBs are faced with large interfacial impedance and short-circuit problems caused by Li dendrites. Recently, engineered Li metal anodes (ELMAs) have shown unique advantages in tackling interface issues and attracted extensive research interest.In this Account, we focus on fundamental understandings and provide an in-depth review of ELMAs in garnet-based SSBs. Considering the limited space, we mainly discuss the recent progress made in our groups. First, we introduce the design guidelines for ELMAs and emphasize the unique role of theoretical calculation in predicting and optimizing ELMAs. Then we discuss the interface compatibility of ELMAs with garnet SSEs in details. Specifically, we have demonstrated the advantages of ELMAs in enhancing interface contact and suppressing Li dendrite growth. Next, we attentively analyze the gaps between laboratory and practical applications. We strongly recommend establishing a unified testing standard, with a practically desired areal capacity per cycle (>3.0 mAh/cm²) and a precisely controlled Li capacity excess. Finally, novel chances to enhance ELMAs' processability and fabricate thin Li foils are highlighted. We believe that this Account will offer an insightful analysis of ELMAs' recent advancements and push forward their practical applications.

Al and Ta co-doped LLZO as active filler with enhanced Li+conductivity for PVDF-HFP composite solid-state electrolyte

Battery safety calls for solid state batteries and how to prepare solid electrolytes with excellent performance are of significant importance. In this study, hybrid solid electrolytes combined with organic PVDF-HFP and inorganic active fillers are studied. The modified active fillers of Li_7-x-3yAl_yLa₃Zr_2-xTa_xO₁₂are obtained by co-element doping with Al and Ta when LLZO is synthesized by calcination. And an high room temperature ionic conductivity of 5.357 × 10^-4S cm^-1is exhibited by ATLLZO ceramic sheet. The composite solid electrolyte PVDF-HFP/LiTFSI/ATLLZO (PHL-ATLLZO) is prepared by solution casting method, and its electrochemical properties are investigated. The results show that when the contents of lithium salt LiTFSI and active filler ATLLZO are controlled at 40 wt% and 10%, respectively, the ionic conductivity of the resulting composite solid electrolyte is as high as 2.686 × 10^-4S cm^-1at room temperature, and a wide electrochemical window of 4.75 V is exhibited. The LiFePO₄/PHL-ATLLZO/Li all-solid-state battery assembled based on the composite solid-state electrolyte exhibits excellent cycling stability at room temperature. The cell assembled by casting the composite solid-state electrolyte on the cathode surface shows a discharge specific capacity of 134.3 mAh g^-1and 96.2% capacity retention after 100 cycles at 0.2 C. The prepared composite solid-state electrolyte demonstrates excellent electrochemical performance.

Phase Separation-Controlled Assembly of Hierarchically Porous Aramid Nanofiber Films for High-speed Lithium-Metal Batteries

The growth of lithium (Li) dendrites reduces the lifespan of Li-metal batteries and causes safety issues. Herein, hierarchically porous aramid nanofiber separators capable of effectively suppressing the Li dendrite growth while maintaining highly stable cycle performances at high charge/discharge rates are reported. A two-step solvent exchange process combined with reprotonation-mediated self-assembly is utilized to control the bimodal porous structure of the separators. In particular, when ethanol and water are used sequentially, aramid nanofibers form hierarchical porous structures containing nanopores in macroporous polymer frameworks to yield a mechanically robust membrane with high porosity of 97% or more. The optimized samples exhibit high ionic conductivities of 1.87-4.04 mS cm^-1 and high Li-ion transference numbers of 0.77-0.84 because of the ultrahigh porosity and selective affinity to anions. Li-metal symmetric cells do not show any noticeable presence of dendrites after 100 cycles, and they operate stably for more than 1500 cycles even under extreme conditions with a high current density of >20 mA cm^-2 . In addition, the LiFePO₄ /Li full cell retains 86.3% of its capacity after 1000 cycles at a charge rate of 30 C.

A Silica-Reinforced Composite Electrolyte with Greatly Enhanced Interfacial Lithium-Ion Transfer Kinetics for High-Performance Lithium Metal Batteries

Developing quasi-solid-state electrolytes with superior ionic conductivity and high mechanical strength is urgently desired to improve the safety and cycling stability of lithium-metal batteries. Herein, a novel solid-like electrolyte (SLE) with enhanced Li⁺ interfacial transfer kinetics is rationally designed by soaking bulk nanostructured silica-polymer composites in liquid electrolytes. Benefiting from the high content of inorganic silica and abundant interfaces for fast Li⁺ -transport channels, the prepared SLE exhibits superb ionic conductivity and high mechanical strength. Furthermore, fumed silica with a high specific area in the SLE can homogenize Li⁺ flux and electrical field gradient. More importantly, a Li₂ S-rich solid electrolyte interphase (SEI) is constructed on the lithium metal due to the intimate ion coordination in the SLE. Therefore, the lithium-metal anode exhibits excellent electrochemical performance in symmetric Li-Li cells due to the merits of superior ionic conductivity, high modulus, Li₂ S-rich SEI, as well as the homogeneous Li⁺ flux. Full cells with LiFePO₄ cathode can still display a capacity retention of 98% at 0.2 C after 400 cycles. The proposed strategy on quasi-solid-state electrolytes provides a promising avenue for next-generation metal-based batteries.

Bio-Based Solid Electrolytes Bearing Cyclic Carbonates for Solid-State Lithium Metal Batteries

Green resources for lithium-based batteries excite many researchers due to their eco-friendly nature. In this work, a sustainable bio-based solid-state electrolyte was developed based on carbonated soybean oil (CSBO), obtained by organocatalyzed coupling of CO₂ to epoxidized soybean oil. CSBO coupled with lithium bis(trifluoromethanesulfonyl)imide salt on a bio-based cellulose separator resulted in free-standing membranes. Those membranes on electrochemical measurements exhibited ionic conductivity of around 10^-3  S cm^-1 at 100 °C and around 10^-6  S cm^-1 at room temperature with wide electrochemical stability window (up to 4.6 V vs. Li/Li⁺ ) and transference number up to 0.39 at RT. Further investigations on the galvanostatic charge-discharge of LiFePO₄ cathodes with CSBO-based electrolyte membranes and lithium metal anodes delivered the gravimetric capacity of 112 and 157 mAh g^-1 at RT and 60 °C, respectively, providing a promising direction to further develop bio-based solid electrolytes for sustainable solid-state lithium batteries.

Grain Boundary Engineering Enabled High-Performance Garnet-Type Electrolyte for Lithium Dendrite Free Lithium Metal Batteries

Solid-state lithium metal batteries (SSLMBs) are attracting increasing attentions as one of the promising next-generation technologies due to their high-safety and high-energy density. Their practical application, however, is hindered by lithium dendrite growth and propagation in solid-state electrolytes (SSEs). Herein, an in situ grain boundary modification strategy relying on the reaction between Li₂ TiO₃ (LTO) and Ta-substituted garnet-type electrolyte (LLZT) is developed, which forms LaTiO₃ along with lesser amounts of LTO/Li₂ ZrO₃ at the grain boundaries (GBs). The second phases of LTO/Li₂ ZrO₃ inhibit abnormal grain growth. The presence of LaTiO₃ at the GBs reduces electronic conductivity and improves mechanical strength, which can hinder dendrite formation and block lithium dendrite penetration through the LLZT. Moreover, the adjacent grains by LaTiO₃ build a continuous Li⁺ transport path, providing a homogeneous Li⁺ flux throughout the whole LLZT-4LTO. As a result, symmetric cells of Li | LLZT-4LTO | Li shows a high critical current density of 1.8 mA cm^-2 and a long cycling stability up to 2000 h at 0.3 mA cm^-2 . Moreover, the high-voltage full cells demonstrate remarkable cycling stability and rate performance. It is believed that this novel grain boundary modification strategy can shed light on the constructing of high-performance SSEs for practical SSLMBs.

Ultrafast Sintering for Ceramic-Based All-Solid-State Lithium-Metal Batteries

Long processing time and high temperatures are often required in sintering ceramic electrolytes, which lead to volatile element loss and high cost. Here, an ultrafast sintering method of microwave-induced carbothermal shock to fabricate various ceramic electrolytes in seconds is reported. Furthermore, it is also possible to integrate the electrode and electrolyte in one step by simultaneous co-sintering. Based on this ultrafast co-sintering technique, an all-solid-state lithium-metal battery with a high areal capacity is successfully achieved, realizing a promising electrochemical performance at room temperature. This method can extend to other various ceramic multilayer-based solid devices.

Issues Concerning Interfaces with Inorganic Solid Electrolytes in All-Solid-State Lithium Metal Batteries

All-solid-state batteries have attracted wide attention for high-performance and safe batteries. The combination of solid electrolytes and lithium metal anodes makes high-energy batteries practical for next-generation high-performance devices. However, when a solid electrolyte replaces the liquid electrolyte, many different interface/interphase issues have arisen from the contact with electrodes. Poor wettability and unstable chemical/electrochemical reaction at the interfaces with lithium metal anodes will lead to poor lithium diffusion kinetics and combustion of fresh lithium and active materials in the electrolyte. Element cross-diffusion and charge layer formation at the interfaces with cathodes also impede the lithium ionic conductivity and increase the charge transfer resistance. The abovementioned interface issues hinder the electrochemical performance of all-solid-state lithium metal batteries. This review demonstrates the formation and mechanism of these interface issues between solid electrolytes and anodes/cathodes. Aiming to address the problems, we review and propose modification strategies to weaken interface resistance and improve the electrochemical performance of all-solid-state lithium metal batteries.

A Multifunctional Silicon-Doped Polyether Network for Double Stable Interfaces in Quasi-Solid-State Lithium Metal Batteries

Polymer-based quasi-solid-state electrolyte (QSE) is an effective means to solve the safety problem of lithium (Li) metal batteries, and stable solid-electrolyte-interface (SEI) layers between electrolyte and anode/cathode are highly required for their long-term stability. Herein, it is demonstrated that a silicon-doped polyether functions as a multifunctional unit, which can induce the formation of stable and robust SEI layers with rich Li_x SiO_y on both the surfaces of cathode and anode. It simultaneously solves the compatibility of electrolyte and electrodes in the quasi-solid-state Li-metal battery. Moreover, the robust polymer skeleton with a cross-linked network is beneficial to inhibit liquid volatilization and improve battery safety. The assembled Li|QSE|LiFePO₄ batteries show a capacity retention rate as high as 97.5% after 400 cycles at 1 C (30 °C), and reach 78.1% after 1000 cycles. Furthermore, there is almost no attenuation of reversible capacity after 100 cycles for the assembled Li|QSE|LiNi_0.8 Mn_0.1 Co_0.1 O₂ batteries. The concept of silicon-doped polymer with a crosslinking structure provides an important strategy for designing solid-state or quasi-solid-state polymer electrolytes for the stable long-term operation of both anode and cathode.

Crystal Channel Engineering for Rapid Ion Transport: From Nature to Batteries

Ion transport behaviours through cell membranes are commonly identified in biological systems, which are crucial for sustaining life for organisms. Similarly, ion transport is significant for electrochemical ion storage in rechargeable batteries, which has attracted much attention in recent years. Rapid ion transport can be well achieved by crystal channels engineering, such as creating pores or tailoring interlayer spacing down to the nanometre or even sub-nanometre scale. Furthermore, some functional channels, such as ion selective channels and stimulus-responsive channels, are developed for smart ion storage applications. In this review, the typical ion transport phenomena in the biological systems, including ion channels and pumps, are first introduced, and then ion transport mechanisms in solid and liquid crystals are comprehensively reviewed, particularly for the widely studied porous inorganic/organic hybrid crystals and ultrathin inorganic materials. Subsequently, recent progress on the ion transport properties in electrodes and electrolytes is reviewed for rechargeable batteries. Finally, current challenges in the ion transport behaviours in rechargeable batteries are analysed and some potential research approaches, such as bioinspired ultrafast ion transport structures and membranes, are proposed for future studies. It is expected that this review can give a comprehensive understanding on the ion transport mechanisms within crystals and provide some novel design concepts on promoting electrochemical ion storage capability in rechargeable batteries.

Facile In Situ Chemical Cross-Linking Gel Polymer Electrolyte, which Confines the Shuttle Effect with High Ionic Conductivity and Li-Ion Transference Number for Quasi-Solid-State Lithium-Sulfur Battery

As a secondary Li-ion battery with high energy density, lithium-sulfur (Li-S) batteries possess high potential development prospects. One of the important ingredients to improve the safety and energy density in Li-S batteries is the solid-state electrolyte. However, the poor ionic conductivity largely limits its application for the commercial market. At present, the gel electrolyte prepared by combining the electrolyte or ionic liquid with the all-solid electrolyte is an effective method to solve the low ion conductivity of the solid electrolyte. We present a cross-linked gel polymer electrolyte with fluoroethylene carbonate (FEC) as a solid electrolyte interface (SEI) film formed for Li-S quasi-solid-state batteries, which can be simply synthesized without initiators. This gel polymer electrolyte with FEC as an additive (GPE@FEC) possesses high ionic conductivity (0.830 × 10^-3 S/cm at 25 °C and 1.577 × 10^-3 S/cm at 85 °C) and extremely high Li-ion transference number (t_Li⁺ = 0.674). In addition, the strong ability toward anchoring polysulfides resulting in the high electrochemical performance of Li-S batteries was confirmed in GPE@FEC by the diffusion experiment, X-ray photoelectron spectroscopy analysis (XPS), and scanning electron microscopy (SEM) mapping of the S element. Such a high ion conductivity (IC) gel polymer electrolyte enables a competitive specific capacity of 940 mAh/g at 0.2C and supreme cycling performance for 180 cycles at 0.5C, which is far beyond that of conventional poly(ethylene oxide)-based quasi-solid-state Li-S batteries.

Universal lithiophilic interfacial layers towards dendrite-free lithium anodes for solid-state lithium-metal batteries

Solid-state lithium-metal batteries (SSLMBs) using garnet Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO) as the solid electrolyte are expected to conquer the safety concerns of high energy Li batteries with organic liquid electrolytes owing to its nonflammable nature and good mechanical strength. However, the poor interfacial contact between the Li anode and LLZTO greatly restrains the practical applications of the electrolyte, because large polarization, dendritic Li formation and penetration can occur at the interfaces. Here, an effective method is proposed to improve the wettability of the LLZTO toward lithium and reduce the interfacial resistance by engineering universal lithiophilic interfacial layers. Thanks to the in-situ formed lithiophilic and ionic conductive Co/Li₂O interlayers, the symmetric Li/CoO-LLZTO/Li batteries present much smaller overpotential, ultra-low areal specific resistance (ASR, 12.3 Ω cm²), high critical current density (CCD, 1.1 mA cm^-2), and outstanding cycling performance (1696 h at a current density of 0.3 mA cm^-2) at 25 °C. Besides, the solid-state Li/CoO-LLZTO/LFP cells deliver an excellent electrochemical performance with a high coulombic efficiency of ~100% and a long cycling time over 185 times. Surprisingly, the high-voltage (4.6 V) solid state Li/CoO-LLZTO/Li_1.4Mn_0.6Ni_0.2Co_0.2O_2.4 (LMNC622) batteries can also realize an ultra-high specific capacity (232.5 mAh g^-1) under 0.1 C at 25 °C. This work paves an effective way for practical applications of the dendrite-free SSLMBs.

Covalent Organic Frameworks and Their Derivatives for Better Metal Anodes in Rechargeable Batteries

Metal anodes based on a plating/stripping electrochemistry such as metallic Li, Na, K, Zn, Ca, Mg, Fe, and Al are recognized as promising anode materials for constructing next-generation high-energy-density rechargeable metal batteries owing to their low electrochemical potential, high theoretical specific capacity, superior electronic conductivity, etc. However, inherent issues such as high chemical reactivity, severe growth of dendrites, huge volume changes, and unstable interface largely impede their practical application. Covalent organic frameworks (COFs) and their derivatives as emerging multifunctional materials have already well addressed the inherent issues of metal anodes in the past several years due to their abundant metallophilic functional groups, special inner channels, and controllable structures. COFs and their derivatives can solve the issues of metal anodes by interfacial modification, homogenizing ion flux, acting as nucleation seeds, reducing the corrosion of metal anodes, and so on. Nevertheless, related reviews are still absent. Here we present a detailed review of multifunctional COFs and their derivatives in metal anodes for rechargeable metal batteries. Meanwhile, some outlooks and opinions are put forward. We believe the review can catch the eyes of relevant researchers and supply some inspiration for future research.

Unveiling the Role of Li+ Solvation Structures with Commercial Carbonates in the Formation of Solid Electrolyte Interphase for Lithium Metal Batteries

Solid electrolyte interphase (SEI), determined by the components of electrolytes, can endow batteries with the ability to repress the growth of Li dendrites. Nevertheless, the mechanism of commercial carbonates on in situ-generated SEI and the consequential effect on cycling performance is not well understood yet, although some carbonates are well used in electrolytes. In this work, quantum chemical calculations and molecular dynamics are used to reveal the formation mechanisms of SEI with carbonate-based electrolyte additives on the atomic level. It is confirmed that the Li-coordinated carbonate species are the leading participant of SEI formation and their impact on battery performance is clarified. Fluoroethylene carbonate (FEC) exhibits a completely different behavior from vinyl ethylene carbonate (VEC), ethylene carbonate (EC), and vinylene carbonate (VC). High reduction potential Li⁺ -coordinated additives, e.g. FEC and VEC can dominate the formation of SEI by excluding propylene carbonate (PC) and LiPF₆ from the decomposition, and the corresponding Li||Li symmetric cells show enhanced long-term performance compared with those with pure PC electrolyte, while the low reduction priority additives (e.g., EC and VC) cannot form a uniform SEI by winning the competitive reaction.

Dislocations in ceramic electrolytes for solid-state Li batteries

High power solid-state Li batteries (SSLB) are hindered by the formation of dendrite-like structures at high current rates. Hence, new design principles are needed to overcome this limitation. By introducing dislocations, we aim to tailor mechanical properties in order to withstand the mechanical stress leading to Li penetration and resulting in a short circuit by a crack-opening mechanism. Such defect engineering, furthermore, appears to enable whisker-like Li metal electrodes for high-rate Li plating. To reach these goals, the challenge of introducing dislocations into ceramic electrolytes needs to be addressed which requires to establish fundamental understanding of the mechanics of dislocations in the particular ceramics. Here we evaluate uniaxial deformation at elevated temperatures as one possible approach to introduce dislocations. By using hot-pressed pellets and single crystals grown by Czochralski method of Li6.4La3Zr1.4Ta0.6O12 garnets as a model system the plastic deformation by more than 10% is demonstrated. While conclusions on the predominating deformation mechanism remain challenging, analysis of activation energy, activation volume, diffusion creep, and the defect structure potentially point to a deformation mechanism involving dislocations. These parameters allow identification of a process window and are a key step on the road of making dislocations available as a design element for SSLB.

First-Principles Study of Microscopic Electrochemistry at the LiCoO2 Cathode/LiNbO3 Coating/β-Li3PS4 Solid Electrolyte Interfaces in an All-Solid-State Battery

High interfacial resistance between electrode and solid electrolyte (SE) is one of the major challenges for the commercial application of all-solid-state batteries (ASSBs), and coating at the interface is an effective way for decreasing the resistance. However, microscopic electrochemistry especially for the electrochemical potential and the distribution of Li⁺ at the interface has not been well established yet, impeding the in-depth understanding of interfacial Li⁺ transport. Herein, we have introduced a potential energy profile for Li⁺, η_Li⁺, and demonstrated that the interfacial η_Li⁺ can be evaluated from the calculated interfacial Li vacancy formation energy or the bulk vacancy formation energy and the interface band alignment. Through computational analysis of the representative LiCoO₂ cathode/LiNbO₃ coating/β-Li₃PS₄ SE interfaces using the novel interface structure prediction scheme based on the CALYPSO method, we found that η_Li⁺ at the LiCoO₂/β-Li₃PS₄ interface is highly disordered under the influence of the interface reconstruction and is rather electronic conductive. Insertion of LiNbO₃ coating can effectively decrease the preference of ion mixing. Besides, the appropriate changes in band alignments lead to a decrease of difference in the interfacial η_Li⁺ and lower resistances at the interfaces. The results provide a reliable explanation for the effectiveness of the coating layer observed experimentally. Furthermore, our study provides a guidance for the future simulation of the microscopic electrochemistry at the electrode/SE interfaces in ASSBs.

Interface Issues and Challenges in All-Solid-State Batteries: Lithium, Sodium, and Beyond

Owing to the promise of high safety and energy density, all-solid-state batteries are attracting incremental interest as one of the most promising next-generation energy storage systems. However, their widespread applications are inhibited by many technical challenges, including low-conductivity electrolytes, dendrite growth, and poor cycle/rate properties. Particularly, the interfacial dynamics between the solid electrolyte and the electrode is considered as a crucial factor in determining solid-state battery performance. In recent years, intensive research efforts have been devoted to understanding the interfacial behavior and strategies to overcome these challenges for all-solid-state batteries. Here, the interfacial principle and engineering in a variety of solid-state batteries, including solid-state lithium/sodium batteries and emerging batteries (lithium-sulfur, lithium-air, etc.), are discussed. Specific attention is paid to interface physics (contact and wettability) and interface chemistry (passivation layer, ionic transport, dendrite growth), as well as the strategies to address the above concerns. The purpose here is to outline the current interface issues and challenges, allowing for target-oriented research for solid-state electrochemical energy storage. Current trends and future perspectives in interfacial engineering are also presented.

Lithium/Sulfide All-Solid-State Batteries using Sulfide Electrolytes

All-solid-state lithium batteries (ASSLBs) are considered as the next generation electrochemical energy storage devices because of their high safety and energy density, simple packaging, and wide operable temperature range. The critical component in ASSLBs is the solid-state electrolyte. Among all solid-state electrolytes, the sulfide electrolytes have the highest ionic conductivity and favorable interface compatibility with sulfur-based cathodes. The ionic conductivity of sulfide electrolytes is comparable with or even higher than that of the commercial organic liquid electrolytes. However, several critical challenges for sulfide electrolytes still remain to be solved, including their narrow electrochemical stability window, the unstable interface between the electrolyte and the electrodes, as well as lithium dendrite formation in the electrolytes. Herein, the emerging sulfide electrolytes and preparation methods are reviewed. In particular, the required properties of the sulfide electrolytes, such as the electrochemical stabilities of the electrolytes and the compatible electrode/electrolyte interfaces are highlighted. The opportunities for sulfide-based ASSLBs are also discussed.

Enhanced ionic conductivity and lithium dendrite suppression of polymer solid electrolytes by alumina nanorods and interfacial graphite modification

Poor room-temperature ionic conductivity and lithium dendrite formation are the main issues of solid electrolytes. In this work, rod-shaped alumina incorporation and graphite coating were simultaneously applied to poly (propylene carbonate) (PPC)-based polymer solid electrolytes (Wang et al., 2018). The obtained alumina modified solid electrolyte membrane (Al-SE) achieves a high ionic conductivity of 3.48 × 10^-4 S/cm at room temperature with a wide electrochemical window of 4.6 V. The assembled NCM622/Al-SE/Li solid-state battery exhibits initial discharge capacities of 198.2 mAh/g and 177.5 mAh/g at the current density of 0.1 C and 0.5 C, with the remaining capacities of 165.8 mAh/g and 161.3 mAh/g after 100 cycles respectively. The rod-shaped structure of Al₂O₃ provides fast transport channels for lithium ions and its Lewis acidity promotes the dissociation of lithium salts and release of free lithium ions. The lithiophilic Al₂O₃ and Graphite form intimate contact with metallic Li and create fast Li⁺ conductive layers of Li-Al-O layer and LiC₆ layer, thus facilitating the uniform deposition of Li and inhibiting Li dendrite formation during long-term cycling. This kind of composite Al-SE is expected to provide a promising alternative for practical application in solid electrolytes.

Integrated Structure of Cathode and Double-Layer Electrolyte for Highly Stable and Dendrite-Free All-Solid-State Li-Metal Batteries

All-solid-state batteries have become the most potential next-generation energy-storage devices. However, it is quite difficult to simultaneously achieve a single solid-state electrolytes (SSEs) layer with both dendrite-free Li metal plating and low interfacial resistance between the cathode and SSEs. Herein, an integrated structure of cathode and double-layer solid electrolyte membrane (IS-CDL) is designed, which greatly improves the interfacial contact and suppresses the Li dendrite growth. The first "polymer in ceramic" solid electrolyte layer (SL1) consists of 80 wt % Li_1.4Al_0.4Ti_1.6(PO₄)₃ (LATP) nanoparticles and 20 wt % polyethylene oxide (PEO), and the second polymer electrolyte layer is PEO-based solid electrolyte layer (SL2). The SL1 with high mechanical properties can hinder the growth of Li dendrites and reduce the interfacial resistance with the cathode. The SL2 can inhibit the side reaction between the Li metal and LATP. The Li symmetric cells with sandwich-type hierarchical electrolyte (SL2/SL1/SL2) can stably cycle over 3200 h at 0.1 mA cm^-2 at 45 °C. The obtained all-solid-state LiFePO₄-IS-CDL/Li batteries present a capacity of 142.6 mA h g^-1 at 45 °C with the capacity retention of 91.7% after 100 cycles, and all-solid-state NCM811-IS-CDL/Li batteries deliver a specific capacity of 175.5 mA h g^-1 at 60 °C. This work proposes an effective strategy to fabricate all-solid-state lithium batteries with high electrochemical performance.

3D Coral-like LLZO/PVDF Composite Electrolytes with Enhanced Ionic Conductivity and Mechanical Flexibility for Solid-State Lithium Batteries

Composite polymer electrolytes (CPEs) are very promising for high-energy lithium-metal batteries as they combine the advantages of polymeric and ceramic electrolytes. The dimensions and morphologies of active ceramic fillers play critical roles in determining the electrochemical and mechanical performances of CPEs. Herein, a coral-like LLZO (Li_6.4La₃Zr₂Al_0.2O₁₂) is designed and used as a 3D active nanofiller in a poly(vinylidene difluoride) polymer matrix. Building 3D interconnected frameworks endows the as-made CPE membranes with an enhanced ionic conductivity (1.51 × 10^-4 S cm^-1) at room temperature and an enlarged tensile strength up to 5.9 MPa. As a consequence, the flexible 3D-architectured CPE enables a steady lithium plating/stripping cycling over 200 h without a short circuit. Moreover, the assembled solid-state Li|LiFePO₄ cells using the electrolyte exhibit decent cycling performance (95.2% capacity retention after 200 cycles at 1 C) and excellent rate capability (120 mA h g^-1 at 3 C). These results demonstrate the superiority of 3D interconnected garnet frameworks in developing CPEs with excellent electrochemical and mechanical properties.

Stabilizing a Lithium Metal Battery by an In Situ Li2S-modified Interfacial Layer via Amorphous-Sulfide Composite Solid Electrolyte

A novel strategy has been proposed to produce in situ Li₂S at the interfacial layer between lithium anode and the solid electrolyte, by using an amorphous-sulfide-LiTFSI-poly(vinylidene difluoride) (PVDF) composite solid electrolyte (SLCSE). Besides retarding the decomposition of PVDF in CSE, the Li₂S-modified interfacial layer (SMIL) also improves the wettability between lithium metal and SLCSE which in turn optimizes the lithium deposition process. Our density functional theory calculation results reveal that the migration energy barrier of Li passing through SMIL is much lower than that of Li passing through LiF-modified interfacial layer (FMIL) formed from the decomposition of PVDF. The as-prepared SLCSE shows a Li ionic transference number of 0.44 and Li ion conductivity of 3.42 × 10^-4 S/cm at room temperature, and the Li||SLCSE||LiFePO₄ cell exhibits an outstanding rate performance with a capacity of 153, 144, 131, and 101 mAh/g at a current density of 0.05, 0.10, 0.25, and 0.50 mA/cm², respectively.

Nanoengineered Organic Electrodes for Highly Durable and Ultrafast Cycling of Organic Sodium-Ion Batteries

Sodium-ion batteries (SIBs) have become increasingly important as next-generation energy storage systems for application in large-scale energy storage. It is very crucial to develop an eco-friendly and green SIB technique with superior performance for sustainable future use. Replacing the conventional inorganic electrode materials with green and safe organic electrodes will be a promising approach. However, the poor electrochemical kinetics, unstable electrode-electrolyte interface, high solubility of the electrodes in the electrolyte, and large amount of conductive carbon present great challenges for organic SIBs. In this study, the issues of organic electrodes are addressed through atomic-level manipulation of these organic molecules using a series of ultrathin (Å-level) metal oxide coatings (Al₂ O₃ , ZnO, and TiO₂ ). Uniform and precise coatings on the perylene-3,4,9,10-tetracarboxylicacid dianhydride by gas-phase atomic layer deposition technique shows a stable interphase, enhanced electrochemical kinetics (71C, 10 A g^-1 ), and excellent stability (89%-500 cycles) compared to conventional organic electrode (70%-200 cycles). Further studies reveal that the chemical stability of the metal oxide coating layer plays a critical role in influencing the redox behavior, and improving kinetics of organic electrodes. This study opens a new avenue for developing high-energy organic SIBs with performance equivalent to inorganic counterparts.

A Lithium Metal Anode Surviving Battery Cycling Above 200 °C

Lithium (Li) metal electrode cannot endure elevated temperature (e.g., >200 °C) with the regular battery configuration due to its low melting point (180.5 °C) and high reactivity, which restricts its application in high-temperature Li metal batteries for energy storage and causes safety concerns for regular ambient-temperature Li metal batteries. Herein, this work reports a Li₅ B₄ /Li composite featuring a 3D Li₅ B₄ fibrillar framework filled with metallic Li, which maintains its initial structure at 325 °C in Ar atmosphere without leakage of the liquid Li. The capillary force caused by the porous structure of the Li₄ B₅ fibrillar framework, together with its lithiophilic surface, restricts the leakage of liquid metallic Li and enables good thermal tolerance of the Li₅ B₄ /Li composite. Thus, it can be facilely operated for rechargeable high-temperature Li metal batteries. Li₅ B₄ /Li electrodes are coupled with a garnet-type ceramic electrolyte (Li_6.5 La₃ Zr_0.5 Ta_1.5 O₁₂ ) to fabricate symmetric cells, which exhibit stable Li stripping/plating behaviors with low overpotential of ≈6 mV at 200 °C using a regular sandwich-type cell configuration. This work affords new insights into realizing a stable Li metal anode for high-temperature Li metal batteries with a simple battery configuration and high safety, which is different from traditional molten-salt Li metal batteries using a pristine metallic Li anode.

Interface engineering of Co3O4 nanowire arrays with ultrafine NiO nanowires for high-performance rechargeable alkaline batteries

Interface engineering multi-component core-shell nanostructures with highly efficient and reversible faradaic reactions for energy conversion storage devices is still a challenge. Here, Co₃O₄ nanowires@NiO ultrafine nanowires on Ni foam were well fabricated via coating the NiO ultrafine nanowires on porous Co₃O₄ nanowire arrays. The combination of structural and compositional advantages endows the Co₃O₄@NiO core-shell composites with excellent electrochemical performance, such as a favorable specific capacity of 0.71 mA h cm^-2 at 3 mA cm^-2, excellent rate capability and 85% retention rate up to 10,000 cycles. Rechargeable alkaline batteries with the Co₃O₄@NiO core-shell composites and AC as cathode and anode, respectively, had a high specific capacity of 0.51 mA h cm^-2 and stable cycling ability (81% retention after 5000 cycles). The hierarchical core-shell heterostructure electrode exhibits excellent electrochemical performance, making it a very promising material for next-generation energy storage device applications.

Solvent-Free Method Prepared a Sandwich-like Nanofibrous Membrane-Reinforced Polymer Electrolyte for High-Performance All-Solid-State Lithium Batteries

Solid polymer electrolytes (SPEs) with the advantages of high safety, low volatility, and the ability to suppress Li dendrites are highly desirable to be used in next generation high-safety and high-energy lithium-ion batteries. The exploration of SPEs with superior comprehensive properties has received extensive attention for high-performance all-solid-state batteries (ASSBs). Herein, a sandwich-like nanofibrous membrane-reinforced poly-caprolaclone diol and trimethyl phosphate (TMP) composite polymer electrolyte (CPE) has been designed by a facile "solvent-free" solution-casting method. Specifically, the flame-retardant TMP is employed as a plasticizer, which can improve the ionic conductivity effectively. The as-prepared solid electrolyte exhibits superior comprehensive performance in terms of high ionic conductivity, wide electrochemical window, good compatibility with lithium metal, and superior thermal stability. Furthermore, the assembled Li//LiFePO₄ ASSBs with this solid CPE show outstanding cycling stability and high average discharge capacity at room temperature (30 °C). Undoubtedly, our study provides a new facile method and a qualified solid electrolyte material for next generation high-performance ASSBs.