A New Polymer Donor Enables Binary All-Polymer Organic Photovoltaic Cells with 18% Efficiency and Excellent Mechanical Robustness

A Fluorinated Imide-Functionalized Arene Enabling a Wide Bandgap Polymer Donor for Record-Efficiency All-Polymer Solar Cells

All-polymer solar cells (all-PSCs) present compelling advantages for commercial applications, including mechanical durability and optical and thermal stability. However, progress in developing high-performance polymer donors has trailed behind the emergence of excellent polymer acceptors. In this study, we report a new electron-deficient arene, fluorinated bithiophene imide (F-BTI) and its polymer donor SA1, in which two fluorine atoms are introduced at the outer β-positions in the thiophene rings of BTI to fine-tune the energy levels and aggregation of the resulting polymers. SA1 exhibits a deep HOMO level of -5.51 eV, a wide bandgap of 1.81 eV and suitable miscibility with the polymer acceptor. Polymer chains incorporating F-BTI result in a highly ordered π-π stacking and favorable phase-separated morphology within the all-polymer active layer. Thus, SA1 : PY-IT-based all-PSCs exhibit an efficiency of 16.31 % with excellent stability, which is further enhanced to a record value of 19.33 % (certified: 19.17 %) by constructing ternary device. This work demonstrates that F-BTI offers an effective route for developing new polymer materials with improved optoelectronic properties, and the emergence of F-BTI will change the scenario in terms of developing polymer donor for high-performance and stable all-PSCs.

Boosting organic solar cell efficiency via tailored end-group modifications of novel non-fused ring electron acceptors

In this study, we designed and synthesized two NFREAs, 2BTh-3F and 2BTh-CN, incorporating distinct substituents to modulate their electron-withdrawing properties. We meticulously explore the distinct impacts of these substituents on NFREA performance. Our investigation revealed that the introduction of 3,5-difluoro-4-cyanophenyl in 2BTh-CN significantly enhanced electron withdrawal and intramolecular charge transfer, leading to a red-shifted absorption spectrum and optimized energy levels. Consequently, organic solar cells (OSCs) utilizing 2BTh-CN demonstrate a notable power conversion efficiency (PCE) of 15.07%, outperforming those employing 2BTh-3F (PCE of 9.34%). Moreover, by incorporating 2BTh-CN into the D18:2BTh-C2 system as a third component, we achieve a PCE exceeding 17% in a high-performing ternary OSC, ranking among the most efficient NFREA-based OSCs reported to date. Overall, our study underscores the potential of deliberate design and optimization of non-fused ring acceptor molecular structures to attain outstanding photovoltaic performance.

Giant dimeric donors for all-giant-oligomer organic solar cells with efficiency over 16% and superior photostability

Increasing the molecular weight while maintaining mono-dispersity has been proved crucial in innovating high-performance photovoltaic materials in giant oligomeric acceptors. However, developing efficient giant oligomeric donors to replace the batch-varied polymers remains challenging due to a lack of design principles. Here, by designing two unique isomeric rhodanine-based linkers, we successfully regulate the assembly behaviors of giant dimeric donors (G-Dimer-Ds) and fabricate the first all-giant-oligomer OSCs pairing with giant dimeric acceptor DY. Multiple characterizations demonstrate the small homo-molecular interaction with strong thermal-driven assembly capability in G-Dimer-D2 simultaneously facilitates reducing energetic disorder, improving charge transport and obtaining stable morphology, resulting in a satisfactory efficiency of 15.70% and long-term photostability with an extrapolated T80 of ca.10,000 hours, and further enhancing thermal-driven assembly promotes efficiency of 16.05%. Our results provide construction approaches on efficient giant donors, and propose a promising type of OSC with completely definite structures, high efficiency and superior stability.

Non-Fused Star-Shape Giant Trimer Electron Acceptors for Organic Solar Cells with Efficiency over 19

Organic solar cells (OSCs) based on giant molecular acceptors (GMAs) have attracted extensive attention due to their excellent power conversion efficiency (PCE) and operation stability. However, the large conjugated plane of GMAs poses great challenges in regulating the solubility, over-size aggregation and yield, which in turn further constrains their development in commercial products. Herein, we employ a non-fused skeleton strategy to develop novel non-fused star-shape trimers (3BTT6F and 3BTT6Cl) for improving device performance. Single-bond linkage can break the rigid planarity to form a 3D architecture, generating multidimensional charge transfer pathways. Importantly, the non-fused skeleton strategy can not only significantly improve solubility and synthesis yield, but also effectively suppress molecular excessive aggregation. Consequently, due to the optimized film-forming process and charge dynamics, 3BTT6F-based binary device obtains a high PCE of 17.52 %, which is significantly higher than the reported fully fused trimers. Excitingly, 3BTT6F-based ternary device even obtains a top-level PCE of 19.26 %. Furthermore, the non-fused star-shape configuration also endows these acceptors with enhanced intermolecular interaction in the active layer, demonstrating excellent operational stability. Our work emphasizes the potential of non-fused star-shape trimers, providing a new pathway for achieving highly efficient and stable OSCs.

Advances in Stretchable Organic Photovoltaics: Flexible Transparent Electrodes and Deformable Active Layer Design

Stretchable organic photovoltaics (OPVs) have attracted significant attention as promising power sources for wearable electronic systems owing to their superior robustness under repetitive tensile strains and their good compatibility. However, reconciling a high power-conversion efficiency and a reasonable flexibility is a tremendous challenge. In addition, the development of stretchable OPVs must be accelerated to satisfy the increasing requirements of niche markets for mechanical robustness. Stretchable OPV devices can be classified as either structurally or intrinsically stretchable. This work reviews recent advances in stretchable OPVs, including the design of mechanically robust transparent electrodes, photovoltaic materials, and devices. Initially, an overview of the characteristics and recent research progress in the areas of structurally and intrinsically stretchable OPVs is provided. Subsequently, research into flexible and stretchable transparent electrodes that directly affect the performances of stretchable OPVs is summarized and analyzed. Overall, this review aims to provide an in-depth understanding of the intrinsic properties of highly efficient and deformable active materials, while also emphasizing advanced strategies for simultaneously improving the photovoltaic performance and mechanical flexibility of the active layer, including material design, multi-component settings, and structural optimization.

Optimizing Double-Fibril Network Morphology via Solid Additive Strategy Enables Binary All-Polymer Solar Cells with 19.50% Efficiency

Double-fibril network morphology (DFNM), in which the donor and the acceptor can self-assemble into a double-fibril structure, is beneficial for exciton dissociation and charge transport in organic solar cells. Herein, it is demonstrated that such DFNM can be constructed and optimized in all-polymer solar cells (all-PSCs) with the assistance of 2-alkoxynaphthalene volatile solid additives. It is revealed that the incorporation of 2-alkoxynaphthalene can induce a stepwise regulation in the aggregation of donor and acceptor molecules during film casting and thermal annealing processes. Through altering the alkoxy of 2-alkoxynaphthalene solid additives, both the intermolecular interactions and molecular miscibility with the host materials can be precisely tuned, which allows for the optimization of the molecular aggregation process and facilitation of molecular self-assembly, and thus leading to reinforced molecular packing and optimized DFNM. As a result, an unprecedented efficiency of 19.50% (certified as 19.1%) is obtained for 2-ethoxynaphthalene-processed PM6:PY-DT-X all-PSCs with excellent photostability (T80 = 1750 h). This work reveals that the optimization of DFNM via solid additive strategy is a promising avenue to boosting the performance of all-PSCs.

Conjugation-Broken Dimer Acceptors Enable High-Efficiency, Stable, and Flexibility-Robust Organic Solar Cells

Dimer acceptors in organic solar cells (OSCs) offer distinct advantages, including a well-defined molecular structure and excellent batch-to-batch reproducibility. Their high glass transition temperature (Tg) aids in achieving an optimal kinetic morphology, thereby enhancing device stability. Currently, most of dimer acceptor materials are linked with conjugated units in order to obtain high power conversion efficiencies (PCEs). In this study, different from previous works on conjugation-linked dimer acceptors, a novel series of dimer acceptors are synthesized (named T1, T4, T6, and T12), each linked with different flexible alkyl linkers, and investigated their PCEs, device stability, and flexibility robustness. When blended with PM6, the T6-based device achieves a PCE of 17.09%, comparable to the fully conjugated T0-based device's PCE of 17.12%. The molecular dynamics simulations and density functional theory calculations suggested that flexible conjugation-broken linkers (FCBLs) promote intermolecular electronic couplings, thereby maintaining good electron mobilities of dimer acceptors. Notably, the T6-based device exhibits impressive long-term stability with a T80 lifetime of 1427 h, while in the T0-based device, T80 is only 350 h. The present work has thus established the relationship between the length of flexible alkyl linkers in such dimer acceptors and the performance and stability of OSCs, which is important to further designing new materials for the fabrication of efficient and stable OSCs.

Multi-component Copolymerized Donors enable Frozen Nano-morphology and Superior Ductility for Efficient Binary Organic Solar Cells

Multi-component copolymerized donors (MCDs) have gained significant interest and have been rapidly developed in flexible organic solar cells (f-OSCs) in recent years. However, ensuring the power conversion efficiency (PCE) of f-OSCs while retaining ideal mechanical properties remains an enormous challenge. The fracture strain (FS) value of typical high-efficiency blend films is generally less than 8 %, which is far from the application standards of wearable photovoltaic devices. Therefore, we developed a series of novel MCDs after meticulous molecular design. Among them, the consistent MCD backbone and end-capped functional group formed a highly conjugated molecular plane, and the solubilization and mechanical properties were effectively optimized by modifying the proportion of solubilized alkyl chains. Consequently, due to the formation of entangled structures with a frozen blend film morphology considerably improved the high ductility of the active layer, P10.8/P20.2-TCl exhibited efficient PCE in rigid (18.53 %) and flexible (17.03 %) OSCs, along with excellent FS values (16.59 %) in pristine films, meanwhile, the outstanding FS values of 25.18 % and 12.3 % were achieved by P10.6/P20.4-TCl -based pristine and blend films, respectively, which were one of the highest records achieved by end-capped MCD-based binary OSCs, demonstrating promising application to synchronize the realization of high-efficiency and mechanically ductile flexible OSCs.

Sequential Cascade Doping of Conjugated-Polymer-Wrapped Carbon Nanotubes for Highly Electrically Conductive Platforms

To explore a highly conductive flexible platform, this study develops PIDF-BT@SWCNT by wrapping single-walled carbon nanotubes (SWCNTs) with a conjugated polymer, PIDF-BT, known for its effective doping properties. By evaluating the doping behaviors of various dopants on PIDF-BT, appropriate dopant combinations for cascade doping are selected to improve the doping efficiency of PIDF-BT@SWCNT. Specifically, using F4TCNQ or F6TCNNQ as the first dopant, followed by AuCl3 as the second dopant, demonstrates remarkable doping efficiency, surpassing that of the individual dopants and yielding an exceptional electrical conductivity exceeding 6000 S/cm. Characterization using X-ray photoelectron spectroscopy and Raman spectroscopy elucidates the doping mechanism, revealing an increase in the proportion of electron-donating atoms and the ratio of quinoid structures upon F4TCNQ/AuCl3 cascade doping. These findings offer insights into optimizing dopant combinations for cascade doping, showcasing its advantages in enhancing doping efficiency and resulting electrical conductivity compared with single dopant processes.

Morphological Homogeneity and Interface Modification as Determinant Factors of the Efficiency and Stability for Upscaling Organic Solar Cell

Morphological homogeneity and interfacial traps are essential issues to achieve high-efficiency and stable large-area organic solar cells (OSCs). Herein, by the investigation of three quinoxaline-based acceptors, i.e., PM6:Qx-1, PM6:Qx-2, and PM6:Qx-p-4Cl, the performance degradation in up-scaling OSCs is explored. The inhomogeneous morphology in PM6:Qx-2 induces a nonuniform spatial distribution of charge generation, showing a rapid decline in efficiency and stability in large-area OSCs. In comparison, the homogeneous morphology in PM6:Qx-1 and PM6:Qx-p-4Cl alleviates the stability drop. When utilizing 2-phenylethylmercaptan to fill the interfacial traps, the stability drop disappears for PM6:Qx-1 and PM6:Qx-p-4Cl, while it persists for PM6:Qx-2. The PM6:Qx-1 large-are device yields a high efficiency of 13.47% and superior thermal stability (T80 = 2888 h). Consequently, the interface modification dominates the performance degradation of large-area devices with homogeneous morphology, while it cannot eliminate the traps in inhomogeneous film. These results provide a clear understanding of degradation mechanisms in upscaling devices.

Green Printing for Scalable Organic Photovoltaic Modules by Controlling the Gradient Marangoni Flow

Despite the rapid development in the performances of organic solar cells (OSCs), high-performance OSC modules based on green printing are still limited. The severe Coffee-ring effect (CRE) is considered to be the primary reason for the nonuniform distribution of active layer films. To solve this key printing problem, the cosolvent strategy is presented to deposit the active layer films. The guest solvent Mesitylene with a higher boiling point and a lower surface tension is incorporated into the host solvent o-XY to optimize the rheological properties, such as surface tension and viscosity of the active layer solutions. And the synergistic effect of inward Marangoni flow generation and solution thickening caused by the cosolvent strategy can effectively restrain CRE, resulting in highly homogeneous large-area active layer films. In addition, the optimized crystallization and phase separation of active layer films effectively accelerate the charge transport and exciton dissociation of devices. Consequently, based on PM6:BTP-eC9 system, the device prepared with the co-solvent strategy shows the a power conversion efficiency of 17.80%. Moreover, as the effective area scales to 1 and 16.94 cm2, the recorded performances are altered to 16.71% and 14.58%. This study provides a universal pathway for the development of green-printed high-efficiency organic photovoltaics.

Isomerization of Benzothiadiazole Yields a Promising Polymer Donor and Organic Solar Cells with Efficiency of 19.0

The exploration of high-performance and low-cost wide-bandgap polymer donors remains critical to achieve high-efficiency nonfullerene organic solar cells (OSCs) beyond current thresholds. Herein, the 1,2,3-benzothiadiazole (iBT), which is an isomer of 2,1,3-benzothiadiazole (BT), is used to design wide-bandgap polymer donor PiBT. The PiBT-based solar cells reach efficiency of 19.0%, which is one of the highest efficiencies in binary OSCs. Systemic studies show that isomerization of BT to iBT can finely regulate the polymers' photoelectric properties including i) increasing the extinction coefficient and photon harvest, ii) downshifting the highest occupied molecular orbital energy levels, iii) improving the coplanarity of polymer backbones, iv) offering good thermodynamic miscibility with acceptors. Consequently, the PiBT:Y6 bulk heterojunction (BHJ) device simultaneously reaches advantageous nanoscale morphology, efficient exciton generation and dissociation, fast charge transportation, and suppressed charge recombination, leading to larger VOC of 0.87 V, higher JSC of 28.2 mA cm-2, greater fill factor of 77.3%, and thus higher efficiency of 19.0%, while the analog-PBT-based OSCs reach efficiency of only 12.9%. Moreover, the key intermediate iBT can be easily afforded from industry chemicals via two-step procedure. Overall, this contribution highlights that iBT is a promising motif for designing high-performance polymer donors.

Impact of Electrostatic Interaction on Vertical Morphology and Energy Loss in Efficient Pseudo-Planar Heterojunction Organic Solar Cells

Although a suitable vertical phase separation (VPS) morphology is essential for improving charge transport efficiency, reducing charge recombination, and ultimately boosting the efficiency of organic solar cells (OSCs), there is a lack of theoretical guidance on how to achieve the ideal morphology. Herein, a relationship between the molecular structure and the VPS morphology of pseudo-planar heterojunction (PPHJ) OSCs is established by using molecular surface electrostatic potential (ESP) as a bridge. The morphological evolution mechanism is revealed by studying four binary systems with vary electrostatic potential difference (∆ESP) between donors (Ds) and acceptors (As). The findings manifest that as ∆ESP increases, the active layer is more likely to form a well-mixed phase, while a smaller ∆ESP favors VPS morphology. Interestingly, it is also observed that a larger ∆ESP leads to enhanced miscibility between Ds and As, resulting in higher non-radiative energy losses (ΔE3). Based on these discoveries, a ternary PPHJ device is meticulously designed with an appropriate ∆ESP to obtain better VPS morphology and lower ΔE3, and an impressive efficiency of 19.09% is achieved. This work demonstrates that by optimizing the ΔESP, not only the formation of VPS morphology can be controlled, but also energy losses can be reduced, paving the way to further boost OSC performance.

Stability of organic solar cells: toward commercial applications

Organic solar cells (OSCs) have attracted a great deal of attention in the field of clean solar energy due to their advantages of transparency, flexibility, low cost and light weight. Introducing them to the market enables seamless integration into buildings and windows, while also supporting wearable, portable electronics and internet-of-things (IoT) devices. With the development of photovoltaic materials and the optimization of fabrication technology, the power conversion efficiencies (PCEs) of OSCs have rapidly improved and now exceed 20%. However, there is a significant lack of focus on material stability and device lifetime, causing a severe hindrance to commercial applications. In this review, we carefully review important strategies employed to improve the stability of OSCs over the past three years from the perspectives of material design and device engineering. Furthermore, we analyze and discuss the current important progress in terms of air, light, thermal and mechanical stability. Finally, we propose the future research directions to overcome the challenges in achieving highly stable OSCs. We expect that this review will contribute to solving the stability problem of OSCs, eventually paving the way for commercial applications in the near future.

Binary All-polymer Solar Cells with a Perhalogenated-Thiophene-Based Solid Additive Surpass 18 % Efficiency

Morphological control of all-polymer blends is quintessential yet challenging in fabricating high-performance organic solar cells. Recently, solid additives (SAs) have been approved to be capable in tuning the morphology of polymer: small-molecule blends improving the performance and stability of devices. Herein, three perhalogenated thiophenes, which are 3,4-dibromo-2,5-diiodothiophene (SA-T1), 2,5-dibromo-3,4-diiodothiophene (SA-T2), and 2,3-dibromo-4,5-diiodothiophene (SA-T3), were adopted as SAs to optimize the performance of all-polymer organic solar cells (APSCs). For the blend of PM6 and PY-IT, benefitting from the intermolecular interactions between perhalogenated thiophenes and polymers, the molecular packing properties could be finely regulated after introducing these SAs. In situ UV/Vis measurement revealed that these SAs could assist morphological character evolution in the all-polymer blend, leading to their optimal morphologies. Compared to the as-cast device of PM6 : PY-IT, all SA-treated binary devices displayed enhanced power conversion efficiencies of 17.4-18.3 % with obviously elevated short-circuit current densities and fill factors. To our knowledge, the PCE of 18.3 % for SA-T1-treated binary ranks the highest among all binary APSCs to date. Meanwhile, the universality of SA-T1 in other all-polymer blends is demonstrated with unanimously improved device performance. This work provide a new pathway in realizing high-performance APSCs.

The role of interfacial donor-acceptor percolation in efficient and stable all-polymer solar cells

Polymerization of Y6-type acceptor molecules leads to bulk-heterojunction organic solar cells with both high power-conversion efficiency and device stability, but the underlying mechanism remains unclear. Here we show that the exciton recombination dynamics of polymerized Y6-type acceptors (Y6-PAs) strongly depends on the degree of aggregation. While the fast exciton recombination rate in aggregated Y6-PA competes with electron-hole separation at the donor-acceptor (D-A) interface, the much-suppressed exciton recombination rate in dispersed Y6-PA is sufficient to allow efficient free charge generation. Indeed, our experimental results and theoretical simulations reveal that Y6-PAs have larger miscibility with the donor polymer than Y6-type small molecular acceptors, leading to D-A percolation that effectively prevents the formation of Y6-PA aggregates at the interface. Besides enabling high charge generation efficiency, the interfacial D-A percolation also improves the thermodynamic stability of the blend morphology, as evident by the reduced device "burn-in" loss upon solar illumination.

Achieving Record-High Stretchability and Mechanical Stability in Organic Photovoltaic Blends with a Dilute-absorber Strategy

Organic solar cells (OSCs) have potential for applications in wearable electronics. Except for high power conversion efficiency (PCE), excellent tensile properties and mechanical stability are required for achieving high-performance wearable OSCs, while the present metrics barely meet the stretchable requirements. Herein, this work proposes a facile and low-cost strategy for constructing intrinsically stretchable OSCs by introducing a readily accessible polymer elastomer as a diluent for all-polymer photovoltaic blends. Remarkably, record-high stretchability with a fracture strain of up to 1000% and mechanical stability with elastic recovery >90% under cyclic tensile tests are realized in the OSCs active layers for the first time. Specifically, the tensile properties of best-performing all-polymer photovoltaic blends are increased by up to 250 times after blending. Previously unattainable performance metrics (fracture strain >50% and PCE >10%) are achieved simultaneously for the resulting photovoltaic films. Furthermore, an overall evaluation parameter y is proposed for the efficiency-cost- stretchability balance of photovoltaic blend films. The y value of dilute-absorber system is two orders of magnitude greater than those of prior state-of-the-art systems. Additionally, intrinsically stretchable devices are prepared to showcase the mechanical stability. Overall, this work offers a new avenue for constructing and comprehensively evaluating intrinsically stretchable organic electronic films.

Structure-Activity Relationship between Crystallinity and Carrier Transport of Two-Dimensional Donor Units in Organic Solar Cells

Benzo[1,2-b:4,5-b']dithiophene (BDT) and its derivatives have made important contributions to constructing high-performance polymers. However, it is difficult to clarify the real role of donor units due to the interference of strong electronegativity and crystallinity of acceptor units in the D-A copolymer. Here, we design a cyclohexane-substituted dithieno[3,2-f:2',3'-h]quinoxaline (DTQ)-based acceptor unit with successfully destroyed crystallinity and charge transport. Three donor-dominated materials PQH-BTF, PQH-BTCl, and PQH-BFCl are obtained. It is found that the materials exhibit obvious differences after destroying the crystallization and charge transport of the acceptor unit, and the real role of different two-dimensional donor units in designed polymers is confirmed. The backbone BDF exhibits much stronger intermolecular interactions compared to BDT, while the side chain ThF demonstrates a higher crystallization capacity than that of ThCl. More interestingly, it can be inferred that the molecular backbone is likely to construct miscible-phase crystallization (D-A crystal) while the side chain tends to demonstrate a capacity for pure-phase crystallization (D-D crystal) in a 2D donor system. Different crystallization leads to different exciton transport: pure-phase crystallization is conducive to the reduction of trap-assisted recombination, while miscible crystallization is beneficial to the reduction of bimolecular recombination. This work can help to choose donor units more accurately when preparing D-A copolymers.

Thickness Tolerance in Large-Area Organic Photovoltaics with Fluorine-Substituted Regioregular Conjugated Polymer

Large areas and simple processing methods are necessary for the commercialization of organic photovoltaics (OPVs). However, the efficiency drop due to the variation in thickness of OPVs limits their large-scale applications. Regioregular polymers with good crystallinity and packing properties that exhibit high charge mobility and extraction ability can help overcome these limitations. In this study, a regioregular polymer named PDBD-2FBT was synthesized. The crystallinity and packing properties of PDBD-2FBT were enhanced by a simple thermal treatment. Using PDBD-2FBT material as a donor and Y6-HU as an acceptor, we fabricated binary blend OPV devices. The devices with optimized active layer thickness achieved a power conversion efficiency (PCE) of 14.14%. A PCE of 13.18% was maintained even in thick-film conditions (400 nm), and thickness tolerance was observed. Based on the thickness tolerance, a 5-line module measuring 36 cm2 was fabricated via the bar-coating method, and a PCE of approximately 10% was achieved.

Regulating Phase Separation Kinetics for High-Efficiency and Mechanically Robust All-Polymer Solar Cells

All-polymer solar cells (all-PSCs) possess excellent operation stability and mechanical robustness than other types of organic solar cells, thereby attracting considerable attention for wearable flexible electron devices. However, the power conversion efficiencies (PCEs) of all-PSCs are still lagging behind those of small-molecule-acceptor-based systems owing to the limitation of photoactive materials and unsatisfactory blend morphology. In this work, a novel terpolymer, denoted as PBDB-TFCl (poly4,8-bis(5-(2-ethylhexyl)-4-fluorothiophen-2-yl)benzo[1,2-b:4,5-b″]dithiophene-1,3-bis(2-ethylhexyl)-5,7-di(thiophen-2-yl)-4H,8H-benzo[1,2-c:4,5-c″]dithiophene-4,8-dione-4,8-bis(4-chloro-5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b:4,5-b']dithiophene), is used as an electron donor coupled with a ternary strategy to optimize the performance of all-PSCs. The addition of PBDB-TCl unit deepens the highest occupied molecular orbital energy level, reducing voltage losses. Moreover, the introduction of the guest donor (D18-Cl) effectively regulates the phase-transition kinetics of PBDB-TFCl:D18-Cl:PY-IT during the film formation, leading to ideal size of aggregations and enhanced crystallinity. PBDB-TFCl:D18-Cl:PY-IT devices exhibit a PCE of 18.6% (certified as 18.3%), judged as the highest value so far obtained with all-PSCs. Besides, based on the ternary active layer, the manufactured 36 cm2 flexible modules exhibit a PCE of 15.1%. Meanwhile, the ternary PSCs exhibit superior photostability and mechanical stability. In summary, the proposed strategy, based on molecular design and the ternary strategy, allows optimization of the all-polymer blend morphology and improvement of the photovoltaic performance for stable large-scale flexible PSCs.

18.6% Efficiency All-Polymer Solar Cells Enabled by a Wide Bandgap Polymer Donor Based on Benzo[1,2-d:4,5-d']bisthiazole

The limited selection of wide bandgap polymer donors for all-polymer solar cells (all-PSCs) is a bottleneck problem restricting their further development and remains poorly studied. Herein, a new wide bandgap polymer, namely PBBTz-Cl, is designed and synthesized by bridging the benzobisthiazole acceptor block and chlorinated benzodithiophene donor block with thiophene units for application as an electron donor in all-PSCs. PBBTz-Cl not only possesses wide bandgap and deep energy levels but also displays strong absorption, high-planar structure, and good crystallinity, making it a promising candidate for application as a polymer donor in organic solar cells. When paired with the narrow bandgap polymer acceptor PY-IT, a fibril-like morphology forms, which facilitates exciton dissociation and charge transport, contributing to a power conversion efficiency (PCE) of 17.15% of the corresponding all-PSCs. Moreover, when introducing another crystalline polymer acceptor BTP-2T2F into the PBBTz-Cl:PY-IT host blend, the absorption ditch in the range of 600-750 nm is filled, and the blend morphology is further optimized with the trap density reducing. As a result, the ternary blend all-PSCs achieve a significantly improved PCE of 18.60%, which is among the highest values for all-PSCs to date.

Delayed Crystallization Kinetics Allowing High-Efficiency All-Polymer Photovoltaics with Superior Upscaled Manufacturing

Though encouraging performance is achieved in small-area organic photovoltaics (OPVs), reducing efficiency loss when evoluted to large-area modules is an important but unsolved issue. Considering that polymer materials show benefits in film-forming processability and mechanical robustness, a high-efficiency all-polymer OPV module is demonstrated in this work. First, a ternary blend consisting of two polymer donors, PM6 and PBQx-TCl, and one polymer acceptor, PY-IT, is developed, with which triplet state recombination is suppressed for a reduced energy loss, thus allowing a higher voltage; and donor-acceptor miscibility is compromised for enhanced charge transport, thus resulting in improved photocurrent and fill factor; all these contribute to a champion efficiency of 19% for all-polymer OPVs. Second, the delayed crystallization kinetics from solution to film solidification is achieved that gives a longer operation time window for optimized blend morphology in large-area module, thus relieving the loss of fill factor and allowing a record efficiency of 16.26% on an upscaled module with an area of 19.3 cm2 . Besides, this all-polymer system also shows excellent mechanical stability. This work demonstrates that all-polymer ternary systems are capable of solving the upscaled manufacturing issue, thereby enabling high-efficiency OPV modules.

Processability Considerations for Next-Generation Organic Photovoltaic Materials

The evolution of organic semiconductors for organic photovoltaics (OPVs) has resulted in unforeseen outcomes. This has provided substitute choices of photoactive layer materials, which effectively convert sunlight into electricity. Recently developed OPV materials have narrowed down the gaps in efficiency, stability, and cost in devices. Records now show power conversion efficiency in single-junction devices closing to 20%. Despite this, there is still a gap between the currently developed OPV materials and those that meet the requirements of practical applications, especially the solution processability issue widely concerned in the field of OPVs. Based on the general rule that structure determines properties, methodologies to enhance the processability of OPV materials are reviewed and explored from the perspective of material design and views on the further development of processable OPV materials are presented. Considering the current dilemma that the existing evaluation indicators cannot reflect the industrial processability of OPV materials, a more complete set of key performance indicators are proposed for their processability considerations. The purpose of this perspective is to raise awareness of the boundary conditions that exist in industrial OPV manufacturing and to provide guidance for academic research that aspires to contribute to technological advancements.

Central Core Substitutions and Film-Formation Process Optimization Enable Approaching 19% Efficiency All-Polymer Solar Cells

Molecular interactions and film-formation processes greatly impact the blend film morphology and device performances of all-polymer solar cells (all-PSCs). Molecular structure, such as the central cores of polymer acceptors, would significantly influence this process. Herein, the central core substitutions of polymer acceptors are adjusted and three quinoxaline (Qx)-fused-core-based materials, PQx1, PQx2, and PQx3 are synthesized. The molecular aggregation ability and intermolecular interaction are systematically regulated, which subsequently influence the film-formation process and determine the resulting blend film morphology. As a result, PQx3, with favorable aggregation ability and moderate interaction with polymer donor PM6, achieves efficient all-PSCs with a high power conversion efficiency (PCE) of 17.60%, which could be further improved to 18.06% after carefully optimizing device annealing and interface layer. This impressive PCE is one of the highest values for binary all-PSCs based on the classical polymer donor PM6. PYF-T-o is also involved in promoting light utilization, and the resulting ternary device shows an impressive PCE of 18.82%. In addition, PM6:PQx3-based devices exhibit high film-thickness tolerance, superior stability, and considerable potential for large-scale devices (16.23% in 1 cm2 device). These results highlight the importance of structure optimization of polymer acceptors and film-formation process control for obtaining efficient and stable all-PSCs.

On the Conformation of Dimeric Acceptors and Their Polymer Solar Cells with Efficiency over 18

The determination of molecular conformations of oligomeric acceptors (OAs) and their impact on molecular packing are crucial for understanding the photovoltaic performance of their resulting polymer solar cells (PSCs) but have not been well studied yet. Herein, we synthesized two dimeric acceptor materials, DIBP3F-Se and DIBP3F-S, which bridged two segments of Y6-derivatives by selenophene and thiophene, respectively. Theoretical simulation and experimental 1D and 2D NMR spectroscopic studies prove that both dimers exhibit O-shaped conformations other than S- or U-shaped counter-ones. Notably, this O-shaped conformation is likely governed by a distinctive "conformational lock" mechanism, arising from the intensified intramolecular π-π interactions among their two terminal groups within the dimers. PSCs based on DIBP3F-Se deliver a maximum efficiency of 18.09 %, outperforming DIBP3F-S-based cells (16.11 %) and ranking among the highest efficiencies for OA-based PSCs. This work demonstrates a facile method to obtain OA conformations and highlights the potential of dimeric acceptors for high-performance PSCs.

Improving Photovoltaic Performance of All-Polymer Solar Cells by Adding an Amorphous B←N Embedded Polymer as the Third Component

Currently, most of the disclosed ternary strategies to improve photovoltaic performance of all-polymer solar cells (all-PSCs) commonly focus on the guest polymers having similar structures with the host polymer donors or acceptors. Herein, this work develops a distinctive ternary method that adding an amorphous B←N embedded polymer named BN-Cl-2fT to a crystallized host polymer blend of PM6 (a commercialized polymer donor) and PY-TT (a copolymer of Y6 and thieno[3,2-b]thiophene). Although the structures between BN-Cl-2fT and PM6 and PY-TT are completely different, excellent miscibility is found between BN-Cl-2fT and both of the host PM6 and PY-TT, which can be interpreted by the crowded phenyl groups anchoring along the backbone of BN-Cl-2fT, leading to weak self-aggregation. Glazing incidence wide-angle X-ray diffraction (GIWAXS) measurements explicitly confirm the crystallization of PM6 and PY-TT and amorphous feature of BN-Cl-2fT. Furthermore, adding 10 wt% BN-Cl-2fT to PM6:PY-TT can significantly enhance the crystallization of the host polymers. Thus the ternary devices based on PM6:PY-TT:BN-Cl-2fT afford promote short-circuit current density (JSC , 23.29 vs. 21.80 mA cm-2 ), fill factor (FF, 62.4% vs. 60.0%), and power conversion efficiency (PCE, 13.70% vs. 12.23%) in contrast to these parameters of binary devices based on PM6:PY-TT. This work provides a unique and enlightening avenue to design high performance all-PSCs by adding amorphous B←N embedded polymers as guest component to enhance host-crystallization.

Achieved 18.9% Efficiency by Fine-Tuning Non-Fullerene Acceptor Content to Simultaneously Increase the Short-Circuit Current and Fill Factor of Organic Solar Cells

In this study, using PM6:L8-BO as the main system and non-fullerene acceptor IDIC as the third component, a series of ternary organic solar cells (TOSCs) are fabricated. The results reveal that IDIC plays a significant role in enhancing the performance of TOSCs by optimizing the morphology of blended films and forming interpenetrating nanostructure. The improved film morphology facilitates exciton dissociation and collection in TOSCs, which causes an increase in the short-circuit current density (JSC ) and fill factor (FF). Further, by optimizing the IDIC content, the power conversion efficiency (PCE) of TOSCs reaches 18.9%. Besides, the prepared TOSCs exhibit a JSC of 27.51 mA cm-2 and FF of 76.64%, which are much higher than those of PM6:L8-BO-based organic solar cells (OSCs). Furthermore, the addition of IDIC improves the long-term stability of the OSCs. Meanwhile, TOSCs with a large effective area of 1.00 cm2 have been prepared, which exhibit a PCE of 12.4%. These findings suggest that modifying the amount of the third component can be a useful strategy to construct hight-efficiency TOSCs with practical application potential.

Modular-Approach Synthesis of Giant Molecule Acceptors via Lewis-Acid-Catalyzed Knoevenagel Condensation for Stable Polymer Solar Cells

The operational stability of polymer solar cells is a critical concern with respect to the thermodynamic relaxation of acceptor-donor-acceptor (A-D-A) or A-DA'D-A structured small-molecule acceptors (SMAs) within their blends with polymer donors. Giant molecule acceptors (GMAs) bearing SMAs as subunits offer a solution to this issue, while their classical synthesis via the Stille coupling suffers from low reaction efficiency and difficulty in obtaining mono-brominated SMA, rendering the approach impractical for their large-scale and low-cost preparation. In this study, we present a simple and cost-effective solution to this challenge through Lewis acid-catalyzed Knoevenagel condensation with boron trifluoride etherate (BF3  ⋅ OEt2 ) as catalyst. We demonstrated that the coupling of the monoaldehyde-terminated A-D-CHO unit and the methylene-based A-link-A (or its silyl enol ether counterpart) substrates can be quantitatively achieved within 30 minutes in the presence of acetic anhydride, affording a variety of GMAs connected via the flexible and conjugated linkers. The photophysical properties was fully studied, yielding a high device efficiency of over 18 %. Our findings offer a promising alternative for the modular synthesis of GMAs with high yields, easier work up, and the widespread application of such methodology will undoubtedly accelerate the progress of stable polymer solar cells.

A Wide Bandgap Acceptor with Large Dielectric Constant and High Electrostatic Potential Values for Efficient Organic Photovoltaic Cells

Low-bandgap materials have achieved rapid development and promoted the enhancement of power conversion efficiencies (PCEs) of organic photovoltaic (OPV) cells. However, the design of wide-bandgap non-fullerene acceptors (WBG-NFAs), required by indoor applications and tandem cells, has been lagging far behind the development of OPV technologies. Here, we designed and synthesized two NFAs named ITCC-Cl and TIDC-Cl by finely optimizing ITCC. In contrast with ITCC and ITCC-Cl, TIDC-Cl can maintain a wider bandgap and a higher electrostatic potential simultaneously. When blending with the donor PB2, the highest dielectric constant is also obtained in TIDC-Cl-based films, enabling efficient charge generation. Therefore, the PB2:TIDC-Cl-based cell possessed a high PCE of 13.8% with an excellent fill factor (FF) of 78.2% under the air mass 1.5G (AM 1.5G) condition. Furthermore, an exciting PCE of 27.1% can be accomplished in the PB2:TIDC-Cl system under the illumination of 500 lux (2700 K light-emitting diode). Combined with the theoretical simulation, the tandem OPV cell based on TIDC-Cl was fabricated and exhibited an excellent PCE of 20.0%.

Poly(dimethylsiloxane)-block-PM6 Polymer Donors for High-Performance and Mechanically Robust Polymer Solar Cells

High power conversion efficiency (PCE) and stretchability are the dual requirements for the wearable application of polymer solar cells (PSCs). However, most efficient photoactive films are mechanically brittle. In this work, highly efficient (PCE = 18%) and mechanically robust (crack-onset strain (COS) = 18%) PSCs are acheived by designing block copolymer (BCP) donors, PM6-b-PDMSx (x = 5k, 12k, and 19k). In these BCP donors, stretchable poly(dimethylsiloxane) (PDMS) blocks are covalently linked with the PM6 blocks to effectively increase the stretchability. The stretchability of the BCP donors increases with a longer PDMS block, and PM6-b-PDMS_19k :L8-BO PSC exhibits a high PCE (18%) and 9-times higher COS value (18%) compared to that (COS = 2%) of the PM6:L8-BO-based PSC. However, the PM6:L8-BO:PDMS_12k ternary blend shows inferior PCE (5%) and COS (1%) due to the macrophase separation between PDMS and active components. In the intrinsically stretchable PSC, the PM6-b-PDMS_19k :L8-BO blend exhibits significantly greater mechanical stability PCE_80% ((80% of the initial PCE) at 36% strain) than those of the PM6:L8-BO blend (PCE_80% at 12% strain) and the PM6:L8-BO:PDMS ternary blend (PCE_80% at 4% strain). This study suggests an effective design strategy of BCP P_D to achieve stretchable and efficient PSCs.

Geometry design of tethered small-molecule acceptor enables highly stable and efficient polymer solar cells

With the power conversion efficiency of binary polymer solar cells dramatically improved, the thermal stability of the small-molecule acceptors raised the main concerns on the device operating stability. Here, to address this issue, thiophene-dicarboxylate spacer tethered small-molecule acceptors are designed, and their molecular geometries are further regulated via the thiophene-core isomerism engineering, affording dimeric TDY-α with a 2, 5-substitution and TDY-β with 3, 4-substitution on the core. It shows that TDY-α processes a higher glass transition temperature, better crystallinity relative to its individual small-molecule acceptor segment and isomeric counterpart of TDY-β, and a more stable morphology with the polymer donor. As a result, the TDY-α based device delivers a higher device efficiency of 18.1%, and most important, achieves an extrapolated lifetime of about 35000 hours that retaining 80% of their initial efficiency. Our result suggests that with proper geometry design, the tethered small-molecule acceptors can achieve both high device efficiency and operating stability.

TCAD Device Simulation of All-Polymer Solar Cells for Indoor Applications: Potential for Tandem vs. Single Junction Cells

The utilization of indoor photovoltaics makes it feasible to harvest energy from artificial light sources. Although single-junction indoor photovoltaics have demonstrated exceptional efficacy when using LED lighting, there is still a need for more comprehensive testing of tandem structures. Herein, the first systematic TCAD simulation study on the potential for tandem all-polymer solar cells (all-PSCs) for indoor applications is provided. The presented all-PSCs are based on experimental work in which the top wide bandgap subcell comprises a polymer blend PM7:PIDT, while the bottom narrow bandgap subcell has a polymer blend PM6:PY-IT. Standalone and tandem cells are simulated under AM1.5G solar radiation, and the simulation results are compared with measurements to calibrate the physical models and material parameters revealing PCE values of 10.11%, 16.50%, and 17.58% for the front, rear, and tandem cells, respectively. Next, we assessed the performance characteristics of the three cells under a white LED environment for different color temperatures and light intensities. The results showed a superior performance of the front cell, while a deterioration in the performance was observed for the tandem cell, reflecting in a lower PCE of 16.22% at a color temperature of 2900 K. Thus, an optimized tandem for outdoor applications was not suitable for indoor conditions. In order to alleviate this issue, we propose designing the tandem for indoor lightening by an appropriate choice of thicknesses of the top and bottom absorber layers in order to achieve the current matching point. Reducing the top absorber thickness while slightly increasing the bottom thickness resulted in a higher PCE of 27.80% at 2900 K.

Electron Transport in Organic Photovoltaic Acceptor Materials: Improving the Carrier Mobilities by Intramolecular and Intermolecular Modulations

High carrier mobility is beneficial to increase the active-layer thickness while maintaining a high fill factor, which is crucial to further improve the light harvesting and organic photovoltaic efficiency. The aim of this Perspective is to elucidate the electron transport mechanisms in prototypical non-fullerene (NF) acceptors through our recent theoretical studies. The electron transport in A-D-A small-molecule acceptors (SMAs), e.g., ITIC and Y6, is mainly determined by end-group π-π stacking. Relative to ITIC, the angular backbone along with more flexible side chains leads to Y6 having a closer stacking and enhanced intermolecular electronic connectivity. For polymerized rylene diimide acceptors, to achieve high electron mobilities, they need to simultaneously increase intramolecular and intermolecular connectivity. Finally, finely tuning the π-bridge modes to enhance intramolecular superexchange coupling is essential to develop novel polymerized A-D-A SMAs.

Unveiling the Morphological and Physical Mechanism of Burn-in Loss Alleviation by Ternary Matrix Toward Stable and Efficient All-Polymer Solar Cells

All-polymer solar cells (All-PSCs) are considered the most promising candidate in achieving both efficient and stable organic photovoltaic devices, yet the field has rarely presented an in-depth understanding of corresponding device stability while efficiency is continuously boosted via the innovation of polymer acceptors. Herein, a ternary matrix is built for all-PSCs with optimized morphology, improved film ductility and importantly, boosted efficiency and better operational stability than its parental binary counterparts, as a platform to study the underlying mechanism. The target system PQM-Cl:PTQ10:PY-IT (0.8:0.2:1.2) exhibits an alleviated burn-in loss of morphology and efficiency under light soaking, which supports its promoted device lifetime. The comprehensive characterizations of fresh and light-soaked active layers lead to a clear illustration of opposite morphological and physical degradation direction of PQM-Cl and PTQ10, thus resulting in a delicate balance at the optimal ternary system. Specifically, the enlarging tendency of PQM-Cl and shrinking preference of PTQ10 in terms of phase separation leads to a stable morphology in their mixing phase; the hole transfer kinetics of PQM-Cl:PY-IT host is stabilized by incorporating PTQ10. This work succeeds in reaching a deep insight into all-PSC's stability promotion by a rational ternary design, which booms the prospect of gaining high-performance all-PSCs.

Compromising Charge Generation and Recombination of Organic Photovoltaics with Mixed Diluent Strategy for Certified 19.4% Efficiency

The ternary blend is demonstrated as an effective strategy to promote the device performance of organic photovoltaics (OPVs) due to the dilution effect. While the compromise between the charge generation and recombination remains a challenge. Here, a mixed diluent strategy for further improving the device efficiency of OPV is proposed. Specifically, the high-performance OPV system with a polymer donor, i.e., PM6, and a nonfullerene acceptor (NFA), i.e., BTP-eC9, is diluted by the mixed diluents, which involve a high bandgap NFA of BTP-S17 and a low bandgap NFA of BTP-S16 (similar with that of the BTP-eC9). The BTP-S17 of better miscibility with BTP-eC9 can dramatically enhance the open-circuit voltage (V_OC ), while the BTP-S16 maximizes the charge generation or the short-circuit current density (J_SC ). The interplay of BTP-17 and BTP-S16 enables better compromise between charge generation and recombination, thus leading to a high device performance of 19.76% (certified 19.41%), which is the best among single-junction OPVs. Further analysis on carrier dynamics validates the efficacy of mixed diluents for balancing charge generation and recombination, which can be further attributed to the more diverse energetic landscapes and improved morphology. Therefore, this work provides an effective strategy for high-performance OPV for further commercialization.

Improved photovoltaic performance and robustness of all-polymer solar cells enabled by a polyfullerene guest acceptor

Fullerene acceptors typically possess excellent electron-transporting properties and can work as guest components in ternary organic solar cells to enhance the charge extraction and efficiencies. However, conventional fullerene small molecules typically suffer from undesirable segregation and dimerization, thus limiting their applications in organic solar cells. Herein we report the use of a poly(fullerene-alt-xylene) acceptor (PFBO-C12) as guest component enables a significant efficiency increase from 16.9% for binary cells to 18.0% for ternary all-polymer solar cells. Ultrafast optic and optoelectronic studies unveil that PFBO-C12 can facilitate hole transfer and suppress charge recombination. Morphological investigations show that the ternary blends maintain a favorable morphology with high crystallinity and smaller domain size. Meanwhile, the introduction of PFBO-C12 reduces voltage loss and enables all-polymer solar cells with excellent light stability and mechanical durability in flexible devices. This work demonstrates that introducing polyfullerenes as guest components is an effective approach to achieving highly efficient ternary all-polymer solar cells with good stability and mechanical robustness.

Advances in organic photovoltaic cells: a comprehensive review of materials, technologies, and performance

This paper provides a comprehensive overview of organic photovoltaic (OPV) cells, including their materials, technologies, and performance. In this context, the historical evolution of PV cell technology is explored, and the classification of PV production technologies is presented, along with a comparative analysis of first, second, and third-generation solar cells. A classification and comparison of PV cells based on materials used is also provided. The working principles and device structures of OPV cells are examined, and a brief comparison between device structures is made, highlighting their advantages, disadvantages, and key features. The various parts of OPV cells are discussed, and their performance, efficiency, and electrical characteristics are reviewed. A detailed SWOT analysis is conducted, identifying promising strengths and opportunities, as well as challenges and threats to the technology. The paper indicates that OPV cells have the potential to revolutionize the solar energy industry due to their low production costs, and ability to produce thin, flexible solar cells. However, challenges such as lower efficiency, durability, and technological limitations still exist. Despite these challenges, the tunability and versatility of organic materials offer promise for future success. The paper concludes by suggesting that future research should focus on addressing the identified challenges and developing new materials and technologies that can further improve the performance and efficiency of OPV cells.

Proposal and Design of Flexible All-Polymer/CIGS Tandem Solar Cell

Tandem solar cells (TSCs) have attracted prodigious attention for their high efficiency, which can surmount the Shockley-Queisser limit for single-junction solar cells. Flexible TSCs are lightweight and cost-effective, and are considered a promising approach for a wide range of applications. In this paper, a numerical model, based on TCAD simulation, is presented to assess the performance of a novel two-terminal (2T) all-polymer/CIGS TSC. To confirm the model, the obtained simulation results were compared with standalone fabricated all-polymer and CIGS single solar cells. Common properties of the polymer and CIGS complementary candidates are their non-toxicity and flexibility. The initial top all-polymer solar cell had a photoactive blend layer (PM7:PIDT), the optical bandgap of which was 1.76 eV, and the initial bottom cell had a photoactive CIGS layer, with a bandgap of 1.15 eV. The simulation was then carried out on the initially connected cells, revealing a power conversion efficiency (PCE) of 16.77%. Next, some optimization techniques were applied to enhance the tandem performance. Upon treating the band alignment, the PCE became 18.57%, while the optimization of polymer and CIGS thicknesses showed the best performance, reflected by a PCE of 22.73%. Moreover, it was found that the condition of current matching did not necessarily meet the maximum PCE condition, signifying the essential role of full optoelectronic simulations. All TCAD simulations were performed via an Atlas device simulator, where the light illumination was AM1.5G. The current study can offer design strategies and effective suggestions for flexible thin-film TSCs for potential applications in wearable electronics.

Manipulating Polymer Backbone Configuration via Halogenated Asymmetric End-Groups Enables Over 18% Efficiency All-Polymer Solar Cells

High-performance all-polymer solar cells (all-PSCs) deeply rely on the joint contributions of desirable optical absorption, adaptive energy levels, and appropriate morphology. Herein, two structural analogous polymerized small-molecule acceptors (PSMAs), PYFCl-T and PYF&PYCl-T, are synthesized, and then incorporated into the PM6:PY-IT binary blends to construct ternary all-PSCs. Due to the superior compatibility of PY-IT and PYFCl-T, the ternary all-PSC based on PM6:PY-IT:PYFCl-T with 10 wt% PYFCl-T, presents higher and more balanced charge mobility, suppressed charge recombination, and faster charge-transfer kinetics, resulting in an outstanding power conversion efficiency (PCE) of 18.12% with enhanced J_sc and FF, which is much higher than that (PCE of 16.09%) of the binary all-PSCs based on PM6:PY-IT. Besides, the ternary all-PSCs also exhibit improved photostability. The conspicuous performance enhancement principally should give the credit to the miscibility-driven phase optimization of the donor and acceptor. These findings highlight the significance of polymer-backbone configuration modulation of PSMAs in morphology optimization toward boosting the device properties of all-PSCs.

BN-Bond-Embedded Triplet Terpolymers with Small Singlet-Triplet Energy Gaps for Suppressing Non-Radiative Recombination and Improving Blend Morphology in Organic Solar Cells

Suppressing the photon energy loss (E_loss ), especially the non-radiative loss, is of importance to further improve the device performance of organic solar cells (OSCs). However, typical π-conjugated semiconductors possess a large singlet-triplet energy gap (ΔE_ST ), leading to a lower triplet state than charge transfer state and contributing to a non-radiative loss channel of the photocurrent by the triplet state. Herein, a series of triplet polymer donors are developed by introducing a BNIDT block into the PM6 polymer backbone. The high electron affinity of BNIDT and the opposite resonance effect of the BN bond in BNIDT results in a lowered highest occupied molecular orbital (HOMO) and a largely reduced ΔE_ST . Moreover, the morphology of the active blends is also optimized by fine-tuning the BNIDT content. Therefore, non-radiative recombination via the terminal triplet loss channels and morphology traps is effectively suppressed. The PNB-3 (with 3% BNIDT):L8-BO device exhibits both small ΔE_ST and optimized morphology, favoring more efficient charge transfer and transport. Finally, the simultaneously enhanced V_oc of 0.907 V, J_sc of 26.59 mA cm^-2 , and FF of 78.86% contribute to a champion PCE of 19.02%. Therefore, introducing BN bonds into benchmark polymers is a possible avenue toward higher-performance of OSCs.

Critical Role of Non-Halogenated Solvent Additives in Eco-Friendly and Efficient All-Polymer Solar Cells

Organic solar cells (OSCs) demonstrating high power conversion efficiencies have been mostly fabricated using halogenated solvents, which are highly toxic and harmful to humans and the environment. Recently, non-halogenated solvents have emerged as a potential alternative. However, there has been limited success in attaining an optimal morphology when non-halogenated solvents (typically o-xylene (XY)) were used. To address this issue, we studied the dependence of the photovoltaic properties of all-polymer solar cells (APSCs) on various high-boiling-point non-halogenated additives. We synthesized PTB7-Th and PNDI2HD-T polymers that are soluble in XY and fabricated PTB7-Th:PNDI2HD-T-based APSCs using XY with five additives: 1,2,4-trimethylbenzene (TMB), indane (IN), tetralin (TN), diphenyl ether (DPE), and dibenzyl ether (DBE). The photovoltaic performance was determined in the following order: XY + IN < XY + TMB < XY + DBE ≤ XY only < XY + DPE < XY + TN. Interestingly, all APSCs processed with an XY solvent system had better photovoltaic properties than APSCs processed with chloroform solution containing 1,8-diiodooctane (CF + DIO). The key reasons for these differences were unraveled using transient photovoltage and two-dimensional grazing incidence X-ray diffraction experiments. The charge lifetimes of APSCs based on XY + TN and XY + DPE were the longest, and their long lifetime was strongly associated with the polymer blend film morphology; the polymer domain sizes were in the nanoscale range, and the blend film surfaces were smoother, as the PTB7-Th polymer domains assumed an untangled, evenly distributed, and internetworked morphology. Our results demonstrate that the use of an additive with an optimal boiling point facilitates the development of polymer blends with a favorable morphology and can contribute to the widespread use of eco-friendly APSCs.

Linear Regulating of Polymer Acceptor Aggregation with Short Alkyl Chain Units Enhances All-Polymer Solar Cells' Efficiency

The power conversion efficiency (PCE) of all-polymer solar cells (all-PSCs) has ascended rapidly arising from the development of polymerized small-molecule acceptor materials. However, numerous insulating long alkyl chains, which ensure the solubility of the polymer, result in inferior aggregation and charge mobility. Herein, this study proposes a facile random copolymerization strategy of two small molecule acceptor units with different lengths of alkyl side chains and synthesizes a series of polymer acceptors PYT-EHx, where x is the percentage of the short alkyl chain units. The aggregation strength and charge mobility of the acceptors rise linearly with increasing the proportion of short alkyl chain units. Thus, the PYT-EH20 reaches balanced aggregation with the star polymer donor PBDB-T, resulting in optimal morphology, fastest carrier transport, and reduced recombination and energy loss. Consequently, the PYT-EH20-based device yields a 14.8% PCE, a 16% improvement over the control PYT-EH0-based device, accompanied by an increase in open-circuit voltage (V_oc ), short-circuit current density (J_sc ), and fill factor (FF). This work demonstrates that the random copolymerization strategy with short alkyl chain insertion is an effective avenue for developing high-performance polymer acceptors, which facilitates further advances in the efficiency of all-PSCs.

Modulation of Molecular Stacking via Tuning 2-Ethylhexyl Alkyl Chain Enables Improved Efficiency for All-Small-Molecule Organic Solar Cells

There is always a dilemma between strong π-π stacking/crystallinity and suitable domain size for all-small-molecule organic solar cells (ASM-OSCs), which puts forward higher requirements for the design of molecular donors. In this work, a series of novel molecular donors with different positional 2-ethylhexy (EH) attachments are designed and synthesized, named SM-R, SM-REH, SM-EH-R, and SM-EH-REH. It is found that EH-substitution on end groups (SM-REH) enables improved π-π interaction and crystallinity but with decreased solubility and phase size, leading to the improved efficiency of 15.6% as compared to 14.0% of SM-R. In contrast, EH-substitution on the π-bridge (SM-EH-R) significantly suppresses π-π stacking and increases the solubility, resulting in the lower efficiency of 11.9%. The further EH-substitution on end-groups of SM-EH-R, namely, SM-EH-REH, recovers the π-π stacking strength and obtains a moderate efficiency of 14.4%. Despite the higher crystallinity and increased π-π stacking in some molecules, the blend films show the gradually decreased domain size in the sequence of SM-R, SM-REH, SM-EH-R, and SM-EH-REH owing to the steric hindrance of the EH-chain. Overall, this work indicates that obtaining the higher π-π stacking/crystallinity and decreased domain size is achievable by tuning the EH-chain substitution, which paves the way to further improve the photovoltaic performance of ASM-OSCs.

Improved Molecular Ordering in a Ternary Blend Enables All-Polymer Solar Cells over 18% Efficiency

Although all-polymer solar cells (all-PSCs) show great commercialization prospects, their power conversion efficiencies (PCEs) still fall behind their small molecule acceptor-based counterparts. In all-polymer blends, the optimized morphology and high molecular ordering are difficult to achieve since there is troublesome competition between the crystallinity of the polymer donor and acceptor during the film-formation process. Therefore, it is challenging to improve the performance of all-PSCs. Herein, a ternary strategy is adopted to modulate the morphology and the molecular crystallinity of an all-polymer blend, in which PM6:PY-82 is selected as the host blend and PY-DT is employed as a guest component. Benefiting from the favorable miscibility of the two acceptors and the higher regularity of PY-DT, the ternary matrix features a well-defined fibrillar morphology and improved molecular ordering. Consequently, the champion PM6:PY-82:PY-DT device produces a record-high PCE of 18.03%, with simultaneously improved open-circuit voltage, short-circuit current and fill factor in comparison with the binary devices. High-performance large-area (1 cm² ) and thick-film (300 nm) all-PSCs are also successfully fabricated with PCEs of 16.35% and 15.70%, respectively.Moreover, 16.5 cm² organic solar module affords an encouraging PCE of 13.84% when using the non-halogenated solvent , showing the great potential of "Lab-to-Fab" transition of all-PSCs.

Formation of Efficient Quasi-All-Polymer Solar Cells by Synergistic Effect of the Ternary Strategy and Solid Additives

All-polymer solar cells (all-PSCs) have been widely studied owing to their unique mechanical flexibility and stability. However, all-PSCs have a lower efficiency than small-molecule acceptor-based PSCs. In the work, a ternary quasi-all-polymer solar cell (Q-all-PSC) using a synergy of the ternary strategy and solid additive engineering is reported. The introduction of PC₇₁BM can not only match the energy level of the photoactive materials with an improved open circuit voltage (V_OC) of the ternary devices but also enhance photon capture, which can improve short circuit current density. It is found that there is effective charge transfer between PC₇₁BM and PY-IT, which can form an electron transport channel and promote efficient charge transport. Moreover, the introduction of PC₇₁BM made the PM6/PY-IT/PC₇₁BM ternary blends more crystalline while slightly reducing phase separation, resulting in a suitable domain size. Importantly, by introducing a high dielectric-constant PFBEK solid additive as the fasten matrix, the Q-all-PSC's efficiency can reach 16.42%. This method provides a new idea for future research on all-polymer solar cells.

Ternary All-Polymer Solar Cells with Efficiency up to 18.14% Employing a Two-Step Sequential Deposition

Achieving a finely tuned active layer morphology with a suitable vertical phase to facilitate both charge generation and charge transport has long been the main goal for pursuing the highly efficient bulk heterojunction all-polymer solar cells (all-PSCs). Herein, a solution to address the above challenge via synergistically combining the ternary blend strategy and the layer-by-layer (LbL) procedure is proposed. By introducing a synthesized polymer acceptor (P_A ), PY-Cl, with higher crystallinity into the designed host acceptor PY-SSe-V, vertical phase distribution and molecular ordering of the LbL-type ternary all-PSCs can be improved in comparison to the LbL-type PM6/PY-SSe-V binary all-PSCs. The formation of the superior bulk microstructure can not only promote charge transport and extraction properties but also reduce energetic disorder and non-radiative recombination loss, thus improving all three photovoltaic parameters simultaneously. Consequently, the PM6/(PY-SSe-V:PY-Cl) ternary all-PSCs show the best efficiency of 18.14%, which is among the highest values reported to date for all-PSCs. This work provides a facile and effective LbL-type ternary strategy for obtaining high-efficiency all-PSCs.

Enhanced Performance of Flexible Organic Photovoltaics Based on MoS2 Micro-Nano Array

In this work, we investigated the influence of MoS₂ functioning as an electron transport layer (ETL) on the inverted flexible organic photovoltaics (FOPVs). Three ETLs, including MoS₂, lithium quinolate (Liq), and a MoS₂/Liq bilayer, were evaporated onto ITO-integrated polyethylene terephthalate substrates (PET-ITO), and the properties of transmittance, water contact angle, and reflectivity of the films were analyzed. The results revealed that MoS₂ was helpful to improve the lipophilicity of the surface of the ETL, which was conducive to the deposition of the active layer. In addition, the reflectivity of MoS₂ to the light ranging from 400 to 600 nm was the largest among the pristine PET-ITO substrate and the PET-ITO coated with three ETLs, which promoted the efficient use of the light. The efficiency of the FOPV with MoS₂/Liq ETL was 73% higher than that of the pristine device. This was attributed to the nearly two-fold amplification of the MoS₂ array to the light field, which promoted the FOPV to absorb more light. Moreover, the efficiency of the FOPV with MoS₂ was maintained under different illumination angles and bending angles. The results demonstrate the promising applications of MoS₂ in the fabrication of FOPVs.

Regulation of Polymer Configurations Enables Green Solvent-Processed Large-Area Binary All-Polymer Solar Cells With Breakthrough Performance and High Efficiency Stretchability Factor

With the great potential of the all-polymer solar cells for large-area wearable devices, both large-area device efficiency and mechanical flexibility are very critical but attract limited attention. In this work, from the perspective of the polymer configurations, two types of terpolymer acceptors PYTX-A and PYTX-B (X = Cl or H) are developed. The configuration difference caused by the replacement of non-conjugated units results in distinct photovoltaic performance and mechanical flexibility. Benefiting from a good match between the intrinsically slow film-forming of the active materials and the technically slow film-forming of the blade-coating process, the toluene-processed large-area (1.21 cm² ) binary device achieves a record efficiency of 14.70%. More importantly, a new parameter of efficiency stretchability factor (ESF) is proposed for the first time to comprehensively evaluate the overall device performance. PM6:PYTCl-A and PM6:PYTCl-B yield significantly higher ESF than PM6:PY-IT. Further blending with non-conjugated polymer donor PM6-A, the best ESF of 3.12% is achieved for PM6-A:PYTCl-A, which is among the highest comprehensive performances.