Stamping Fabrication of Flexible Planar Micro-Supercapacitors Using Porous Graphene Inks

Signal amplification strategies in photoelectrochemical sensing of carcinoembryonic antigen

Early detection of cancer markers is critical for cancer diagnosis and cancer therapy since these markers may indicate cancer risk, incidence, and disease prognosis. Carcinoembryonic antigen (CEA) is a type of non-specific and broad-spectrum cancer biomarker commonly utilized for early cancer diagnosis. Moreover, it serves as an essential tool to assess the efficacy of cancer treatment and monitor tumor recurrence as well as metastasis, thus garnering significant attention for precise and sensitive CEA detection. In recent years, photoelectrochemical (PEC) techniques have emerged as prominent methods in CEA detection due to the advantages of PEC, such as simple equipment requirements, cost-effectiveness, high sensitivity, low interference from background signals, and easy of instrument miniaturization. Different signal amplification methods have been reported in PEC sensors for CEA analysis. Based on these, this article reviews PEC sensors based on various signal amplification strategies for detection of CEA during the last five years. The advantages and drawbacks of these sensors were discussed, as well as future challenges.

Carbon Micro/Nano Machining toward Miniaturized Device: Structural Engineering, Large-Scale Fabrication, and Performance Optimization

With the rapid development of micro/nano machining, there is an elevated demand for high-performance microdevices with high reliability and low cost. Due to their outstanding electrochemical, optical, electrical, and mechanical performance, carbon materials are extensively utilized in constructing microdevices for energy storage, sensing, and optoelectronics. Carbon micro/nano machining is fundamental in carbon-based intelligent microelectronics, multifunctional integrated microsystems, high-reliability portable/wearable consumer electronics, and portable medical diagnostic systems. Despite numerous reviews on carbon materials, a comprehensive overview is lacking that systematically encapsulates the development of high-performance microdevices based on carbon micro/nano structures, from structural design to manufacturing strategies and specific applications. This review focuses on the latest progress in carbon micro/nano machining toward miniaturized device, including structural engineering, large-scale fabrication, and performance optimization. Especially, the review targets an in-depth evaluation of carbon-based micro energy storage devices, microsensors, microactuators, miniaturized photoresponsive and electromagnetic interference shielding devices. Moreover, it highlights the challenges and opportunities in the large-scale manufacturing of carbon-based microdevices, aiming to spark further exciting research directions and application prospectives.

Recent Progress and Challenges in Paper-Based Microsupercapacitors for Flexible Electronics: A Comprehensive Review

Recent advances in paper-based microsupercapacitors (p-MSCs) have attracted significant attention due to their potential as substrates for flexible electronics. This review summarizes progress in the field of p-MSCs, discussing their challenges and prospects. It covers various aspects, including the fundamental characteristics of paper, the modification of paper with functional materials, and different methods for device fabrication. The review critically analyzes recent advancements, materials, and fabrication techniques for p-MSCs, exploring their potential applications and benefits, such as flexibility, cost-effectiveness, and sustainability. Additionally, this review highlights gaps in current research, guiding future investigations and innovations in the field. It provides an overview of the current state of p-MSCs and offers valuable insights for researchers and professionals in the field. The critical analysis and discussion presented herein offer a roadmap for the future development of p-MSCs and their potential impact on the domain of flexible electronics.

Electrochemically Exfoliated Graphene Additive-Free Inks for 3D Printing Customizable Monolithic Integrated Micro-Supercapacitors on a Large Scale

Three-dimensional (3D) printing technology with enhanced fidelity can achieve multiple functionalities and boost electrochemical performance of customizable planar micro-supercapacitors (MSCs), however, precise structural control of additive-free graphene-based macro-assembly electrode for monolithic integrated MSCs (MIMSCs) remains challenging. Here, the large-scale 3D printing fabrication of customizable planar MIMSCs is reported utilizing additive-free, high-quality electrochemically exfoliated graphene inks, which is not required the conventional cryogenic assistance during the printing process and any post-processing reduction. The resulting MSCs reveal an extremely small engineering footprint of 0.025 cm2, exceptionally high areal capacitance of 4900 mF cm-2, volumetric capacitance of 195.6 F cm-3, areal energy density of 2.1 mWh cm-2, and unprecedented volumetric energy density of 23 mWh cm-3 for a single cell, surpassing most previously reported 3D printed MSCs. The 3D printed MIMSC pack is further demonstrated, with the maximum areal cell count density of 16 cell cm-2, the highest output voltage of 192.5 V and the largest output voltage per unit area of 56 V cm-2 up to date are achieved. This work presents an innovative solution for processing high-performance additive-free graphene ink and realizing the large-scale production of 3D printed MIMSCs for planar energy storage.

S-NiSe/HG Nanocomposites with Balanced Dielectric Loss Encapsulated in Room-Temperature Self-Healing Polyurethane for Microwave Absorption and Corrosion Protection

Exploring anticorrosion electromagnetic wave (EMW) absorbing materials in harsh conditions remains a challenge. Herein, S-NiSe/HG nanocomposites encapsulated in room-temperature self-healing polyurethane (S-NiSe/HG/SPU) were exploited as superior anticorrosion EMW absorbing materials. A dual-defect engineering collaborative Schottky interface construction endows S-NiSe/HG with a high vacancy concentration, abundant defects, and moderate conductivity. These structural merits synergistically balance dielectric loss by enhancing dipole-interface polarization loss and optimizing conduction loss. As a result, S-NiSe/HG demonstrates the optimal EMW absorption performance with a minimum reflection loss (RLmin) of -54.8 dB and an adequate absorption bandwidth (EAB) of 7.1 GHz. Besides, S-NiSe/HG/SPU combines the maze effect of S-NiSe/HG with the active repair capability of SPU, thereby providing long-term corrosion resistance for the Mg alloy. Even under corrosion for 10 days, S-NiSe/HG/SPU affords a low corrosion current density (1.3 × 10-5 A) and high charge transfer resistance (3796 Ω cm2). Overall, this work provides valuable insights for in-depth exploration of dielectric loss and development of multifunctional EMW-absorbing materials.

Multiscale Structural Design of 2D Nanomaterials-based Flexible Electrodes for Wearable Energy Storage Applications

2D nanomaterials play a critical role in realizing high-performance flexible electrodes for wearable energy storge devices, owing to their merits of large surface area, high conductivity and high strength. The electrode is a complex system and the performance is determined by multiple and interrelated factors including the intrinsic properties of materials and the structures at different scales from macroscale to atomic scale. Multiscale design strategies have been developed to engineer the structures to exploit full potential and mitigate drawbacks of 2D materials. Analyzing the design strategies and understanding the working mechanisms are essential to facilitate the integration and harvest the synergistic effects. This review summarizes the multiscale design strategies from macroscale down to micro/nano-scale structures and atomic-scale structures for developing 2D nanomaterials-based flexible electrodes. It starts with brief introduction of 2D nanomaterials, followed by analysis of structural design strategies at different scales focusing on the elucidation of structure-property relationship, and ends with the presentation of challenges and future prospects. This review highlights the importance of integrating multiscale design strategies. Finding from this review may deepen the understanding of electrode performance and provide valuable guidelines for designing 2D nanomaterials-based flexible electrodes.

Ultrafast alternating-current exfoliation toward large-scale synthesis of graphene and its application for flexible supercapacitors

To facilitate the transition of laboratory research to industrial applications, it is critical to establish a reliable protocol for the mass synthesis of high-quality graphene. Here, we present an efficient electrochemical intercalation-based exfoliation approach utilizing alternating current that allows for the production of sub-kilogram quantities of graphene. This strategy involves repeatedly intercalating foreign anions and cations into the interlayer gaps of dual-graphite electrodes, accelerating the graphite expansion process and maximizing the exfoliation efficiency of both electrodes while inhibiting excessive anodic oxidation. The exfoliation process leads to high-yield graphene nanosheets (92 %, primarily 1-3 layers) with minimal structural deterioration (ID/IG ratio of 0.05), high purity (2.1 at% oxygen), and outstanding electrical property (7.28 × 104 S m-1). Notably, our scaled-up manufacturing technique produces a record-breaking throughput of 135 g h-1, improving on the best-reported exfoliation efficiency with direct current by 35%. Furthermore, the as-made graphene demonstrates a large reversible capacity of 102 mF cm-2 for flexible supercapacitors, with robust cyclability with 99.5% after 10,000 cycles, excellent mechanical flexibility, and exceptional serial integration for adjustable voltage output. The efficient and scalable method presents a significant advancement in the large-scale manufacture of graphene, with potential for widespread industrial applications.

Zn Microbatteries Explore Ways for Integrations in Intelligent Systems

As intelligent microsystems develop, many revolutionary applications, such as the swallowing surgeon proposed by Richard Feynman, are about to evolve. Nonetheless, integrable energy storage satisfying the demand for autonomous operations has emerged as a major obstacle to the deployment of intelligent microsystems. A reason for the lagging development of integrable batteries is the challenge of miniaturization through microfabrication procedures. Lithium batteries, generated by the most successful battery chemistry, are not stable in the air, thus creating major manufacturing challenges. Other cations (Na⁺ , Mg²⁺ , Al³⁺ , K⁺ ) are still in the early stages of development. In contrast, the superior stability of zinc batteries in the air brings high compatibility to microfabrication protocols and has already demonstrated excellent practicability in full-sized devices. To obtain energy-dense and high-power zinc microbatteries within square-millimeter or smaller footprints, sandwich, pillar, and Swiss-roll configurations are developed. Thin interdigital and fiber microbatteries find their applications being integrated into wearable devices and electronic skin. It is foreseeable that zinc microbatteries will find their way into highly integrated microsystems unlocking their full potential for autonomous operation. This review summarizes the material development, configuration innovation, and application-oriented integration of zinc microbatteries.

Selective H2O2 Electrosynthesis over Defective Carbon from Electrochemical Etching of Molybdenum Carbide

The controllable synthesis of specific defective carbon catalysts is crucial for two-electron oxygen reduction reaction (2e^- ORR) to generate H₂O₂ due to the great potential applications. Herein, the defective carbon catalysts (Mo-CDC-ns) were prepared by an electrochemical activation (ECA) method with Mo₂C/C as a parent. Electrochemical cyclic voltammetry curves, X-ray photoelectron spectroscopy, inductively coupled plasma-mass spectrometry, scanning electron microscopy, and high-resolution transmission electron microscopy confirm the evolution process of a defective carbon structure from the Mo₂C phase in which Mo species are first oxidized to Mo⁶⁺ species and then the latter are dissolved into the solution and defective carbon is simultaneously formed. Raman and electron paramagnetic resonance spectra reveal that the defect types in Mo-CDC-ns are the edge defect and vacancy defect sites. Compared with the parent Mo₂C/C, Mo-CDC-ns exhibit gradually increased kinetic current density and selectivity for H₂O₂ generation with an extension of activation cycles from 10 (Mo-CDC-10) to 30 (Mo-CDC-30). Over Mo-CDC-30, a kinetic current density of 19.4 mA cm^-2 and a selectivity close to 90% in 0.1 M KOH solution were achieved, as well as good stability for H₂O₂ production in an extended test up to 12 h in an H-cell. Graphene planes and Stone Wales 5757-carbon were constructed as basic models for density functional theory calculations. It revealed that the obtained defective structure after the removal of Mo atoms contains the double vacancy at the edge of graphene (Edge-DVC) and the topological defect on the plane of 5757-carbon (5757C-D), which show more moderate reaction free energy for forming *OOH and smaller energy barrier of 2e^- ORR.

Paper-based laser-induced graphene for sustainable and flexible microsupercapacitor applications

Laser-induced graphene (LIG) is as a promising material for flexible microsupercapacitors (MSCs) due to its simple and cost-effective processing. However, LIG-MSC research and production has been centered on non-sustainable polymeric substrates, such as polyimide. In this work, it is presented a cost-effective, reproducible, and robust approach for the preparation of LIG structures via a one-step laser direct writing on chromatography paper. The developed strategy relies on soaking the paper in a 0.1 M sodium tetraborate solution (borax) prior to the laser processing. Borax acts as a fire-retardant agent, thus allowing the laser processing of sensitive substrates that other way would be easily destroyed under the high-energy beam. LIG on paper exhibiting low sheet resistance (30 Ω sq^-1) and improved electrode/electrolyte interface was obtained by the proposed method. When used as microsupercapacitor electrodes, this laser-induced graphene resulted in specific capacitances of 4.6 mF cm^-2 (0.015 mA cm^-2). Furthermore, the devices exhibit excellent cycling stability (> 10,000 cycles at 0.5 mA cm^-2) and good mechanical properties. By connecting the devices in series and parallel, it was also possible to control the voltage and energy delivered by the system. Thus, paper-based LIG-MSC can be used as energy storage devices for flexible, low-cost, and portable electronics. Additionally, due to their flexible design and architecture, they can be easily adapted to other circuits and applications with different power requirements.

Preparation of Three-Dimensional Porous Graphene by Hydrothermal and Chemical Reduction with Ascorbic Acid and its Electrochemical Properties

Three-dimensional porous graphene (3D-PG) has attracted much attention due to its excellent electrochemical performance. Chemical reduction is one of common methods for preparing porous graphene. In order to develop a green and facile method for preparing three-dimensional porous graphene, in this paper, 3D-PG was fabricated by reduction of graphene oxide (GO) with ascorbic acid (AA) as reductant in hydrothermal condition based on non-toxic, non-flammable and mild reducing performance of ascorbic acid. It was found that the size and distribution of pores could be controlled by the reduction time and the concentration of AA in the solution. The pore sizes in R0, R1 and R2 were in the range of 0.5-1 μm, 1-1.5 μm, and 1.5-3 μm, respectively. It was found that the average pore size and volume increased along with the amount of reductants. Under optimal conditions - a reaction time of 20 h and a ratio of GO to AA=1 : 1 - the CV area of the so-obtained sample R1-20 at 100 mV was 0.06 and the specific capacitance of the 3D-PG electrode reaches 153.5 F ⋅ g^-1 , which is suitable for use in supercapacitors.

Biocompatible Parylene-C Laser-Induced Graphene Electrodes for Microsupercapacitor Applications

Laser irradiation of polymeric materials has drawn great attention as a fast, simple, and cost-effective method for the formation of porous graphene films that can be subsequently fabricated into low-cost and flexible electronic and energy-storage devices. In this work, we report a systematic study of the formation of laser-induced graphene (LIG) with sheet resistances as low as 9.4 Ω/sq on parylene-C ultrathin membranes under a CO₂ infrared laser. Raman analysis proved the formation of the multilayered graphenic material, with I_D/I_G and I_2D/I_G peak ratios of 0.42 and 0.65, respectively. As a proof of concept, parylene-C LIG was used as the electrode material for the fabrication of ultrathin, solid-state microsupercapacitors (MSCs) via a one-step, scalable, and cost-effective approach, aiming at future flexible and wearable applications. The produced LIG-MSC on parylene-C exhibited good electrochemical behavior, with a specific capacitance of 1.66 mF/cm² and an excellent cycling stability of 96% after 10 000 cycles (0.5 mA/cm²). This work allows one to further extend the knowledge in LIG processes, widening the group of precursor materials as well as promoting future applications. Furthermore, it reinforces the potential of parylene-C as a key material for next-generation biocompatible and flexible electronic devices.

Engineering Interlaced Architecture of Pristine Graphene Anchored with 2-Amino-8-Naphthol 6-Sulfonic Acids for Printed Hybrid Micro-Supercapacitors with High Electrochemical Capability

All-printed flexible micro-supercapacitors (MSCs) based on two-dimensional (2D) nanomaterials with in-plane interdigital configurations are regarded as promising miniaturized power source units, but they chronically suffer from self-aggregation and inadequate matching of electrode materials, thus resulting in inefficient electrolyte ions intercalation. Herein, an innovative multicomponent interlaced architecture essentially consisting of 2-amino-8-naphthol 6-sulfonic acid (ANS)-anchored pristine graphene and highly conductive multiwalled carbon nanotubes is reported. The assembled and optimized Gr@ANS electrodes offer sufficient absorption/desorption and redox-active sites, delivering a high areal capacitance of 33.7 mF/cm² for screen-printed MSCs. Particularly, the well-modified Gr@ANS/CNTs-interlaced complex structure effectively prevents the usual restacking of the delaminated Gr@ANS nanosheets and maximizes ion accessibility in electrodes. Ascribed to the optimized electron-transferring kinetics, the achieved Gr@ANS/CNTs MSCs exhibit excellent capacitance (40.2 mF/cm² and 18.8 F/cm³), simultaneously significantly increasing the rate capability of Gr@ANS MSCs (from 3.9 to 60.0%). Arising from the multicomponent synergism, the all-solid-state MSCs exhibit outstanding bending stability and cycling performance (73.8% after 10 000 charge/discharge cycles). The new charge reservoir engineering evidenced in graphene-based micro-supercapacitors would serve as a stepping stone toward the scalable manufacture of hybrid energy storage micro-devices.

Facile Synthesis of Ag/Carbon Quantum Dots/Graphene Composites for Highly Conductive Water-Based Inks

The development of graphene conductive inks with a high conductivity and dispersion stability in water poses considerable challenges. Herein, a highly conductive Ag/carbon quantum dots (CQDs)/graphene (G) composite with good dispersity and stability in water was prepared for the first time through the in situ photoreduction of AgNO3 and deposition of Ag onto graphene nanosheets obtained via CQD-assisted liquid-phase exfoliation. Ag nanoparticles with an average size of ∼1.88 nm were uniformly dispersed on graphene nanosheets. The Ag/CQDs/G composite exhibited good dispersity and stability in water for 30 days. The formation mechanism of the Ag/CQDs/G composites was also discussed. CQDs played a vital role in coordinating with Ag+ and reducing it under visible light conditions. The addition of only 1.58 wt % of Ag NPs to the CQDs/G film resulted in a significant decrease in the electrical resistivity by approximately 89.5%, reaching a value of 0.054 Ω cm for a 40 μm thick Ag/CQDs/G film. A low resistivity of 2.15 × 10-3 Ω cm for the Ag/CQDs/G film was achieved after rolling compression with a compression ratio of 78%. The Ag/CQDs/G film exhibited good conductivity and durability when bent, rolled, or twisted. Moreover, the resistivity of the film displayed a slight deviation after 5000 bending cycles, indicating its outstanding stability. This study provides an efficient strategy for preparing graphene-based conductive composites with good dispersibility and stability in water as well as novel high-performance conductive inks for application in flexible printed electronics.

Electrochemically Exfoliated Chlorine-Doped Graphene for Flexible All-Solid-State Micro-Supercapacitors with High Volumetric Energy Density

Graphene-constructed micro-supercapacitors (MSCs) have received considerable attention recently, as part of the prospective wearable and portable electronics, owing to their distinctive merits of well-tunable power output, robust mechanical flexibility, and long cyclability. In the current work, the focus is on the fabrication of high-quality and solution-processible chlorine-doped graphene (Cl-G) nanosheets through a handy yet eco-friendly electrochemical exfoliation process. The Cl-G is characteristic of the large lateral size of ≈10 µm, abundant nanopores with sizes of as small as 2 nm, as well as numerous steps from the rugged surface. Arising from the rich chemical functionalities and structure defects, the all-solid-state MSC built by using Cl-G via a facile mask-assisted method delivers a large reversible capacity and ultrasteady charge/discharge performance, with the capacitance being maintained at 98.1% even after 250 000 cycles. The Cl-G-MSC with EMIMBF₄ /PVDF-HFP as the electrolyte displays a large volumetric capacitance up to 160 F cm^-3 at the scan rate of 5 mV s^-1 and high volumetric energy density of 97.9 mW h cm^-3 at the power density of 3.4 W cm^-3 . The device can also output a high voltage up to 3.5 V and robust capability with 94.8% of capacitance retention upon 10 000 cycles.

Tailoring surface carboxyl groups of mesoporous carbon boosts electrochemical H2O2 production

Oxygen-doped porous carbon materials have been shown promising performance for electrochemical two-electron oxygen reduction reaction (2e^- ORR), an efficient approach for the safe and continuous on-site generation of H₂O₂. The regulation and mechanism understanding of active oxygen-containing functional groups (OFGs) remain great challenges. Here, OFGs modified porous carbon were prepared by thermal oxidation (MC-12-Air), HNO₃ oxidation (MC-12-HNO₃) and H₂O₂ solution hydrothermal treatment (MC-12-H₂O₂), respectively. Structural characterization showed that the oxygen doping content of three catalysts reached about 20%, with the almost completely maintained specific surface area (exception of MC-12- HNO₃). Spectroscopic characterization further revealed that hydroxyl groups are mainly introduced into MC-12-Air, while carboxyl groups are mainly introduced into MC-12- HNO₃ and MC-12- H₂O₂. Compared with the pristine catalyst, three oxygen-functionalized catalysts showed enhanced activity and H₂O₂ selectivity in 2e^- ORR. Among them, MC-12-H₂O₂ exhibited the highest catalytic activity and selectivity of 94 %, as well as a considerable HO₂^- accumulation of 46.2 mmol L^-1 and excellent stability in an extended test over 36 h in a H-cell. Electrochemical characterization demonstrated the promotion of OFGs on ORR kinetics and the greater contribution of carboxyl groups to the intrinsically catalytic activity. DFT calculations confirmed that the electrons are transferred from carboxyl groups to adjacent carbon and the enhanced adsorption strength toward *OOH intermediate, leading to a lower energy barrier for forming *OOH on carboxyl terminated carbon atoms.

Controllable synthesis of NiCo layered double hydroxide sheets on laser-induced graphene as electrodes for high-performance supercapacitors

NiCo-LDH@P12-LIG electrodes are prepared using the laser-induced graphene under hydrothermal conditions, showing an areal specific capacitance of 2072 mF cm−2.

High Mass Loading Asymmetric Micro-supercapacitors with Ultrahigh Areal Energy and Power Density

High mass loading asymmetric micro-supercapacitors (MSCs) are key components for the development of high-performance energy and power supply systems. Here, a concept for achieving high mass loading electrodes is presented and applied to high mass loading micro-supercapacitors with ultrahigh areal energy and power density. The positive electrode is made from porous carbon with birnessite coverage and multiwalled carbon nanotubes (CNTs) as conducting additives (PIC-CNTs-MnO₂). The negative electrode is prepared from hierarchically porous active carbon mixed with CNTs (PICK-CNTs). Both positive and negative electrode materials are tailored to ensure a high content of macro- and mesopores. MSCs with an optimized mass loading of 13.9 mg·cm^-2 (maximum: 23.6 mg·cm^-2) provide an ultrahigh areal capacitance of 1.13 F·cm^-2 (volumetric capacitance: 22.6 F·cm^-3), an outstanding energy of 627.8 μWh·cm^-2, and a maximum power density of 64 mW·cm^-2. About 85% of the initial capacitance remained after 5000 cycles. Moreover, shunt and tandem device testing confirmed a high uniformity of these MSCs, meeting the requirements of adjustable output currents and voltages in microchips.

Planar Graphene-Based Microsupercapacitors

With the development of wearable, portable, and implantable electronic devices, flexible and on-chip microsupercapacitors (MSCs) are urgently needed for miniaturized energy storage. Planar MSCs have high power density, fast charge/discharge rate, and long operating lifetime, and can adapt to future flexible, integrated, and miniaturized electronic systems for wide application foreground. Due to the high specific surface area, outstanding electrical conductivity, and excellent electron mobility, graphene shows promising advantages in planar MSCs devices, thus stimulates wide-ranging research in the last few years. Herein, the recent progress of planar graphene-based MSCs, including the intrinsic structure regulation of graphene-based electrode materials, the specific fabrication techniques, the multifunctional integration, and various applications of MSCs as flexible and on-chip energy storage is systematically summarized. The key challenges and prospects of future planar graphene-based MSCs are also discussed targeting to realize their practical applications.

Zinc-salt assisted synthesis of three-dimensional oxygen and nitrogen co-doped hierarchical micro-meso porous carbon foam for supercapacitors

Nitrogen and oxygen co-doped hierarchical micro-mesoporous carbon foams has been synthesized by pyrolyzation treatment of a preliminary foam containing melamine and formaldehyde as nitrogen, carbon and oxygen precursors and Zn(NO3)2. 6H2O and pluronic F127 as micro-meso pores generators. Several characterizations including thermal gravimetric analysis (TGA), X-ray diffraction (XRD) and Raman spectroscopy, FTIR and X-ray photoelectron spectroscopy, N2 adsorption-desorption, field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM) were performed on the prepared foams. X-ray diffraction patterns, Raman spectra and N2 adsorption-desorption results confirmed that ZnO has pronounced effect on the graphitization of the prepared carbon foam. From X-ray diffraction, thermal gravimetric and N2 adsorption-desorption analysis results it was confirmed that the carbothermal reaction and the elimination of ZnO and also the elimination of pluronic F127 are the main factors for the induction of porosities in the foam structure. The presence of Zn(NO3)2. 6H2O and pluronic F127 in the initial composition of the preliminary foam results in the specific surface area as high as 1176 m2.g-1 and pore volume of 0.68 cm3.g-1. X-ray photoelectron and FTIR spectroscopy analyses results approved the presence of nitrogen (about 1.9 at %) in the form of pyridinic, graphitic and nitrogen oxide and oxygen (about 7.5 at. %) functional groups on the surface of the synthesized carbon foam. Electrochemistry analysis results including cyclic voltammetry (CV) and galvanostatic charge-discharge (GCD) and also electrochemical impedance spectroscopy (EIS) analysis illustrated the formation of an electric double layer supercapacitor with the capacitance as high as 137 Fg-1.

A multidimensional rational design of nickel-iron sulfide and carbon nanotubes on diatomite via synergistic modulation strategy for supercapacitors

Based on their characteristics, transition metal layered double hydroxides have been of great scientific interest for their use in supercapacitors. Up until now, severe aggregation and low intrinsic conductivity have been the major hurdles for their application. In this work, nickel-iron sulfide nanosheets (NiFeSx) and carbon nanotubes (CNTs) were synthesized on diatomite using chemical vapor deposition and a two-step hydrothermal method to overcome these challenges. Synthesis of this composite successfully exploits the synergistic effect of multicomponent materials to improve the electrochemical performance. Diatomite is selected as a substrate to provide preferable surroundings for the uniform dispersion of nanomaterial on its surface, which enlarges the active sites that come in contact with the electrolytes, significantly improving the electrochemical properties. Combined with high conductivity and a synchronous sulfurization effect, the NiFeSx@CNTs@MnS@Diatomite electrode delivered a high specific capacitance of 552F g^-1 at a current density of 1 A g^-1, a good rate capability of 68.4% retention at 10 A g^-1, and superior cycling stability of 89.8% capacitance retention after 5000 cycles at 5 A g^-1. Furthermore, an asymmetric supercapacitor assembled via NiFeSx@CNTs@MnS@Diatomite and graphene delivered a maximum energy density of 28.9 Wh kg^-1 and a maximum power density of 9375 W kg^-1 at a potential of 1.5 V. This research lays the groundwork for ideal material preparation as well as a rational design for the electrode material, including property enhancement of diatomite-based material for use in supercapacitors.