Bio-nanocomposite films based on cellulose nanocrystals filled polyvinyl alcohol/chitosan polymer blend

Preparation, characterization, and application of gallic acid-mediated photodynamic chitosan-nanocellulose-based films

In this study, an active film composed of gallic acid (GA), chitosan (CS), and cellulose nanocrystals (CNC) was prepared using a solution casting method and synergistic photodynamic inactivation (PDI) technology. Characterization of the film showed that the CS-CNC-GA composite film had high transparency and UV-blocking ability. The addition of GA (0.2 %-1.0 %) significantly enhanced the mechanical properties, water resistance, and thermal stability of the film. The tensile strength increased up to 46.30 MPa, and the lowest water vapor permeability was 1.16 × e-12 g/(cm·s·Pa). The PDI-treated CS-CNC-GA1.0 composite film exhibited significantly enhanced antibacterial activity, with inhibition zone diameters of 31.83 mm against Staphylococcus aureus and 21.82 mm against Escherichia coli. The CS-CNC-GA composite film also showed good antioxidant activity. Additionally, the CS-CNC-GA1.0 composite film generated a large amount of singlet oxygen under UV-C light irradiation. It was found that using the CS-CNC-GA1.0 composite film for packaging and storage of oysters at 4 °C effectively delayed the increase in pH, total colony count, and lipid oxidation in oysters. In conclusion, the CS-CNC-GA composite film based on PDI technology has great potential for applications in the preservation of aquatic products.

Development of ternary polymeric film based on modified mango seed kernel starch, carboxymethyl cellulose, and gum acacia to extend the shelf-life of bun-bread

Non-conventional starch sources have attracted substantial attention due to their preferred physicochemical and mechanical properties similar to conventional sources. This study aimed to enhance the mechanical properties of mango seed kernel starch (MSKS) based films reinforced with carboxymethyl cellulose (CMC) and gum acacia (GA). Physical modification of MSKS was carried out using microwave-assisted at 180 W for 1 min. SEM results confirmed the oval and irregular shape of starch. The particle size of native starch (NS) (754.9 ± 20.4 nm) was higher compared to modified starch (MS) 336.6 ± 88.9 nm with a surface charge of -24.80 ± 3.92 to -34.87 ± 3.92 mV, respectively. Several functional groups including hydroxyl (OH) and carboxyl (CH) were confirmed in NS and MS. Different ratios of the MS, NS, CMC, and GA were used for the fabrication of films. Results revealed the higher tensile strength of M/C/G-1 (57.45 ± 0.05 nm) and M/C/G-2 (50.77 ± 0.58), compared to control C-4 (100 % native starch) (4.82 ± 0.04) respectively. The ternary complex provided excellent permeability against moisture and the film with a higher starch concentration confirmed the uniform thickness (0.09-0.10 mm). Furthermore, selected films (M/C/G-1 and M/C/G-2) reduced the microbial growth and weight loss of the bun compared to the control (C-4) film. Thus, the ternary complex maintained the freshness of the bun-bread for 14 days. It can be potentially used as a cost-effective and eco-friendly packaging material for food applications.

Advances in sustainable food packaging applications of chitosan/polyvinyl alcohol blend films

Researchers are addressing environmental concerns related to petroleum-based plastic packaging by exploring biopolymers from natural sources, chemical synthesis, and microbial fermentation. Despite the potential of individual biopolymers, they often exhibit limitations like low water resistance and poor mechanical properties. Blending polymers emerges as a promising strategy to overcome these challenges, creating films with enhanced performance. This review focuses on recent advancements in chitosan/polyvinyl alcohol (PVA) blend food packaging films. It covers molecular structure, properties, strategies for performance improvement, and applications in food preservation. The blend's excellent compatibility and intermolecular interactions make it a promising candidate for biodegradable films. Future research should explore large-scale thermoplastic technologies and investigate the incorporation of additives like natural extracts and nanoparticles to enhance film properties. Chitosan/PVA blend films offer a sustainable alternative to petroleum-based plastic packaging, with potential applications in practical food preservation.

Improving the optical, thermal, mechanical, electrical properties and antibacterial activity of PVA-chitosan by biosynthesized Ag nanoparticles: Eco-friendly nanocomposites for food packaging applications

In this study, nanocomposite films were produced by blending polyvinyl alcohol (PVA) and chitosan (Cs) polymers with 70 % PVA and 30 % Cs, incorporating silver nanoparticles (Ag NPs) via a solution-casting method. The research aims to investigate the impact of the biosynthesized Ag NPs by Chenopodium murale leaf extract on optical, morphological, mechanical, thermal, electrical, and antibacterial properties. XRD analysis showed a decrease in crystallinity degree with Ag NPs addition. TEM revealed Ag NPs in cubic and spherical shapes with an average size of 23.4 nm. SEM and AFM indicated surface morphology changes. FT-IR spectra showed interaction between Ag ions and the blend. The energy gap decreased with increasing Ag NPs concentration. TGA exhibited enhanced thermal stability. Mechanical properties improved significantly. AC electrical conductivity and dielectric parameters were studied. Antibacterial activity against Gram-positive and Gram-negative bacteria was observed. Overall, PVA/Cs-Ag NPs films show promise for food packaging and optoelectronic applications.

Sustainable reclamation of synthetic materials as automotive parts replacement: effects of environmental response on natural fiber vulnerabilities

Sustaining the resilience of the environment against climate change volatilities is fast becoming a herculean task considering the vulnerabilities of the ecosystem and disruption of the global value chain. Environmental crisis emanating from improper containment of synthetic materials is a major impediment facing the world today, and the situation could get worse if urgent measures are not devised to mitigate the quantity of waste synthetic materials that find its ways to the environment. These wastes are released in the form of toxins, posing danger to the environments, causing biodiversity loss and the degradation of already battered-climate. In this paper, the authors apprise existing containment measures of synthetic waste materials taking a preliminary and on-the-spot assessment of their impacts and effectiveness of their application leading to their operation. The prospect of waste glass fiber in automotive part replacement is given utmost interest in this paper, in which, a significant quantity of glass fiber could be used as part of automotive materials to reduce their overbearing environmental carnage. By this approach, the emerging automotive parts may have their strength and durability enhanced against impact and corrosion. Mindful of the non-biodegradable properties of glass fibers, the paper captures how effective these fibers could be used as automotive parts against the traditional materials. This paper also reflects on the response of the natural fiber in terms of their sustainability, as natural forest faces severe extinction occasioned by anthropogenic activities.

Experimental investigations on PVA/chitosan and PVA/chitin films for active food packaging using Oxytenanthera abyssinica lignin nanoparticles and its UV-shielding, antimicrobial, and antiradical effects

This study investigated the effect of adding lignin nanoparticles (LNPs) derived from Oxytenanthera abyssinica via alkali-acid nanoprecipitation method to polyvinyl alcohol/chitosan (PVA/CI) and polyvinyl alcohol/chitin (PVA/CH) films for the active food packaging applications. Adding LNPs at concentrations of 1 % and 3 % improved the films' thermal stability and mechanical properties. The lowest water solubility and moisture content were observed in PVA/CI/LNPs films. LNPs exhibited effective 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging activities, with the highest values observed in PVA/CH/LNPS and PVA/CI/LNPS films with values of 87.47 and 88.74 % respectively. The addition of LNPs also improved the UV-blocking abilities of the films. PVA/CH/LNP3 and PVA/CI/LNP3 have the smallest percentage transmission values of 3.34 % and 0.86 % in the UV range. The overall migration of dietary stimulants was lower in PVA/CI/LNPS and PVA/CH/LNPS films compared to PVA film. Antibacterial tests demonstrated the inhibitory capacity of the synthesized biofilms against both gram-positive and negative bacterial species, with the highest inhibitory value of 26 mm. The study suggests that PVA/CH/LNPS and PVA/CI/LNPS films have potential applications as active food packaging materials and can be explored in other potential applications such as drug delivery, tissue engineering, wound healing, and slow-release urea fertilizer development.

Efficient removal of ethidium bromide from aqueous solutions using chromatin-loaded chitosan polyvinyl alcohol composites

In this work, a novel chromatin-loaded chitosan polyvinyl alcohol composite was developed as a simple, efficient and environmentally friendly adsorbent for the efficient removal of ethidium bromide (EtBr). SEM images showed that the composites were characterized by dense porous and uniformly distributed morphology. The BET analysis showed the presence of mesopores and macropores in the composites. FTIR and XRD results showed that the chromatin was uniformly dispersed in the chitosan-polyvinyl alcohol carrier through hydrogen bonding. The fluorescence microscopy images showed the change of fluorescence effect before and after the adsorption of the material, which indicated that the chromatin was uniformly distributed in the composites and had a good adsorption effect. The optimal experimental conditions were T = 30℃, t = 120 min, pH = 7.4, m = 0.2 g when the composite with only 5% chromatin content had the ability to adsorb EtBr efficiently (minimum concentration 2 mg·L-1: adsorption rate 99%; maximum concentration 20 mg·L-1: adsorption rate 90%).The adsorption kinetics and thermodynamics showed that the EtBr adsorption kinetics of the composite conformed to the pseudo-second-order kinetic model (0.995 < R2 < 0.999) and the Freundlich isothermal model, and was a spontaneous process (ΔH < 0). This study on the immobilization of chromatin will provide a new way and reference for the application of chromatin in the treatment of EtBr pollutants.

Novel PVA/chitosan composite membrane modified using bio-fabricated α-MnO2 nanoparticles for photocatalytic degradation of cationic dyes

By integrating the benefits of poly vinyl alcohol (PVA) and chitosan (CS) with α-MnO₂ nanoparticles (MNPs), a novel type of nano-polymer composite (PVA/CS-MNP) membrane was synthesized through a simple and facile casting method. In this proposed work, the membrane prepared was used for removal of organic textile dyes from their aqueous solutions. The as-synthesized PVA/CS-MNP membrane was examined using different analytical techniques such as Fourier transform infrared spectroscopy (FTIR) and field emission scanning electron microscopy (FESEM), and mechanical properties of material was also studied. Two cationic dyes, methylene blue (MB) and eosin yellow (EY), were chosen as template dyes to be removed from industrial waste water. These dyes were degraded by carrying out a reaction in which the synthesized membrane was used as a photocatalyst. The study of kinetics revealed that the reaction process followed pseudo-first-order kinetics. The efficiency of catalyst and the rate of reaction were also examined by varying parameters such as pH, initial concentration of dyes, and composition of membrane. The maximum efficiency of catalyst was observed at pH 12 as more than 95% of dyes degraded within 1 h of time span. The catalyst was found to be reusable as its efficiency did not deteriorate even after using it for several times. Such functional membrane having higher stability, low production cost, excellent efficiency to degrade dyes, and good recyclability are promising material for distinctly effective deletion of organic dyes from waste water.

Fabrication of untreated and silane-treated carboxylated cellulose nanocrystals and their reinforcement in natural rubber biocomposites

In this study, cellulose nanocrystal (CNC) was extracted from Napier grass stems and subsequently functionalized to carboxylated cellulose nanocrystal (XCNC) by using an environmentally friendly method, namely, the KMnO₄/oxalic acid redox reaction. The XCNC was subsequently modified with triethoxyvinylsilane (TEVS), called VCNC, by using ultrasound irradiation. The characterization of the prepared XCNC and VCNC was performed. The needle-like shape of XCNC was observed with an average diameter and length of 11.5 and 156 nm, respectively. XCNC had a carboxyl content of about 1.21 mmol g^-1. The silane treatment showed no significant effects on the diameter and length of XCNC. When incorporated into natural rubber (NR), both XCNC and VCNC showed very high reinforcement, as evidenced by the substantial increases in modulus and hardness of the biocomposites, even at very low filler loadings. However, due to the high polarity of XCNC, tensile strength was not significantly improved with increasing XCNC loading up to 2 phr, above which it decreased rapidly due to the filler agglomeration. For VCNC, the silane treatment reduced hydrophilicity and improved compatibility with NR. The highly reactive vinyl group on the VCNC's surface also takes part in sulfur vulcanization, leading to the strong covalent linkages between rubber and VCNC. Consequently, VCNC showed better reinforcement than XCNC, as evidenced by the markedly higher tensile strength and modulus, when compared at an equal filler loading. This study demonstrates the achievement in the preparation of a highly reinforcing bio-filler (VCNC) for NR from Napier grass using an environmentally friendly method and followed by a quick and simple sonochemical method.

Fabrication of electrospun Mondia whitei/PVA nanofibres: application in the removal of acidic drugs

Novel electrospun Mondia whitei/PVA blend nanofibres were fabricated for potential water treatment applications by blending a natural polymer extracted from Mondia whitei (MW) roots with poly (vinyl alcohol) (PVA). The fabricated nanofibres were shown to have a smooth and uniform morphology with an average diameter of 99 ± 0.025 nm. The FTIR, XPS, XRD, and TGA characterisation results indicated changes in functional groups, crystallinity, and thermal stability of the Mondia whitei/PVA blend nanofibres, as compared to the original material. This finding confirmed that the polymers interacted through hydrogen bonding of MW and hydroxyl groups of PVA. The performance of the fabricated nanofibres was investigated for the removal of acidic drugs from spiked water samples. Factors (concentration of acidic drugs, dosage of the nanofibers and contact time) which affect the removal efficiency of the nanofibres were optimised using ultrapure water. Using the nanofibres, 100% removal efficiency for acidic drugs (aspirin, ketoprofen, fenoprofen, diclofenac, and ibuprofen) was achieved. The removal efficiency of the influent wastewater was 76, 89, 97, 93 and 94% for aspirin, ketoprofen, fenoprofen, diclofenac and ibuprofen, respectively, while the removal efficiency of the effluent was 86, 96, 97, 97 and 95% for aspirin, ketoprofen, fenoprofen, diclofenac and ibuprofen, respectively.

Novel Physically Cross-Linked Curcumin-Loaded PVA/Aloe vera Hydrogel Membranes for Acceleration of Topical Wound Healing: In Vitro and In Vivo Experiments

This study aims to prepare novel cross-linked antimicrobial membranes composed of PVA-Aloe vera hydrogels using novel physically cross-linked method via transforming PVA to high crystalline structure using propanol. Curcumin was incorporated to improve the membrane biological properties; while gentamycin improved sharply antimicrobial properties. PVA-Aloe vera hydrogel membranes were analyzed by FTIR, SEM, XRD and TGA measurements for characterizing resultant cross-linked membranes. Physicochemical measurements, e.g., swelling and mechanical stability were assessed for further studying the dressings. Antibacterial activity of cross-linked PVA-Aloe vera-curcumin membranes was tested using five bacterial strains. Results showed that high Aloe vera content in cross-linked membranes has insignificant impact on the release of gentamicin. Adult Wister Albino rats were used to test membrane’s ability for improving the wound healing rate in vivo. In vivo findings showed that PVA/Aloe vera/curcumin membranes dramatically reduced the size of mouse full-thickness wounds, as indicated by a decrease in the wound size. Furthermore, histological tests of wounds dressed with membranes revealed a significant re-epithelialization; compared to wounds treated with cotton gauze and PVA/Aloe vera dressings without curcumin, showing curcumin’s efficacy. These results refer to PVA-Aloe vera-curcumin membrane has exceptional wound healing and skin regeneration capacity.

Enteromorpha cellulose micro-nanofibrils/poly(vinyl alcohol) based composite films with excellent hydrophilic, mechanical properties and improved thermal stability

This study presents the preparation of cellulose micro-nanofibrils (CMNFs) from Enteromorpha (EP) and the application in PVA/acetylated distarch phosphate (ADSP)/CMNFs composite films. The Micro-nano scale, hydrophilicity, and strong hydrogen bond characteristics of CMNFs prepared form EP by acid hydrolysis were confirmed through the granular statistics, XRD analysis and chemical structure analysis. With the addition of CMNFs, the ultimate tensile strength and elongation at break of composite films are increased by 42.4 % and 90.3 %. An original Weibull statistical analysis shows the impact of CMNFs' added amount on strength distribution and ultimate stress. SEM and polarizing microscope images show the CMNFs' dispersion state in that films is optimal, when their addition was to be 2 %-3 % of total dry weight of PVA/ADSP matrix， which is consistent with the results of Weibull modulus analysis. The main thermal weight-loss process of the composite film is divided into four stages, CMNFs can significantly increase the thermostability at 280 °C to 400 °C. The experiment of water contact angle and water vapor transmission rate of the composite films confirmed that CMNFs can improve films' hydrophilicity. This study provides basis for the preparation of hydrophilic CMNFs and mechanism of modification study PVA-based composites.

Exploration of multifunctional properties of garlic skin derived cellulose nanocrystals and extracts incorporated chitosan biocomposite films for active packaging application

For many years, garlic has been used as a condiment in food and traditional medicine. However, the garlic skin, which accounts for 25% of the garlic bulk, is considered agricultural waste. In this study, cellulose nanocrystals (CNCs) and garlic extract (GE) from garlic skin were isolated and used as fillers to manufacture biocomposite films. The films were characterized in terms of UV barrier, thermal, mechanical, biodegradability, and antimicrobial activity. The chitosan-containing films and CNCs have significantly improved the films' tensile strength, Young's modulus, and elongation but decreased the film transparency compared to chitosan films. The combination of the CNCs and GE, on the other hand, slightly reduced the mechanical properties. The addition of CNCs slightly decreased the film transparency, while the addition of GE significantly improved the UV barrier properties. Thermal studies revealed that the incorporation of CNC and GE had minimal effect on the thermal stability of the chitosan films. The degradability rate of the chitosan composite films was found to be higher than that of the neat chitosan films. The antimicrobial properties of films were studied against Escherichia coli, Streptomyces griseorubens, Streptomyces alboviridis, and Staphylococcus aureus, observing that their growth was considerably inhibited by the addition of GE in composite films. Films incorporating both CNCs and GE from garlic skin hold more promise for active food packaging applications due to a combination of enhanced physical characteristics and antibacterial activity.

Nanocellulose-based membrane as a potential material for high performance biodegradable aerosol respirators for SARS-CoV-2 prevention: a review

The controversy surrounding the transmission of COVID-19 in 2020 has revealed the need to better understand the airborne transmission route of respiratory viruses to establish appropriate strategies to limit their transmission. The effectiveness in protecting against COVID-19 has led to a high demand for face masks. This includes the single-use of non-degradable masks and Filtering Facepiece Respirators by a large proportion of the public, leading to environmental concerns related to waste management. Thus, nanocellulose-based membranes are a promising environmental solution for aerosol filtration due to their biodegradability, renewability, biocompatibility, high specific surface area, non-toxicity, ease of functionalization and worldwide availability. Although the technology for producing high-performance aerosol filter membranes from cellulose-based materials is still in its initial stage, several promising results show the prospects of the use of this kind of materials. This review focuses on the overview of nanocellulose-based filter media, including its processing, desirable characteristics and recent developments regarding filtration, functionalization, biodegradability, and mechanical behavior. The porosity control, surface wettability and surface functional groups resulting from the silylation treatment to improve the filtration capacity of the nanocellulose-based membrane is discussed. Future research trends in this area are planned to develop the air filter media by reinforcing the filter membrane structure of CNF with CNCs. In addition, the integration of sol-gel technology into the production of an air filter can tailor the pore size of the membrane for a viable physical screening solution in future studies.

Extraction of cellulose nanocrystals from areca waste and its application in eco-friendly biocomposite film

Areca nut husk fibers are easily available and they are abundant agricultural waste, whose utilization to high value products needs more attention. The present study aims at the extraction of cellulose nanocrystals (CNCs) from areca nut husk fibers and the evaluation of its reinforcement capacity in polyvinyl alcohol (PVA) and chitosan (CS) film. The CNC showed rod-like structures, which were confirmed by TEM and AFM analysis. The diameter of the isolated CNC was 19 ± 3.3 nm; the length was about 195 ± 24 nm with an aspect ratio of 10.2 ± 6.8. The zeta potential of CNC was -15.3 ± 1.2 mV. Fourier Transform Infrared Spectroscopy analysis showed that the non-cellulosic compounds were effectively eliminated, and the X-ray diffraction results showed that CNC had higher crystallinity than the raw, alkali, and the bleached fibers. Thermogravimetric analysis revealed good thermal stability for the CNC. Moreover, the effects of the incorporation of CNC on the optical and tensile behaviours of the bionanocomposite film were investigated. The bionanocomposite film retained the same transparency as the PVA/CS film, indicating that the CNC was disseminated evenly in the film. The incorporation of CNC (3 wt%) to the PVA/CS film enhanced the tensile strength of the bionanocomposite film (9.46 ± 1.6 MPa) when compared to the control films (7.81 ± 1.4 MPa). Furthermore, the prepared nanobiocomposite film exhibited good antimicrobial activity against foodborne pathogenic bacteria and postharvest pathogenic fungi. These findings suggest that the bionanocomposite film might be suitable for food packaging applications.

Effect of Length of Cellulose Nanofibers on Mechanical Reinforcement of Polyvinyl Alcohol

Cellulose nanofibers (CNF), representing the nano-structured cellulose, have attained an extensive research attention due to their sustainability, biodegradability, nanoscale dimensions, large surface area, unique optical and mechanical performance, etc. Different lengths of CNF can lead to different extents of entanglements or network-like structures through van der Waals forces. In this study, a series of polyvinyl alcohol (PVA) composite films, reinforced with CNF of different lengths, were fabricated via conventional solvent casting technique. CNF were extracted from jute fibers by tuning the dosage of sodium hypochlorite during the TEMPO-mediated oxidation. The mechanical properties and thermal behavior were observed to be significantly improved, while the optical transparency decreased slightly (Tr. > 75%). Interestingly, the PVA/CNF20 nanocomposite films exhibited higher tensile strength of 34.22 MPa at 2 wt% filler loading than the PVA/CNF10 (32.55 MPa) while displayed higher elastic modulus of 482.75 MPa than the PVA/CNF20 films (405.80 MPa). Overall, the findings reported in this study provide a novel, simple and inexpensive approach for preparing the high-performance polymer nanocomposites with tunable mechanical properties, reinforced with an abundant and renewable material.

Properties of Biocomposite Film Based on Whey Protein Isolate Filled with Nanocrystalline Cellulose from Pineapple Crown Leaf

Among the main bio-based polymer for food packaging materials, whey protein isolate (WPI) is one of the biopolymers that have excellent film-forming properties and are environmentally friendly. This study was performed to analyse the effect of various concentrations of bio-based nanocrystalline cellulose (NCC) extracted from pineapple crown leaf (PCL) on the properties of whey protein isolate (WPI) films using the solution casting technique. Six WPI films were fabricated with different loadings of NCC from 0 to 10 % w/v. The resulting films were characterised based on their mechanical, physical, chemical, and thermal properties. The results show that NCC loadings increased the thickness of the resulting films. The transparency of the films decreased at higher NCC loadings. The moisture content and moisture absorption of the films decreased with the presence of the NCC, being lower at higher NCC loadings. The water solubility of the films decreased from 92.2% for the pure WPI to 65.5% for the one containing 10 % w/v of NCC. The tensile strength of the films peaked at 7% NCC loading with the value of 5.1 MPa. Conversely, the trend of the elongation at break data was the opposite of the tensile strength. Moreover, the addition of NCC produced a slight effect of NCC in FTIR spectra of the WPI films using principal component analysis. NCC loading enhanced the thermal stability of the WPI films, as shown by an increase in the glass transition temperature at higher NCC loadings. Moreover, the morphology of the films turned rougher and more heterogeneous with small particle aggregates in the presence of the NCC. Overall, the addition of NCC enhanced the water barrier and mechanical properties of the WPI films by incorporating the PCL-based NCC as the filler.

Preparation and characterization of a novel hamada scoparia polysaccharide composite films and evaluation of their effect on cutaneous wound healing in rat

This work was intended to prepare biodegradable and edible films from polysaccharide extracted from Hammada scoparia leaves (named PSP) and reinforced by poly (vinyl alcohol) (PVA). Four films with different ratios of PSP/PVA: P1 (70:30), P2 (50:50), FP3 (30:70) and pure PVA (100 % PVA) were prepared and characterized in terms of structural (FT-IR), physical (Thickness, solubility and swelling index), optical and thermal properties (TGA). The antioxidant activities of different films were determined in vitro and evaluated in vivo through the examination of wound healing capability. Data revealed that the film P1 displayed the highest antioxidant activity in vitro and accelerated significantly the wound healing, after sixteen days of treatment, attested by higher wound appearance scores and a higher content of collagen (765.924 ± 4.44 mg/g of tissue) confirmed by histological examination, when compared with control, CYTOL CENTELLA® and pure PVA-treated groups. Overall, these results demonstrated that PSP/PVA based films exhibited a higher wound healing potential confirmed with the high antioxidant activities in vitro.

Hybrid Composite Membrane of Phosphorylated Chitosan/Poly (Vinyl Alcohol)/Silica as a Proton Exchange Membrane

Chitosan is one of the natural biopolymers that has been studied as an alternative material to replace Nafion membranes as proton change membranes. Nevertheless, unmodified chitosan membranes have limitations including low proton conductivity and mechanical stability. The aim of this work is to study the effect of modifying chitosan through polymer blending with different compositions and the addition of inorganic filler on the microstructure and physical properties of N-methylene phosphonic chitosan/poly (vinyl alcohol) (NMPC/PVA) composite membranes. In this work, the NMPC biopolymer and PVA polymer are used as host polymers to produce NMPC/PVA composite membranes with different compositions (30-70% NMPC content). Increasing NMPC content in the membranes increases their proton conductivity, and as NMPC/PVA-50 composite membrane demonstrates the highest conductivity (8.76 × 10-5 S cm-1 at room temperature), it is chosen to be the base membrane for modification by adding hygroscopic silicon dioxide (SiO2) filler into its membrane matrix. The loading of SiO2 filler is varied (0.5-10 wt.%) to study the influence of filler concentration on temperature-dependent proton conductivity of membranes. NMPC/PVA-SiO2 (4 wt.%) exhibits the highest proton conductivity of 5.08 × 10-4 S cm-1 at 100 °C. In conclusion, the study shows that chitosan can be modified to produce proton exchange membranes that demonstrate enhanced properties and performance with the addition of PVA and SiO2.

Eugenol-Containing Essential Oils Loaded onto Chitosan/Polyvinyl Alcohol Blended Films and Their Ability to Eradicate Staphylococcus aureus or Pseudomonas aeruginosa from Infected Microenvironments

Chronic wounds (CW) create numerous entryways for pathogen invasion and prosperity, further damaging host tissue and hindering its remodeling and repair. Essential oils (EOs) exert quick and efficient antimicrobial (AM) action, unlikely to induce bacterial resistance. Cinnamon leaf and clove oils (CLO and CO) display strong AM activity, namely against Staphylococcus aureus and Pseudomonas aeruginosa. Chitosan (CS) is a natural and biodegradable cationic polysaccharide, also widely known for its AM features. CS and poly (vinyl alcohol) (PVA) films were prepared (ratio 30/70 w/w; 9 wt%) by the solvent casting and phase inversion method. The film's thermal stability and chemical composition data reinforced polymer blending and EO entrapment. Films were supplemented with 1 and 10 wt% of EO in relation to total polymeric mass. The film thickness and degree of swelling (DS) tended to increase with EO content, particularly with 10 wt % CLO (* p < 0.05). UV-visible absorbance scans in the 250-320 cm^-1 region confirmed the successful uptake of CLO and CO into CS/PVA films, particularly with films loaded with 10 wt% EO that contained 5.30/5.32 times more CLO/CO than films supplemented with 1 wt% EO. AM testing revealed that CS films alone were effective against both bacteria and capable of eradicating all P. aeruginosa within the hour (*** p < 0.001). Still, loaded CS/PVA films showed significantly improved AM traits in relation to unloaded films within 2 h of contact. This study is a first proof of concept that CLO and CO can be dispersed into CS/PVA films and show bactericidal effects, particularly against S. aureus, this way paving the way for efficient CW therapeutics.

Nanocellulose in food packaging: A review

The research in eco-friendly and sustainable materials for packaging applications with enhanced barrier, thermo-mechanical, rheological and anti-bacterial properties has accelerated in the last decade. Last decade has witnessed immense interest in employing nanocellulose (NC) as a sustainable and biodegradable alternative to the current synthetic packaging barrier films. This review article gathers the research information on NC as a choice for food packaging material. It reviews on the employment of NC and its various forms including its chemico-physical treatments into bio/polymers and its impact on the performance of nanocomposites for food packaging application. The review reveals the fact that the research trends towards NC based materials are quite promising for Active Packaging (AP) applications, including the Controlled Release Packaging (CRP) and Responsive Packaging (RP). Finally, it summarizes with the challenges of sustainable packaging, gray areas that need an improvement/focus in order to commercially exploit this wonderful material for packaging application.

Isolation and characterization of micro and nanocrystalline cellulose fibers from the walnut shell, corncob and sugarcane bagasse

The present study aims to extract and characterize the microcrystalline cellulose (MCC) present in different agro-industrial wastes such as walnut shells, corncob, and sugarcane bagasse. Moreover, it is also the aim of this study to convert MCCs to nanocrystalline cellulose fiber (NCCF), to demonstrate the difference in morphological, structural, thermal, and chemical natures. Corncob cellulose was observed to possess a loosely bounded linear bundle structure. Nanocrystalline cellulose fiber yield from walnut shell and sugarcane bagasse cellulose were higher than corncob cellulose. The thermal stability of cellulose was noted to be high for walnut shell NCCF. Nanocrystalline cellulose fiber of corncob and sugarcane bagasse was estimated to have a low thermal degradation temperature. All the MCCs and NCCFs produced from investigated cellulose sources were found to have type I cellulose. Functional group compositions of cellulose were observed to be intact for converted agro-based NCCF's.

Effects of cellulose nanofibrils/graphene oxide hybrid nanofiller in PVA nanocomposites

NCF/GO hybrid nanofillers with excellent UV-shielding properties were prepared by using TEMPO-oxidized nanocellulose fibrils (NCF) and graphene oxide (GO) as raw materials; different mass ratios of NCF to GO (2: 1, 4: 1, 8: 1, and 16: 1) were used. The NCF and GO were then combined and used as a hybrid filler to study the synergistic effects on polyvinyl alcohol (PVA) nanocomposites. With 5% hybrid nanofiller, the UV-shielding performance of the PVA/NCF/GO composite film was higher than 90%. The tensile strength and Young's modulus of the PVA/CG-2 composite film increased by 74.5% and 278.0%, respectively, and the water absorption decreased by 59%. Moreover, the thermal stabilities of the nanocomposites also improved. This synergistic effect improved the performance of the hybrid nanofiller by avoiding the agglomeration of nanofillers in the polymer matrix and improving the homogeneity of the dispersion. The synergistic effect between the fillers provides a new idea for the preparation of novel multifunctional nanocomposites.

Review of Chitosan-Based Polymers as Proton Exchange Membranes and Roles of Chitosan-Supported Ionic Liquids

Perfluorosulphonic acid-based membranes such as Nafion are widely used in fuel cell applications. However, these membranes have several drawbacks, including high expense, non-eco-friendliness, and low proton conductivity under anhydrous conditions. Biopolymer-based membranes, such as chitosan (CS), cellulose, and carrageenan, are popular. They have been introduced and are being studied as alternative materials for enhancing fuel cell performance, because they are environmentally friendly and economical. Modifications that will enhance the proton conductivity of biopolymer-based membranes have been performed. Ionic liquids, which are good electrolytes, are studied for their potential to improve the ionic conductivity and thermal stability of fuel cell applications. This review summarizes the development and evolution of CS biopolymer-based membranes and ionic liquids in fuel cell applications over the past decade. It also focuses on the improved performances of fuel cell applications using biopolymer-based membranes and ionic liquids as promising clean energy.

Chitosan Hydrogels Crosslinked by Genipin and Reinforced with Cellulose Nanocrystals: Production and Characterization

In this work, chitosan hydrogels crosslinked with genipin and reinforced with cellulose nanocrystals (CNC) were developed and characterized with the aim of future biomedical applications. CNC was produced by acid hydrolysis and characterized by atomic force microscopy (AFM). Chitosan/CNC nanocomposite hydrogels were produced with different CNC concentrations (w/w): 0%, 2%, 4%, and 6%. The genipin was used as a crosslinking agent in a genipin/chitosan molar proportion of 1:8. The hydrogels were characterized by porosity measurements, scanning electron microscopy (SEM), swelling test, and mechanical compression test. No significant differences were observed concerning the porosity of the hydrogels; however, a trend of decreasing porosity was observed with increasing CNC content. The SEM images showed a better pore structure as the CNC concentration increased. A decrease in the swelling degree with increasing CNC content in the chitosan/CNC nanocomposite hydrogel was verified in the swelling tests. An increase in the CNC concentration in the chitosan/CNC nanocomposite hydrogel caused a gradual increase in the maximum stress and maximum strain as observed in the compression tests, showing a significant difference between chitosan/CNC 6 wt % and neat chitosan hydrogel.

Preparation and Characterization of Microcellulose and Nanocellulose Fibers from Artemisia Vulgaris Bast

Artemisia vulgaris is an economic plant that is spreading widely in central China. Its unused bast generates a large amount of biomass waste annually. Utilizing the fibers in Artemisia vulgaris bast may provide a new solution to this problem. This research attempts to strengthen the understanding of Artemisia vulgaris by analyzing its fiber compositions and preparing micro- and nano-cellulose fibers, which can be used as raw materials for composites. In this work, Artemisia vulgaris bast powder (AP) and microcellulose and nanocellulose fibers (AMFs and ANFs) were produced and characterized by optical microscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TG), and bacteriostatic test. The results indicated that cellulose, hemicellulose, and lignin were the main components in the Artemisia vulgaris bast. The cellulose content reached 40.9%. The Artemisia vulgaris single fibers were microcellulose fibers with an average length of 850.6 μm and a diameter of 14.4 μm. Moreover, the AMF had considerable antibacterial ability with an antibacterial ratio of 36.6%. The ANF showed a length range of 250-300 nm and a diameter of 10-20 nm, and it had a higher crystallinity (76%) and a lower thermal stability (initial degradation temperature of 183 °C) compared with raw ANF (233 °C). This study provides fundamental information on Artemisia vulgaris bast cellulose for its subsequent utilization.

Thermal conductivity enhancement in electrospun poly(vinyl alcohol) and poly(vinyl alcohol)/cellulose nanocrystal composite nanofibers

The thermal conductivity enhancement of neat poly(vinyl alcohol) and poly(vinyl alcohol) (PVA)/cellulose nanocrystal (CNC) composite was attempted via electrospinning. The suspended microdevice technique was applied to measure the thermal conductivity of electrospun nanofibers (NFs). Neat PVA NFs and PVA/CNC NFs with a diameter of approximately 200 nm showed thermal conductivities of 1.23 and 0.74 W/m-K, respectively, at room temperature, which are higher than that of bulk PVA by factors of 6 and 3.5, respectively. Material characterization by Fourier transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis confirmed that the thermal conductivity of the PVA/CNC NFs was enhanced by the reinforcement of their backbone rigidity, while that of the neat PVA NFs was attributed to the increase in their crystallinity that occurred during the electrospinning.

Cellulose Nanofiber-Reinforced Chitosan Hydrogel Composites for Intervertebral Disc Tissue Repair

The development of non-cellularized composites of chitosan (CHI) hydrogels, filled with cellulose nanofibers (CNFs) of the type nanofibrillated cellulose, was proposed for the repair and regeneration of the intervertebral disc (IVD) annulus fibrosus (AF) tissue. With the achievement of CNF-filled CHI hydrogels, biomaterial-based implants were designed to restore damaged/degenerated discs. The structural, mechanical and biological properties of the developed hydrogel composites were investigated. The neutralization of weakly acidic aqueous CNF/CHI viscous suspensions in NaOH yielded composites of physical hydrogels in which the cellulose nanofibers reinforced the CHI matrix, as investigated by means of microtensile testing under controlled humidity. We assessed the suitability of the achieved biomaterials for intervertebral disc tissue engineering in ex vivo experiments using spine pig models. Cellulose nanofiber-filled chitosan hydrogels can be used as implants in AF tissue defects to restore IVD biomechanics and constitute contention patches against disc nucleus protrusion while serving as support for IVD regeneration.

Preparation and characterization of cellulose nanofibrils from coconut coir fibers and their reinforcements in biodegradable composite films

Coconut waste husks were effectively utilized in this study as a promising cellulose source for production of purified coir cellulose (PCC) after multiple treatments, e.g., ultrasonic-assisted solvent immersion, alkaline treatment, bleaching, etc. As to upgrade the self-value of coir cellulose based products and further broaden their applications in light of biorefinery, coir cellulose nanofibrils (CCNF) with an average diameter of 5.6 ± 1.5 nm were prepared by selection of a milder TEMPO-mediated oxidation system (TEMPO/NaClO/NaClO₂, pH = 4.8) accompanied by subsequent ultrasonic treatment. The cellulose nanofibrils were comprehensively characterized in terms of their functional groups, crystallinity, morphology, and thermal stability. The potential reinforcement of CCNFs as a filler for biodegradable PVA based films was investigated and the main properties including tensile strength, elongation at break, and thermal stability of CCNF/PVA composite films were significantly enhanced especially when 3% of CCNF (based on dry film weight) was applied.

Cellulose Nanocrystals (CNCs) Induced Crystallization of Polyvinyl Alcohol (PVA) Super Performing Nanocomposite Films

This study is aimed to explore the properties of cellulose nanocrystals (CNC)/polyvinyl alcohol (PVA) composite films with and without 1,2,3,4-butane tetracarboxylic acid (BTCA), a nontoxic crosslinker. CNC and CNC-PVA nanocomposite films are prepared using solution-casting technique. Differential scanning calorimetry (DSC) analyses show that crosslinking increased the glass transition temperature but reduced the melting temperature and crystallinity. Furthermore, high CNC concentrations in the PVA matrix interfere with PVA crystallinity, whereas in specific ratio between CNC and PVA, two different crystalline structures are observed within the PVA matrix. Film surfaces and fracture topographies characterized using scanning electron microscope indicate that at certain CNC-PVA ratios, micron-sized needle-like crystals have formed. These crystalline structures correlate with the remarkable improvement in mechanical properties of the CNC-PVA nanocomposite films, that is, enhanced tensile strain and toughness to 570% and 202 MJ m-3 , respectively, as compared to pristine PVA. BTCA enhances the tensile strain, ultimate tensile stress, toughness, and modulus of CNC films compared to pristine CNC films. Water absorption of crosslinked CNC and CNC-PVA nanocomposite films is significantly reduced, while film transparency is significantly improved as a function of PVA and crosslinker content. The presented results indicate that CNC-PVA nanocomposite films may find applications in packaging, and though materials applications.

High-Strength Antibacterial Chitosan-Cellulose Nanocrystal Composite Tissue Paper

A heightened need to control the spread of infectious diseases prompted the current work in which functionalized and innovative antimicrobial tissue paper was developed with a hydrophobic spray-coating of chitosan (Ch) and cellulose nanocrystals (CNCs) composite. It was hypothesized that the hydrophobic nature of chitosan could be counterbalanced by the addition of CNC to maintain fiber formation and water absorbency. Light-weight tissue handsheets were prepared, spray-coated with Ch, CNC, and their composite coating (ChCNC), and tested for antimicrobial activity against Gram-negative bacteria Escherichia coli and a microbial sample from a human hand after using the rest room. Water absorption and strength properties were also analyzed. To activate the surface of cationized tissue paper, an oxygen/helium gas atmospheric plasma treatment was employed on the best performing antimicrobial tissue papers. The highest bactericidal activity was observed with ChCNC-coated tissue paper, inhibiting up to 98% microbial growth. Plasma treatment further improved the antimicrobial activity of the coatings. Water absorption properties were reduced with Ch but increased with CNC. This "self-disinfecting" bactericidal tissue has the potential to be one of the most innovative products for the hygiene industry because it can dry, clean, and resist the infection of surfaces simultaneously, providing significant societal benefits.

Plasma surface-modification of cellulose nanocrystals: a green alternative towards mechanical reinforcement of ABS

This article proposes a strategy to functionalize cellulose nanocrystals by means of plasma-surface modification utilizing monomers of different nature: caprolactone, styrene and farnesene. The surface characteristics of the nanocrystals were studied by different techniques including XPS, FTIR and STEM, demonstrating that this technique allows a successful functionalization, yielding homogenous functionalization which does not alter the rod-like shape of the nanocrystals, and therefore their anisotropic behavior. We have furthermore studied the employment of the modified nanocrystals as reinforcement additive of ABS, which significantly enhanced the impact resistance of the thermoplastic, which could have great implications for industrial applications.

This article deals with the plasma-surface modification of cellulose nanocrystals and their employment as reinforcement additive of ABS.

Water-soluble polymeric xenobiotics - Polyvinyl alcohol and polyvinylpyrrolidon - And potential solutions to environmental issues: A brief review

This paper describes a potential environmental problem closely linked with the global production of water-soluble polymers such as polyvinyl alcohol (PVA) and polyvinylpyrrolidone (PVP). Both polymers make up the components of a multitude of products commonly utilized by industries and households. Hence, such a widespread use of PVA and PVP in the industrial sector and among consumers (the concentration of PVP in urban wastewater is approximately 7 mg/L) could pose a considerable problem, particularly to the environment. To this end, many publications have recently highlighted the poor biodegradability of PVA, in principle influenced by numerous biotic and abiotic factors. Facts published on the environmental fate of PVP have been scant, basically reporting that it is a biologically resistant polymer. As a result, the commercially produced water-soluble polymers of PVA and PVP are essentially non-biodegradable and possess the capacity to accumulate in virtually all environmental media. Consequently, there is a chance of heightened risk to the very environmental constituents in which PVA and PVP accumulate, depending on the routes of entry and transformation processes underway in such constituents of the ecosystem. This assumption is confirmed by the findings of initial research, which is worrying. Herein, PVA was detected in a soil environment, while a relatively high concentration of PVP was found in river water. A review of the literature was conducted to summarize the current state of knowledge concerning the fate of PVA and PVP in various environments, thereby also discerning potential solutions to tackle such dangers. This paper proposes methods to enhance the biodegradability of materials containing such materials; for PVA this means utilizing a suitable polysaccharide, whereas for PVP this pertains to actuating applications that induce substances to degrade. Accordingly, while it is understandable that this work cannot fully address all the issues associated with polymeric xenobiotics, it can still serve as a guide to discerning an economically viable solution, and provide a foundation for further research.