A Novel Cell Design for the Improved Stripping Voltammetric Detection of Zn(II), Cd(II), and Pb(II) on Commercial Screen-Printed Strips by Bismuth Codeposition in Stirred Solutions

Bismuth Film along with dsDNA-Modified Electrode Surfaces as Promising (bio)Sensors in the Analysis of Heavy Metals in Soils

Heavy metals constitute pollutants that are particularly common in air, water, and soil. They are present in both urban and rural environments, on land, and in marine ecosystems, where they cause serious environmental problems since they do not degrade easily, remain almost unchanged for long periods, and bioaccumulate. The detection and especially the quantification of metals require a systematic process. Regular monitoring is necessary because of seasonal variations in metal levels. Consequently, there is a significant need for rapid and low-cost metal determination methods. In this study, we compare and analytically validate absorption spectrometry with a sensitive voltammetric method, which uses a bismuth film-plated electrode surface and applies stripping voltammetry. Atomic absorption spectroscopy (AAS) represents a well-established analytical technique, while the applicability of anodic stripping voltammetry (ASV) in complicated sample matrices such as soil samples is currently unknown. This sample-handling challenge is investigated in the present study. The results show that the AAS and ASV methods were satisfactorily correlated and showed that the metal concentration in soils was lower than the limit values but with an increasing trend. Therefore, continuous monitoring of metal levels in the urban complex of a city is necessary and a matter of great importance. The limits of detection of cadmium (Cd) were lower when using the stripping voltammetry (SWASV) graphite furnace technique compared with those obtained with AAS when using the graphite furnace. However, when using flame atomic absorption spectroscopy (flame-AAS), the measurements tended to overestimate the concentration of Cd compared with the values found using SWASV. This highlights the differences in sensitivity and accuracy between these analytical methods for detecting Cd. The SWASV method has the advantage of being cheaper and faster, enabling the simultaneous determination of heavy elements across the range of concentrations that these elements can occur in Mediterranean soils. Additionally, a dsDNA biosensor is suggested for the discrimination of Cu(I) along with Cu(II) based on the oxidation peak of guanine, and adenine residues can be applied in the redox speciation analysis of copper in soil, which represents an issue of great importance.

Conductive electrospun composite fibers based on solid-state polymerized Poly(3,4-ethylenedioxythiophene) for simultaneous electrochemical detection of metal ions

Conductive composite fibers containing poly (3,4-ethylenedioxythiophene) (PEDOT) and silver nanoparticles (AgNPs) were fabricated by emulsion electrospinning of 2,5-dibromo-3,4-ethylenedioxythiophene (DBEDOT) in toluene together with aqueous solution of poly (vinyl alcohol) (PVA) and silver nanoparticles (AgNPs) in the presence of sodium dodecylsulfate followed by heat treatment at 70 °C to convert DBEDOT to conductive PEDOT via solid state polymerization (SSP). The composite fibers were characterized by scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy and thermogravimetric analysis. The PEDOT/PVA/AgNPs composite fibers deposited on a screen-printed carbon electrode (SPCE) surface exhibited good electrochemical response and was applied for simultaneous detection of heavy metal ions in a mixture, namely Zn(II), Cd(II), and Pb(II) via square wave anodic stripping voltammetry (SWASV). With added Bi⁺³ into the detection system, the bismuth film formed on the electrode allows effective alloy formation with the deposited heavy metals obtained upon reduction of the heavy metal ions, the detection of heavy metal ions after stripping was successfully accomplished with a linear range of 10-80 ppb and limits of detections (LOD) of 6, 3 and 8 ppb for Zn(II), Cd(II), and Pb(II), respectively.

Screen-Printed Technologies Combined with Flow Analysis Techniques: Moving from Benchtop to Everywhere

Screen-printed electrodes (SPEs) coupled with flow systems have been reported in recent decades for an ever-growing number of applications in modern electroanalysis, aiming for portable methodologies. The information acquired through this combination can be attractive for future users with basic knowledge, especially due to the increased measurement throughput, reduction in reagent consumption and minimal waste generation. The trends and possibilities of this set rely on the synergistic behavior that maximizes both SPE and flow analyses characteristics, allowing mass production and automation. This overview addresses an in-depth update about the scope of samples, target analytes, and analytical throughput (injections per hour, limits of detection, linear range, etc.) obtained by coupling injection techniques (FIA, SIA, and BIA) with SPE-based electrochemical detection.

Disposable sputtered-bismuth screen-printed sensors for voltammetric monitoring of cadmium and lead in atmospheric particulate matter samples

We report here the use of commercial screen-printed disposable sensors comprising a sputtered bismuth working electrode, a silver pseudo reference electrode and a carbon auxiliary electrode (whole set referred as Bi_spSPE), as a new and advantageous alternative for reliable and convenient monitoring of Cd and Pb in atmospheric particulate matter (PM10 fraction) by anodic stripping voltammetry after acid digestion. After a detailed exploration of surface composition and depth profiles of the Bi_spSPE by SEM, EDX, XPS and EIS, chemical and instrumental variables have been optimized to develop a reliable method capable of measuring Cd and Pb with detection limits of 11.8ngmL^-1 and 6.1ngmL^-1 respectively. These detection limits are useful for pollution monitoring of these elements in ambient air under the requirements of international health and environmental protection standards. The accuracy of the method was assessed by voltammetric measurements of Cd and Pb in ERM®-CZ120 Fine dust (PM10-like) and ERM® 1648a Urban Particulate Matter certified reference materials. The applicability of the method to Cd and Pb determination in real samples was demonstrated by analysis of PM10 samples from the air quality network in Extremadura, with a good correlation respect to the standard ICP-MS methodology. Our work constitutes the first reference about the use of disposable sensors based on Bi_spSPE for the determination of heavy metals in atmospheric particulate matter samples.

Multi-element determination of metals and metalloids in waters and wastewaters, at trace concentration level, using electroanalytical stripping methods with environmentally friendly mercury free-electrodes: A review

Nowadays, water is no longer regarded as an inexhaustible resource and the excessive release and proliferation of toxic metal(loid)s into aquatic environments has become a critical issue. Therefore, fast, accurate, simple, selective, sensitive and portable methodologies to detect multiple elements in natural waters is of paramount importance. Electrochemical stripping analysis is an efficient tool for trace metal(loid)s determinations and bring new prospects for answering the current environmental concerns. This review presents a survey of the advancements made between 2003 and 2016 on the development and application of non-toxic mercury free electrodes on the simultaneous analysis of metals and metalloids in waters and wastewaters by means of electroanalytical stripping techniques. The advantages, limitations, improvements and real applications of these "green" sensors are discussed from a critical point of view.

A miniaturized bismuth-based sensor to evaluate the marine organism Styela plicata bioremediation capacity toward heavy metal polluted seawater

Cadmium and lead are highly toxic heavy metals which cause a severe worldwide pollution. In addition to the toxic effect produced by the direct exposure, they can be bioconcentrated and accumulated in living organisms, including humans. Herein, a miniaturized and disposable electrochemical sensor was improved for the simultaneous detection of cadmium and lead ions to study the bioremediation of polluted seawater in presence of the filter-feeding marine organism Styela plicata. A screen-printed electrode modified in situ with a bismuth film was selected using the anodic stripping analysis as detection technique. This sensor was coupled with a portable potentiostat and the detection of cadmium and lead ions was carried out by Square Wave Anodic Stripping Voltammetry, allowing the simultaneous detection of both heavy metals at ppb level (LOD=0.3ppb for lead, 1.5ppb for cadmium). This analytical tool was then applied to assess the bioremediation capacity of S. plicata through a bioremediation experiment, in which the organism has been exposed to seawater artificially polluted with 1000ppb of Cd²⁺ and Pb²⁺. The matrix effect of both seawater and acid digested biological samples was evaluated. A bioconcentration phenomenon was observed for both heavy metals through the analysis of S. plicata tissues. In details, Pb²⁺ resulted to be about 2.5 times more bioconcentrated than Cd²⁺, giving an effective bioremediation level in seawater of 13% and 40% for Cd²⁺ and Pb²⁺, respectively. Thus, our results demonstrate the capability of S. plicata to bioremediate Cd²⁺ and Pb²⁺ polluted seawater as well as the suitability of the electrochemical sensor for contaminated marine environment monitoring and bioremediation evaluation.

Application of screen-printed carbon electrode modified with lead in stripping analysis of Cd(II)

In the work presented, a lead film electrode was prepared in situ on a screen-printed carbon support using a reversibly deposited mediator (Zn) and applied to the determination of Cd(II) by anodic stripping voltammetry. The electrochemical method for lead film formation is based on a co-deposition of a metal of interest (Pb), with a reversibly deposited zinc mediator, followed by oxidation of zinc, with additional deposition of lead at the appropriate potential. It serves to increase the density of lead particles, promoting lead film growth, and consequently helps to improve the electrochemical properties of the electrode. This was confirmed by microscopic and voltammetric studies. The obtained detection limit of Cd(II) is equal to 6.6 × 10−9 mol L−1 (−1.6 V for 180 s and then −0.95 V for 5 s). The presented procedure was successfully applied to cadmium determination in Bystrzyca River water samples.

Recent Advances in the Fabrication and Application of Screen-Printed Electrochemical (Bio)Sensors Based on Carbon Materials for Biomedical, Agri-Food and Environmental Analyses

This review describes recent advances in the fabrication of electrochemical (bio)sensors based on screen-printing technology involving carbon materials and their application in biomedical, agri-food and environmental analyses. It will focus on the various strategies employed in the fabrication of screen-printed (bio)sensors, together with their performance characteristics; the application of these devices for the measurement of selected naturally occurring biomolecules, environmental pollutants and toxins will be discussed.

A greener approach for impressive removal of As(iii)/As(v) from an ultra-low concentration using a highly efficient chitosan thiomer as a new adsorbent

Contamination of ground water with arsenic is a serious problem all over the world.

New Chitosan-Thiomer: An Efficient Colorimetric Sensor and Effective Sorbent for Mercury at Ultralow Concentration

This paper describes an innovative procedure for the fabrication of a facile colorimetric sensor in one step with thiol functional group for Hg(2+) detection at trace level. The sensor was successfully synthesized via chitosan isothiouronium salt intermediate with innocuous low cost thiourea reagent under microwave irradiation. It is an innovative green approach to achieve thiol functionalization with a high degree of substitution. Thiomer was characterized by titrimetry, FTIR, (1)H NMR, elemental analysis (CHNS), and EDX for extent of modification with detail structure. The synthesized and well characterized thiomer was screened for sensor application. The sensing solution of thiomer resulted in an instantaneous sharp color change from colorless, yellow, to brown with increase in Hg(2+) concentration. Chitosan thiomer also exhibited high sensitivity and selectivity for Hg(2+) over other possible interfering ions in aqueous media. The sensing responses were visualized quantitatively with quick response, good selectivity, high sensitivity, and a low detection limit of ∼0.465 ppb by the naked eye. The same was tested with a paper strip method for technological applications. Furthermore, the as-prepared sensors also exhibited exceptional sorption potential for Hg(2+) even from ultralow concentration aqueous solution and reduced the Hg(2+) concentration from 10 ppb to the extremely low level of ∼0.04 ppb as studied by cyclic voltammetry. Thus, the proposed method is simple, promising, and rapid without any complicated modifying step and is an economical alternative to traditional Hg(2+) sensors for rapid sensor application in environmental water samples at ppb levels.

Direct determination of cadmium and lead in pharmaceutical ingredients using anodic stripping voltammetry in aqueous and DMSO/water solutions

A new electrochemical method has been developed to detect and quantify the elemental impurities, cadmium(II) (Cd(2+)) and lead(II) (Pb(2+)), either simultaneously or individually in pharmaceutical matrices. The electro-analytical approach, involving the use of anodic stripping voltammetry (ASV) on an unmodified glassy carbon electrode, was performed in both aqueous and in a 95/5 dimethyl sulfoxide (DMSO)/water solutions, without acid digestion or dry ashing to remove organic matrices. Limits of detection (LODs) in the μg L(-1) [or parts per billion (ppb), mass/volume] range were obtained for both heavy metals - in the presence and absence of representative pharmaceutical components. To the best of our knowledge, the work demonstrates the first analysis of heavy metals in DMSO/water solutions through ASV. The strong reproducibility and stability of the sensing platform, as well as obviation of sample pretreatment show the promise of utilizing ASV as a sensitive, robust, and inexpensive alternative to inductively-coupled-plasma (ICP)-based approaches for the analysis of elemental impurities in, e.g., pharmaceutical-related matrices.

Disposable electrochemical sensor to evaluate the phytoremediation of the aquatic plant Lemna minor L. toward Pb(2+) and/or Cd(2+)

In this work a miniaturized and disposable electrochemical sensor was developed to evaluate the cadmium and lead ion phytoremediation potential by the floating aquatic macrophyte Lemna minor L. The sensor is based on a screen-printed electrode modified "in-situ" with bismuth film, which is more environmentally friendly than the mercury-based sensor usually adopted for lead and cadmium ion detection. The sensor was coupled with a portable potentiostat for the simultaneous measurement of cadmium and lead ions by stripping analysis. The optimized analytical system allows the simultaneous detection of both heavy metals at the ppb level (LOD equal to 0.3 and 2 ppb for lead and cadmium ions, respectively) with the advantage of using a miniaturized and cost-effective system. The sensor was then applied for the evaluation of Pb(2+) or/and Cd(2+) uptake by measuring the amount of the heavy metals both in growth medium and in plant tissues during 1 week experiments. In this way, the use of Lemna minor coupled with a portable electrochemical sensor allows the set up of a model system able both to remove the heavy metals and to measure "in-situ" the magnitude of heavy metal removal.

Disposable copper-based electrochemical sensor for anodic stripping voltammetry

In this work, we report the first copper-based point-of-care sensor for electrochemical measurements demonstrated by zinc determination in blood serum. Heavy metals require careful monitoring, yet current methods are too complex for a point-of-care system. Electrochemistry offers a simple approach to metal detection on the microscale, but traditional carbon, gold (Au), or platinum (Pt) electrodes are difficult or expensive to microfabricate, preventing widespread use. Our sensor features a new low-cost electrode material, copper, which offers simple fabrication and compatibility with microfabrication and PCB processing, while maintaining competitive performance in electrochemical detection. Anodic stripping voltammetry of zinc using our new copper-based sensors exhibited a 140 nM (9.0 ppb) limit of detection (calculated) and sensitivity greater than 1 μA/μM in the acetate buffer. The sensor was also able to determine zinc in a bovine serum extract, and the results were verified with independent sensor measurements. These results demonstrate the advantageous qualities of this lab-on-a-chip electrochemical sensor for clinical applications, which include a small sample volume (μL scale), reduced cost, short response time, and high accuracy at low concentrations of analyte.

Zinc Detection in Serum by Anodic Stripping Voltammetry on Microfabricated Bismuth Electrodes

Zinc (Zn) homeostasis is required for a functional immune system. Critically ill patients often exhibit decreased Zn serum concentrations and could potentially benefit from Zn supplementation as a therapeutic strategy. However, the conventional approaches to monitoring Zn are time consuming and costly. This work reports on detection of Zn by anodic stripping voltammetry (ASV) on bismuth electrodes in a microfabricated electrochemical cell. The working potential window of the electrodeposited bismuth film electrode was investigated by cyclic voltammetry, while square wave ASV was used for measuring Zn in acetate buffer and blood serum. Conditions critical to sensing, such as preconcentration potential, preconcentration time, and buffer pH, were optimized for Zn detection. The sensor was successfully calibrated with pH 6 acetate buffer in the physiologically-relevant range of 5 μM to 50μM Zn and exhibited well-defined and highly repeatable peaks. The sensor was used to demonstrate measurement of Zn in blood serum digested in HCl. The results of this work show that Zn detection in serum is possible with smaller sample volumes (μL vs. μL) and faster turnaround time (hours vs. days) as compared with the conventional spectroscopic methods.

Preparation of nano-sized Pb2+ imprinted polymer and its application as the chemical interface of an electrochemical sensor for toxic lead determination in different real samples

In this work, a new nano-structured ion imprinted polymer (IIP) was synthesized by copolymerization of methacrylic acid-Pb(2+) complex and ethylene glycol dimethacrylate according to the precipitation polymerization. Methacrylic acid acted as both functional monomer and complexing agent to create selective coordination sites in a cross-linked polymer. A carbon paste electrode modified with IIP-nanoparticles was used for fabrication of a Pb(2+) sensitive electrode. Differential pulse stripping voltammetry method was applied as the determination technique, after open circuit sorption of Pb(2+) on the electrode and its reduction to metallic form. The IIP modified electrode showed a considerably higher response, compared to the electrode embedded with non-imprinted polymer (NIP). This indicated that the suitable recognition sites were created in the IIP structure in the polymerization stage. Various factors, effective on the response behavior of the electrode, were investigated and optimized. The introduced sensor showed a linear range of 1.0 × 10(-9) to 8.1 × 10(-7)M and detection limit of 6.0 × 10(-10)M (S/N=3). The sensor was successfully applied for the trace lead determination in different samples.

Simultaneous Stripping Detection of Pb(II), Cd(II) and Zn(II) Using a Bimetallic Hg-Bi/Single-Walled Carbon Nanotubes Composite Electrode

A new, sensitive platform for the simultaneous electrochemical assay of Zn(II), Cd(II) and Pb(II) in aqueous solution has been developed. The platform is based on a new bimetallic Hg-Bi/single-walled carbon nanotubes (SWNTs) composite modified glassy carbon electrode (GCE), demonstrating remarkably improved performance for the anodic stripping assay of Zn(II), Cd(II) and Pb(II). The synergistic effect of Hg and Bi as well as the enlarged, activated surface and good electrical conductivity of SWNTs on GCE contribute to the enhanced activity of the proposed electrode. The analytical curves for Zn(II), Cd(II) an Pb(II) cover two linear ranges varying from 0.5 to 11 μg L(-1) and 10 to 130 μg L(-1) with correlation coefficients higher than 0.992. The limits of detection for Zn(II), Cd(II) are lower than 2 μg L(-1) (S/N = 3). For Pb(II), moreover, there is another lower, linear range from 5 to 1100 ng L(-1) with a coefficient of 0.987 and a detection limit of 0.12 ng L(-1). By using the standard addition method, Zn(II), Cd(II) and Pb(II) ions in river samples were successfully determined. These results suggest that the proposed method can be applied as a simple, efficient alternative for the simultaneous monitoring of heavy metals in water samples. In addition, this method demonstrates the powerful application of carbon nanotubes in electrochemical analysis of heavy metals.

Determination of mercury in ambient water samples by anodic stripping voltammetry on screen-printed gold electrodes

The applicability of commercial screen-printed gold electrodes (SPGEs) for the determination of Hg(II) in ambient water samples by square wave anodic stripping voltammetry has been demonstrated. Electrode conditioning procedures, chemical and instrumental variables have been optimized to develop a reliable method capable of measuring dissolved mercury in the low ng mL(-1) range (detection limit 1.1 ng mL(-1)), useful for pollution monitoring or screening purposes. The proposed method was tested with the NIST 1641d Mercury in Water Standard Reference Material (recoveries 90.0-110%) and the NCS ZC 76303 Mercury in Water Certified Reference Material (recoveries 82.5-90.6%). Waste water samples from industrial origin and fortified rain water samples were assayed for mercury by the proposed method and by a reference ICP-MS method, with good agreement. Screen printing technology thus opens a useful way for the construction of reliable electrochemical sensors for decentralized or even field Hg(II) testing.

Square wave anodic stripping voltammetry determination of eco-toxic metals in samples of biological and environmental importance

Square wave anodic stripping voltammetry was used in simultaneous determinations of eco-toxic metals (Pb, Cd, Cu and Zn) on bismuth film electrodes. The electrodes were prepared in situ on a glassy-carbon electrode (GCE) from 0.1 M acetate buffer (pH 4.5) containing 200 μg L−1 of bismuth (III), as well ex situ on electrochemically oxidized graphitized polyacrylonitrile carbon fibres from 200 mg L−1 Bi(NO3)3 in 1% HNO3 (aqueous) solution. Preparation of a Bi-modified carbon fibre electrode (CFE) was by cation exchange of Bi+3 ions for H+ of the acidic surface groups of the electro-oxidized carbon fibres, followed by electrochemical reduction to Bi0. For the Bi-GCE the linear range was 20–280 μg L−1 for zinc, 10–100 μg L−1 for lead, 10–80 μg L−1 for copper, and 5–50 μg L−1 for cadmium. For the Bi-CFE it was 20–160 μg L−1 for zinc, 10–100 μg L−1 for lead, 10–100 μg L−1 for copper, and 2–120 μg L−1 for cadmium. For both kinds of bismuth modified carbon electrodes, low limits of detection and satisfactory precision were achieved. The method was successfully applied to certified reference materials of biological (bovine liver) and environmental (mussel tissue) importance.

State-of-the-art of (bio)chemical sensor developments in analytical Spanish groups

(Bio)chemical sensors are one of the most exciting fields in analytical chemistry today. The development of these analytical devices simplifies and miniaturizes the whole analytical process. Although the initial expectation of the massive incorporation of sensors in routine analytical work has been truncated to some extent, in many other cases analytical methods based on sensor technology have solved important analytical problems. Many research groups are working in this field world-wide, reporting interesting results so far. Modestly, Spanish researchers have contributed to these recent developments. In this review, we summarize the more representative achievements carried out for these groups. They cover a wide variety of sensors, including optical, electrochemical, piezoelectric or electro-mechanical devices, used for laboratory or field analyses. The capabilities to be used in different applied areas are also critically discussed.

Electrochemical sensing in paper-based microfluidic devices

This paper describes the fabrication and the performance of microfluidic paper-based electrochemical sensing devices (we call the microfluidic paper-based electrochemical devices, microPEDs). The microPEDs comprise paper-based microfluidic channels patterned by photolithography or wax printing, and electrodes screen-printed from conducting inks (e.g., carbon or Ag/AgCl). We demonstrated that the microPEDs are capable of quantifying the concentrations of various analytes (e.g., heavy-metal ions and glucose) in aqueous solutions. This low-cost analytical device should be useful for applications in public health, environmental monitoring, and the developing world.