A multichannel native fluorescence detection system for capillary electrophoretic analysis of neurotransmitters in single neurons

Surface Environment and Energy Density Effects on the Detection and Disinfection of Microorganisms Using a Portable Instrument

Real-time detection and disinfection of foodborne pathogens are important for preventing foodborne outbreaks and for maintaining a safe environment for consumers. There are numerous methods for the disinfection of hazardous organisms, including heat treatment, chemical reaction, filtration, and irradiation. This report evaluated a portable instrument to validate its simultaneous detection and disinfection capability in typical laboratory situations. In this challenging study, three gram-negative and two gram-positive microorganisms were used. For the detection of contamination, inoculations of various concentrations were dispensed on three different surface types to estimate the performance for minimum-detectable cell concentration. Inoculations higher than 10³~10⁴ CFU/mm² and 0.15 mm of detectable contaminant size were estimated to generate a sufficient level of fluorescence signal. The evaluation of disinfection efficacy was conducted on three distinct types of surfaces, with the energy density of UVC light (275-nm) ranging from 4.5 to 22.5 mJ/cm² and the exposure time varying from 1 to 5 s. The study determined the optimal energy dose for each of the microorganisms species. In addition, surface characteristics may also be an important factor that results in different inactivation efficacy. These results demonstrate that the proposed portable device could serve as an in-field detection and disinfection unit in various environments, and provide a more efficient and user-friendly way of performing disinfection on large surface areas.

Non-enzymatic electrochemical dopamine sensing probe based on hexagonal shape zinc-doped cobalt oxide (Zn-Co2O4) nanostructure

A non-enzymatic dopamine electrochemical sensing probe was developed. A hexagonal shape zinc-doped cobalt oxide (Zn-Co₂O₄) nanostructure was prepared by a facile hydrothermal approach. The combination of Zn, which has an abundance of electrons, and Co₃O₄ exhibited a synergistically electron-rich nanocomposite. The crystallinity of the nanostructure was investigated using X-ray diffraction. A scanning electron microscope (SEM) was used to examine the surface morphology, revealing hexagonal nanoparticles with an average particle size of 400 nm. High-resolution transmission electron microscopy (HR-TEM) was used to confirm the nanostructure of the doped material. The nanostructure's bonding and functional groups were verified using Fourier transform infrared spectroscopy (FTIR). The electrochemical characterization was conducted by using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and amperometry. The resistivity of the electrode was confirmed through EIS and showed that the bare glassy carbon electrode (GCE) exhibited higher charge transfer resistance as compared to modified Zn-Co₂O₄/GCE. The sensing probe was developed by modifying the surface of GCE with Zn-Co₂O₄ nanostructure and tested as an electrochemical sensor for dopamine oxidation; it operated best at a working potential of 0.17 V (vs Ag/AgCl). The developed sensor exhibited a low limit of detection (0.002 µM), a high sensitivity (126 µA. µM^-1 cm^-2), and a wide linear range (0.2 to 185 µM). The sensor showed a short response time of < 1 s. The sensor's selectivity was investigated in the presence of coexisting species (uric acid, ascorbic acid, adrenaline, epinephrine, norepinephrine, histamine, serotonin, tyramine, phenethylamine, and glucose) with no effects on dopamine determination results. The developed sensor was also successfully used for determining dopamine concentrations in a real sample.

Recent progress in developing fluorescent probes for imaging cell metabolites

Cellular metabolites play a crucial role in promoting and regulating cellular activities, but it has been difficult to monitor these cellular metabolites in living cells and in real time. Over the past decades, iterative development and improvements of fluorescent probes have been made, resulting in the effective monitoring of metabolites. In this review, we highlight recent progress in the use of fluorescent probes for tracking some key metabolites, such as adenosine triphosphate, cyclic adenosine monophosphate, cyclic guanosine 5'-monophosphate, Nicotinamide adenine dinucleotide (NADH), reactive oxygen species, sugar, carbon monoxide, and nitric oxide for both whole cell and subcellular imaging.

Ultra-Stable UiO-66 Involved Molecularly Imprinted Polymers for Specific and Sensitive Determination of Tyramine Based on Quartz Crystal Microbalance Technology

A rapid method was developed to determine the content of tyramine in food on the basis of the combination of molecular imprinting technique and the metal-organic frameworks. We developed the new molecular imprinted polymers based on metal-organic frameworks UiO-66 (named UiO-66@MIPs) as the sensing recognition element, the non-molecular imprinted polymers based on UiO-66 (named UiO-66@NIPs) was synthesized according the same steps without tyramine for comparison. The characterization of obtained UiO-66@MIPs was investigated through a series of characterization experiments. The results indicated that the octahedral shaped UiO-66 was encapsulated in the sol-gel polymer film, with a desirable thermal stability and possessed a specific surface area (SSA) of 994.3 m²·g⁻¹. The imprinting factor of the UiO-66@MIPs for tyramine was 1.956 in static experiment. This indicates the synthesized UiO-66@MIPs have outstanding performance compered to UiO-66@NIPs on the static adsorption quantity and selective adsorption affinity. It’s to make use of advantages of the synthetic materials to develop a quartz crystal microbalance (QCM) sensor for the sensitive detection of tyramine. The detection limit of the system was 61.65 μg·L⁻¹ within measurable concentration range from 80 to 500 μg·L⁻¹. The prepared QCM sensor was verified in selectivity and application. The UiO-66@MIPs possess good behavior on selectivity, absorptivity, and chemical stability, so the UiO-66@MIPs achieve accurate and rapid trace detection of biogenic amines in food combining with the quartz crystal microbalance.

Simultaneous electrochemical detection of levodapa, paracetamol and l-tyrosine based on multi-walled carbon nanotubes

A novel electrochemical sensor for the simultaneous detection of levodopa, paracetamol and l-tyrosine was developed based on multi-walled carbon nanotubes. The sensor has the merits of wide linear range, good selectivity and good reproducibility.

Supramolecular Assembly Induced Emission of Thiazole Orange with Sulfobutylether β-cyclodextrin: A Stimuli-Responsive Fluorescence Sensor for Tyramine

Modulation and control of stimuli responsive features of molecular assemblies in organized assemblies/cavitand macrocycles have received immense attention in many areas. In this study, we have established the formation of a discrete molecular assembly of thiazole orange (TO) dyes at the portals of the sulfobutylether β-cyclodextrin (SBE₇ βCD) macrocycle leading to the evolution of a strong and distinct emission band from aggregated TO. The supramolecular assembly promoted portal aggregation of TO in its 1 : 4 (SBE₇ βCD : TO) composition, characterized by absorption, fluorescence, circular dichroism, ITC and ¹ H NMR measurements, was probed to be selectively responsive to tyramine among other biogenic amines/neurotransmitters. For the first time, the different extent of emission quenching of SBE₇ βCD : TO assembly in the presence of biogenic amines/neurotransmitters is translated to achieve a selective on-off fluorescence sensor for the detection of tyramine against other neurotransmitters with a limit-of-detection (LOD) as low as ∼575 nM (79 ppb). The emission features of the assembly with changes in temperature is found to be highly reproducible even after several temperature cycles and is promising to design an optical supramolecular thermometer in the ambient temperature range.

Design of an automated capillary electrophoresis platform for single-cell analysis

Single-cell analysis of cellular contents by highly sensitive analytical instruments is known as chemical cytometry. A chemical cytometer typically samples one cell at a time, quantifies the cellular contents of interest, and then processes and reports that data. Automation adds the potential to perform this entire sequence of events with minimal intervention, increasing throughput and repeatability. In this chapter, we discuss the design considerations for an automated capillary electrophoresis-based instrument for assay of enzymatic activity within single cells. We describe the key requirements of the microscope base and capillary electrophoresis platforms. We also provide detailed protocols and schematic designs of our cell isolation, lysis, sampling, and detection strategies. Additionally, we describe our signal processing and instrument automation workflows. The described automated system has demonstrated single-cell throughput at rates above 100cells/h and analyte limits of detection as low as 10^-20mol.

Advances in capillary electrophoresis for the life sciences

Capillary electrophoresis (CE) played an important role in developments in the life sciences. The technique is nowadays used for the analysis of both large and small molecules in applications where it performs better than or is complementary to liquid chromatographic techniques. In this review, principles of different electromigration techniques, especially capillary isoelectric focusing (CIEF), capillary gel (CGE) and capillary zone electrophoresis (CZE), are described and recent developments in instrumentation, with an emphasis on mass spectrometry (MS) coupling and microchip CE, are discussed. The role of CE in the life sciences is shown with applications in which it had a high impact over the past few decades. In this context, current practice for the characterization of biopharmaceuticals (therapeutic proteins) is shown with CIEF, CGE and CZE using different detection techniques, including MS. Subsequently, the application of CGE and CZE, in combination with laser induced fluorescence detection and CZE-MS are demonstrated for the analysis of protein-released glycans in the characterization of biopharmaceuticals and glycan biomarker discovery in biological samples. Special attention is paid to developments in capillary coatings and derivatization strategies for glycans. Finally, routine CE analysis in clinical chemistry and latest developments in metabolomics approaches for the profiling of small molecules in biological samples are discussed. The large number of CE applications published for these topics in recent years clearly demonstrates the established role of CE in life sciences.

Impedimetric sensor for tyramine based on gold nanoparticle doped-poly(8-anilino-1-naphthalene sulphonic acid) modified gold electrodes

A novel impedimetric sensor for the determination of tyramine (Tyr), a biogenic amine, on the surface of gold nanoparticle-poly-(8-anilino-1-napthalene sulphonic acid), AuNP-PANSA modified gold electrode (AuE) is presented for the first time. The AuNP were successfully synthesized by a green synthesis method. Their characterization and optimization were conducted using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, electrochemical impedance spectroscopy and cyclic voltammetry. Under optimal conditions, the impedimetric sensor revealed a relatively broad linear range from 0.8 to 80 µM similar to more complex architectures found in the literature and the limit of detection of 0.04 µM was the lowest achieved until now. In order to test the reliability of the proposed method, real sample application studies were conducted using dairy products and fermented drinks. It was found that the sensor presented a good selectivity and recovery. Furthermore, the impedimetric sensor shows good reproducibility, stability, selectivity and very small interferences which augur well for its application in food safety control processes.

Two-Dimensional Capillary Electrophoresis with On-Line Sample Preparation and Cyclodextrin Separation Environment for Direct Determination of Serotonin in Human Urine

An advanced two-dimensional capillary electrophoresis method, based on on-line combination of capillary isotachophoresis and capillary zone electrophoresis with cyclodextrin additive in background electrolyte, was developed for effective determination of serotonin in human urine. Hydrodynamically closed separation system and large bore capillaries (300–800 µm) were chosen for the possibility to enhance the sample load capacity, and, by that, to decrease limit of detection. Isotachophoresis served for the sample preseparation, defined elimination of sample matrix constituents (sample clean up), and preconcentration of the analyte. Cyclodextrin separation environment enhanced separation selectivity of capillary zone electrophoresis. In this way, serotonin could be successfully separated from the rest of the sample matrix constituents migrating in capillary zone electrophoresis step so that human urine could be directly (i.e., without any external sample preparation) injected into the analyzer. The proposed method was successfully validated, showing favorable parameters of sensitivity (limit of detection for serotonin was 2.32 ng·mL⁻¹), linearity (regression coefficient higher than 0.99), precision (repeatability of the migration time and peak area were in the range of 0.02–1.17% and 5.25–7.88%, respectively), and recovery (ranging in the interval of 90.0–93.6%). The developed method was applied for the assay of the human urine samples obtained from healthy volunteers. The determined concentrations of serotonin in such samples were in the range of 12.4–491.2 ng·mL⁻¹ that was in good agreement with literature data. This advanced method represents a highly effective, reliable, and low-cost alternative for the routine determination of serotonin as a biomarker in human urine.

Broccoli-shaped biosensor hierarchy for electrochemical screening of noradrenaline in living cells

Monitoring and determination of ultra-trace concentrations of monoamine neurotransmitter such as noradrenaline (NA) in living cells with simple, sensitive and selective assays are significantly interesting. We design NA-electrode sensing system based on C-, N-doped NiO broccoli-like hierarchy (CNNB). The spherical broccoli-head umbrella architectures associated with nano-tubular arrangements enabled to tailor NA biosensor design. The homogenous doping and anisotropic dispersion of CN nanospheres along the entire NB head nanotubes lead to creating of abundant electroactive sites in the interior tubular vessels and outer surfaces for ultrasensitive detection of NA in living cells such as PC12. The CNNB biosensor electrodes showed efficient electrocatalytic activity, enhanced kinetics for electrooxidation of NA, and fast electron-transfer between electrode-electrolyte interface surfaces, enabling synergistic enhancement in sensitivity, and selectivity at a low-detectable concentration of ∼ 6nM and reproducibility of broccoli-shaped NA-electrodes. The integrated CNNB biosensor electrodes showed evidence of monitoring and screening of NA released from PC12 cells under K⁺ ion-extracellular stimulation process. The unique features of CNNB in terms of NA-selectivity among multi-competitive components, long-term stability during the detection of NA may open their practical, in-vitro application for extracellular monoamine neurotransmitters detection in living cells.

Signals from the brainstem sleep/wake centers regulate behavioral timing via the circadian clock

Sleep-wake cycling is controlled by the complex interplay between two brain systems, one which controls vigilance state, regulating the transition between sleep and wake, and the other circadian, which communicates time-of-day. Together, they align sleep appropriately with energetic need and the day-night cycle. Neural circuits connect brain stem sites that regulate vigilance state with the suprachiasmatic nucleus (SCN), the master circadian clock, but the function of these connections has been unknown. Coupling discrete stimulation of pontine nuclei controlling vigilance state with analytical chemical measurements of intra-SCN microdialysates in mouse, we found significant neurotransmitter release at the SCN and, concomitantly, resetting of behavioral circadian rhythms. Depending upon stimulus conditions and time-of-day, SCN acetylcholine and/or glutamate levels were augmented and generated shifts of behavioral rhythms. These results establish modes of neurochemical communication from brain regions controlling vigilance state to the central circadian clock, with behavioral consequences. They suggest a basis for dynamic integration across brain systems that regulate vigilance states, and a potential vulnerability to altered communication in sleep disorders.

Large-volume sample stacking for in vivo monitoring of trace levels of γ-aminobutyric acid, glycine and glutamate in microdialysates of periaqueductal gray matter by capillary electrophoresis with contactless conductivity detection

A new variant of large-volume sample stacking injection (LVSS) was used in the capillary electrophoresis with capacitively coupled contactless conductivity detection (CE/C(4)D) determination of the neurotransmitters γ-aminobutyric acid (GABA), glycine (Gly) and glutamate (Glu) in microdialysates of periaqueductal gray matter (PAG). The separation capillary was filled to 98% from the injection side with a sample of microdialysate in acetonitrile. Simultaneously with turning on the separation voltage, the sample zone was forced out by the background electrolyte by increasing the pressure in the terminal capillary outlet vessel. As a consequence of the stacking effect, the analyte was concentrated from the large sample volume into a narrow zone at the sample/background electrolyte boundary close to the injection end of the capillary. Under these conditions, LOD values of 9, 10 and 15nM were determined in the model samples for GABA, Gly and Glu, respectively; RSD equalled 0.5% for the migration times and 1.0-1.9% for the peak areas, respectively. In analysis of microdialysates of PAG, LOD values of 29, 29 and 37nM were determined for GABA, Gly and Glu, respectively; RSD equalled 0.5-0.7% for the migration times and 2.6-8.2% for the peak areas, respectively. The determined basal levels of the neurotransmitters in PAG microdialysates are 0.08, 4.7 and 0.8μM for GABA, Gly and Glu, respectively. Carrageenan-induced hyperalgesia increases the Gly and Glu levels and reduces GABA in PAG microdialysate. Peroral administration of paracetamol in hyperalgesia effectively reduces the Gly value and has no effect on Glu and GABA.

Automated method for analysis of tryptophan and tyrosine metabolites using capillary electrophoresis with native fluorescence detection

Capillary electrophoresis (CE) with laser-induced native fluorescence (LINF) detection offers the ability to characterize low levels of selected analyte classes, depending on the excitation and emission wavelengths used. Here a new automated CE-LINF system that provides deep ultraviolet (DUV) excitation (224 nm) and variable emission wavelength detection was evaluated for the analysis of small molecule tryptophan- and tyrosine-related metabolites. The optimized instrument design includes several features that increase throughput, lower instrument cost and maintenance, and decrease complexity when compared with earlier systems using DUV excitation. Sensitivity is enhanced by using an ellipsoid detection cell to increase the fluorescence collection efficiency. The limits of detection ranged from 4 to 30 nmol/L for serotonin and tyrosine, respectively. The system demonstrated excellent linearity over several orders of magnitude of concentration and intraday precision from 1-11 % relative standard deviation (RSD). The instrument's performance was validated via tryptophan and serotonin characterization using tissue extracts from the mammalian brain stem, with RSDs of less than 10 % for both metabolites. The flexibility and sensitivity offered by DUV laser excitation and tunable emission enables a broad range of small-volume measurements.

A hyphenated optical trap capillary electrophoresis laser induced native fluorescence system for single-cell chemical analysis

Single-cell measurements allow a unique glimpse into cell-to-cell heterogeneity; even small changes in selected cells can have a profound impact on an organism's physiology. Here an integrated approach to single-cell chemical sampling and assay are described. Capillary electrophoresis (CE) with laser-induced native fluorescence (LINF) has the sensitivity to characterize natively fluorescent indoles and catechols within individual cells. While the separation and detection approaches are well established, the sampling and injection of individually selected cells requires new approaches. We describe an optimized system that interfaces a single-beam optical trap with CE and multichannel LINF detection. A cell is localized within the trap and then the capillary inlet is positioned near the cell using a computer-controlled micromanipulator. Hydrodynamic injection allows cell lysis to occur within the capillary inlet, followed by the CE separation and LINF detection. The use of multiple emission wavelengths allows improved analyte identification based on differences in analyte fluorescence emission profiles and migration time. The system enables injections of individual rat pinealocytes and quantification of their endogenous indoles, including serotonin, N-acetyl-serotonin, 5-hydroxyindole-3-acetic acid, tryptophol and others. The amounts detected in individual cells incubated in 5-hydroxytryptophan ranged from 10(-14) mol to 10(-16) mol, an order of magnitude higher than observed in untreated pinealocytes.

Sampling techniques for single-cell electrophoresis

Cells are extraordinarily complex, containing thousands of different analytes with concentrations spanning at least nine orders of magnitude. Analyzing single cells instead of tissue homogenates provides unique insights into cell-to-cell heterogeneity and aids in distinguishing normal cells from pathological ones. The high sensitivity and low sample consumption of capillary and on-chip electrophoresis, when integrated with fluorescence, electrochemical, and mass spectrometric detection methods, offer an ideal toolset for examining single cells and even subcellular organelles; however, the isolation and loading of such small samples into these devices is challenging. Recent advances have addressed this issue by interfacing a variety of enhanced mechanical, microfluidic, and optical sampling techniques to capillary and on-chip electrophoresis instruments for single-cell analyses.

Microfluidic carbon-blackened polydimethylsiloxane device with reduced ultra violet background fluorescence for simultaneous two-color ultra violet/visible-laser induced fluorescence detection in single cell analysis

In single cell analysis (SCA), individual cell-specific properties and inhomogeneous cellular responses are being investigated that is not subjected to ensemble-averaging or heterogeneous cell population effects. For proteomic single cell analysis, ultra-sensitive and reproducible separation and detection techniques are essential. Microfluidic devices combined with UV laser induced fluorescence (UV-LIF) detection have been proposed to fulfill these requirements. Here, we report on a novel microfluidic chip fabrication procedure that combines straightforward production of polydimethylsiloxane (PDMS) chips with a reduced UV fluorescence background (83%-reduction) by using PDMS droplets with carbon black pigments (CBP) as additives. The CBP-droplet is placed at the point of detection, whereas the rest of the chip remains transparent, ensuring full optical control of the chip. We systematically studied the relation of the UV background fluorescence at CBP to PDMS ratios (varying from 1:10 to 1:1000) for different UV laser powers. Using a CBP/PDMS ratio of 1:20, detection of a 100 nM tryptophan solution (S/N = 3.5) was possible, providing a theoretical limit of detection of 86 nM (with S/N = 3). Via simultaneous two color UV/VIS-LIF detection, we were able to demonstrate the electrophoretic separation of an analyte mixture of 500 nM tryptophan (UV) and 5 nM fluorescein (VIS) within 30 s. As an application, two color LIF detection was also used for the electrophoretic separation of the protein content from a GFP-labeled single Spodoptera frugiperda (Sf9) insect cell. Thereby just one single peak could be measured in the visible spectral range that could be correlated with one single peak among others in the ultraviolet spectra. This indicates an identification of the labeled protein γ-PKC and envisions a further feasible identification of more than one single protein in the future.

Capillary separations in metabolomics

Capillary-based separations offer increased resolution, low mass LOD and, in the case of MS, higher sensitivity. The chemical diversity and wide dynamic range of the metabolome requires systems that offer breadth and depth of analysis. In this review, we will highlight novel chemical innovations, technological advancements and various applications of capillary separations in the field of metabolomics.

Bioanalytical applications of capillary electrophoresis with laser-induced native fluorescence detection

In this article we describe recent developments and applications of capillary electrophoresis (CE) coupled with laser-induced native fluorescence (LINF) detection in the analysis of biological, pharmaceutical and environmental samples. Compared with traditional UV absorbance detection used in CE, the LINF technique can greatly improve the concentration sensitivity of CE without the need for derivatization; the only requirement being that the analyte must have native fluorescence. Instrumentation and laser sources used in CE–LINF are summarized and specific applications of CE–LINF to small-biomolecule analysis, profiling of human biofluids, detection of native fluorescent peptides and proteins, single-cell analysis and the use of online sample preconcentration methods are also reviewed in detail.

Label-free fluorescence detection in capillary and microchip electrophoresis

Herein, we summarize the current status of native fluorescence detection in microchannel electrophoresis, with a strong focus on chip-based systems. Fluorescence detection is a powerful technique with unsurpassed sensitivity down to the single-molecule level. Accordingly fluorescence detection is attractive in combination with miniaturised separation techniques. A drawback is, however, the need to derivatize most analytes prior to analysis. This can often be circumvented by utilising excitation light in the UV spectral range in order to excite intrinsic fluorescence. As sensitive absorbance detection is challenging in chip-based systems, deep-UV fluorescence detection is currently one of the most general optical detection techniques in microchip electrophoresis, which is especially attractive for the detection of unlabelled proteins. This review gives an overview of research on native fluorescence detection in capillary (CE) and microchip electrophoresis (MCE) between 1998 and 2008. It discusses material aspects of native fluorescence detection and the instrumentation used, with particular focus on the detector design. Newer developments, featured techniques, and their prospects in the future are also included. In the last section, applications in bioanalysis, drug determination, and environmental analysis are reviewed with regard to limits of detection.

Serotonin modulates transmitter release at central Lymnaea synapses through a G-protein-coupled and cAMP-mediated pathway

Neuromodulation is central to all nervous system function, although the precise mechanisms by which neurotransmitters affect synaptic efficacy between central neurons remain to be fully elucidated. In this study, we examined the neuromodulatory action of serotonin [5-hydroxytryptamine (5-HT)] at central synapses between identified neurons from the pond snail Lymnaea stagnalis. Using whole-cell voltage-clamp and sharp electrode recording, we show that 5-HT strongly depresses synaptic strength between cultured, cholinergic neuron visceral dorsal 4 (VD4 - presynaptic) and its serotonergic target left pedal dorsal 1 (LPeD1 - postsynaptic). This inhibition was accompanied by a reduction in synaptic depression, but had no effect on postsynaptic input resistance, indicating a presynaptic origin. In addition, serotonin inhibited the presynaptic calcium current (I(Ca)) on a similar time course as the change in synaptic transmission. Introduction of a non-condensable GDP analog, GDP-beta-S, through the presynaptic pipette inhibited the serotonin-mediated effect on I(Ca.) Similar results were obtained with a membrane-impermeable inactive cAMP analog, 8OH-cAMP. Furthermore, stimulation of the serotonergic postsynaptic cell also inhibited presynaptic currents, indicating the presence of a negative feedback loop between LPeD1 and VD4. Taken together, this study provides direct evidence for a negative feedback mechanism, whereby the activity of a presynaptic respiratory central pattern-generating neuron is regulated by its postsynaptic target cell. We demonstrate that either serotonin or LPeD1 activity-induced depression of presynaptic transmitter release from VD4 involves voltage-gated calcium channels and is mediated through a G-protein-coupled and cAMP-mediated system.

Coupling of complex aromatic ring vibrations to solvent through hydrogen bonds: effect of varied on-ring and off-ring hydrogen-bonding substitutions

In this study, we examine the coupling of a complex ring vibration to solvent through hydrogen-bonding interactions. We compare phenylalanine, tyrosine, l-dopa, dopamine, norepinephrine, epinephrine, and hydroxyl-dl-dopa, a group of physiologically important small molecules that vary by single differences in H-bonding substitution. By examination of the temperature dependence of infrared absorptions of these molecules, we show that complex, many-atom vibrations can be coupled to solvent through hydrogen bonds and that the extent of that coupling is dependent on the degree of both on- and off-ring H-bonding substitution. The coupling is seen as a temperature-dependent frequency shift in infrared spectra, but the determination of the physical origin of that shift is based on additional data from temperature-dependent optical experiments and ab initio calculations. The optical experiments show that these small molecules are most sensitive to their immediate H-bonding environment rather than to bulk solvent properties. Ab initio calculations demonstrate H-bond-mediated vibrational coupling for the system of interest and also show that the overall small molecule solvent dependence is determined by a complex interplay of specific interactions and bulk solvation characteristics. Our findings indicate that a full understanding of biomolecule vibrational properties must include consideration of explicit hydrogen-bonding interactions with the surrounding microenvironment.

Recent developments in CE and CEC of peptides

The article brings a comprehensive survey of recent developments and applications of high-performance capillary electromigration methods, zone electrophoresis, ITP, IEF, affinity electrophoresis, EKC, and electrochromatography, to analysis, preparation, and physicochemical characterization of peptides. New approaches to the theoretical description and experimental verification of electromigration behavior of peptides and to methodology of their separations, such as sample preparation, adsorption suppression, and detection, are presented. Novel developments in individual CE and CEC modes are shown and several types of their applications to peptide analysis are presented: conventional qualitative and quantitative analysis, purity control, determination in biomatrices, monitoring of chemical and enzymatical reactions and physical changes, amino acid and sequence analysis, and peptide mapping of proteins. Some examples of micropreparative peptide separations are given and capabilities of CE and CEC techniques to provide important physicochemical characteristics of peptides are demonstrated.

Chemical analysis of single cells

Chemical analysis of single cells requires methods for quickly and quantitatively detecting a diverse array of analytes from extremely small volumes (femtoliters to nanoliters) with very high sensitivity and selectivity. Microelectrophoretic separations, using both traditional capillary electrophoresis and emerging microfluidic methods, are well suited for handling the unique size of single cells and limited numbers of intracellular molecules. Numerous analytes, ranging from small molecules such as amino acids and neurotransmitters to large proteins and subcellular organelles, have been quantified in single cells using microelectrophoretic separation techniques. Microseparation techniques, coupled to varying detection schemes including absorbance and fluorescence detection, electrochemical detection, and mass spectrometry, have allowed researchers to examine a number of processes inside single cells. This review also touches on a promising direction in single cell cytometry: the development of microfluidics for integrated cellular manipulation, chemical processing, and separation of cellular contents.

Chemical cytometry: fluorescence-based single-cell analysis

Cytometry deals with the analysis of the composition of single cells. Flow and image cytometry employ antibody-based stains to characterize a handful of components in single cells. Chemical cytometry, in contrast, employs a suite of powerful analytical tools to characterize a large number of components. Tools have been developed to characterize nucleic acids, proteins, and metabolites in single cells. Whereas nucleic acid analysis employs powerful polymerase chain reaction-based amplification techniques, protein and metabolite analysis tends to employ capillary electrophoresis separation and ultrasensitive laser-induced fluorescence detection. It is now possible to detect yoctomole amounts of many analytes in single cells.

Contributions of capillary electrophoresis to neuroscience

Capillary electrophoresis (CE) is a small-volume separation approach amenable to the analysis of complex samples for their small molecule, peptide and protein content. A number of the features of CE make it a method of choice for addressing questions related to neurochemistry. The figures of merit inherent to CE that make it well suited for studying cell-to-cell and intracellular signaling include small sample volumes, high separation efficiency, the ability for online analyte concentration, and compatibility with sensitive and high-information content detection methods. A variety of instrumental aspects are detailed, including detection methods and sampling techniques that are particularly useful for the analysis of signaling molecules. Studies that have used these techniques to increase our understanding of neurobiology are emphasized throughout. One notable application is single neuron chemical analysis, a research area that has been greatly advanced by CE.