A review on the applicability of activated carbon derived from plant biomass in adsorption of chromium, copper, and zinc from industrial wastewater

Clean-up of wastewater discharged from zinc industry through application of zeolite 4A produced from a waste contaminated by lubricant oil components

The zeolite 4 A powders were sustainably derived from clay-based waste contaminated with the spent lubricant oil. Then, the products were used to treat the wastewater discharged from a local zinc industry. The main challenge is removal of toxic organic components from the waste and conversion of obtained precursor to the zeolite structure, simultaneously. The variation in crystallinity was studied as a function of composition, fusion temperature, aging, and recrystallization times. The zinc adsorption was found to be markedly dependent not only on sodium carbonate/waste ratio but also on aluminum hydroxide content. However, pronounced adsorption was observed over the particles fabricated through the fusion at 900 °C. The relative crystallinity, ∼32 %, is crucial for the effective immobilization of heavy metal ions like Cd2+, Ni2+, and Zn2+ from the wastewater. This level of crystallinity is achievable with the control of aging and recrystallization times, both in 3 h. The maximal zinc adsorption capacity, ∼143 mg g-1, was obtained for the particles with large pores, 48 nm, facilitating the ion diffusion into the adsorbent. On the other hand, the appropriate electrical charge surface expressed based on zeta potential, -43 mV, provided a proper condition for the electrostatic adsorption.

Eco-Friendly Hydrogel Beads from Seashell Waste for Efficient Removal of Heavy Metals from Water

The objective of this study is to develop a calcium carbonate-based adsorbent derived from Cellana Tramoscrica seashells, incorporated into a sodium alginate matrix (Na-Alg@CTs) to form hydrogel beads, for the efficient removal of Cu (II) and Zn (II) heavy metals from aqueous solutions. XRD, SEM/EDS, and FTIR analysis confirm the successful synthesis and characterization of the fabricated adsorbent. The adsorption study of Cu (II) and Zn (II) onto Na-Alg@CTs hydrogel beads revealed that the Langmuir model was the most suitable for characterizing the adsorption isotherms, suggesting monolayer coverage. Na-Alg@CTs exhibited a maximum Langmuir adsorption capacity of 368.58 mg/g and 1075.67 mg/g for Cu (II) and Zn (II), respectively. Additionally, the kinetics followed the pseudo-second-order model, indicating that the adsorption process is primarily governed by chemisorption. The thermodynamic study suggests that the uptake of metal ions on Na-Alg@CTs hydrogel beads is spontaneous and endothermic. The exceptional adsorption capacity, eco-friendly nature, and low-cost characteristics of Na-Alg@CTs hydrogel beads make them an ideal adsorbent for the removal of Cu (II) and Zn (II) from wastewater.

Landfill leachate: An invisible threat to soil quality of temperate Himalayas

Landfills are the most affordable and popular method for managing waste in many parts of the world, However, in most developing nations, including India, the infiltration of hazardous materials from improperly managed dumping site continues to be a significant environmental problem. Around the world, leachate is a significant point source of contamination in numerous environmental media, including soil, groundwater, and surface water. Soil is an important asset as it is the key factor for food production and has tremendous significance in achieving sustainable development goals (SDGs). The contaminants from soil enter into food chain and ultimately reach humans. So in order to prevent the adverse effects of toxic elements on humans, there is need to maintain the soil quality and to prevent deterioration. Keeping in view the consequences of unscientific management of waste, the goal of the experiment was to determine how landfill leachate from Achan landfill affected the soil quality in the temperate Himalayas. All four seasons of the year, viz Spring, Summer, Autumn, and Winter, at four sites viz, Center of dumping site, inside, Outside and Control were monitored. Among sites center was found to have maximum value of EC (3.04 dS/m), Moisture content (42.51%), N (285.43 mg/kg), P (70.07 mg/kg), K (265.71 mg/kg), Ca (957.67 mg/kg), Mg(402.42 mg/kg), Zn (2.02 mg/kg), Fe (10.56 mg/kg), Cu (2.07 mg/kg), Mn (10.73 mg/kg), Pb (85.02 mg/kg), Cd (4.50 mg/kg), Ni (29.04 mg/kg), Cr (23.37 mg/kg), As (14.10 mg/kg). While as the lowest value of all parameters was reported at control site. From the study it is recommended that the waste generated is mostly organic (65-75%), thus can be segregated and treated at source. The waste can be treated at source using microbial consortium technology in order to transform the waste in to wealth in a sustainable way and to prevent the deterioration of soil quality.

Multifaceted roles of zinc nanoparticles in alleviating heavy metal toxicity in plants: a comprehensive review and future perspectives

Heavy metal (HM) toxicity is a serious concern across the globe owing to their harmful impacts on plants, animals, and humans. Zinc oxide nanoparticles (ZnO-NPs) have gained appreciable attention in mitigating the adverse effects of abiotic stresses. The exogenous application of ZnO-NPs induces tolerance against HMs by improving plant physiological, metabolic, and molecular responses. They also interact with potential osmolytes and phyto-hormones to regulate the plant performance under HM stress. Moreover, ZnO-NPs also work synergistically with microbes and gene expression which helps to withstand HM toxicity. Additionally, ZnO-NPs also restrict the uptake and accumulation of HMs in plants which improves the plant performance. This review highlights the promising role of ZnO-NPs in mitigating the adverse impacts of HMs in plants. In this review, we explained the different mechanisms mediated by ZnO-NPs to counter the toxic effects of HMs. We also discussed the interactions of ZnO-NPs with osmolytes, phytohormones, and microbes in mitigating the toxic effects of HMs in plants. This review will help to learn more about the role of ZnO-NPs to mitigate HM toxicity in plants. Therefore, it will provide new insights to ensure sustainable and safer production with ZnO-NPs in HM-polluted soils.

Pyrolysis and Physicochemical, Thermokinetic and Thermodynamic Analyses of Ceiba aesculifolia (Kunth) Britt and Baker Waste to Evaluate Its Bioenergy Potential

Ceiba aesculifolia is an important species in Mexico that generates significant amounts of biomass waste during its exploitation, which can be utilized to produce energy. This study presents the characterization of this waste based on chemical (proximal and elemental) and thermal analyses (TGA-DTG) at different heating rates (β = 10-30 °C/min (283-303 K/min)) in the presence of nitrogen and in a temperature range of 25-900 °C. Kinetic parameters were calculated and analyzed as well. Activation energy (Ea) and the pre-exponential factor (A) were determined using the Friedman (132.03 kJ/mol, 8.11E + 10 s -1), FWO (121.65 kJ/mol, 4.30E + 09), KAS (118.14 kJ/mol, 2.41E + 09), and Kissinger (155.85 kJ/mol, 3.47E + 11) kinetic methods. Variation in the reaction order, n (0.3937-0.6141), was obtained by Avrami's theory. We also calculated the thermodynamic parameters (ΔH, ΔG, ΔS) for each kinetic method applied. The results for Ea, A, n, ΔH, ΔG, and ΔS show that this biomass waste is apt for use in pyrolysis. Moreover, the moisture (<10%), ash (<2%), volatile material (>80%), and HHV (>19%) contents of C. aesculifolia allowed us to predict acceptable performance in generating energy and fuels. Finally, infrared spectroscopy analysis (FT-IR) allowed us to identify important functional groups, including one that belongs to the family of the aliphatic hydrocarbons.

Efficient removal of cationic dyes using lemon peel-chitosan hydrogel composite: RSM-CCD optimization and adsorption studies

The most prominent and easily identifiable factor of water purity is its colour, which may be both physically undesirable, and act as an alert towards potential environmental contamination. The current study describes the optimum synthesis technique for Lemon Peel-Chitosan hydrogel using the Response Surface Methodology integrated Central composite Design (RSM-CCD). This adsorbent is both environmentally friendly and cost-effective. The hydrogel exhibited a maximal dye removal capacity of 24.984, 24.788, 24.862, 23.483, 24.409, and 24.726 mg g-1, for 10 mg L-1 aqueous medium of Safranin O, Methylene blue, Basic fuchsin, Toluidine blue, Brilliant green and Crystal violet, respectively. The adsorption kinetics and isotherm data suggest that the Pseudo second-order kinetic and Freundlich adsorption isotherm models precisely represent the respective behaviour of all the dyes. The thermodynamic viability of the process is determined by the values of ΔG, ΔH, and ΔS. The probable mechanism of adsorption was the electrostatic interaction between the dye molecules and the hydrogel. The regenerated hydrogel had removal efficiencies of over 80 % even after enduring six cycles. Hence, the exceptional recyclability and utility of the adsorbent show their sustainability for wastewater treatment in textile factories.

Enhanced capacity of thiol-functionalized sugarcane bagasse and rice husk biochars for arsenite sorption in aqueous solutions

The utilization of biowastes for producing biochar to remove potentially toxic elements from water represents an important pathway for aquatic ecosystem decontamination. Here we explored the significance of thiol-functionalization on sugarcane bagasse biochar (Th/SCB-BC) and rice husk biochar (Th/RH-BC) to enhance arsenite (As(III)) removal capacity from water and compared their efficiency with both pristine biochars (SCB-BC and RH-BC). The maximum As(III) sorption was found on Th/SCB-BC and Th/RH-BC (2.88 and 2.51 mg g-1, respectively) compared to the SCB-BC and RH-BC (1.51 and 1.40 mg g-1). Relatively, a greater percentage of As(III) removal was obtained with Th/SCB-BC and Th/RH-BC (92% and 83%, respectively) at a pH 7 compared to pristine SCB-BC and RH-BC (65% and 55%) at 6 mg L-1 initial As(III) concentration, 2 h contact time and 1 g L-1 sorbent dose. Langmuir (R2 = 0.99) isotherm and pseudo-second-order kinetic (R2 = 0.99) models provided the best fits to As(III) sorption data. Desorption experiments indicated that the regeneration ability of biochars decreased and it was in the order of Th/SCB-BC (88%) > Th/RH-BC (82%) > SCB-BC (77%) > RH-BC (69%) up to three sorption-desorption cycles. Fourier-transform infrared spectroscopy and X-ray photoelectron spectroscopy results demonstrated that the thiol (-S-H) functional groups were successfully grafted on the surface of two biochars and as such contributed to enhance As(III) removal from water. Spectroscopic data indicated that the surface functional moieties, such as -S-H, - OH, - COOH, and C = O were involved to increase As(III) sorption on thiol-functionalized biochars. This study highlights that thiol-grafting on both biochars, notably on SCB-BC, enhanced their ability to remove As(III) from water, which can be used as an effective technique for the treatment of As from drinking water.

Mechanistic approach of tannery wastewater and sulfadiazine mutual toxicity in wheat (Triticum aestivum L.) and mitigation through exogenous application of gallic acid

Excessive release of chromium (Cr) from the tanning industry and antibiotics from livestock caused severe hazards to humans. Gallic acid (GA 10 mM) alleviated alone/combined SDZ 30 mg kg-1 and TWW 40, 60, and 100% stress in wheat. GA (10 mM) decreased the TSP 12 and 13%, TFAA 8 and 10%, TSS 14 and 16%, RS 18 and 16%, and NRS 11 and 9% in shoots and grains under SDZ + TWW (30 mg kg-1+100%), compared without foliar. GA (10 mM) declined the MDA 20 and 31, EL 13 and 36%, H2O2 17 and 15%, O2•- 10 and 11% in leaves and roots, under combined SDZ + TWW (30 mg kg-1+100%), compared without foliar. GA (10 mM) improved the POD 106 and 30%, SOD 145 and 31%, CAT 78, and 35%, APX 100 and 25% in leaves and roots under combined SDZ + TWW (30 mg kg-1+100%), compared without foliar application. Considerably GA (10 mM) reduced total Cr 18, CrIII 20, and CrVI 50% in roots and shoots 19, 41, and 48%, and grains 15, 27, and 29% respectively, under combined SDZ + TWW (30 mg kg-1+100%) stress, compared without foliar. Overall, GA boosted the wheat growth, physiology, and defence system by inhibiting the combined SDZ + Cr toxicity.

Unraveling the contribution of copper seed priming in enhancing chromium tolerance in wheat by improving germination, growth, and grain yield

Exposure to chromium (Cr) on farmlands drastically restricts the growth and productivity of cereal crops, including wheat (Triticum aestivum L.). Utilizing micronutrients, the seed-priming strategy is crucial to preventing the adverse consequences of Cr-stress. Nevertheless, additional investigation needs to be conducted to figure out whether Cu-priming remedies are beneficial for wheat experiencing Cr-stress. The objective of this study was to ascertain the contribution of Cu-treated seed priming in the mitigation of detrimental impacts of Cr-stress on wheat germination, growth, and production. Two wheat cultivars, Dilkash-20 and Subhani-21, were subjected to seed priming treatments (0 mg/L, 0.1 mg/L, and 1.0 mg/L) of Cu under Cr-stress levels (200 mg/kg) in two successive experiments, respectively, petri-dish and soil-filled pot experiments. The Cu-priming significantly enhanced the wheat seed germination, plant growth, and grain yield under Cr-stress. Cu priming improved enzyme activities such as glutathione peroxidase (14.60, 16.30%), superoxide dismutase (62.55, 115.21%), peroxidase, catalase (78.39, 80.23%), ascorbate peroxidase(17.72, 20.32%), and key primary and secondary metabolites such as proline (54.19, 81.27%), glycine betaine (40.13, 79.39%), total soluble proteins (47.92, 51.58%), phenolics (40.05, 18.61%), and flavonoids (56.90, 113.46%), respectively, of Dilkash-20 and Subhani-21 under Cr-stress. The outcome of our investigation underscored the efficacy of Cu-priming treatments (0.1 mg/L and 1.0 mg/L) in Cr-stress circumstances to augment wheat germination, growth, and grain yield.

Removal of doxorubicin hydrochloride and crystal violet from aqueous solutions using spray-dried niobium oxide coated with chitosan-activated carbon: Experimental and DFT calculations

Spray-dried niobium oxide coated with chitosan-activated carbon (NIC) was synthesized and used to remove doxorubicin hydrochloride and crystal violet from aqueous solutions under different parameters such as solution pH (2, 4, 6, and 8), contact time (1 to 9 h), initial concentration (20 to 200 mg L-1), and competing ions (0.1 M of CaCl2 and NaCl). The addition of 5 % chitosan-activated carbon to the matrix of niobium oxide slightly increased the specific surface area from 26 to 30 m2 g-1, with the introduction of a carboxylic functional group. This led to an increase in the amount of adsorbed doxorubicin hydrochloride (DOH) from 30 to 44 mg g-1 and that of crystal violet (CV) from 15 to 32 mg g-1 from the initial respective 100 mg L-1 at pH 8. The data from the concentration study fitted into Liu isotherm having adsorption capacity of 128 and 57 mg g-1 for DOH and CV respectively, while pseudo first and second order are more suitable for adsorption kinetics. The additional functional groups on the IR spectrum of NIC after the adsorption of DOH and CV confirmed the interaction between NIC and the adsorbates' molecules. The mechanism of adsorption was supported by DFT calculations.

Interaction of titanium dioxide nanoparticles with PVC-microplastics and chromium counteracts oxidative injuries in Trachyspermum ammi L. by modulating antioxidants and gene expression

The emergence of polyvinyl chloride (PVC) microplastics (MPs) as pollutants in agricultural soils is increasingly alarming, presenting significant toxic threats to soil ecosystems. Ajwain (Trachyspermum ammi L.), a plant of significant medicinal and culinary value, is increasingly subjected to environmental stressors that threaten its growth and productivity. This situation is particularly acute given the well-documented toxicity of chromium (Cr), which has been shown to adversely affect plant biomass and escalate risks to the productivity of such economically and therapeutically important species. The present study was conducted to investigate the individual effects of different levels of PVC-MPs (0, 2, and 4 mg L-1) and Cr (0, 150, and 300 mg kg-1) on various aspects of plant growth. Specifically, we examined growth and biomass, photosynthetic pigments, gas exchange attributes, oxidative stress responses, antioxidant compound activity (both enzymatic and nonenzymatic), gene expression, sugar content, nutritional status, organic acid exudation, and Cr accumulation in different parts of Ajwain (Trachyspermum ammi L.) seedlings, which were also exposed to varying levels of titanium dioxide (TiO2) nanoparticles (NPs) (0, 25, and 50 µg mL-1). Results from the present study showed that the increasing levels of Cr and PVC-MPs in soils significantly decreased plant growth and biomass, photosynthetic pigments, gas exchange attributes, sugars, and nutritional contents from the roots and shoots of the plants. Conversely, increasing levels of Cr and PVC-MPs in the soil increased oxidative stress indicators in term of malondialdehyde, hydrogen peroxide, and electrolyte leakage, and also increased organic acid exudation pattern in the roots of T. ammi seedlings. Interestingly, the application of TiO2-NPs counteracted the toxicity of Cr and PVC-MPs in T. ammi seedlings, leading to greater growth and biomass. This protective effect is facilitated by the NPs' ability to sequester reactive oxygen species, thereby reducing oxidative stress and lowering Cr concentrations in both the roots and shoots of the plants. Our research findings indicated that the application of TiO2-NPs has been shown to enhance the resilience of T. ammi seedlings to Cr and PVC-MPs toxicity, leading to not only improved biomass but also a healthier physiological state of the plants. This was demonstrated by a more balanced exudation of organic acids, which is a critical response mechanism to metal stress.

Proteomic insights to decipher nanoparticle uptake, translocation, and intercellular mechanisms in plants

Advent of proteomic techniques has made it possible to identify a broad spectrum of proteins in living systems. Studying the impact of nanoparticle (NP)-mediated plant protein responses is an emerging field. NPs are continuously being released into the environment and directly or indirectly affect plant's biochemistry. Exposure of plants to NPs, especially crops, poses a significant risk to the food chain, leading to changes in underlying metabolic processes. Once absorbed by plants, NPs interact with cellular proteins, thereby inducing changes in plant protein patterns. Based on the reactivity, properties, and translocation of nanoparticles, NPs can interfere with proteins involved in various cellular processes in plants such as energy regulation, redox metabolism, and cytotoxicity. Such interactions of NPs at the subcellular level enhance ROS scavenging activity, especially under stress conditions. Although higher concentrations of NPs induce ROS production and hinder oxidative mechanisms under stress conditions, NPs also mediate metabolic changes from fermentation to normal cellular processes. Although there has been lots of work conducted to understand the different effects of NPs on plants, the knowledge of proteomic responses of plants toward NPs is still very limited. This review has focused on the multi-omic analysis of NP interaction mechanisms with crop plants mainly centering on the proteomic perspective in response to both stress and non-stressed conditions. Furthermore, NP-specific interaction mechanisms with the biological pathways are discussed in detail.

Emerging trends in wastewater treatment: Addressing microorganic pollutants and environmental impacts

This review focuses on the challenges and advances associated with the treatment and management of microorganic pollutants, encompassing pesticides, industrial chemicals, and persistent organic pollutants (POPs) in the environment. The translocation of these contaminants across multiple media, particularly through atmospheric transport, emphasizes their pervasive nature and the subsequent ecological risks. The urgency to develop cost-effective remediation strategies for emerging organic contaminants is paramount. As such, wastewater-based epidemiology and the increasing concern over estrogenicity are explored. By incorporating conventional and innovative wastewater treatment techniques, this article highlights the integration of environmental management strategies, analytical methodologies, and the importance of renewable energy in waste treatment. The primary objective is to provide a comprehensive perspective on the current scenario, imminent threats, and future directions in mitigating the effects of these pollutants on the environment. Furthermore, the review underscores the need for international collaboration in developing standardized guidelines and policies for monitoring and controlling these microorganic pollutants. It advocates for increased investment in research and development of advanced materials and technologies that can efficiently remove or neutralize these contaminants, thereby safeguarding environmental health and promoting sustainable practice.

Advancing the development of nanocomposite adsorbent through zinc-doped nickel ferrite-pinecone biochar for removal of chromium (VI) from wastewater

Leather and textile industrial effluents are the main disseminating routes for chromium contamination of water bodies, causing adverse impacts on public and environmental health. The attempt to remediate chromium through conventional wastewater treatment methods is inefficient. Therefore, this study aims to synthesize zinc-doped nickel ferrite pinecone biochar (Zn-NiF@PBC) nanocomposite for the removal of chromium from wastewater systems. The Zn-NiF@PBC nanocomposite was synthesized via the co-precipitation method. The properties of zinc-doped nickel ferrite (Zn-NiF) were effectively modified by blending with biochar at 1, 5, 10, and 15 % (w/w) which was successfully embedded with Zn-Ni ferrite nanoparticles. This was characterized and confirmed by typical adsorbent properties such as a high surface area of 104 m2/g, conducive pore volume of 0.117 cm3/g and pore size of 3.41 nm (BET), interactive multi-functional groups (FTIR), surface charge determination (pHpzc,), crystalline structure (XRD) and very rough surface morphology (SEM). The maximum chromium adsorption was found to be 95 % at the specific experimental condition of pH 3, adsorbent dose 1 g/50 mL, contact time 120 min, and initial chromium concentration 100 mg/L. The adsorption experimental data was best fitted with the Langmuir isotherm at R2 0.98 indicating the adsorption process was homogeneous and monolayer whereas the kinetics adsorption was resembling the second-order kinetic at R2 0.99. Moreover, the adsorption thermodynamics was spontaneous, endothermic, and increased the change in entropy. Finally, the regeneration of Zn-NiF@PBC was found to be effective up to five 5 cycles but gradually degrading in terms of removal efficiency after 3 cycles. In general, Zn-NiF@PBC can remediate chromium from wastewater with huge potential for scale-up and extend to other pollutants clear-up.

Physio-anatomical modifications and element allocation pattern in Alternanthera tenella Colla. associated with phytoextraction of chromium

Intensive industrial activities have elevated chromium (Cr) concentrations in the environment, particularly in soil and water, posing a significant threat due to its cytotoxic and carcinogenic properties. Phytoremediation has emerged as a sustainable and economical alternative for detoxifying pollutants. In this context, an attempt has been made to assess the efficacy of Cr remediation by the invasive plant Alternanthera tenella Colla. The study investigated morphological, anatomical, and physiological adaptations in plant tissues in response to 240 µM of K2Cr2O7, considering elemental distribution patterns and bioaccumulation potential. Growth parameter assessments revealed a notable 50% reduction in root elongation and biomass content; however, the plant exhibited a comparatively higher tolerance index (47%) under Cr stress. Chromium significantly influenced macro and micro-elemental distribution in plant tissues, particularly in roots and leaves. Structural modifications, including changes in the thickness and diameter of xylem walls in the root, stem, and leaf tissues of Cr-treated A. tenella, were observed. Distinct cell structural distortions and Cr deposit inclusions in the xylem wall and inner parenchyma cells were distinct. Under Cr stress, there was a reduction in pigment content and metabolites such as proteins and soluble sugars, while proline, phenol, and malondialdehyde showed a twofold increase. The concentration of Cr was higher in the shoots of A. tenella (185.7 mg/kg DW) than in the roots (179.625 mg/kg DW). With a high BCFroot value (16.23) and TF > 1, coupled with effective mechanisms to cope with metal stress, A. tenella emerges as an ideal candidate for chromium phytoextraction.

Waste biomass derived highly-porous carbon material for toxic metal removal: Optimisation, mechanisms and environmental implications

Toxic elements, lead, and copper are often found in wastewater discharged from industries such as mining. The discharge of untreated effluent poses severe environmental challenges and sorption methods using agricultural waste materials are proposed as an efficient and cost-effective solution. For this research, activated sunflower material (ASM) was prepared from abundantly available agricultural sunflower waste residues and utilised to remove Pb2+ and Cu2+ ions from an aqueous medium. To begin, we examine variables that may have an impact on the adsorption process, such as pH, contact time, adsorbent dose, and initial concentration using Box-Behnken Design (BBD) to find optimal conditions. Maximum removal efficiency was found at a pH of 5, contact time of 180 min, and initial concentration of 50 mg/L for Pb2+ and 150 mg/L for Cu2+. Additionally, adsorbent dose differed by element, for Cu2+ it was 200 mg, whilst for Pb2+ it was 124 mg. Features of activated carbon such as morphology, elemental composition, textural properties, and surface functionalities were characterised using SEM-EDS, BET, FTIR, and XPS. The adsorption equilibrium data were analysed by Langmuir, Freundlich, and Dubinin-Radushkevich isotherm models. It was found that the obtained results for Pb2+ adsorption were better described with the Freundlich isotherm model. Maximum adsorption capacities for Pb2+ and Cu2+ were 91.8 mg/g and 20.5 mg/g, respectively. Furthermore, kinetic studies confirmed that the adsorption process followed a pseudo-first-order kinetic model for Pb2+, but for Cu2+ all applied kinetic models fitted experimental data with the same values of the correlation coefficient (R2 = 0.99). After comprehensive analysis using the methods mentioned above, ASM was tested for the removal of Cu2+ from mining wastewater sample, and the obtained removal efficiency was 98.6% ± 2.0%. The results of desorption experiments conducted, confirm that ASM has good potential to be reused for the purpose of removing Cu2+ from wastewater.

Effect of drought and soil heavy metal contamination on three maple species: a case study of Kastamonu University campus in Türkiye

This study investigated the effects of heavy metals and drought on tree drying in three maple species located in the Kastamonu Campus in northwestern Türkiye. Soil samples were taken from 0-30 cm depth under maple species, and some soil properties were analyzed. The standardized precipitation evapotranspiration index was calculated for the drought impression using 71 years of climate data. The severe drought has had its effect (1.516) since August 2020. There was an extreme drought in January and February 2021 (-2.032 and -2.076, respectively), and this drought effect lasted until August as a severe drought. Chromium concentration at maple species was almost twice higher than the Maximum Allowable Limit for Türkiye (> 100 mg kg-1). The highest nickel concentration was found under Acer pseudoplatanus (97.25 mg kg-1) and Acer negundo (108.13 mg kg-1). The sampling sites were nonsignificant for copper (p = 0.806), lead (p = 0.916), and zinc (p = 0.866) heavy metals. Phyllosticta minima and Phyllactinia marissallii were detected in maple trees. In conclusion, it is understood that drought and heavy metal accumulation (chromium, nickel) in the soil affect tree drying. Physiological drought was first seen in trees due to the lack of rainfall in 2020. Soils were contaminated with heavy metals, and finally, diseases were seen. These results show that adverse climate events due to global climate change will have a negative impact on the growth and development of maple species, as their severity is expected to increase in the next few years.

Enhancing chromium removal and recovery from industrial wastewater using sustainable and efficient nanomaterial: A review

Water contamination can be detrimental to the human health due to higher concentration of carcinogenic heavy metals such as chromium (Cr) in the wastewater. Many traditional methods are being employed in wastewater treatment plants for Cr removal to control the environmental impacts. Such methods include ion exchange, coagulation, membrane filtration, and chemical precipitation and microbial degradation. Recent advances in materials science and green chemistry have led to the development of nanomaterial that possess high specific surface areas and multiple functions, making them suitable for removing metals such as Cr from wastewater. Literature shows that the most efficient, effective, clean, and long-lasting approach for removing heavy metals from wastewater involves adsorbing heavy metals onto the surface of nanomaterial. This review assesses the removal methods of Cr from wastewater, advantages and disadvantages of using nanomaterial to remove Cr from wastewater and potential negative impacts on human health. The latest trends and developments in Cr removal strategies using nanomaterial adsorption are also explored in the present review.

Comparative physiological and metabolomics analyses using Ag⎯NPs and HAS31 (PGPR) to alleviate Cr stress in barley (Hordeum vulgare L.)

In the current industrial scenario, chromium (Cr) as a metal is of great importance but poses a major threat to the ecosystem because of its toxicity, but fewer studies have been conducted on its effects and alleviation strategies by using nanoparticles (NPs) and plant growth promoting rhizobacteria (PGPR). Taking into consideration the positive effects of silver⎯nanoparticles (Ag⎯NPs) and (HAS31) rhizobacteria in reducing Cr toxicity in plants, the present study was conducted. A pot experiment was conducted to determine the effects of single and/or combined application of different levels [0 (no Ag⎯NPS), 15 and 30 mM] of Ag⎯NPs and HAS31 [0 (no HAS31), 50 g and 100 g] on Cr accumulation, morpho-physiological and antioxidative defense attributes of barley (Hordeum vulgare L.) exposed to severe Cr stress [0 (without Cr stress), 50 and 100 μM)]. Results from the present study showed that the increasing levels of Cr in the soil significantly (P < 0.05) decreased plant growth and biomass, photosynthetic pigments, gas exchange attributes, sugars, and nutritional contents from the roots and shoots of the plants. In contrast, increasing levels of Cr in the soil significantly (P < 0.05) increased oxidative stress indicators in term of malondialdehyde, hydrogen peroxide, and electrolyte leakage, and also increased organic acid exudation patter in the roots of H. vulgare. Although, the activities of enzymatic antioxidants and the response of their gene expressions in the roots and shoots of the plants and non-enzymatic such as phenolic, flavonoid, ascorbic acid, and anthocyanin contents were increased by increasing the Cr concentration in the soil. The negative impacts of Cr injury were reduced by the application of PGPR (HAS31) and Ag⎯NPs, which increased plant growth and biomass, improved photosynthetic apparatus, antioxidant enzymes, and mineral uptake, as well as diminished the exudation of organic acids and oxidative stress indicators in roots of H. vulgare by decreasing Cr toxicity. Research findings, therefore, suggest that the application of PGPR (HAS31) and Ag⎯NPs can ameliorate Cr toxicity in H. vulgare, resulting in improved plant growth and composition under metal stress, as depicted by balanced exudation of organic acids.

Evaluation and Assessment of Trivalent and Hexavalent Chromium on Avena sativa and Soil Enzymes

Chromium (Cr) can exist in several oxidation states, but the two most stable forms-Cr(III) and Cr(VI)-have completely different biochemical characteristics. The aim of the present study was to evaluate how soil contamination with Cr(III) and Cr(VI) in the presence of Na2EDTA affects Avena sativa L. biomass; assess the remediation capacity of Avena sativa L. based on its tolerance index, translocation factor, and chromium accumulation; and investigate how these chromium species affect the soil enzyme activity and physicochemical properties of soil. This study consisted of a pot experiment divided into two groups: non-amended and amended with Na2EDTA. The Cr(III)- and Cr(VI)-contaminated soil samples were prepared in doses of 0, 5, 10, 20, and 40 mg Cr kg-1 d.m. soil. The negative effect of chromium manifested as a decreased biomass of Avena sativa L. (aboveground parts and roots). Cr(VI) proved to be more toxic than Cr(III). The tolerance indices (TI) showed that Avena sativa L. tolerates Cr(III) contamination better than Cr(VI) contamination. The translocation values for Cr(III) were much lower than for Cr(VI). Avena sativa L. proved to be of little use for the phytoextraction of chromium from soil. Dehydrogenases were the enzymes which were the most sensitive to soil contamination with Cr(III) and Cr(VI). Conversely, the catalase level was observed to be the least sensitive. Na2EDTA exacerbated the negative effects of Cr(III) and Cr(VI) on the growth and development of Avena sativa L. and soil enzyme activity.

Rhodamine B dye degradation using used face masks-derived carbon coupled with peroxymonosulfate

Catalytic carbon materials from used face masks (UFM) activated by peroxymonosulfate (PMS) were developed for the degradation of rhodamine B (RhB) dye in aqueous solution. The UFM-derived carbon (UFMC) catalyst had a relatively large surface area as well as active functional groups and promoted the generation of singlet ¹O₂ and radicals from PMS, giving a high RhB degradation performance (98.1% after 3 h) in the presence of 3 mM PMS. The UFMC could degrade only 13.7% at a minimal RhB dose of 10^-5 M. The principal reactive oxygen species of sulphate (SO₄^•), hydroxyl radicals (^•OH), and singlet ¹O₂ were discovered using electron paramagnetic resonance and radical scavenger studies. Finally, a toxicological plant and bacterial study was performed to demonstrate the potential non-toxicity of the degraded RhB water sample.

Chromium Toxicity in Plants: Signaling, Mitigation, and Future Perspectives

Plants are very often confronted by different heavy metal (HM) stressors that adversely impair their growth and productivity. Among HMs, chromium (Cr) is one of the most prevalent toxic trace metals found in agricultural soils because of anthropogenic activities, lack of efficient treatment, and unregulated disposal. It has a huge detrimental impact on the physiological, biochemical, and molecular traits of crops, in addition to being carcinogenic to humans. In soil, Cr exists in different forms, including Cr (III) "trivalent" and Cr (VI) "hexavalent", but the most pervasive and severely hazardous form to the biota is Cr (VI). Despite extensive research on the effects of Cr stress, the exact molecular mechanisms of Cr sensing, uptake, translocation, phytotoxicity, transcript processing, translation, post-translational protein modifications, as well as plant defensive responses are still largely unknown. Even though plants lack a Cr transporter system, it is efficiently accumulated and transported by other essential ion transporters, hence posing a serious challenge to the development of Cr-tolerant cultivars. In this review, we discuss Cr toxicity in plants, signaling perception, and transduction. Further, we highlight various mitigation processes for Cr toxicity in plants, such as microbial, chemical, and nano-based priming. We also discuss the biotechnological advancements in mitigating Cr toxicity in plants using plant and microbiome engineering approaches. Additionally, we also highlight the role of molecular breeding in mitigating Cr toxicity in sustainable agriculture. Finally, some conclusions are drawn along with potential directions for future research in order to better comprehend Cr signaling pathways and its mitigation in sustainable agriculture.

Hexavalent chromium-reducing plant growth-promoting rhizobacteria are utilized to bio-fortify trivalent chromium in fenugreek by promoting plant development and decreasing the toxicity of hexavalent chromium in the soil

BACKGROUND

Fenugreek is known to have good anti-diabetes properties. Moreover, several studies accounted that the trivalent form of chromium [Cr(III)] also have anti-diabetic properties. However, its hexavalent form i.e., Cr(VI) is known to be highly toxic and carcinogenic to living beings and retarded plant growth even if it is present in low concentration in soil. Many plant growth-promoting rhizobacteria (PGPR) are reported to have the potential to reduce the Cr(VI) into Cr(III) in soil. In view of the above, the present objective was designed to effectively utilize Cr(VI) reducing PGPRs for the growth and development of fenugreek plant in Cr(VI) amended soil, apart from reducing Cr(VI) in soil and fortification of Cr(III) in the aerial part of plants.

METHODS

The experiment was carried out to evaluate the effect of Cr(VI)-reducing PGPRs viz. Bacillus cereus (SUCR44); Microbacterium sp. (SUCR140); Bacillus thuringiensis (SUCR186) and B. subtilis (SUCR188) on growth, uptake and translocation of Cr as well as other physiological parameters in fenugreek grown under artificially Cr(VI) amended soil (100 mg kg^-1 of Cr(VI) in soil).

RESULTS

The aforementioned concentration of Cr(VI) in soil cause severe reduction in root length (41 %), plant height (43 %), dry root (38 %) and herb biomass (48 %), when compared with control negative (CN; uninoculated plant not grown in Cr(VI) contaminated soil). However, the presence of Microbacterium sp.-SURC140 (MB) mitigates the Cr toxicity resulting in improved root length (92 %), plant height (86 %), dry root (74 %) and herb biomass (99 %) as compared with control positive (CP; uninoculated plants grown in Cr(VI) contaminated soil). The maximum reduction in bioavailability (82 %) of Cr(VI) in soil and its uptake (50 %) by the plant were also observed in MB-treated plants. However, All Cr(VI)-reducing PGPRs failed to decrease the translocation of Cr to the aerial parts. Moreover, the plant treated with MB observed diminution in relative water content (13 %), electrolyte leakage (16%) and lipid peroxidation (38 %) as well as higher chlorophyll (37 %) carotenoids (17 %) contents and antioxidants (18%) potential.

CONCLUSION

This study demonstrates that MB can lower the Cr(VI) toxicity to the plant by reducing the bioavailable Cr(VI), consequently reducing the Cr(VI) toxicity level in soil and helping in improving the growth and yield of fenugreek. Additionally, Cr(III) uptakes and translocation may improve the effectiveness of fenugreek in treating diabetes.

Optimization of Cr (VI) removal from aqueous solution with activated carbon derived from Eichhornia crassipes under response surface methodology

Tannery industries' effluent contains a high concentration of Cr (VI) which has the potential to affect the environment and public health. Therefore, this study aimed to investigate the optimization of Cr (VI) adsorption by activated carbon (AC) derived from Eichhornia crassipes from an aqueous solution. The adsorbent was activated with dilute sulfuric acid followed by thermal activation. AC was characterized using proximate analysis, SEM, FTIR, X-ray diffraction, and the BET method. The Cr (VI) removal optimization process was performed using a central composite design under the response surface methodology. The proximate analysis showed that the moisture content, volatile matter, ash content, and fixed carbon of the activated carbon were 5.6%, 18.2%, 14.4%, and 61.8% respectively. The surface areas of the Eichhornia crassipes before activation, after activation, and after adsorption were 60.6 g/m², 794.2 g/m², and 412.6 g/m² respectively. A highly porous structure with heterogeneous and irregular shapes was observed in the SEM micrograph. In the FTIR analysis, different peaks are indicated with various functional groups. The intensity of XRD peaks decreased as 2 theta values increased, which indicates the presence of an amorphous carbon arrangement. The point of zero charge (pH_pzc) of the activated carbon was found to be 5.20. A maximum Cr (VI) removal of 98.4% was achieved at pH 5, contact time 90 min, adsorbent dose 2 g, and initial Cr (VI) concentration of 2.25 mg/L. Statistically significant interactions (P < 0.05) were observed between the initial Cr (VI) concentration and adsorbent dose as well as the initial Cr (VI) concentration and contact time. Langmuir adsorption isotherm fitted the experimental data best, with an R² value of 0.99. The separation constant (RL) indicates that the adsorption process is favorable. The kinetic experimental data were best fitted with the pseudo-second-order model with an R² value of 0.99 whereas the adsorption rate is controlled by intraparticle and extragranular diffusion processes. Generally, the AC has the potential to be a strong adsorbent candidate for wastewater treatment at the industrial level.

Overview on recent advances of magnetic metal-organic framework (MMOF) composites in removal of heavy metals from aqueous system

Developing a novel, simple, and cost-effective analytical technique with high enrichment capacity and selectivity is crucial for environmental monitoring and remediation. Metal-organic frameworks (MOFs) are porous coordination polymers that are self-assembly synthesized from organic linkers and inorganic metal ions/metal clusters. Magnetic metal-organic framework (MMOF) composites are promising candidate among the new-generation sorbent materials available for magnetic solid-phase extraction (MSPE) of environmental contaminants due to their superparamagnetism properties, high crystallinity, permanent porosity, ultrahigh specific surface area, adaptable pore shape/sizes, tunable functionality, designable framework topology, rapid and ultrahigh adsorption capacity, and reusability. In this review, we focus on recent scientific progress in the removal of heavy metal ions present in contaminated aquatic system by using MMOF composites. Different types of MMOFs, their synthetic approaches, and various properties that are harnessed for removal of heavy metal ions from contaminated water are discussed briefly. Adsorption mechanisms involved, adsorption capacity, and regeneration of the MMOF sorbents as well as recovery of heavy metal ions adsorbed that are reported in the last ten years have been discussed in this review. Moreover, particular prospects, challenges, and opportunities in future development of MMOFs towards their greener synthetic approaches for their practical industrial applications have critically been considered in this review.

Micro-/Nano-Carboxymethyl Cellulose as a Promising Biopolymer with Prospects in the Agriculture Sector: A Review

The increase in the population rate has increased the demand for safe and quality food products. However, the current agricultural system faces many challenges in producing vegetables and fruits. Indiscriminate use of pesticides and fertilizers, deficiency of water resources, short shelf life of products postharvest, and nontargeted delivery of agrochemicals are the main challenges. In this regard, carboxymethyl cellulose (CMC) is one of the most promising materials in the agriculture sector for minimizing these challenges due to its mechanical strength, viscosity, wide availability, and edibility properties. CMC also has high water absorbency; therefore, it can be used for water deficiency (as superabsorbent hydrogels). Due to the many hydroxyl groups on its surface, this substance has high efficacy in removing pollutants, such as pesticides and heavy metals. Enriching CMC coatings with additional substances, such as antimicrobial, antibrowning, antioxidant, and antisoftening materials, can provide further novel formulations with unique advantages. In addition, the encapsulation of bioactive materials or pesticides provides a targeted delivery system. This review presents a comprehensive overview of the use of CMC in agriculture and its applications for preserving fruit and vegetable quality, remediating agricultural pollution, preserving water sources, and encapsulating bioactive molecules for targeted delivery.

Effective and Low-Cost Adsorption Procedure for Removing Chemical Oxygen Demand from Wastewater Using Chemically Activated Carbon Derived from Rice Husk

Wastewater treatment by adsorption onto activated carbon is effective because it has a variety of benefits. In this work, activated carbon prepared from rice husk by chemical activation using zinc chloride was utilized to reduce chemical oxygen demand from wastewater. The as-prepared activated carbon was characterized by scanning electron microscope, Fourier transform infrared spectroscopy and nitrogen adsorption/desorption analysis. The optimum conditions for maximum removal were achieved by studying the impact of various factors such as solution pH, sorbent dose, shaking time and temperature in batch mode. The results displayed that the optimum sorption conditions were achieved at pH of 3.0, sorbent dose of 0.1 g L−1, shaking time of 100 min and at room temperature (25 °C). Based on the effect of temperature, the adsorption process is exothermic in nature. The results also implied that the isothermal data might be exceedingly elucidated by the Langmuir model. The maximum removal of chemical oxygen demand by the activated carbon was 45.9 mg g−1. The kinetic studies showed that the adsorption process follows a pseudo-first order model. The findings suggested that activated carbon from rice husk may be used as inexpensive substitutes for commercial activated carbon in the treatment of wastewater for the removal of chemical oxygen demand.

Investigating the role of different maize (Zea mays L.) cultivars by studying morpho-physiological attributes in chromium-stressed environment

Because of global land surface warming, heavy metal toxicity is expected to occur more often and more intensely, affecting the growth and development of the major cereal crops such as maize (Zea mays L.) in several ways, thus affecting the production component of food security. Hence, it is important to know the best cultivars of Z. mays in abiotic stress environment to fulfill the market demand of this staple food. For this purpose, we investigate the present study to find the best Z. mays cultivar to be grown in chromium (Cr)-contaminated sand (200 µM). In this experiment, we have studied 10 cultivars (Malka, Sadaf, Pearl, CZP, YY, YH, MMRI-yellow, Sahiwal, EV-20, and EV-77) of Z. mays grown in plastic pots for 4 weeks (in addition with seed germination) under Cr - (0 µM) and Cr + (200 µM) in sand medium. Based on the findings of the current experiment, we illustrated that Cr toxicity induced a significant (P < 0.05) reduction in shoot length, root length, shoot fresh weight, root fresh weight, shoot dry weight and root dry weight, chlorophyll a, chlorophyll b, total chlorophyll, and carotenoid content and induced oxidative damage to membrane-bounded organelles by increasing the malondialdehyde and hydrogen peroxide which were manifested by flavonoid and phenolic contents. Moreover, Cr uptake was also higher in the plants grown in the Cr-contaminated sand compared to the plants grown without the Cr-contaminated sand. We also noticed that Pearl, CZP, and Sahiwal cultivars are suggested to be Cr-tolerant cultivars as showed better growth and development in Cr-contaminated sand while Sadaf, MMRI, and EV-77 showed lower growth and composition in Cr-contaminated sand. The overall pattern of Z. mays cultivars grown in Cr-contaminated sand is as follows: Pearl > CZP > Sahiwal > YY > YH > EV-20 > Malka > EV-77 > MMRI-yellow > Sadaf. Conclusively, it can be identified that when grown in Cr-contaminated sand, Pearl, CZP, and Sahiwal have greater ability to grow in polluted soils. Overall, Z. mays cultivars showed better growth in Cr-stressed environment due to defense mechanism but further experiments needed to be conducted on molecular level.

Remediation of heavy metal polluted waters using activated carbon from lignocellulosic biomass: An update of recent trends

The use of a cheap and effective adsorption approach based on biomass-activated carbon (AC) to remediate heavy metal contamination is clearly desirable for developing countries that are economically disadvantaged yet have abundant biomass. Therefore, this review provides an update of recent works utilizing biomass waste-AC to adsorb commonly-encountered adsorbates like Cr, Pb, Cu, Cd, Hg, and As. Various biomass wastes were employed in synthesizing AC via two-steps processing; oxygen-free carbonization followed by activation. In recent works related to the activation step, the microwave technique is growing in popularity compared to the more conventional physical/chemical activation method because the microwave technique can ensure a more uniform energy distribution in the solid adsorbent, resulting in enhanced surface area. Nonetheless, chemical activation is still generally preferred for its ease of operation, lower cost, and shorter preparation time. Several mechanisms related to heavy metal adsorption on biomass wastes-AC were also discussed in detail, such as (i) - physical adsorption/deposition of metals, (ii) - ion-exchange between protonated oxygen-containing functional groups (-OH, -COOH) and divalent metal cations (M²⁺), (iii) - electrostatic interaction between oppositely-charged ions, (iv) - surface complexation between functional groups (-OH, O^2-, -CO-NH-, and -COOH) and heavy metal ions/complexes, and (v) - precipitation/co-precipitation technique. Additionally, key parameters affecting the adsorption performance were scrutinized. In general, this review offers a comprehensive insight into the production of AC from lignocellulosic biomass and its application in treating heavy metals-polluted water, showing that biomass-originated AC could bring great benefits to the environment, economy, and sustainability.

Removal of hexavalent chromium via biochar-based adsorbents: State-of-the-art, challenges, and future perspectives

Chromium originates from geogenic and extensive anthropogenic activities and significantly impacts natural ecosystems and human health. Various methods have been applied to remove hexavalent chromium (Cr(VI)) from aquatic environmental matrices, including adsorption via different adsorbents, which is considered to be the most common and low-cost approach. Biochar materials have been recognized as renewable carbon sorbents, pyrolyzed from various biomass at different temperatures under limited/no oxygen conditions for heavy metals remediation. This review summarizes the sources, chemical speciation & toxicity of Cr(VI) ions, and raw and modified biochar applications for Cr(VI) remediation from various contaminated matrices. Mechanistic understanding of Cr(VI) adsorption using different biochar-based materials through batch and saturated column adsorption experiments is documented. Electrostatic interaction and ion exchange dominate the Cr(VI) adsorption onto the biochar materials in acidic pH media. Cr(VI) ions tend to break down as HCrO₄^-, CrO₄^2-, and Cr₂O₇^2- ions in aqueous solutions. At low pH (∼1-4), the availability of HCrO₄^- ions attributes the electrostatic forces of attraction due to the available functional groups such as -NH₄⁺, -COOH, and -OH₂⁺, which encourages higher adsorption of Cr(VI). Equilibrium isotherm, kinetic, and thermodynamic models help to understand Cr(VI)-biochar interactions and their adsorption mechanism. The adsorption studies of Cr(VI) are summarized through the fixed-bed saturated column experiments and Cr-contaminated real groundwater analysis using biochar-based sorbents for practical applicability. This review highlights the significant challenges in biochar-based material applications as green, renewable, and cost-effective adsorbents for the remediation of Cr(VI). Further recommendations and future scope for the implications of advanced novel biochar materials for Cr(VI) removal and other heavy metals are elegantly discussed.

A Reverse Osmosis Process to Recover and Recycle Trivalent Chromium from Electroplating Wastewater

Electroplating generates high volumes of rinse water that is contaminated with heavy metals. This study presents an approach for direct metal recovery and recycling from simulated rinse water, made up of an electroplating electrolyte used in industry, using reverse osmosis (RO). To simulate the real industrial application, the process was examined at various permeate fluxes, ranging from 3.75 to 30 L·m−2·h−1 and hydraulic pressures up to 80 bar. Although permeance decreased significantly with increasing water recovery, rejections of up to 93.8% for boric acid, >99.9% for chromium and 99.6% for sulfate were observed. The final RO retentate contained 8.40 g/L chromium and was directly used in Hull cell electroplating tests. It was possible to deposit cold-hued chromium layers under a wide range of relevant current densities, demonstrating the reusability of the concentrate of the rinsing water obtained by RO.

Metallic nanoparticles for catalytic reduction of toxic hexavalent chromium from aqueous medium: A state-of-the-art review

The ever increasing concentration of toxic and carcinogenic hexavalent chromium (Cr (VI)) in various environmental mediums including water-bodies due to anthropogenic activities with rapid civilization and industrialization have become the major issue throughout the globe during last few decades. Therefore, developing new strategies for the treatment of Cr(VI) contaminated wastewaters are in great demand and have become a topical issue in academia and industry. To date, various techniques have been used for the remediation of Cr(VI) contaminated wastewaters including solvent extraction, adsorption, catalytic reduction, membrane filtration, biological treatment, coagulation, ion exchange and photo-catalytic reduction. Among these methods, the transformation of highly toxic Cr(VI) to benign Cr(III) catalyzed by metallic nanoparticles (M-NPs) with reductant has gained increasing attention in the past few years, and is considered to be an effective approach due to the superior catalytic performance of M-NPs. Thus, it is a timely topic to review this emerging technique for Cr(VI) reduction. Herein, recent development in synthesis of M-NPs based non-supported, supported, mono-, bi- and ternary M-NPs catalysts, their characterization and performance for the reduction of Cr(VI) to Cr(III) are reviewed. The role of supporting host to stabilize the M-NPs and leading to enhance the reduction of Cr(VI) are discussed. The Cr(VI) reduction mechanism, kinetics, and factors affecting the kinetics are overviewed to collect the wealthy kinetics data. Finally, the challenges and perspective in Cr(VI) reduction catalyzed by M-NPs are proposed. We believe that this review will assist the researchers who are working to develop novel M-NPs catalysts for the reduction of Cr(VI).

Morphological and Proteomic Analyses of Soybean Seedling Interaction Mechanism Affected by Fiber Crosslinked with Zinc-Oxide Nanoparticles

Nanoparticles (NPs) enhance soybean growth; however, their precise mechanism is not clearly understood. To develop a more effective method using NPs for the enhancement of soybean growth, fiber crosslinked with zinc oxide (ZnO) NPs was prepared. The solution of ZnO NPs with 200 nm promoted soybean growth at the concentration of 10 ppm, while fibers crosslinked with ZnO NPs promoted growth at a 1 ppm concentration. Soybeans grown on fiber cross-linked with ZnO NPs had higher Zn content in their roots than those grown in ZnO NPs solution. To study the positive mechanism of fiber crosslinked with ZnO NPs on soybean growth, a proteomic technique was used. Proteins categorized in photosynthesis and secondary metabolism accumulated more in soybeans grown on fiber crosslinked with ZnO NPs than in those grown in ZnO NPs solution. Furthermore, significantly accumulated proteins, which were NADPH oxidoreductase and tubulins, were confirmed using immunoblot analysis. The abundance of NADPH oxidoreductase increased in soybean by ZnO NPs application. These results suggest that fiber crosslinked with ZnO NPs enhances soybean growth through the increase of photosynthesis and secondary metabolism. Additionally, the accumulation of NADPH oxidoreductase might relate to the effect of auxin with fiber crosslinked with ZnO NPs on soybean growth.

Reviewing variables and their implications affecting adsorption of Cr(VI) onto activated carbon: an in-depth statistical case study

Removal of Cr(VI) from the aqueous phase using numerous activated carbons (AC) has been broadly studied in the last decades. Nevertheless, the diversity of activation methods, AC properties, and adsorption conditions precludes the standardization of specific characteristics required to achieve better adsorption results. This work reviewed the pertinent literature on Cr(VI) adsorption onto AC published over the past four decades. Pearson's correlation matrix and principal component analysis (PCA) assisted in identifying the parameters and AC characteristics that have the greatest influence on the maximum adsorption capacity (q_m). Two hundred thirty-six adsorption assays were found reporting data on 110 ACs and different parameters. Of these, 39.8% of the studies contemplated the variables q_m, pH, temperature (T), surface area (S_BET), micropore volume (V_micro), and mesopore volume (V_meso), and only 19.5% reported the point of zero charge (pH_PZC). Statistical analysis disclosed that S_BET and V_micro have a strong positive correlation with q_m, while V_meso, T, and pH show little or no correlation. The difference between pH and pH_PZC (PZC_diff) indicated a significant anticorrelation with q_m, thus evidencing that lower PZC_diff values enhance adsorption. The findings are useful for all researchers that work with Cr(VI) adsorption on AC since they provide a start point concerning the required adsorbent characteristics and process conditions to be employed.

Zinc Oxide Nanoparticles and Their Biosynthesis: Overview

Zinc (Zn) is plant micronutrient, which is involved in many physiological functions, and an inadequate supply will reduce crop yields. Its deficiency is the widest spread micronutrient deficiency problem; almost all crops and calcareous, sandy soils, as well as peat soils and soils with high phosphorus and silicon content are expected to be deficient. In addition, Zn is essential for growth in animals, human beings, and plants; it is vital to crop nutrition as it is required in various enzymatic reactions, metabolic processes, and oxidation reduction reactions. Finally, there is a lot of attention on the Zn nanoparticles (NPs) due to our understanding of different forms of Zn, as well as its uptake and integration in the plants, which could be the primary step toward the larger use of NPs of Zn in agriculture. Nanotechnology application in agriculture has been increasing over recent years and constitutes a valuable tool in reaching the goal of sustainable food production worldwide. A wide array of nanomaterials has been used to develop strategies of delivery of bioactive compounds aimed at boosting the production and protection of crops. ZnO-NPs, a multifunctional material with distinct properties and their doped counterparts, were widely being studied in different fields of science. However, its application in environmental waste treatment and many other managements, such as remediation, is starting to gain attention due to its low cost and high productivity. Nano-agrochemicals are a combination of nanotechnology with agrochemicals that have resulted in nano-fertilizers, nano-herbicides, nano-fungicides, nano-pesticides, and nano-insecticides being developed. They have anti-bacterial, anti-fungal, anti-inflammatory, antioxidant, and optical capabilities. Green approaches using plants, fungi, bacteria, and algae have been implemented due to the high rate of harmful chemicals and severe situations used in the manufacturing of the NPs. This review summarizes the data on Zn interaction with plants and contributes towards the knowledge of Zn NPs and its impact on plants.

Study on the mechanism of biochar loaded typical microalgae Chlorella removal of cadmium

Coconut shell activated carbon (Csac) is one of the most widely used materials to remove cadmium (Cd) from contaminated water. A large diversity of microorganisms exists in various aquatic systems and may aid Cd removal by Csac. In this study, we explored the reactions of Csac with microalgae (Chlorella) in Cd-containing media. The results of scanning electron microscope (SEM) imaging, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), superconducting pulse-Fourier transform nuclear magnetic resonance (pulse-FT NMR) and X-ray photoelectron spectroscopy (XPS) indicated that Chlorella could adhere in the micropores of Csac formed Csac@Chlorella composite adsorbent loading Chlorella. Furthermore, the composite adsorbent surface had abundant functional groups such -COOH, -OH and C-O-C, which served as active sites during the adsorption process. Compared with Csac, Csac@Chlorella had an enhanced Cd adsorption capacity evidently. The results showed that pH 8, 0.2 g Csac, OD₆₈₀ of 0.1 for Chlorella were optimal conditions for maximum Cd adsorption capacity within one hour contact time. Furthermore, the Cd adsorption process was well described by the pseudo-second-order and Langmuir adsorption isotherm models. The models revealed that the adsorption process was mainly based on chemical adsorption of a single molecular layer, accompanied by electrostatic attraction, complexation and intracellular adsorption, amongst other parameters. Collectively, the findings illustrate that the microalgae (Chlorella)-Csac-Cd interaction is complex and will thus have immense interest to a broad range of biological, environmental, and geoscience communities.

Polypyrrole-based adsorbents for Cr(VI) ions remediation from aqueous solution: a review

Anthropogenic activities are principally responsible for the manifestation of toxic and carcinogenic hexavalent chromium (Cr(VI)) triggering water pollution that threatens the environment and human health. The World Health Organisation (WHO) restricts Cr(VI) ion concentration to 0.1 and 0.05 mg/L in inland surface water and drinking water, respectively. The available technologies for Cr(VI) ion removal from water were highlighted with an emphasis on the adsorption technology. Furthermore, the characteristics of several polypyrrole-based adsorbents were scrutinized including amino-containing compounds, biosorbents, graphene/graphene oxide, clay materials and many other additives with reported effective Cr(VI) ion uptake. This efficiency in Cr(VI) ions adsorption is attributed to enhanced redox properties, increased number of functional groups as well as the synergistic behaviour of the materials making up the composites. The Langmuir isotherm best described the adsorption processes with maximum adsorption capacities ranging from 3.40-961.50 mg/g. The regeneration of Cr(VI) ion-laden adsorbents was studied. Ion exchange, electrostatic attractions, complexation, chelation reactions with protonated sites and reduction were the mechanisms of adsorption. Nevertheless, there are limited details on comprehensive adsorbent regeneration studies to prolong robustness in adsorption-desorption cycles and utilization of the Cr(VI) ion-laden adsorbent in other areas of research to limit the threat of secondary pollution.

Recycling of zinc ions in disc-donut column considering forward mixing mass transfer, and effects of pulsed and non-pulsed condition

The current study focuses on the recovery of zinc ions by solvent extraction in the pulsed contactor. The Zn(II) ions from chloride solution were extracted into the organic phase containing di-(2-ethylhexyl) phosphoric acid (D2EHPA) extractant. The resulting data were characterized for the relative amount of (a) pulsed and no-pulsed condition; and (b) flow rate of both phases. Based on the mass balance equations for the column performance description, numerical computations of mass transfer in a disc-donut column were conducted and validated the experimental data for zinc extraction. Four different models, such as plug flow, backflow, axial dispersion, and forward mixing were evaluated in this study. The results showed that the intensification of the process with the pulsed condition increased and achieved higher mass transfer rates. The forward mixing model findings based on the curve fitting approach validated well with the experimental data. The results showed that an increase in pulsation intensity, as well as the phase flow rates, have a positive impact on the performance of the extractor. In contrast, the enhancement of flow rate led to the reduction of the described model parameters for the adverse phase.

Nanocellulose and Graphene Oxide Aerogels for Adsorption and Removal Methylene Blue from an Aqueous Environment

The characteristics of aerogel materials such as the low density and large surface area enable them to adsorb large amounts of substances, so they show great potential for application in industrial wastewater treatment. Herein, using a combination of completely environmentally friendly materials such as cellulose nanofibers (CNFs) extracted from the petioles of the nipa palm tree and graphene oxide (GO) fabricated by simple solvent evaporation, a composite aerogel was prepared by a freeze-drying method. The obtained aerogel possessed a light density of 0.0264 g/cm3 and a porosity of more than 98.2%. It was able to withstand a weight as much as 2500 times with the maximum force (1479.5 N) to break up 0.2 g of an aerogel by compression strength testing and was stable in the aquatic environment, enabling it to be reused five times with an adsorption capacity over 90%. The CNF/GO aerogel can recover higher than 85% after 30 consecutive compression recovery cycles, which is convenient for the reusability of this material in wastewater treatments. The obtained aerogel also showed a good interaction between the component phases, a high thermal stability, a 3D network structure combined with thin walls and pores with a large specific surface area. In addition, the aerogel also exhibited a fast adsorption rate for methylene blue (MB) adsorption, a type of waste from the textile industry that pollutes water sources, and it can adsorb more than 99% MB in water in less than 20 min. The excellent adsorption of MB onto the CNF/GO aerogel was driven by electrostatic interactions, which agreed with the pseudo-second-order kinetic model with a correlation coefficient R 2 = 0.9978. The initial results show that the CNF/GO aerogel is a highly durable "green" light material that might be applied in the treatment of domestic organic waste water and is completely recoverable and reusable.

Combined application of zinc and iron-lysine and its effects on morpho-physiological traits, antioxidant capacity and chromium uptake in rapeseed (Brassica napus L.)

Environmental contamination of chromium (Cr) has gained substantial consideration worldwide because of its high levels in the water and soil. A pot experiment using oil seed crop (rapeseed (Brassica napus L.)) grown under different levels of tannery wastewater (0, 33, 66 and 100%) in the soil using the foliar application of zinc (Zn) and iron (Fe)-lysine (lys) has been conducted. Results revealed that a considerable decline in the plant growth and biomass elevates with the addition of concentrations of tannery wastewater. Maximum decline in plant height, number of leaves, root length, fresh and dry biomass of root and leaves were recorded at the maximum level of tannery wastewater application (100%) compared to the plants grown without the addition of tannery wastewater (0%) in the soil. Similarly, contents of carotenoid and chlorophyll, gas exchange parameters and activities of various antioxidants (superoxidase dismutase (SOD), peroxidase (POD), catalase (CAT) and ascorbate peroxidase (APX)) were also reduced significantly (P < 0.05) with the increasing concentration of tannery wastewater (33, 66 and 100%) in the soil. In addition, a combined application of Zn and Fe-lys reduced the accumulation and uptake of toxic Cr, while boosting the uptake of essential micronutrients such as Zn and Fe in different tissues of the plants. Results concluded that exogenous application of micronutrients chelated with amino acid successfully mitigate Cr stress in B. napus. Under field conditions, supplementation with these micronutrient-chelated amino acids may be an effective method for alleviating metal stress in other essential seed crops.

Cellulose: A Fascinating Biopolymer for Hydrogel Synthesis

The growing environmental concerns and increasing demands for eco-friendly materials have obliged researchers worldwide to explore naturally occurring biopolymers for various applications. Cellulose is a non-exhaustible polysaccharide biopolymer available almost...

Individual and combinatorial effects of SNP and NaHS on morpho-physio-biochemical attributes and phytoextraction of chromium through Cr-stressed spinach (Spinacia oleracea L.)

Chromium (Cr) is a toxic heavy metal that contaminates soil and water resources after its discharge from different industries. A pot experiment was conducted to determine the effects of single and/or combined application of sodium nitroprusside (SNP) (250 μM) and sodium hydrogen sulfide (NaHS) (1 mM) on growth, photosynthetic pigments, gas exchange characteristics, oxidative stress biomarkers, antioxidant machinery (enzymatic and non-enzymatic antioxidants), ion uptake, organic acid exudation, and Cr uptake of spinach (Spinacia oleracea L.) exposed to severe Cr stress [Cr: 0 (no Cr), 150, and 300 μM]. Our results depicted that Cr addition to the soil significantly (P < 0.05) decreased plant growth and biomass, gas exchange attributes, and mineral uptake by S. oleracea when compared to the plants grown without the addition of Cr. However, Cr toxicity boosted the production of reactive oxygen species (ROS) by increasing the content of malondialdehyde (MDA), which is the indication of oxidative stress in S. oleracea, and was also manifested by hydrogen peroxide (H₂O₂) content and electrolyte leakage to the membrane-bound organelles. The results showed that the activities of various antioxidative enzymes, such as superoxidase dismutase (SOD), peroxidase (POD), catalase (CAT), and ascorbate peroxidase (APX), and the content of non-enzymatic antioxidants, such as phenolic, flavonoid, ascorbic acid, and anthocyanin, initially increased with an increase in the Cr concentration in the soil. The results also revealed that the levels of soluble sugar, reducing sugar, and non-reducing sugar were decreased in plants grown under elevating Cr levels, but the accumulation of the metal in the roots and shoots of S. oleracea, was found to be increased, and the values of bioaccumulation factor were <1 in all the Cr treatments. The negative impacts of Cr injury were reduced by the application of SNP and NaHS (individually or combined), which increased plant growth and biomass, improved photosynthetic apparatus, antioxidant enzymes, and mineral uptake, as well as diminished the exudation of organic acids and oxidative stress indicators in roots of S. oleracea by decreasing Cr toxicity. Here, we conclude that the application of SNP and NaHS under the exposure to Cr stress significantly improved plant growth and biomass, photosynthetic pigments, and gas exchange characteristics; regulated antioxidant defense system and essential nutrient uptake; and balanced organic acid exudation pattern in S. oleracea.

The removal of arsenic and metals from highly acidic water in horizontal subsurface flow constructed wetlands with alternative supporting media

A laboratory-scale horizontal subsurface flow constructed wetland system was used to quantify the arsenic removal capacity in the treatment of highly acidic, arsenic and metal-rich water: pH ≈ 2, Fe ≈ 57 mg/L, Pb ≈ 0.9 mg/L, Zn ≈ 12 mg/L. The system was operated in two stages, being As ≈ 2.1 mg/L in stage one, and ≈ 3.7 mg/L in stage 2. Limestone and zeolite were employed as main supporting media to build non-vegetated and vegetated cells with Phragmites australis. The system was very effective in the removal of arsenic and iron (> 96%), and lead (> 94%) throughout the whole experimental period, having the four treatment types a similar performance. The main effect of the media type was on the pH adjustment capacity: limestone cells were able to raise the pH to ≈ 7.1, whereas zeolite cells raised it to ≈ 3.8. The contribution of plant uptake to the overall removal of As, Fe and Zn was minor; accounting for less than 0.02%, 0.07% and 0.7% respectively. As such, pollutants were mainly retained in the wetland beds. Our results suggest that limestone is recommended over zeolite as wetland medium mainly due to its neutralization capacity.