Wastewater treatment systems harbor specific and diverse yeast communities

Recent advances in eco-friendly technology for decontamination of pulp and paper mill industrial effluent: a review

The economic development of a country directly depends upon industries. But this economic development should not be at the cost of our natural environment. A substantial amount of water is spent during paper production, creating water scarcity and generating wastewater. Therefore, the Pollution Control Board classifies this industry into red category. Water is used in different papermaking stages such as debarking, pulping or bleaching, washing, and finishing. The wastewater thus generated contains lignin and xenobiotic compounds such as resin acids, chlorinated lignin, phenols, furans, dioxins, chlorophenols, adsorbable organic halogens (AOX), extractable organic halogens (EOCs), polychlorinated biphenyls, plasticizers, and polychlorinated dibenzodioxins. Nowadays, several microorganisms are used in the detoxification of these hazardous effluents. Researchers have found that microbial degradation is the most promising treatment method to remove high biological oxygen demand (BOD) and chemical oxygen demand (COD) from wastewater. Microorganisms also remove AOX toxicity, chlorinated compounds, suspended solids, color, lignin, derivatives, etc. from the pulp and paper mill effluents. But in the current scenario, mill effluents are known to deteriorate the environment and therefore it is highly desirable to deploy advanced technologies for effluent treatment. This review summarizes the eco-friendly advanced treatment technologies for effluents generated from pulp and paper mills.

Plant microbe based remediation approaches in dye removal: A review

Increased industrialization demand using synthetic dyes in the newspaper, cosmetics, textiles, food, and leather industries. As a consequence, harmful chemicals from dye industries are released into water reservoirs with numerous structural components of synthetic dyes, which are hazardous to the ecosystem, plants and humans. The discharge of synthetic dye into various aquatic environments has a detrimental effect on the balance and integrity of ecological systems. Moreover, numerous inorganic dyes exhibit tolerance to degradation and repair by natural and conventional processes. So, the present condition requires the development of efficient and effective waste management systems that do not exacerbate environmental stress or endanger other living forms. Numerous biological systems, including microbes and plants, have been studied for their ability to metabolize dyestuffs. To minimize environmental impact, bioremediation uses endophytic bacteria, which are plant beneficial bacteria that dwell within plants and may improve plant development in both normal and stressful environments. Moreover, Phytoremediation is suitable for treating dye contaminants produced from a wide range of sources. This review article proves a comprehensive evaluation of the most frequently utilized plant and microbes as dye removal technologies from dye-containing industrial effluents. Furthermore, this study examines current existing technologies and proposes a more efficient, cost-effective method for dye removal and decolorization on a big scale. This study also aims to focus on advanced degradation techniques combined with biological approaches, well regarded as extremely effective treatments for recalcitrant wastewater, with the greatest industrial potential.

Removal of color from pulp and paper mill wastewater- methods and techniques- A review

The pulp and paper industry consumes a huge amount of water and releases more polluted and colored wastewater every year. Many conventional techniques are used in the treatment of paper industry wastewater. However, for color removal from paper mill effluent, there is no proven method so far, on an industrial scale. Due to high energy input and high cost, there is an urgent need to find out a new technique that must be sustainable, economical, and environment friendly. Various methods have been investigated on bench scale and pilot scale also but no proven method for color removal on an industrial scale. The paper provides an overview of the color removal techniques from different sources of pulp and paper mill wastewater discharged by various industries. The review described various components involved in various processes for color removal from paper mill waste water. The present works focus on processes like chemical, chemical/physical, biological, physicochemical, and electrochemical applied in color removal from paper mill wastewater. The present review gives key information on the effectiveness, use, betterment, and limitations of numerous methods of treatment targeted at color removal from paper mill wastewater using various techniques still under evolution.

Categorisation of culturable bioaerosols in a fruit juice manufacturing facility

Bioaerosols are defined as aerosols that comprise particles of biological origin or activity that may affect living organisms through infectivity, allergenicity, toxicity, or through pharmacological or other processes. Interest in bioaerosol exposure has increased over the last few decades. Exposure to bioaerosols may cause three major problems in the food industry, namely: (i) contamination of food (spoilage); (ii) allergic reactions in individual consumers; or (iii) infection by means of pathogenic microorganisms present in the aerosol. The aim of this study was to characterise the culturable fraction of bioaerosols in the production environment of a fruit juice manufacturing facility and categorise isolates as harmful, innocuous or potentially beneficial to the industry, personnel and environment. Active sampling was used to collect representative samples of five areas in the facility during peak and off-peak seasons. Areas included the entrance, preparation and mixing area, between production lines, bottle dispersion and filling stations. Microbes were isolated and identified using 16S, 26S or ITS amplicon sequencing. High microbial counts and species diversity were detected in the facility. 239 bacteria, 41 yeasts and 43 moulds were isolated from the air in the production environment. Isolates were categorised into three main groups, namely 27 innocuous, 26 useful and 39 harmful bioaerosols. Harmful bioaerosols belonging to the genera Staphylococcus, Pseudomonas, Penicillium and Candida were present. Although innocuous and useful bioaerosols do not negatively influence human health their presence act as an indicator that an ideal environment exists for possible harmful bioaerosols to emerge.

Evaluation of the Abundance of Fungi in Wastewater Treatment Plants Using Quantitative PCR (qPCR)

Assessment of the abundance of fungi in environmental samples by quantitative PCR (qPCR) of community DNA is often a difficult task due to biases introduced during PCR amplification, resulting from the differences associated with length polymorphism and the varying number of copies of the rRNA operon among fungal species, the lack of specificity of the primers targeting the different regions of the rRNA operon, or their insufficient coverage of the fungal lineages. To overcome those limitations, it is crucial to test and select the specific primers sets which provide the more accurate approximation to the quantification of the targeted fungal populations in a given set of samples. Fungi are a significant fraction of the microbiota in wastewater treatment plants (WWTPs), but the activated sludge microbial communities comprise many other eukaryotic microorganisms whose molecular markers are often coamplified by primers initially designed as fungal-specific. Here, the use of the FungiQuant primer set is recommended for the quantification of fungal molecular markers (18S rRNA genes) by qPCR in activated sludge samples and the full protocol is described.

Preparation, Performances, and Mechanisms of Microbial Flocculants for Wastewater Treatment

In recent years, close attention has been paid to microbial flocculants because of their advantages, including safety to humans, environmental friendliness, and acceptable removal performances. In this review, the preparation methods of microbial flocculants were first reviewed. Then, the performances of bioflocculants in the removal of suspended solids, heavy metals, and other organic pollutants from various types of wastewater were described and commented, and the removal mechanisms, including adsorption bridging, charge neutralization, chemical reactions, and charge neutrality, were also discussed. The future research needs on microbial flocculants were also proposed. This review would lead to a better understanding of current status, challenges, and corresponding strategies on microbial flocculants and bioflocculation in wastewater treatment.

Diversity, Co-occurrence and Implications of Fungal Communities in Wastewater Treatment Plants

Three wastewater treatment plants (WWTPs) located in Gauteng province in South Africa were investigated to determine the diversity, co-occurrence and implications of their fungal communities using illumina sequencing platform and network analysis. Phylogenetic taxonomy revealed that members of the fungal communities were assigned to 6 phyla and 361 genera. Basidiomycota and Ascomycota were the most abundant phyla, dominated by the genera Naumovozyma, Pseudotomentella, Derxomyces, Ophiocordyceps, Pulchromyces and Paecilomyces. Phylogenetic analysis revealed the existence of fungal OTUs related to class lineages such as Agaricomycetes, Eurotiomycetes and Sordariomycetes indicating new fungal diversity in WWTPs. Dominant and rare fungal genera that can potentially be used in bioremediation such as Trichoderma, Acremonium, Talaromyces, Paecilomyces, cladophialophora and Saccharomyces were detected. Conversely, genera whose members are known to be pathogenic to human and plant such as Olpidium, Paecilomyces, Aspergillus, Rhodotorula, Penicillium, Candida, Synchytrium, Phyllosticta and Mucor were also detected in all WWTPs. Phylotype analysis confirmed that some fungal phylotypes were highly similar to the reported fungal pathogens of concern. Co-occurrence network analysis revealed that the fungal genera such as Minimedusa, Glomus, Circinella, Coltricia, Caloplaca, Phylosticta, Peziza, Candida, and Hydnobolites were the major networking hub in the WWTPs. The overall results in this study highlighted that WWTPs represent a potential source of beneficial fungi for bioremediation of pollutants in the ecosystem and the need to consider human and plant fungal pathogens during safety evaluation of treated wastewater for reuse.

Aquatic bacterial contamination associated with sugarplant sewage outfalls as a microbial hazard for fish

The aim of the study was to compare bacterial composition and load in waters and fish related to the wastewater treatment plant (WWTP), particularly waters and wild fish affected by sugarplant processing (sugar cane and sugar beet). Aeromonads were the most frequently isolated group from water and fish. A. hydrophila was a prevailing species in isolates from water, followed by A. veronii, Rheinheimera soli and Ochrobactrum anthropi. Of indicator bacteria for aquatic contamination from fish tissues, the most prominent were V. cholerae, Enterobacter cloacae and E. sakazakii. Sugar cane processing contributed to high viable cell counts at 37 °C while sugar beet processing contributed to high bacterial counts at 22 °C. Heterotrophs from gills of effluent fish were highest during sugar cane processing. Counts retrieved from fish skin were more uniform between effluent fish and fish from downstream waters. Antimicrobial resistance of bacteria isolated from water was high against amoxicillin, sulfamethoxazole, flumequine, norfloxacin and oxolinic acid in samples from the inflow of raw municipal wastewaters to WWTP, while resistance found in bacteria from the inflow of sugarplant mostly related to sulfamethoxazole and amoxicillin. The PCA analysis associated the occurrence of high heterotroph counts, P. aeruginosa, and intestinal enterococci on skin and gills with sugar cane, and yeasts and molds with sugar beet processing. Fish living in treated wastewaters and related water bodies could pose a microbial hazard if fished for human consumption, possibly causing infection when being handled and processed, as a risk of human pathogens penetrating fish tissues.

Mediterranean forested wetlands are yeast hotspots for bioremediation: a case study using azo dyes

Forested wetlands are interfaces between terrestrial and aquatic environments. These ecosystems play an important role in the hydrology, chemistry and biodiversity maintenance. Despite their high microbial diversity, there has been a lack of attention to the potential of their yeast communities. The purpose of this study is to evaluate the potential of yeasts isolated from a Mediterranean forested wetlands in decolorizing azo dyes. Azo dyes are synthetic, and highly recalcitrant to degradation. Ninety-two out of 560 isolates were randomly chosen to assess their ability to decolorize five azo dyes. Hierarchical clustering based on medium color changes during incubations was used to evaluate the isolates’ decolorization performance. All of the isolates that best degraded the 5 dyes tested were identified as Basidiomycota (Filobasidiales, Tremellales and Sporidiobolales). This work identifies new azo dye-degrading yeast species, and supports the hypothesis that forested wetlands are a niche for yeasts with bioremediation potential - namely azo dyes removal.

Assessing the abundance of fungal populations in a full-scale membrane bioreactor (MBR) treating urban wastewater by using quantitative PCR (qPCR)

The abundance of fungi in a full-scale membrane bioreactor (MBR) treating urban wastewater and experiencing seasonal foaming was assessed by quantitative PCR (qPCR), comparing three different sets of widely used universal fungal primers targeting the gene encoding the small ribosomal subunit RNA, 18S-rDNA, (primers NS1-Fung and FungiQuant) or the internal transcribed spacer ITS2 (primers ITS3-ITS4). Fungi were a numerically important fraction of the MBR microbiota (≥10⁶ 18S-rDNA copies/L activated sludge), and occurred both in the aerated and anoxic bioreactors. The numbers of copies of fungal markers/L activated sludge calculated using the NS1-Fung or ITS3-ITS4 primer sets were up to 2 orders of magnitude higher than the quantifications based on the FungiQuant primers. Fungal 18S-rDNA counts derived from the FungiQuant primers decreased significantly during cold seasons, concurring with foaming episodes in the MBR. Redundancy analysis corroborated that temperature was the main factor driving fungi abundance, which was also favored by longer solid retention time (SRT), lower chemical oxygen demand/biochemical oxygen demand at 5 days (COD/BOD₅) of influent water, and lower biomass accumulation in the MBR.

Study of the effect of the bacterial and fungal communities present in real wastewater effluents on the performance of fungal treatments

The use of the ligninolytic fungi Trametes versicolor for the degradation of micropollutants has been widely studied. However, few studies have addressed the treatment of real wastewater containing pharmaceutically active compounds (PhAC) under non-sterile conditions. The main drawback of performing such treatments is the difficulty for the inoculated fungus to successfully compete with the other microorganisms growing in the bioreactor. In the present study, several fungal treatments were performed under non-sterile conditions in continuous operational mode with two types of real wastewater effluent, namely, a reverse osmosis concentrate (ROC) from a wastewater treatment plant and a veterinary hospital wastewater (VHW). In all cases, the setup consisted of two parallel reactors: one inoculated with T. versicolor and one non-inoculated, which was used as the control. The main objective of this work was to correlate the operational conditions and traditional monitoring parameters, such as laccase activity, with PhAC removal and the composition of the microbial communities developed inside the bioreactors. For that purpose a variety of biochemical and molecular biology analyses were performed: phospholipid fatty acids analysis (PLFA), quantitative PCR (qPCR) and denaturing gradient gel electrophoresis (DGGE) followed by sequencing. The results show that many indigenous fungi (and not only bacteria, which were the focus of the majority of previously published research) can successfully compete with the inoculated fungi (i.e., Trichoderma asperellum overtook T. versicolor in the ROC treatment). We also showed that the wastewater origin and the operational conditions had a stronger impact on the diversity of microbial communities developed in the bioreactors than the inoculation or not with T. versicolor.

Community structure, population dynamics and diversity of fungi in a full-scale membrane bioreactor (MBR) for urban wastewater treatment

Community structure, population dynamics and diversity of fungi were monitored in a full-scale membrane bioreactor (MBR) operated throughout four experimental phases (Summer 2009, Autumn 2009, Summer 2010 and Winter, 2012) under different conditions, using the 18S-rRNA gene and the intergenic transcribed spacer (ITS2-region) as molecular markers, and a combination of temperature-gradient gel electrophoresis and 454-pyrosequencing. Both total and metabolically-active fungal populations were fingerprinted, by amplification of molecular markers from community DNA and retrotranscribed RNA, respectively. Fingerprinting and 454-pyrosequencing evidenced that the MBR sheltered a dynamic fungal community composed of a low number of species, in accordance with the knowledge of fungal diversity in freshwater environments, and displaying a medium-high level of functional organization with few numerically dominant phylotypes. Population shifts were experienced in strong correlation with the changes of environmental variables and operation parameters, with pH contributing the highest level of explanation. Phylotypes assigned to nine different fungal Phyla were detected, although the community was mainly composed of Ascomycota, Basidiomycota and Chytridiomycota/Blastocladiomycota. Prevailing fungal phylotypes were affiliated to Saccharomycetes and Chytridiomycetes/Blastocladiomycetes, which displayed antagonistic trends in their relative abundance throughout the experimental period. Fungi identified in the activated sludge were closely related to genera of relevance for the degradation of organic matter and trace-organic contaminants, as well as genera of dimorphic fungi potentially able to produce plant operational issues such as foaming or biofouling. Phylotypes closely related to genera of human and plant pathogenic fungi were also detected.

Performance and microbial community composition in a long-term sequential anaerobic-aerobic bioreactor operation treating coking wastewater

The combined anaerobic-aerobic biosystem is assumed to consume less energy for the treatment of high strength industrial wastewater. In this study, pollutant removal performance and microbial diversity were assessed in a long-term (over 300 days) bench-scale sequential anaerobic-aerobic bioreactor treating coking wastewater. Anaerobic treatment removed one third of the chemical oxygen demand (COD) and more than half of the phenols with hydraulic retention time (HRT) of 42 h, while the combined system with total HRT of 114 h removed 81.8, 85.6, 99.9, 98.2, and 85.4 % of COD, total organic carbon (TOC), total phenols, thiocyanate, and cyanide, respectively. Two-dimensional gas chromatography with time-of-flight mass spectrometry showed complete removal of phenol derivatives and nitrogenous heterocyclic compounds (NHCs) via the combined system, with the anaerobic process alone contributing 58.4 and 58.6 % removal on average, respectively. Microbial activity in the bioreactors was examined by 454 pyrosequencing of the bacterial, archaeal, and fungal communities. Proteobacteria (61.2-93.4 %), particularly Betaproteobacteria (34.4-70.1 %), was the dominant bacterial group. Ottowia (14.1-46.7 %), Soehngenia (3.0-8.2 %), and Corynebacterium (0.9-12.0 %), which are comprised of phenol-degrading and hydrolytic bacteria, were the most abundant genera in the anaerobic sludge, whereas Thiobacillus (6.6-43.6 %), Diaphorobacter (5.1-13.0 %), and Comamonas (0.2-11.1 %) were the major degraders of phenol, thiocyanate, and NHCs in the aerobic sludge. Despite the low density of fungi, phenol degrading oleaginous yeast Trichosporon was abundant in the aerobic sludge. This study demonstrated the feasibility and optimization of less energy intensive treatment and the potential association between abundant bacterial groups and biodegradation of key pollutants in coking wastewater.

Review on recent developments on pulp and paper mill wastewater treatment

Economic benefits of the pulp and paper industry have led it to be one of the most important industrial sections in the world. Nevertheless, in recent years, pulp and paper mills are facing challenges with the energy efficiency mechanisms and management of the resulting pollutants, considering the environmental feedbacks and ongoing legal requirements. This study reviews and discusses the recent developments of affordable methods dealing with pulp and paper mill wastewaters. To this end, the current state of the various processes used for pulp and paper production from virgin or recovered fibers has been briefly reviewed. Also, the relevant contaminants have been investigated, considering the used raw materials and applied techniques as the subject for further discussion about the relevant suitable wastewater treatment methods. The results of the present study indicated that adopting the integrated methods, alongside a combination of biological (e.g., anaerobic digestion) and physicochemical (e.g., novel Fenton reactions) treatment methods, can be environmentally and economically preferable to minimize environmental contaminants and energy recycling.

Membrane bioreactor wastewater treatment plants reveal diverse yeast and protist communities of potential significance in biofouling

The yeast community was studied in a municipal full-scale membrane bioreactor wastewater treatment plant (MBR-WWTP). The unexpectedly high diversity of yeasts indicated that the activated sludge formed a suitable environment for them to proliferate, with cellular concentrations of 2.2 ± 0.8 × 10(3) CFU ml(-1). Sixteen species of seven genera were present in the biological reactor, with Ascomycetes being the most prevalent group (93%). Most isolates were able to grow in a synthetic wastewater medium, adhere to polyethylene surfaces, and develop biofilms of variable complexity. The relationship between yeast populations and the protists in the MBR-WWTP was also studied, revealing that some protist species preyed on and ingested yeasts. These results suggest that yeast populations may play a role in the food web of a WWTP and, to some extent, contribute to membrane biofouling in MBR systems.

Winery wastewater treatment by combination of Cryptococcus laurentii and Fenton's reagent

Winery wastewaters (WW) have high levels of organic matter, resulting in high COD and BOD and suspended solids. This paper studies the combination of biological and chemical processes in WW treatment. Among 10 yeast isolates, Filobasidium sp. (AGG 577) and Cryptococcus laurentii (AGG 726) were selected due to their superior performance in COD removal. During WW degradation, COD and total polyphenols (TPP) content removal of 89-90% for Filobasidium sp. and 90-93% for C. laurentii were obtained. However, despite similar degradation efficiency for both yeasts, COD kinetics and pH evolution during treatment reveals that C. laurentii presents a faster response than Filobasidium sp. The toxicity (inhibition of Vibrio fischeri luminescence) of C. laurentii treated WW decreases to an inhibition value below 2.5%. However, treated WW exceeds the legal limits, making necessary an additional treatment. In this case, the selection of Fenton's reagent as a chemical final polish step process is a good compromise between efficiency and lower practical complexity. The best results for both COD and TPP removal were obtained with H2O2 initial concentration of 39.2mM and a H2O2:Fe(2+) molar ratio of 15:1. The combined C. laurentii - Fenton's reagent treatment of WW achieved a total reduction of 98% and 96%, for COD and TPP, respectively.

Mycological and ecotoxicological characterisation of landfill leachate before and after traditional treatments

Pollution caused by landfill leachates is one of the main problems of urbanised areas, on account of their chemical composition, which turn in an ineffective treatment. A characterisation of leachates, which takes into account chemical, ecotoxicological and mycological aspects, is basilar for the evaluation of environmental impact of leachate and the development of suitable treatment techniques. In this study, the toxicity of a raw leachate and an effluent coming from traditional wastewater treatment plant was assessed by means of 4 ecotoxicological assays. Both the samples exceed the legal threshold value according to all the tested organisms, indicating the ineffectiveness of activated sludge treatment in the reduction of toxicity. The autochthonous mycoflora of the two samples was evaluated by filtration. The fungal load was 73 CFU for leachate and 102 CFU for the effluent. Ascomycetes were the dominant fraction (81% and 61%, for leachate and effluent respectively), followed by basidiomycetes (19% and 39%, respectively). Most of them were potential emerging pathogens. A decolourisation screening with autochthonous fungi was set up towards both samples in the presence or absence of glucose. Eleven fungi (basidiomycetes and ascomycetes) achieved up to 38% decolourisation yields, showing to be promising fungi for the bioremediation of leachates. Further experiment will be aimed to the study of decolourisation mechanism and toxicity reduction.

Extracellular enzyme production and phylogenetic distribution of yeasts in wastewater treatment systems

The abilities of yeasts to produce different extracellular enzymes and their distribution characteristics were studied in municipal, inosine fermentation, papermaking, antibiotic fermentation, and printing and dyeing wastewater treatment systems. The results indicated that of the 257 yeasts, 16, 14, 55, and 11 produced lipase, protease, manganese dependant peroxidase (MnP), and lignin peroxidase (LiP), respectively. They were distributed in 12 identified and four unidentified genera, in which Candida rugosa (AA-M17) and an unidentified Saccharomycetales (AA-Y5), Pseudozyma sp. (PH-M15), Candida sp. (MO-Y11), and Trichosporon montevideense (MO-M16) were shown to have the highest activity of lipase, protease, Mnp, and LiP, respectively. No yeast had amylase, cellulose, phytase, or laccase activity. Although only 60 isolates produced ligninolytic enzymes, 249 of the 257 yeasts could decolorize different dyes through the mechanism of biodegradation (222 isolates) or bio-sorption. The types of extracellular enzymes that the yeasts produced were significantly shaped by the types of wastewater treated.