The effect of particle agglomeration on the formation of a surface-connected compartment induced by hydroxyapatite nanoparticles in human monocyte-derived macrophages

Fabrication of granular three-dimensional graphene oxide/UiO-66 adsorbent for high uranium adsorption: Density functional theory and fixed bed column studies

This study presents a thorough investigation of the novel application of graphene oxide (GO) modified with melamine formaldehyde to fabricate granular three-dimensional GO (3D-GO), followed by the introduction of UiO-66 doping (3D-GO/U) for high uranium (U) adsorption. The U(VI) adsorption isotherms revealed that 3D-GO/U-10 with 10 % UiO-66 incorporation exhibited an impressive adsorption capacity of 375.5 mg g-1 and remained high U(VI) sorption performance in wide pH range. The introduction of UiO-66 to 3D-GO (3D-GO/U-10) led to the deagglomeration of the UiO-66 particles. The in situ surface-enhanced-Raman-spectroscopy-analysis and density-functional-theory simulations showed the symmetric metal center site Zr-O2 on UiO-66 was discovered to exhibit the highest adsorption energy (-3.21 eV) for U(VI) species due to the electrons transfer from the oxygen atom to U(VI) drives the covalent bonding between the symmetric metal center sites Zr-O2 and U(VI) on 3D-GO/U-10. The 3D-GO/U-10 was regenerated using a 0.1 M Na2CO3/0.01 M H2O2 solution and achieved up to 89.7 % U(VI) removal in the 5th cycle. The continuous flow column experiments results revealed 3D-GO/U-10 can regenerate and maintain a U(VI) removal capacity of ∼76 % for up to 4 cycles column experiments. Therefore, 3D-GO/U-10 exhibits great potential for removing U(VI) from water bodies.

Bone Morphogenetic Protein 7-Loaded Gelatin Methacrylate/Oxidized Sodium Alginate/Nano-Hydroxyapatite Composite Hydrogel for Bone Tissue Engineering

Background

Bone tissue engineering (BTE) is a promising alternative to autologous bone grafting for the clinical treatment of bone defects, and inorganic/organic composite hydrogels as BTE scaffolds are a hot spot in current research. The construction of nano-hydroxyapatite/gelatin methacrylate/oxidized sodium alginate (nHAP/GelMA/OSA), abbreviated as HGO, composite hydrogels loaded with bone morphogenetic protein 7 (BMP7) will provide a suitable 3D microenvironment to promote cell aggregation, proliferation, and differentiation, thus facilitating bone repair and regeneration.

Methods

Dually-crosslinked hydrogels were fabricated by combining GelMA and OSA, while HGO hydrogels were formulated by incorporating varying amounts of nHAP. The hydrogels were physically and chemically characterized followed by the assessment of their biocompatibility. BMP7-HGO (BHGO) hydrogels were fabricated by incorporating suitable concentrations of BMP7 into HGO hydrogels. The osteogenic potential of BHGO hydrogels was then validated through in vitro experiments and using rat femoral defect models.

Results

The addition of nHAP significantly improved the physical properties of the hydrogel, and the composite hydrogel with 10% nHAP demonstrated the best overall performance among all groups. The selected concentration of HGO hydrogel served as a carrier for BMP7 loading and was evaluated for its osteogenic potential both in vivo and in vitro. The BHGO hydrogel demonstrated superior in vitro osteogenic induction and in vivo potential for repairing bone tissue compared to the outcomes observed in the blank control, BMP7, and HGO groups.

Conclusion

Using hydrogel containing 10% HGO appears promising for bone tissue engineering scaffolds, especially when loaded with BMP7 to boost its osteogenic potential. However, further investigation is needed to optimize the GelMA, OSA, and nHAP ratios, along with the BMP7 concentration, to maximize the osteogenic potential.

Size-dependent Effect on Foliar Utilization and Biocontrol Efficacy of Emamectin Benzoate Delivery Systems

The development of nanopesticides provides new avenues for pesticide reduction and efficiency improvement. However, the size effect of nanopesticides remains unclear, and its underlying mechanisms of influence have become a major obstacle in the design and application of pesticide nanoformulations. In this research, the noncarrier-coated emamectin benzoate (EB) solid dispersions (Micro-EB and Nano-EB) were produced under a constant surfactant-to-active ingredient ratio by a self-emulsifying-carrier solidification technique. The particle size of Micro-EB was 162 times that of spherical Nano-EB. The small size and large specific surface area of Nano-EB facilitated the adsorption of surfactants on the surface of the particles, thereby improving its dispersibility, suspensibility, and stability. The pinning effect of nanoparticles significantly suppressed droplet retraction and rebounding. Moreover, Nano-EB exhibited a 25% higher retention of the active ingredient on cabbage leaves and a 70% higher washing resistance than Micro-EB, and both were significantly different. The improvement of abilities in wetting, spreading, and retention of Nano-EB on crop leaves contributed to the increase in foliar utilization, which further resulted in a 1.6-fold enhancement of bioactivity against target Spodoptera exigua compared to Micro-EB. Especially, Nano-EB did not exacerbate the safety risk to the nontarget organism zebrafish with no significant difference. This study elaborates the size effect on the effectiveness and safety of pesticide formulations and lays a theoretical foundation for the development and rational utilization of efficient and environmentally friendly nanopesticides.

Preparation and Comprehensive Evaluation of the Efficacy and Safety of Chlorantraniliprole Nanosuspension

Chlorantraniliprole is a broad-spectrum insecticide that has been widely used to control pests in rice fields. Limited by its low solubility in both water and organic solvents, the development of highly efficient and environmentally friendly chlorantraniliprole formulations remains challenging. In this study, a low-cost and scalable wet media milling technique was successfully employed to prepare a chlorantraniliprole nanosuspension. The average particle size of the extremely stable nanosuspension was 56 nm. Compared to a commercial suspension concentrate (SC), the nanosuspension exhibited superior dispersibility, as well as superior foliar wetting and retention performances, which further enhanced its bioavailability against Cnaphalocrocis medinalis. The nanosuspension dosage could be reduced by about 40% while maintaining a comparable efficacy to that of the SC. In addition, the chlorantraniliprole nanosuspension showed lower residual properties, a lower toxicity to non-target zebrafish, and a smaller effect on rice quality, which is conducive to improving food safety and the ecological safety of pesticide formulations. In this work, a novel pesticide-reduction strategy is proposed, and theoretical and data-based support is provided for the efficient and safe application of nanopesticides.

Eco-friendly alkali lignin-assisted water-based graphene oxide ink and its application as a resistive temperature sensor

Inkjet-printable ink formulated with graphene oxide (GO) offers several advantages, including aqueous dispersion, low cost, and environmentally friendly production. However, water-based GO ink encounters challenges such as high surface tension, low wetting properties, and reduced ink stability over prolonged storage time. Alkali lignin, a natural surfactant, is promising in improving GO ink's stability, wettability, and printing characteristics. The concentration of surfactant additives is a key factor in fine-tuning GO ink's stability and printing properties. The current study aims to explore the detailed effects of alkali lignin concentration and optimize the overall properties of graphene oxide (GO) ink for drop-on-demand thermal inkjet printing. A meander-shaped temperature sensor electrode was printed using the optimized GO ink to demonstrate its practical applicability for commercial purposes. The sensing properties are evaluated using a simple experimental setup across a range of temperatures. The findings demonstrate a significant increase in zeta potential by 25% and maximum absorption by 84.3%, indicating enhanced stability during prolonged storage with an optimized alkali lignin concentration compared to the pure GO dispersions. The temperature sensor exhibits a remarkable thermal coefficient of resistance of 1.21 within the temperature range of 25 °C-52 °C, indicative of excellent sensitivity, response, and recovery time. These results highlight the potential of alkali lignin as a natural surfactant for improving the performance and applicability of inkjet-printable GO inks in various technological applications.

Effect of Salinity on Hydroxyapatite Nanoparticles Flooding in Enhanced Oil Recovery: A Mechanistic Study

Fluid-fluid interactions can affect any enhanced oil recovery (EOR) method, including nanofluid (NF) brine-water flooding. Flooding with NFs changes wettability and lowers oil-water interfacial tension (IFT). Preparation and modification affect the nanoparticle (NP) performance. Hydroxyapatite (HAP) NPs in EOR are yet to be properly verified. HAP was synthesized in this study using co-precipitation and in situ surface functionalization with sodium dodecyl sulfate in order to investigate its impact on EOR processes at high temperatures and different salinities. The following techniques were employed, in that sequence, to verify its synthesis: transmission electron microscopy, zeta potential, thermogravimetric analysis, Fourier transform infrared spectroscopy, X-ray diffraction, particle size analysis, and energy-dispersive X-ray spectra. The outcomes showed the production of HAP, with the particles being evenly dispersed and stable in aqueous solution. The particles' surface charge increased from -5 to -27 mV when the pH was changed from 1 to 13. The HAP NFs at 0.1 wt % altered the wettability of sandstone core plugs from oil-wet at 111.7 to water-wet at 9.0 contact angles at salinity ranges of 5000 ppm to 30,000 ppm. Additionally, the IFT was reduced to 3 mN/m HAP with an incremental oil recovery of 17.9% of the initial oil in place. The HAP NF thus demonstrated excellent effectiveness in EOR through IFT reduction, wettability change, and oil displacement in both low and high salinity conditions.

Bioaccessibility, source and human health risk of Pb, Cd, Cu and Zn in windowsill dusts from an area affected by long-term Pb smelting

Non-ferrous metal smelting results in heterogenous spatial distribution of potentially toxic metals (PTM) near smelters. In this work, windowsill dusts were collected from smelting (SA) and urban (UJ) sub-areas of Jiyuan (a city affected by >70 years of Pb smelting) to investigate PTM source and bioaccessibility. The <10 μm fraction of dusts were analyzed for total and bioaccessible Pb, Cd, Cu and Zn concentrations; bioaccessibility was analyzed by a three-stage assay (i.e., lung phase, gastric phase and gastrointestinal phase) using artificial lysosomal fluid (ALF, L phase) followed by simulated gastric and gastrointestinal fluids (G and GI phases). This assay mimicked the movement of particles phagocytosed by alveolar macrophages in the respiratory system, then transported up the oropharynx and subsequently swallowed and transported into the digestive system. Zinc had greater bioaccessible concentrations in L and GI phases than other metals, and the mean L phase bioaccessible PTM concentrations in SA were greater than in UJ. The mean L + GI phase bioaccessible concentrations of Pb, Cd, Cu and Zn in SA were 280, 79, 124 and 1458 mg kg^-1, while those in UJ were 215, 54, 116 and 598 mg kg^-1, respectively. The L phase extracted 87.7 to 98.8 % of PTM within the L + GI assay. Lead had a lower L + GI bioaccessibility than Cd, Cu and Zn (70-76 % vs. 82-92 %). Higher tolerable Cd carcinogenic risks based on bioaccessibility were found in SA sub-area than in UJ while no carcinogenic or non-carcinogenic risk was found for other metals. Lead isotopic ratios indicated that both Pb ore and smelting bottom ash contributed to dust Pb accumulation in SA, while coal burning, lead ore, Pb smelting bottom ash and diesel engine exhaust contributed to dust Pb accumulation in UJ. Overall, results indicated heterogenous distribution of PTM source and bioaccessibility in the vicinity of Pb smelters.

Evaluation of In Vitro Cytotoxic, Genotoxic, Apoptotic, and Cell Cycle Arrest Potential of Iron-Nickel Alloy Nanoparticles

The use of iron-nickel alloy nanoparticles (Fe-Ni ANPs) is increasing daily in various fields. People are increasingly exposed to these nanoparticles for occupational and environmental reasons. Our study determined some of the effects of Fe-Ni ANP exposure and impacts on human health at the cellular level. The cytotoxic and genotoxic potentials of Fe-Ni ANPs were investigated by XTT, clonogenic, comet, and GammaH2AX analyses using Beas-2B cells. Annexin V, multicaspase, and cell cycle arrest methods were used to understand the apoptotic mechanism of action. The intracellular ROS method was used to determine the primary mechanism that leads to cytotoxic and genotoxic activity. The Fe-Ni ANPs showed cytotoxic activity with the XTT and clonogenic methods: they had genotoxic potential, as demonstrated via genotoxicity methods. It was determined that the cytotoxic effect was realized by the caspase-dependent apoptotic pathway, and the cells were stopped at the G0/G1 stage by Fe-Ni ANPs. Increased intracellular ROS due to Fe-Ni ANPs led to cytotoxic, genotoxic, and apoptotic activity. Potential risks to human health due to Fe-Ni ANPs were then demonstrated at the cellular level.

Biomimetic synthesis of silver nanoparticles for treatment of N-Nitrosodiethylamine-induced hepatotoxicity

The development of bioengineered nanoparticles has attracted considerable universal attention in the field of medical science and disease treatment. Current studies were executed to evaluate the hepatoprotective activity of biosynthesized silver nanoparticles (AgNPs). Their characterization was performed by UV-Visible analysis, fourier transform infrared spectroscopy, transmission electron microscopy (TEM), scanning electron microscope (SEM), and Zeta analyses. In in vivo studies, albino rats (180 ± 10 g) were persuaded with model hepatic toxicant N-nitrosodiethylamine (NDEA) and subsequently cotreated with Morus multicaulis at 100 mg/kg and AgNPs at 100 µg/kg dose. NDEA administration elevates the levels of liver function test biomarkers, which were reinstated to normal by cotreatment of test drugs. The oxidative stress and concentration of drug-metabolizing enzyme increase after induction of toxicant (NDEA), these markers are restored toward normal after cotreatment of nano-drug. Treatments of M. multicaulis extract did not show such significant protection. The NDEA-treated groups showed a significant rise in the level of cytokines (interleukin [IL-6] and IL-10) and reached normal with subsequent treatment with AgNPs. Histopathological studies also exhibited the curative effect of AgNPs in the same manner. Thus current results strongly suggest that biomimetic AgNPs could be used as an effective drug against hepatic alteration.

Cell viability of novel composite hydrogels loaded with hydroxyapatite for oral and maxillofacial bone regeneration

The development of hydrogels for maxillofacial bone regeneration holds vast potential. However, some challenges need to be addressed to further their application in clinical settings. One challenge is optimizing cell viability. To improve mechanical strength, various materials have been investigated; however, incorporation of these materials within the hydrogel network may affect cell viability. The purpose of this study was to evaluate the cell viability of novel gelatin-alginate composite hydrogels loaded with hydroxyapatite (HA) and nano-hydroxyapatite (n-HA) for maxillofacial bone regeneration. Nine different hydrogels were prepared: three loaded with 0.5%, 1%, and 3% w/v HA; three loaded with 0.25%, 0.5%, and 1% w/v n-HA; one not loaded as a control and two HA and n-HA hydrogels with a lower concentration of the EDC crosslinker. Cell viability of human osteoblasts exposed to the hydrogels as affected by the HA type, size, and concentration, as well as to the crosslinker concentration, was investigated. An Alamar Blue assay was used to evaluate cell viability in the presence of hydrogel extracts and in aqueous solutions (without the hydrogel). A qualitative model was developed for explaining cell viability and growth. Higher percentages of cell viability were observed in the hydrogels loaded with hydroxyapatite as compared with the control. The effect of HA-related parameters, i.e., particle size and concentration, was found to increase the cytotoxic effect, as expressed in lower cell viability. The most favorable composites were the n-HA hydrogels. The incorporation of n-HA in the hydrogel to form a composite seems to be a very promising approach for maxillofacial bone regeneration applications.

Afatinib-loaded inhalable PLGA nanoparticles for localized therapy of non-small cell lung cancer (NSCLC)-development and in-vitro efficacy

Afatinib (AFA) is a potent aniline-quinazoline derivative, approved by the Food and Drug Administration (FDA) in 2013, as a first-line treatment for metastatic non-small cell lung cancer (NSCLC). However, its clinical application is highly limited by its poor solubility, and consequently low bioavailability. We hypothesize that loading of AFA into biodegradable PLGA nanoparticles for localized inhalational drug delivery will be instrumental in improving therapeutic outcomes in NSCLC patients. Formulated AFA nanoparticles (AFA-NP) were evaluated for physicochemical properties (particle size: 180.2 ± 15.6 nm, zeta potential: - 23.1 ± 0.2 mV, % entrapment efficiency: 34.4 ± 2.3%), formulation stability, in-vitro aerosol deposition behavior, and anticancer efficacy. Stability studies revealed the physicochemical stability of AFA-NP. Moreover, AFA-NP exhibited excellent inhalable properties (mass median aerodynamic diameter (MMAD): 4.7 ± 0.1 μm; fine particle fraction (FPF): 77.8 ± 4.3%), indicating efficient particle deposition in deep lung regions. With respect to in-vitro drug release, AFA-NP showed sustained drug release with cumulative release of 56.8 ± 6.4% after 48 h. Cytotoxic studies revealed that encapsulation of AFA into PLGA nanoparticles significantly enhanced its cytotoxic potential in KRAS-mutated NSCLC cell lines (A549, H460). Cellular uptake studies revealed enhanced internalization of coumarin-loaded nanoparticles compared to plain coumarin in A549. In addition, 3D tumor spheroid studies demonstrated superior efficacy of AFA-NP in tumor penetration and growth inhibition. To conclude, we have established in-vitro efficacy of afatinib-loaded PLGA nanoparticles as inhalable NSCLC therapy, which will be of great significance when designing preclinical and clinical studies. Graphical abstract.

The Effect of Chemical Structure of OEG Ligand Shells with Quaternary Ammonium Moiety on the Colloidal Stabilization, Cellular Uptake and Photothermal Stability of Gold Nanorods

PURPOSE

Plasmonic photothermal cancer therapy by gold nanorods (GNRs) emerges as a promising tool for cancer treatment. The goal of this study was to design cationic oligoethylene glycol (OEG) compounds varying in hydrophobicity and molecular electrostatic potential as ligand shells of GNRs. Three series of ligands with different length of OEG chain (ethylene glycol units = 3, 4, 5) and variants of quaternary ammonium salts (QAS) as terminal functional group were synthesized and compared to a prototypical quaternary ammonium ligand with alkyl chain - (16-mercaptohexadecyl)trimethylammonium bromide (MTAB).

METHODS

Step-by-step research approach starting with the preparation of compounds characterized by NMR and HRMS spectra, GNRs ligand exchange evaluation through characterization of cytotoxicity and GNRs cellular uptake was used. A method quantifying the reshaping of GNRs was applied to determine the effect of ligand structure on the heat transport from GNRs under fs-laser irradiation.

RESULTS

Fourteen out of 18 synthesized OEG compounds successfully stabilized GNRs in the water. The colloidal stability of prepared GNRs in the cell culture medium decreased with the number of OEG units. In contrast, the cellular uptake of OEG+GNRs by HeLa cells increased with the length of OEG chain while the structure of the QAS group showed a minor role. Compared to MTAB, more hydrophilic OEG compounds exhibited nearly two order of magnitude lower cytotoxicity in free state and provided efficient cellular uptake of GNRs close to the level of MTAB. Regarding photothermal properties, OEG compounds evoked the photothermal reshaping of GNRs at lower peak fluence (14.8 mJ/cm2) of femtosecond laser irradiation than the alkanethiol MTAB.

CONCLUSION

OEG+GNRs appear to be optimal for clinical applications with systemic administration of NPs not-requiring irradiation at high laser intensity such as drug delivery and photothermal therapy inducing apoptosis.

Biological and Medical Applications of Calcium Phosphate Nanoparticles

Calcium phosphate nanoparticles have a high biocompatibility and biodegradability due to their chemical similarity to human hard tissue, for example, bone and teeth. They can be used as efficient carriers for different kinds of biomolecules such as nucleic acids, proteins, peptides, antibodies, or drugs, which alone are not able to enter cells where their biological effect is required. They can be loaded with cargo molecules by incorporating them, unlike solid nanoparticles, and also by surface functionalization. This offers protection, for example, against nucleases, and the possibility for cell targeting. If such nanoparticles are functionalized with fluorescing dyes, they can be applied for imaging in vitro and in vivo. Synthesis, functionalization and cell uptake mechanisms of calcium phosphate nanoparticles are discussed together with applications in transfection, gene silencing, imaging, immunization, and bone substitution. Biodistribution data of calcium phosphate nanoparticles in vivo are reviewed.

Challenges in the Physical Characterization of Lipid Nanoparticles

Nano-sized drug transporters have become an efficient approach with considerable commercial values. Nanomedicine is not only limited to drug delivery by means of different administration routes, such as intravenous, oral, transdermal, nasal, pulmonary, and more, but also has applications in a multitude of areas, such as a vaccine, antibacterial, diagnostics and imaging, and gene delivery. This review will focus on lipid nanosystems with a wide range of applications, taking into consideration their composition, properties, and physical parameters. However, designing suitable protocol for the physical evaluation of nanoparticles is still conflicting. The main obstacle is concerning the sensitivity, reproducibility, and reliability of the adopted methodology. Some important techniques are compared and discussed in this report. Particularly, a comparison between different techniques involved in (a) the morphologic characterization, such as Cryo-TEM, SEM, and X-ray; (b) the size measurement, such as dynamic light scattering, sedimentation field flow fractionation, and optical microscopy; and (c) surface properties, namely zeta potential measurement, is described. In addition, an amperometric tool in order to investigate antioxidant activity and the response of nanomaterials towards the skin membrane has been presented.

Structural investigation, DNA interactions and in vitro anticancer studies of transition metal complexes of 3-(2-(2, 4-dihydroxy benzylidene) hydrazinyl) quinoxalin-2(1H) -one

The Schiff base ligand, 3-(2-(2, 4-dihydroxybenzylidene) hydrazinyl) quinoxalin-2(1H)-one (RHQO) has been synthesized and characterized by spectral and single crystal X-ray analysis. The Mn(II), Ni(II) and Cu(II) complexes of RHQO have been synthesized and characterized by FT-IR, UV-VIS, mass, EPR spectra, CHN, thermo gravimetric analysis, magnetic susceptibility and conductivity measurements. The morphology of the ligand and complexes is studied by Scanning Electron Microscopy. The metal complexes formed were found to be polymeric in nature. The abilities of the ligand and its metal complexes to interact and bind with calf thymus DNA (CT-DNA) has been studied by electronic absorption spectroscopy and their quantitative binding strength was evaluated in terms of their intrinsic binding constant (K_b). The cleavage interaction of the ligand and its metal complexes with super coiled pBR 322 DNA has been investigated by agarose gel electrophoresis. Cytotoxicity of the Cu(II) and Ni(II) complexes was evaluated using various cancer cell lines, Human cervical cancer cell line (Hela), B16 melanoma F10(B16-F10), Human ovarian cancer cell (SKOV3) and Breast cancer cell line (MCF7) by MTT assay. The results indicated that the ligand and its metal complexes bind with CT-DNA by groove binding mode and cleaved the supercoiled pBR 322 DNA in to nicked form. The Ni(II) and Cu(II) complexes exhibited anticancer activity without affecting the normal CHO-K1 cell lines. Communicated by Vsevolod Makeev.

Nanoparticles and their effects on differentiation of mesenchymal stem cells

Over the past decades, advancements in nanoscience and nanotechnology have resulted in numerous nanomedicine platforms. Various nanoparticles, which exhibit many unique properties, play increasingly important roles in the field of biomedicine to realize the potential of nanomedicine. Due to the capacity of self-renewal and multilineage mesenchymal differentiation, mesenchymal stem cells (MSCs) have been widely used in the area of regenerative medicine and in clinical applications due to their potential to differentiate into various lineages. There are several factors that impact the differentiation of MSCs into different lineages. Many types of biomaterials such as polymers, ceramics, and metals are commonly applied in tissue engineering and regenerative therapies, and they are continuously refined over time. In recent years, along with the rapid development of nanotechnology and nanomedicine, nanoparticles have been playing more and more important roles in the fields of biomedicine and bioengineering. The combined use of nanoparticles and MSCs in biomedicine requires greater knowledge of the effects of nanoparticles on MSCs. This review focuses on the effects of four inorganic or metallic nanoparticles (hydroxyapatite, silica, silver, and calcium carbonate), which are widely used as biomaterials, on the osteogenic and adipogenic differentiation of MSCs. In this review, the cytotoxicity of these four nanoparticles, their effects on osteogenic/adipogenic differentiation of MSCs and the signalling pathways or transcription factors involved are summarized. In addition, the chemical composition, size, shape, surface area, surface charge and surface chemistry of nanoparticles, have been reported to impact cellular behaviours. In this review, we particularly emphasize the influence of their size on cellular responses. We envision our review will provide a theoretical basis for the combined application of MSCs and nanoparticles in biomedicine.

Towards refining Raman spectroscopy-based assessment of bone composition

Various compositional parameters are derived using intensity ratios and integral area ratios of different spectral peaks and bands in the Raman spectrum of bone. The [Formula: see text]1-, [Formula: see text]2-,[Formula: see text]3-, [Formula: see text]4 PO43-, and [Formula: see text] CO32- bands represent the inorganic phase while amide I, amide III, Proline, Hydroxyproline, Phenylalanine, δ(CH3), δ(CH2), and [Formula: see text](C-H) represent the organic phase. Here, using high-resolution Raman spectroscopy, it is demonstrated that all PO43- bands of bone either partially overlap with or are positioned close to spectral contributions from the organic component. Assigned to the organic component, a shoulder at 393 cm-1 compromises accurate estimation of [Formula: see text]2 PO43- integral area, i.e., phosphate/apatite content, with implications for apatite-to-collagen and carbonate-to-phosphate ratios. Another feature at 621 cm-1 may be inaccurately interpreted as [Formula: see text]4 PO43- band broadening. In the 1020-1080 cm-1 range, the ~ 1047 cm-1 [Formula: see text]3 PO43- sub-component is obscured by the 1033 cm-1 Phenylalanine peak, while the ~ 1076 cm-1 [Formula: see text]3 PO43- sub-component is masked by the [Formula: see text]1 CO32- band. With [Formula: see text]1 PO43- peak broadening, [Formula: see text]2 PO43- integral area increases exponentially and individual peaks comprising the [Formula: see text]4 PO43- band merge together. Therefore, [Formula: see text]2 PO43- and [Formula: see text]4 PO43- band profiles are sensitive to changes in mineral crystallinity.

Aesthetic Silver-Doped Octacalcium Phosphate Powders Exhibiting Both Contact Antibacterial Ability and Low Cytotoxicity

Since the introduction of biomaterials, infection has been a serious problem in clinical operations. Although several studies have introduced hybrid materials of calcium phosphate and Ag0 nanoparticles (NPs) that exhibit antibacterial activity, released Ag+ ions and Ag0 NPs are highly cytotoxic and the materials require complex fabrication techniques such as laser irradiation. In this study, we introduce a simple one-pot synthesis method based on crystal-engineering techniques to prepare Ag+-substituted octacalcium phosphate (OCP-Ag) powder that simultaneously exhibits antibacterial activity, little change in color, and low cytotoxicity, thereby overcoming the shortcomings of calcium phosphate as a biomaterial. We used AgNO3-containing (NH4)2HPO4 aqueous solutions as reaction solutions in which Ag+ forms soluble complex [Ag(NH3)2]+ ions that are stable at Ag+ concentrations less than ∼30 mmol/L. Hydrolysis of soluble calcium phosphate in this solution led to pure OCP-Ag when the Ag+ concentration was less than ∼30 mmol/L. Crystallographic analysis showed that Ag+ substituted at the P5 PO4-conjugated sites and was uniformly distributed. When the concentration of Ag+ in the reaction solution was varied, the Ag+ content of the OCP-Ag could be controlled. The obtained OCP-Ag exhibited little color change or Ag+ release when immersed in various media; however, it exhibited contact antibacterial ability toward resident oral bacteria. The prepared OCP-Ag showed no substantial cytotoxicity toward undifferentiated and differentiated MC3T3-E1 cells in assays. Notably, when the Ag+ content in OCP-Ag was optimized (Ag: ∼1 at %), it simultaneously exhibited contact antibacterial ability, little color change, and low cytotoxicity.

The Biomolecular Corona of Lipid Nanoparticles for Gene Therapy

Gene therapy holds great potential for treating almost any disease by gene silencing, protein expression, or gene correction. To efficiently deliver the nucleic acid payload to its target tissue, the genetic material needs to be combined with a delivery platform. Lipid nanoparticles (LNPs) have proven to be excellent delivery vectors for gene therapy and are increasingly entering into routine clinical practice. Over the past two decades, the optimization of LNP formulations for nucleic acid delivery has led to a well-established body of knowledge culminating in the first-ever RNA interference therapeutic using LNP technology, i.e., Onpattro, and many more in clinical development to deliver various nucleic acid payloads. Screening a lipid library in vivo for optimal gene silencing potency in hepatocytes resulted in the identification of the Onpattro formulation. Subsequent studies discovered that the key to Onpattro's liver tropism is its ability to form a specific "biomolecular corona". In fact, apolipoprotein E (ApoE), among other proteins, adsorbed to the LNP surface enables specific hepatocyte targeting. This proof-of-principle example demonstrates the use of the biomolecular corona for targeting specific receptors and cells, thereby opening up the road to rationally designing LNPs. To date, however, only a few studies have explored in detail the corona of LNPs, and how to efficiently modulate the corona remains poorly understood. In this review, we summarize recent discoveries about the biomolecular corona, expanding the knowledge gained with other nanoparticles to LNPs for nucleic acid delivery. In particular, we address how particle stability, biodistribution, and targeting of LNPs can be influenced by the biological environment. Onpattro is used as a case study to describe both the successful development of an LNP formulation for gene therapy and the key influence of the biological environment. Moreover, we outline the techniques available to isolate and analyze the corona of LNPs, and we highlight their advantages and drawbacks. Finally, we discuss possible implications of the biomolecular corona for LNP delivery and we examine the potential of exploiting the corona as a targeting strategy beyond the liver to develop next-generation gene therapies.

Fabrication of Poly(pentaerythritol tetrakis (3-mercaptopropionate)/dipentaerythritol penta-/hexa-acrylate)HIPEs Macroporous Scaffold with Alpha Hydroxyapatite via Photopolymerization for Fibroblast Regeneration

Synthetic biomaterials that can be structured into porous scaffolds for support cell growth have played a role in developing the field of tissue engineering. This research focused on combination of biodegradable emulsion template along with the assisting of low-cost polymerization reaction. The appendage of ester-based surfactant, Hypermer B246, played a vital role which gave an outstanding dispersion in HIPEs system and degradability. PolyHIPEs were prepared by using domestic ultraviolet light source for producing a multiscale porosity material. The morphology showed a promising result of poly(pentaerythritol tetrakis (3-mercaptopropionate)/dipentaerythritol penta-/hexa-acrylate)HIPEs with varied Hypermer B246 surfactant concentration resulting in the pores size increased in between 51.2 ± 9.8 µm to 131.4 ± 26.32 µm. Cellular moieties of poly(TT/DPEHA) HIPEs were confirmed by using SEM while inclusion of hydroxyapatite were confirmed by SEM, FTIR and EDX-SEM and quantified by thermogravimetric analysis. The maximum stress and compressive modulus of the obtained materials were significantly enhanced with HA up to five percent by weight. Poly(TT/DPEHA)HIPEs with HA showed the ability for the cell attachment and the adhesion/proliferation of the cells, suggested that poly(TT/DPEHA) HIPEs with HA were suitable for biomaterial application.

Fabrication of a novel hydroxyapatite/polyether ether ketone surface nanocomposite via friction stir processing for orthopedic and dental applications

There is increasing interest in the use of polyether ether ketone (PEEK) for orthopedic and dental implant applications due to its elastic modulus (close to that of bone), biocompatibility and radiolucent properties. However, PEEK is still categorized as bioinert owing to its low integration with surrounding tissues. Methods such as depositing hydroxyapatite (HA) onto the PEEK surface could increase its bioactivity. However, depositing HA without damaging the PEEK substrate is still required further investigation. Friction stir processing is a solid-state processing method that is widely used for composite substrate fabrication. In this study, a pinless tool was used to fabricate a HA/PEEK surface nanocomposite for orthopedic and dental applications. Microscopical images of the modified substrate confirmed homogenous distribution of the HA on the surface of the PEEK. The resultant HA/PEEK surface nanocomposites demonstrated improved surface hydrophilicity coupled with better apatite formation capacity (as shown in the simulated body fluid) in comparison to the pristine PEEK, making the newly developed material more suitable for biomedical application. This surface deposition method that is carried out at low temperature would not damage the PEEK substrate and thus could be a good alternative for existing commercial methods for PEEK surface modification.

In vivo biodistribution of calcium phosphate nanoparticles after intravascular, intramuscular, intratumoral, and soft tissue administration in mice investigated by small animal PET/CT

Calcium phosphate nanoparticles were covalently surface-functionalized with the ligand DOTA and loaded with the radioisotope ⁶⁸Ga. The biodistribution of such ⁶⁸Ga-labelled nanoparticles was followed in vivo in mice by positron emission tomography in combination with computer tomography (PET-CT). The biodistribution of ⁶⁸Ga-labelled nanoparticles was compared for different application routes: intravenous, intramuscular, intratumoral, and into soft tissue. The particle distribution was measured in vivo by PET-CT after 5 min, 15 min, 30 min, 1 h, 2 h, and 4 h, and ex vivo after 5 h. After intravenous injection (tail vein), the nanoparticles rapidly entered the lungs with later redistribution into liver and spleen. The nanoparticles remained mostly at the injection site following intramuscular, intratumoral, or soft tissue application, with less than 10 percent being mobilized into the blood stream. STATEMENT OF SIGNIFICANCE: The in vivo biodistribution of DOTA-terminated calcium phosphate nanoparticles was followed by PET/CT. To our knowledge, this is the first study of this kind. Four different application routes of clinical relevance were pursued: Intravascular, intramuscular, intratumoral, and into soft tissue. Given the high importance of calcium phosphate as biomaterial and for nanoparticular drug delivery and immunization, this is most important to assess the biofate of calcium phosphate nanoparticles for therapeutic application and also judge biodistribution of nanoscopic calcium phosphate ceramics, including debris from endoprostheses and related implants.

Transformation pathways and fate of engineered nanoparticles (ENPs) in distinct interactive environmental compartments: A review

The ever increasing production and use of nano-enabled commercial products release the massive amount of engineered nanoparticles (ENPs) in the environment. An increasing number of recent studies have shown the toxic effects of ENPs on different organisms, raising concerns over the nano-pollutants behavior and fate in the various environmental compartments. After the release of ENPs in the environment, ENPs interact with various components of the environment and undergoes dynamic transformation processes. This review focus on ENPs transformations in the various environmental compartments. The transformation processes of ENPs are interrelated to multiple environmental aspects. Physical, chemical and biological processes such as the homo- or hetero-agglomeration, dissolution/sedimentation, adsorption, oxidation, reduction, sulfidation, photochemically and biologically mediated reactions mainly occur in the environment consequently changes the mobility and bioavailability of ENPs. Physico-chemical characteristics of ENPs (particle size, surface area, zeta potential/surface charge, colloidal stability, and core-shell composition) and environmental conditions (pH, ionic strength, organic and inorganic colloids, temperature, etc.) are the most important parameters which regulated the ENPs environmental transformations. Meanwhile, in the environment, organisms encountered multiple transformed ENPs rather than the pristine nanomaterials due to their interactions with various environmental materials and other pollutants. Thus it is the utmost importance to study the behavior of transformed ENPs to understand their environmental fate, bioavailability, and mode of toxicity.

Metal bioaccessibility, particle size distribution and polydispersity of playground dust in synthetic lysosomal fluids

Inhalation of playground dust-derived fine particles in schoolyards poses a risk from exposure to metal(oids) and minerals. In this work, we obtained the total concentration and bioaccessibility of metal(oids) with Gamble Solution (GS) and Artificial Lysosomal Fluid (ALF) synthetic solutions, simulating the extracellular neutral pH environment of the lung and the intracellular conditions of the macrophage, respectively. Scanning Electron Microscope (SEM), and Dynamic Light Scattering analysis (DLS) techniques were used to characterize particles with a size smaller than 2.5 μm, which can be assimilated by macrophages in the deep part of the lung. Arsenic (As), lead (Pb), copper (Cu), manganese (Mn), zinc (Zn), and iron (Fe) showed concentrations of 39.9, 147.9, 286, 1369, 2313, 112,457 mg·kg^-1, respectively. The results indicated that all studied elements were enriched when compared to (i) local geochemical background and (ii) findings reported in other cities around the world. Bioaccessibility of metal(oids) in GS was low-moderate for most studied elements. However, in ALF assays, bioaccessibility was high among the samples: for lead (Pb = 34-100%), arsenic (As = 14.7-100%), copper (Cu = 17.9-100%), and zinc (Zn = 35-52%) possibly related to hydrophobic minerals in dust. SEM and DLS image analysis showed that playground dust particles smaller than 2.5 μm are dominant, particularly particles with a size range of 500-600 nm. The polydispersity detected in these particle sizes showed that most of them might be crystalline compounds (elongated shapes) forming agglomerates instead of combustion particles (spheres). Moreover, the circularity detected varies from 0.57 to 0.79 (low roundness), which corroborates this finding. The presence of agglomerates of ultrafine/nanoparticles containing highly bioaccessible metals in playground sites may have severe implications in children's health. Therefore, further studies are required to characterize the size distribution, structure, shape and composition of such minerals which are essential factors related to the toxicology of inhaled dust particles.

Quantitative Particle Uptake by Cells as Analyzed by Different Methods

There is a large number of two-dimensional static in vitro studies about the uptake of colloidal nano- and microparticles, which has been published in the last decade. In this Minireview, different methods used for such studies are summarized and critically discussed. Supplementary experimental data allow for a direct comparison of the different techniques. Emphasis is given on how quantitative parameters can be extracted from studies in which different experimental techniques have been used, with the goal of allowing better comparison.

Isolation methods for particle protein corona complexes from protein-rich matrices

Background: Nanoparticles become rapidly encased by a protein layer when they are in contact with biological fluids. This protein shell is called a corona. The composition of the corona has a strong influence on the surface properties of the nanoparticles. It can affect their cellular interactions, uptake and signaling properties. For this reason, protein coronae are investigated frequently as an important part of particle characterization. Main body of the abstract: The protein corona can be analyzed by different methods, which have their individual advantages and challenges. The separation techniques to isolate corona-bound particles from the surrounding matrices include centrifugation, magnetism and chromatographic methods. Different organic matrices, such as blood, blood serum, plasma or different complex protein mixtures, are used and the approaches vary in parameters such as time, concentration and temperature. Depending on the investigated particle type, the choice of separation method can be crucial for the subsequent results. In addition, it is important to include suitable controls to avoid misinterpretation and false-positive or false-negative results, thus allowing the achievement of a valuable protein corona analysis result. Conclusion: Protein corona studies are an important part of particle characterization in biological matrices. This review gives a comparative overview about separation techniques, experimental parameters and challenges which occur during the investigation of the protein coronae of different particle types.

Role of nanoparticles in osteogenic differentiation of bone marrow mesenchymal stem cells

The present study aimed to investigate the osteoinductive potentiality of some selected nanostructures; Hydroxyapatite (HA-NPs), Gold (Au-NPs), Chitosan (C-NPs), Gold/hydroxyapatite (Au/HA-NPs) and Chitosan/hydroxyapatite (CH-NPs) on bone marrow- derived mesenchymal stem cells (BM-MSCs). These nanostructures were characterized using transmission electron microscope and Zetasizer. MSCs were isolated from bone marrow of rat femur bones and their identity was documented by morphology, flow cytometry and multi-potency capacity. The influence of the selected nanostructures on the viability, osteogenic differentiation and subsequent matrix mineralization of BM-MSCs was determined by MTT assay, molecular genetic analysis and alizarin red S staining, respectively. MTT analysis revealed insignificant toxicity of the tested nanostructures on BM-MSCs at concentrations ranged from 2 to 25 µg/ml over 48 h and 72 h incubation period. Notably, the tested nanostructures potentiate the osteogenic differentiation of BM-MSCs as evidenced by a prominent over-expression of runt-related transcription factor 2 (Runx-2) and bone morphogenetic protein 2 (BMP-2) genes after 7 days incubation. Moreover, the tested nanostructures induced matrix mineralization of BM-MSCs after 21 days as manifested by the formation of calcium nodules stained with alizarin red S. Conclusively, these data provide a compelling evidence for the functionality of the studied nanostructures as osteoinductive materials motivating the differentiation of BM-MSCs into osteoblasts with the most prominent effect observed with Au-NPs and Au/HA-NPs, followed by CH-NPs.

Anti-osteosarcoma effect of hydroxyapatite nanoparticles both in vitro and in vivo by downregulating the FAK/PI3K/Akt signaling pathway

Schematic representing the anti-cancer effects of nano-HAPs both in vitro and in vivo by downregulating the FAK/PI3K/Akt signaling pathway.

Novel polydatin-loaded chitosan nanoparticles for safe and efficient type 2 diabetes therapy: In silico, in vitro and in vivo approaches

Polydatin (PD) has many pharmacological activities; however, its bioavailability is still a critical cornerstone issue. The present investigation aimed to develop a novel oral formula of polydatin-loaded chitosan nanoparticles (PD-CSNPs) to improve PD therapeutic potential against type 2 diabetes. The interaction mechanism between PD and CSNPs was studied via Monte Carlo and molecular dynamics simulations. The formula was prepared and characterized by FTIR, XRD, TEM, and dynamic light scattering. The release profile of PD was studied in vitro, as well as the cytotoxicity effect versus Vero cell line and antidiabetic activity in type 2 diabetic rats were investigated. The practical results verified the formation of PD-CSNPs with entrapment efficiency of about 96.74 ± 0.39%, size average 144.25 ± 3.37 nm, and the prolonged release pattern was less than 20% after 12 hrs. The cytotoxicity study confirmed the safety of the formula at low and high doses. Moreover, the in vivo study revealed that PD-CSNPs exhibited highly significant antidiabetic efficacy in diabetic rats compared to free PD. To conclude, the current investigation proved that CSNPs are promising nanocarriers for nontoxic and effective PD delivery against type 2 diabetes.

Apoptotic and DNA-damaging effects of yttria-stabilized zirconia nanoparticles on human skin epithelial cells

Background

Yttria-stabilized zirconia (Y₂O_3/ZrO₂) nanoparticles are one of the important nanoparticles extensively used in manufacturing of plastics, textiles, catalyst, etc. Still, the cytotoxic and apoptotic effects of yttria-stabilized zirconia nanoparticles have not been well identified on human skin keratinocyte (HaCaT) cells. Therefore, in this study, we have designed to examine the cytotoxic potential of yttria-stabilized zirconia nanoparticles in HaCaT cells.

Methods

Prior to treatment, the yttria-stabilized zirconia nanoparticles were characterized by using different advanced instruments viz. dynamic light scattering (DLS), scanning electron microscope (SEM) and transmission electron microscope (TEM). Cell viability of HaCaT cells was measured by using MTS and NRU assays and viability of cells was reduced in a dose- and time-dependent manner.

Results

Reduction in the viability of cells was correlated with the rise of reactive oxygen species generation, increased caspase-3, mitochondria membrane potential and evidence of DNA strand breakage. These were consistent with the possibility that mitochondria damage can play a significant role in the cytotoxic response. Moreover, the activity of oxidative enzymes such as lipid peroxide (LPO) was increased and glutathione was reduced in HaCaT cells exposed with yttria-stabilized zirconia nanoparticles. It is also important to indicate that HaCaT cells appear to be more susceptible to yttria-stabilized zirconia nanoparticles exposure after 24 hrs.

Conclusion

This result provides a dose- and time-dependent apoptosis and genotoxicity of yttria-stabilized zirconia nanoparticles in HaCaT cells.

Impact of crystallinity and crystal size of nanostructured carbonated hydroxyapatite on pre-osteoblast in vitro biocompatibility

Nanostructured carbonated hydroxyapatite (nCHA) is a promising biomaterial for bone tissue engineering due to its chemical properties, similar to those of the bone mineral phase and its enhanced in vivo bioresorption. However, the biological effects of nCHA nanoparticles on cells and tissues are not sufficiently known. This study assessed the impact of exposing pre-osteoblasts to suspensions with high doses of nCHA nanoparticles with high or low crystallinity. MC3T3-E1 pre-osteoblasts were cultured for 1 or 7 days in a culture medium previously exposed to CHA nanoparticles for 1 day. Control groups were produced by centrifugation for removal of bigger nCHA aggregates before exposure. Interaction of nanoparticles with the culture medium drastically changed medium composition, promoting Ca, P, and protein adsorption. Transmission Electron microscopy revealed that exposed cells were able to internalize both materials, which seemed concentrated inside endosomes. No cytotoxicity was observed for both materials, regardless of centrifugation, and the exposure did not induce alterations in the release of pro-and anti-inflammatory cytokines. Morphological analysis revealed strong interactions of nCHA aggregates with cell surfaces, however without marked alterations in morphological features and cytoskeleton ultrastructure. The overall in vitro biocompatibility of nCHA materials, regardless of physicochemical characteristics such as crystallinity, encourages further studies on their clinical applications.

Synthesis and characterization of biomimetic bioceramic nanoparticles with optimized physicochemical properties for bone tissue engineering

Calcium phosphate bioceramics nanoparticles such as nano-hydroxyapatite (nHA) and nano-tricalcium phosphate (nTCP) are the main focus of basic and applied research for bone tissue regeneration. In particular, a combination of these two phases (nHA + nTCP) which refers to as "nano-biphasic calcium phosphates (nBCP)" is of interest due to the preferred biodegradation nature compared to single-phase bioceramics. However, the available synthesis processes are challenging and the biomaterials properties are yet to be optimized to mimic the physiochemical properties of the natural nanoscale bone apatite. In this study, a new approach was developed for the production of optimized bioceramic nanoparticles aiming to improve their biomimecity for better biological performances. Nanoparticles were synthesized through a carefully controlled and modified wet mechano-chemical method combined with a controlled solid-state synthesis. Different processing variables have been analyzed including; milling parameters, post-synthesis treatment, and calcination phase. Detailed physicochemical characterizations of nanoparticles revealed higher crystallinity (∼100%), lower crystallite/particle size (58 nm), higher homogeneity, reduced particle agglomeration size (6 μm), and a closer molar ratio (1.8) to biological apatite compared to control and standard samples. Furthermore, the study group was confirmed as calcium-deficient carbonate-substituted BCP nanoparticles (nHA/nβ-TCP: 92/8%). As such, the introduced method can afford an easier and accurate control over nanoparticle physiochemical properties including the composition phase which can be used for better customization of biomaterials for clinical applications. The findings of this article will also help researchers in the further advancement of production strategies of biomaterials. © 2019 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 107A: 1654-1666, 2019.

Surface Charge-Dependent Cellular Uptake of Polystyrene Nanoparticles

The evaluation of the role of physicochemical properties in the toxicity of nanoparticles is important for the understanding of toxicity mechanisms and for controlling the behavior of nanoparticles. The surface charge of nanoparticles is suggested as one of the key parameters which decide their biological impact. In this study, we synthesized fluorophore-conjugated polystyrene nanoparticles (F-PLNPs), with seven different types of surface functional groups that were all based on an identical core, to evaluate the role of surface charge in the cellular uptake of nanoparticles. Phagocytic differentiated THP-1 cells or non-phagocytic A549 cells were incubated with F-PLNP for 4 h, and their cellular uptake was quantified by fluorescence intensity and confocal microscopy. The amount of internalized F-PLNPs showed a good positive correlation with the zeta potential of F-PLNPs in both cell lines (Pearson’s r = 0.7021 and 0.7852 for zeta potential vs. cellular uptake in THP-1 cells and nonphagocytic A549 cells, respectively). This result implies that surface charge is the major parameter determining cellular uptake efficiency, although other factors such as aggregation/agglomeration, protein corona formation, and compositional elements can also influence the cellular uptake partly or indirectly.

Small molecules modified biomimetic gelatin/hydroxyapatite nanofibers constructing an ideal osteogenic microenvironment with significantly enhanced cranial bone formation

Background

Repair of nonunion critical-sized bone defects is a significant clinical challenge all over the world. Construction of osteogenic microenvironment that provides osteoconductive and osteoinductive signals is a leading strategy.

Materials and methods

In the present study, ascorbic acid (AA) and β-glycerophosphate disodium salt hydrate (β-GP) modified biomimetic gelatin/hydroxyapatite (GH) nanofibrous scaffolds were developed by electrospinning. Then the scaffolds were crosslinked by N-hydroxysulfo-succinimide sodium salt (NHS) and 1-(3-Dimethylaminopropyl)-3-ethylcarbodiimide hydrochloride (EDC). The morphology of the non-crosslinked and crosslinked scaffolds was evaluated by scanning electron microscope (SEM). Fourier transform infrared spectroscopy (FT-IR) was used to assess the interacting model between the small molecules and GH scaffold. Then MTT, Alamar Blue, and CCK8 assays were used to investigate the biocompatibility of the various crosslinked scaffolds. Subsequently, the osteogenic genes expression of bone marrow stromal cells (BMSCs) cultured on the scaffolds were detected by quantitative reverse transcription polymerase chain reaction (qRT-PCR). Finally, the crosslinked scaffolds were implanted in a rat calvarial defect model to assess the osteogenic effects in vivo.

Results

SEM results showed that the various scaffolds presented extracellular matrix (ECM)-like fibrous porous structure. (FT-IR) spectrum indicated that AA and β-GP were covalently bonded with GH scaffolds. The MTT, Alamar Blue, and CCK8 assays demonstrated that all the scaffolds can support BMSCs' growth well. The qRT-PCR results showed that the expression level of Alp and Runx2 in BMSCs on GH/A/B scaffold was about 3.5- and 1.5-fold, respectively, compared with that of GH group on day 7. The results also showed that AA- and β-GP-modified GH scaffolds can significantly induce the higher levels of osteogenic gene expression in a temporal specific manner. Importantly, AA and β-GP synergistically promoted osteoblast differentiation in vitro and dramatically induced bone regeneration in vivo. Impressively, AA and β-GP dual modified GH nanofibrous scaffold could serve as a template for guiding bone regeneration and the bone defects were almost repaired completely (94.28%±5.00%) at 6 weeks. Besides, single AA or β-GP-modified GH nanofibrous scaffolds could repair 62.95%±9.39% and 66.56%±18.45% bone defects, respectively, at 12 weeks in vivo. In addition, AA and β-GP exhibit an anti-inflammatory effect in vivo.

Conclusion

Our data highlighted that, AA, β-GP, and GH nanofibers created a fine osteoconductive and osteoinductive microenvironments for bone regeneration. We demonstrated that AA and β-GP dual modified GH nanofiber is a versatile bone tissue engineering scaffold.

Silver-doped graphene oxide nanocomposite triggers cytotoxicity and apoptosis in human hepatic normal and carcinoma cells

Introduction

Graphene oxide nanoparticles have been widely used in industry and biomedical fields due to their unique physicochemical properties. However, comparative cytotoxicity of silver-doped reduced graphene oxide (rGO–Ag) nanoparticles on normal and cancerous liver cells has not been well studied yet.

Materials and methods

This study aimed at determining the toxic potential of rGO–Ag nanocomposite on human liver normal (CHANG) and cancer (HepG2) cells. The rGO–Ag nanocomposite was characterized by using different advanced instruments, namely, dynamic light scattering, scanning electron microscope, and transmission electron microscope.

Results

The rGO–Ag nanocomposite reduced cell viability and impaired cell membrane integrity of CHANG and HepG2 cells in a dose-dependent manner. Additionally, it induced reactive oxygen species generation and reduced mitochondrial membrane potential in both cells in a dose-dependent manner. Moreover, the activity of oxidative enzymes such as lipid peroxide, superoxide dismutase, and catalase were increased and glutathione was reduced in both cells exposed to rGO–Ag nanocomposite. Pretreatment with N-acetylcysteine inhibited cytotoxicity and reactive oxygen species generation in CHANG and HepG2 cells exposed to rGO–Ag nanocomposite (50 µg/mL). DNA damage was determined by Comet assay and maximum DNA damage occurred at rGO–Ag nanocomposite (25 µg/mL) for 24 h. It is also valuable to inform that HepG2 cells appear to be slightly more susceptible to rGO–Ag nanocomposite exposure than CHANG cells.

Conclusion

This result provides a basic comparative toxic effect of rGO–Ag nanocomposite on hepatic normal and cancerous liver cells.

Review of potential health risks associated with nanoscopic calcium phosphate

Calcium phosphate is applied in many products in biomedicine, but also in toothpastes and cosmetics. In some cases, it is present in nanoparticulate form, either on purpose or after degradation or mechanical abrasion. Possible concerns are related to the biological effect of such nanoparticles. A thorough literature review shows that calcium phosphate nanoparticles as such have no inherent toxicity but can lead to an increase of the intracellular calcium concentration after endosomal uptake and lysosomal degradation. However, cells are able to clear the calcium from the cytoplasm within a few hours, unless very high doses of calcium phosphate are applied. The observed cytotoxicity in some cell culture studies, mainly for unfunctionalized particles, is probably due to particle agglomeration and subsequent sedimentation onto the cell layer, leading to a very high local particle concentration, a high particle uptake, and subsequent cell death. There is no risk from an oral uptake of calcium phosphate nanoparticles due to their rapid dissolution in the stomach. The risk from dermal or mucosal uptake is very low. Calcium phosphate nanoparticles can enter the bloodstream by inhalation, but no adverse effects have been observed, except for a prolonged exposition to high particle doses. Calcium phosphate nanoparticles inside the body (e.g. after implantation or due to abrasion) do not pose a risk as they are typically resorbed and dissolved by osteoclasts and macrophages. There is no indication for a significant influence of the calcium phosphate phase or the particle shape (e.g. spherical or rod-like) on the biological response. In summary, the risk associated with an exposition to nanoparticulate calcium phosphate in doses that are usually applied in biomedicine, health care products, and cosmetics is very low and most likely not present at all.

STATEMENT OF SIGNIFICANCE

Calcium phosphate is a well-established biomaterial. However, there are occasions when it occurs in a nanoparticulate form (e.g. as nanoparticle or as nanoparticulate bone substitution material) or after abrasion from a calcium phosphate-coated metal implant. In the light of the current discussion on the safety of nanoparticles, there have been concerns about potential adverse effects of nano-calcium phosphate, e.g. in a statement of a EU study group from 2016 about possible dangers associated with non-spherical nano-hydroxyapatite in cosmetics. In the US, there was a discussion in 2016 about the dangers of nano-calcium phosphate in babyfood. In this review, the potential exposition routes for nano-calcium phosphate are reviewed, with special emphasis on its application as biomaterial.

Dynamic Light Scattering of Biopharmaceutics-Can Analytical Performance Be Enhanced by Laser Power?

Background: Dynamic light scattering (DLS) is an important tool to characterize colloidal systems and adequate sizing is particularly critical in the field of protein formulations. Among the different factors that can influence the measurement result, the effect of laser power has so far not been studied thoroughly. Methods: The sensitivity of a DLS instrument was first considered on a theoretical level, followed by experiments using DLS instruments, equipped with two different lasers of (nominal) 45 mW, and 100 mW, respectively. This work analyzes dilute colloidal dispersions of lysozyme as model protein. Results: Theoretical findings agreed with experiments in that only enhanced laser power of 100 mW laser allowed measuring a 0.1 mg/mL protein dispersion in a reliable manner. Results confirmed the usefulness of the presented theoretical considerations in improving a general understanding of the limiting factors in DLS. Conclusions: Laser power is a critical aspect regarding adequate colloidal analysis by DLS. Practical guidance is provided to help scientists specifically with measuring dilute samples to choose both an optimal instrument configuration as well as a robust experimental procedure.

Incineration of Nanoclay Composites Leads to Byproducts with Reduced Cellular Reactivity

Addition of nanoclays into a polymer matrix leads to nanocomposites with enhanced properties to be used in plastics for food packaging applications. Because of the plastics' high stored energy value, such nanocomposites make good candidates for disposal via municipal solid waste plants. However, upon disposal, increased concerns related to nanocomposites' byproducts potential toxicity arise, especially considering that such byproducts could escape disposal filters to cause inhalation hazards. Herein, we investigated the effects that byproducts of a polymer polylactic acid-based nanocomposite containing a functionalized montmorillonite nanoclay (Cloisite 30B) could pose to human lung epithelial cells, used as a model for inhalation exposure. Analysis showed that the byproducts induced toxic responses, including reductions in cellular viability, changes in cellular morphology, and cytoskeletal alterations, however only at high doses of exposure. The degree of dispersion of nanoclays in the polymer matrix appeared to influence the material characteristics, degradation, and ultimately toxicity. With toxicity of the byproduct occurring at high doses, safety protocols should be considered, along with deleterious effects investigations to thus help aid in safer, yet still effective products and disposal strategies.

In Vitro Uptake of Hydroxyapatite Nanoparticles and Their Effect on Osteogenic Differentiation of Human Mesenchymal Stem Cells

There have been many applications in biomedical fields based on hydroxyapatite nanoparticles (HA NPs) over the past decades. However, the biocompatibility of HANPs is affected by exposure dose, particle size, and the way of contact with cells. The objective of this study is to investigate the effect of HA NPs with different sizes on osteogenesis using human mesenchymal stem cells (hMSCs). Three different-sized HA NPs (~50, ~100, and ~150 nm, resp.) were synthesized to study the cytotoxicity, cellular uptake, and effect on osteogenic differentiation of hMSCs. The results clearly showed that each size of HA NPs had dose-dependent cytotoxicity on hMSCs. It was found that HA NPs could be uptaken into hMSCs. The osteogenic differentiation of hMSCs was evaluated through alkaline phosphatase (ALP) activity measurement, ALP staining, immunofluorescent staining for osteopontin (OPN), and real-time polymerase chain reaction (RT-PCR) examination. As expected, HA NPs of all sizes could promote the differentiation of hMSCs towards osteoblast lineage. Among the three sizes, smaller-sized HA NPs (~50 and ~100 nm) appeared to be more effective in stimulating osteogenic differentiation of hMSCs.

Synthesis and evaluation of layered double hydroxide/doxycycline and cobalt ferrite/chitosan nanohybrid efficacy on gram positive and gram negative bacteria

The current study tested the antibacterial activity of layered double hydroxide (LDH), LDH-Doxycycline nanohybrid, Cobalt ferrite nanoparticles (NPs) and Cobalt ferrite-Chitosan nanohybrid against Gram-negative bacteria Escherichia coli. In addition, the study investigated the Cobalt ferrite NPs and Cobalt ferrite-Chitosan nanohybrids against Gram-positive bacteria Staphylococcus aureus. The nanoparticles and nanohybrids were synthesized by a chemical method and characterized by high resolution transmission electron microscope (HRTEM), X-ray diffraction (XRD), and Fourier transformation Infra-red Spectroscopy (FTIR). Multi-point Brunauer-Emmet-Teller (BET) method determined the specific surface area while Barrett-Joyner-Halenda for (BJH) figured the corresponding specific pore volume and pore size and Zetasizer ranked the particle size distribution. Minimum inhibitory concentration (MIC) and the minimum bactericidal concentration (MBC) measurements besides agar well diffusion method showed the antimicrobial activity of the nanoparticles. The results revealed no antibacterial activity of the LDH and Cobalt ferrite NPs alone. Meanwhile, the Cobalt ferrite-Chitosan nanohybrid and LDH-Doxycycline showed a high activity antibacterial effect.