Understanding changes in cellulose crystalline structure of lignocellulosic biomass during ionic liquid pretreatment by XRD

Adsorption properties of cellulose-derived hydrogel and magnetic hydrogels from Sophora flavescens on Cu2+ and Congo red

This study synthesized a robust, magnetically responsive hydrogel from Sophora flavescens-modified cellulose and chitosan, employing Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA and DTG), and scanning electron microscopy (SEM) to confirm the preservation of cellulose's intrinsic properties and the hydrogel's remarkable elasticity, toughness, and porosity. These hydrogels integrate cellulose's structural backbone with functional moieties from chitosan, enhancing adsorption capabilities for Cu2+ ions and Congo red (CR) dye. Kinetic and thermodynamic analyses reveal that adsorption is spontaneous and endothermic, following a pseudo-second-order model and the Freundlich isotherm. Notably, Cu2+ adsorption capacity increases with pH, while CR adsorption initially decreases before rising, demonstrating the hydrogels' potential as effective, sustainable adsorbents for removing pollutants from water.

Ionic liquid-assisted pretreatment of lignocellulosic biomass using purified Streptomyces MS2A cellulase for bioethanol production

In recent years, the process of producing bioethanol from lignocellulosic biomass through biorefining has become increasingly important. However, to obtain a high yield of ethanol, the complex structures in the feedstock must be broken down into simple sugars. A cost-effective and innovative method for achieving this is ionic liquid pre-treatment, which is widely used to efficiently hydrolyze the lignocellulosic material. The study aims to produce a significant profusion of bioethanol via catalytic hydrolysis of ionic liquid-treated lignocellulose biomass. The current study reports the purification of Streptomyces sp. MS2A cellulase via ultrafiltration and gel permeation chromatography. The kinetic parameters and the biochemical nature of the purified cellulase were analyzed for the effective breakdown of the EMIM[OAC] treated lignocellulose chain. The two-step cellulase purification resulted in 6.28 and 12.44 purification folds. The purified cellulase shows a Km value of 0.82 ± 0.21 mM, and a Vmax value of 85.59 ± 8.87 μmol min-1 mg-1 with the catalytic efficiency of 1.027 S-1. The thermodynamic parameters like ΔH, ΔS, and ΔG of the system were studied along with the thermal deactivation kinetics of cellulase. The optimal temperature and pH of the purified cellulase enzyme for hydrolysis was found to be 40 °C and 7. The rice husk and wheat husk used in this study were pretreated with the EMIM [OAC] ionic liquid and the change in the structure of lignocellulosic biomass was observed via HRSEM. The ionic liquid treated biomass showed the highest catalytic hydrolysis yield of 106.66 ± 0.19 mol/ml on the third day. The obtained glucose was fermented with Saccharomyces cerevisiae to yield 23.43 g of ethanol/l of glucose from the rice husk (RH) and 24.28 g of ethanol/l of glucose from the wheat husk (WH).

Isolation and characterization of microcrystalline cellulose from an agro-waste tamarind (Tamarindus indica) seeds and its suitability investigation for biofilm formulation

The exploration of potential bio-fillers for bio-film application is a promising approach to ensure biodegradable, eco-friendly, good-quality materials with high-performance applications. This is a comprehensive study executed to establish the utility of an agro-waste Tamarindus indica seeds for microcrystalline cellulose production and to assess its feasibility for biofilm fabrication. The extraction was carried out through consecutive chemical-mediated alkalization, acid hydrolysis and bleaching. The isolated microcrystalline cellulose from Tamarindus indica seeds (TSMCC) was characterized through chemical, thermal and morphological characterization to validate the cellulose contribution, thermal resistance, and compatibility of the material. The physical parameters as density and yield percentage were assessed to evaluate its light-weight utility and economic productivity. These examinations revealed that TSMCC has good specific properties such as high cellulose content (90.57 %), average density (1.561 g/cm3), feasible average roughness (12.161 nm), desired particle size (60.40 ± 21.10 μm), good crystallinity (CI-77.6 %) and thermal stability (up to 230 °C); which are worthwhile to consider TSMCC for bio-film formulation. Subsequently, bio-films were formulated by reinforcing TSMCC in polylactic acid (PLA) matrix and the mechanical properties of the bio-films were then studied to establish the efficacy of TSMCC. It is revealed that the properties of pure PLA film increased after being incorporated with TSMCC, where 5 %TSMCC addition showed greater impact on crystalline index (26.16 % to 39.62 %), thermal stability (333oc to 389 °C), tensile strength (36.11 ± 2.90 MPa to 40.22 ± 3.22 MPa) and modulus (2.62 ± 0.55GPa to 4.15 ± 0.53GPa). In light of all promising features, 5 % TSMCC is recommended as a potential filler reinforcement for the groundwork of good quality bio-films for active packaging applications in future.

Layer-by-layer assembly induced strong, hydrophobic and anti-bacterial TEMPO oxidized cellulose nanofibrils films for highly efficient UV-shielding and oil-water separation

Anti-ultraviolet material with cost-effectiveness, environmental friendliness, and multifunction is urgently needed to address the serious problem of ultraviolet radiation. However, traditional anti-ultraviolet products based on plastics are unsustainable and harmful to the environment. Herein, the cellulose films with a sandwich structure using a surface assembly technique were reported. Natural L-phenylalanine was grafted onto cellulose nanofibrils via amidation to enhance their UV-shielding property. To address the hydrophilic nature and limited mechanical strength of cellulose films, we employed octadecyltrichlorosilane and 4ARM-PEG-NH2 for hydrophobic coating and mechanical reinforcement, respectively. In addition to providing complete UV resistance in the wavelength range of 200-320 nm, sample OPT5 exhibited significantly improved tensile stress, Young's modulus, and toughness, measuring 174.09 MPa, 71.11 MPa, and 295.33 MJ/m3, respectively. Furthermore, due to the presence of antibacterial amine groups, the modified film demonstrated a satisfactory inhibitory effect on the growth of Escherichia coli and Bacillus subtilis. Compared to natural cellulose films, the hydrophobically modified material achieved a contact angle of up to 121.1°, which enabled efficient separation of oil-water mixtures with a maximum separation efficiency of 93.87 %. In summary, the proposed TOCNF-based UV-shielding film with multifunctionality holds great potential for replacing petrochemical-derived plastics and serving as an applicable and sustainable membrane material.

Physicochemical, thermal, pasting, morphological, functional and bioactive binding characteristics of starches of different oat varieties of North-Western Himalayas

Starches were isolated from five oat varieties (SFO-1, SFO-3, Sabzar, SKO-20 and SKO-96) grown in North-Western Himalayas of India. Moisture content of the varieties ranged from 9.25 ± 0.09 to 13.21 ± 0.11 %, indicating their shelf-stability. Results suggested >90 % purity of starches as was evident from values of ash, proteins, and lipids. Amylose content results showed that all starches fall within category of intermediate-amylose starches. Lambdamax, blue value and OD620/550 were found significantly (p ≤ 0.05) higher in SKO-20. Sabzar exhibited higher starch hydrolysis percentage of 85.16 % whereas, lowest was observed in SKO-20 (78.12 %). Degree of syneresis was higher in SKO-20 however, its freeze-thaw stability was lesser. Wide peak in FTIR spectra at 3320 cm-1 confirms nature of starches. SKO-20 exhibited significantly higher onset gelatinization temperature (65.19 ± 1.06 °C) and enthalpy (15.78 ± 0.15 J/g) whereas, Sabzar exhibited lowest enthalpy. Pasting characteristics indicated lowest and highest final viscosity in SKO-20 (341.30 ± 2.11 mPas) and SKO-96 (1470 ± 4.56 mPas), respectively. SEM results indicated irregular and polygonal shape of starches with size <10 μm. SKO-20 exhibited lowest disintegration time of 2.08 ± 0.01 min and Sabzar showed highest (3.31 ± 0.07 min). SKO-20 released more curcumin (71.28 %) whereas, Sabzar released less. This suggests that SKO-20 could be used as better excipient for delivery of curcumin at target site.

Green Energy Storage: Chitosan-Avocado Starch Hydrogels for a Novel Generation of Zinc Battery Electrolytes

Meeting the ever-increasing global energy demands through sustainable and environmentally friendly means is a paramount challenge. In response to this imperative, this study is dedicated to the development of biopolymer electrolytes, which hold promise for improving the efficiency, safety, and biodegradability of energy systems. The present study aims to evaluate hydrogels synthesized from chitosan biopolymer and starch from avocado seed residues in different ratios, and dried using freeze-thawing and freeze-drying techniques. Epichlorohydrin was used as a chemical crosslinker to create a suitable degree of swelling using an ionic solution. Physical freezing crosslinking strategies such as freezing-thawing and freezing-drying were performed to generate a denser porous structure in the polymer matrix. Subsequently, synthesized electrolytes were immersed in 12 M KOH solution to improve their electrochemical properties. The effect of the different ratios of starch in the hydrogels on the structural properties of the materials was evaluated using characterization techniques such as FTIR and XRD, which allowed to confirm the crosslinking between chitosan and starch. The electrochemical performance of the hydrogels is assessed using electrochemical impedance spectroscopy. A maximum conductivity value of 0.61 S·cm-1 was achieved at room temperature. The designed materials were tested in prototype zinc-air batteries; their specific capacity value was 1618 mA h·g-1, and their obtained power density was 90 mW·cm-2. These substantial findings unequivocally underscore the potential of the synthesized hydrogels as highly promising electrolytes for the application in zinc-air battery systems.

Eucalyptus bleached kraft pulp-ionic liquid inks for 3D printing of ionogels and hydrogels

3D printing has been recently recognized as one of the most promising technologies due to the multiple options to fabricate cost-effective and customizable objects. However, the necessity to substitute fossil fuels as raw materials is increasing the research on bio-based inks with recyclable and eco-friendly properties. In this work, we formulated inks for the 3D printing of ionogels and hydrogels with bleached kraft pulp dissolved in [Emim][DMP] at different concentrations (1-4 wt%). We explored each ink's rheological properties and printability and compared the printability parameters with a commercial ink. The rheological results showed that the 3 % and 4 % cellulose-ionic liquid inks exhibited the best properties. Both had values of damping factor between 0.4 and 0.7 and values of yield stress between 1900 and 2500 Pa. Analyzing the printability, the 4 wt% ink was selected as the most promising because the printed ionogels and the hydrogels had the best print resolution and fidelity, similar to the reference ink. After printing, ionogels and hydrogels had values of the elastic modulus (G') between 10³ and 10⁴ Pa, and the ionogels are recyclables. Altogether, these 3D printed cellulose ionogels and hydrogels may have an opportunity in the electrochemical and medical fields, respectively.

Capillary-Assisted Monitoring of Milk Freshness via a Porous Cellulose-Based Label with High pH Sensitivity

A cellulose-based matrix for monitoring milk freshness (MF) was produced from rice straw particles (RSPs) in a 0.125-0.150 mm that was bis-quaternized to attach bromocresol purple (BP) as a sensor. Under alkali conditions, the obstinate structure of the rice straw had opened, thereby improving the accessibility of the cellulose. Bis-quaternization created more adsorption sites for BP. The maximum adsorption capacity was 97.68 mg/g. The sensors were interwoven with cellulosic fibers to form the cellulose-based label with a relatively loose three-dimensional structure via hydrogen bonds. As the proportion of BP-BCRPs was increased from 10% to 40%, the air permeability of the label increased from 3.76 to 15.01 mm/s, which increased the response to the tested gases (10.12 s for 1 mL of acetic acid). The intelligent label exhibited excellent sensitivity at pH values of 3-9 with highly saturated color changes. During the storage period, the label color shifted from blue-purple to yellow as acidity was increased from 17.24 to 19.8 °T due to capillarity action, providing a timely warning to consumers. The prepared colorimetric porous intelligent cellulose-based label is suitable for monitoring of MF.

Mechanisms of ZnO Nanoparticles Enhancing Phototransformation of Biologically Derived Organic Phosphorus in Aquatic Environments

Zinc oxide nanoparticles (ZnO NPs), as the highly efficient photocatalysts, could enhance the transformation of biogenic organic phosphorus (OP) to orthophosphate (PO₄^3-) by photodegradation, accelerating eutrophication. Conversely, orthophosphate can also transform ZnO NPs and thus potentially alter their catalytic and chemical properties. Here, we investigated the transformation mechanisms of three biogenic OP compounds and ZnO NPs under ultraviolet light (UV) illumination: inositol phosphates (IHPs), nucleic acids (DNA), and aminoethylphosphonic acid (AEP). The physicochemical characteristics of the resulting products were systematically characterized. Results show that ZnO NPs accelerated the transformation of IHPs, DNA, and AEP to inorganic phosphorus with the direct photolysis efficiencies of 98.14, 87.68, and 51.76%, respectively. The main component of the precipitates remained ZnO NPs, and Zn₃(PO₄)₂ was identified. Zinc phytate was determined in the ZnO NP-IHP system. ³¹P NMR and FTIR further confirmed that the aquatic phase contained orthophosphate. Photoproduced hydroxyl (·OH) and superoxide (·O₂^-) were proved to play a dominant role in the OP photomineralization. Furthermore, ZnO NPs significantly enhanced the intensity of ·OH and ·O₂^- compared to the OP and Zn²⁺ solution alone. This work explored the light-induced mineralization processes of OP with ZnO NPs indicating that nanophotocatalysts may play a positive role in transformation of OP species in aquatic environments to further contribute to eutrophication.

Fabrication and characterization of a novel Ba2+-loaded sawdust biochar doped with iron oxide for the super-adsorption of SO42- from wastewater

Biochar is a low-cost adsorbent used in the treatment of contaminated wastewater. We investigated the potential of an Fe-impregnated, Ba²⁺-loaded biochar (Fe-(Ba-BC)) for the removal of SO₄^2- from aqueous solutions. The Ba²⁺-loaded biochar was synthesized from sawdust impregnated with iron oxide via pyrolysis at 600 °C. The porous structure of the Fe-(Ba-BC) was identified by scanning electron microscopy before sulfate was adsorbed onto the adsorbent. Functional groups were determined by energy-dispersive spectrophotometry and Raman spectrometry.. The Fe-(Ba-BC) Raman peaks before the experiment were higher than after, suggesting the precipitation of BaSO₄. The presence of BaCl₂ on the surface of the biochar was confirmed by X-ray diffraction. Batch sorption results showed that Fe-(Ba-BC) strongly adsorbed aqueous SO₄^2- with a removal efficacy of 96.7% under the optimum conditions of 0.25 M BaCl₂, a contact time of 480 min, a pH of 9 and an adsorbent dose of 2 g. The optimum condition for removal and reaction rate kinetics analysis indicated that adsorption curve fitted well with PSO, k₂ 0.00015 confirmed the removal of SO₄^2- via chemisorption. Thus, Fe-(Ba-BC) was found to be a favorable adsorbent for removing SO₄^2-.

Structural Evolution of Cellulose from Bamboo Fibers and Parenchyma Cells during Ionic Liquid Pretreatment for Enhanced Hydrolysis

Bamboo fibers and parenchyma cells, the two dominant types of cells in bamboo, exhibit some interesting differences in cellulose crystalline structures. In the present investigation, we further demonstrated that these structural differences affect their response during ionic liquid (IL) pretreatment and the sugar conversion yield, by tracking their changes in morphology, chemical, and crystalline structures. All of the results pointed to the fact that the cellulose from bamboo fibers exhibited higher recalcitrance to IL pretreatment, with a significantly lower change in crystallinity index, d spacings from the (110) and (11̅0) planes, crystallite sizes, and easier transformation from cellulose I to cellulose II after pretreatment, as compared to that from parenchyma cells. Furthermore, the crystalline parameters of (110) and (11̅0) lattice planes exhibited more changes compared to the (200) direction. This investigation highlights the significance of parenchyma cell wastes from bamboo processing plants as a competitive candidate for the biorefinery industry.

Enhancing the interaction between cellulose and dilute aqueous ionic liquid solutions and its implication to ionic liquid recycling and reuse

Cellulose-dissolving ionic liquids (ILs) have been used in biomass pretreatment for over a decade. Cellulose solubility in the ILs is strongly inhibited by water, which has negative impacts on IL pretreatment and reuse of the recycled ILs. Here, a distillation and aeration apparatus was used as the reactor for biomass pretreatment in dilute aqueous IL solutions and in recycled IL liquor without drying or purification. Four biomass types, switchgrass, miscanthus, sorghum and pine, were studied. X-ray diffraction (XRD) was used to measure the interaction between biomass and the IL. Small angle neutron scattering (SANS) was applied to monitor the changes of the pore structure in wet biomass samples. Satisfactory enzymatic hydrolysis results were obtained among all the pretreated samples.

Intensification of alkaline delignification of sugarcane bagasse using ultrasound assisted approach

Ultrasound-assisted approach has been investigated for delignification so as to develop green and sustainable technology. Combination of NaOH with ultrasound has been applied with detailed study into effect of various parameters such as time (operating range of 15-90 min), alkali concentration (0.25 M-2.5 M), solvent loading (1:15-1:30 w/v), temperature (50-90 ˚C), power (40-140 W) and duty cycle (40-70 %) at fixed frequency of 20 kHz. The optimized operating conditions established for the ultrasonic horn were 1 M as the NaOH concentration, 1 h as treatment time, 70˚C as the operating temperature, 1:20 as the biomass loading ratio, 100 W as the ultrasonic power and 70% duty cycle yielding 67.30% as the delignification extent. Comparative study performed using conventional and ultrasonic bath assisted alkaline treatment revealed lower delignification as 48.09% and 61.55% respectively. The biomass samples were characterized by SEM, XRD, FTIR and BET techniques to establish the role of ultrasound during the treatment. The morphological changes based on the ultrasound treatment demonstrated by SEM were favorable for enhanced delignification and also the crystallinity index was more in the case of ultrasound treated material than that obtained by conventional method. Specific surface area and pore size determinations based on BET analysis also confirmed beneficial role of ultrasound. The overall results clearly demonstrated the intensification obtained due to the use of ultrasonic reactors.

High efficiency and clean separation of eucalyptus components by glycolic acid pretreatment

Glycolic acid has chemical properties similar to those of formic acid. Therefore, similar to formic acid pretreatment, glycolic acid pretreatment has the separation effect of hemicellulose. In this study, eucalyptus hemicellulose was effectively separated by glycolic acid pretreatment. The effects of glycolic acid concentration, temperature and time on the separation of cellulose, hemicellulose and lignin were investigated. The optimum conditions were acid concentration 5.40%, temperature 140 °C, time 3.0 h. The highest yield of xylose was 56.72%. The recovery rate of glycolic acid was 91%. Compared to formic acid, the yield of xylose increased to 10.33% while that of lignin decreased to 11.08%. It showed high selectivity for hemicellulose separation, yielding 65.48% hemicellulose with 72.08% purity. The depolymerization and repolymerization of lignin were inhibited. The integrity of the cellulose structure was preserved. It provides theoretical support for the fractional separation and high-value transformation of lignocellulosic biomass.

Carnauba (Copernicia prunifera) palm tree biomass as adsorbent for Pb(II) and Cd(II) from water medium

Plant-based biomass (CFB (carnauba fruit biomass)) obtained from the fruit exocarp of the species Copernicia prunifera (Mill.) H.E. Moore (carnauba) was evaluated for its viability as an adsorbent of potentially toxic metals in aqueous medium. The CFB was characterized by powder X-ray spectroscopy (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and zeta potential to investigate the morphology of the biosorbent and its interaction with water soluble metal ions of Pb and Cd. The biomass presents an amorphous structure, with negative zeta potential (- 2.59 mV), and the presence of functional groups such as O-H, C-O-C, C-H, and C=O. The removal potential of Pb(II) and Cd(II) was performed in a batch system, and monoelement solutions were tested to assess the effects of adsorbent dose and initial metal ion concentration, pH at the point of zero charge (pH_PZC), sorption kinetics, and adsorption capacity. The most appropriate adsorbent concentration was 5 g/L, and sorption studies were carried out at pH 5.0 (pH_PZC = 4.68), in which the surface of the adsorbent shows negative charges and favors the adsorption of metal ions. Kinetic studies showed that the pseudo-second order model best fit the experimental data, and equilibrium was reached at 120 min of contact time. The experimental sorption capacity (SC_exp) for Pb and Cd was around 28 and 34 mg/g, respectively, and six different non-linear isotherm models were used to describe the sorption phenomena, among them, four with 2 parameters, i.e., Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich (DR), respectively, and two with 3 parameters, namely, SIPS and Hill. The non-linear Temkin and Freundlich isotherm models best fit the experimental data for Pb(II) and Cd(II), respectively. According to the Langmuir model, Q_max was 26 mg/g and 58 mg/g for Pb(II) and Cd(II), respectively, indicating the efficiency of CFB as a new alternative to conventional methods for the removal of potentially toxic metals from aqueous medium.

Experimental determination of the effects of pretreatment on selected Nigerian lignocellulosic biomass in bioethanol production

In the present study, five lignocellulosic biomass namely, corn cobs (Zea mays), rice husks (Oryza sativa), cassava peels (Manihot esculenta), sugar cane bagasse (Saccharum officinarum), and white yam peels (Dioscorea rotundata) of two mesh sizes of 300 and 425 microns and a combination of some and all of the biomass were pretreated using combined hydrothermal and acid-based, combined hydrothermal and alkali-based and hydrothermal only processes. The raw and pretreated biomass were also characterized by Fourier transform infrared spectroscopy (FT-IR), Brunauer-Emmett-Teller (BET), X-Ray diffraction (XRD), and Scanning electron microscopy (SEM) to determine the effects of the various pretreatments on the biomass being studied. The cellulose values of the raw biomass range from 25.8 wt% for cassava peels biomass to 40.0 wt% for sugar cane bagasse. The values of the cellulose content increased slightly with the pretreatment, ranging from 33.2 to 43.8 wt%. The results of the analysis indicate that the hydrothermal and alkaline-based pretreatment shows more severity on the different biomass being studied as seen from the pore characteristics results of corn cobs + rice husks biomass, which also shows that the combination of feedstocks can effectively improve the properties of the biomass in the bioethanol production process. The FTIR analysis also showed that the crystalline cellulose present in all the biomass was converted to the amorphous form after the pretreatment processes. The pore characteristics for mixed corn cobs and rice husks biomass have the highest specific surface area and pore volume of 1837 m2/g and 0.5570 cc/g respectively.

Optimization of process parameters for bio-enzymatic and enzymatic saccharification of waste broken rice for ethanol production using response surface methodology and artificial neural network-genetic algorithm

Reducible sugar solution has been produced from waste broken rice by a novel saccharification process using a combination of bio-enzyme (bakhar) and commercial enzyme (α-amylase). The reducible sugar solution thus produced is a promising raw material for the production of bioethanol using the fermentation process. Response surface methodology (RSM) and Artificial neural network-genetic algorithm (ANN-GA) have been used separately to optimize the multivariable process parameters for maximum yield of the total reducing sugar (TRS) in saccharification process. The maximum yield (0.704 g/g) of TRS is predicted by the ANN-GA model at a temperature of 93 °C, saccharification time of 250 min, 6.5 pH and 1.25 mL/kg of enzyme dosages, while the RSM predicts the maximum yield of 0.7025 g/g at a little different process conditions. The fresh experimental validation of the said model predictions by ANN-GA and RSM is found to be satisfactory with the relative mean error of 2.4% and 3.8% and coefficients of determination of 0.997 and 0.996.

Insight into the effect of lignocellulosic biomass source on the performance of biochar as persulfate activator for aqueous organic pollutants remediation: Epicarp and mesocarp of citrus peels as examples

In this work, the cellulose-enriched mesocarp of tangerine peels (TP) and the lignin-enriched epicarp of the peels (e-TPs) were used as examples to unveil the link between the basic components (cellulose, hemicellulose and lignin) in lignocellulosic biomass and catalytic activity of biochar towards peroxymonosulfate (PMS) activation. The TP biochar exhibits sheet-like morphology and high porosity, while the e-TPs biochar shows a bulk morphology. Accordingly, the former outperformed the latter in terms of catalytic degradation of phenol with PMS, attributing to the higher content of cellulose than lignin in the TP precursor, which was further supported by comparing the catalytic activity of biochar prepared from binary mixtures containing different proportions of cellulose and lignin. Nonradical oxidation pathway based on singlet oxygen (¹O₂) and electron-transfer mechanism was involved in the TP biochar/PMS system and the key role of CO group in biochar for ¹O₂ generation was computationally demonstrated. Additionally, the unique porous structure and surface chemistry of TP biochar endows it an excellent adsorbent for various organic pollutants. Herein, this work provides an insight into the effect of lignocellulosic biomass source on the catalytic property of biochar, which would be beneficial to screen lignocellulosic biowastes to prepare high-performance biochar for water remediation.

From paper mill waste to single cell oil: Enzymatic hydrolysis to sugars and their fermentation into microbial oil by the yeast Lipomyces starkeyi

Single cell oil (SCO) represents an outstanding alternative to both fossil sources and vegetable oils from food crops waste. In this work, an innovative two-step process for the conversion of cellulosic paper mill waste into SCO was proposed and optimised. Hydrolysates containing glucose and xylose were produced by enzymatic hydrolysis of the untreated waste. Under the optimised reaction conditions (Cellic® CTec2 25 FPU/g glucan, 48 h, biomass loading 20 g/L), glucose and xylose yields of 95 mol% were reached. The undetoxified hydrolysate was adopted as substrate for a batch-mode fermentation by the oleaginous yeast Lipomyces starkeyi. Lipid yield, content for single cell, production and maximum oil productivity were 20.2 wt%, 37 wt%, 3.7 g/L and 2.0 g/L/d respectively. This new generation oil, obtained from a negative value industrial waste, represents a promising platform chemical for the production of biodiesel, biosurfactants, animal feed and biobased plastics.

Optimisation of glucose and levulinic acid production from the cellulose fraction of giant reed (Arundo donax L.) performed in the presence of ferric chloride under microwave heating

A two-step exploitation of the giant reed cellulose to glucose and levulinic acid, after the complete removal of the hemicellulose fraction, was investigated using FeCl₃ as catalyst. In the first step, the microwave-assisted hydrolysis of cellulose to glucose was optimised by response surface methodology analysis, considering the effect of temperature, reaction time and catalyst amount. Under the optimised reaction conditions, the glucose yield was 39.9 mol%. The cellulose-rich residue was also converted by enzymatic hydrolysis, achieving the glucose yield of 39.8 mol%. The exhausted residue deriving from the chemical hydrolysis was further converted to levulinic acid by microwave treatment at harsher reaction conditions. The maximum levulinic acid yield was 64.3 mol%. On the whole, this cascade approach ensured an extensive and sustainable exploitation of the C6 carbohydrates to glucose and levulinic acid, corresponding to about 70 mol% of glucan converted to these valuable bioproducts in the two steps.

Enhanced fuel characteristics and physical chemistry of microwave hydrochar for sustainable fuel pellet production via co-densification

Microwave assisted hydrothermal treatment (MHTC) was compared with torrefaction in terms of carbonization efficiency and physicochemical characteristics of char products. The utilization of produced char was optimized for composite solid biofuel production. The results show that MHTC significantly improved the binding capability of the microwave hydrochar (MHC) particles during co-densification with unprocessed biomass and coal. One possible contributor to the improved binding is the pseudo lignin formed during the MHTC, which led to a better interlocking of the feedstock particles and promoted the solid bridge formation. Composite pellet prepared with 80 wt% of torrefaction char (TC-120), 10 wt% of microwave hydrochar (MHC-30), and 10 wt% of Coal-04 showed a higher heating value of 24.54 MJ/kg and energy density of 26.43 GJ/m³, which is significantly higher than that of the raw cotton stalk pellet (16.77 MJ/kg and 18.76 GJ/m³, respectively), showing great promise as a solid biofuel. The moisture resistance and oxidation reactivity are also significantly improved. The results demonstrate that MHCs provides dual functionalities in acting as binder and fuel promoter in the production of composite biofuel. This study can provide new insight into the unique functions of MHC during fuel application, which demonstrates the great potential of applying MHTC in energy recovery from lignocellulosic biomass.

Deconstruction of oriented crystalline cellulose by novel levulinic acid based deep eutectic solvents pretreatment for improved enzymatic accessibility

Discovering green solvents and their inner mechanisms for efficient deconstruction of lignocellulosic biomass recalcitrance are receiving growing interests. In this work, eco-friendly levulinic acid (LA) based deep eutectic solvents (DES) were proposed for pretreatment on moso bamboo by combining acetamide (Am), betaine (Ba) and choline chloride (ChCl) as hydrogen bonding acceptors. LA/ChCl pretreated materials showed optimal enzymatic accessibility with the highest glucose yield (79.07%) because of its higher lignin removal, morphological disruption and decreased crystallinity. Moreover, the microvoids (averagely 30 nm) and cracks were observed for cellulose microfibrils in anisotropic directions, which resulted in shorter microfibrils and crystallites facilitating the enzymatic hydrolysis. The studies on recyclability revealed that LA/Ba DES had better recycling performance due to its maintaining capability of lignin extraction. Series of supramolecular changes on oriented crystalline cellulose were determined in this work by novel LA based DES, which may provide new alternatives for biomass pretreatments.

Acid Hydrolysis of Lignocellulosic Biomass: Sugars and Furfurals Formation

Hydrolysis of lignocellulosic biomass is a crucial step for the production of sugars and biobased platform chemicals. Pretreatment experiments in a semi-continuous plant with diluted sulphuric acid as catalyst were carried out to measure the time-dependent formation of sugars (glucose, xylose, mannose), furfurals, and organic acids (acetic, formic, and levulinic acid) at different hydrolysis temperatures (180, 200, 220 °C) of one representative of each basic type of lignocellulose: hardwood, softwood, and grass. The addition of the acid catalyst is followed by a sharp increase in the sugar concentration. Xylose and mannose were mainly formed in the initial stages of the process, while glucose was released slowly. Increasing the reaction temperature had a positive effect on the formation of furfurals and organic acids, especially on hydroxymehtylfurfural (HMF) and levulinic acid, regardless of biomass type. In addition, large amounts of formic acid were released during the hydrolysis of miscanthus grass. Structural changes in the solid residue show a complete hydrolysis of hemicellulose at 180 °C and of cellulose at 200 °C after around 120 min reaction time. The results obtained in this study can be used for the optimisation of the hydrolysis conditions and reactor design to maximise the yields of desired products, which might be sugars or furfurals.

Multi-Step Exploitation of Raw Arundo donax L. for the Selective Synthesis of Second-Generation Sugars by Chemical and Biological Route

Lignocellulosic biomass represents one of the most important feedstocks for future biorefineries, being a precursor of valuable bio-products, obtainable through both chemical and biological conversion routes. Lignocellulosic biomass has a complex matrix, which requires the careful development of multi-step approaches for its complete exploitation to value-added compounds. Based on this perspective, the present work focuses on the valorization of hemicellulose and cellulose fractionsof giant reed (Arundo donax L.) to give second-generation sugars, minimizing the formation of reaction by-products. The conversion of hemicellulose to xylose was undertaken in the presence of the heterogeneous acid catalyst Amberlyst-70 under microwave irradiation. The effect of the main reaction parameters, such as temperature, reaction time, catalyst, and biomass loadings on sugars yield was studied, developing a high gravity approach. Under the optimised reaction conditions (17 wt% Arundo donax L. loading, 160 °C, Amberlyst-70/Arundo donax L. weight ratio 0.2 wt/wt), the xylose yield was 96.3 mol%. In the second step, the cellulose-rich solid residue was exploited through the chemical or enzymatic route, obtaining glucose yields of 32.5 and 56.2 mol%, respectively. This work proves the efficiency of this innovative combination of chemical and biological catalytic approaches, for the selective conversion of hemicellulose and cellulose fractions of Arundo donax L. to versatile platform products.

Consolidated bioprocessing of surfactant-assisted ionic liquid-pretreated Parthenium hysterophorus L. biomass for bioethanol production

The current study presents the first ever report of surfactant (Tween-20) assisted ionic liquid IL, (1-ethyl-3-methylimidazolium methane sulphonate [Emim][MeSO₃]) pretreatment of Parthenium hysterophorus biomass, its saccharification by in-house developed enzyme cocktail from Aspergillus aculeatus PN14, and fermentation of sugars to bioethanol under consolidated bioprocess. Optimization of pretreatment process variables viz. biomass loading, temperature and time, resulted in enhanced sugar yield (40.1%) upon saccharification of pretreated biomass with IL-stable cellulase and xylanase enzymes from an IL-tolerant newly isolated fungus Aspergillus aculeatus PN14. Physicochemical analysis of surfactant assisted IL-pretreated biomass by SEM, FT-IR and XRD provided molecular insights into inter/intra molecular ultrastructural changes in the biomass that eased the saccharification. Thorough understanding of chemical/molecular structure of biomass may help developing customized pretreatment regimes of apt severity which might result in enhanced accessibility of enzymes to biomass, and hence more sugar content.

Ultrasound and surfactant assisted ionic liquid pretreatment of sugarcane bagasse for enhancing saccharification using enzymes from an ionic liquid tolerant Aspergillus assiutensis VS34

Ionic liquid (IL) pretreatment represents an effective strategy for effective fractionation of lignocellulosic biomass (LB) to fermentable sugars in a biorefinery. Optimization of combinatorial pretreatment of sugarcane bagasse (SCB) with IL (1-butyl-3-methylimidazolium chloride [Bmim]Cl) and surfactant (PEG-8000) resulted in enhanced sugar yield (16.5%) upon enzymatic saccharification. The saccharification enzymes (cellulase and xylanase) used in the current study were in-house produced from a novel IL-tolerant fungal strain Aspergillus assiutensis VS34, isolated from chemically polluted soil, which produced adequately IL-stable enzymes. This is the first ever report of IL-stable cellulase/xylanase enzyme from Aspergillus assiutensis. To get the mechanistic insights of combinatorial pretreatment physicochemical analysis of variously pretreated biomass was executed using SEM, FT-IR, XRD, and ¹H NMR studies. The combined action of IL, surfactant and ultrasound had very severe and distinct effects on the ultrastructure of biomass that subsequently resulted in enhanced accessibility of saccharification enzymes to biomass, and increased sugar yield.

Effect of crystallinity on pretreatment and enzymatic hydrolysis of lignocellulosic biomass based on multivariate analysis

In this work, multivariate data analysis was employed to correlate variables of pretreatment process of lignocellulosic biomass. Principal component analysis and partial least square methods were performed to get the inner-relationship and data interpretation between the crystallinity and other parameters of mechanical refining-assisted sodium hydroxide pretreatment followed by enzymatic saccharification of corn stover. The PCA and PLS models showed that Sodium hydroxide dosage, mechanical refining treatment, lignin removal rate and crystallinity had close inner-related relationship with the efficiency of pretreatment and enzymolysis. Alkaline reaction and mechanical refining treatment had strong influence on the crystallinity. Multivariate data analysis revealed that pretreated corn stover samples with lower crystallinity were more easily hydrolyzed by enzyme and could get more final reducing sugar. This work could offer a new methodology to get further understanding of effect of crystallinity on the crop residue lignocellulosic biomass conversion process.

Structural changes in lignocellulosic biomass during activation with ionic liquids comprising 3-methylimidazolium cations and carboxylate anions

BACKGROUND

Lignocellulosic biomass requires either pretreatment and/or fractionation to recover its individual components for further use as intermediate building blocks for producing fuels, chemicals, and products. Numerous ionic liquids (ILs) have been investigated for biomass pretreatment or fractionation due to their ability to activate lignocellulosic biomass, thereby reducing biomass recalcitrance with minimal impact on its structural components. In this work, we studied and compared 1-allyl-3-methylimidazolium formate ([AMIM][HCOO]) to the commonly used 1-ethyl-3-methylimidazolium acetate ([EMIM][CH₃COO]) for its potential to activate hybrid poplar biomass and enable high cellulose and hemicellulose enzymatic conversion. Although [EMIM][CH₃COO] has been widely used for activation, [AMIM][HCOO] was recently identified to achieve higher biomass solubility, with an increase of 40% over [EMIM][CH₃COO].

RESULTS

Since IL activation is essentially an early stage of IL dissolution, we assessed the recalcitrance of [EMIM][CH₃COO] and [AMIM][HCOO]-activated biomass through a suite of analytical tools. More specifically, Fourier transform infrared spectroscopy and X-ray diffraction showed that activation using [AMIM][HCOO] does not deacetylate hybrid poplar as readily as [EMIM][CH₃COO] and preserves the crystallinity of the cellulose fraction, respectively. This was supported by scanning electron microscopy and enzymatic saccharification experiments in which [EMIM][CH₃COO]-activated biomass yielded almost twice the cellulose and hemicellulose conversion as compared to [AMIM][HCOO]-activated biomass.

CONCLUSION

We conclude that the IL [AMIM][HCOO] is better suited for biomass dissolution and direct product formation, whereas [EMIM][CH₃COO] remains the better IL for biomass activation and fractionation.

Accelerated effects of nano-ZnO on phosphorus removal by Chlorella vulgaris: Formation of zinc phosphate crystallites

Nanoparticles have been reported to induce toxicity to aquatic organisms, however, their potential impacts on phosphorus removal from wastewater by algae are unclear. In this study, the effects of nanoparticle ZnO (nano-ZnO) on phosphate (PO₄^3-) removal by a green alga Chlorella vulgaris were investigated. We found that PO₄^3- removal efficiency was accelerated with high concentrations of nano-ZnO (0.04-0.15mM) but reduced with low concentrations of nano-ZnO (0.005-0.04mM) compared to the control (without nano-ZnO), suggesting that PO₄^3- removal efficiency by C. vulgaris was related to nano-ZnO concentrations. Moreover, we observed changes of nano-ZnO morphology and detected element P on the surface of nano-ZnO by using transmission electronic microscopy (TEM) combined with energy dispersive X-ray spectroscopy (EDX), indicating that PO₄^3- was interacted with nano-ZnO or the dissolved Zn²⁺ from nano-ZnO. Furthermore, we confirmed this interaction induced the formation of Zn₃(PO₄)₂ crystallites sedimentation by employing X-ray diffraction analysis (XRD) and X-ray photoelectron spectroscopy (XPS), which finally accelerates the removal of PO₄^3-.

Extraction of lignin, structural characterization and bioconversion of sugarcane bagasse after ionic liquid assisted pretreatment

The primary focus of this work was to recover lignin and investigate the structural changes in sugarcane bagasse after pretreatment with ionic liquid 1-ethyl-3-methylimidazolium acetate ([EMIM]oAc). 90% lignin recovery was achieved while bagasse was treated with [EMIM]oAc at 140 °C, 120 min reaction time and 1:20 bagasse to the ionic liquid ratio (w/w). The impact of ionic liquid pretreatment on bagasse was confirmed by qualitative analysis of untreated and pretreated bagasse. Scanning electron microscopy analysis exhibited the porous and irregular structure of bagasse after pretreatment. X-ray powder diffraction analysis verified a decrease in crystallinity as a result of the pretreatment process by showing a 14.7% reduction of Crystallinity index after ionic liquid treatment. The efficacy of [EMIM]oAc on bagasse treatment was also examined by enzymatic hydrolysis which manifested an increase in reducing sugar yield as a result of pretreatment. Maximum yield of 54.3% reducing sugar was obtained after 72 h enzymatic hydrolysis of pretreated bagasse. Recovered lignin was analyzed qualitatively. 1D NMR spectroscopy of lignin revealed the presence of essential functional groups whereas 2D NMR spectroscopy showed the dominance of etherified syringyl unit. Further ionic liquid recovery and reuse were substantiated by Gel permeation chromatography analysis of lignin. Weight average molecular weight (M_w) of lignin extracted by fresh [EMIM]oAc was obtained as 1769 g/mol (in the previous study) while lignin recovered by recycled [EMIM]oAc showed almost equal M_w 1765 g/mol in this study. Thus, the current investigation corroborated satisfactory performance of [EMIM]oAc in lignocellulose processing which further enhanced enzymatic hydrolysis in the subsequent step.

Cholinium amino acids-glycerol mixtures: New class of solvents for pretreating wheat straw to facilitate enzymatic hydrolysis

New solvents for pretreating wheat straw, mixtures of cholinium amino acids ionic liquids ([Ch][AA] ILs) and glycerol, were developed. As a typical result, 50% cholinium alanine-glycerol is capable of removing 67.6% lignin while reserving 95.1% cellulose (90°C, L/S mass ratio of 20:1, 6h) and the conversions of cellulose and xylan are 89.7% and 70.9%, respectively, which is comparable to the pretreatment capability of other solvents, while [Ch][AA]-glycerol mixtures have desirable advantages, e.g., biocompatibility, lower cost with adding glycerol than pure IL, much lower pretreatment temperature (typically <100°C) than that by glycerol (typically >200°C). Lignin removal and polysaccharide conversion are dependent on [Ch][AA] content and pH of pretreatment solvents. [Ch][AA] not only remove lignin in wheat straw effectively but also swell cellulose while not remarkably dissolve cellulose with high cellulose reservation, favoring the enzymatic hydrolysis. Such mixtures of ILs and co-solvents are potential solvents for pretreating biomass.

Studies to optimize the process of biofuel production from castor stalk

Lignocellulosic biomass is a rich source of cellulose and one of the most promising raw materials for the production of biofuels and other value added chemicals. However, its high lignin content and complex cellular structure represent a significant processing challenge. In this work, the effect of pretreatment using [EMIM][Ac] was studied at various process parameters in order to develop a cost-effective process. In order to minimize the loss of sugars in this process bulk of the solids, comprising both regenerated cellulose and undissolved particles were subjected to the enzymatic hydrolysis. Up to 96% enzymatic digestibility was achieved, even with relatively coarse particle sizes (0.6–1.0 mm range), at 10% biomass loading. The enhanced digestibility of CS is attributed to reduction in lignin content, crystallinity of the cellulose coupled with an increase in surface area.

Unraveling variations of crystalline cellulose induced by ionic liquid and their effects on enzymatic hydrolysis

Ionic liquid (IL) is one of the pretreatment processes gaining considerable interests to remove the native recalcitrance of lignocellulose. But the cellulose crystalline transformation during the pretreatment and their correlations with enzymatic digestibility have not been fully elucidated. Microcrystalline cellulose (Avicel) and holocellulose, which have differential sources and original crystallinity, were respectively pretreated with 1-butyl-3-methylimidazolium chloride ([C4min]Cl). Cellulose crystalline variations as well as chemical and morphological changes were determined. Crystallinity of different materials was proved to influence the effects of pretreatment and following enzymatic digestibility. Recrystallized cellulose Iβ was revealed from slight initial cellulose Iα of Avicel, which was accomplished via formation of intermediate paracrystalline phases. The conversion yield of IL pretreated Avicel displayed no obvious changes, mainly resulted from initial high crystalline order and the recrystallization behavior. Recalcitrance of holocellulose was destroyed during cellulose allomorph transformation and hemicelluloses extraction, contributing to significant increase of glucose yield up to 92.20%. Explicit comprehension on cellulose supramolecular structure may help provide more efficient process for bioconversion after IL pretreatment.

Characterization of white poplar and eucalyptus after ionic liquid pretreatment as a function of biomass loading using X-ray diffraction and small angle neutron scattering

A systematic study was performed to understand interactions among biomass loading during ionic liquid (IL) pretreatment, biomass type and biomass structures. White poplar and eucalyptus samples were pretreated using 1-ethyl-3-methylimidazolium acetate (EmimOAc) at 110°C for 3h at biomass loadings of 5, 10, 15, 20 and 25wt%. All of the samples were chemically characterized and tested for enzymatic hydrolysis. Physical structures including biomass crystallinity and porosity were measured by X-ray diffraction (XRD) and small angle neutron scattering (SANS), respectively. SANS detected pores of radii ranging from ∼25 to 625Å, enabling assessment of contributions of pores with different sizes to increased porosity after pretreatment. Contrasting dependences of sugar conversion on white poplar and eucalyptus as a function of biomass loading were observed and cellulose crystalline structure was found to play an important role.

Nanostructured cellulose-xyloglucan blends via ionic liquid/water processing

In this work, the properties of cellulose (CE)/xyloglucan (XG) biopolymer blends are investigated, taking inspiration from the outstanding mechanical properties of plant cell walls. CE and XG were first co-solubilized in an ionic liquid, 1-ethyl-3-methylimidazolium acetate, in order to blend these biopolymers with a varying CE:XG ratio. The biopolymers were then regenerated together using water to produce solid blends in the form of films. Water-soluble XG persisted in the films following regeneration in water, indicating an attractive interaction between the CE and XG. The final CE:XG ratio of the blends was close to the initial value in solutions, further suggesting that intimate mixing takes place between CE and XG. The resulting CE/XG films were found to be free of ionic liquid, transparent and with no evidence of phase separation at the micron scale. The mechanical properties of the blend with a CE:XG ratio close to one revealed a synergistic effect for which a maximum in the elongation and stress at break was observed in combination with a high elastic modulus. Atomic force microscopy indicates a co-continuous nanostructure for this composition. It is proposed that the non-monotonous variation of the mechanical performance of the films with XG content is due to this observed nanostructuration.

Pretreatment of Lignocellulosic Biomass with Ionic Liquids and Ionic Liquid-Based Solvent Systems

Pretreatment is very important for the efficient production of value-added products from lignocellulosic biomass. However, traditional pretreatment methods have several disadvantages, including low efficiency and high pollution. This article gives an overview on the applications of ionic liquids (ILs) and IL-based solvent systems in the pretreatment of lignocellulosic biomass. It is divided into three parts: the first deals with the dissolution of biomass in ILs and IL-based solvent systems; the second focuses on the fractionation of biomass using ILs and IL-based solvent systems as solvents; the third emphasizes the enzymatic saccharification of biomass after pretreatment with ILs and IL-based solvent systems.