Bioflocculation: An alternative strategy for harvesting of microalgae - An overview

Nano-enabled microalgae bioremediation: Advances in sustainable pollutant removal and value-addition

Microalgae-assisted bioremediation, enriched by nanomaterial integration, offers a sustainable approach to environmental pollution mitigation while harnessing microalgae's potential as a biocatalyst and biorefinery resource. This strategy explores the interaction between microalgae, nanomaterials, and bioremediation, advancing sustainability objectives. The potent combination of microalgae and nanomaterials highlights the biorefinery's promise in effective pollutant removal and valuable algal byproduct production. Various nanomaterials, including metallic nanoparticles and semiconductor quantum dots, are reviewed for their roles in inorganic and organic pollutant removal and enhancement of microalgae growth. Limited studies have been conducted to establish nanomaterial's (CeO2, ZnO, Fe3O4, Al2O3, etc.) role on microalgae in pollution remediation; most studies cover inorganic pollutants (heavy metals and nutrients) remediation, exhibited 50-300% bioremediation efficiency improvement; however, some studies cover antibiotics and toxic dyes removal efficiency with 19-95% improvement. These aspects unveil the complex mechanisms underlying nanomaterial-pollutant-microalgae interactions, focusing on adsorption, photocatalysis, and quantum dot properties. Strategies to enhance bioremediation efficiency are discussed, including pollutant uptake improvement, real-time control, tailored nanomaterial design, and nutrient recovery. The review assesses recent advancements, navigates challenges, and envisions a sustainable future for bioremediation, underlining the transformative capacity of nanomaterial-driven microalgae-assisted bioremediation. This work aligns with Sustainable Development Goals 6 (Clean Water and Sanitation) and 12 (Responsible Consumption and Production) by exploring nanomaterial-enhanced microalgae bioremediation for sustainable pollution management and resource utilization.

Investigating the impacts of a recirculation sedimentation application on microalgae biomass cultivation in wastewater treatment

Commercial microalgae production is often interrupted by contamination, leading to short production cycles, reinoculation needs, and culture collapses, significantly increasing costs. This study focuses on investigating Recirculated Sedimentation Application (RSA) to control contamination in microalgae culture systems used for wastewater treatment. Chlorella vulgaris culture was grown in an unsterilized mixture of tertiary treatment effluent and centrate of anaerobic digestion wastewater sludge over a 90-day experimental period. 60 L raceway reactor was operated under a light intensity of 275 μM m-2.s-1 with a 16:8 h light-dark photoperiod. To evaluate the effect of RSA on biological-based problems, the experiment was conducted in three phases. The benefits of utilizing RSA were established through the following observations: effective removal of contaminants at an acceptable level without releasing the culture; extension of the biofilm formation time on the inner walls; inhibition of heterotrophic bacteria and nitrification; enhancement of the suspended solids retention capacity of the raceway tank (up to 770 mg.L-1); and improvement in ammonium removal rate to approximately 30 mg.L-1d-1. The ideal salinity level for both ammonium removal and biomass concentration in RSA should be below 0.02%. These findings demonstrate the potential of phycoremediation for sustainable wastewater treatment and contribute to environmental bioremediation strategies.

Sequential two-stage cultivation system using novel microalga consortia for treatment of municipal wastewater and simultaneous biomass production: Sustainable environmental management

Monoculture-based microalgae cultivation systems to treat wastewater are well-reported. Despite that, this method has some limitations in terms of nutrient removal potential, environment adaptation, and low biomass productivity. Conversely, microalgae co-cultivation and a two-stage sequential cultivation system (TSSCS) recently emerged as a promising approach to improve the treatment process and biomass productivity through better adaptation to the environment. However, no outdoor large-scale experiments were reported using this approach which hinders the viability of the process. Thus, in the present study, a sequential two-stage large-scale outdoor novel microalgae consortia experiment was developed. In first stage consortia-assisted sequential cultivation, two ratios of Tetraselmis indica (TS) and one ratio of Picochlorum sp. (PC) (2 TS:1 PC) were cultivated in a 1000-L pond containing 75%-municipal wastewater (MWW) + 25%-ASN-III, while in the second stage, 2 PC:1 TS was cultivated in two different ponds, and each containing 375-L 2 TS:1 PC-treated water + 375-L ASN-III. Outdoor parameters and nutrient removal efficiency (NRE), biomass, and biomolecule productivity such as lipid, photosynthetic pigments, astaxanthin, and β-carotene were quantified, and cost analysis was performed. At the end of the first and second stages, 2 TS:1 PC and 2 PC:1 TS showed maximum NRE of COD (68.71 and 86.40%), TN (66.98 and 94.73%), and TP (82.70 and 94.36%), respectively. Moreover, 2 TS:1 PC and 2 PC:1 TS Pond 1 and 2 produced maximum dry biomass production; 2.41 and ∼2.54 g/L contained lipid content; 36.89 and 34.90% that have 86.50 and 55.79% FAME content respectively. Similarly, 2 TS:1 PC and 2 PC:1 TS biomass exhibited valuable pigments production of astaxanthin i.e., 0.56 and 0.35 mg/g, and β-carotene; 4.65 and 2.82 mg/g, respectively. The cost analysis suggested that only microalgal-based MWW treatment was unfeasible, while valorization of produced biomass into co-products could offset the operation costs and could allow the option for the microalgal-based sustainable approach for the treatment of MWW and recovery of valuable resources.

Performance and characterization of snail adhesive mucus as a bioflocculant against toxic Microcystis

Toxic Microcystis blooms are widespread in aquatic bodies, posing major threats to aquatic and human life. Recently, bioflocculants have attracted considerable attention as a promising biomaterial for Microcystis management. In search of a novel organism that can produce an efficient bioflocculant for controlling harmful algae sustainably, the native gastropod Cipangopaludina chinensis was co-cultured continuously with toxic Microcystis under different initial algal cell densities. The bioflocculation effect of snail mucus on toxic Microcystis, microcystin removal, and toxin accumulation in snails was investigated. In addition, the properties of the adhesive mucus were characterized using microscopic, X-ray diffraction, infrared spectroscopy, and polysaccharide and proteome analyses. Microcystis cells were captured and flocculated by the snail mucus; removal efficiencies of up to 89.9% and 84.8% were achieved for microalgae and microcystin-leucine arginine (MC-LR), respectively, when co-cultured with C. chinensis for only one day. After nine-day exposure, less than 5.49 µg/kg DW microcystins accumulated in the snails, indicating safety for human consumption. The snail mucus contained 104.3 µg/mg protein and 72.7 µg/mg carbohydrate, which provide several functional groups beneficial for Microcystis bioflocculation. The main monosaccharide subunits of polysaccharides are galactose, galactosamine, glucosamine, fucose, glucose, and mannose. Most of them are key components of polysaccharides in many bioflocculants. Gene Ontology analysis indicated the protein enrichment in binding processes and catalytic activity, which may account for Microcystis bioflocculation via protein binding or enzymatic reactions. The findings indicate that native C. chinensis secretes adhesive mucus that can act as bioflocculant for toxic Microcystis from ambient water and can be an effective and eco-friendly tool for Microcystis suppression.

Recent advances in microalgal production, harvesting, prediction, optimization, and control strategies

The market value of microalgae has grown exponentially over the past two decades, due to their use in the pharmaceutical, nutraceutical, cosmetic, and aquatic/animal feed industries. In particular, high-value products such as omega-3 fatty acids, proteins, and pigments derived from microalgae have high demand. However, the supply of these high-value microalgal bioproducts is hampered by several critical factors, including low biomass and bioproduct yields, inefficiencies in monitoring microalgal growth, and costly harvesting methods. To overcome these constraints, strategies such as synthetic biology, bubble generation, photobioreactor designs, electro-/magnetic-/bioflocculation, and artificial intelligence integration in microalgal production are being explored. These strategies have significant promise in improving the production of microalgae, which will further boost market availability of algal-derived bioproducts. This review focuses on the recent advances in these technologies. Furthermore, this review aims to provide a critical analysis of the challenges in existing algae bioprocessing methods, and highlights future research directions.

Trends on Chlamydomonas reinhardtii growth regimes and bioproducts

The green microalga Chlamydomonas reinhardtii is a model microorganism for several areas of study. Among the different microalgae species, it presents advantageous characteristics, such as genomes completely sequenced and well-established techniques for genetic transformation. Despite that, C. reinhardtii production is still not easily commercially viable, especially due to the low biomass yield. So far there are no reports of scientometric study focusing only on C. reinhardtii biomass production process. Considering the need for culture optimization, a scientometric research was conducted to analyze the papers that investigated the growth regimes effects in C. reinhardtii cultivation. The search resulted in 130 papers indexed on Web of Science and Scopus platforms from 1969 to December 2022. The quantitative analysis indicated that the photoautotrophic regime was the most employed in the papers. However, when comparing the three growth regimes, the mixotrophic one led to the highest production of biomass, lipids, and heterologous protein. The production of bioproducts was considered the main objective of most of the papers and, among them, biomass was the most frequently investigated. The highest biomass production reported among the papers was 40 g L-1 in the heterotrophic growth of a transgenic strain. Other culture conditions were also crucial for C. reinhardtii growth, for instance, temperature and cultivation process.

Technologies for harvesting the microalgae for industrial applications: Current trends and perspectives

Microalgae are emerging as a promising source for augmenting the supply of essential products to meet global demands in an environmentally sustainable manner. Despite the potential benefits of microalgae in industry, the high energy consumption for harvesting remains a significant obstacle. This review offers a comprehensive overview of microalgae harvesting technologies and their industrial applications, with particular emphasis on the latest advances in flocculation techniques. These cutting-edge methods have been applied to biodiesel production, food and nutraceutical processing, and wastewater treatment. Large-scale harvesting is still severely impeded by the high cost despite progress has been made in laboratory studies. In the future, cost-effective microalgal harvesting will rely on efficient resource utilization, including the use of waste materials and the reuse of media and flocculants. Additionally, precise regulation of biological metabolism will be necessary to overcome algal species-related limitations through the development of extracellular polymeric substance-induced flocculation technology.

Phycoremediation of heavy metals and production of biofuel from generated algal biomass: a review

Due to human activity and natural processes, heavy metal contamination frequently affects the earth's water resources. The pollution can be categorized as resistant and persistent since it poses a significant risk to terrestrial and marine biological systems and human health. Because of this, several appeals and demands have been made worldwide to try and clean up these contaminants. Through bioremediation, algal cells are frequently employed to adsorb and eliminate heavy metals from the environment. Bioremediation is seen as a desirable strategy with few adverse effects and low cost. Activities and procedures for bioremediation involving algal cells depend on various environmental factors, including salinity, pH, temperature, the concentration of heavy metals, the amount of alga biomass, and food availability. Additionally, the effectiveness of removing heavy metals from the environment by assessing how environmental circumstances affect algal activities. The main issues discussed are (1) heavy metal pollution of water bodies, the role of algal cells in heavy metal removal, the methods by which algae cells take up and store heavy metals, and the process of turning the algae biomass produced into biofuel. (2) To overcome the environmental factors and improve heavy metals bioremediation, many strategies are applied, such as immobilizing the cells, consortium culture, and using dry mass rather than living cells. (3) The processes for converting produced algal biomass into biofuels like biodiesel and biomethanol. The present study discusses the life cycle assessment and the limitations of biofuel products from algae biomass.

Symbiotic relationship between filamentous algae (Halomicronema sp.) and extracellular polymeric substance-producing algae (Chlamydomonas sp.) through biomimetic simulation of natural algal mats

To lower the cost of biomass harvesting, the growth of natural biofilm is considered to be an optimal alternative to microalgae aggregation. This study investigated algal mats that naturally agglomerate into a lump and float on water surfaces. Halomicronema sp., a filamentous cyanobacterium with high cell aggregation and adhesion to substrates, and Chlamydomonas sp., which grows rapidly and produces high extracellular polymeric substances (EPS) in certain environments, are the main microalgae that make up selected mats through next-generation sequencing analysis. These two species play a major role in the formation of solid mats, and showed a symbiotic relationship as the medium and nutritional source, particularly owing to the large amount of EPS formed by the reaction between EPS and calcium ions through zeta potential and Fourier-transform infrared spectroscopy analysis. This led to the formation of an ecological biomimetic algal mat (BAM) that mimics the natural algal mat system, and this is a way to reduce costs in the biomass production process as there is no separate treatment process for harvesting.

Heavy metal tolerance in microalgae: Detoxification mechanisms and applications

The proficiency of microalgae to resist heavy metals has potential to be beneficial in resolving various environmental challenges. Global situations such as the need for cost-effective and ecological ways of remediation of contaminated water and for the development of bioenergy sources could employ microalgae. In a medium with the presence of heavy metals, microalgae utilize different mechanisms to uptake the metal and further detoxify it. Biosorption and the next process of bioaccumulation are two such major steps and they also include the assistance of different transporters at different stages of heavy metal tolerance. This capability has also proved to be efficient in eradicating many heavy metals like Chromium, Copper, Lead, Arsenic, Mercury, Nickel and Cadmium from the environment they are present in. This indicates the possibility of the application of microalgae as a biological way of remediating contaminated water. Heavy metal resistance quality also allows various microalgal species to contribute in the generation of biofuels like biodiesel and biohydrogen. Many research works have also explored the capacity of microalgae in nanotechnology for the formation of nanoparticles due to its relevant characteristics. Various studies have also revealed that biochar deduced from microalgae or a combination of biochar and microalgae can have wide applications specially in deprivation of heavy metals from an environment. This review focuses on the strategies adopted by microalgae, various transporters involved in the process of tolerating heavy metals and the applications where microalgae can participate owing to its ability to resist metals.

Strategy for the formation of microalgae-bacteria aggregates in high-rate algal ponds

This work studied the formation of aggregates used for wastewater treatment in high-rate algal ponds (HRAP). For this, the establishment of microalgae-bacteria aggregates in these systems was evaluated, considering strategies for the inoculation and start-up. Two HRAP were operated in parallel, at first in batch mode and then in continuous flow. The wastewater treatment was efficient, with removal rates around 80% for COD and N-ammoniacal. Volatile suspended solids and chlorophyll for the culture grew continuously reached a concentration of 548 ± 11 mg L^-1 and 7.8 mg L^-1, respectively. Larger photogranules were observed when the system was placed in a continuous regime. The protein fraction of extracellular polymeric substances was identified as a determinant in photogranules formation. During the continuous regime, more than 50% of the biomass was higher than 0.2 mm, flocculation efficiency of 78 ± 6%, and the volumetric sludge index of 32 ± 5 mL g^-1. The genetic sequencing showed the growth of cyanobacteria in the aggregate and the presence of microalgae from the chlorophytes and diatoms groups in the final biomass.

Base type determines the effects of nucleoside monophosphates on microalgae-bacteria symbiotic systems

Microalgae are promising sources of clean energy. Bioflocculation by cocultured bacteria is an effective way to harvest microalgae. As a key foundation for microorganisms, phosphorus is theoretically effective in shaping microalgae production and flocculation. In this study, the impacts of 23 nucleoside monophosphates on Auxenochlorella pyrenoidosa growth, lipid synthesis, and self-settlement and on the symbiotic bacterial system were investigated. Adenosine monophosphate was the most effective in enhancing microalgae development (2.14-3.16 × 10⁸ cells/mL) and lipid production (average 10.48%) and resulted in a low settling velocity. Samples were divided into two groups, purine and pyrimidine feeding, according to a random forest analysis (OOB = 0%, p < 0.001). Purine feeding resulted in the highest soluble extracellular protein and polysaccharide secretion (p < 0.01). KEGG ortholog count prediction of functional genes related to biofilm formation was conducted using PICRUSt2, and significant upregulation (FC ≥ 1.77, p < 0.05) of the extracellular polymeric substance formation functional group was observed in the adenosine and guanosine treatments. The symbiotic bacterial community structure differed substantially between purine- and pyrimidine-feeding systems. In summary, these results indicated that the effect of nucleoside monophosphates on the microalgae-bacteria system is determined by the base type (purine or pyrimidine) rather than the molecular structure (cyclic or noncyclic).

Chitosan-coated oleaginous microalgae-fungal pellets for improved bioremediation of non-sterile secondary effluent and application in carbon dioxide sequestration in bubble column photobioreactors

Oleaginous microalga Scenedesmus sp. SPP was rapidly immobilized in oleaginous fungal pellets by their opposite-surface-charges. Microalgae-fungal (MF) pellets were more effective in bioremediation of non-sterile secondary effluent than mono-culture. The optimal hydraulic retention time for dual bioremediation in semi-continuous mode was 72 h. The MF pellets coated with 0.4 %-chitosan improved removal efficiencies of COD, total nitrogen (TN), and total phosphorus (TP) up to 96.2±0.0 %, 88.2±2.8 % and 71.5±0.7 %, respectively, likely because of better cell retention and more nutrient adsorption and assimilation. Dual bioremediation by coated MF pellets was also successfully scaled up in 30-L bubble-column photobioreactors with improved COD, TN, and TP removal efficiencies of 98.5±0.0 %, 90.2±0.0 % and 79.5±2.1 %, respectively. This system also effectively removed CO₂ from simulated flue gas at 71.2±0.4 % and produced biomass with high lipid content. These results highlight the effectiveness of bio-immobilization by fungal pellets; chitosan coating; and their practical applications in bioremediation and CO₂ sequestration.

Recent advancements in cadmium-microbe interactive relations and their application for environmental remediation: a mechanistic overview

The toxic and persistent nature of cadmium (Cd) in the environment has become a matter of concern with its drastic increase in the concentrations over past few decades. Among the various techniques, the microbial remediation has been accepted as an effective decontamination tool for environmental applications, which is sustainable over a period of time. The Cd decontamination potential of the microbes depends on various internal and external factors that play a crucial role in selection of the microbes for application in a particular environment. Thus, it is important to understand the role of these factors for optimal application of the microbes. This study provides an insight into the mechanisms involved between the microbes and the environmental Cd. The study also briefly reviews the mathematical models that have been used to predict the remediation potential of the microbes and the kinetics involved during the process. A critical analysis of the recent advancements in the techniques for use of bacteria, fungi, and algal cells to remove Cd has been also presented in the manuscript.

Advanced treatment of secondary effluent from wastewater treatment plant by a newly isolated microalga Desmodesmus sp. SNN1

Secondary effluents contain considerable amounts of nitrogen and phosphorous, which if dumped untreated can cause eutrophication of the receiving water bodies. Microalgae can remove these nutrients and other pollutants from the wastewater effluents and play an effective role in the secondary effluent treatment. In this study, six microalgae strains (SNN1, SNN2, SNN3, SNN4, SNS1, and SNS2) were isolated and screened from the water and mud of Yingxue Lake of Shandong Jianzhu University, and their efficiencies for the removal of COD, NH₄ ⁺-N, TN, and TP in the secondary effluent were assessed. By comparing the growth performances and nutrient removal ability of algal strains in domestic sewage, we found that SNN1 (identified and named as Desmodesmus sp. SNN1) has the highest efficiency for biomass accumulation and sewage purification. Hence, the algal strain SNN1 was selected for further screening and optimization experiments. The strain showed higher biomass yield and better nutrient removal rate when the pH of secondary effluent was 9.0 and the initial inoculum concentration (optical density at 680 nm) of algal strain was 0.4. After 12 days of treatment, the concentrations of COD, NH₄ ⁺-N, TN, and TP in the secondary effluent were 31.79, 0.008, 8.631, and 0.069 mg/L, respectively. Therefore, SNN1 with the removal rates of 52.69% (COD), 99.99% (NH₄ ⁺-N), 89.09% (TN), and 94.64% (TP) displayed its high potential in nutrient removal. In addition, it also yielded 5.30 mg/L of chlorophyll a and 168.33 mg/L of lipids. These results demonstrated that this strain exhibited an effective treatment capacity for secondary effluent and microalgal oil production. This study is helpful to provide a strategy for the resource utilization of secondary effluent and the conservation of freshwater resources required by microalgae culture.

Dietary-Polysaccharide-Modified Fish-Oil-Based Double Emulsion as a Functional Colloidal Formulation for Oral Drug Delivery

Oral delivery is the most convenient drug administration route. However, oral delivery of peptides is extremely challenging due to the physical and chemical barriers within the gastrointestinal tract. Polysaccharides are often utilized as polymeric biomaterials in drug delivery. Among these, dietary polysaccharides extracted from okra, yam, and spirulina have been reported to stimulate innate immunity with well-known nutritional benefits. In this study, we developed a dietary-polysaccharide-modified fish-oil-based emulsion for oral co-delivery of a hydrophilic PD-L1 blocking peptide and the hydrophobic small molecule simvastatin. The optimal emulsion was nano-sized and exhibited a negative surface charge, high drug encapsulation efficiency of over 97%, low viscosity, and sustained drug release manner. The formulation could significantly increase the uptake of peptides by intestinal Caco-2 cells, which demonstrated the great potential of the formulation for promoting the oral absorption of peptides. Additionally, these dietary polysaccharides could promote dendritic cell maturation and cytokine expression in macrophages, demonstrating that these nutraceutical polysaccharides had dual roles of functioning as promising colloidal delivery systems and as potential immune modulators or adjuvants. Thus, this food-based colloidal delivery system shows promise for the oral delivery of peptide drugs and lays a great platform for future applications in immunotherapy.

Microalgae Harvesting after Tertiary Wastewater Treatment with White-Rot Fungi

Tertiary wastewater treatment with microalgae incorporates environmental sustainability with future technologies and high exploitation costs. Despite the apparent ecological benefits of microalgae-assisted wastewater treatment/biomass-based resource production, technological improvements are still essential to compete with other technologies. Bio-flocculation instead of mechanical harvesting has been demonstrated as an alternative cost-effective approach. So far, mostly filamentous fungi of genus Aspergillus have been used for this purpose. Within this study, we demonstrate a novel approach of using white-rot fungi, with especially high potential of algae-Irpex lacteus complex that demonstrates efficiency with various microalgae species at a broad range of temperatures (5-20 °C) and various pH levels. Harvesting of microalgae from primary and secondary wastewater resulted in 73-93% removal efficiencies within the first 24 h and up to 95% after 48 h. The apparent reuse potential of the algae-I. lacteus pellets further complements the reduced operating costs and environmental sustainability of bio-flocculation technology.

Understanding the influence of free nitrous acid on microalgal-bacterial consortium in wastewater treatment: A critical review

Microalgal-bacterial consortium (MBC) constitutes a sustainable and efficient alternative to the conventional activated sludge process for wastewater treatment (WWT). Recently, integrating the MBC process with nitritation (i.e., shortcut MBC) has been proposed to achieve added benefits of reduced carbon and aeration requirements. In the shortcut MBC system, nitrite or free nitrous acid (FNA) accumulation exerts antimicrobial influences that disrupt the stable process performance. In this review, the formation and interactions that influence the performance of the MBC were firstly summarized. Then the influence of FNA on microalgal and bacterial monocultures and related mechanisms together with the knowledge gaps of FNA influence on the shortcut MBC were highlighted. Other challenges and future perspectives that impact the scale-up of the shortcut MBC for WWT were illustrated. A potential roadmap is proposed on how to maximize the stable operation of the shortcut MBC system for sustainable WWT and high-value biomass production.

Recent progress on converting CO2 into microalgal biomass using suspended photobioreactors

Inhomogeneous light distribution and poor CO₂ transfer capacity are two critical concerns impeding microalgal photosynthesis in practical suspended photobioreactors (PBRs). To provide valuable guidance on designing high-performance PBRs, recent progress on enhancing light and CO₂ availabilities is systematically summarized in this review. Particularly, for the first time, the strategies on elevating light availability are classified and discussed from the perspectives of increasing incident light intensity, introducing internal illumination, optimizing flow field, regulating biomass concentrations, and enlarging illumination surface areas. Meanwhile, the strategies on enhancing CO₂ light availability are outlined from the aspects of generating smaller bubbles, extending bubbles residence time, and facilitating CO₂ dissolution using extra additives. Given the microalgal biomass production using current PBRs are still suffering from low productivity and economic feasibility, the possible future directions for PBRs implementation and development are presented. Altogether, this review is beneficial to furthering development of PBRs as a practical technology.

Fungal Contamination in Microalgal Cultivation: Biological and Biotechnological Aspects of Fungi-Microalgae Interaction

In the last few decades, the increasing interest in microalgae as sources of new biomolecules and environmental remediators stimulated scientists’ investigations and industrial applications. Nowadays, microalgae are exploited in different fields such as cosmeceuticals, nutraceuticals and as human and animal food supplements. Microalgae can be grown using various cultivation systems depending on their final application. One of the main problems in microalgae cultivations is the possible presence of biological contaminants. Fungi, among the main contaminants in microalgal cultures, are able to influence the production and quality of biomass significantly. Here, we describe fungal contamination considering both shortcomings and benefits of fungi-microalgae interactions, highlighting the biological aspects of this interaction and the possible biotechnological applications.

Bio-flocculation of Microcystis aeruginosa by using fungal pellets of Aspergillus oryzae: Performance and mechanism

Algal blooms caused by eutrophication are global phenomena that seriously threaten the sustainable use of freshwater resources. Traditional water treatment chemicals often typically lead to high levels of residue and cause damage to the morphology of algal cells. This study investigated an eco-friendly fungal bio-flocculant, Aspergillus oryzae, to remove the representative microalgae (Microcystis aeruginosa). Furthermore, it explored crucial flocculation parameters, adsorption kinetics, and thermodynamics of microalgae using A. oryzae. Accordingly, a flocculation efficiency of >95% was achieved when the fungus was cultured for six days, flocculant dosage was 11 g/L, rotation speed was 100 rpm, temperature was 25 °C, flocculation time was 5 h, and pH ranged between 4.0 and 9.0. KEGG analysis based on the genomic data, and chemical composition analysis revealed that proteins and polysaccharides were the major components of metabolites. Zeta potential analysis, scanning electron microscopy, three-dimensional fluorescence, X-ray spectroscopy, and infrared spectroscopy, electrostatic attraction revealed that electrostatic attraction promoted the destabilization and aggregation of microalgae. Additionally, hyphal surface adsorption and chemisorption from extracellular proteins and exopolysaccharides aided in the removal of microalgae. Therefore, fungi-based bio-flocculants have the potential to remove microalgae in a simple, effective, and eco-friendly manner without the complex extraction of extracellular metabolites.

Effects of harvesting on morphological and biochemical characteristics of microalgal biomass harvested by polyacrylamide addition, pH-induced flocculation, and centrifugation

The effects of microalgae harvesting methods on microalgal biomass quality were evaluated using three species namely the freshwater green alga Chlorella vulgaris, marine red alga Porphyridium purpureum and marine diatom Phaeodactylum tricornutum. Harvesting efficiencies of polyacrylamide addition, alkaline addition, and centrifugation ranged from 85 to 95, 59-92 and 100%, respectively, across these species. Morphology of the harvested cells (i.e. compromised cell walls) was significantly impacted by alkaline pH-induced flocculation for all three species. Over 50% of C. vulgaris cells were compromised with alkaline pH compared to < 10% with polyacrylamide and centrifugation. The metabolic profiles varied depending on harvesting methods. Species-specific decrease of certain metabolites was observed. These results suggest that the method of harvest can alter the metabolic profile of the biomass amongst the three harvesting methods, polyacrylamide addition showed higher harvesting efficiency with less compromised cells and higher retention of industry important biochemicals.

Effective recovery of microalgal biomass using various types of emulsion polymers

Microalgae biomass has been considered as one of the potential feedstocks in biofuel production. Yet, biomass harvesting poses a challenge to the overall production cost due to its low cell density. Flocculation has been marked as one of the promising processes in microalgae harvesting technology. In this study, the first screening of two anionic (A-230, and A-330E) and five cationic polymers (C-810E, C-810EL, C-810EB, C-810ELH, and C-810EMB) followed by gravity settling with the mixed microalgae concentration of 2.24 g_TSS/L revealed that anionic polymers are less effective. Whereas all cationic polymers achieved above 90% harvesting efficiency. Therefore, the maximum mass recovery of 98.7% with 86.8 g_TSS/L sediment content was achieved by adjusting pH to 6-0.6 mL/L (115.178 mg/g_biomass) of C-810E followed by 15-min settling. The cationic polymer addition followed by settling would enable cost-effective downstream processing of microalgal biomass.

Optimization of Microalgae–Bacteria Consortium in the Treatment of Paper Pulp Wastewater

The microalgae–bacteria consortium is a promising and sustainable alternative for industrial wastewater treatment, since it may allow good removal of organic matter and nutrients, as well as the possibility of producing products with added value from the algae biomass. This research investigated the best bacterial and microalgae inoculation ratio for system start-up and evaluation of removing organic matter (as chemical oxygen demand (COD)), ammoniacal nitrogen (NH4+–N), nitrite nitrogen (NO2−–N), nitrate nitrogen (NO3−–N), phosphate phosphorus (PO43−–P) and biomass formation parameters in six photobioreactors with a total volume of 1000 mL. Reactors were operated for 14 days with the following ratios of pulp mill biomass aerobic (BA) and Scenedesmus sp. microalgae (MA): 0:1 (PBR1), 1:0 (PBR2), 1:1 (PBR3), 3:1 (PBR4), 5:1 (PBR5), and 1:3 (PBR6). Results show that COD removal was observed in just two days of operation in PBR4, PBR5, and PBR6, whereas for the other reactors (with a lower rate of initial inoculation) it took five days. The PBR5 and PBR6 performed better in terms of NH4+–N removal, with 86.81% and 77.11%, respectively, which can be attributed to assimilation by microalgae and nitrification by bacteria. PBR6, with the highest concentration of microalgae, had the higher PO43−–P removal (86%), showing the advantage of algae in consortium with bacteria for phosphorus uptake. PBR4 and PBR5, with the highest BA, led to a better biomass production and sedimentability on the second day of operation, with flocculation efficiencies values over 90%. Regarding the formation of extracellular polymeric substances (EPS), protein production was substantially higher in PBR4 and PBR5, with more BA, with average concentrations of 49.90 mg/L and 49.05 mg/L, respectively. The presence of cyanobacteria and Chlorophyceae was identified in all reactors except PBR1 (only MA), which may indicate a good formation and structuring of the microalgae–bacteria consortium. Scanning electron microscopy (SEM) analysis revealed that filamentous microalgae were employed as a foundation for the fixation of bacteria and other algae colonies.

Natural Polymers and Their Nanocomposites Used for Environmental Applications

The aim of this review is to bring together the main natural polymer applications for environmental remediation, as a class of nexus materials with advanced properties that offer the opportunity of integration in single or simultaneous decontamination processes. By identifying the main natural polymers derived from agro-industrial sources or monomers converted by biotechnology into sustainable polymers, the paper offers the main performances identified in the literature for: (i) the treatment of water contaminated with heavy metals and emerging pollutants such as dyes and organics, (ii) the decontamination and remediation of soils, and (iii) the reduction in the number of suspended solids of a particulate matter (PM) type in the atmosphere. Because nanotechnology offers new horizons in materials science, nanocomposite tunable polymers are also studied and presented as promising materials in the context of developing sustainable and integrated products in society to ensure quality of life. As a class of future smart materials, the natural polymers and their nanocomposites are obtained from renewable resources, which are inexpensive materials with high surface area, porosity, and high adsorption properties due to their various functional groups. The information gathered in this review paper is based on the publications in the field from the last two decades. The future perspectives of these fascinating materials should take into account the scale-up, the toxicity of nanoparticles, and the competition with food production, as well as the environmental regulations.

Sustainable microalgal biomass production in food industry wastewater for low-cost biorefinery products: a review

Microalgae are recognized as cell factories enriched with biochemicals suitable as feedstock for bio-energy, food, feed, pharmaceuticals, and nutraceuticals applications. The industrial application of microalgae is challenging due to hurdles associated with mass cultivation and biomass recovery. The scale-up production of microalgal biomass in freshwater is not a sustainable solution due to the projected increase of freshwater demands in the coming years. Microalgae cultivation in wastewater is encouraged in recent years for sustainable bioeconomy from biorefinery processes. Wastewater from the food industry is a less-toxic growth medium for microalgal biomass production. Traditional wastewater treatment and management processes are expensive; hence it is highly relevant to use low-cost wastewater treatment processes with revenue generation through different products. Microalgae are accepted as potential biocatalysts for the bioremediation of wastewater. Microalgae based purification of wastewater technology could be a universal alternative solution for the recovery of resources from wastewater for low-cost biomass feedstock for industry. This review highlights the importance of microalgal biomass production in food processing wastewater, their characteristics, and different microalgal cultivation methods, followed by nutrient absorption mechanisms. Towards the end of the review, different microalgae biomass harvesting processes with biorefinery products, and void gaps that tend to hinder the biomass production with future perspectives will be intended. Thus, the review could claim to be valuable for sustainable microalgae biomass production for eco-friendly bioproduct conversions.

Graphical abstract

Recent Advances of Microalgae Exopolysaccharides for Application as Bioflocculants

Microalgae are used in flocculation processes because biopolymers are released into the culture medium. Microalgal cell growth under specific conditions (temperature, pH, luminosity, nutrients, and salinity) provides the production and release of exopolysaccharides (EPS). These biopolymers can be recovered from the medium for application as bioflocculants or used directly in cultivation as microalgae autoflocculants. The optimization of nutritional parameters, the control of process conditions, and the possibility of scaling up allow the production and industrial application of microalgal EPS. Therefore, this review addresses the potential use of EPS produced by microalgae in bioflocculation. The recovery, determination, and quantification techniques for these biopolymers are also addressed. Moreover, other technological applications of EPS are highlighted.

Microalgae based wastewater treatment coupled to the production of high value agricultural products: Current needs and challenges

One of the main social and economic challenges of the 21st century will be to overcome the worlds' water deficit expected by the end of this decade. Microalgae based wastewater treatment has been suggested as a strategy to recover nutrients from wastewater while simultaneously producing clean water. Consortia of microalgae and bacteria are responsible for recovering nutrients from wastewater. A better understanding of how environmental and operational conditions affect the composition of the microalgae-bacteria consortia would allow to maximise nutrient recoveries and biomass productivities. Most of the studies reported to date showed promising results, although up-scaling of these processes to reactors larger than 100 m² is needed to better predict their industrial relevance. The main advantage of microalgae based wastewater treatment is that valuable biomass with unlimited applications is produced as a co-product. The aim of the current paper was to review microalgae based wastewater treatment processes focusing on strategies that allow increasing both biomass productivities and nutrient recoveries. Moreover, the benefits of microalgae based agricultural products were also discussed.

Reproducibility of Aerobic Granules in Treating Low-Strength and Low-C/N-Ratio Wastewater and Associated Microbial Community Structure

Long-term stability of the aerobic granular sludge system is essentially based on the microbial community structure of the biomass. In this study, the physicochemical and microbial characteristics of sludge and wastewater treatment performance were investigated regarding formation, maturation, and long-term maintenance of granules in two parallel sequencing batch reactors (SBR), R1 and R2, under identical conditions. The aim was to explore the linkage between microbial community structure of the aerobic granules, their long-term stability, as well as the reproducibility of granulation and long-term stability. The two reactors were operated with a COD concentration of 400 mg/L and a chemical oxygen demand to nitrogen (COD/N) ratio of 4:1 under anoxic–oxic conditions. It was found that although SVI30, sludge size, and distributions in R1 and R2 were different, aerobic granules were formed, and they maintained long-term stability in both reactors for 320 days, implying that a certain level of randomness of granulation does not affect the long-term stability and performance for COD and N removal. In addition, a significant reduction in the richness and diversity of microbial production was observed after the sludge was converted from inoculum or flocs to granules, but this did not negatively affect the performance of wastewater treatment. Among the predominant microbial species in aerobic granules, Zoogloea was identified as the most important bacteria present during the whole operation with the highest abundance, while Thauera was the important genus in the formation and maturation of the aerobic granules, but it cannot be maintained long-term due to the low food-to-microorganisms ratio (F/M) in the system. In addition, some species from Ohtaekwangia, Chryseobacterium, Taibaiella, and Tahibacter were found to proliferate strongly during long-term maintenance of aerobic granules. They may play an important role in the long-term stability of aerobic granules. These results demonstrate the reproducibility of granulation, the small influence of granulation on long-term stability, and the robustness of aerobic granulation for the removal of COD and N. Overall, our study contributes significantly to the understanding of microbial community structure for the long-term stability of aerobic granular sludge in the treatment of low-COD and low-COD/N-ratio wastewater in practice.

Microalgae harvesting techniques: updates and recent technological interventions

Microalgal biomass has garnered attention as a renewable and sustainable resource for producing biodiesel. The harvesting of microalgal biomass is a significant bottleneck being faced by the industries as it is the crucial cost driver in the downstream processing of biomass. Bioharvesting of microalgal biomass mediated by: microbial, animal, and plant-based polymeric flocculants has gained a higher probability of utility in accumulation due to: its higher dewatering potential, less toxicity, and ecofriendly properties. The present review summarizes the key challenges and the technological advancements associated with various such harvesting techniques. The economic and technical aspects of different microalgal harvesting techniques, particularly the cationic polymeric flocculant-based harvesting of microalgal biomass, are also discussed. Furthermore, interactions of flocculants with microalgal biomass and the effects of these interactions on metabolite and lipid extractions are discussed to offer a promising solution for suitability in selecting the most efficient and economical method of microalgal biomass harvesting for cost-effective biodiesel production.

Microalgae Biomass as a New Potential Source of Sustainable Green Lubricants

Lubricants are materials able to reduce friction and/or wear of any type of moving surfaces facilitating smooth operations, maintaining reliable machine functions, and reducing risks of failures while contributing to energy savings. At present, most worldwide used lubricants are derived from crude oil. However, production, usage and disposal of these lubricants have significant impact on environment and health. Hence, there is a growing pressure to reduce demand of this sort of lubricants, which has fostered development and use of green lubricants, as vegetable oil-based lubricants (biolubricants). Despite the ecological benefits of producing/using biolubricants, availability of the required raw materials and agricultural land to create a reliable chain supply is still far from being established. Recently, biomass from some microalgae species has attracted attention due to their capacity to produce high-value lipids/oils for potential lubricants production. Thus, this multidisciplinary work reviews the main chemical-physical characteristics of lubricants and the main attempts and progress on microalgae biomass production for developing oils with pertinent lubricating properties. In addition, potential microalgae strains and chemical modifications to their oils to produce lubricants for different industrial applications are identified. Finally, a guide for microalgae oil selection based on its chemical composition for specific lubricant applications is provided.

A bacterial strain Citrobacter W4 facilitates the bio-flocculation of wastewater cultured microalgae Chlorella pyrenoidosa

A bacteria strain Citrobacter W4 isolated from the microalgae sewage culture system showed flocculating activity against Chlorella pyrenoidosa. In this work, operation parameters under outdoor conditions were optimized. When the bacterial-algal ratio was 4:1, G value was 26.30 s^-1, and harvesting time was 6 h, the harvesting efficiency achieved 87.37 ± 2.96% without ions addition and pH adjustment. The microbial community structure analysis showed Citrobacter W4 was dominant in the harvesting process. Flocculating active substances were on the surface and metabolites of Citrobacter W4. The main component of bacteria flocculating active substances was protein. Polysaccharides and carboxylic acid also promoted flocculation. The flocculation mechanisms were mainly adsorption bridging, net catching, and sweeping, not electric neutralization. The quality of FAMEs was improved after flocculation. The cost of 1 kg dried microalgae flocculated by Citrobacter W4 was $1.35. The novel flocculating bacteria showed the potential to harvest microalgae cost-effectively and environmentally friendly.

Constructed microalgal-bacterial symbiotic (MBS) system: Classification, performance, partnerships and perspectives

The microalgal-bacterial symbiotic (MBS) system shows great advantages in the synchronous implementation of wastewater treatment and nutrient recovery. To enhance the understanding of different MBS systems, this review summarizes reported MBS systems and proposes three patterns according to the living state of microalgae and bacteria. They are free microalgal-bacterial (FMB) system, attached microalgal-bacterial (AMB) system and bioflocculated microalgal-bacterial (BMB) system. Compared with the other two patterns, BMB system shows the advantages of microalgal biomass harvesting and application. To further understand the microalgal-bacterial partnerships in the bioflocculation of BMB system, this review discusses bioflocs characteristics, extracellular polymeric substances (EPS) properties and production, and the effect of microalgae/bacteria ratio and microalgal strains on the formation of bioflocculation. Microalgal biomass production and application are important for BMB system development in the future. Food processing wastewater characterized by high biodegradability and low toxicity should be conducive for microalgal cultivation. In addition, exogenous addition of functional bacteria for nutrient removal and bioflocculation formation would be a crucial research direction to facilitate the large-scale application of BMB system.

Mass cultivation and harvesting of microalgal biomass: Current trends and future perspectives

Microalgae are unicellular photosynthetic organisms capable of producing high-value metabolites like carbohydrates, lipids, proteins, polyunsaturated fatty acids, vitamins, pigments, and other high-value metabolites. Microalgal biomass gained more interest for the production of nutraceuticals, pharmaceuticals, therapeutics, food supplements, feed, biofuel, bio-fertilizers, etc. due to its high lipid and other high-value metabolite content. Microalgal biomass has the potential to convert trapped solar energy to organic materials and potential metabolites of nutraceutical and industrial interest. They have higher efficiency to fix carbon dioxide (CO₂) and subsequently convert it into biomass and compounds of potential interest. However, to make microalgae a potential industrial candidate, cost-effective cultivation systems and harvesting methods for increasing biomass yield and reducing the cost of downstream processing have become extremely urgent and important. In this review, the current development in different microalgal cultivation systems and harvesting methods has been discussed.

Recent progress in flocculation, dewatering, and drying technologies for microalgae utilization: Scalable and low-cost harvesting process development

Microalgal research has made significant progress in terms of the high-value-added industrial application of microalgal biomass and its derivatives. However, cost-effective techniques for producing, harvesting, and processing microalgal biomass on a large scale still need to be fully explored in order to optimize their performance and achieve commercial robustness. In particular, technologies for harvesting microalgae are critical in the practical process as they require excessive energy and equipment costs. This review focuses on microalgal flocculation, dewatering, and drying techniques and specifically covers the traditional approaches and recent technological progress in harvesting microalgal biomass. Several aspects, including the characteristics of the target microalgae and the type of final value-added products, must be considered when selecting the appropriate harvesting technique. Furthermore, considerable aspects and possible future directions in flocculation, dewatering, and drying steps are proposed to develop scalable and low-cost microalgal harvesting systems.

Factors governing microalgae harvesting efficiency by flocculation using cationic polymers

This study aims to elucidate the mechanisms governing the harvesting efficiency of Chlorella vulgaris by flocculation using a cationic polymer. Flocculation efficiency increased as microalgae culture matured (i.e. 35-45, 75, and > 97% efficiency at early, late exponential, and stationary phase, respectively. Unlike the negative impact of phosphate on flocculation in traditional wastewater treatment; here, phosphorous residue did not influence the flocculation efficiency of C. vulgaris. The observed dependency of flocculation efficiency on growth phase was driven by changes in microalgal cell properties. Microalgal extracellular polymeric substances (EPS) in both bound and free forms at stationary phase were two and three times higher than those at late and early exponential phase, respectively. Microalgae cells also became more negatively charged as they matured. Negatively charged and high EPS content together with the addition of high molecular weight and positively charged polymer could facilitate effective flocculation via charge neutralisation and bridging.

Nanomagnetic approach applied to microalgae biomass harvesting: advances, gaps, and perspectives

Microalgae biomass is a versatile option for a myriad of purposes, as it does not require farmable land for cultivation and due of its high CO₂ fixation efficiency during growth. However, biomass harvesting is considered a bottleneck in the process because of its high cost. Magnetic harvesting is a promising method on account of its low cost, high harvesting speed, and efficiency, which can be used to improve the results of other harvesting methods. Here, we present the state of the art of the magnetic harvesting method. Detailed approaches involving different nanomaterials are described, including types, route of synthesis, and functionalization, variables that interfere with harvesting, and recycling methods of nanoparticles and medium. In addition to discussing the overall perspectives of the method, we provide a guideline for future research.

Recent trends in microbial nanoparticle synthesis and potential application in environmental technology: a comprehensive review

Microbial technology comprising environment in various aspects of pollution monitoring, treatment of pollutants, and energy generation has been put forth by the researchers worldwide in an eco-friendly manner. During the past few decades, this revolution has pronounced microbial cells in green nanotechnology, extending the scope, efficiency, and investment capita at research institutes, industries, and global markets. In the present review, initially, the source for the microbial synthesis of nanoparticles will be discussed involving bacteria, fungi, actinomycetes, microalgae, and viruses. Further, the mechanism and bio-components of microbial cells such as enzymes, proteins, peptides, amino-acids, exopolysaccharides, and others involved in the bio-reduction of metal ions to corresponding metal nanoparticles will be emphasized. The biosynthesized nanoparticles physicochemical properties and bio-reduction methods' advantages compared with synthetic methods will be detailed. To understand the suitability of biosynthesized nanoparticles in a wide range of applications, an overview of its blend of medicine, agriculture, and electronics will be discussed. This will be geared up with its applications specific to environmental aspects such as bioremediation, wastewater treatment, green-energy production, and pollution monitoring. Towards the end of the review, nano-waste management and limitations, i.e., void gaps that tend to impede the application of biosynthesized nanoparticles and microbial-based nanoparticles' prospects, will be deliberated. Thus, the review would claim to be worthy of unwrapping microorganisms sustainability in the emerging field of green nanotechnology.

A multicriteria decision analysis for the evaluation of microalgal growth and harvesting

Biomass obtained from microalgae research studies gained momentum in recent years because of their extensive application potential in multiple industries such as high-value nutraceuticals, bioproducts, cosmetics, animal feed industries, and biofuels while being a sustainable and environmentally friendly option. Although they have high biomass yields and rapid growth rates there are some limitations and challenges that remain for large-scale commercialized cultivation and harvesting methods of microalgae. Since there are multiple pathways related to efficient cultivation and harvesting methods to be viable, this study adopted, TOPSIS (Technique for Order Preference by Similarity to Ideal Solution), a multicriteria decision-making tool, to find the most acceptable alternative by using excel spreadsheets to evaluate the information that is derived from literature and pilot-scale studies. As a result, tubular (helical) and plate (flat panel) photobioreactors (PBRs) for cultivation and chemical harvesting (with chitosan) and bio-flocculation for harvesting were deemed suitable, while plastic bag PBR and suspended air flotation were deemed unsuitable.

Simultaneous removal of cyanobacterial blooms and production of clean water by coupling flocculation with a rotary drum filter

A mechanical harvesting technology based on coupling flocculation with a rotary drum filter (RDF, 35-μm) was applied to remove cyanobacterial blooms and produce clean water in Lake Caohai, a sub-lake of Lake Dianchi (Kunming, China). After treatment with a shipboard RDF and cationic polyacrylamide (CPAM, 0.5-2 mg/L) flocculation, > 95% of cyanobacterial biomass was removed. The chlorophyll-a (Chl-a) concentration and turbidity in the effluent were < 8 μg/L and < 3 NTU, respectively. Nutrient concentrations were also markedly reduced, with a permanganate index (PI) of < 2 mg/L and total phosphorus concentration of < 20 μg/L. The total nitrogen concentration was reduced from 2.75 to 1.65 mg/L, and most of the residual nitrogen was nitrate. Although powerful for the removal of suspended particles and an enhanced water transparency, the combined technology showed no significant reduction in inorganic nutrients and only a slight reduction in dissolved organic matter (DOM). The concentrations of protein and polysaccharide were significantly reduced, while that of humic matter did not change during the process. After flushing with the effluent of the RDF, a 20,000-m³ enclosure of lake water became clear when the volume of the effluent was 1.8 times that of the water enclosure. The electrical energy per order (EE/O) was calculated to be 0.053kWh/m³, which is lower than that of transferring water from more than 10 km away (0.058 kWh/m³). Thus, a shipboard RDF coupled with CPAM flocculation is a promising approach to remove harmful cyanobacterial blooms and improve the water environment of eutrophic lakes.

Insights into bioflocculation of filamentous cyanobacteria, microalgae and their mixture for a low-cost biomass harvesting system

Cyanobacteria and microalgae are considered as interesting feedstocks for either the production of high value bio-based compounds and biofuels or wastewater treatment. Nevertheless, the high costs of production, mainly due to the harvesting process, hamper a wide commercialization of industrial cyanobacteria and microalgae based products. Recent studies have found in autoflocculation and bioflocculation promising spontaneous processes for a low-cost and environmentally sustainable cyanobacteria and microalgae biomass harvesting process. In the present work, bioflocculation process has been studied for three different inocula: filamentous cyanobacteria, microalgae and their mixture. Their cultivation has been conducted in batch mode using two different cultivation media: synthetic aqueous solution and urban wastewater. The removal of nutrients and flocculation process performance were monitored during the entire cultivation time. Results have proved that bioflocculation and sedimentation processes occur efficiently for filamentous cyanobacteria cultivated in synthetic aqueous solution, whereas such processes are less efficient in urban wastewater due to the specific characteristics of this medium that prevent bioflocculation to occur. Besides different efficiencies associated to cultivation media, this work highlighted that bioflocculation of sole microalgae is not as effective as when they are cultivated together with filamentous cyanobacteria.

Sustainably Cultivating and Harvesting Microalgae through Sedimentation and Forward Osmosis Using Wastes

Cost-effective nutrient sources and dewatering are major obstacles to sustainable, scaled-up cultivation of microalgae. Employing waste resources as sources of nutrients offsets costs for nutrient supplies while adding value through simultaneous waste treatment. Forward osmosis (FO), using simulated reverse osmosis brine, is a low-energy membrane technology that can be employed to efficiently harvest microalgae from a dilute solution. In this study, Scenedesmus obliquus, a green microalga, was cultivated with a fertilizer plant wastewater formula and simulated coal-fired power plant flue gas and then separated through either FO, with reverse osmosis reject model water as the draw solution, or sedimentation. Microalgal batches grown with simulated wastewater removed NH₄ ⁺ within 2 days and reached nitrogen and phosphorus limitation simultaneously on Day 5. Sparging with the flue gas caused S. obliquus to produce significantly greater quantities of extracellular polymeric substances (30.7 ± 1.8 μg mL^-1), which caused flocculation and enhanced settling to an advantageous extent. Five-hour FO trials showed no statistically significant difference (p = 0.65) between water fluxes for cultures grown with simulated flue gas and CO₂-supplemented air (3.0 ± 0.1 and 3.0 ± 0.3 LMH, respectively). Reverse salt fluxes were low for all conditions and, remarkably, the rate of reverse salt flux was -1.9 ± 0.6 gMH when the FO feed was culture grown with simulated flue gas. In this work, S. obliquus was cultivated and harvested with potential waste resources.

Extracellular Polymeric Substances (EPS) as Microalgal Bioproducts: A Review of Factors Affecting EPS Synthesis and Application in Flocculation Processes

Microalgae are natural resources of intracellular compounds with a wide spectrum of applications in, e.g., the food industry, pharmacy, and biofuel production. The extracellular polymeric substances (EPS) released by microalgal cells are a valuable bioproduct. Polysaccharides, protein, lipids, and DNA are the main constituents of EPS. This review presents the recent advances in the field of the determinants of the synthesis of extracellular polymeric substances by microalgal cells and the EPS structure. Physical and chemical culture conditions have been analyzed to achieve useful insights into the development of a strategy optimizing EPS production by microalgal cells. The application of microalgal EPS for flocculation and mechanisms involved in this process are also discussed in terms of biomass harvesting. Additionally, the ability of EPS to remove toxic heavy metals has been analyzed. With their flocculation and sorption properties, microalgal EPS are a promising bioproduct that can potentially be used in harvesting algal biomass and wastewater management.

Co-cultivation of Streptomyces and microalgal cells as an efficient system for biodiesel production and bioflocculation formation

The phytohormone producing Streptomyces rosealbus MTTC 12,951 (S.R) and green microalga Chlorella vulgaris MSU-AGM 14 (C.V) were cultivated in co-culture system to evaluate exogenous hormonal activity. Biosynthesis of indole-3-acetic acid (IAA) and their precursors were quantitatively evaluated by employing High Performance Liquid Chromatography (HPLC). The concentration of IAA (0.72 ± 0.02 µg mL^-1) was observed to be elevated in co-cultivation system due to symbiotic interaction between Streptomyces and microalgae. In exchange, microalgae produced adequate volume of tryptophan (Trp) to induce IAA biosynthesis. The Trp stress in late exponential phase encouraged lipid accumulation (175 ± 10 mg g^-1). The bioflocculation property of microalgae ensures potential and economic viable harvesting process by reducing 148% input energy compared to conventional method. The overall results evidenced that C.V co-cultivation with S.R exhibits promotional behavior and serves as a promising cultivation process for microalgae in terms of cost efficiency and energy conservation.

A strategic approach to apply bacterial substances for increasing metabolite productions of Euglena gracilis in the bioreactor

Bacterial extracellular polymeric substances (EPS) are promising materials that have a role in enhancing growth, metabolite production, and harvesting efficiency. However, the validity of the EPS effectiveness in scale-up cultivation of microalgae is still unknown. Therefore, in order to verify whether the bacterial metabolites work in the scale-up fermentation of microalgae, we conducted a bioreactor fermentation following the addition of bacterial EPS derived from the marine bacterium, Pseudoalteromonas sp., to Euglena gracilis. Various culture strategies (i.e., batch, glucose fed-batch, and glucose and EPS fed-batch) were conducted to maximize metabolite production of E. gracilis in scale-up cultivation. Consequently, biomass and paramylon concentrations in the continuous glucose and EPS-treated culture were enhanced by 3.0-fold and 4.2-fold (36.1 ± 1.4 g L^-1 and 25.6 ± 0.1 g L^-1), respectively, compared to the non-treated control (12.0 ± 0.3 g L^-1 and 6.1 ± 0.1 g L^-1). Also, the supplementation led to the enhanced concentrations of α-tocopherols and total fatty acids by 3.7-fold and 2.8-fold, respectively. The harvesting efficiency was enhanced in EPS-supplemented cultivation due to the flocculation of E. gracilis. To the best of our knowledge, this is the first study that verifies the effect of bacterial EPS in scale-up cultivation of microalgae. Also, our results showed the highest paramylon productivity than any other previous reports. The results obtained in this study showed that the scale-up cultivation of E. gracilis using bacterial EPS has the potential to be used as a platform to guide further increases in scale and in the industrial environment. KEY POINTS: Effect of EPS on Euglena gracilis fermentation was tested in bioreactor scale. EPS supplement was effective for the paramylon, α-tocopherol, and lipid production. EPS supplement induced the flocculation of E. gracilis.